Unication Co GSPAGER1 GS Digital Voice Pager User Manual
Unication Co Ltd GS Digital Voice Pager
User manual
Any Time, Anywhere Unication is committed to Provide You the Best Solution G4 Voice Pager Supports P25 Radio Systems Now! Voice Pager Specially ecially Designed for Public Safety Advanced dvanced Radio Performan Performance Mission ission Critical Applications Application ional GSM Features Availa Optional Available ,I\RXKDYHDQ\UHTXLUHPHQWVSOHDVHFDOORXUWROOIUHHQXPEHU ZZZXQLFDWLRQFRP US-G4-FF-20150126-V1 INDEX Part A: G4 Specifications and Features Part B: Pager Overview B1 Pager Appearance B2 LCD Display B3 LED Introduction B4 Icon Introduction Part C: Operation Introduction C1 Initial Use C2 Pager Message Box C3 Function status C4 Voice Memo Box 11 C5 All Band Scan 12 C6 Function Setting 13 C7 Information 15 C8 Diagnostic 16 Part D: Warning and Important Notes 17 Part A. G4 Specifications and Features G4 Digital Trunking and Analog Voice Pager Specification & Feature A1 Operating Environment Operating Temperature Range -30 to + 60°C ESD (Electrostatic Discharge) contact Âą 8KV Air Âą 15KV Physical Operating Environment Analog (AM / FM) Digital (TDMA / FDMA) Available Modulation Type Digital and Analog identify modulation type and decode protocol automatically at the same time. (on same channels and same frequencies) Analog : 2-Tone / 5-Tone / MDC 1200 / CTCSS / CDCSS System Operating Environment DMR Conventional Available Support Protocol Digital P25 Conventional DMR Trunking VHF Band : 136MHz~174MHz Available Support Frequency Range UHF Band : 406MHz~512MHz 700 / 800 MHz Band : 764MHz~870MHz Apply to (Group) A2 Hardware Specification Mechanical Fixed and Carry Style Belt Clip Size 102 x 61 x 31.5 (L*W*H /mm) Weight (g) Without Battery(g) : < 220 ( g ) Dust / Waterproof According to specification of MIL-810 & Ingress Protection Rating is IP 67 Drop Protection Pad Special Requirement Operation Buttons Display UV Protection Fixed Function Key 13 Soft Key Navigation Key Power Volume Control Display Channel Switch Display Type LCD Saturation (grayscale / full color) full color Size (length x wide) 2.0 inches (30.6x40.8/mm) Number of Dots Characters & Length 220 x 176 9 lines x 22 characters Backlights Type (LED / EL ...) : LED LED LED Type (monochrome / multicolor) : red / green / blue / orange Power LED: No Brightness â Power off / Power on completed Part A. G4 Specifications and Features G4 Digital Trunking and Analog Voice Pager Specification & Feature A2 Hardware Specification LED LED Type (monochrome / multicolor) : red / green / blue / orange Blue - Power on / Connected with USB cable / Charging completed Flash Blue - Charging Message LED: No Brightness â No signal Red - Receiving voice call or data call Frequency Setting Channel Spacing Narrow Band :10/12.5k Number of Channels Hardware : 8 (do not need to switch via software) Software : 64 (8 Ch / 8 Zone) (switch via software) Total : 64 Wied Band : 20/25k Scan : 2.5k Frequency / Channel Specification Capcodes (Addresses) Frequency / Channel Specification of each channel Analog Digital Tone : Buzzer and speaker are the main device to be used as message alert and reminder Vibration : Motor and vibration speaker device are useful in meeting Tone and Vibration : Alert tone and vibration remind users as the same time Type of Alert Vibration then Tone : Vibrate first, then alert after few seconds Blacklight : Coloured backlights indicate users to identify the important level of each message, such as different colors, flashing backlights, different brightness LED : Different LED colors, flashing LED, different indicators Power Interface : 5V/1.5A DC Internal Power Supply / Battery input interface External Port Data recording streaming interface (PPS) Mini USB Wireless data streaming interface: (Bluetooth, WiFiâŚ) Power Supply Storage Memory Battery type : (Alkaline battery, Lithium Ion battery) 1. Lithium Ion Rechargeable Battery ďź3.7V / 2450mA 2. LiIon Rechargeable Batteryďź3.7V / 2450mA Battery Life : (Average bettery life at 5/5/90 duty cycle, 3 paging per day) > 24 hrs 2-Tone protocol continuous using 24 hrs per day Receiving 5 mins of 2-Tone voice message per hour Built-in Storage Memory: (including voice, text & saving time of data) Voice Text Others (Photos / ProfilesâŚ) A3 