3Si Security Systems AT170503A Asset Tracker User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3728135
Application ID	RbnXOvmYTcV6SsyTLYoJDA==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	72.05kB (900566 bits)
Date Submitted	2018-01-25 00:00:00
Date Available	2018-01-25 00:00:00
Creation Date	2018-01-24 10:25:31
Producing Software	Microsoft: Print To PDF
Document Lastmod	2018-01-24 10:25:31
Document Title	Microsoft Word - Q6KAT170503A_Integration_Manual.docx
Document Author:	WSierocinski

FCC ID: Q6KAT170503A
IC: 5043A-AT170503A
AT170503US Integration Manual
REGULATORY NOTICES
FCC
This device complies with the RF safety requirements as per FCC Part 1.1310, RF Exposure radiation limits
for the General Population / Uncontrolled Exposure.
This device shall be installed to maintain a separation distance of 20 cm from the general population.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by 3SI Security Systems could void the user's
authority to operate the equipment.
INDUSTRY CANADA
This device complies with the RF safety requirements for Canada as per RSS-102, RF Exposure radiation
limits for the General Population / Uncontrolled Exposure.
Cet appareil est conforme aux exigences de sécurité RF pour le Canada selon RSS-102, Limites de
rayonnement RF d'exposition pour la population générale / exposition incontrôlée.
This device shall be installed to maintain a separation distance of 20 cm from the general population.
Cet appareil doit être installé pour maintenir une distance de séparation de 20 cm par rapport à la
population générale.
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two
conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of
the device.
Cet appareil est conforme aux RSS exempts de licence d'Industrie Canada. L'opération est soumise aux deux
conditions suivantes:
(1) Cet appareil ne doit pas causer d'interférences; et
(2) Cet appareil doit accepter toute interférence, y compris les interférences susceptibles de provoquer un
fonctionnement indésirable de l'appareil.
FCC ID: Q6KAT170503A
IC: 5043A-AT170503A
1. Product description
1.1 General
AT170503US is a radio product designed by 3SI Security Systems to perform event monitoring
and location tracking services. To facilitate the data transfer to 3SI servers, this product has
provisions to host a wide range of LTE modems. The following information represents
AT170503US integration example with a Telit LTE modem ME866. Other modems may require a
layout modification (limited to U5 area only).
NOTE: only FCC and/or IC certified modems shall be used for the purpose of integration with
AT170503US.
1.2 Sub-sections
AT170503US contains the following sub-sections:
Sub-section
TYPE
GNSS
WiFi
Beacon
Beacon
Battery charger
Processor
receiver
transceiver
transceiver
transmitter
charger
system logic
FREQUENCY
[MHz]
1559 – 1610
2412 - 2462
2402 - 2480
216.475
N/A
40
COMMENT
Bluetooth
UHF
Optional use
Please refer to Q6KAT170503US Block Diagram exhibit for more information.
FCC ID: Q6KAT170503A
IC: 5043A-AT170503A
1.3 Interface definitions.
REF
J1
J2
J3
J4
J5
J6
J7
J8
J9
J10
P1
U5
SIGNAL
TYPE
DC
DC
Digital
DC
RF
RF
DC
DC
RF
RF
Digital
Digital
I/O
FUNCTION
CONNECTOR
COMMENT
input
input
Bi-directional
input
Bi-directional
Bi-directional
input
input
input
output
Bi-directional
Bi-directional
Auxiliary battery
DC power
Test port
Main battery connector
LTE modem diversity port
Modem transceiver port
DC power
Auxiliary battery
GNSS receiver input
UHF beacon diagnostics
Expansion connector
Hosted LTE modem
Header
Header
Header
Header
U.FL
U.FL
Micro USB
Header
U.FL
U.FL
Header
Solder pads
Optional battery connector
Optional
For factory use only
Internal battery
optional
External antenna
Primary charger source
Optional battery connector
External antenna
optional
Expanded functionality
xE866 family of LTE modems
manufactured by Telit
2. J1 External Battery connector (header pin)
2.1 J1 description
This connector is intended for connections to externally mounted batteries, when internal 3SI
battery is not required. (NOTE: all J1 signal lines are parallel with J4 and J8 connectors). For
details on battery operating voltage range refer to “Q6KAT1705093US Theory of Operation”
exhibit.
