Sierra Wireless MHS802 CDMA + WiMAX + WiFi Hot Spot User Manual
Sierra Wireless Inc. CDMA + WiMAX + WiFi Hot Spot
Contents
- 1. User Manual
- 2. Users Manual
- 3. Box statements
- 4. Box Statements
User Manual
![](/img.php?id=1412542&img=bg1.png)
AirCard W802S Personal Hotspot
User Guide
2400092
Rev 1
![](/img.php?id=1412542&img=bg3.png)
Preface
Rev 1 Oct.10 3
Important
Notice
Due to the nature of wireless communications, transmission and reception of data
can never be guaranteed. Data may be delayed, corrupted (i.e., have errors) or be
totally lost. Although significant delays or losses of data are rare when wireless
devices such as the Sierra Wireless modem are used in a normal manner with a
well-constructed network, the Sierra Wireless modem should not be used in
situations where failure to transmit or receive data could result in damage of any
kind to the user or any other party, including but not limited to personal injury,
death, or loss of property. Sierra Wireless accepts no responsibility for damages
of any kind resulting from delays or errors in data transmitted or received using
the Sierra Wireless modem, or for failure of the Sierra Wireless modem to
transmit or receive such data.
Safety and
Hazards
Do not operate the Sierra Wireless modem in areas where blasting is in progress,
where explosive atmospheres may be present, near medical equipment, near life
support equipment, or any equipment which may be susceptible to any form of
radio interference. In such areas, the Sierra Wireless modem MUST BE
POWERED OFF. The Sierra Wireless modem can transmit signals that could
interfere with this equipment.
Do not operate the Sierra Wireless modem in any aircraft, whether the aircraft is
on the ground or in flight. In aircraft, the Sierra Wireless modem MUST BE
POWERED OFF. When operating, the Sierra Wireless modem can transmit
signals that could interfere with various onboard systems.
Note: Some airlines may permit the use of cellular phones while the aircraft is on the
ground and the door is open. Sierra Wireless modems may be used at this time.
The driver or operator of any vehicle should not operate the Sierra Wireless
modem while in control of a vehicle. Doing so will detract from the driver or
operator's control and operation of that vehicle. In some states and provinces,
operating such communications devices while in control of a vehicle is an offence.
Limitation of
Liability
The information in this manual is subject to change without notice and does not
represent a commitment on the part of Sierra Wireless. SIERRA WIRELESS AND
ITS AFFILIATES SPECIFICALLY DISCLAIM LIABILITY FOR ANY AND ALL
DIRECT, INDIRECT, SPECIAL, GENERAL, INCIDENTAL, CONSEQUENTIAL,
PUNITIVE OR EXEMPLARY DAMAGES INCLUDING, BUT NOT LIMITED TO,
LOSS OF PROFITS OR REVENUE OR ANTICIPATED PROFITS OR REVENUE
ARISING OUT OF THE USE OR INABILITY TO USE ANY SIERRA WIRELESS
PRODUCT, EVEN IF SIERRA WIRELESS AND/OR ITS AFFILIATES HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR THEY ARE
FORESEEABLE OR FOR CLAIMS BY ANY THIRD PARTY.
Notwithstanding the foregoing, in no event shall Sierra Wireless and/or its
affiliates aggregate liability arising under or in connection with the Sierra Wireless
product, regardless of the number of events, occurrences, or claims giving rise to
liability, be in excess of the price paid by the purchaser for the Sierra Wireless
product.
![](/img.php?id=1412542&img=bg4.png)
AirCard W802S User Guide
42400092
Patents Portions of this product may be covered by some or all of the following US
patents:
5,515,013 5,629,960 5,845,216 5,847,553 5,878,234 5,890,057 5,929,815
6,169,884 6,191,741 6,199,168 6,339,405 6,359,591 6,400,336 6,516,204
6,561,851 6,643,501 6,653,979 6,697,030 6,785,830 6,845,249 6,847,830
6,876,697 6,879,585 6,886,049 6,968,171 6,985,757 7,023,878 7,053,843
7,106,569 7,145,267 7,200,512 7,295,171 7, 287,162 D442,170 D459,303
D599,256 D560,911
and other patents pending.
This product includes technology licensed from QUALCOMM® 3G
Manufactured or sold by Sierra Wireless or its licensees under one or more
patents licensed from InterDigital Group.
Licenses A large amount of the source code to this product is available under licenses
which are both free and open source. Most is available under the GNU General
Public License.
The remainder of the open source software which is not under the GPL is
available under one of a variety of more permissive licenses. Those that require
reproduction of the license text in the distribution are listed in the sections that
follow (starting on page 10).
GNU General Public License
Version 2, June 1991
Copyright (C) 1989, 1991 Free Software Foundation, Inc. 51 Franklin St, Fifth
Floor, Boston, MA 02110-1301 USA
Everyone is permitted to copy and distribute verbatim copies of this license
document, but changing it is not allowed.
Preamble
The licenses for most software are designed to take away your freedom to share
and change it. By contrast, the GNU General Public License is intended to
guarantee your freedom to share and change free software--to make sure the
software is free for all its users. This General Public License applies to most of the
Free Software Foundation's software and to any other program whose authors
commit to using it. (Some other Free Software Foundation software is covered by
the GNU Library General Public License instead.) You can apply it to your
programs, too.
When we speak of free software, we are referring to freedom, not price. Our
General Public Licenses are designed to make sure that you have the freedom to
distribute copies of free software (and charge for this service if you wish), that you
receive source code or can get it if you want it, that you can change the software
or use pieces of it in new free programs; and that you know you can do these
things.
To protect your rights, we need to make restrictions that forbid anyone to deny you
these rights or to ask you to surrender the rights. These restrictions translate to
certain responsibilities for you if you distribute copies of the software, or if you
modify it.
![](/img.php?id=1412542&img=bg5.png)
Preface
Rev 1 Oct.10 5
For example, if you distribute copies of such a program, whether gratis or for a
fee, you must give the recipients all the rights that you have. You must make sure
that they, too, receive or can get the source code. And you must show them these
terms so they know their rights.
We protect your rights with two steps: (1) copyright the software, and (2) offer you
this license which gives you legal permission to copy, distribute and/or modify the
software.
Also, for each author’s protection and ours, we want to make certain that
everyone understands that there is no warranty for this free software. If the
software is modified by someone else and passed on, we want its recipients to
know that what they have is not the original, so that any problems introduced by
others will not reflect on the original authors' reputations.
Finally, any free program is threatened constantly by software patents. We wish to
avoid the danger that redistributors of a free program will individually obtain
patent licenses, in effect making the program proprietary. To prevent this, we have
made it clear that any patent must be licensed for everyone's free use or not
licensed at all.
The precise terms and conditions for copying, distribution and modification follow.
GNU GENERAL PUBLIC LICENSE
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND
MODIFICATION
0. This License applies to any program or other work which contains a notice
placed by the copyright holder saying it may be distributed under the terms of this
General Public License. The “Program”, below, refers to any such program or
work, and a “work based on the Program” means either the Program or any
derivative work under copyright law: that is to say, a work containing the Program
or a portion of it, either verbatim or with modifications and/or translated into
another language. (Hereinafter, translation is included without limitation in the
term “modification”.) Each licensee is addressed as “you”.
Activities other than copying, distribution and modification are not covered by this
License; they are outside its scope. The act of running the Program is not
restricted, and the output from the Program is covered only if its contents
constitute a work based on the Program (independent of having been made by
running the Program). Whether that is true depends on what the Program does.
1. You may copy and distribute verbatim copies of the Program’s source code as
you receive it, in any medium, provided that you conspicuously and appropriately
publish on each copy an appropriate copyright notice and disclaimer of warranty;
keep intact all the notices that refer to this License and to the absence of any
warranty; and give any other recipients of the Program a copy of this License
along with the Program.
You may charge a fee for the physical act of transferring a copy, and you may at
your option offer warranty protection in exchange for a fee.
2. You may modify your copy or copies of the Program or any portion of it, thus
forming a work based on the Program, and copy and distribute such modifications
or work under the terms of Section 1 above, provided that you also meet all of
these conditions: a) You must cause the modified files to carry prominent notices
![](/img.php?id=1412542&img=bg6.png)
AirCard W802S User Guide
62400092
stating that you changed the files and the date of any change. b) You must cause
any work that you distribute or publish, that in whole or in part contains or is
derived from the Program or any part thereof, to be licensed as a whole at no
charge to all third parties under the terms of this License. c) If the modified
program normally reads commands interactively when run, you must cause it,
when started running for such interactive use in the most ordinary way, to print or
display an announcement including an appropriate copyright notice and a notice
that there is no warranty (or else, saying that you provide a warranty) and that
users may redistribute the program under these conditions, and telling the user
how to view a copy of this License. (Exception: if the Program itself is interactive
but does not normally print such an announcement, your work based on the
Program is not required to print an announcement.)
These requirements apply to the modified work as a whole. If identifiable sections
of that work are not derived from the Program, and can be reasonably considered
independent and separate works in themselves, then this License, and its terms,
do not apply to those sections when you distribute them as separate works. But
when you distribute the same sections as part of a whole which is a work based
on the Program, the distribution of the whole must be on the terms of this License,
whose permissions for other licensees extend to the entire whole, and thus to
each and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or contest your rights to
work written entirely by you; rather, the intent is to exercise the right to control the
distribution of derivative or collective works based on the Program.
In addition, mere aggregation of another work not based on the Program with the
Program (or with a work based on the Program) on a volume of a storage or
distribution medium does not bring the other work under the scope of this
License.
3. You may copy and distribute the Program (or a work based on it, under Section
2) in object code or executable form under the terms of Sections 1 and 2 above
provided that you also do one of the following: a) Accompany it with the complete
corresponding machine-readable source code, which must be distributed under
the terms of Sections 1 and 2 above on a medium customarily used for software
interchange; or, b) Accompany it with a written offer, valid for at least three years,
to give any third party, for a charge no more than your cost of physically
performing source distribution, a complete machine-readable copy of the
corresponding source code, to be distributed under the terms of Sections 1 and 2
above on a medium customarily used for software interchange; or, c) Accompany
it with the information you received as to the offer to distribute corresponding
source code. (This alternative is allowed only for noncommercial distribution and
only if you received the program in object code or executable form with such an
offer, in accord with Subsection b above.)
The source code for a work means the preferred form of the work for making
modifications to it. For an executable work, complete source code means all the
source code for all modules it contains, plus any associated interface definition
files, plus the scripts used to control compilation and installation of the
executable. However, as a special exception, the source code distributed need
not include anything that is normally distributed (in either source or binary form)
with the major components (compiler, kernel, and so on) of the operating system
on which the executable runs, unless that component itself accompanies the
executable.
![](/img.php?id=1412542&img=bg7.png)
Preface
Rev 1 Oct.10 7
If distribution of executable or object code is made by offering access to copy from
a designated place, then offering equivalent access to copy the source code from
the same place counts as distribution of the source code, even though third
parties are not compelled to copy the source along with the object code.
4. You may not copy, modify, sublicense, or distribute the Program except as
expressly provided under this License. Any attempt otherwise to copy, modify,
sublicense or distribute the Program is void, and will automatically terminate your
rights under this License. However, parties who have received copies, or rights,
from you under this License will not have their licenses terminated so long as
such parties remain in full compliance.
5. You are not required to accept this License, since you have not signed it.
However, nothing else grants you permission to modify or distribute the Program
or its derivative works. These actions are prohibited by law if you do not accept
this License. Therefore, by modifying or distributing the Program (or any work
based on the Program), you indicate your acceptance of this License to do so,
and all its terms and conditions for copying, distributing or modifying the Program
or works based on it.
6. Each time you redistribute the Program (or any work based on the Program),
the recipient automatically receives a license from the original licensor to copy,
distribute or modify the Program subject to these terms and conditions. You may
not impose any further restrictions on the recipients' exercise of the rights granted
herein. You are not responsible for enforcing compliance by third parties to this
License.
7. If, as a consequence of a court judgment or allegation of patent infringement or
for any other reason (not limited to patent issues), conditions are imposed on you
(whether by court order, agreement or otherwise) that contradict the conditions of
this License, they do not excuse you from the conditions of this License. If you
cannot distribute so as to satisfy simultaneously your obligations under this
License and any other pertinent obligations, then as a consequence you may not
distribute the Program at all. For example, if a patent license would not permit
royalty-free redistribution of the Program by all those who receive copies directly
or indirectly through you, then the only way you could satisfy both it and this
License would be to refrain entirely from distribution of the Program.
If any portion of this section is held invalid or unenforceable under any particular
circumstance, the balance of the section is intended to apply and the section as a
whole is intended to apply in other circumstances.
It is not the purpose of this section to induce you to infringe any patents or other
property right claims or to contest validity of any such claims; this section has the
sole purpose of protecting the integrity of the free software distribution system,
which is implemented by public license practices. Many people have made
generous contributions to the wide range of software distributed through that
system in reliance on consistent application of that system; it is up to the author/
donor to decide if he or she is willing to distribute software through any other
system and a licensee cannot impose that choice.
This section is intended to make thoroughly clear what is believed to be a
consequence of the rest of this License.
![](/img.php?id=1412542&img=bg8.png)
AirCard W802S User Guide
82400092
8. If the distribution and/or use of the Program is restricted in certain countries
either by patents or by copyrighted interfaces, the original copyright holder who
places the Program under this License may add an explicit geographical
distribution limitation excluding those countries, so that distribution is permitted
only in or among countries not thus excluded. In such case, this License
incorporates the limitation as if written in the body of this License.
9. The Free Software Foundation may publish revised and/or new versions of the
General Public License from time to time. Such new versions will be similar in
spirit to the present version, but may differ in detail to address new problems or
concerns.
Each version is given a distinguishing version number. If the Program specifies a
version number of this License which applies to it and “any later version”, you
have the option of following the terms and conditions either of that version or of
any later version published by the Free Software Foundation. If the Program does
not specify a version number of this License, you may choose any version ever
published by the Free Software Foundation.
10. If you wish to incorporate parts of the Program into other free programs
whose distribution conditions are different, write to the author to ask for
permission. For software which is copyrighted by the Free Software Foundation,
write to the Free Software Foundation; we sometimes make exceptions for this.
Our decision will be guided by the two goals of preserving the free status of all
derivatives of our free software and of promoting the sharing and reuse of
software generally.
NO WARRANTY
11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS
NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY
APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE
COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM
“AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE
ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM
IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME
THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.
12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO
IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO
MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED
ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL,
SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF
THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT
LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR
LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE
PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH
HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES.
END OF TERMS AND CONDITIONS
![](/img.php?id=1412542&img=bg9.png)
Preface
Rev 1 Oct.10 9
How to Apply These Terms to Your New Programs
If you develop a new program, and you want it to be of the greatest possible use
to the public, the best way to achieve this is to make it free software which
everyone can redistribute and change under these terms.
To do so, attach the following notices to the program. It is safest to attach them to
the start of each source file to most effectively convey the exclusion of warranty;
and each file should have at least the "copyright" line and a pointer to where the
full notice is found.
<one line to give the program's name and a brief idea
of what it does.>
Copyright (C) <year> <name of author>
This program is free software; you can redistribute it
and/or modify it under the terms of the GNU General
Public License as published by the Free Software
Foundation; either version 2 of the License, or (at
your option) any later version.
This program is distributed in the hope that it will be
useful, but WITHOUT ANY WARRANTY; without even the
implied warranty of MERCHANTABILITY or FITNESS FOR A
PARTICULAR PURPOSE. See the GNU General Public License
for more details.
You should have received a copy of the GNU General
Public License along with this program; if not, write
to the Free Software Foundation, Inc., 51 Franklin St,
Fifth Floor, Boston, MA 02110-1301 USA
Also add information on how to contact you by electronic and paper mail.
If the program is interactive, make it output a short notice like this when it starts in
an interactive mode:
Gnomovision version 69, Copyright (C) year name of
author
Gnomovision comes with ABSOLUTELY NO WARRANTY; for
details type 'show w'.
This is free software, and you are welcome to
redistribute it under certain conditions; type 'show c'
for details.
The hypothetical commands ‘show w’ and ‘show c’ should show the appropriate
parts of the General Public License. Of course, the commands you use may be
called something other than ‘show w’ and ‘show c’; they could even be mouse-
clicks or menu items--whatever suits your program.
You should also get your employer (if you work as a programmer) or your school,
if any, to sign a "copyright disclaimer" for the program, if necessary. Here is a
sample; alter the names:
Yoyodyne, Inc., hereby disclaims all copyright interest
in the program ‘Gnomovision’ (which makes passes at
compilers) written by James Hacker.
![](/img.php?id=1412542&img=bga.png)
AirCard W802S User Guide
10 2400092
<signature of Ty Coon>, 1 April 1989
Ty Coon, President of Vice
This General Public License does not permit incorporating your program into
proprietary programs. If your program is a subroutine library, you may consider it
more useful to permit linking proprietary applications with the library. If this is what
you want to do, use the GNU Library General Public License instead of this
License.
iPerf License
Copyright (c) 1999-2007, The Board of Trustees of the University of Illinois
All Rights Reserved.
Iperf performance test
Mark Gates
Ajay Tirumala
Jim Ferguson
Jon Dugan
Feng Qin
Kevin Gibbs
John Estabrook
National Laboratory for Applied Network Research
National Center for Supercomputing Applications
University of Illinois at Urbana-Champaign
http://www.ncsa.uiuc.edu
Permission is hereby granted, free of charge, to any person obtaining a copy of
this software (Iperf) and associated documentation files (the “Software”), to deal
in the Software without restriction, including without limitation the rights to use,
copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the
Software, and to permit persons to whom the Software is furnished to do so,
subject to the following conditions:
Redistributions of source code must retain the above copyright notice, this list of
conditions and the following disclaimers.
Redistributions in binary form must reproduce the above copyright notice, this list
of conditions and the following disclaimers in the documentation and/or other
materials provided with the distribution.
Neither the names of the University of Illinois, NCSA, nor the names of its
contributors may be used to endorse or promote products derived from this
Software without specific prior written permission. THE SOFTWARE IS
PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
![](/img.php?id=1412542&img=bgb.png)
Preface
Rev 1 Oct.10 11
NONINFRINGEMENT. IN NO EVENT SHALL THE CONTIBUTORS OR
COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,
ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR
THE USE OR OTHER DEALINGS IN THE SOFTWARE.
miniupnpd License
Copyright (c) 2006-2008, Thomas BERNARD
All rights reserved.
Redistribution and use in source and binary forms, with or without modification,
are permitted provided that the following conditions are met:
•Redistributions of source code must retain the above copyright notice, this list
of conditions and the following disclaimer.
•Redistributions in binary form must reproduce the above copyright notice, this
list of conditions and the following disclaimer in the documentation and/or
other materials provided with the distribution.
•The name of the author may not be used to endorse or promote products
derived from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND
CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
OpenSSL License
Copyright (c) 1998-2007 The OpenSSL Project. All rights reserved.
Redistribution and use in source and binary forms, with or without modification,
are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list
of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this
list of conditions and the following disclaimer in the documentation and/or
other materials provided with the distribution.
3. All advertising materials mentioning features or use of this software must
display the following acknowledgment:
4. “This product includes software developed by the OpenSSL Project for use in
the OpenSSL Toolkit. (http://www.openssl.org/)”
5. The names “OpenSSL Toolkit” and “OpenSSL Project” must not be used to
endorse or promote products derived from this software without prior written
![](/img.php?id=1412542&img=bgc.png)
AirCard W802S User Guide
12 2400092
permission. For written permission, please contact openssl-
core@openssl.org.
6. Products derived from this software may not be called “OpenSSL” nor may
“OpenSSL” appear in their names without prior written permission of the
OpenSSL Project.
7. Redistributions of any form whatsoever must retain the following acknowl-
edgment:
“This product includes software developed by the OpenSSL Project for use in
the OpenSSL Toolkit (http://www.openssl.org/)”
THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT “AS IS” AND
ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT
SHALL THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR
ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING
IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGE.
This product includes cryptographic software written by Eric Young
(eay@cryptsoft.com). This product includes software written by Tim Hudson
(tjh@cryptsoft.com).
Original SSLeay License
Copyright (C) 1995-1998 Eric Young (eay@cryptsoft.com)
All rights reserved.
This package is an SSL implementation written by Eric Young
(eay@cryptsoft.com).
The implementation was written so as to conform with Netscapes SSL.
This library is free for commercial and non-commercial use as long as the
following conditions are aheared to. The following conditions apply to all code
found in this distribution, be it the RC4, RSA, lhash, DES, etc., code; not just the
SSL code. The SSL documentation included with this distribution is covered by
the same copyright terms except that the holder is Tim Hudson
(tjh@cryptsoft.com).
Copyright remains Eric Young's, and as such any Copyright notices in the code
are not to be removed. If this package is used in a product, Eric Young should be
given attribution as the author of the parts of the library used. This can be in the
form of a textual message at program startup or in documentation (online or
textual) provided with the package.
Redistribution and use in source and binary forms, with or without modification,
are permitted provided that the following conditions are met:
![](/img.php?id=1412542&img=bgd.png)
Preface
Rev 1 Oct.10 13
1. Redistributions of source code must retain the copyright notice, this list of
conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this
list of conditions and the following disclaimer in the documentation and/or
other materials provided with the distribution.
3. All advertising materials mentioning features or use of this software must
display the following acknowledgement:
“This product includes cryptographic software written by Eric Young
(eay@cryptsoft.com)”
The word ‘cryptographic’ can be left out if the rouines from the library being
used are not cryptographic related :-).
4. If you include any Windows specific code (or a derivative thereof) from the
apps directory (application code) you must include an acknowledgement:
“This product includes software written by Tim Hudson (tjh@cryptsoft.com)”
THIS SOFTWARE IS PROVIDED BY ERIC YOUNG “AS IS” AND ANY
EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO,
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE
GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
DAMAGE.
The licence and distribution terms for any publically available version or derivative
of this code cannot be changed. i.e. this code cannot simply be copied and put
under another distribution licence [including the GNU Public Licence.]
PPPD License
Copyright (c) 1984-2000 Carnegie Mellon University. All rights reserved.
Redistribution and use in source and binary forms, with or without modification,
are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list
of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this
list of conditions and the following disclaimer in the documentation and/or
other materials provided with the distribution.
3. The name “Carnegie Mellon University” must not be used to endorse or
promote products derived from this software without prior written permission.
For permission or any legal details, please contact
Office of Technology Transfer
Carnegie Mellon University
5000 Forbes Avenue
![](/img.php?id=1412542&img=bge.png)
AirCard W802S User Guide
14 2400092
Pittsburgh, PA 15213-3890
(412) 268-4387, fax: (412) 268-7395
tech-transfer@andrew.cmu.edu
4. Redistributions of any form whatsoever must retain the following acknowl-
edgment:
“This product includes software developed by Computing Services at Carne-
gie Mellon University (http://www.cmu.edu/computing/).”
CARNEGIE MELLON UNIVERSITY DISCLAIMS ALL WARRANTIES WITH
REGARD TO THIS SOFTWARE, INCLUDING ALL IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS, IN NO EVENT SHALL CARNEGIE
MELLON UNIVERSITY BE LIABLE FOR ANY SPECIAL, INDIRECT OR
CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER
RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION,
ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE
OF THIS SOFTWARE.
Copyright (c) 1999-2004 Paul Mackerras. All rights reserved.
Redistribution and use in source and binary forms, with or without modification,
are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list
of conditions and the following disclaimer.
2. The name(s) of the authors of this software must not be used to endorse or
promote products derived from this software without prior written permission.
3. Redistributions of any form whatsoever must retain the following acknowl-
edgment:
“This product includes software developed by Paul Mackerras
<paulus@samba.org>”.
THE AUTHORS OF THIS SOFTWARE DISCLAIM ALL WARRANTIES WITH
REGARD TO THIS SOFTWARE, INCLUDING ALL IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS, IN NO EVENT SHALL THE AUTHORS BE
LIABLE FOR ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES OR
ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR
PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR
OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH
THE USE OR PERFORMANCE OF THIS SOFTWARE.
PPPStats License
Copyright (c) 1989 Regents of the University of California.
All rights reserved.
Redistribution and use in source and binary forms are permitted provided that the
above copyright notice and this paragraph are duplicated in all such forms and
that any documentation, advertising materials, and other materials related to such
distribution and use acknowledge that the software was developed by the
University of California, Berkeley. The name of the University may not be used to
endorse or promote products derived from this software without specific prior
written permission.