Electrical Characteristics Audio quality : Audio Receive input in 1KHz, then modulated by system Audio Performance SPL (12") : Alert tone loudness at 12 inches Hum & Noise Ratio > 34 dB Squelch Level < -57 dBw < 2 % (Electrical) < 3 % (Acoustic) < 3 % (Electrical) < 4 % (Acoustic) Audio Distortion Play Back Audio Distortion Alert Output 96 +/- 2 dB SPL Part A. G4 Specifications and Features G4 Digital Trunking and Analog Voice Pager Specification & Feature A3 Electrical Characteristics Audio Performance SPL (12") : Alert tone loudness at 12 inches Speech Output 94 +/- 2 dB SPL Frequency Stability : at the normal atmospheric temperature (25°C) Channel Spacing : at (25 °C) Alert Sensitivity 20 paging : at (25 °C) Alert Probability VS RF Level: at (25 °C) Message Sensitivity 20 paging : (Voice Pager @ 12dB SINAD) (Alpha Pager 3 Non-error) : at (25 °C) RF RX Performance Message Probability VS RF Level : (Voice Pager @ 12dB SINAD) (Alpha Pager 3 Non-error) : at (25 °C) Adjacent Channel Selectivity : at (25 °C) Co - Channal Rejection : at (25 °C) Intermodulation Rejection : at (25 °C) Low band VHF UHF Low band VHF UHF Low band VHF UHF Low band VHF UHF +/- 1 ppm 10/12.5/20/25 kHz âŚ-121dBm 100% @ Paging Sensitivity + 3 dB Low band ⌠4.0 uv/m VHF ⌠2.5 uv/m UHF ⌠3.5 uv/m Low band ⌠4.0 uv/m VHF ⌠2.5 uv/m UHF Low band ⌠3.5 uv/m VHF â§65 dB @ Âą25 KHz UHF Low band VHF UHF Low band VHF UHF > -8 dB ⧠70dB @ Alert ⧠70dB @12dB SINAD Low band Intermodulation High Level Third Order Rejection : at (25 °C) Spurious & Image Rejection : at (25 °C) Blocking Rejection : at (25 °C) VHF UHF Low band VHF ⧠35 dB @PS.+60dB ⧠70 dB UHF Low band VHF UHF ⧠90 dB A4 CERTIFICATION FCC : Part 15 Subpart B / ICES-003 CE : EN55022 / EN55024 / EN61000-3-2 / EN61000-3-3 Certification RoHS UL Division 1, Class I, Group C, D, / Class II, Group E, F, G MIL-STD B. Additional Function with unique accessaries Audio Amplification / Enhance receiving signal / LED Display / Relay / Remote control ( OTAC ) Part B. Pager Overview B1. Pager Appearance Front View Side View Rear View 12 13 15 16 14 Top View 11 10 Accessories Belt Clip USB Cable Lithium Ion Battery Pack NO. Description 10 11 12 13 14 15 16 LED Indicator Navigation Key Soft Key (K1~K4) Back Key (F2) Home Key (F1) Speaker Microphone Receive Antenna Channel Knob Play Key Power on/off & Volume Knob Reset Key Function Status on/off Key (S1) Mini USB Port Belt Clip Battery Cover Part B. Pager Overview B2. LCD Display Status Bar Text Area Tool Bar B3. LCD Introduction Power LED Message LED Power LED: NO. Entity Key Description Blue Power on process USB cable is connected to G4 and charging is completed. Flash Blue Charging Message LED: NO. Entity Key Red Description Receiving voice call or data call Part B. Pager Overview B4. Icon Introduction Status Bar Icon NO. Item Icon Description RF Strength RF signal strength. Out of Range Signal is out of range. Message Hint Unread message icon indication. Time Display Time display (24 hour clock). Off Duty Status Off duty status. On Duty Status On duty status. Bluetooth Bluetooth is activated. Bluetooth Headset Bluetooth earphone is connected. USB cable USB cable is connected. 10 Trunking Status Trunking registered. Trunking scanning. 11 12 Clock Alarm Clock alarm is activated. Battery Status The battery gauge indicator is located on the status bar and keeps you informed of the batery energy level. The five indicators are:100%, 75%, 50%, less 0% (flashing battery icon). Part C. Operation Introduction C1. Initial Use Install Battery Turn the screws and remove the battery cover. Insert the battery pack into G4. Replace the battery cover and and tighten the screws. Battery Charging Insert the battery so that the connector pins align with battery contacts of the G4. Power On G4 has its own customized lithium Ion battery, it can be charged by mini USB cable. After the battery installed , turn the volume knob clockwise to turn on G4. You will hear âclickâ sound and see the word of âLoadingâ on the display. USB power specification: 5V/1A Power on Standby Screen On the standby screen, G4 displays information on the current receiving mode. User Group Receiving Mode Zone/Channel Main Channel Name Band Duty Status (With Alarm) Receive Message G4 displays the information of the incoming call when