Wooyoung Telecom HLM151X 15.1" TFT LCD Monitor User Manual 1 of 2
Wooyoung Telecom Co., Ltd. 15.1" TFT LCD Monitor 1 of 2
Contents
- 1. User Manual 1 of 2
- 2. User Manual 2 of 2
User Manual 1 of 2
High Resolution TFT LCD Monitor Information to the user This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installa- tion. This equipment generates, uses and can radiate radio lrequency energy and, if not installed and used in accordance with the instructions, may cause harmlul interference to radio communications. However, there is no guarantee that interfer- ence Will not occur in a particular installation. lf this equipment does cause harmlul interference to radio or teleVision reception, with can be determined by turning the equipment ofl and on, the user is encouraged to try to correct the interference by one more oi the following measures - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. Warning Changes or modifications not expressly approved by the party responsible for com - pliance could void the user's authority to operate the equipment. MP-2000 User’ 5 Guide Information in this manual is subject to change without notice. © 2001 HANGILTELECOM CO.,LTD. All rights reserved. Reproduction in any manner whatsoever without the written permission of HANGIL TELECOM CO.,LTD. Is strictiy torbidden. HANGIL TELECOM CO.,LTD. shail not be iiabie tor errors contained herein or tor incidentai or consequentiai damages in connection With the furnishing, performance, or use of this material. HLM170M is registered trademarks oi HANGILTELECOM CO.,LTD.; Microsoft, Windows“ and Windows®NT are registered trademarks of Microsoft Corporation; VESA, DPMS and DDC are registered trademarks 01 Video Electronics Standard Association; All other product names mentioned herein may be the trademarks or registered trademarks of their respective owners. Contents Before Setting up Brief Specification of LCD Monitor - Precautions —————— Items 77777777777777777777777777777777777777777777777777777777777777777777777777777777777777777777777777777777777777777777777777777777777777 8 Setting up the LCD monitor 77777 Where is a good place to position the monitor? Please control Tilting Degree. Check before connecting the power cord and the signal cable !! How to connect the power cord and the signal cable to the LCD monitor 777777 Connecting Your LCD Monitor Plug & Play 777777 Warm-up Time ----- Adjusting The Monitor ------- The Function Control Buttons 77777 How to use function control button - How to use the Hot Key. - Main OSD Menu 777777 AUTO CONFIG POSlTION BRIGHTNESS/CONTRAST — 15 15 CLOCK/PHASE COLOR USER COLOR OSD POSITION 77777 INFORMATION ------ Appendix ..... Appendix A. Specifications 7777777 Appendix B. Display Modes ----- Appendix C. 15-pin D-Sub Connector Appendix D. DF‘MS Power Saving Mode Troubleshooting ...... 1 Before Setting up This is 15.1 inch TFT-LCD monitor. Before Setting up the LCD Monitor, Please this manual read help your understanding ck. Brief Specification of LCD Monitor —) - Resolution : 15.1 inch XGA (1024 X 768 @60Hz) - Color display : 262,144 colors - DPMS (Display Power Management Signaling) l Viewing angle : L/R 75'l75', U/D 55'l55' - Brightness : 2000d/m’ - OSD (On Screen Display) - Auto Configuration : Hot key I DDCt/ZB/ZBi : Plug & Play ' According to PC system, DDC 1/ZB may not be supported. If you meet Display Error Notice message, check your video card which compatibility with DDC. If you want to know more information, please Contact our service center. Check the voltige comsponds lo 1h: local eleelrlcal Do no! use Kctone type material (=x Acetone), Ethyl supply before pampering me AC power ppm, Alcohol, Toluene, Ethyl Acld or Methyl chloride, lo clenr me panel I! mlghl perrnnnenuy damage the panel. Keep it away from slaves, healers, fireplaces and other sources oi heal nnd mngnmv Navel use the damngzd AC power com Place vhe LCD mollllm on a solid Sudan: ll dropped. nhe scrml can be damaged ensiip Don'i pin your LCD monitor III a location with lush hlllludlly lnd dim Tempemure new'c Hnmrdny goalies; HLMlSlX Don't much me semen with a zcnle mul and pm The LCD mnnitorcnnsisls ofcleclxicll devices Inn: LCD monitor is damaged, Connie! immedinlely mu servlce semen The LCD mommy cm be «imaged eusuy by shack If you auu'z use the LCD manner 10! a long lime, unplug me LCD monitor Don't use your LCD murmur in under duet! sunlighl User Manual LCD Monitor ‘ \ AC Power Cord 15-pin D-Sub Signal Cable Notice Please make sure the following items are included with your monitor. If any items are missing, Contact your dealen Where is a good place to position the monitor? Place the LCD monitor on a solid and flat surface. If dropped. the screen can be damaged easily. Please control Tilting Degree. % You can see a supporting prop on the backside of the LCD moni- tor. Tilt the screen until you feel comfortable for working Tilting Degree (Up/Down) :+10/+30 Degree Check before connecting the power cord and the signal cable !! fl Turn off the PC power before connecting power cord and signal cable to the LCD monitor. HILMlSlX How to connect the power cord and the signal cable to the LCD monitor. fl AC Power Cord a 15-pin D-Sub Signal Cable Connecting Your LCD Monitor 1. First, you can connect the power cord to the LCD monitor and AC outlet. 2. You can connect the signal cable to the LCD monitor and the PC system. Plug & Play ) The adoption of the new VESA( Plug and Play solution eliminates complicated and time con- suming setup. It allows you to install your monitor in a Plug and Play compatible system without the usual hassles and confusion. Your PC system can easily identify and configure itself for use With your display. This monitor automatically tells the PC system its Extended Display Identification Data (EDID) using Display Data Channel (DDC) protocols so the PC system can automatically configure itself to use the flat panel display. Warm-up Time ) All LCD monitors need time to become thermally stable whenever you turn on the monitor. Therefore, to achieve more accurate adjustments for parameters, allow the LCD monitor to be warmed up for at least 20 minutes before making any screen adjustments.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No Modify Date : 2001:11:12 20:28:20+09:00 Create Date : 2001:11:12 20:28:00+09:00 Producer : Acrobat Distiller 4.0 for Windows Page Count : 11EXIF Metadata provided by EXIF.tools