![](/img.php?id=1412542&img=bgf.png)
Preface
Rev 1 Oct.10 15
THIS SOFTWARE IS PROVIDED “AS IS” AND WITHOUT ANY EXPRESS OR
IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED
WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR A PARTICULAR
PURPOSE.
PPPDump License
Copyright (c) 1999 Paul Mackerras. All rights reserved.
Redistribution and use in source and binary forms, with or without modification,
are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list
of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this
list of conditions and the following disclaimer in the documentation and/or
other materials provided with the distribution.
3. The name(s) of the authors of this software must not be used to endorse or
promote products derived from this software without prior written permission.
4. Redistributions of any form whatsoever must retain the following acknowl-
edgment:
“This product includes software developed by Paul Mackerras
<paulus@samba.org>”.
THE AUTHORS OF THIS SOFTWARE DISCLAIM ALL WARRANTIES WITH
REGARD TO THIS SOFTWARE, INCLUDING ALL IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS, IN NO EVENT SHALL THE AUTHORS BE
LIABLE FOR ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES OR
ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR
PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR
OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH
THE USE OR PERFORMANCE OF THIS SOFTWARE.
SSH2 License
Copyright (c) 2004-2007 Sara Golemon <sarag@libssh2.org>
Copyright (C) 2006-2007 The Written Word, Inc.
All rights reserved.
Redistribution and use in source and binary forms, with or without modification,
are permitted provided that the following conditions are met:
Redistributions of source code must retain the above copyright notice, this list of
conditions and the following disclaimer.
Redistributions in binary form must reproduce the above copyright notice, this list
of conditions and the following disclaimer in the documentation and/or other
materials provided with the distribution.
Neither the name of the copyright holder nor the names of any other contributors
may be used to endorse or promote products derived from this software without
specific prior written permission.
![](/img.php?id=1412542&img=bg10.png)
AirCard W802S User Guide
16 2400092
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND
CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR
CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
UUID License
Copyright (c) 2004-2008 Ralf S. Engelschall <rse@engelschall.com>
Copyright (c) 2004-2008 The OSSP Project <http://www.ossp.org/>
This file is part of OSSP uuid, a library for the generation of UUIDs which can
found at http://www.ossp.org/pkg/lib/uuid/
Permission to use, copy, modify, and distribute this software for any purpose with
or without fee is hereby granted, provided that the above copyright notice and this
permission notice appear in all copies.
THIS SOFTWARE IS PROVIDED “AS IS” AND ANY EXPRESSED OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE ARE DISCLAIMED.
IN NO EVENT SHALL THE AUTHORS AND COPYRIGHT HOLDERS AND
THEIR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE
GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
DAMAGE.
Zlib License
Copyright (C) 1995-2010 Jean-loup Gailly and Mark Adler
This software is provided ‘as-is’, without any express or implied warranty. In no
event will the authors be held liable for any damages arising from the use of this
software.
Permission is granted to anyone to use this software for any purpose, including
commercial applications, and to alter it and redistribute it freely, subject to the
following restrictions:
1. The origin of this software must not be misrepresented; you must not claim
that you wrote the original software. If you use this software in a product, an
![](/img.php?id=1412542&img=bg11.png)
Preface
Rev 1 Oct.10 17
acknowledgment in the product documentation would be appreciated but is
not required.
2. Altered source versions must be plainly marked as such, and must not be
misrepresented as being the original software.
3. This notice may not be removed or altered from any source distribution.
Jean-loup Gailly
Mark Adler
Copyright © 2010 Sierra Wireless. All rights reserved.
Trademarks AirCard and “Heart of the Wireless Machine” are registered trademarks of Sierra
Wireless. AirPrime, AirLink, AirVantage, Sierra Wireless, the Sierra Wireless logo,
TRU-Install, and the red wave design are trademarks of Sierra Wireless.
Windows® and Windows Vista® are registered trademarks of Microsoft
Corporation.
Macintosh and Mac OS are trademarks of Apple Inc., registered in the U.S. and
other countries.
QUALCOMM® is a registered trademark of QUALCOMM Incorporated. Used
under license.
Linux® is the registered trademark of Linus Torvalds in the U.S. and other
countries.
Wi-Fi, WPA, and WPA2 are registered marks of the Wi-Fi Alliance.
QUALCOMM® is a registered trademark of QUALCOMM Incorporated.
Other trademarks are the property of their respective owners.
Contact
Information
Additional
Information and
Updates
For up-to-date product descriptions, documentation, application notes, firmware
upgrades, troubleshooting tips, and press releases, visit www.sierrawireless.com.
Sales Desk: Phone: 1-604-232-1488
Hours: 8:00 AM to 5:00 PM Pacific Time
E-mail: sales@sierrawireless.com
Post: Sierra Wireless
13811 Wireless Way
Richmond, BC
Canada V6V 3A4
Fax: 1-604-231-1109
Web: www.sierrawireless.com
![](/img.php?id=1412542&img=bg12.png)
AirCard W802S User Guide
18 2400092
Revision
History Revision
number Release
date Changes
1Oct 10 Initial release
![](/img.php?id=1412542&img=bg13.png)
Rev 1 Oct.10 19
Contents
Device Basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Your Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Components of your device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
3G and 4G Networks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Available accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
About This Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Getting Started With Your Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Your Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Installing the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Connecting Through USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Charging the Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Using the AC Charger with USB Port . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Charging Through a Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Power Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Turning Your Device On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Turning Your Device Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Using the Power Button to Determine the Device State . . . . . . . . . . . . .34
Controlling the Device Using the Power Button . . . . . . . . . . . . . . . . . . . .34
LCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Interpreting the LCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Mute Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
microSD Card Slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Installing and Setting Up the Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Setting Up the Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Connecting to the Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
![](/img.php?id=1412542&img=bg14.png)
AirCard W802S User Guide
20 2400092
Changing the Password and Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Activating and Using Your Network Service . . . . . . . . . . . . . . . . . . . . . . 41
Using Your Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Connecting Through USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
TRU-Install . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Requirements for a USB Tethered Connection . . . . . . . . . . . . . . . . . . . . 43
Making a Tethered Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Browser Interface Home Page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Displaying the Home Page of the Device . . . . . . . . . . . . . . . . . . . . . . . . 46
Logging On as an Administrator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Virtual Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Mini Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Turning Your Device Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Alerts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Displaying Alerts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
3G Activation Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
3G Network Update Available . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
SD Card Error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Software Update Available . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Your Network Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Launching Your Network Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Sharing Your Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Ending Your Network Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Vertical Row (of Icons and Text) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Signal Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Mobile Broadband Information and Settings . . . . . . . . . . . . . . . . . . . . . . 54
3G Roaming Information and Settings . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Alert Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Wi-Fi Users Information and Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Battery Information and Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Internet Connection Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
microSD Card Information and Settings . . . . . . . . . . . . . . . . . . . . . . . . . 58
Sounds Information and Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
![](/img.php?id=1412542&img=bg15.png)
Contents
Rev 1 Oct.10 21
Home Page Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Buttons Along the Top of the Home Page . . . . . . . . . . . . . . . . . . . . . . . .60
Buttons Below the Virtual Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
Using the microSD Card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Before Using the microSD Card Slot . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
Inserting a microSD Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
Removing a microSD Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
Accessing the microSD Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Updates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Automatically Checking for Updates . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
Manually Checking for Updates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
Upgrade Firmware From a File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
Viewing Device Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Reset Button. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Restarting the Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
Power Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Battery and USB Power Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
AC Power Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
Configuring the LCD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Turning the LCD On or Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
Setting the LCD Timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
Setting the LCD Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
Enabling and Disabling the LED. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Sounds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Enabling and Disabling Sounds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
Enabling and Disabling Sounds for Specific Events . . . . . . . . . . . . . . . .75
Low Battery Alert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
Critical Battery Level Alert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
Login Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Changing the Administrator Password . . . . . . . . . . . . . . . . . . . . . . . . . . .77
Automatic Login ("Remember Me") . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
![](/img.php?id=1412542&img=bg16.png)
AirCard W802S User Guide
22 2400092
Advanced Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Accessing the Advanced Settings Window . . . . . . . . . . . . . . . . . . . . . . . 78
Device Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
WAN Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Wi-Fi Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Configuring the Wi-Fi Network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
SSID (Wi-Fi Network Name) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Wi-Fi Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Host Name (Device Name) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Setting the Maximum Number of Wi-Fi Users . . . . . . . . . . . . . . . . . . . . . 92
Wi-Fi Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Disabling Wi-Fi When Connected Through USB . . . . . . . . . . . . . . . . . . . 93
Configuring 3G/4G. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Viewing 3G Activation Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
3G Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Resetting the 3G/4G Configuration to Default Settings . . . . . . . . . . . . . . 94
Configuring the Router Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Basic Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
LAN Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Port Forward Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Port Trigger Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
DMZ Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Resetting the Software to Default Settings . . . . . . . . . . . . . . . . . . . . . . 105
Exporting and Importing Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Exporting Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Importing Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Logs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Logs Available . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Connection History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
System Events . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Setting the Method Used for Time Acquisition . . . . . . . . . . . . . . . . . . . 109
Setup Pages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Welcome to Your Device Window - Select an Option . . . . . . . . . . . . . . 110
![](/img.php?id=1412542&img=bg17.png)
Contents
Rev 1 Oct.10 23
Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111
More Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Visiting the <Carrier_Name> Website . . . . . . . . . . . . . . . . . . . . . . . . . .111
Contacting Customer Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111
Online Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111
Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
How Can I Tell I'm Connected to 3G/4G? . . . . . . . . . . . . . . . . . . . . . . .112
How Do I Connect to Wi-Fi? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112
Is Roaming on 4G Supported? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112
What Do I Do if I Forgot the Wi-Fi Password? . . . . . . . . . . . . . . . . . . . .112
What Do I Do if I Forgot the Administrator Password? . . . . . . . . . . . . .113
How Do I Access My Corporate Network Through a VPN? . . . . . . . . . .113
Are Terminal Sessions Supported? . . . . . . . . . . . . . . . . . . . . . . . . . . . .113
Tips. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
Extending Battery Life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .113
Device Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .114
Improving Signal Strength . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .114
Improving 3G Network Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .115
Improving Wi-Fi Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .115
Security Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .116
Finding the MAC Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .117
Finding the IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .118
Troubleshooting Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
General tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .118
LCD Is Dark . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .119
Insufficient Signal Strength . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .119
Messages Displayed on the Device LCD . . . . . . . . . . . . . . . . . . . . . . . .119
Cannot Connect to Wi-Fi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .121
Cannot Display the Home Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122
Cannot Connect to the 3G/4G Network . . . . . . . . . . . . . . . . . . . . . . . . .123
Cannot Check for Updates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .123
Sounds are Enabled, but the Device Doesn't Generate Any Sounds . .123
![](/img.php?id=1412542&img=bg18.png)
AirCard W802S User Guide
24 2400092
Technical Specifications, Safety Information, and
Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
LED Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
Radio Frequency and Electrical Specifications . . . . . . . . . . . . . . . . . . . 125
Software Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Environmental Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Mechanical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
![](/img.php?id=1412542&img=bg19.png)
Rev 1 Oct.10 25
1
1: Device Basics
Your AirCard W802S personal hotspot allows you to easily connect
to the Internet and to share your 3G/4G connection with others.
This user guide describes how to set up your device and use the
browser interface to:
•View the status of your device.
•View and change the settings of your device and the browser
interface.
It also describes your device (its various connectors and buttons).
Your Device
The AirCard W802S personal hotspot provides a simple way to use
your 3G/4G Internet connection with any Wi-Fi-enabled device, and
to share your Internet connection with friends and family.
![](/img.php?id=1412542&img=bg1a.png)
AirCard W802S User Guide
26 2400092
Components of your device
Your device consists of these main components:
•Wi-Fi access point
The Wi-Fi access point connects your computers and other Wi-Fi-enabled
devices to your device.
•3G modem
The 3G modem connects your device to the Internet via the 3G (CDMA 1X/
EVDO) network (more widely available, compared to 4G).
•4G modem
The 4G modem connects your device to the Internet via the 4G (WiMAX) net-
work (newer technology and faster speeds, compared to 3G).
•Routing hardware
The routing hardware handles traffic between the 3G/4G modems, the Wi-Fi
access point, and the Wi-Fi network.
3G and 4G Networks
These wireless networks connect you to the Internet. Depending on your
coverage area, you may have:
•Both 3G and 4G coverage
•Only 3G coverage
•Only 4G coverage.
Your device automatically connects to the fastest network that is available to you.
If you have both 3G and 4G coverage and your connection happens to get
disrupted, your device can automatically switch to the other network. For more
information, see "Configuring the 3G/4G Connection Preferences" on page 54.
Download speeds
Actual speeds depend on several factors, including network conditions.
Note: You can get even higher download speeds, by using the optional Home Crib
(available for purchase separately).
Wireless mode Maximum downlink
speeds Typical downlink
speeds
3G (EV-DO Rev 0) 2.4 Mbps 400-700 kbps
3G (EV-DO Rev A) 3 Mbps 0.6-1.4 Mbps
4G 10 Mbps 3-6 Mbps
![](/img.php?id=1412542&img=bg1b.png)
Device Basics
Rev 1 Oct.10 27
Package Contents
Your package includes:
•AirCard W802S personal hotspot by Sierra Wireless
•Battery compartment cover
•Rechargeable battery
•Power adapter
•USB cable
•Quick Start guide
Available accessories
The following accessories are available for purchase separately:
•Home Crib—improves download speeds, and also charges the device.
•High-capacity battery
To purchase them, please visit https://www.sierrawireless.com/eStore/. Other
accessories may also be available.
Care and Maintenance
As with any electronic device, you should handle this device with care to ensure
reliable operation. Follow these guidelines in using and storing the device:
•Protect the device from liquids, dust, and excessive heat.
•Do not handle or operate the device while driving or operating a vehicle.
Doing so may distract you from properly operating the vehicle. In some juris-
dictions, operating communication devices while in control of a vehicle is a
criminal offense.
•Do not apply adhesive labels to the device. They may cause the device to
overheat and may alter the antenna's performance.
About This Guide
This user guide provides you with all the information you'll need to install and use
your AirCard W802S personal hotspot.
The printed Quick Start guide that comes with the AirCard W802S personal
hotspot should be sufficient for most installations.
•Chapter 1 (which you are reading) gives you an overview of the device.
•Chapter 2 describes the buttons, connectors, and other components of the
device. (See "Your Device" on page 29).
•Chapter 3 provides step-by-step instructions for setting up the device. (See
"Installing and Setting Up the Device" on page 37).
•Chapter 4 describes common tasks for your device. (See "Using Your Device"
on page 43).
•Chapter 5 describes advanced configuration of the device and the browser
interface. (See "Settings" on page 73).
![](/img.php?id=1412542&img=bg1c.png)
AirCard W802S User Guide
28 2400092
•Chapter 6 contains frequently asked questions, troubleshooting tips, and
resources for getting help. (See "Resources" on page 111).
•Chapter 7 lists the electrical, radio frequency, and other parameters of the
device for those who require technical information, as well as safety infor-
mation and regulatory information. (See "Technical Specifications, Safety
Information, and Regulatory Information" on page 125).
Getting Started With Your Device
System Requirements
•One or more computers that support Wi-Fi (802.11b/g/n)
•Web browser (required if you'll be using the browser interface to view status
and to configure settings). The following browsers are supported:
·Internet Explorer (version 6.0 or higher)
·Mozilla Firefox (version 3.0 or higher)
·Google Chrome (version 2.0.172.28 or higher)
·Apple Safari (version 2.0 or higher)
•If you'll be connecting the device through USB:
·Computer running Windows 7, Windows Vista, Windows XP with Service
Pack 2, or Mac (OS X 10.4.x or higher)
·USB 2.0 slot
![](/img.php?id=1412542&img=bg1d.png)
Rev 1 Oct.10 29
2
2: Your Device
Battery
The battery compartment is on the back of the device. The battery is
replaceable.
If you need a new battery or want to purchase a high-capacity battery
(which provides improved battery life), visit the Sierra Wireless online
store at https://www.sierrawireless.com/eStore/.
Installing the Battery
1. Remove the battery compartment cover.
![](/img.php?id=1412542&img=bg1e.png)
AirCard W802S User Guide
30 2400092
2. Align the battery contact points with those inside the battery compartment,
and insert the battery into the device.
3. Replace the battery compartment cover.
Connecting Through USB
Note: If you’ll be using USB for data transfer (and not just for charging the device), you
must install the device driver. See "Making a Tethered Connection" on page 43.
![](/img.php?id=1412542&img=bg1f.png)
Your Device
Rev 1 Oct.10 31
Use the USB cable to connect the device to your computer when:
•You want to charge the device, but you don't want to use the power adapter,
or the power adapter is not available.
•Your computer does not have Wi-Fi.
•You want to block others from using the device. (See "Disabling Wi-Fi When
Connected Through USB" on page 93.)
To connect the device to your computer:
1. Insert the larger (USB) end of the USB cable into the computer.
2. Insert the other (Micro B) end of the USB cable into the USB connector on the
side of the device.
Charging the Device
You need to recharge your device's battery periodically. You can continue using
your device while it is charging.
To charge the battery, you have two options, as shown in the drawing that follows
— you can connect the device to an AC charger (faster way to charge). See
"Using the AC Charger with USB Port" on page 32. Alternatively, you can charge
the device when it’s inserted into the optional Home Crib, or you can connect the
device to a computer (slower way to charge). See "Charging Through a
Computer" on page 32.
![](/img.php?id=1412542&img=bg20.png)
AirCard W802S User Guide
32 2400092
Using the AC Charger with USB Port
1. Insert the smaller (Micro B) end of the USB cable into the USB connector on
the side of the device.
2. Insert the other (USB) end of the USB cable into the power adapter.
3. Insert the power adapter into an electrical outlet.
When charging, the LCD shows and, if the device is off, displays a message
"Charging... xx% complete".
When the device is charged, the LCD shows:
• (if the device is on)
• and the message "Fully charged" (if the device is off).
Charging Through a Computer
Note: Charging through a computer usually takes longer than charging through the power
adapter.
Note: If you’ll be using USB for data transfer (and not just for charging the device), you
must install the device driver. See "Making a Tethered Connection" on page 43.
![](/img.php?id=1412542&img=bg21.png)
Your Device
Rev 1 Oct.10 33
Note: If you’re using Mac OS X 10.4.x, after you connect the device you may see a
warning message that your computer is running on UPS backup battery and that you
should perform a computer shutdown. You can continue with your work. To prevent this
message from being displayed, install the device driver. See "Making a Tethered
Connection" on page 43.
1. Ensure the computer is turned on.
2. Insert the larger (USB) end of the USB cable into the computer.
3. Insert the other (Micro B) end of the USB cable into the USB connector on
the side of the device.
When charging, the LCD shows .
When the device is charged, the LCD shows .
Power Button
Turning Your Device On
1. Ensure that:
·The device has a charged battery inserted.
— or —
·The device is connected to the power adapter or a computer (through the
USB cable), as shown in the drawing on page 31.
2. If the device LCD is blank, press and hold the power button for two
seconds.
Turning Your Device Off
•Press and hold the power button for 2 seconds.
![](/img.php?id=1412542&img=bg22.png)
AirCard W802S User Guide
34 2400092
Using the Power Button to Determine the Device State
The power button on the device also indicates the device's status, as shown in
the following table.
Controlling the Device Using the Power Button
Power button Description Your action
Not lit •The device is turned off, and may or
may not be charging.
•The device is turned on, but you have
turned off the LED.
•To turn the device on, press and hold the
power button for two seconds.
•[OPTIONAL]: Turn on the LED. See
"Enabling and Disabling the LED" on
page 74.
Lit, flashing
(approximately every
4 seconds)
The device is turned on, and the LED is
enabled. No action required.
Lit, flashing
(approximately every
30 seconds)
The device is in standby (low power) mode.
The following are off: LCD, Wi-Fi radio, 3G/
4G radios.
For more information, see "Standby (Low
Power) Mode" on page 57.
To exit standby mode:
Connect the device to the power adapter or
computer, through the USB cable.
— or —
Press the power button .
Type of press Result
Quick press •The device leaves standby (low power) mode.
•The LCD wakes up (turns on) if it was enabled but dormant. (The LCD turns dark,
after a configurable time of inactivity.)
•A displayed message is confirmed or acknowledged.
•Display of the Wi-Fi network name (SSID) and password is turned off.
Quick double-press •The LCD wakes up (turns on) if it was enabled but dormant. (The LCD turns dark,
after a configurable time of inactivity.)
•The Wi-Fi network name (SSID) and password are briefly displayed. See "Wi-Fi
Password Reminder" on page 90.
Long press (press and hold
for two seconds) The device turns on or off.
![](/img.php?id=1412542&img=bg23.png)
Your Device
Rev 1 Oct.10 35
LCD
If the LCD is not lit, see "Turning Your Device On" on page 33.
Interpreting the LCD
The LCD shows icons and text that reflect the status of the device and your
connection.
Tip: Most of the LCD icons and messages are also shown on the Virtual Device (page 47)
and Mini Window (page 48). See also "Messages Displayed on the Device LCD" on
page 119.
ASignal strength
B3G/4G status
CAlerts
DNumber of Wi-Fi users
EBattery status
FDevice name. Message area.
GAmount of data transferred; connection duration. Message area.
AB C DE
F
G
![](/img.php?id=1412542&img=bg24.png)
AirCard W802S User Guide
36 2400092
Mute Switch
The mute switch is used to turn on or off sounds from the device. The mute switch
is located on the side of the device:
Tip: You can also disable sounds through the home page. See "Sounds Information
and Settings" on page 59.
microSD Card Slot
Your device supports a microSD™ card (sold separately) for file sharing and
transfer or storage. The microSD slot is located on the same side of the device as
the USB connector. Your computer recognizes the microSD card as a removable
storage device. The device supports microSD cards up to 16 GB.
Note: Using microSD cards larger than 16 GB can cause data loss and damage your
device.
![](/img.php?id=1412542&img=bg25.png)
Rev 1 Oct.10 37
3
3: Installing and Setting Up the Device
Setting Up the Device
1. Install the battery, as described in "Installing the Battery" on
page 29.
2. Connect the device to the AC charger, as described in "Using the
AC Charger with USB Port" on page 32.
3. Plug the AC charger into an electrical outlet.
4. Important: Charge the device until the battery icon is full ( ).
Connecting to the Network
1. Ensure you are in the <Carrier_Name> 3G or 4G coverage area
(not roaming).
2. If you have a LAN connection, disconnect it.
3. Ensure your computer's Wi-Fi is turned on.
4. If the device LCD displays "Charging", "Charged", or "Powered
off", press and hold the power button for two seconds.
5. Wait until the device LCD displays "Connect your computer to
Wi-Fi network," followed by the network name (SSID) and
password. This may take several seconds.
6. On your computer, connect to the Wi-Fi network listed on the
device LCD. If you don't know how to do this, see "How Do
I Connect to Wi-Fi?" on page 112. After you’ve connected to the
Wi-Fi network, the device LCD displays "Open any web page to
continue setup."
7. Open your Web browser. The "Welcome to your AirCard W802S"
window opens.
Note: This window displays the administrator password and the address of
the device home page. Please remember this information or write it down in a
safe place.
![](/img.php?id=1412542&img=bg26.png)
AirCard W802S User Guide
38 2400092
This window provides several options.
•To keep the default settings of the device, click one of the following:
·The Internet (to start surfing)
·My AirCard W802S's home page (to view the device status, customize
settings). Proceed to "Using Your Device" on page 43.
•To change security settings, click Set up my AirCard W802S.
Changing the Password and Settings
During the device setup, you can select Set up my AirCard W802S to change the
settings for the:
•Administrator password
This password is used to log in to the home page, where you can view and
customize your device settings. The default password is "password". Choose
something easy-to-remember (yet not easily guessed by others). If you forget
this password, you’ll need to reset the device to its default settings and go
through the device setup (as described in "Setting Up the Device" on
page 37).
Your administrator password must be 1–20 characters long.
•Wi-Fi network name (SSID)
This name is visible to other Wi-Fi-enabled devices, and is used to identify
your Wi-Fi network. The length of the Wi-Fi network name (SSID) depends on
other settings of the browser interface. (See the Help bubble that's displayed
when you move the cursor to the SSID input field.)
•Wi-Fi security
The default setting is WEP 64 Bit Open. To select another option, click More
options. See "Wi-Fi Security Options" on page 39.
•Wi-Fi password
The maximum length of this field is determined by the Wi-Fi security option
(the previous item). (See the Help bubble that's displayed when you move the
cursor to the Wi-Fi password field.)