2.2 Modem pinout information
Pin
Signal
PLUS
MINUS
TS
I/O
Function
Positive battery terminal
Negative battery terminal
Thermistor
FCC ID: Q6KAT170503A
IC: 5043A-AT170503A
3. J2 DC Power Connector (header pin)
3.1 J2 description
This connector is intended for optional connection to external battery charger power sources
when connection through J7 is not required. The J2 signal lines are parallel with J7 lines.
3.2 J2 pinout information
Pin
Signal
PVBUS
GND
I/O
Function
Positive DC source terminal
Negative DC source terminal
4. J3 Test Port (Hirose 14-pin female)
4.1 J3 Description
This port is used for factory test and diagnostic purposes only. Integrators or users do not
require to access this port.
5. J4 Internal Battery connector (knife contacts)
5.1 J4 connector description
This connector provides connection to the internally mounted battery. The J4 signal lines are
parallel with J1 and J8 lines.
5.2 J4 pinout information (NOTE: all J8 signal lines are parallel to J1 and J8 connectors)
Pin
Signal
PLUS
MINUS
TS
I/O
Function
Positive battery terminal
Negative battery terminal
Thermistor
FCC ID: Q6KAT170503A
IC: 5043A-AT170503A
6. J5 Modem Diversity port (U.FL)
6.1 J5 connector description
This connector is reserved for future connection to modem diversity antenna input port.
Currently not placed in production. The characteristic impedance of this connector is 50
Ohms.
7. J6 Modem main antenna port (U.FL)
7.1 J6 connector description
This U.FL RF connector provides connection to modem transceiver input port via an RF
switch to an external LTE antenna. The characteristic impedance of this connector is 50
Ohms.
FCC ID: Q6KAT170503A
IC: 5043A-AT170503A
8. J7 DC power connector (micro USB)
8.1 J7 connector pin arrangement
8.2 J7 pinout information
Pin
Signal
VBUS
N/C
N/C
N/C
GND
I/O
Function
Power for charger
NOT CONNECTED
NOT CONNECTED
NOT CONNECTED
Ground
9. J8 auxiliary battery connector (header, 3 pin)
9.1 J8 connector description
J8 connector is designed be optionally placed to connect an auxiliary battery to this radio
product.
9.2 J8 pinout information (NOTE: all J8 signal lines are parallel to J1 and J4 connectors)
Pin
Signal
PLUS
MINUS
TS
I/O
Function
Positive battery terminal
Negative battery terminal
Thermistor
10. J9 GNSS input connector (U.FL)
10.1 J9 connector description
This connector allows attachment of an external GNSS active (i.e. amplified) antenna to the
AT170503US product. The expected range of incoming signals is 1559 – 1610 MHz. This
connector is rated for 50 Ohms characteristic impedance.
FCC ID: Q6KAT170503A
IC: 5043A-AT170503A
11. J10 beacon output connector (U.FL)
11.1 J10 connector description
J10 connector is intended to be used during the test and/or development phase and is
normally not installed in production.
12. P1 expansion connector (header, 14 positions)
12.1 P1 connector description
This port enables the system functionality expansion through addition of auxiliary sensors or
actuators.
12.2
P1 connector pinout information
Pin
10
11
12
13
14
Signal
GND
VBAT
EXP-INT
EXP-SPI-CLK
EXP-ENABLE
EXP-SPI-MISO
V1.8_uP
EXP-SPI-MOSI
EXP-I2C-SDA
EXP-SPI-CS
EXP-I2C-SCL
EXP-BATT-TS
VBAT
GND
I/O
I/O
I/O
I/O
I/O
I/O
I/O
Function
Ground
Battery power from expansion module
Expansion module interrupt
Expansion module generic interface control signal
Expansion module Enable signal
Expansion module generic interface control signal
1.8V IO power from device to Expansion module
Expansion module generic interface control signal
Expansion module generic interface control signal
Expansion module generic interface control signal
Expansion module generic interface control signal
Expansion module battery thermistor signal
Battery power from expansion module
Ground
13. U5 modem hosting socket (solder pads)
13.1 U5 description
U5 pad grid was designed to host LTE M2M xE866 modem family manufactured by Telit.