receives a message. Protocol Receiving Channel Band Caller ID Caller ID Call Duration Part C. Operation Introduction Main Menu 1. In Standby Mode, press the âK1â soft key to enter the Main Menu. 2.Press the âHomeâ key to go back to Standby Mode. C2. Pager Message Box View and Manage Text Message Records in Message Box. 1. Enter Message Box: Use the Navigation Key to select Message Box in the Main Menu. 2. Operation: A. Use the Navigation Key to select Message. B. Press the "K1" Key to read highlighted message. C. Press the âK2â Key to lock/unlock highlighted message. A lock icon shows on a locked message. D. Press the âK3â Key to delete highlighted message. E. Press the âK4â to delete all messages. 3. Read Message: A. Use the Navigation Key to scroll the message. B. Press the âK1â Key to lock/unlock the message. Note: A locked item cannot be deleted. Part C. Operation Introduction C3. Function status Enter Function Status: Use the Navigation key to select Function Status in the Main Menu. Basic Operation: Use the Navigation Key to select features to set. 1. Select Zone: Press the "K1" Key to enter setting screen. Use the Navigation Key to select Zone and then press the âK1â Key to confirm. Press the âK2â Key to save. You can press the âK4â Key to check detailed information of highlighted Zone. 2. On Off Duty: Press the âK1â Key to enable or disable the feature. If On Off Duty is disabled, the speaker is muted when receiving messages. Part C. Operation Introduction 3. Bluetooth: Bluetooth Device: Press the "K1" Key to enable or disable the feature. Connect Bluetooth Earphone: Press the "K1" Key to start searching for the Bluetooth Earphone devices. Connect another Bluetooth Device: Press the âK1â to start searching for Bluetooth devices other than earphone. If only a Bluetooth device is found, the G4 starts pairing to the device. The G4 shows the pairing status on the screen. If there are 2 or more devices, use the Navigation Key to select device and press the âK1â Key to start pairing. Press the âK1â Key to stop Bluetooth pairing. 10 Part C. Operation Introduction C4. Voice Memo Box View and Manage Voice Memo in Voice Memo Box. 1. Enter Voice Record Box: Use the Navigation Key to select the Voice Memo Box in the Main Menu. 2. Record a New Voice Memo: If there is no voice memo, press the âK1â Key to start recording. A. Press the âK1â Key to pause. B. Press the âK4â Key to save the voice memo. C. Press the âK1â Key to set the voice memo as Alarm. D. Press the âF2â Key to back to Voice Memo box. 3. Voice Memo: View and manage the voice memos. Features page 1: A. Press the âK1â Key to play highlighted voice memo. B. Press the âK2â Key to set highlighted voice memo as Alarm. C. Press the âK3â Key to record a new voice memo. D. Press the âK4â Key to switch to features page 2. Features page 2: E. Press the âK1â Key to lock/unlock the highlighted item. F. Press the âK2â Key to delete the highlighted item. G. Press the âK4â Key to switch to features page 1. 4. Set Alarm: A. Use the Navigation Key to move. B. Press the âK1â Key to make highlighted value +5. C. Press the âK2â Key to make highlighted value +1. D. Press the âK3â Key to make highlighted value -1. E. Press the âK4â Key to save. 11 Part C. Operation Introduction C5. All Band Scan Set a range to scan, or view the scanned channel list. 1. Enter Voice Record Box: A. Use the Navigation Key to select All Band Scan in the Main Menu. B. Use the Navigation Key to select a feature, and press the âK1â key to enter. C. Press the âK1â Key to set the voice memo as Alarm. D. Press the âF2â Key to back to Voice Memo box. 2. Start a New Scan: Set scan range, band and frequency step. A. Use the Navigation Key to move. B. Press the âK1â Key to set the highlighted item. Use the Navigation Key to adjust numeric value. C. Press the âK4â Key to start scanning. D. Press the âK1â Key to stop scanning. 3. Active Frequency List: View and manage scanned channel list. A. Use the Navigation Key to move. B. Press the âK1â Key to monitor the highlighted channel. C. Press the âK2â Key to lock the highlighted channel. D. Press the âK3â Key to delete the highlighted channel. E. Press the âK4â to delete all scanned channels. 