If you'll be sharing your Internet connection with others, you'll have to give the
Wi-Fi password to others; don't use your banking or other important pass-
words. Also, don't use a password that's easily guessed by others.
From this window you can also enable the Password Reminder feature, which is
useful if you forget the Wi-Fi password. See "Wi-Fi Password Reminder" on
page 90.
Tip: Help information on each field appears (in a bubble) when you move the cursor into
the field.
You can display this window any time, by clicking Admin Setup ( ) in the browser
interface.
After you change the settings and click Submit, the device restarts and displays
updated information on its LCD. Follow the instructions on the LCD, and proceed
to "Your Device is Now Restarting" on page 40.
![](/img.php?id=1412542&img=bg27.png)
Installing and Setting Up the Device
Rev 1 Oct.10 39
Wi-Fi Security Options
If you click More options (after having clicked Set up my AirCard W802S, during the
device setup), a window with four Wi-Fi security options opens.
Note: All the devices used with the AirCard W802S personal hotspot must support the
selected security type.
Going from no security to stronger security, the options are:
•None
No security (no password is required to access the Wi-Fi network); not recom-
mended. Anyone may access your device and use your Internet connection
(you are responsible for payment for data usage).
•WEP-64 Bit
Lower security. Works with older and newer Wi-Fi devices. Recommended
only if any of your devices don't support WPA or WPA2.
•WPA-Personal
A strong security standard, supported by most Wi-Fi devices.
•WPA2-Personal
A stronger, newer security standard. Limited to newer Wi-Fi devices.
If the above options don't meet your requirements, click I don't see what I want....
Expanded Wi-Fi Security Options
If you display the Security panel of the Wi-Fi tab of the Advanced Settings window or
if you click I don't see what I want... (from the Wi-Fi Security Options window during
the device setup), a window with an expanded list of Wi-Fi security options opens.
Note: All the devices used with the AirCard W802S personal hotspot must support the
selected security type.
The options are:
•None
No security (no password is required to access the Wi-Fi network); not recom-
mended. Anyone may access your device and use your Internet connection
(you are responsible for payment for data usage).
•WEP-64 Bit - Shared
Lower security. Works with older and newer Wi-Fi devices. Recommended
only if any of your devices don't support WPA or WPA2.
Shared WEP uses the same key for encryption and authentication; some con-
sider shared WEP to be less secure than open WEP.
•WEP-128 Bit - Shared
Lower security. Works with older and newer Wi-Fi devices. Recommended
only if any of your devices don't support WPA or WPA2.
Shared WEP uses the same key for encryption and authentication; some con-
sider shared WEP to be less secure than open WEP.
![](/img.php?id=1412542&img=bg28.png)
AirCard W802S User Guide
40 2400092
•WEP-64 Bit - Open
Lower security. Works with older and newer Wi-Fi devices. Recommended
only if any of your devices don't support WPA or WPA2.
Open WEP uses the key for encryption, but not for authentication.
•WEP-128 Bit - Open
Lower security. Works with older and newer Wi-Fi devices. Recommended
only if any of your devices don't support WPA or WPA2.
Open WEP uses the key for encryption, but not for authentication.
•WPA-Personal - TKIP
A strong security standard, supported by most Wi-Fi devices.
•WPA-Personal - TKIP/AES
A strong security standard, supported by most Wi-Fi devices.
•WPA2-Personal - AES
A stronger, newer security standard. Limited to newer Wi-Fi devices.
•WPA2-Personal - TKIP/AES
A stronger, newer security standard. Limited to newer Wi-Fi devices.
•WPA/WPA2 Personal (recommended setting)
Wi-Fi devices that use either WPA or WPA2 can connect to the device. Sup-
ported by most Wi-Fi devices.
Your Device is Now Restarting
The "Your device is now restarting" window opens if you've clicked the Set up my
AirCard W802S option and then clicked Submit.
The changes take effect after the device restarts automatically.
It's recommended you write down the following information that's displayed in the
window:
•Wi-Fi network name
•Wi-Fi password
As described in the window,
1. Wait until the device LCD displays "Connect your computer to Wi-Fi Network".
2. Connect your computer to the Wi-Fi network, using the information you've
written down. (If you don't know how to do this, see "How Do I Connect to
Wi-Fi?" on page 112).
3. After the Wi-Fi connection was successfully established, click the Click here
text in the window.
![](/img.php?id=1412542&img=bg29.png)
Installing and Setting Up the Device
Rev 1 Oct.10 41
Activating and Using Your Network Service
Note: If you're able to connect to 3G, you are already set up to use <Carrier_Name>
service on the 3G network; no further action is needed. Proceed to "Using Your Device"
on page 43.
Before using your device, you must have a <Carrier_Name> wireless network
account set up. The process of setting up an account is called activation. When
the device starts up, it will detect whether the device has been configured with an
account ("preactivated"). If it has not, the activation process starts automatically.
In most cases, the activation process will be seamless, not requiring any action
from your part; in some cases, you won't even see any activation-related
messages displayed on the device LCD.
Initiating Activation of Your Device for 3G
In rare cases, the device LCD and the home page may indicate that activation is
required:
•The LCD displays "3G Activation failed".
•The home page displays the alert "3G Activation Required".
Note: You will still be able to connect to the Internet, when you have 4G coverage.
To activate your device for 3G:
1. In the Admin Login section (in the upper left area of the home page), enter the
administrator password (1–20 characters/numbers). (The default password is
"password".)
2. Click OK.
3. Click the alerts icon to display the alert window.
4. If more than one alert is available, use the and buttons (at the top of the
alert window) to browse to the "3G Activation Required" alert.
5. In the alert, click Activate now.
If the activation fails, contact <Carrier_Name>. See "Contacting Customer
Service" on page 111.
![](/img.php?id=1412542&img=bg2a.png)
AirCard W802S User Guide
42 2400092
![](/img.php?id=1412542&img=bg2b.png)
Rev 1 Oct.10 43
4
4: Using Your Device
Connecting Through USB
TRU-Install
TRU-Install is a Sierra Wireless feature that installs the necessary
drivers the first time you connect the device to your Windows or Mac
computer through the USB cable. (For details, see "Making a
Tethered Connection" below.) An installation CD is not required.
By default, TRU-Install is enabled.
To change the setting:
1. Ensure you're logged in to the home page.
2. Click Advanced settings > Device > Basic.
3. Select a value for TRU-Install.
Requirements for a USB Tethered Connection
Your device supports a direct connection through a USB cable to a
Windows or Mac computer. (This is commonly referred to as a
"tethered" connection.)
Making a Tethered Connection
Note: If you’ll be using USB for data transfer (and not just for charging the
device), you must install the device driver (see below). No installation CD is
required — the device supports the Sierra Wireless TRU-Install feature.
![](/img.php?id=1412542&img=bg2c.png)
AirCard W802S User Guide
44 2400092
Note: If you’re using Mac OS X 10.4.x, after you connect the device you may see a
warning message that your computer is running on UPS backup battery and that you
should perform a computer shutdown. You can continue with your work. To prevent this
message from being displayed, install the device driver (see "Mac", below).
Windows
1. Ensure the device is turned on.
2. Connect the device to your computer through the USB cable.
3. If the TRU-Install window is not displayed, in Windows Explorer browse to the
entry (under My Computer), then browse to the Win folder
and run Setup.exe.
— or —
If you’re running Windows Vista and the AutoPlay window opens, click Run
setup.exe.
4. In the TRU-Install window, click OK.
5. Go through the installation of the Sierra Wireless USB driver. (Follow the
instructions on the screen.)
— or —
1. Using Wi-Fi, connect to the device. See "How Do I Connect to Wi-Fi?" on
page 112.
2. Ensure you're logged in to the home page.
3. Click Advanced settings > Device > Basic.
4. In the TRU-Install section, click Windows, to download the .exe file to your
computer.
5. Run the .exe file, and go through the installation of the Sierra Wireless USB
driver. (Follow the instructions on the screen.)
Mac
1. Ensure the device is turned on.
2. Connect the device to your computer through the USB cable.
3. In the window that appears, double-click the .pkg file.
4. Go through the installation of the Sierra Wireless USB driver. (Follow the
instructions on the screen.)
5. When prompted for your password, enter your Mac password.
— or —
1. Using Wi-Fi, connect to the device. See "How Do I Connect to Wi-Fi?" on
page 112.
2. Ensure you're logged in to the home page.
3. Click Advanced settings > Device > Basic.
4. In the TRU-Install section, click Mac OS X, to download the file to your
computer.
![](/img.php?id=1412542&img=bg2d.png)
Using Your Device
Rev 1 Oct.10 45
5. If the "Welcome to the Sierra Wireless Driver Installer" window isn’t automati-
cally displayed, double-click the file that you’ve downloaded.
6. In the "Welcome to the Sierra Wireless Driver Installer" window, click Continue.
7. Follow the instructions on the screen.
Connecting the Device to Your Computer
1. Insert the larger (USB) end of the USB cable into your computer.
2. Insert the other (Micro B) end of the USB cable into the USB connector on the
side of the device.
Browser Interface Home Page
The home page is the entry page of the browser interface that lets you:
•Display status information for your device and your data connection.
•Launch and end a network connection
•Change the settings for your device and your data connections (if you're
logged in).
•Access additional resources (the user guide and the Important Information
document).
AB C
D
E
F
![](/img.php?id=1412542&img=bg2e.png)
AirCard W802S User Guide
46 2400092
Displaying the Home Page of the Device
Note: You can display the home page only when your device is turned on and you have
established a connection to it (through Wi-Fi or through the USB cable).
To display the home page, type one of the following in the address bar of your
Web browser:
•http://<Carrier_Name>
•SSID value (field in Advanced settings > Wi-Fi > Network and also in Advanced
settings > Router > LAN).
Note: If you're using the Google Chrome Web browser, after typing in the address bar,
press the Down Arrow key and then the Enter key. (If you press only the Enter key, a
Google search is started, using the information you typed in.)
If your Web browser displays an error message, see "Cannot Display the Home
Page" on page 122.
AWhen you click an icon or the text next to it, a window opens to the right (see the
screenshot on page 53). The window contains additional status information and,
if you're logged in, commonly-used configurable settings.
See "Vertical Row (of Icons and Text)" on page 52.
BUse this area to enter the administrator password and log in. When you're logged
in, you can change settings.
See "Logging On as an Administrator" on page 47.
CClicking one of these buttons displays a window or a menu. See "Buttons Along
the Top of the Home Page" on page 60.
DThis is the Virtual Device; it reflects the status of your AirCard W802S personal
hotspot. If you click the image, a movable Mini Window is opened.
See "Virtual Device" on page 47 and "Mini Window" on page 48.
EA handy way to turn the device off, especially if, for example, you're in an airplane
before takeoff, and the device is in your overhead bag.
Available only if you're logged in.
FDisconnects a connection, or connects (if currently there's no connection).
Available only if you're logged in.
![](/img.php?id=1412542&img=bg2f.png)
Using Your Device
Rev 1 Oct.10 47
Logging On as an Administrator
You don't need to log in to access and use the home page. However, when you're
logged in:
•Additional information appears in the window that appears when you click an
item on the left side of the home page. See "Vertical Row (of Icons and Text)"
on page 52.
•You can access the Advanced Settings window, where you can modify
additional settings.
•You can rerun the device setup, if required (Admin Setup []).
•You can install updates.
To log in:
1. Ensure that nobody else is already logged in — other people can use the
home page at the same time, but only one user can be logged in.
2. In the Admin Login section (in the upper left area of the home page), enter the
administrator password (1–20 characters/numbers). (The default password is
"password". It's recommended you change the password, if you haven't
already.)
3. Click OK.
After a certain time, you will be automatically logged off (timeout security feature),
unless you select Remember me (below the password field). For more information,
see "Automatic Login ("Remember Me")" on page 77.
Virtual Device
The right half of the home page contains an image of your device.
This is a "virtual device" — it reflects most of the icons and text displayed on the
real device.
![](/img.php?id=1412542&img=bg30.png)
AirCard W802S User Guide
48 2400092
Mini Window
If you click the virtual device on the home page, the Mini Window opens — an
image of the device in a separate Web browser window.
Similar to the virtual device, the Mini Window reflects most of the icons and text
displayed on the real device.
To save space on your monitor, you can close the home page and move the Mini
Window to the side of your monitor. Then you can use the window to keep an eye
on the status of your device and connection. (To reopen the home page, click the
Home link.)
If you're logged in, the window has a Connect or Disconnect button, and a Power Off
button.
Turning Your Device Off
From the Home page:
1. Ensure you're logged in to the home page.
2. Click Power Off (below the Virtual Device).
From the Mini Window:
1. Ensure you're logged in to the home page.
2. Click Power Off.
From the device:
1. Press and hold the power button for 2 seconds.
Note: You can turn the device on only by using the device power button.
![](/img.php?id=1412542&img=bg31.png)
Using Your Device
Rev 1 Oct.10 49
Alerts
Displaying Alerts
The alerts icon indicates whether there are any alerts (messages that require
your attention).
The icon is on the left side of the home page.
Click the icon to display the Alert window. If more than one alert is available:
•The higher priority alert opens.
•When you close an alert, the next alert opens.
•You can use the and buttons (at the top of the alert window) to view
other alerts.
The options and instructions shown in the alert window depend on the alert event.
Please read the instructions carefully. They may state, for example, that you have
to reconnect to Wi-Fi after an update is installed.
3G Activation Required
If only 3G coverage is available, you won't be able to connect to the Internet until
3G activation has been completed.
To activate 3G on your device:
1. Ensure you have 3G coverage.
2. In the Admin Login section (in the upper left area of the home page), enter the
administrator password (1–20 characters/numbers). (The default password is
"password".)
3. Click OK.
4. Click the alerts icon to display the alert window.
5. If more than one alert is available, use the and buttons (at the top of the
alert window) to browse to the "3G Activation Required" alert.
6. In the 3G Activation Required alert window, click Activate now. (Activation is
then performed over the network; no user interaction is required.)
•If activation is successful, "Activation complete!" is displayed. You can now
connect to the 3G network. If the connection is not established automatically,
click Connect on the home page or Mini Window.
•If activation was not successful, "Activation failed" is displayed. Retry the
activation. If it is not successful, prepare the following, and contact
<Carrier_Name>:
·Your billing information.
·ESN of the device (displayed on the packaging, on the device [under the
battery], and at Advanced settings > Device > About).
![](/img.php?id=1412542&img=bg32.png)
AirCard W802S User Guide
50 2400092
3G Network Update Available
The 3G Network Update Available alert appears if a PRL update or 3G profile
update is available for your device. The update may improve your 3G network
service.
Note: During installation of the update:
• DO NOT turn off or unplug the device.
• Your 3G connection won’t be available. (Your 4G connection won't be affected.)
To install the update:
1. Ensure you have 3G coverage.
2. In the Admin Login section (in the upper left area of the home page), enter the
administrator password (1–20 characters/numbers). (The default password is
"password".)
3. Click OK.
4. Click the alerts icon to display the alert window.
5. If more than one alert is available, use the and buttons (at the top of the
alert window) to browse to the "3G Activation Required" alert.
6. In the 3G Network Update Available alert window, click Update now.
SD Card Error
If you're having problems reading from the microSD card, or if the SD Card Error
alert window opens or the device LCD displays "SD Card error", try the following:
1. Remove and reinsert the microSD card.
2. If the card is still not working, try it in the microSD slot of another computer.
If it works in the other device, the card slot on your AirCard W802S personal
hotspot may have a problem.
If the card doesn’t work in the other computer, try one of the following:
· Use a different microSD card.
·Reformat your card.
Note: The formatting procedure erases all the data on the microSD card, after which the
files CANNOT be retrieved. To prevent the loss of important data, please check the
contents before you format the microSD card.
![](/img.php?id=1412542&img=bg33.png)
Using Your Device
Rev 1 Oct.10 51
Software Update Available
The update may improve performance and add or modify features.
Note: During installation of the update, your Internet and Wi-Fi connections won’t be
available.
When the installation is complete, you will need to reconnect to Wi-Fi.
To install the update:
1. Ensure your device is connected to the power adapter or computer, through
the USB cable.
Note: If you’ll be using USB for data transfer (and not just for charging the device), you
must install the device driver. See "Making a Tethered Connection" on page 43.
2. In the Admin Login section (in the upper left area of the home page), enter the
administrator password (1–20 characters/numbers). (The default password is
"password".)
3. Click OK.
4. Click the alerts icon to display the alert window.
5. If more than one alert is available, use the and buttons (at the top of the
alert window) to browse to the "3G Activation Required" alert.
6. In the Software Update Available alert window, click Update Options.
7. Read the information in the Software Installation Options window.
8. To install the updates, click Download and install now.
— or —
If you are not in a strong signal area, make a note of the URL displayed in the
window and click I’ll get the update later. At a later time, access the URL to
download the update to your computer, and then "Upgrade Firmware From a
File" on page 67.
9. When the installation is complete, reconnect to Wi-Fi. See "How Do I Connect
to Wi-Fi?" on page 112.
Your Network Connection
Launching Your Network Connection
After the device powers on and boots up, a connection to the 3G/4G network is
launched automatically, unless you've disabled Connect Automatically.
You will need to manually launch a connection if:
•The connection was not successful.
•You’ve disabled auto-connect.
• You’ve manually ended a connection (by clicking Disconnect).
![](/img.php?id=1412542&img=bg34.png)
AirCard W802S User Guide
52 2400092
To launch a connection:
•Click Connect on the Virtual Device on the home page (you must be logged
in).
— or —
Click Connect in the Mini Window (you must be logged in).
— or —
If the device LCD displays "Disconnected from 3G/4G network. Connect
now?", press the power button on the device.
Sharing Your Connection
For others to share your network connection:
1. Provide the Wi-Fi network name and password to them.
2. On their computer, users must connect to the Wi-Fi network of the AirCard
W802S personal hotspot. See "How Do I Connect to Wi-Fi?" on page 112.
Ending Your Network Connection
1. Ensure you're logged in to the home page.
2. Click Disconnect on the Virtual Device or in the Mini Window. See "Virtual
Device" on page 47 and "Mini Window" on page 48.
Note: The Wi-Fi connection is still available, so users can, for example, share files by
using a microSD card.
Vertical Row (of Icons and Text)
The left part of the home page has a vertical row of icons and text, starting with
the signal strength indicator .
![](/img.php?id=1412542&img=bg35.png)
Using Your Device
Rev 1 Oct.10 53
Most of these icons are also shown on the physical device and Virtual Device
(page 47). Hover the mouse over an icon; the corresponding icon on the Virtual
Device is highlighted.
If you click an icon or the text, a window opens with additional information, as
shown in the following screenshot.
If you're logged in, the window may also display configurable settings.
Tip: A more complete set of configurable settings is available in the Advanced Settings
window. See "Advanced Settings" on page 60.
Signal Information
Click the icon to display the Signal Quality window. The window displays:
•The active network: the network that is currently being used for your data
connection. For example: "3G (EVDO Rev A)".
•3G or 4G status:
·Connection status. For example: "Connected".
·Brief description of the signal strength. For example: "Good signal (60%)".
Icon Description
No signal
Very weak signal
... The number of bars reflects the signal strength: the more bars, the
stronger the signal.
Excellent signal
![](/img.php?id=1412542&img=bg36.png)
AirCard W802S User Guide
54 2400092
·Tables that show the coverage type, RSSI, and Ec/Io (for 3G) or CINR (for
4G).
RSSI reflects the signal strength of the network.
Ec/Io is a dimensionless ratio of the average power of a channel, typically
the pilot channel, to the total signal power.
CINR stands for Carrier to Interference-plus-Noise Ratio, and is a
measurement of signal effectiveness.
The first table also shows the type(s) of 3G service you have: 1X, 1xEV-DO,
or both. (To determine whether you have EV-DO Rev. 0 or Rev. A service, use
the text near the 3G icon; see "Mobile Broadband Information and Settings"
on page 54.)
See also "Improving Signal Strength" on page 114.
Mobile Broadband Information and Settings
The 3G or 4G icon indicates the service and connection state. Note that only one
icon is shown (the active network).
The text next to the icon displays the connection status, for example: "No
service", or "3G (EVDO Rev A)".
Click the icon or text to display the Mobile Broadband Information window. The
window displays:
•The active network: the network that is currently being used for your data
connection. For example: "4G" or "3G (EVDO Rev A)".
•3G and 4G status:
·Connection status. For example: "Connected".
·Brief description of the signal strength. For example: "Good signal (60%)".
•Connection Preferences (if you're logged in).
Configuring the 3G/4G Connection Preferences
The value determines which network(s) to connect to, and in what order:
•4G Preferred — Connection can be established to either 3G or 4G; if both are
available, 4G is used. This setting is recommended if your service provider
has no data limit for 4G, but does for 3G, or you want to take advantage of the
faster data transfer speeds of 4G.
•3G Preferred — Connection can be established to either 3G or 4G; if both are
available, 3G is used.
•4G Only — Connection can be established only to 4G.
•3G Only — Connection can be established only to 3G.
Icon Description
or You have no service. Try the suggestions in "Cannot Connect
to the 3G/4G Network" on page 123.
or You have service but are not connected.
or You have service and are connected.
![](/img.php?id=1412542&img=bg37.png)
Using Your Device
Rev 1 Oct.10 55
If you don’t have 4G coverage, you can save power by selecting "3G Only".
To automatically connect to the network upon loss of connection or when the
device powers on, select Connect Automatically.
3G Roaming Information and Settings
The roaming indicator shows whether you are roaming. The text near the icon
may indicate additional details.
Note: Roaming on 4G is not supported.
Click the icon to display the 3G Roaming Information window. The window
displays:
•Roaming status.
•Allow 3G roaming field (if you're logged in).
·If you select this field, you can roam and connect when outside of
<Carrier_Name> coverage, but additional charges may occur. (To roam
outside of North America, you must also select Allow international access.)
·If you do not select this field, you can connect only when you're inside the
<Carrier_Name> coverage area.
•Allow international access field (if you're logged in, and subject to feature avail-
ability) — allows roaming outside of North America.
·If this field is displayed but not available, select Allow 3G roaming.
Alert Information
The alerts icon indicates whether there are any alerts (situations that require your
attention).
Note: To view alert information, you must be logged in. New alerts are checked upon
device power-up. That is, if an event occurs, you won't be notified until the device is
restarted.
The text next to the icon indicates the number of alerts.
Click the icon or text to display the Alert window.
Icon Description
Not roaming
Roaming
[flashing] Enhanced roaming indicator
Icon Description
No alerts are available.
One or more alert is available.
![](/img.php?id=1412542&img=bg38.png)
AirCard W802S User Guide
56 2400092
For more information, see "Alerts" on page 49.
Wi-Fi Users Information and Settings
The Wi-Fi users icon shows how many Wi-Fi users are connected to the device.
Click the icon to display the Connected Users window.
Connected User Information
When you're logged in, the Connected Users window shows a table with
information on computers currently connected to the device.
A row may optionally show one or both of these icons:
• — The user of this computer is logged in as administrator.
• — This computer is connected to the device through the USB cable.
MAC Address — Each wireless device has a unique MAC address (assigned by its
manufacturer). On a Windows PC, the MAC address is called the "physical
address"; on a Mac, it is called the "Ethernet ID". See "Finding the MAC Address"
on page 117.
Block — Used to block the computer's access to the device. You might want to do
this if:
•You don't recognize a listed computer.
•You have lots of data to transfer (you want to be the sole user of the
bandwidth).
•You're approaching the data limit on your account.
Note: You cannot block the administrator. (The row for the administrator has the
icon).
Max Wi-Fi users — Limits the number of Wi-Fi users that can connect to the
device. A smaller number improves performance and security.
Disable Wi-Fi when connected via USB — Turns off the Wi-Fi of the device when
connected to a computer through the USB cable. Only this computer will be able
to use the device.
Icon Description
No Wi-Fi users are connected. (One user is connected via USB).
One user is connected via Wi-Fi.
The number indicates how many Wi-Fi users are connected.
![](/img.php?id=1412542&img=bg39.png)
Using Your Device
Rev 1 Oct.10 57
Battery Information and Settings
The battery icon indicates the state of the battery of the device.
The text next to the icon displays additional information, for example, the charging
status (% remaining or % complete).
Tip: You can also check the battery icon from the Home page, Mini Window, and Device
LCD.
Click the icon to display the Battery Information and Settings window.
When you're logged in, you can set the behavior for when the device is:
•Battery or USB powered. Choose one of the following:
·Better battery life — At the cost of shorter Wi-Fi range.