The modem selection is driven by the type of LTE network to support i.e. Verizon or AT&T.
All modems belonging to xE866 family share the same pinout and can be placed directly on
the reserved solder pads.
Other types of modems may require layout modifications (U5 area only).
FCC ID: Q6KAT170503A
IC: 5043A-AT170503A
13.2
U5 modem pin grid layout
FCC ID: Q6KAT170503A
IC: 5043A-AT170503A
13.3
U5 modem pinout information
13.3.1 USB HS 2.0 communications port
Pin
Signal
I/O
Function
Comment
E5
E6
USB_D+
USB_D-
I/O
I/O
USB differential Data (+)
USB differential Data (-)
NOT CONNECTED
NOT CONNECTED
13.3.2 Asynchronous Serial Port (USIF0) - Data + HW Flow Control
Pin
Signal
A4
C103/TXD
I/O
Function
Type
CMOS 1.8V
Serial data input (TXD) from
DTE
Serial data output to DTE
Input for (DTR) from DTE
Input for Request to send
signal (RTS) from DTE
Output for Clear to send
signal (CTS) to DTE
Output for (DCD) to DTE
A5
A2
A1
C104/RXD
C108/DTR
C105/RTS
B1
C106/CTS
B2
C109/DCD
A3
C107/DSR
Output for (DSR) to DTE
CMOS 1.8V
B3
C125/RING
Output for Ring (RI) to DTE
CMOS 1.8V
NOT CONNECTED
NOT CONNECTED
CMOS 1.8V
CMOS 1.8V
CMOS 1.8V
CMOS 1.8V
CMOS 1.8V
13.3.3 Asynchronous Auxiliary Serial Port (USIF1)
Pin
Signal
I/O
Function
Type
C1
TX_AUX
Auxiliary UART (TX Data to
DTE)
CMOS 1.8V
C2
RX_AUX
Auxiliary UART (RX Data
from DTE)
CMOS 1.8V
NOT CONNECTED
NOT CONNECTED
FCC ID: Q6KAT170503A
IC: 5043A-AT170503A
13.3.4 SIM card interface
Pin
Signal
I/O
C7
SIMVCC
B7
A7
A6
SIMRST
SIMCLK
SIMIO
SIMIN
I/O
Function
Type
External SIM signal – Power supply for the
SIM
1.8V Only
External SIM signal – Reset
External SIM signal – Clock
External SIM signal – Data I/O
Presence SIM input
CMOS 1.8
CMOS 1.8
CMOS 1.8
CMOS 1.8
13.3.5 Digital I/O
Pin
Signal
I/O
Function
Type
C5
GPIO_01
SIM_IN
I/O INT
Main Function: GPIO01 Configurable
GPIO Alternate Function: SIM_IN
CMOS 1.8V
C6
GPIO_02
SIM_IN
I/O INT
Main Function: GPIO02 Configurable
GPIO Alternate Function: SIM_IN
CMOS 1.8V
D6
GPIO_03
SIM_IN
I/O INT
General Purpose IO Alternate Function:
SIM_IN
CMOS 1.8V
D5
GPIO_04
SIM_IN
I/O INT
CMOS 1.8V
B5
GPIO_05
SIM_IN
I/O INT
B4
GPIO_06
ALARM SIM_IN
I/O INT
Main Function: GPIO04 Configurable
GPIO Alternate Function: SIM_IN
ANT-SELECT-EXT/INT#
Main Function: GPIO05 Configurable
GPIO Alternate Function 1: SIM_IN
NOT CURRENTLY USED
Main Function: GPIO06 Configurable
GPIO Alternate Function 1: ALARM
Alternate Function 2: SIM_IN
C4
GPIO_07
STAT_LED
SIM_IN
I/O INT
Main Function: GPIO07 Configurable
GPIO Alternate Function 1: STATLED
Alternate Function 2: SIM_IN
CMOS 1.8V
D8
VDDIO_IN
IO bus Supply input
Power
NOT CONNECTED
NOT CONNECTED
NOT CONNECTED
CMOS 1.8V
CMOS 1.8V
NOT CONNECTED
NOT CONNECTED