12 Part C. Operation Introduction C6. Function Setting View and manage pager basic function. Enter Function Status: Use the Navigation Key to select Function Setting in the Main Menu. Basic Operation: Use the Navigation Key to select function. Press âK1â Key to start setting. 1. Zone: Please refer C2-1 to get detailed information. 2. Alert Tone Volume: Use the âK1â Key to adjust the pager tone volume. A. Operation Allowed: Operation successed. B. Operation Succeed: Message received. C. Operation Failed: Message receiving failed. D. Message Arrived: Text message received. E. Alarm: Alarm volume 3. Backlight Mode&Level: Use the âK1â Key to adjust backlight mode. A. Mode: Select the backlight mode. There are 2 modes: âManualâ or âAutoâ. B. Manual: Night is low level, Day is medium and Glare is high level of backlight. 13 Part C. Operation Introduction 4. Backlight Dim Time: Adjust screen backlight dim time. A. Use the Navigation Key to move. B. Press the âK1â Key to make highlighted value +5. C. Press the âK2â Key to make highlighted value +1. D. Press the âK3â Key to make highlighted value -1. E. Press the âK4â Key to save. 5. Date & Time: Adjust Time of pager. A. Use the Navigation Key to move. B. Press the âK1â Key to make highlighted value +5. C. Press the âK2â Key to make highlighted value +1. D. Press the âK3â Key to make highlighted value -1. E. Press the âK4â Key to save. 6. Alarm Setting: Set up to 2 sets of Alarm. A. Use the Navigation Key to move. B. Press the âK1â Key to activate the Alarm. C. Press the âK4â Key to set. Alarm setting: A. Use the Navigation Key to move. B. Press the âK1â Key to make highlighted value +5. C. Press the âK2â Key to make highlighted value +1. D. Press the âK3â Key to make highlighted value -1. E. Press the âK4â Key to save. 7. Monitor Mode: Please refer to C2-4 for more detailed information. 14 Part C. Operation Introduction 8. Ring Mode: Select Ring mode. There are 5 modes: Tone: Tone only. Vibrate: Vibrate only. Silent: Mute mode. Vibrate then tone: Vibrate first then tone. Tone and Vibrate: Both. A. Use the Navigation Key to move. B. Press the âK1â Key to select. C. Press the âK4â Key to save. C7. Information View the Pager information. 1. Enter Information: Use the Navigation Key to select Information in the Main Menu. 2. Read: Language: Display language Language: Display language Version: Firmware version. SDRAM: SDRAM size. Protocol Model: Device model type. 15 Part C. Operation Introduction C8. Diagnostic View the radio signal strength. 1. Enter Message Box: Use the Navigation Key to select Message Box in the Main Menu. 2. Read Information: A. Rpt Name: Name of repeater B. RSSI(dBm): Radio Signal Strength Indicator. C. Protocol: Using Protocol of current channel. D. Frame Error: Received signal error radio. E. Others: Refer to channel setting. 16 Part D. Warning and Important Notes Notice : The changes or modifications not expressly approved by the party responsible for compliance could void the userâs authority to operate the equipment. Important Note : To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void userâs authority to operate the device. IC Note : The term âIC:â before the radio certification number only signifies that Industry Canada Technical specifications were met. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prĂŠsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisĂŠe aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioĂŠlectrique subi, mĂŞme si le brouillage est susceptible d'en compromettre le fonctionnement. Antenna : To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (EIRP) is not more than that required for successful communication. This device has been designed to operate with an antenna having a maximum gain of -2 dBi. Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms. 17
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Author : SSLIOU Create Date : 2015:12:02 17:10:52+08:00 Modify Date : 2015:12:02 17:10:52+08:00 Has XFA : No XMP Toolkit : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00 Metadata Date : 2015:12:02 17:10:52+08:00 Creator Tool : Adobe Illustrator CS4 Format : application/pdf Title : G4 說明書-0804 Creator : SSLIOU Document ID : uuid:496e9c6d-daf9-4489-91dc-ac663d80fd98 Instance ID : uuid:c01808fc-c57f-4e1b-96c1-a9b72fe6f693 Producer : Adobe Acrobat Pro 9.0.0 Page Count : 19EXIF Metadata provided by EXIF.tools