·Longer Wi-Fi range — At the cost of shorter battery life.
•AC powered. Choose one of the following:
·Longer Wi-Fi range
·Shorter Wi-Fi range — You have a designated wireless area and you need to
minimize the effect of your network on other networks in the vicinity.
Standby (Low Power) Mode
When the device is in standby (low power) mode, the 3G/4G modem radios, the
Wi-Fi radio, and the LCD are off, and the power button is flashing.
When you're logged in, you can set how soon the device goes into standby mode
when no Wi-Fi users are connected to it (Standby Timer).
You can specify settings for battery power and AC power.
Note: This setting has no effect when the device is connected to a computer through the
USB cable.
Icon Description
Battery level is critical. Charge the device immediately. See "Charging the
Device" on page 31.
No battery; connected to an electrical outlet (through the power adapter).
Connected to USB. Battery is either charging, or is not inserted.
Charging through the power adapter.
Battery is low. Charge the device. See "Charging the Device" on page 31.
... The more bars are shown, the more the battery is charged.
Battery is charged.
![](/img.php?id=1412542&img=bg3a.png)
AirCard W802S User Guide
58 2400092
To exit standby mode:
•Connect the device to the power adapter or computer, through the USB
cable.
— or —
Press the power button .
Internet Connection Information
Note: Data usage amounts are approximate and should not be used for billing purposes.
For accurate data usage amounts, check with <Carrier_Name>.
Click the data icon to display the Internet Connection Information window.
The window displays:
•Data statistics for the current connection session:
·Data sent
·Data received
·Total transferred
·Session duration
•The WWAN IP address of the device — the external IP address of the
modem (3G or 4G) — that is, the IP address of the modem as seen from the
Internet.
Viewing and Configuring Detailed Internet Connection Information
When you're logged in, the Internet Connection Information window displays a
table showing data use:
•In the currently billing cycle. These numbers get automatically reset to 0 on
the day selected in the Starts on day list.
•Over the lifetime of the device.
•By network (3G/4G), and by sent/received/total.
From this window you can:
•Reset the data usage figures for the current billing cycle. (Click Reset.)
•Change the start day of the billing cycle (in the Starts on day list).
microSD Card Information and Settings
The text next to the icon indicates whether the card is:
•Enabled
•Detected
•Accessible by all ("shared") or only the administrator
•Accessible with or without a password (security)
Click the icon to display the SD Card Information and Settings window. The
window displays:
•The card status (see the above list)
•Storage capacity of the card, and space available
![](/img.php?id=1412542&img=bg3b.png)
Using Your Device
Rev 1 Oct.10 59
When you're logged in, you can:
•Enable or disable the microSD card slot. See "Enabling the microSD Card
Slot" on page 62.
•Set up access to the card. See "Setting Up Access to the microSD Card" on
page 62.
Sounds Information and Settings
The sounds icon ( ) shows whether the device speaker is on.
Click the icon to display the Sounds window. The window displays:
•Status of the device speaker (on or off).
•If you're logged in: check boxes to enable or disable sounds for the following
events:
·Internet connected
·Internet disconnected
·Low battery — Useful as a reminder to charge the device.
·System alerts — When you hear the device beep, you can then use the
device LCD or the Alerts window to get information about the alert. See
"Alert Information" on page 55.
Note: System alerts include several types of events, for example:
• Critical battery
• Critical temperature
• Software update available
• Network update available
• Routing hardware settings reset
• Device startup failure
·Wi-Fi user has joined — Useful, for example, to detect an unwelcome Wi-Fi
user if you're the only one using the device.
·Wi-Fi user has left
·Last user has left — When you hear the device beep, you can turn off the
device, if nobody will be using it for awhile.
Tip: You can also disable all sounds through the mute switch on the device. See "Mute
Switch" on page 36.
If you've enabled the sounds through the home page, but there are no sounds when an
event occurs, check the position of the Mute switch.
Icon Description
The device speaker is on.
The device speaker is off.
![](/img.php?id=1412542&img=bg3c.png)
AirCard W802S User Guide
60 2400092
Home Page Buttons
Buttons Along the Top of the Home Page
The top horizontal part of the home page has the following areas and buttons:
•Admin Login. See "Logging On as an Administrator" on page 47.
•Admin Setup — Rerun the device setup, for example, after you've reset the
software to default settings. See "Welcome to Your Device Window - Select
an Option" on page 110.
•Advanced settings. See "Advanced Settings" on page 60.
•Support. See "Support Button" on page 60.
•Feedback — Send your comments on the device. See "Feedback" on page 61.
•Help — Open the Help system, display the important information booklet, or
download the user guide.
Admin Setup Button
This button displays a window where you can change the administrator password,
Wi-Fi network name (SSID), Wi-Fi security type, and Wi-Fi password.
For more information, see "Welcome to Your Device Window - Select an Option"
on page 110.
Advanced Settings
From the Advanced Settings window you can configure all the settings of the
device and the browser interface.
The Advanced Settings window has the following tabs; each tab has several
panels.
•Device tab. See "Device Tab" on page 78.
•WAN tab. See "WAN Tab" on page 82.
•Wi-Fi tab. See "Wi-Fi Tab" on page 84.
•Router tab. See "Configuring the Router Tab" on page 95.
For help on a tab, click Help ( ). For most fields and buttons, contextual (field-
level) Help appears to the right of the window, when you move the cursor over the
item. For more information, see "Contextual Help in the Advanced Settings
Window" on page 111.
Accessing the Advanced Settings Window
1. Ensure you're logged in to the home page.
2. Click Advanced settings ().
Support Button
The Support button opens, in a new Web browser window (or tab), the online
support site for your device.
Note: This button is available only when you're connected to the Internet.
![](/img.php?id=1412542&img=bg3d.png)
Using Your Device
Rev 1 Oct.10 61
Feedback
The Feedback button opens, in a new Web browser window (or tab), the online
feedback site for your device.
Note: This button is available only when you're connected to the Internet.
Help Button
This button displays a menu with options to:
•Display the online Help.
•Download the user guide.
•View the important information booklet. This booklet contains warranty and
other information.
Buttons Below the Virtual Device
Note: The buttons appear only when you're logged in.
Connect/Disconnect Button
This button disconnects a connection, or connects (if currently there's no
connection).
Power Off Button
This button turns the device off.
Note: You can turn the device on by using the device power button.
Using the microSD Card
Before Using the microSD Card Slot
1. Enable the slot. See "Enabling the microSD Card Slot" on page 62.
2. Set up access to the slot. See "Setting Up Access to the microSD Card" on
page 62.
3. [OPTIONAL]: Rename the microSD Shared Folder Name. See "microSD Shared
Folder Name" on page 62.
4. Inform others how they can access the card. See "Accessing the microSD
Card" on page 64.
![](/img.php?id=1412542&img=bg3e.png)
AirCard W802S User Guide
62 2400092
Enabling the microSD Card Slot
Before computers can recognize the microSD card, you must enable the
microSD slot on the device.
1. Ensure you're logged in to the home page.
2. In the SD Card Information and Settings window, select Enable SD Card. (See
"microSD Card Information and Settings" on page 58.)
— or —
From Advanced settings > Device > microSD card, in the SD-Card Slot section
select Enable.
Setting Up Access to the microSD Card
If you've enabled access to the microSD card, you must also specify whether a
username and password are required to access the card.
1. Ensure you're logged in to the home page.
2. In the SD Card Information and Settings window or from Advanced settings
> Device > microSD card, under Username and Password Security, select one of
the values:
·To have no security, select None.
Anyone can use the card; no username or password is required.
·To allow only the administrator to use the card, select Administrator Only.
When prompted for the username (when you try to use the card), enter
"admin". For the password, enter the home page login password.
·To allow non-administrators to use the card, select Administrator + Guest.
3. If you've selected Administrator + Guest:
a. [OPTIONAL]: Change the Set Guest Username and Set Guest Password
fields (up to 20 characters each; spaces are allowed).
b. Give the guest username and password to people whom you want to
allow access to the card.
microSD Shared Folder Name
You can optionally change the name of the folder that the microSD card shows up
as (in the file browser program); the default folder name is "shared".
1. Ensure you're logged in to the home page.
2. Click Advanced settings > Device > MicroSD card.
3. In the MicroSD Shared Folder Name field, type the new name.
You can use up to 32 letters, numbers, and spaces in any combination.
For information on how this folder name is used, see "Accessing the microSD
Card" on page 64.
![](/img.php?id=1412542&img=bg3f.png)
Using Your Device
Rev 1 Oct.10 63
Inserting a microSD Card
To insert the microSD card:
1. Gently flip open the tab labelled "microSD" on the side of the device.
2. Gently insert the microSD card (label facing up) into the slot on the side of the
device, until the microSD card clicks into place.
Note: If your microSD card has not been formatted, or is in a format that your computer
does not recognize, you may be prompted to format the microSD card. The formatting
procedure erases all the data on the microSD card, after which the files CANNOT be
retrieved. To prevent the loss of important data, please check the contents before you
format the microSD card.
3. Check the status of the microSD card. See "microSD Card Information and
Settings" on page 58.
Removing a microSD Card
1. Ensure you and other users have completed any file transfers.
2. Gently flip open the tab labelled "microSD" on the side of the device.
3. Using your fingernail or a thin blunt object, gently press the microSD card in
and then release; it should partially pop out of its slot, as shown in the
drawing above.
4. Remove the microSD card and store it in a safe place.
5. Close the tab over the microSD slot of the device.
![](/img.php?id=1412542&img=bg40.png)
AirCard W802S User Guide
64 2400092
Accessing the microSD Card
If the microSD slot is enabled, an inserted card appears in your file browser as a
shared network drive.
The way to access the card varies, depending on your operating system.
Note: In the information that follows, <Hostname> is the value of the Hostname field (in
Advanced settings > Wi-Fi > Network and also in Advanced settings > Router > LAN).
Windows
1. In Windows Explorer or Internet Explorer, type one of the following:
·\\<Carrier_Name>\
·\\<Router IP address>\ (field in Advanced settings > Router > LAN)
For example: \\192.168.0.1\
·\\<Hostname>\
For example: \\MyDeviceName\
— or —
From the Windows start menu, click start > Run, and then type one of the fol-
lowing:
·\\<Carrier_Name>\
·\\<Hostname>\
2. Double-click the shared folder.
Mac
1. In Finder, select Go > Connect to Server.
2. Type one of the following:
·smb://<Carrier_Name>/
·smb://<Router IP address>/
·smb://<Hostname>/
3. When prompted, select the shared drive as the folder to mount.
Linux
1. Open the run menu (Alt+F2) or a file browser, and type one of the following:
·smb://<Carrier_Name>/
·smb://<Router IP address>/
·smb://<Hostname>/
2. Double-click the shared folder.
Other operating systems
Please see the user documentation for your operating system or computer.
If security has been enabled for the microSD card, you will be prompted to enter
the username and password for the microSD card. (See "Setting Up Access to
the microSD Card" on page 62).
![](/img.php?id=1412542&img=bg41.png)
Using Your Device
Rev 1 Oct.10 65
Updates
Note: If a software update, 3G network update, or 3G profile update is available, the
device LCD displays a message, and an alert is available from the home page. See
"Software Update Available" on page 51 and "3G Network Update Available" on
page 50.
The update may improve performance and add or modify features. The updates
may include the following:
•Device firmware
•3G network update
•The browser interface
•Help files
•Other files
You can:
•Manually check for updates. See "Manually Checking for Updates" on
page 66.
•Set the browser interface to automatically check for updates. See the next
section.
Automatically Checking for Updates
To specify how often the browser interface checks for updates:
1. Log in to the home page.
2. Click Advanced settings ().
3. Click Device > Basic.
4. In the Check for Updates list, click an option.
Note: If Check for Updates is not available, your device supports the Guaranteed Update
feature, which automatically checks for updates, at a pre-determined frequency. This
feature requires 4G coverage.
Tip: When updates are available, an alert is shown in the browser interface. See "Alert
Information" on page 55.
![](/img.php?id=1412542&img=bg42.png)
AirCard W802S User Guide
66 2400092
Manually Checking for Updates
Note: During installation of the update:
• DO NOT turn off or unplug the device.
• Your Wi-Fi and Internet connections won’t be available.
When the installation is complete, you will need to reconnect to Wi-Fi. (See "How Do
I Connect to Wi-Fi?" on page 112).
Checking for updates
1. Log in to the home page.
2. Ensure you're connected to 3G/4G.
3. Click Advanced settings().
4. Click Device > Basic.
5. Click Check for updates now. (The message next to the button indicates
whether updates are available.)
Installing the updates
If updates are available, after you've manually checked for updates:
1. Ensure your device is connected to the power adapter or computer, through
the USB cable.
Note: If you’ll be using USB for data transfer (and not just for charging the device), you
must install the device driver. See "Making a Tethered Connection" on page 43.
2. Click Update options.
3. Read the information in the Software Installation Options window.
4. To install the updates, click Download and install now.
— or —
If you are not in a strong signal area, make a note of the URL displayed in the
window and click I’ll get the update later. At a later time, access the URL to
download the update to your computer, and then follow the steps in "Upgrade
Firmware From a File" on page 67.
5. When the installation is complete, reconnect to Wi-Fi. See "How Do I Connect
to Wi-Fi?" on page 112.
![](/img.php?id=1412542&img=bg43.png)
Using Your Device
Rev 1 Oct.10 67
Upgrade Firmware From a File
Use this option when you have an updated firmware file that you've, for example,
downloaded from the <Carrier_Name> or Sierra Wireless website.
Note: During installation of the update:
• DO NOT turn off or unplug the device.
• Your Wi-Fi and Internet connections won’t be available.
When the installation is complete, you will need to reconnect to Wi-Fi. (See "How Do
I Connect to Wi-Fi?" on page 112).
To upgrade the device firmware from a file:
1. Log in to the home page.
2. Ensure Disable Wi-Fi when connected via USB is selected. See "Disabling Wi-Fi
When Connected Through USB" on page 93.
3. Ensure your device is connected to the power adapter or computer, through
the USB cable.
4. Click Advanced settings ().
5. If you want to later confirm that the upgrade was successful, write down the
current version information (shown in Device > About):
·Software version
·Firmware version (in the 3G section)
·Firmware version (in the 4G section)
6. Click Device > Basic.
7. [OPTIONAL]: Save the current configuration (recommended).
a. Click Export.
b. Save the file. Note the filename and path.
8. Click Browse next to the Update Firmware From File field, and click the firmware
file to upload to the device.
9. Click Update.
Please wait while the upgrade occurs; this may take several minutes. The
device LCD shows the upgrade status. The device will restart (possibly sev-
eral times).
Once the upgrade is complete, the LCD device shows the usual icons and text
(for example, the device name).
10. Compare the current version information (in Device > About) to the values you
wrote down in step 5 to confirm that the upgrade was successful.
11. If you've saved the current configuration, reload it.
a. Click Browse next to the Import Router Settings field, and click the file you've
saved.
b. Click Import.
12. Reconnect to Wi-Fi. See "How Do I Connect to Wi-Fi?" on page 112.
![](/img.php?id=1412542&img=bg44.png)
AirCard W802S User Guide
68 2400092
Viewing Device Information
1. Log in to the home page.
2. Click Advanced settings ().
3. Click Device > About.
Note: 4G information is not available if WAN mode is "3G only". (WAN mode is in
Advanced settings > WAN > Setup.)
The following information is displayed:
•Model Number
•Manufacturer
•Software Version.
Firmware version for the routing hardware component of the device.
•Activation Status.
3G activated, or not activated.
•Activation Date.
Date that the 3G modem was first activated.
•Network Operator.
The carrier that your device was activated for.
•Wi-Fi Firmware Version
•Router PRI Version.
PRI version for the routing hardware component of the device. The PRI (Prod-
uct Release Instructions) is a file that contains the settings used to configure
wireless products for a particular service provider, customer, or purpose.
•ESN or MEID (3G).
The ESN (Electronic Serial Number) is the unique first-generation serial num-
ber assigned to the 3G component of the device.
The MEID (Mobile Equipment Identifier) is the unique second-generation
serial number assigned to the 3G component of the device.
•PRI Version.
PRI version of the 3G component of the device. The PRI (Product Release
Instructions) is a file that contains the settings used to configure wireless
products for a particular service provider, customer, or purpose.
•MSID (Mobile Station ID)
The MSID is also known as IMSI (International Mobile Station Identity) — an
identifier of a device on the 3G network.
•PRL Version.
The PRL (Preferred Roaming List) is an account configuration item set by
your service provider. It controls the radio channels and network carrier used
by the 3G modem. An updated PRL may improve your 3G network service.
•Firmware Version.
Firmware version of the 3G component of the device.
![](/img.php?id=1412542&img=bg45.png)
Using Your Device
Rev 1 Oct.10 69
•MAC Address.
MAC address of the 4G module. Each wireless device has a unique MAC
address (assigned by its manufacturer).
•Firmware Version.
Firmware version of the 4G component of the device.
The window also has buttons to:
•Save the information to a text file.
•Reset the 3G/4G configuration of the device to default settings. See
"Resetting the 3G/4G Configuration to Default Settings" on page 94.
Reset Button
The reset button is inside the hole located below and to the right of the battery
compartment as shown below.
For information on using this button, see "Restarting the Device" on page 70 and
"Resetting the Software to Default Settings (Through the Reset Button)" on
page 105.
Reset button
![](/img.php?id=1412542&img=bg46.png)
AirCard W802S User Guide
70 2400092
Restarting the Device
Tip: Alternatively, you may be able to restart the device by pressing and holding the power
button on the device for three to four seconds.
If the device or the home page seems to stop responding, you can reset (restart)
the device:
1. Remove the battery compartment cover.
2. Find the small hole below and to the right of the battery compartment. The
reset button is inside this hole.
3. Insert a thin object (for example, the end of a paper clip) into the hole, and
lightly press on the bottom of the hole for about a second).
Reset button
![](/img.php?id=1412542&img=bg47.png)
Using Your Device
Rev 1 Oct.10 71
4. Replace the battery compartment cover.
![](/img.php?id=1412542&img=bg48.png)
AirCard W802S User Guide
72 2400092
![](/img.php?id=1412542&img=bg49.png)
Rev 1 Oct.10 73
5
5: Settings
Power Settings
Battery and USB Power Settings
You can specify the settings for battery and USB power:
•Better battery life — At the cost of a shorter Wi-Fi range.
•Longer Wi-Fi range — At the cost of a shorter battery life.
To choose an option:
1. Ensure you're logged in to the home page.
2. Click the battery icon . The Battery Information and
Settings window opens.
— or —
Click Advanced settings > Wi-Fi > Network.
3. Select an option in the Battery or USB Powered section.
AC Power Settings
You can specify the settings for AC power:
•Longer Wi-Fi range
•Shorter Wi-Fi range
To choose an option:
1. Ensure you're logged in to the home page.
2. Click the battery icon . The Battery Information and
Settings window opens.
— or —
Click Advanced settings > Wi-Fi > Network.
3. Select an option in the AC Powered section.
Configuring the LCD
Turning the LCD On or Off
1. Log in to the home page.
2. Click Advanced settings ().
3. Click Device > Display.
![](/img.php?id=1412542&img=bg4a.png)
AirCard W802S User Guide
74 2400092
4. Set the LCD Backlight field to On or Off. (Off helps prolong the battery life, but
you can't check the LCD for status icons and messages.)
Setting the LCD Timeout
Tip: Alternatively, you can permanently turn off the LCD, in which case it will never
become lit and will not display text and icons. See "Turning the LCD On or Off" on
page 73.
To set the amount of time, after which the LCD of the device temporarily turns off:
1. Ensure you're logged in to the home page.
2. Click Advanced settings > Device > Display.
3. Ensure LCD Backlight is set to On.
4. In the Turn Off Backlight list, click a value. (A smaller value helps prolong the
battery life.)
Note: The LCD turns on if an important system event occurs.
Setting the LCD Brightness
1. Ensure you're logged in to the home page.
2. Click Advanced settings > Device > Display.
3. Ensure LCD Backlight is set to On.
4. Select a value for On Battery/USB Power. (A lower brightness prolongs the
battery life.)
5. Select a value for On AC Power.
Enabling and Disabling the LED
The power button on the device acts as an LED/status indicator, and may or
may not be lit. For more information, see "Using the Power Button to Determine
the Device State" on page 34.
To enable or disable the lighting of the power button :
1. Log in to the home page.
2. Click Advanced settings ().
3. Click Device > Display.
4. Set the Power Button LED field to On or Off.
![](/img.php?id=1412542&img=bg4b.png)
Settings
Rev 1 Oct.10 75
Sounds
Enabling and Disabling Sounds
You can enable or disable sounds of the device through:
•The mute switch on the device (disables all sounds). See "Mute Switch" on
page 36.
•The browser interface (selectively disables sounds). See "Sounds Information
and Settings" on page 59 and "Enabling and Disabling Sounds for Specific
Events" on page 75.
Enabling and Disabling Sounds for Specific Events
1. Log in to the home page.
2. Click Advanced settings ().
3. Click Device > Sounds.
4. Next to each of the event types, select Enable or Disable.
Sounds for the following events can be individually enabled or disabled:
•Low Battery
Useful as a reminder to charge the device. In the Alert When list, you can
select a battery level to trigger the alert.
•System Alerts
When you hear the device beep, use the device LCD or the Alerts window to
get information about the alert. See "Alert Information" on page 55.
Note: System alerts include several types of events, for example:
• Critical battery
• Critical temperature
• Software update available
• Network update available
• Routing hardware settings reset
• Device startup failure
•Internet Connected
•Internet Disconnected
•Wi-Fi User Has Joined
Useful, for example, if you're the only one using the device, to detect an
intruder.
•Wi-Fi User Has Left
•Last User Has Left
You can turn off the device if nobody will be using it for a while.
![](/img.php?id=1412542&img=bg4c.png)
AirCard W802S User Guide
76 2400092
Low Battery Alert
You can set an alert to sound when the battery level is low.
Setting the Alert From the Home Page
1. Ensure you're logged in to the home page.
2. Click the Sounds icon ( ).
3. In the Sounds window, select Low battery.
Setting the Alert From the Advanced Settings Window
1. Log in to the home page.
2. Click Advanced settings ().
3. Click Device > Sounds.
4. For the Low Battery field, select Enable.
5. In the Alert When list, click a battery level to trigger the alert.
Critical Battery Level Alert
You can enable an alert to sound when the battery level is critical (that is,
dangerously low).
1. Log in to the home page.
2. Click Advanced settings ().
3. Click Device > Sounds.
4. For the System Alerts field, select Enable.
Note: System alerts include several types of events, for example:
• Critical battery
• Critical temperature
• Software update available
• Network update available
• Routing hardware settings reset
• Device startup failure
![](/img.php?id=1412542&img=bg4d.png)
Settings
Rev 1 Oct.10 77
Login Settings
Changing the Administrator Password
Note: If you forget the Admin login password, you’ll need to reset the device to its default
settings and go through the device setup. See "What Do I Do if I Forgot the Adminis-
trator Password?" on page 113.
1. Log in to the home page.
2. Click Advanced settings ().
3. Click Device > Basic.
4. In the Admin Password field, type the new password (1–20 characters/
numbers).
Automatic Login ("Remember Me")
If you enable automatic login:
•Anyone who uses the computer will automatically be logged in to the home
page (as long as no one else has already logged in from another computer);
entering the administrator password is not required.
•The timeout security feature is disabled — you will never be automatically
logged off.
To enable automatic login:
1. From the computer that you want to enable automatic login, log in to the
home page.
2. In the login area, select the Remember me check box.
You can repeat the above steps on other computers; however, since only one
administrator can be logged in at a time, only the first person to display the home
page will be logged in.
Viewing Computers That Are Set to Automatically Log In as Administrator
1. Log in to the home page.
2. Click Advanced settings ().
3. Click Device > Basic.
4. Next to Remember Me Client List, click show list.
Disabling Automatic Login For a Specific Computer
1. Log in to the home page.
2. Click Advanced settings ().
3. Click Device > Basic.
4. Next to Remember Me Client List, click show list.
![](/img.php?id=1412542&img=bg4e.png)
AirCard W802S User Guide
78 2400092
5. In the row for the computer that you want to disable automatic login, click
Remove.
Advanced Settings
From the Advanced Settings window you can configure all the settings of the
device and the browser interface.
The Advanced Settings window has the following tabs; each tab has several
panels.
•Device tab. See "Device Tab" on page 78.
•WAN tab. See "WAN Tab" on page 82.