13.3.6 ADC and DAC
Pin
Signal
I/O
F4
ADC_IN1
AI
E4
DAC_OUT
AO
Function
Type
Analog/Digital converter input
NOT CONNECTED
Digital/Analog converter output
NOT CONNECTED
A/D
D/A
FCC ID: Q6KAT170503A
IC: 5043A-AT170503A
13.3.7 RF
Pin
Signal
I/O
Function
Type
G2
MAIN_ANT
I/O
LTE Main Antenna (50 ohm)
RF
13.3.8 Miscellaneous Functions
Pin
Signal
G4
G6
RESET*
VAUX
PWRMON
PSM_WAKE
PSM_STATUS
PSM_ENA_OUT
D3
E8
F8
I/O
Function
Type
Reset Input
1.8V stabilized output
Power ON monitor
PSM Wake Up
PSM Status
NOT CONNECTED
VBATT
Power
Analog
CMOS 1.8V
CMOS 1.8V
13.3.9 Power Supply
Pin
Signal
I/O
E2
VBATT
E0
VBATT_PA
E1
VBATT_PA
B0
D0
F0
G0
D1
F1
G1
D2
F2
C3
E3
F3
G3
F6
A8
G8
A11
G11
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
Function
Type
Main power supply
(Baseband)
Main power supply (Radio
PA)
Main power supply (Radio
PA)
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Power
Power
Power
Power
Power
Power
Power
Power
Power
Power
Power
Power
Power
Power
Power
Power
Power
Power
Power
Power
Power
FCC ID: Q6KAT170503A
IC: 5043A-AT170503A
13.3.10 Reserved
Pin
Signal
I/O
Function
A0
C0
G5
B6
D7
E7
F7
G7
B8
C8
A9
B9
C9
D9
E9
F9
G9
A10
B10
C10
D10
E10
F10
G10
B11
C11
D4
F5
F11
E11
D11
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
NOT CONNECTED
NOT CONNECTED
Optionally connected to MODEM-RING for NE866 PSM mode support
NOT CONNECTED
NOT CONNECTED
NOT CONNECTED
NOT CONNECTED
NOT CONNECTED
NOT CONNECTED
NOT CONNECTED
NOT CONNECTED
NOT CONNECTED
NOT CONNECTED
NOT CONNECTED
NOT CONNECTED
NOT CONNECTED
NOT CONNECTED
NOT CONNECTED
NOT CONNECTED
NOT CONNECTED
NOT CONNECTED
NOT CONNECTED
NOT CONNECTED
NOT CONNECTED
NOT CONNECTED
NOT CONNECTED
NOT CONNECTED
NOT CONNECTED
NOT CONNECTED
NOT CONNECTED
NOT CONNECTED
FCC ID: Q6KAT170503A
IC: 5043A-AT170503A
14. Integration procedure
Select a xE866 Telit modem that covers desired LTE bands
o the modem must be FCC and/or IC approved
Add the modem as U5 to AT170503US schematic
Perform on-board antenna optimization for the desired frequency range
o Antenna geometry (if required)
o Matching network (if required)
Perform EMC evaluation to validate continued FCC and IC compliance
15. Product labeling
Place on the product the label with the following content:
CONTAINS:
FCC ID: Q6KAT170503A, [MODEM FCC ID]
IC: 5043A-AT170503A, [MODEM IC ID]
16. Tune Up Information
The module tuning is performed during the manufacturing process. The integrated product requires no
further tuning. The user cannot access nor alter any tuning parameters.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : No
Warning                         : Info object (93 0 obj) not found at 898384

EXIF Metadata provided by EXIF.tools