•Wi-Fi tab. See "Wi-Fi Tab" on page 84.
•Router tab. See "Configuring the Router Tab" on page 95.
For help on a tab, click Help ( ). For most fields and buttons, contextual (field-
level) Help appears to the right of the window, when you move the cursor over the
item. For more information, see "Contextual Help in the Advanced Settings
Window" on page 111.
Accessing the Advanced Settings Window
1. Ensure you're logged in to the home page.
2. Click Advanced settings ().
Device Tab
Basic Panel
1. Log in to the home page.
2. Click Advanced settings ().
3. Click Device > Basic.
From this window, you can view and adjust settings, or perform the following
actions:
•Admin Password — Login password. See "Changing the Administrator
Password" on page 77.
•Remember Me Client List — View a list of computers that are set to automati-
cally log in. See "Automatic Login ("Remember Me")" on page 77.
•Help for Advanced Settings — Enable or disable contextual Help in the
Advanced Settings window. See "Contextual Help in the Advanced Settings
Window" on page 111.
•Import Router Settings — Import configuration settings. See "Importing
Settings" on page 107.
• Export Router Settings — Export configuration settings. See "Exporting
Settings" on page 107.
•Update Firmware From File. See "Upgrade Firmware From a File" on page 67.
![](/img.php?id=1412542&img=bg4f.png)
Settings
Rev 1 Oct.10 79
•Standby Timer on Battery or USB and On AC Power — Enable standby (low
power) mode. See "Standby (Low Power) Mode" on page 57.
•Check for Updates automatically and Check for updates now. See "Automatically
Checking for Updates" on page 65 and "Manually Checking for Updates" on
page 66.
•TRU-Install — Installs the necessary drivers the first time you connect the
AirCard W802S personal hotspot to your Windows or Mac computer. For
information on this feature, see "TRU-Install" on page 43.
•Windows and Mac OS X — Download the Windows or Mac driver (if you're
using USB for data transfer). See "Making a Tethered Connection" on
page 43.
Display Panel
From the Display panel of the Device tab, you can configure settings for the device
LCD.
1. Log in to the home page.
2. Click Advanced settings ().
3. Click Device > Display.
From this window, you can view or adjust these settings:
•Lighting of the power button on the device (Power Button LED). See
"Enabling and Disabling the LED" on page 74.
•Turn the LCD on or off (LCD Backlight). See "Turning the LCD On or Off" on
page 73.
•LCD timeout — how soon the LCD goes dormant (Turn Off Backlight). See
"Setting the LCD Timeout" on page 74.
•Brightness of the LCD (Backlight Settings). See "Setting the LCD Brightness"
on page 74.
microSD Card Panel
1. Log in to the home page.
2. Click Advanced settings ().
3. Click Device > microSD Card.
From this window, you can view and adjust settings, or perform the following
actions:
•Status of the microSD card slot.
•Enable the microSD card slot. See "Enabling the microSD Card Slot" on
page 62.
•Folder name for the shared micro SD card. See "microSD Shared Folder
Name" on page 62.
•Set up access to the microSD Card. See "Setting Up Access to the microSD
Card" on page 62.
![](/img.php?id=1412542&img=bg50.png)
AirCard W802S User Guide
80 2400092
Sounds Panel
From the Sounds panel of the Device tab, you can enable or disable sounds for
specific types of events.
1. Log in to the home page.
2. Click Advanced settings ().
3. Click Device > Sounds.
4. Next to each of the event types, select Enable or Disable.
Sounds for the following events can be individually enabled or disabled:
•Low Battery
Useful as a reminder to charge the device. In the Alert When list, you can
select a battery level to trigger the alert.
•System Alerts
When you hear the device beep, use the device LCD or the Alerts window to
get information about the alert. See "Alert Information" on page 55.
Note: System alerts include several types of events, for example:
• Critical battery
• Critical temperature
• Software update available
• Network update available
• Routing hardware settings reset
• Device startup failure
•Internet Connected
•Internet Disconnected
•Wi-Fi User Has Joined
Useful, for example, if you're the only one using the device, to detect an
intruder.
•Wi-Fi User Has Left
•Last User Has Left
You can turn off the device if nobody will be using it for a while.
About Panel
1. Log in to the home page.
2. Click Advanced settings ().
3. Click Device > About.
Note: 4G information is not available if WAN mode is "3G only". (WAN mode is in
Advanced settings > WAN > Setup.)
![](/img.php?id=1412542&img=bg51.png)
Settings
Rev 1 Oct.10 81
The following information is displayed:
•Model Number
•Manufacturer
•Software Version.
Firmware version for the routing hardware component of the device.
•Activation Status.
3G activated, or not activated.
•Activation Date.
Date that the 3G modem was first activated.
•Network Operator.
The carrier that your device was activated for.
•Wi-Fi Firmware Version
•Router PRI Version.
PRI version for the routing hardware component of the device. The PRI (Prod-
uct Release Instructions) is a file that contains the settings used to configure
wireless products for a particular service provider, customer, or purpose.
•ESN or MEID (3G).
The ESN (Electronic Serial Number) is the unique first-generation serial num-
ber assigned to the 3G component of the device.
The MEID (Mobile Equipment Identifier) is the unique second-generation
serial number assigned to the 3G component of the device.
•PRI Version.
PRI version of the 3G component of the device. The PRI (Product Release
Instructions) is a file that contains the settings used to configure wireless
products for a particular service provider, customer, or purpose.
•MSID (Mobile Station ID)
The MSID is also known as IMSI (International Mobile Station Identity) — an
identifier of a device on the 3G network.
•PRL Version.
The PRL (Preferred Roaming List) is an account configuration item set by
your service provider. It controls the radio channels and network carrier used
by the 3G modem. An updated PRL may improve your 3G network service.
•Firmware Version.
Firmware version of the 3G component of the device.
•MAC Address.
MAC address of the 4G module. Each wireless device has a unique MAC
address (assigned by its manufacturer).
•Firmware Version.
Firmware version of the 4G component of the device.
The window also has buttons to:
•Save the information to a text file.
•Reset the 3G/4G configuration of the device to default settings. See
"Resetting the 3G/4G Configuration to Default Settings" on page 94.
![](/img.php?id=1412542&img=bg52.png)
AirCard W802S User Guide
82 2400092
Log Panel
1. Log in to the home page.
2. Click Advanced settings ().
3. Click Device > Log.
From this window, you can:
•Enable logging of system events. See "Enabling and Disabling Logging of
System Events" on page 109.
•Enable logging of connects/disconnects. See "Enabling and Disabling
Logging of Connect/Disconnects" on page 108.
•Export logs. See "Exporting System Events" on page 109 and "Exporting the
Connection History" on page 108.
•Clear logs. See "Clearing the System Events Log" on page 109 and "Clearing
the Connection History" on page 108.
•Set the method used for time acquisition. See "Setting the Method Used for
Time Acquisition" on page 109.
WAN Tab
See also "3G Panel" on page 94.
Setup Panel
1. Log in to the home page.
2. Click Advanced settings ().
3. Click WAN > Setup.
From this window, you can view and adjust settings, or perform the following
actions:
•Active Network — Network that is currently being used for your data
connection: 3G, 4G, or none.
•Network Operator.
The carrier that your device was activated for.
•Session Duration — How long you've been connected to the network.
•Session Total Data — Amount of data transferred over the lifetime of the device
(by network type) and in the current session.
•WAN Mode — Network(s) to connect to, and in what order.
·4G Preferred — Connection can be established to either 3G or 4G; if both
are available, 4G is used. This setting is recommended if your service
provider has no data limit for 4G, but does for 3G, or you want to take
advantage of the faster data transfer speeds of 4G.
·3G Preferred — Connection can be established to either 3G or 4G; if both
are available, 3G is used.
·4G Only — Connection can be established only to 4G.
·3G Only — Connection can be established only to 3G.
If you don’t have 4G coverage, you can save power by selecting "3G Only".
![](/img.php?id=1412542&img=bg53.png)
Settings
Rev 1 Oct.10 83
•Connect Automatically to the network when the AirCard W802S personal
hotspot powers on.
•Failover wait time — How long the device should wait, after it loses the
connection with the preferred network, before it attempts to connect to the
other network (not available if WAN mode is "3G only" or "4G only").
•Switchback wait time — How long the device should wait, when the less-
preferred network is connected and the preferred network becomes available,
before switching to the preferred network (not available if WAN mode is
"3G only" or "4G only").
•Update 3G PRL — Check whether an updated PRL is available.
The PRL (Preferred Roaming List) is an account configuration item set by
your service provider. It controls the radio channels and network carrier used
by the 3G modem. An updated PRL may improve your 3G network service.
Note: A 3G connection to the Internet won’t be available until the update is complete. (The
4G connection won’t be affected).
•Update 3G Profile — Check whether an updated profile for your 3G connection
is available.
An updated profile may improve your 3G network service.
4G Panel
To access this panel:
1. Log in to the home page.
2. Click Advanced settings ().
3. Click WAN > 4G.
Note: 4G information is not available if WAN mode is "3G only". (WAN mode is in
Advanced settings > WAN > Setup.)
From this window, you can view this 4G information:
•Connection Status — connected, or not connected.
•Coverage Type — 4G, 4G Off, or no service.
•RSSI and CINR.
RSSI reflects the signal strength of the network.
CINR stands for Carrier to Interference-plus-Noise Ratio, and is a measure-
ment of signal effectiveness. For the receiver to decode the carrier signal, the
latter must be in an acceptable CINR range.
•Tx Power — Transmitter power. A higher number is better.
•Center Frequency — Frequency of the 4G channel used for the data
connection.
•NSP-ID — ID of the 4G Network Service Provider.
•NAP-ID — ID of the 4G Network Access Provider.
•BSID — Base Station ID.
![](/img.php?id=1412542&img=bg54.png)
AirCard W802S User Guide
84 2400092
•Preable — Preamble ID of the current base station that the modem is listening
to.
•Realm — Login address used for 4G service (user@realm).
•Certificate information
Wi-Fi Tab
Network Panel
1. Log in to the home page.
2. Click Advanced settings ().
3. Click Wi-Fi > Network.
From this window, you can view and adjust settings, or perform the following
actions:
•Disable Wi-Fi upon USB-PC — Only a computer that is connected to the device
through the USB cable can use the device. See "Disabling Wi-Fi When
Connected Through USB" on page 93.
•SSID — Wi-Fi network name; identifies your Wi-Fi network and is visible to
other Wi-Fi-enabled devices. See "SSID (Wi-Fi Network Name)" on page 86.
•Hostname — Device name. See "Host Name (Device Name)" on page 92 and
"Displaying the Home Page of the Device" on page 46.
•Link SSID and Hostname. See "Linking the SSID and the Host Name" on
page 87.
If you link the SSID (Wi-Fi network name) and the Hostname (name of your
device):
•The SSID becomes whatever the Hostname is (you cannot change the SSID
— only the Hostname).
•You only need to remember one name when selecting the Wi-Fi network,
accessing the browser interface, or accessing the microSD card.
•SSID Broadcast.
If broadcast is enabled, the wireless network is displayed in the list of Wi-Fi
networks available in the local area. For increased security, set this field to
Disable. You will need to give the SSID to the people who will be accessing
your network.
•Max Number of Users
Limits the number of Wi-Fi users that can connect to the device. A smaller
number improves performance and security.
•Battery or USB Powered (power settings)
·Better battery life — At the cost of a shorter Wi-Fi range.
·Longer Wi-Fi range — At the cost of a shorter battery life.
•AC Powered (power settings)
·Longer Wi-Fi range
·Shorter Wi-Fi range
•Wi-Fi Channel
The Wi-Fi channel is the active channel of the Wi-Fi access point. If your net-
work is having performance issues (possibly caused by other Wi-Fi networks
in the vicinity using the same channel), try a different Wi-Fi channel.
![](/img.php?id=1412542&img=bg55.png)
Settings
Rev 1 Oct.10 85
•Basic Rate — Type of wireless devices connected to your network.
If you're certain that all of the Wi-Fi devices used with your device support
802.11g, then select 802.11g only (this ensures faster Wi-Fi speeds); other-
wise, select 802.11b/g compatibility.
•RTS Threshold
Specifies the smallest packet size, in bytes, for which RTS/CTS (Request to
Send/Clear to Send) handshaking is used. The recommended value is 2347.
Change this value only if you're experiencing inconsistent data flow. Make
only minor changes to this value.
•Fragmentation Threshold
Specifies the largest allowable size, in bytes, for a packet. If the packet is
larger than this, it is fragmented into multiple packet before it is transmitted. To
prevent poor network performance, it's recommended to keep this value as
large as possible (up to 2346).
•List of connected devices — Display a window that shows connected
computers.
A row may optionally show one or both of these icons:
• — The user of this computer is logged in as administrator.
• — This computer is connected to the device through the USB cable.
Security Panel
1. Log in to the home page.
2. Click Advanced settings ().
3. Click Wi-Fi > Security.
From this window, you can set the:
•Wi-Fi security type. See "Wi-Fi Security" on page 88.
•Wi-Fi password. See "Wi-Fi Password" on page 89.
•Wi-Fi Password Reminder feature. See "Wi-Fi Password Reminder" on
page 90.
MAC Filter Panel
The MAC (Media Access Control) filter is used to grant ("whitelist") or block
("blacklist") wireless devices access to the Wi-Fi, 3G, and 4G networks. Access is
based on the MAC address of each wireless device.
MAC filtering can prevent unauthorized wireless devices from connecting to your
network.
MAC filtering increases security of your network. You can give access to your
network, based on the MAC address of the wireless devices. This makes it harder
for a hacker to use a MAC address to access your network.
To access this panel:
1. Log in to the home page.
2. Click Advanced settings ().
3. Click Wi-Fi > MAC Filter.
![](/img.php?id=1412542&img=bg56.png)
AirCard W802S User Guide
86 2400092
From this window, you can:
•Display a list of computers that are:
·Allowed to access the network (MAC Filter Mode = "Allow all in list")
·Not allowed to access the network (MAC Filter Mode = "Block all in list")
•Add or remove a computer from the lists. See "Specifying Computers That
Can Access the Network" on page 90 and "Specifying Computers That Are
Not Allowed to Access the Network" on page 91.
•Display a list of computers that are currently connected through Wi-Fi. See
"Displaying a List of Currently Connected Computers" on page 92.
Configuring the Wi-Fi Network
You can configure basic settings of the Wi-Fi network through the setup pages.
1. Ensure you're logged in to the home page.
2. Click Admin setup().
For more information, see "Changing the Password and Settings" on page 38.
You can configure basic and advanced settings of the Wi-Fi network through the
Advanced settings window.
1. Log in to the home page.
2. Click Advanced settings ().
3. Click Wi-Fi > Network.
For more information, see "Network Panel" on page 84.
See also:
•"Disabling Wi-Fi When Connected Through USB" on page 93.
•"Battery and USB Power Settings" on page 73.
•"AC Power Settings" on page 73
SSID (Wi-Fi Network Name)
The SSID identifies your Wi-Fi network and is visible to other Wi-Fi-enabled
devices.
It appears on your device’s LCD screen; if more than one AirCard W802S
personal hotspot is available, you can use this name to tell the devices apart.
You can display the home page by typing the SSID in your Web browser (if Link
SSID and Hostname is selected; see "Linking the SSID and the Host Name" on
page 87).
You should make the SSID unique and change it on a regular basis for optimal
security.
![](/img.php?id=1412542&img=bg57.png)
Settings
Rev 1 Oct.10 87
To change the SSID:
1. Log in to the home page.
2. Click Advanced settings ().
3. Click Wi-Fi > Network.
4. In the SSID field, enter the new name.
If the SSID field is not available, Link SSID and Hostname is enabled. You
must either edit Hostname (and the SSID will get the same value), or disable
Link SSID and Hostname and edit the SSID.
5. Click Save.
6. Reconnect to Wi-Fi: follow the instructions on-screen, and see "How Do
I Connect to Wi-Fi?" on page 112.
Note: If you're sharing your connection with others, they also must reconnect to Wi-Fi;
provide them the new SSID.
For security reasons, it's recommended you disable SSID Broadcast. See "Network
Panel" on page 84.
Linking the SSID and the Host Name
If you link the SSID (Wi-Fi network name) and the Hostname (name of your
device):
•The SSID becomes whatever the Hostname is (you cannot change the SSID
— only the Hostname).
•You only need to remember one name when selecting the Wi-Fi network,
accessing the browser interface, or accessing the microSD card.
To link the SSID and the Hostname:
1. Log in to the home page.
2. Click Advanced settings ().
3. Click Wi-Fi > Network or Router > LAN.
4. Select the Link SSID and Hostname check box.
The SSID field gets the value of Hostname and becomes unavailable (grayed
out).
5. Click Save.
The device resets, after which you must reconnect to Wi-Fi. See "How Do
I Connect to Wi-Fi?" on page 112.
![](/img.php?id=1412542&img=bg58.png)
AirCard W802S User Guide
88 2400092
Wi-Fi Security
By default, Wi-Fi security is enabled for your device and the Wi-Fi network.
Note: All the devices used with the AirCard W802S personal hotspot must support the
selected security type.
To change the security used by Wi-Fi:
1. Log in to the home page.
2. Click Advanced settings ().
3. Click Wi-Fi > Security.
4. Select one of the options:
•None
No security (no password is required to access the Wi-Fi network); not recom-
mended. Anyone may access your device and use your Internet connection
(you are responsible for payment for data usage).
•WEP-64 Bit - Shared
Lower security. Works with older and newer Wi-Fi devices. Recommended
only if any of your devices don't support WPA or WPA2.
Shared WEP uses the same key for encryption and authentication; some con-
sider shared WEP to be less secure than open WEP.
•WEP-128 Bit - Shared
Lower security. Works with older and newer Wi-Fi devices. Recommended
only if any of your devices don't support WPA or WPA2.
Shared WEP uses the same key for encryption and authentication; some con-
sider shared WEP to be less secure than open WEP.
•WEP-64 Bit - Open
Lower security. Works with older and newer Wi-Fi devices. Recommended
only if any of your devices don't support WPA or WPA2.
Open WEP uses the key for encryption, but not for authentication.
•WEP-128 Bit - Open
Lower security. Works with older and newer Wi-Fi devices. Recommended
only if any of your devices don't support WPA or WPA2.
Open WEP uses the key for encryption, but not for authentication.
•WPA-Personal - TKIP
A strong security standard, supported by most Wi-Fi devices.
•WPA-Personal - TKIP/AES
A strong security standard, supported by most Wi-Fi devices.
•WPA2-Personal - AES
A stronger, newer security standard. Limited to newer Wi-Fi devices.
•WPA2-Personal - TKIP/AES
A stronger, newer security standard. Limited to newer Wi-Fi devices.
•WPA/WPA2 Personal (recommended setting)
Wi-Fi devices that use either WPA or WPA2 can connect to the device. Sup-
ported by most Wi-Fi devices.
![](/img.php?id=1412542&img=bg59.png)
Settings
Rev 1 Oct.10 89
5. Click Save.
The option you select determines the Wi-Fi security used and also the maximum
length of the Wi-Fi password.
Wi-Fi Password
If Wi-Fi security is enabled, a Wi-Fi password is required to connect to the Wi-Fi
network.
Some general rules to make your password more secure:
•Use letters and numbers
•Use special characters (for example, @)
•Use both uppercase and lowercase letters
To change the Wi-Fi password:
1. Log in to the home page.
2. Click Advanced settings ().
3. Click Wi-Fi > Security.
4. In the Wi-Fi Password field, type the password; the maximum length depends
on the Wi-Fi security type that you've selected.
•None
No security (no password is required to access the Wi-Fi network); not recom-
mended. Anyone may access your device and use your Internet connection
(you are responsible for payment for data usage).
•WEP-64 bit - Shared
5 ASCII characters.
•WEP-128 bit - Shared
13 ASCII characters.
•WEP-64 bit - Open
5 ASCII characters.
•WEP-128 bit - Open
13 ASCII characters.
•WPA-Personal - TKIP
ASCII string, 8 to 63 characters.
•WPA-Personal - TKIP/AES
ASCII string, 8 to 63 characters.
•WPA2-Personal - AES
ASCII string, 8 to 63 characters.
•WPA2-Personal - TKIP/AES
ASCII string, 8 to 63 characters.
•WPA/WPA2 Personal
ASCII string, 8 to 63 characters.
5. Click Save.
![](/img.php?id=1412542&img=bg5a.png)
AirCard W802S User Guide
90 2400092
Wi-Fi Password Reminder
When the Wi-Fi Password Reminder feature is enabled, you can display the Wi-Fi
password on the LCD of the device:
1. If the LCD is dark (no text or icons are displayed):
a. Ensure the LCD is enabled. See "Turning the LCD On or Off" on page 73.
b. Briefly press the power button on the device.
2. Press the power button on the device twice, quickly (within 0.5 seconds).
The information is displayed for approximately 20 seconds. To clear the
information before that, briefly press the power button on the device.
Enabling the Wi-Fi Password Reminder
1. Log in to the home page.
2. Click Advanced settings ().
3. Click Wi-Fi > Security.
4. In the Password Reminder section, select On.
5. Click Save.
Allowing or Denying Computers Access to the Network
The MAC (Media Access Control) filter is used to grant ("whitelist") or block
("blacklist") wireless devices access to the Wi-Fi, 3G, and 4G networks. Access is
based on the MAC address of each wireless device.
MAC filtering can prevent unauthorized wireless devices from connecting to your
network.
You can choose one of three modes:
•No filtering — All computers are allowed to access the network.
•Allow all in list — Only computers that are in this list are allowed to access the
network.
•Block all in list — All computers are allowed to access the network, unless
they're in this list.
In any case, a user still needs to provide the correct Wi-Fi password to access the
network.
Specifying Computers That Can Access the Network
1. Log in to the home page.
2. Click Advanced settings ().
3. Click Wi-Fi > MAC Filter.
4. In the MAC Filter Mode list, click Allow all in list.
5. Do one of the following:
•If the computer you want to allow access is currently connected to the
AirCard W802S personal hotspot, click List of connected devices.
In the row for the computer, click Add.
![](/img.php?id=1412542&img=bg5b.png)
Settings
Rev 1 Oct.10 91
•Click Add.
In the MAC Address field, enter the MAC address of the computer you're
adding to the list. (If you don't know this address, see "Finding the MAC
Address" on page 117.)
In the Name field, enter a name, for example "Amy's PC".
6. Repeat step 5 for each computer you want to allow access.
Specifying Computers That Are Not Allowed to Access the Network
1. Log in to the home page.
2. Click Advanced settings ().
3. Click Wi-Fi > MAC Filter.
4. In the MAC Filter Mode list, click Block all in list.
5. Determine and block an undesired user of your network.
a. Click the List of connected devices link.
b. If you see a device you don't recognize, you can compare its MAC
address to the MAC address of each of the devices on your network.
To determine the MAC address of each device you have, see "Finding the
MAC Address" on page 117. If none of your devices have this MAC
address, that device might be an intruder.
c. In the row for the device you want to block, click Add.
6. For each computer you want to block, repeat step 5.
Tip: The Connected Users window has a Block check box, available for each currently
connected user (except the administrator [ ]). See "Wi-Fi Users Information and
Settings" on page 56.
Removing a Computer From the Allowed or Disallowed Lists
1. Log in to the home page.
2. Click Advanced settings ().
3. Click Wi-Fi > MAC Filter.
4. In the MAC filter mode list, click either Allow all in list or Block all in list.
5. Click the row that you want to remove.
A row of buttons (Delete, OK, Cancel) appears.
6. Click Delete.
![](/img.php?id=1412542&img=bg5c.png)
AirCard W802S User Guide
92 2400092
Displaying a List of Currently Connected Computers
1. Ensure you're logged in to the home page.
2. Click the icon to display the Connected Users window.
— or —
Click Advanced settings > Wi-Fi > Mac Filter, and click List of connected devices.
A row displays the icon if the user is logged in as administrator.
Host Name (Device Name)
The host name is, in essence, a name you're giving the device.
The host name is shown on your device’s LCD screen; if more than one device is
available, you can use this name to tell the devices apart. See "Linking the SSID
and the Host Name" on page 87.
This name is also used when you type a command to access the:
•Home page. See "Displaying the Home Page of the Device" on page 46.
•microSD card. See "Accessing the microSD Card" on page 64.
To change the host name:
1. Log in to the home page.
2. Click Advanced settings ().
3. Click Wi-Fi > Network or Router > LAN.
4. In the Hostname field, enter a name for your device.
Input rules:
1-15 ASCII characters. Valid characters are:
·a-z
·A-Z
·0-9. Note that the host name cannot be all numbers.
·- (hyphen). Note that the host name cannot start or end with a hyphen.
Setting the Maximum Number of Wi-Fi Users
If your network is having performance issues, you might want to decrease the
number of Wi-Fi users allowed to connect to the device.
1. Ensure you're logged in to the home page.
2. Click the icon and, in the Connected Users window, click a value in the
Max Wi-Fi users list.
— or —
Click Advanced settings > Wi-Fi > Network, and click a value in the Max Number of
Users list.
![](/img.php?id=1412542&img=bg5d.png)
Settings
Rev 1 Oct.10 93
Wi-Fi Channel
The Wi-Fi channel is the active channel of the Wi-Fi access point. If your network
is having performance issues (possibly caused by other Wi-Fi networks in the
vicinity using the same channel), try a different Wi-Fi channel.
1. Log in to the home page.
2. Click Advanced settings ().
3. Click Wi-Fi > Network.
4. Click a channel in the Wi-FiChannel list, or, to have the device automatically
determine the channel to use, click Auto.
Disabling Wi-Fi When Connected Through USB
You can optionally turn off the device's Wi-Fi when connected via the USB cable.
In this case:
•Only a computer that is connected to the device through the USB cable can
use the device.
•You can prolong the battery life of the device.
•The battery charges faster.
To enable this feature:
1. Ensure you're logged in to the home page.
2. Click the Connected Users icon (for example, ) and select Disable Wi-Fi
when connected via USB.
— or —
Click Advanced settings > Wi-Fi > Network and set Disable Wi-Fi upon USB-PC to
On.
Configuring 3G/4G
Viewing 3G Activation Information
1. Log in to the home page.
2. Click Advanced settings ().
3. CLick Device > About.
The following fields are related to 3G activation:
•Activation Status
Activated, or not activated.
•Activation Date
Date that the 3G modem was first activated.
•Network Operator
The carrier that your device was activated for.
![](/img.php?id=1412542&img=bg5e.png)
AirCard W802S User Guide
94 2400092
3G Panel
1. Log in to the home page.
2. Click Advanced settings ().
3. Click WAN > 3G.
From this window, you can view or update this information, or perform these
actions:
•Connection Status: connected, not connected, or dormant.
Dormant means a connection is established, but no data is being transferred.
•Service Type used for the data connection (1xRTT, EVDO, or EVDO Rev. A).
•Coverage Type available, and RSSI and Ec/Io for each type.
RSSI reflects the signal strength of the network.
Ec/Io is a dimensionless ratio of the average power of a channel, typically the
pilot channel, to the total signal power.
•MDN (Mobile Directory Number) — a 10-digit phone number.
•SID (System ID)
The System ID identifies your home network area and is used in conjunction
with your phone number to determine if you are "home" or "roaming".
•MSID (Mobile Station ID)
The MSID is also known as IMSI (International Mobile Station Identity) — an
identifier of a device on the 3G network.
•NAI (Network Access Identifier)
The NAI is a user ID for accessing the 3G network.
•Roaming Status — Home, or roaming (outside of <Carrier_Name> coverage).
•Allow 3G Roaming — Enable or disable 3G roaming.
•PRL Version
The PRL (Preferred Roaming List) is an account configuration item set by
your service provider. It controls the radio channels and network carrier used
by the 3G modem. An updated PRL may improve your 3G network service.
•Load 3G PRL — For example, you've received via email or downloaded a file).
Alternatively, you can check online for a PRL update — in Advanced settings
> WAN > Setup, click Update 3G PRL.
Resetting the 3G/4G Configuration to Default Settings
Note: Reset the configuration only if instructed by a <Carrier_Name> representative.
After a configuration reset:
• You must go through the device setup (page 37) and 3G activation (the latter starts
automatically).
• Any changes you've made to the settings are lost.
1. Log in to the home page.
2. Click Advanced settings ().
![](/img.php?id=1412542&img=bg5f.png)
Settings
Rev 1 Oct.10 95
3. Click Device > About.
4. Click Reset Device to Factory Defaults.
5. When prompted, enter the SPC (Service Programming Code). (If you don't
know your SPC, contact <Carrier_Name>.)
You won't be able to establish a data connection until you:
1. Go through the device setup (page 37).
2. Go through 3G activation or, if using 4G, use pay-as-you-go.
Configuring the Router Tab
You can configure the routing hardware component of the device through the
Advanced Settings window.
1. Log in to the home page.
2. Click Advanced settings ().
3. Click Router.
4. Depending on the settings you want to configure, click one of the panels:
•Basic. See "Basic Panel" on page 95.
•LAN. See "LAN Panel" on page 96.
•Port Forward. See "Port Forward Panel" on page 100.
•Port Trigger. See "Port Trigger Panel" on page 102.
•DMZ. See "DMZ Panel" on page 104.
Basic Panel
1. Log in to the home page.
2. Click Advanced settings ().
3. Click Router > Basic.
From this window, you can enable or disable these features, or perform these
actions:
•Port forwarding. See "Port Forward Panel" on page 100.
•Port triggering. See "Port Trigger Panel" on page 102.
•DMZ. See "DMZ Panel" on page 104.
•UPnP (universal plug and play). See "UPnP (Universal Plug and Play)" on
page 96.
•SPI (stateful packet inspection). See "SPI (Stateful Packet Inspection)" on
page 96.
•Router Settings Reset — Reset the software to default settings. See "Resetting
the Software to Default Settings (Through the Browser Interface)" on
page 106.
![](/img.php?id=1412542&img=bg60.png)
AirCard W802S User Guide
96 2400092
UPnP (Universal Plug and Play)
UPnP provides simple and robust connectivity among consumer electronics,
intelligent appliances, and mobile devices from many different vendors. For more
information, see www.upnp.org.
Note: If UPnP is enabled, there are potential security risks.
Enabling UPnP
Before you can use UpnP, you must enable it.
1. Log in to the home page.
2. Click Advanced settings ().
3. Click Router > Basic.
4. Next to UPnP, select Enable.
SPI (Stateful Packet Inspection)
SPI, also known as "dynamic packet filtering," helps to prevent cyberattacks by
validating that the traffic passing through a session conforms to the protocol used
for this type of session. Packets that are not conforming get rejected.
Enabling SPI
Before you can use SPI, you must enable it.
1. Log in to the home page.
2. Click Advanced settings ().
3. Click Router > Basic.
4. Next to SPI, select Enable.
LAN Panel
1. Log in to the home page.
2. Click Advanced settings ().
3. Click Router > LAN.
From this window, you can view and adjust settings, or perform the following
actions:
•Router IP Address (on the LAN).
•Subnet Mask
The routing hardware's internal LAN subnet mask.
•Hostname (Device name). See "Host Name (Device Name)" on page 92 and
"Displaying the Home Page of the Device" on page 46.
•SSID (Wi-Fi network name). See "SSID (Wi-Fi Network Name)" on page 86.
•Link SSID and Hostname. See "Linking the SSID and the Host Name" on
page 87.
![](/img.php?id=1412542&img=bg61.png)
Settings
Rev 1 Oct.10 97
•DHCP Server (enable DHCP)
Note: The following items are displayed only when DHCP is enabled.
•DHCP IP Address Range
The starting and ending address of the range of IP addresses available for the
device to dynamically (that is, not permanently) assign to computers con-
nected to it.
•DHCP Lease Time
Amount of time, in minutes, a computer can use its assigned IP address
before it is required to renew the lease. After this time is up, the computer is
automatically assigned a new dynamic IP address.
Enter a number between 2 and 10080.
•Max DHCP Clients
The number of DHCP addresses that can be assigned and active at one time.
It's recommended you set this to a number greater than the number of Wi-Fi
users.
•DNS Mode
The DNS Mode setting specifies how the DNS servers (that the DHCP clients
are to communicate with) are obtained.
·Auto: Use the DNS server specified by <Carrier_Name>. DNS Relay is
enabled by default.
·Manual: The routing hardware assigns DHCP clients the DNS servers
specified in the Manual DNS Server #1 and #2 fields.
Use this option to access a DNS server that provides customized
addressing or if you have a local DNS server on your network.
If DNS Relay is disabled, the routing hardware rejects DNS requests
targeting the internal DNS proxy.
•Manual DNS Server #1 and #2 — Static IP addresses to use for the DNS
servers (if DNS Mode is Manual).
Available only if DNS Mode is Manual.
•DNS Relay
If enabled, and if DNS Mode (see above) is Manual, the routing hardware
assigns DHCP clients the DNS servers specified in the Manual DNS Server #1
and #2 fields.
If disabled, the routing hardware rejects DNS requests targeting the internal
DNS proxy.
The DNS Relay field is configurable and displayed only if DNS Mode is Manual.
If DNS Mode is Auto, DNS Relay is enabled by default.
•DHCP Static IP Assigment List — Assign a permanent IP address to a MAC
address, and view the static IP assignment list. See "DHCP Static IP
Assignment List" on page 99.
![](/img.php?id=1412542&img=bg62.png)
AirCard W802S User Guide
98 2400092
DHCP
DHCP (Dynamic Host Control Protocol) automatically assigns an IP address to
each device on the network and manages other network configuration information
for devices connected to your network. You do not need to manually configure the
IP address on each device that's on your network.
The assigned IP addresses are not permanent (as opposed to when using static
IP).
Most ISPs (Internet Service Providers) use DHCP.
Normally, you should enable DHCP, in which case you must configure each
device on the network with one of the following:
•TCP/IP settings set to "Obtain an IP address automatically"
•TCP/IP bound to the Ethernet connection with DHCP
If DHCP is disabled, you must configure each device on the network with:
•Fixed (permanent/static) IP address.
•DNS server addresses (provided by <Carrier_Name>).
Enabling DHCP
1. Log in to the home page.
2. Click Advanced settings ().
3. Click Router > LAN.
4. Next to DHCP Server, select Enable.
Configuring DHCP
To configure DHCP settings, DHCP must be enabled (Advanced settings > Router
> LAN > DHCP Server).
You can set the following DHCP settings in Advanced settings > Router > LAN:
•DHCP IP Address Range
The starting and ending address of the range of IP addresses available for the
device to dynamically (that is, not permanently) assign to computers con-
nected to it.
The start address must be 192.168.0.10 or above.
The ending address must be 192.168.0.50 or below.
•DHCP Lease Time
Amount of time, in minutes, a computer can use its assigned IP address
before it is required to renew the lease. After this time is up, the computer is
automatically assigned a new dynamic IP address.
Enter a number between 2 and 10080.
•Max DHCP Clients
The number of DHCP addresses that can be assigned and active at one time.
It's recommended you set this to a number greater than the number of Wi-Fi
users.
![](/img.php?id=1412542&img=bg63.png)
Settings
Rev 1 Oct.10 99
•DNS Mode
The DNS Mode setting specifies how the DNS servers (that the DHCP clients
are to communicate with) are obtained. See "DNS Mode" on page 100.
•DHCP Static Assignment List — Assign a permanent (static) IP address to a
device on your network, and view the static IP assignment list. See the next
section.
DHCP Static IP Assignment List
With DHCP, IP addresses are assigned dynamically; devices typically don't have
a permanent IP address.
However, in some cases you might want to assign a static
(permanent) IP address to a device, while still using DHCP for the rest of the
devices on your network. This is also known as "DHCP reservation". You might
want to do this with, for example, a Web server, FTP server, media server.
Viewing the Static IP Assignment List
1. Log in to the home page.
2. Click Advanced settings ().
3. Click Router > LAN.
4. Ensure DHCP is enabled (DHCP Server).
5. Click DHCP Static IP Assignment List.
Assigning an IP Address Based on a MAC Address
1. Follow the above steps to display the DHCP Static IP Assignment List
window.
2. In the Hostname field, enter a meaningful description of the device.
3. In the MAC Address field, enter the MAC Address of the device. (If you don't
know this address, see "Finding the MAC Address" on page 117.)
4. In the IP Address field, enter the IP address you want to assign to the device.
5. Select the Enable check box to have the device use the designated IP
address.
6. Click Add.
7. Click save.
Removing an IP Address Based on a MAC Address
1. Click DHCP Static IP Assignment List on the LAN panel of the Router tab.
2. To keep the device information in the list (in case you want to re-enable
DHCP for this MAC address later on), clear the Enable check box.
— or —
To remove the device from the list:
a. Click the row that you want to remove.
A row of buttons (Delete, OK, Cancel) appears.
b. Click Delete.
![](/img.php?id=1412542&img=bg64.png)
AirCard W802S User Guide
100 2400092
DNS Mode
The DNS Mode setting specifies how the DNS servers (that the DHCP clients are
to communicate with) are obtained.
1. Log in to the home page.
2. Click Advanced settings ().
3. Click Router > LAN.
4. Set DNS Mode to one of the following:
•Auto: Use the DNS server specified by <Carrier_Name>. DNS Relay is
enabled by default.
•Manual: The routing hardware assigns DHCP clients the DNS servers
specified in the Manual DNS Server #1 and #2 fields.
Use this option to access a DNS server that provides customized addressing
or if you have a local DNS server on your network.
If DNS Relay is disabled, the routing hardware rejects DNS requests targeting
the internal DNS proxy.
For information on DNS Relay, see "LAN Panel" on page 96.
Port Forward Panel
Normally, incoming traffic (from the Internet) is blocked. However, port forwarding
lets you forward incoming traffic to specific ports and devices (per their local IP
address) on your network. For example, you can configure port forwarding so
that:
•You can access your Remote Desktop from the Internet (by specifying the
WAN [public] IP address that the device is using).
•Internet users can access a Web, FTP, or email server, or gaming or Internet
application hosted by your computer.
Note: Port forwarding creates a security risk. When not required, port forwarding should
be disabled.
Port forwarding does not apply to normal browsing, file downloading, running most online
games or other applications hosted on the Internet. (Some online games require port
forwarding.)
Before you can use or configure port forwarding, you must enable it. See
"Enabling Port Forwarding" on page 101.
From the Port Forward panel of the Router tab of the Advanced Settings window, you
can:
•Enable port forwarding for an application. See "Enabling Port Forwarding for
an Application" on page 101.
•Remove an application from the port forwarding list. See "Disabling Port
Forwarding for an Application" on page 101.
![](/img.php?id=1412542&img=bg65.png)
Settings
Rev 1 Oct.10 101
Enabling Port Forwarding
Before you can use or configure Port Forwarding, you must enable it.
1. Log in to the home page.
2. Click Advanced settings ().
3. Click Router > Basic.
4. Next to Port Forwarding, select Enable.
5. Click Save.
Enabling Port Forwarding for an Application
1. Ensure you've enabled port forwarding. See "Enabling Port Forwarding" on
page 101.
2. Display the "Port forward" window.
a. Log in to the home page.
b. Click Advanced settings ().
c. Click Router > Port Forward.
3. In the last row of the table, click the Application field, and select the application
type from the list.
The values for Start and End ports are automatically filled in.
4. If necessary, change the range of port numbers associated with the appli-
cation. Traffic will be allowed (not blocked) if its destination port number is in
the specified range.
a. In the Start field, enter the number that starts the port range.
b. In the End field, enter the number that ends the port range.
If the range consists of only one port, enter the number that you entered
in the Start field.
5. In the Protocol list, click the protocol(s) used for this application (TCP, UDP, or
both).
6. In the IP Address field, enter the IP address of the server to be accessed.
7. Ensure Enable is selected.
8. Click Add.
9. Click save.
Disabling Port Forwarding for an Application
1. Ensure you've enabled port forwarding. See "Enabling Port Forwarding" on
page 101.
2. Display the "Port forward" window.
a. Log in to the home page.
b. Click Advanced settings ().
c. Click Router > Port forward.
![](/img.php?id=1412542&img=bg66.png)
AirCard W802S User Guide
102 2400092
3. To keep the application in the list (in case you want to re-enable port
forwarding later on), clear the Enable check box.
— or —
To remove the application from the list:
a. Click the row that you want to remove.
A row of buttons (Delete, OK, Cancel) appears.
b. Click Delete.
Port Trigger Panel
Some applications require multiple ports open for communication, many of which
may be initiated by a computer on the WAN. Examples of this include video
conferencing, VoIP (Internet telephony), and Internet gaming.
With port triggering, the device monitors outgoing data on specific port numbers
(trigger ports).
The device keeps track of the IP address of the computer that sends data on
these trigger ports, so that when incoming data on the Forward ports arrives, the
device sends the incoming data to the same computer.
Before you can use or configure port triggering, you must enable it. See "Enabling
Port Triggering" on page 102.
From the Port Trigger panel of the Router tab of the Advanced Settings window, you
can:
•Enable port triggering for specified protocols and ports. See "Enabling Port
Triggering for Specified Protocols and Ports" on page 102.
•Remove protocols and ports from the port triggering list. See "Removing
Ports from the Port Triggering List" on page 103.
Enabling Port Triggering
Before you can use or configure Port Triggering, you must enable it.
1. Log in to the home page.
2. Click Advanced settings ().
3. Click Router > Basic.
4. Next to Port Triggering, select Enable.
Enabling Port Triggering for Specified Protocols and Ports
1. Ensure you've enabled port triggering. See "Enabling Port Triggering" on
page 102.
2. Display the "Port trigger" window.
a. Log in to the home page.
b. Click Advanced settings ().
c. Click Router > Port Trigger.
![](/img.php?id=1412542&img=bg67.png)
Settings
Rev 1 Oct.10 103
3. In the last row of the table, in the first Protocol list, click the protocol(s) used by
the application for outgoing traffic (to the Internet, sent through the trigger
ports).
4. In the Trigger Ports field, enter the port number(s) used to determine that the
application is in use (that is, specify the port number or range of port numbers
that the application uses for outgoing traffic). (Check the user documentation
for the application.)
To specify a range of port numbers, separate the start and end port number
with a hyphen.
5. In the second Protocol list, click the protocol(s) used by the application for
incoming traffic (from the Internet).
6. In the Forward Ports field, enter the ports to forward to the computer that
triggered the rule (that is, specify the port number or range of port numbers
that the application uses for incoming traffic). (Check the user documentation
for the application.)
To specify a range of port numbers, separate the start and end port number
with a hyphen.
7. Ensure Enable is selected.
8. Click Add.
9. Click Save.
Removing Ports from the Port Triggering List
1. Ensure you've enabled port triggering. See "Enabling Port Triggering" on
page 102.
2. Display the "Port trigger" window.
a. Log in to the home page.
b. Click Advanced settings ().
c. Click Router > Port Trigger.
3. To keep the entry in the list (in case you want to re-enable this entry later on),
clear the Enable check box.
— or —
To remove the entry from the list:
a. Click the row that you want to remove.
A row of buttons (Delete, OK, Cancel) appears.
b. Click Delete.
![](/img.php?id=1412542&img=bg68.png)
AirCard W802S User Guide
104 2400092
DMZ Panel
DMZ stands for "demilitarized zone". You can select one computer to receive all
unsolicited incoming connections.
The IP address of the DMZ is the default recipient of incoming packets (from the
Internet) that are not handled by port forwarding rules, port triggering rules, or
NAT'd connections:
1. If port forwarding, port triggering, or both are enabled, incoming traffic is
routed according to the port forwarding rules, port triggering rules, or NAT'd
connections.
2. If incoming traffic was not routed as a result of the above:
·If DMZ is enabled, then incoming traffic is routed to the computer that uses
the IP address specified by the DMZ settings.
·If DMZ is not enabled, the incoming traffic is blocked.
Note: Putting a computer in the DMZ opens all the ports of that computer, and exposes
that computer to various security risks. Use this option only as a last resort — if possible,
use other options instead (for example, port forwarding or port triggering).
Before you can use or configure DMZ, you must enable it.
Enabling DMZ
Before you can use or configure DMZ, you must enable it.
1. Log in to the home page.
2. Click Advanced settings ().
3. Click Router > Basic.
4. Next to DMZ, select Enable.
5. Click Save.
Configuring DMZ
To configure DMZ:
1. Ensure you've enabled DMZ. See "Enabling DMZ" on page 104.
2. Display the DMZ panel of the Router tab.
a. Log in to the home page.
b. Click Advanced settings ().
c. Click Router > DMZ.
3. Specify the computer that you want exposed to the Internet: in the Destination
IP Address field, enter the IP address of the computer.
If you don't know how to find the IP address, see "Finding the IP Address" on
page 118.
4. In the Source IP Address section, specify what incoming traffic (not handled by
port forwarding, port triggering, or NAT) to forward to this computer.
To forward all incoming traffic, click Any.
![](/img.php?id=1412542&img=bg69.png)
Settings
Rev 1 Oct.10 105
— or —
To forward incoming traffic from certain IP addresses:
a. Click Restriction.
b. In the two additional fields that are displayed, enter the start and end
IP addresses of a range.
5. Using the DHCP Static IP Assignment List, assign an IP address based on
the MAC address of the computer that is in the DMZ. See "Assigning an
IP Address Based on a MAC Address" on page 99.
— or —
On the computer that is in the DMZ, disable DHCP, and manually assign the
IP address, gateway, and DNS server.
Resetting the Software to Default Settings
Warning: If you reset the software to default settings:
• You must go through the device setup (page 37), as if you've just purchased the device.
• Any changes you've made to the settings are lost.
Your 3G and 4G account information is not affected; after reset, the device remains provi-
sioned for service.
You'll need to reset the software to default settings if:
•You've forgotten the administrator password.
•You've changed the DHCP settings such that the device is inoperable (for
example, there's no communication with the device).
You have two options to initiate the reset:
•Through the software. See "Resetting the Software to Default Settings
(Through the Browser Interface)" on page 106.
•Through the reset button on the device. See the following section.
Resetting the Software to Default Settings (Through the Reset Button)
1. Remove the battery compartment cover.
![](/img.php?id=1412542&img=bg6a.png)
AirCard W802S User Guide
106 2400092
2. Find the small hole below and to the right of the battery compartment. The
reset button is inside this hole.
3. Insert a thin object (for example, the end of a paper clip) into the hole, and
lightly press on the bottom of the hole for five or more seconds.
4. Replace the battery compartment cover.
5. Check the device LCD. If it displays "Reset to factory defaults? Press to
accept", press the power button on the device.
6. Follow the instructions on the device LCD.
Resetting the Software to Default Settings (Through the Browser Interface)
Warning: If you reset the software to default settings:
• You must go through the device setup (page 37), as if you've just purchased the device.
• Any changes you've made to the settings are lost.
Your 3G and 4G account information is not affected; after reset, the device remains provi-
sioned for service.
1. Log in to the home page.
2. Click Advanced settings ().
3. Click Router > Basic.
4. Click Router Settings Reset.
Reset button
![](/img.php?id=1412542&img=bg6b.png)
Settings
Rev 1 Oct.10 107
5. Check the device LCD. If it displays "Reset to factory defaults? Press to
accept", press the power button on the device.
6. Follow the instructions on the device LCD.
Exporting and Importing Settings
Exporting Settings
Settings include configuration information for the device, network, and browser
interface.
You can, for example, save the current configuration, then make some changes
and test them. You can then use the Import button to restore (load) the saved
configuration.
To export the settings to a text file:
1. Log in to the home page.
2. Click Advanced settings ().
3. Click Device > Basic.
4. Click Export.
Importing Settings
1. Log in to the home page.
2. Click Advanced settings ().
3. Click Device > Basic.
4. Browse to and click the file with the previously exported settings.
5. Click Import.
Note: Your device may reset, and you may need to reconnect to Wi-Fi and the Internet.
See "How Do I Connect to Wi-Fi?" on page 112 and "Launching Your Network
Connection" on page 51.
Logs
Logs Available
The following types of logs are available:
•Connect/disconnect. See the following section.
•System events. See "System Events" on page 108.
![](/img.php?id=1412542&img=bg6c.png)
AirCard W802S User Guide
108 2400092
Connection History
The connection history shows the time of connections to and disconnections from
the Internet.
Note: The connection history does not log the amount of data transferred. In the Internet
Connection Information window, you can view information on the current billing cycle and
lifetime of the device; see "Internet Connection Information" on page 58.
Enabling and Disabling Logging of Connect/Disconnects
1. Log in to the home page.
2. Click Advanced settings ().
3. Click Device > Log.
4. In the Connect/Disconnect section, select Enable or Disable.
5. Click save.
Exporting the Connection History
1. Log in to the home page.
2. Click Advanced settings ().
3. Click Device > Log.
4. Ensure Connection/Disconnect is set to Enable.
5. Click Export.
Clearing the Connection History
1. Log in to the home page.
2. Click Advanced settings ().
3. Click Device > Log.
4. In the Connect/Disconnect section, click Clear log.
System Events
You can enable or disable, as a group, the logging of the following events:
•Software update available
•Network update available
•Primary WAN failover
•Primary WAN switchback
•Unexpected data connection loss
•Changes to miscellaneous settings
![](/img.php?id=1412542&img=bg6d.png)
Settings
Rev 1 Oct.10 109
The following system events are always logged:
•Intrusion alerts
•Unexpected power loss
•Critical battery
•Critical temperature
•Routing hardware settings reset
•Firmware update
Enabling and Disabling Logging of System Events
1. Log in to the home page.
2. Click Advanced settings ().
3. Click Device > Log.
4. In the Verbose System Event Logging section, select Enable or Disable.
5. Click save.
Note: Certain events are always logged; see "System Events" on page 108.
Exporting System Events
1. Log in to the home page.
2. Click Advanced settings ().
3. Click Device > Log.
4. Ensure Verbose System Event Logging is set to Enable.
5. Click Export.
Clearing the System Events Log
1. Log in to the home page.
2. Click Advanced settings ().
3. Click Device > Log.
4. Ensure Verbose System Event Logging is set to Enable.
5. Click Clear log.
Setting the Method Used for Time Acquisition
Time information is stored in the connection history log and system events log.
To set the method used for obtaining the time:
1. Log in to the home page.
2. Click Advanced settings ().
3. Click Device > Log.
![](/img.php?id=1412542&img=bg6e.png)
AirCard W802S User Guide
110 2400092
4. Select the 3G or the NTP check box.
3G — Time information is obtained from the 3G (CDMA) network; this is more
accurate than NTP, but requires 3G coverage.
NTP — The device's clock is synchronized to a Network Time Protocol server
on the Internet; not as accurate as when using the 3G setting, but doesn't
require 3G coverage. Use this setting if you have 4G but no 3G coverage.
Setup Pages
Welcome to Your Device Window - Select an Option
The “Welcome to Your AirCard W802S window” opens:
•Automatically, as part of the initial setup of your newly purchased device.
•When you click Admin Setup ( ) from the home page (you must be logged
in).
Note: This window displays the administrator password and the address of the device
home page. Please remember this information or write it down in a safe place.
This window provides several options.
•To keep the default settings of the device, select one of the following:
·The Internet (to start surfing)
·My AirCard W802S's home page (to view the device status, customize
settings).
•To change security settings, select Set up my AirCard W802S.
![](/img.php?id=1412542&img=bg6f.png)
Rev 1 Oct.10 111
6
6: Resources
More Information
Visiting the <Carrier_Name> Website
Check www.<Carrier_Name>.com/support for product updates and
support.
Contacting Customer Service
You can reach <Carrier_Name> Customer Service by:
•Visiting www.<Carrier_Name>.com/support
Online Help
1. In the browser interface, click the Help button ( ) and, from the
menu, select Online Help.
The Help system opens in a new Web browser window or tab.
You have several options to find the information you need:
•Browse the Table of Contents.
•Use the Index or Search feature: click the appropriate button in
the lower left part of the help window, and type the information
you're looking for.
Other Ways to View Help Information
•Some windows have a icon. Click the icon to view Help infor-
mation.
•When you move the cursor over a field or button in Advanced
Settings, help information, if available, appears to the right of the
window.
Contextual Help in the Advanced Settings Window
When you move the cursor over a field or button in Advanced Settings,
help information on this item, if available, appears to the right of the
window.
To turn this feature on or off:
1. Ensure you're logged in to the home page.
2. Click Advanced settings > Device > Basic.
3. Set Help for Advanced Settings to Show or Hide.
4. Click Save.
![](/img.php?id=1412542&img=bg70.png)
AirCard W802S User Guide
112 2400092
Frequently Asked Questions
How Can I Tell I'm Connected to 3G/4G?
When you're connected:
•The 3G or 4G icon (on the left side of the home page) is solid. For example,
.
•The bottom area of the device LCD, the Virtual Device, and the Mini Window
show the data transfer icon and data transfer information (amount of
data; connection duration).
How Do I Connect to Wi-Fi?
You may have to manually connect to Wi-Fi after certain events — for example, as
part of the initial device setup, or after a software update.
Tip: The Wi-Fi network name is displayed on the device LCD.
1. Do one of the following, depending on your operating system.
Windows
Windows 7: Right-click the icon in the system tray.
Windows Vista: Click Control Panel > Network and Internet > Network and Sharing
Center > Connect to a network.
Windows XP: Click Control Panel > Network Connections > Wireless Network
Connections > View available wireless networks.
Mac
Click the AirPort icon (in the upper right corner of your screen).
Linux
Please see the user documentation of the Linux distribution.
Other operating systems
Please see the user documentation for your operating system or computer.
2. Select the Wi-Fi network provided by the AirCard W802S personal hotspot
and connect to it. (If prompted for a network key/security key/password, enter
the Wi-Fi password.)
Is Roaming on 4G Supported?
At the time of this release, roaming on 4G is not supported.
What Do I Do if I Forgot the Wi-Fi Password?
•If the Wi-Fi Password Reminder feature is enabled, display the password on
the device. See "Wi-Fi Password Reminder" on page 90.
•Connect the device to your computer through USB, then log in and view the
Wi-Fi password (in Advanced settings > Wi-Fi > Security). Write the password
down in a safe place. See "Connecting Through USB" on page 30.
![](/img.php?id=1412542&img=bg71.png)
Resources
Rev 1 Oct.10 113
Note: If you've forgotten both the Wi-Fi password and the administrator (login) password,
then you must reset the software to default settings. See "Resetting the Software to
Default Settings" on page 105.
What Do I Do if I Forgot the Administrator Password?
1. Reset the software to default settings. See "Resetting the Software to Default
Settings" on page 105.
2. Go through the device setup, during which the administrator password will be
displayed; write it down in a safe place. See "Setting Up the Device" on
page 37.
How Do I Access My Corporate Network Through a
VPN?
1. Establish a connection to the 3G/4G network.
2. Launch the extranet client provided by your company.
3. Supply the appropriate user name and password to gain access.
For support, contact your company help desk.
Are Terminal Sessions Supported?
Terminal sessions (for example, via telnet or ssh) are not supported.
Tips
Extending Battery Life
•Consider purchasing and using a high-capacity battery (available at https://
www.sierrawireless.com/eStore/).
•When you're not using the device, turn it off, or end the 3G/4G connection.
(Click Disconnect on the home page).
•Connect the device, through the USB cable, to the power adapter or a
computer, and disable Wi-Fi. See "Disabling Wi-Fi When Connected Through
USB" on page 93.
•Adjust the LCD — do one or more of the following:
·Turn off the LCD (Advanced settings > Device > Display > LCD Backlight).
·Decrease the brightness of the LCD (Advanced settings > Device > Display
> Backlight Settings > On Battery/USB Power).
·Set the LCD to turn off sooner. See "Setting the LCD Timeout" on page 74.
•Configure the setting (for when battery powered or connected via USB) to
"Better battery life" (Advanced settings > Wi-Fi > Network > Battery or
USB powered).
•Enable standby (low power) mode. See "Standby (Low Power) Mode" on
page 57.
![](/img.php?id=1412542&img=bg72.png)
AirCard W802S User Guide
114 2400092
•Turn off the lighting of the power button (i.e. LED) (Advanced settings
> Device > Display > Power Button LED).
•Limit the number of Wi-Fi users (Advanced settings > Wi-Fi > Network > Max
Number of Users).
•If you have 3G but not 4G coverage, set WAN Mode to "3G only" (Advanced
settings > WAN > Setup > WAN Mode).
Device Location
•Avoid moisture or extreme temperatures.
•For improved reception, place the device near a closed window.
•Place your device within easy reach of a reliable power supply and the
computer to which it will be connected.
Improving Signal Strength
•Consider purchasing and using the Home Crib (available at https://
www.sierrawireless.com/eStore/).
•Ensure you're inside the network coverage area.
•Try reorienting your device.
•Move the device and your computer to another location — you may be in or
near a structure that is blocking the signal. Every obstacle (for example, walls,
ceilings, furniture) between the AirCard W802S personal hotspot and other
wireless devices decreases the signal strength.
•Place the device in a centralized location, as high as possible in the room.
•Make sure there’s plenty of space around your device to provide the best
signal reception.
•Keep the device at least 3-6 feet away from electrical devices that generate
RF interference (for example, microwaves, TVs, 2.4 GHz cordless phones,
cellular phones, baby monitors, wireless speakers). If you're not using these
electrical devices, turn them off.
•If possible, place your devices so that the signal passes through open
doorways or drywall, as opposed to concrete, brick, metal, walls with
insulation, and so on.
•If you cannot obtain service, contact <Carrier_Name> — a network or
account problem may be preventing you from obtaining service.
![](/img.php?id=1412542&img=bg73.png)
Resources
Rev 1 Oct.10 115
Improving 3G Network Service
To improve your network service, periodically check for PRL and profile updates.
The PRL (Preferred Roaming List) is an account configuration item set by your
service provider. It controls the radio channels and network carrier used by the
3G modem.
To check for these updates:
1. Log in to the home page.
2. Click Advanced settings ().
3. Click WAN > Setup.
4. Click Update 3G PRL.
5. After the update checking is completed, click Update 3G Profile.
Improving Wi-Fi Performance
•Try a different channel number. See "Wi-Fi Channel" on page 93.
•Check whether any device updates are available. See "Updates" on page 65.
•See the tips in "Improving Signal Strength" on page 114.
•Limit the number of Wi-Fi users (Advanced settings > Wi-Fi > Network > Max
Number of Users).
•Select a longer Wi-Fi range. (Advanced settings > Wi-Fi > Network > Longer Wi-Fi
range [two locations: Battery or USB Powered, and AC Powered])
Windows XP Users
1. Open the Device Manager.
a. Click start > Settings > Control Panel.
b. Double-click System.
c. Click Hardware.
d. Click Device Manager.
2. Double-click Network adapters.
![](/img.php?id=1412542&img=bg74.png)
AirCard W802S User Guide
116 2400092
3. Double-click the Wi-Fi client network adapter of your computer — for
example, “Intel(R) WiFi Link 5100 AGN” in the following screenshot.
4. If the Wi-Fi client network adapter is by Intel, click Advanced and, in the
Property list, click Power Management and move the slider all the way to the
right (to Highest). Click OK.
— or —
If the Wi-Fi client network adapter is not by Intel, select a configuration with
minimal power savings (to maximize throughput).
Note: The above settings are often controlled by 3rd-party value-add applications and may
be automatically changed. If Wi-Fi performance improves for a while after performing the
above steps, but then declines, recheck the above settings.
Security Tips
•Change the Wi-Fi network name (SSID) and Wi-Fi password on a regular
basis. See "SSID (Wi-Fi Network Name)" on page 86 and "Wi-Fi Password"
on page 89
•Disable SSID Broadcast. See "Network Panel" on page 84.
•Use the highest level of Wi-Fi security that your devices support. See "Wi-Fi
Security" on page 88.
•Change the login password. See "Changing the Administrator Password" on
page 77.
![](/img.php?id=1412542&img=bg75.png)
Resources
Rev 1 Oct.10 117
•Use MAC filtering to specify computers that are or aren't allowed to connect
to the network. See "MAC Filter Panel" on page 85.
Finding the MAC Address
You'll need to know the MAC address of a device, when performing any of the
following:
•Assigning an IP address based on a MAC address (when using DHCP). See
"DHCP Static IP Assignment List" on page 99.
•Allowing or denying computers access to the network. See "Allowing or
Denying Computers Access to the Network" on page 90.
Tip: You can display a list of connected devices, including the MAC address of each
device: click List of connected devices, available from Advanced settings > Wi-Fi
>MACFilter and Advanced settings > Wi-Fi > Network.
The steps to finding the MAC address of a device vary, depending on your
operating system.
Windows
1. Open a command prompt window.
a. Click start and Run.
b. Typ e cmd or command, and click OK.
2. At the command prompt, type ipconfig/all and press Enter.
3. Write down the Physical Address for the entry that relates to the wireless
network connection; it appears as a series of numbers and letters — this is
the MAC address of your wireless adapter.
Mac OS X
1. From the Apple menu ( ), select System Preferences.
2. Select Network.
3. Select the adapter that is connecting to the routing hardware.
4. Select Advanced.
5. Select Ethernet. The Ethernet ID is listed. This is the same as the MAC
address.
Linux
Please see the user documentation of the Linux distribution.
Other operating systems
Please see the user documentation for your operating system or computer.
![](/img.php?id=1412542&img=bg76.png)
AirCard W802S User Guide
118 2400092
Finding the IP Address
You'll need to know the IP address of a device, when configuring any of the
following:
•Port forwarding
•Port triggering
•DMZ
•Static DHCP features
To find the IP address of a device:
Windows
1. Open a command prompt window.
a. Click start and Run.
b. Typ e cmd or command, and click OK.
2. At the command prompt, type ipconfig and press Enter.
3. Write down the IP Address for the entry that relates to the wireless network
connection. (The IP address might be listed under "Ipv4 Address", or
something similar.)
Mac OS X
1. From the Apple menu ( ), select System Preferences.
2. Select Network.
3. Select the wireless adapter. The IP address is displayed in the right pane.
Other operating systems
Please see the user documentation for your operating system or computer.
Troubleshooting Tips
General tips
•Check the system events log. See "Exporting System Events" on page 109.
•If some settings are preventing you from connecting to Wi-Fi, connect to the
device through the USB cable, and then change the settings. See "Require-
ments for a USB Tethered Connection" on page 43 and "Making a Tethered
Connection" on page 43.
•Go to www.<Carrier_Name>.com/support to access troubleshooting and
other resources.
•The knowledge base at the Sierra Wireless website (www.sierrawireless.com/
support/customer_help.aspx) may also be useful.
![](/img.php?id=1412542&img=bg77.png)
Resources
Rev 1 Oct.10 119
LCD Is Dark
The LCD is dark and is not displaying any text or icons if:
•The device is turned on and:
·The LCD is turned off (Advanced settings > Device > Display > LCD Backlight).
·The LCD is turned on, but the LCD is dormant (inactivity timeout). To make
the LCD active, briefly press the power button on the device.
·The device is in standby (low power) mode. To exit this mode, briefly press
the power button on the device.
•The device is turned off.
To turn the device on:
a. Ensure a battery is inserted into the device.
b. Press the power button on the device for approximately two seconds.
If the LCD is still dark, use the USB cable to connect the device to the power
adapter or to a computer.
Insufficient Signal Strength
If you have insufficient signal strength, the icon is displayed (on the left side
of the home page).
Insufficient signal strength may occur because:
•You are outside the network coverage area.
•Your device’s internal antenna is pointing in the wrong direction.
•You are in or near a structure that is blocking the signal.
•You are near a device that is causing radio signal interference.
•A network or account problem is preventing you from obtaining service.
See also "Improving Signal Strength" on page 114.
Messages Displayed on the Device LCD
See also "SD Card Error" on page 50.
3G Activation Failed
If this message is displayed on the device LCD or in the 3G Activation Required
alert window (after you've attempted activation):
1. Ensure you're in 3G coverage and the signal strength is strong.
2. Turn the device off and on. See "Turning Your Device Off" on page 48 and
"Turning Your Device On" on page 33.
3. If the "Activation failed" message is still displayed, prepare the following, and
contact <Carrier_Name>:
·Your billing information.
·ESN of the device (displayed on the packaging, on the device [under the
battery], and at Advanced settings > Device > About).
![](/img.php?id=1412542&img=bg78.png)
AirCard W802S User Guide
120 2400092
Connecting to 3G/4G
If the LCD displays this message for a long time:
1. Check the signal strength. If it is weak, try the tips in "Improving Signal
Strength" on page 114.
2. Try a different Connection Preferences setting. See "Mobile Broadband Infor-
mation and Settings" on page 54.
3. Turn the device off and on. See "Turning Your Device Off" on page 48 and
"Turning Your Device On" on page 33.
4. Update the 3G profile: click Advanced settings > WAN > Setup > Update 3G
Profile.
5. If you're still unable to connect to 3G/4G, contact <Carrier_Name>.
Connection Error
If this message persists on the device LCD, update the 3G profile:
1. Log in to the home page.
2. Click Advanced settings ().
3. Click WAN > Setup.
4. Click Update 3G Profile.
5. If an error message and number are displayed on the LCD after the update,
note the information and contact <Carrier_Name>.
3G Activation Required
If the LCD displays this message, display the 3G Activation Required alert and
start the activation:
1. In the Admin Login section (in the upper left area of the home page), enter the
administrator password (1–20 characters/numbers). (The default password is
"password".)
2. Click OK.
3. Click the alerts icon to display the alert window.
4. If more than one alert is available, use the and buttons (at the top of the
alert window) to browse to the "3G Activation Required" alert.
5. In the 3G Activation Required alert window, click Activate now.
Tip: Alternatively, click Advanced settings > WAN > Setup > Update 3G Profile.
Searching for Network
The LCD displays this message until a 3G or 4G network is acquired.
If this message persists, see the tips in "Cannot Connect to the 3G/4G Network"
on page 123.
![](/img.php?id=1412542&img=bg79.png)
Resources
Rev 1 Oct.10 121
Update Failed
If this message appears on the device LCD or in the 3G Network Update
Available or Software Update Available alert windows (after you've attempted the
update):
1. Ensure your device is connected to the power adapter or computer, through
the USB cable.
Note: If you’ll be using USB for data transfer (and not just for charging the device), you
must install the device driver. See "Making a Tethered Connection" on page 43.
2. Retry the update.
3. If the "Update failed" message is still displayed, contact <Carrier_Name>.
Cannot Connect to Wi-Fi
If your computer cannot connect to the Wi-Fi network of the AirCard W802S
personal hotspot, ensure that:
•The maximum number of Wi-Fi users has not been reached. (To determine
the number of connected Wi-Fi users and set the maximum, see "Wi-Fi Users
Information and Settings" on page 56).
•You're connecting to the correct Wi-Fi network (SSID), and you're using the
correct Wi-Fi password. If the Wi-Fi Password Reminder feature is enabled
(page 90), you can use it to display the SSID and Wi-Fi password on the
device LCD.
•Nobody has changed the name or password of the Wi-Fi network. If the Wi-Fi
Password Reminder feature is enabled (page 90), you can use it to display
the SSID and Wi-Fi password on the device LCD.
•Nobody is connected through the USB cable when Disable Wi-Fi when
connected via USB is selected.
•Your computer supports the type of Wi-Fi security that the network is set to
use.
Note: All the devices used with the AirCard W802S personal hotspot must support the
selected security type.
•Your computer supports Wi-Fi 802.11g (if Basic Rate is set, in Advanced
settings > Wi-Fi > Network, to 802.11b/g compatibility).
•Your computer has not been blocked, through MAC filtering. See "Specifying
Computers That Are Not Allowed to Access the Network" on page 91.
Tip: If some settings are preventing you from connecting to Wi-Fi, connect to the device
through the USB cable, and then change the settings. See "Requirements for a USB
Tethered Connection" on page 43 and "Making a Tethered Connection" on page 43.
![](/img.php?id=1412542&img=bg7a.png)
AirCard W802S User Guide
122 2400092
Cannot Display the Home Page
Your Web browser may display an error message when you try to display the
home page. The error message depends on your Web browser.
•"Internet Explorer cannot display the webpage" (Internet Explorer)
•"Oops! This link appears to be broken" (Google Chrome)
•"Safari can’t open the page" (Safari)
•"The connection has timed out" (FireFox)
Check the following:
•The device is turned on. See "Turning Your Device On" on page 33.
•You have established a connection to the device (through Wi-Fi or through the
USB cable).
•Ensure you're typing the correct address in the Web browser.
·Tr y http://<SSID>, where <SSID> is as displayed on the device LCD.
·If the home page is still not displayed, try http://192.168.0.1 or, if you're using
custom routing settings, replace "192.168.0.1" with the appropriate
IP address.
•The Web browser is a recent version, and Java-enabled. The following are
recommended:
·Internet Explorer (version 6.0 or higher)
·Mozilla Firefox (version 3.0 or higher)
·Google Chrome (version 2.0.172.28 or higher)
·Apple Safari (version 2.0 or higher)
•If your computer has other adapters (for example, Ethernet) connected to
other networks, disable or remove them from your computer.
•If Internet security software is running on your computer, disable it and see
whether the error message still occurs. Some firewall software may block
access to the home page.
•If DHCP is enabled on the device, ensure DHCP is enabled on your
computer. See "DHCP" on page 98.
•Check your Web browser settings.
a. Open the Control Panel in Windows.
b. Double-click Internet Options.
c. From the Security tab, restore the default settings.
d. From the Connections tab, select Never dial a connection.
e. From the Advanced tab, restore the default settings.
f. Close and reopen your Web browser.
•Disconnect the device from your computer (if you're using the USB cable).
Remove the battery from the device. Reinsert the battery.
If, after checking all of the above, you still cannot display the home page, consider
resetting the software to default settings. See "Resetting the Software to Default
Settings" on page 105.
![](/img.php?id=1412542&img=bg7b.png)
Resources
Rev 1 Oct.10 123
Cannot Connect to the 3G/4G Network
•Ensure your computer is connected to the device (through the USB cable or
Wi-Fi). See "How Do I Connect to Wi-Fi?" on page 112 or "Making a Tethered
Connection" on page 43.
•Try the tips in "Improving Signal Strength" on page 114.
•Check the WAN Mode setting (Advanced settings > WAN > Setup). For example,
if it's set to 4G only, you won't be able to connect if:
·You have 4G coverage, but you're roaming.
·You don't have 4G coverage.
•If you're roaming, ensure that 3G roaming is enabled.
In the Roaming Information window or from Advanced settings > WAN > 3G,
select Allow 3G Roaming.
Note: Roaming charges may apply.
•Check with <Carrier_Name> — a network or account problem may be
preventing your device from obtaining service.
Cannot Check for Updates
Ensure your device is connected to the power adapter or computer, through the
USB cable.
Note: If you’ll be using USB for data transfer (and not just for charging the device), you
must install the device driver. See "Making a Tethered Connection" on page 43.
Sounds are Enabled, but the Device Doesn't Generate
Any Sounds
Check that sounds are not turned off through the Mute switch on the device. See
"Mute Switch" on page 36.
![](/img.php?id=1412542&img=bg7c.png)
AirCard W802S User Guide
124 2400092
![](/img.php?id=1412542&img=bg7d.png)
Rev 1 Oct.10 125
7
7: Technical Specifications, Safety Infor-
mation, and Regulatory Information
Technical Specifications
LED Operation
See "Using the Power Button to Determine the Device State" on
page 34.
Radio Frequency and Electrical Specifications
Approvals FCC
Battery Size: 1800 mAh
Duration for full charge:
•AC charger: 1.5 hours
•PC USB cable: 3.6 hours
Charge life:
•4 hours under standard use
•3 hours of continuous use
Current Maximum: 1000 mA
Standby:
•48 mA (1xEV-DO/IS2000 hybrid mode)
•48 (WiMAX)
Transmit PCS: 1850 to 1910 MHz
Cellular: 824 to 849 MHz
WiMAX: 2495 to 2690 MHz
Receive PCS: 1930 to 1990 MHz
Cellular: 869 to 894 MHz
WiMAX: 2495 to 2690 MHz
GPS: 1575.42 MHz
![](/img.php?id=1412542&img=bg7e.png)
AirCard W802S User Guide
126 2400092
Software Specifications
CDMA (3G) specification IS-2000 Release 0
Data service IS-707A
WiMAX (4G) specification IEEE 802.16e-2005
Wi-Fi specification IEEE 802.11b
IEEE 802.11g
IEEE 802.11n
Wi-Fi security and
encryption protocols WEP Open & Shared
WEP-64
WEP-128
WPA-Personal TKIP & AES (Pre-Shared Key or WPA-
PSK)
WPA2-Personal TKIP & AES (WPA2-PSK)
WPA+WPA2-Personal (WPA+WPA2 PSK)
SMS (IS-637) Not supported
FAX Not supported
IOTA Supported
OTASP (IS-683A, IS-
683B, IS-683C) Supported
OTAPA Supported
PRL (Preferred Roaming
List) Supported
Authentication Supported
Voice Not supported
NAM Single
Position Location Standalone
TTY/Accessibility Not supported
Mobile IP Supported
Network protocols
(routing hardware) TCP, UDP, AR P, RARP, ICMP
VPN Pass-through of the following VPN types:
•PPTP
•IPSec
Tunneling of multiple VPN sessions simultaneously is
supported.
![](/img.php?id=1412542&img=bg7f.png)
Technical Specifications, Safety Information, and Regulatory Information
Rev 1 Oct.10 127
Environmental Specifications
Mechanical Specifications
Safety Information
Proper Battery Use and Disposal
Note: Improper battery use may result in a fire, explosion, or other hazard.
To ensure safe and responsible battery use:
•Do not open, disassemble, puncture, crush, bend, or shred.
•Do not expose to water or other liquids, fire, explosion, or other hazards.
•Use the battery only in the AirCard W802S personal hotspot.
•If using with a charger, use only the power adapter supplied with the device.
•Do not short circuit the battery.
•When replacing a battery, use the same model of battery that was supplied
with the device.
•Follow local regulations when disposing of a used battery.
•Avoid dropping the device or the battery. If dropped and you suspect damage,
take it to a service center for inspection.
Operating temperature -20 to +55°C
Storage temperature -25 to +60°C
Humidity 90%, non-condensing
Vibration 10-1000 Hz, 6G, 60 min/axis, 3 hrs total (non-operating)
Drop 1 m on concrete
Dimensions (W x L x H) 68 mm x 68 mm x 17.5 mm
Power button Supported
Headset jack Not supported
LED White
![](/img.php?id=1412542&img=bg80.png)
AirCard W802S User Guide
128 2400092
Regulatory Notices
The design of the AirCard W802S personal hotspot complies with U.S. Federal
Communications Commission (FCC) guidelines respecting safety levels of radio
frequency (RF) exposure for mobile devices, which in turn are consistent with the
following safety standards previously set by U.S. and international standards
bodies:
•ANSI / IEEE C95.1-1999, IEEE Standard for Safety Levels with Respect to Human
Exposure to Radio Frequency Electromagnetic Fields, 3kHz to 300 GHz
•National Council on Radiation Protection and Measurements (NCRP) Report
86, 1986, Biological Effects and Exposure Criteria for Radio Frequency Electromag-
netic Fields
•International Commission on Non-Ionising Radiation Protection (ICNIRP)
1998, Guidelines for limiting exposure to time-varying electric, magnetic, and electro-
magnetic fields (up to 300 GHz)
FCC ID: N7N-MHS802.
RF Exposure - The AirCard W802S personal hotspot has been tested for
compliance with FCC RF exposure limits in a portable configuration. At least
1.0 cm of separation distance between the AirCard W802S personal hotspot and
the user's body must be maintained at all times. This device must not be used
with any other antenna or transmitter that has not been approved to operate in
conjunction with this device.
Warning: (EMI) - United States FCC Information - This equipment has been tested and
found to comply with the limits for a Class B computing device peripheral, pursuant to
Parts 15 and 27 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
This device complies with Parts 15 and 27 of the FCC Rules. Operation is subject
to the condition that this device does not cause harmful interference.
![](/img.php?id=1412542&img=bg81.png)
Rev 1 Oct.10 129
Numerics
3G
3G panel of the WAN tab 94
3G Roaming Information window 55
activation failed 119
activation information, viewing 93
activation, initiate 49
configuration, resetting to default
settings 94
data transmission rates 26
improving network service, tips 115
lifetime data 82
Mobile Broadband Information window
54
overview 26
PRL version 68, 81, 94
service type 94
status 94
3G (time acquisition method) 110
3G Activation Required (alert) 49
3G Activation Required (LCD message) 120
3G Network Update Available (alert) 50
3G Only 54, 82
3G panel of the WAN tab 94
3G Preferred 54, 82
3G Roaming Information window 55
3G Roaming Settings 55
3G/4G Mobile Broadband Information
window 54
3G/4G Off 54, 82
4G
4G panel of the WAN tab 83
Base Station ID (BSID) 83
configuration, resetting to default
settings 94
connection status 83
coverage type (service type) 83
data transmission rates 26
lifetime data 82
Mobile Broadband Information window
54
network access provider (NAP-ID) 83
network service provider (NSP-ID) 83
overview 26
roaming support 112
4G Only 54, 82
4G Preferred 54, 82
802.11 standards supported 126
A
About panel of the Device tab 80
about this guide 27
AC charger (power adapter) 32
AC powered 57, 73
access to the network, configuring 90, 91
accessories 27
account information 68, 81
acquisition, time, method used for 109
Activate now 41
activating network service 41
Activation complete! 49
Activation Date 68, 81
Activation Required (alert) 49
Activation Status 68, 81
activation, 3G
3G Activation Required 120
3G Activation Required alert 49
date of original activation 93
failed 119
initiate 49
Active network 53, 82
Admin Login area of the home page 47
Admin Password 77
Admin Setup button 60
Administrator + Guest 62
administrator password
changing 77
forgotten; what do I do? 113
administrator, logging in as 47
Advanced Settings window 60, 78
AES 40, 88
alert
3G Activation Required 49
Alert window 55
audio, enabling/disabling 75
critical battery level alert 76
displaying 49
low battery 76
Network Update Available 50
SD Card Error 50
Software Update Available 51
Sounds panel of the Device tab 80
Index
![](/img.php?id=1412542&img=bg82.png)
AirCard W802S User Guide
130 2400092
Alert when (low battery) 76
Alert window 55
Allow 3G roaming 55, 94
Allow all in list (giving computers access to the
network) 90
Allow international access 55
allowing computers access to the network 90
Apple Safari 28
Application (port forwarding) 101
application notes 17
application updates 65
automatically check for updates 65
automatically log in
disabling for a specific computer 77
enabling 77
viewing list of computers set to automatically
log in 77
B
baby monitors 114
Backlight (LCD on the device)
brightness 74
turning off automatically 74
turning on or off 74
Backlight Settings 74
Base Station ID (BSID) 83
Basic panel of the Device tab 78
Basic panel of the Router tab 95
Basic Rate 85
battery
"Better battery life" setting 57, 73, 84
Battery Information and Settings window 57
charging 31
critical battery level alert 75, 76
high-capacity (purchased separately) 27
icon 57
installing 29
low battery alert 76
low battery, play sound 59
overview 29
proper use and disposal 127
specifications 125
tips on extending battery life 113
Battery Information and Settings window 57
Battery or USB powered 57, 73
Better battery life 57, 73, 84
billing cycle
data statistics 58
blacklist 85, 90
Block (block a computer's access to the Wi-Fi net-
work of the device) 56
Block all in list 90, 91
box contents 27
brightness of LCD 74
broadcast the SSID (Wi-Fi network name) 84
browser interface home page
See home page
browser interface updates 65
browsers supported 28
BSID (Base Station ID) 83
buttons
below the virtual device 61
top of home page 60
C
cannot connect to the 3G/4G network 123
cannot connect to Wi-Fi 121
cannot display the home page 122
care of your device 27
Carrier to Interference-plus-Noise Ratio (CINR) 54
CDMA
See 3G
cell phones 114
Center frequency 83
Certificate information 84
charger (power adapter) 32
charging the device 31
check for updates
automatically 65
manually 66
Check for updates now 66
Chrome browser 28
CINR (Carrier to Interference-plus-Noise Ratio) 54
Clear Log (connection history) 108
Clear Log (system events) 109
components of your device 26
Connect Automatically 55
Connect button 61
connect to Internet
alert 75, 80
cannot connect 123
improving 3G network service, tips 115
launching a connection 51
sharing your connection 52
![](/img.php?id=1412542&img=bg83.png)
Index
Rev 1 Oct.10 131
Connect/Disconnect 108
connected
how to tell you're connected to 3G/4G 112
icon 54
play sound when connected or
disconnected 59
Wi-Fi users information 56
connected computers, displaying a list of 92
Connected Users window 56
connecting the device to your computer
USB 43
Wi-Fi 112
Connecting to 3G/4G message 120
connection
ending 52
history log 108
improving 3G network service, tips 115
information, displaying 58
launching 51
lost (audio alert) - Internet Disconnected 75
settings 54, 82
sharing 52
state 53, 83
status, 3G 53
status, 4G 53, 83
Wi-Fi users information 56
Connection Error message 120
connection history
clearing 108
description 108
enabling logging 108
exporting 108
Connection Preferences 54
contents, package 27
contextual (field-level) Help 111
cordless phones 114
corporate network, accessing through VPN 113
coverage type (service type)
3G 94
4G 83
coverage type(s) available 54, 94
critical battery level alert 76
critical temperature alert 75
current, electrical (specification) 125
Customer Service, contacting 111
D
dark LCD 119
data statistics for the current connection session
58
data transferred 58, 82
data transmission rates 26
default settings
3G/4G configuration, resetting 94
software, resetting 106
software, resetting (through the reset button
on the device) 105
denying computers access to your network 91
Destination IP Address 104
device
information, viewing 68, 80
name (host name) 87
overview 25
device driver, installing 44
device name (host name) 92
Device tab
About panel 80
Basic panel 78
Display panel 79
Log panel 82
microSD card panel 79
Sounds panel 80
DHCP
clients, maximum number of 98
description 98
enabling 98
lease time 98
start and end address 98
Static IP Assignment List 99
DHCP IP Address Range 97, 98
DHCP Lease Time 98
DHCP Server 97
DHCP Static IP Assignment List 99
dimensions of device 127
Disable Wi-Fi upon USB-PC 93
Disable Wi-Fi when connected via USB 56, 93
Disconnect button 61
Display panel of the Device tab 79
displaying
home page 46
disposal of battery 127
DMZ
configuring 104
DMZ panel of the Router tab 104
![](/img.php?id=1412542&img=bg84.png)
AirCard W802S User Guide
132 2400092
enabling 104
DMZ panel of the Router tab 104
DNS Mode 100
DNS Relay 97
docking station (Home Crib) 27
document overview 27
dormant 94
download speeds 26
drawing of hardware 29
driver, installing 44
Drivers for (Windows, Mac OS X) 79
drop specification 127
duration for full charge 125
duration, session 58, 82
E
Ec/Io 54, 94
electrical specifications 125
Electronic Serial Number (ESN) 68, 81
email server, accessing 100
Enable SD Card 62
End (port, for port forwarding) 101
environmental specifications 127
ESN (Electronic Serial Number) 68, 81
Export Router Settings 107
exporting
connection history 108
settings 107
system event log 109
F
Failover wait time 83
failure, device startup
audio alert 75
FAQ (Frequently Asked Questions) 112
FCC (regulatory) notices 128
FCC ID 128
feedback 61
field-level (contextual) Help 111
Firefox browser 28
firewall software 122
firmware version
3G modem 68, 81
4G modem 69, 81
routing hardware component 68, 81
Wi-Fi 68, 81
firmware, upgrade from a file 67
folder name, microSD card 62
forgot administrator password 113
forgot Wi-Fi password 112
Forward Ports 103
Fragmentation Threshold 85
frequencies, transmit and receive 125
Frequently Asked Questions (FAQ) 112
FTP server, accessing 100
full charge 125
G
gaming, Internet 102
Get Started guide 27
Google Chrome 28
Guaranteed Update 65
Guest Password (for microSD card access) 62
Guest Username (for microSD card access) 62
H
hardware 29
Help button 61
Help files, updates 65
Help for Advanced Settings 111
help, getting
Customer Service, contacting 111
FAQ (Frequently Asked Questions) 112
tips 113
troubleshooting 118
website 111
Help, online 111
high-capacity battery 27
Home Crib 27
home page
buttons along the top 60
cannot display 122
description 45
displaying 46
logging in 47
vertical row of icons and text 52
virtual device 47
host name 87, 92
humidity specification 127
![](/img.php?id=1412542&img=bg85.png)
Index
Rev 1 Oct.10 133
I
icons
home page (vertical row of icons and text)
52
LCD 35
Import Router Settings 107
important information booklet 61
importing settings 107
improving signal strength 114
IMSI (International Mobile Station Identity) 68,
81, 94
information about your device 68, 80
installing the device 37
international access, allow 55
International Mobile Station Identity (IMSI) 68,
81, 94
Internet Connected 59, 75, 80
Internet Connection Information window 58
connection
lost (alert) 75, 80
Internet Disconnected 59, 75, 80
Internet Explorer 28
Internet Explorer cannot display the webpage
122
Internet gaming 102
Internet telephony 102
IOTA 126
IP address
assigning, based on MAC address 99
DHCP, range 97
DMZ computer 104
finding for a device 118
removing an address based on MAC
address 99
routing hardware 96
WWAN, of the device 58
IP Address (port forwarding) 101
K
knowledge base 118
L
LAN panel of the Router tab 96
Last user has joined 59
Last User Has Left 75, 80
LCD
brightness 74
dark 119
icons on LCD 35
not lit 119
timeout 74
turning off automatically 74
turning on or off 73
LCD Backlight 74
lease time, DHCP 98
LED (Power button on the device)
description 34
enabling 74
interpreting 34
location 29
lifetime data 82
lifetime of product
total data transferred 82
Link SSID and Host Name 87
list of connected computers, displaying 92
List of connected devices 92
Load 3G PRL 94
log
connection history 108
system events 108, 109
log in automatically
disabling for a specific computer 77
enabling 77
viewing list of computers set to automatically
log in 77
Log panel of the Device tab 82
logging in
automatically 77
steps to log in 47
login password
changing 77
forgotten; what do I do? 113
Longer Wi-Fi range 57, 73, 84
Low battery 59, 75, 80
low battery alert 76
low power mode (Standby Timer) 57
M
MAC (Media Access Control) filter 85, 90
MAC address
4G modem 69, 81
![](/img.php?id=1412542&img=bg86.png)
AirCard W802S User Guide
134 2400092
assigning an IP address based on MAC
address 99
finding for a device 117
Wi-Fi users 56
Mac device driver, installing 44
MAC filter 91
MAC Filter List 90, 91
MAC filter mode 86, 90
MAC Filter panel of the Wi-Fi tab 85
Mac OS X (driver, download) 79
maintenance of your device 27
manufacturer information 68, 81
Max DHCP clients 98
Max Number of Users 92
Max number of Wi-Fi users 92
Max Wi-Fi users 56
maximum number of Wi-Fi users 92
mechanical specifications 127
Media Access Control
See MAC address
MEID (Mobile Equipment Identifier) 68, 81
microSD card
accessing 62, 64
enabling 62
inserting 63
location of slot 29, 36
microSD Card panel of the Device tab 79
overview 36
removing from the device 63
SD Card Error (alert) 50
SD Card Information and Settings window 58
shared folder name 62
microSD Shared Folder Name 62
microwaves 114
Mini Window 48
Mobile Broadband Information window 54
Mobile Equipment Identifier (MEID) 68, 81
Mobile Station ID (MSID) 68, 81, 94
model information 68, 81
Mozilla Firefox 28
MSID (Mobile Station ID) 68, 81, 94
mute switch, location 36
N
NAI (Network Access Identifier) 94
NAP-ID (Network Access Provider ID) 83
network
3G, overview 26
4G Base Station ID (BSID) 83
4G network access provider (NAP-ID) 83
4G service provider (NSP-ID) 83
4G, overview 26
active network 53, 82
cannot connect 123
name, Wi-Fi (SSID) 86
network operator 82
protocols supported 126
Network Access Identifier (NAI) 94
network access provider, 4G (NAP-ID) 83
network access, configuring 90
network operator
4G (NSP-ID) 83
viewing 68, 81, 93
Network panel of the Wi-Fi tab 84
network service
3G, tips on improving service 115
activating 41
Network Time Protocol (NTP) 110
Network Update Available (alert) 50, 59
network, corporate, accessing through VPN 113
No filtering 90
no service
icon 54
not connected 54
notices
regulatory 128
NSP-ID (Network Service Provider ID) 83
NTP (Network Time Protocol) 110
O
Obtain an IP address automatically 98
On AC Power 74, 79
On Battery/USB Power 74
online games 100, 102
online Help
displaying 111
getting updates 65
Oops! This link appears to be broken 122
operating temperature 127
operator, network 68, 81, 93
original activation date 93
OTAPA 126
OTASP 126
overview of this document 27
![](/img.php?id=1412542&img=bg87.png)
Index
Rev 1 Oct.10 135
P
package contents 27
password reminder, Wi-Fi 90
password, administrator
changing 77
forgotten; what do I do? 113
password, Wi-Fi
changing 89
forgotten; what do I do? 112
overview 89
reminder 90
pay-as-you-go 95
performance, Wi-Fi, tips on improving 115
place for your device, tips 114
Plug and Play, Universal (UPnP) 96
Port Forward panel of the Router tab 100
port forwarding
description 100
disabling for an application 101
enabling 101
enabling for an application 101
Port Trigger panel of the Router tab 102, 103
port triggering
description 102
enabling 102
ports, adding 102
ports, removing 103
power adapter 32
Power button (on the device)
description 34
interpreting 34
location 29
Power Button LED field 74
Power Off button 48, 61
power settings
AC outlet, connected to 73
battery-powered 73
tips on extending battery life 113
USB powered 73
powering the device off 48
powering the device on 33
Preable 84
Preferred Roaming List (PRL) update
See PRL update
PRI version
3G component 68, 81
routing hardware 68, 81
PRL update
alert (update available) 50
load a file 94
loading a file 94
PRL version
3G modem 68, 81, 94
problems
See troubleshooting
Protocol (port forwarding) 101
Protocol (port triggering) 103
protocols, network, supported 126
Q
questions, frequently asked (FAQ) 112
R
radio frequency (RF) specifications 125
Realm 84
receive frequencies 125
Received (amount of data transferred) 58
recharging the battery 31
regulatory notices 128
Remember me 77
Remember me clients list 77
Remember me computers, view list of 77
reminder, Wi-Fi password 90
Remote Desktop, accessing 100
requirements
installation 28
USB 43
reset button
location 69
resetting the software to default settings 105
Reset Device to Factory Defaults button 95
resetting the 3G/4G configuration to default
settings 94
resetting the software to default settings
through the browser interface 106
through the reset button on the device 105
restarting the device 70
Restriction field 105
RF (Radio Frequency) specifications 125
roaming
3G Roaming Information window 55
4G support 112
enable or disable 94
international access, allow 55
![](/img.php?id=1412542&img=bg88.png)
AirCard W802S User Guide
136 2400092
roaming status 94
router
See routing hardware
Router IP Address 96
Router PRI Version 68, 81
Router setting reset
audio alert 59, 75
performing 106
Router tab
DMZ panel 104
LAN panel 96
Port Forward panel 100
Port Trigger panel 102, 103
routing hardware
firmware version 68, 81
IP address 96
play sound when routing hardware resets 75
PRI version 68, 81
resetting to default settings (through the reset
button on the device) 105
resetting to default settings (through the
software) 106
subnet mask 96
RSSI (signal strength)
improving 114
insufficient 119
viewing 53
RTS Threshold 85
Rx (receive) frequencies 125
S
Safari browser 28
Safari can’t open the page 122
SD Card error (alert) 50
SD Card Information and Settings window 58
Searching for Network 120
security
MAC filtering 85
network access, configuring 90
SPI (Stateful Packet Inspection) 96
tips 116
Wi-Fi 88
Security panel of the Wi-Fi tab 85
Sent (amount of data transferred) 58
server, accessing 100
service icon 54
Service Programming Code (SPC) 95
service type
3G 94
session duration 58, 82
Session total data 82
Set Guest Password (for microSD card access) 62
Set Guest Username (for microSD card access)
62
Set up my device 38
setting up the device 37
settings
exporting 107
importing 107
Setup panel of the WAN tab 82
shared folder name, microSD card 62
sharing your Internet connection 52
short text messaging (SMS) 126
Shorter Wi-Fi range 57, 73, 84
SID (System ID) 94
Sierra Wireless
knowledge base 118
Signal Quality window 53
signal strength
improving 114
insufficient 119
viewing 53
size of device 127
SMS 126
software
resetting to default settings 105
specifications 126
updates 65
Software Update Available (alert) 51, 59
Software Version 68, 81
sounds
enabling/disabling all (Mute switch) 36
enabling/disabling individually 75
Sounds panel of the Device tab 80
Sounds window 59
Source IP Address 104
SPC (Service Programming Code) 95
specifications
electrical 125
environmental 127
mechanical 127
radio frequency (RF) 125
software 126
speeds, download 26
SPI (Stateful Packet Inspection) 96
ssh support 113
![](/img.php?id=1412542&img=bg89.png)
Index
Rev 1 Oct.10 137
SSID (Wi-Fi network name)
broadcast 84
changing 86
description 86
Host Name, link to 87
SSID Broadcast 84
Standby Timer 57
Standby Timer on Battery or USB 79
Start (port, for port forwarding) 101
start day of the billing cycle, changing 58
Starts on day 58
startup failure, device (audio alert) 75
Stateful Packet Inspection (SPI) 96
Static IP Assignment List, DHCP 99
storage guidelines 27
storage temperature 127
subnet mask 96
Support button 60
support, contacting 111
Switchback wait time 83
System alerts 59, 75, 80
system events log
clearing 109
enabling 109
exporting 109
types of events included 108
System ID (SID) 94
system requirements 28
T
TCP/IP settings 98
technical support, contacting 111
telnet support 113
temperature specifications 127
temperature, critical (audio alert) 75
terminal sessions 113
tethered connection
making 43
requirements 43
See also USB
text messaging (SMS) 126
The connection has timed out 122
timeout
connection timeout (cannot display the home
page) 122
LCD 74
tips 113
TKIP/AES 40, 88
Total (amount of data transferred) 58
Total data 82
trademarks 17
transmission rates 26
transmit frequencies 125
transmitter power 83
Trigger Ports 103
troubleshooting
cannot connect to the 3G/4G network 123
cannot connect to Wi-Fi 121
cannot display the home page 122
general tips 118
TRU-Install 43
TTY 126
Turn Off Backlight 74
turning the device off 48
turning the device on 33
TVs 114
Tx (transmit) frequencies 125
Tx Power 83
U
Universal Plug and Play (UPnP) 95, 96
Update 3G PRL 83
Update 3G profile 83
Update Failed 121
Update firmware from file 67
updates
3G Network Update Available (alert) 50
automatically check 65
cannot check for 123
firmware, upgrade from a file 67
manually check 66
overview 65
PRL 50, 83
Software Update Available (alert) 51
UPnP (Universal Plug and Play) 96
usage guidelines for your device 27
USB
charging the device 31, 32
connecting the device to your computer
through USB 43
location 29
power settings 57
requirements 43
Wi-Fi, disabling when connected through
![](/img.php?id=1412542&img=bg8a.png)
AirCard W802S User Guide
138 2400092
USB 93
user ID, 3G network 94
Username and Password Security 62
V
Verbose System Event Logging 109
vertical row of icons and text 52
vibration specification 127
video conferencing 102
virtual device 47
Voice over Internet Protocol (VoIP) 102
VoIP (Voice over Internet Protocol) 102
VPN
accessing corporate network through 113
passthrough types supported 126
W
wait time
failover 83
switchback 83
WAN mode 82
WAN tab
3G panel 94
4G panel 83
Setup panel 82
warning (EMI) 128
warning (software settings reset) 105
warranty 61
Web browsers supported 28
Web server, accessing 100
website 111
Sierra Wireless 17
Welcome to Your Device window - Select an
Option 110
WEP 39, 88
whitelist 85, 90
Wi-Fi
alerts (user has joined, or left) 75, 80
cannot connect 121
channel 93
configuring, overview 86
connected computers, displaying list of 92
connecting to 112
longer Wi-Fi range 57, 73, 84
MAC Filter panel of the Wi-Fi tab 85
maximum number of users 92
network name (SSID) 86
Network panel of the Wi-Fi tab 84
password 89
Password Reminder 90
password, forgot 112
performance, tips on improving 115
security 88
security and encryption protocols supported
126
Security panel of the Wi-Fi tab 85
sounds when user joins or leaves 59
SSID (Wi-Fi network name) 86
USB tethered mode 93
Wi-Fi users information 56
Wi-Fi Channel 93
Wi-Fi Firmware Version 68, 81
Wi-Fi Passwordl 89
Wi-Fi Security Options window 39
Wi-Fi user has joined 59, 75, 80
Wi-Fi user has left 59, 75, 80
Windows (driver, download) 79
Windows device driver, installing 44
Windows XP
Wi-Fi performance, tips on improving 115
wireless speakers 114
WPA 40, 88
WPA2 40, 88
WWAN IP address of the device 58
X
XP, Windows
Wi-Fi performance, tips on improving 115
Y
Your device is now restarting (window) 40
![](/img.php?id=1412542&img=bg8c.png)