ACA Digital WMIR-168 Mini PCI Module User Manual UVZWMIR 168 Manual

Download:
Mirror Download [FCC.gov]
Document ID	931065
Application ID	Xx5ZavSERQWfJyCpugbTjA==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	16.41kB (205119 bits)
Date Submitted	2008-04-21 00:00:00
Date Available	2008-04-21 00:00:00
Creation Date	2008-04-14 16:59:41
Producing Software	Acrobat Distiller 7.0 (Windows)
Document Lastmod	2008-04-14 16:59:41
Document Title	Microsoft Word - UVZWMIR-168_Manual.doc
Document Creator	PScript5.dll Version 5.2
Document Author:	Administrator

ACA‐Digital Corp.
WLAN 802.11 b/g User Manual
Model no.: WMIR‐168AG/E
(Ralink RT2561T)
ACA-DIGITAL
Integrated Baseband and MAC Solution
IEEE 802.11b/g WLAN
2008/3/29
ACA-Digital Corp.
Contents:
Contents:............................................................................................................................ 2
Introduction ...................................................................................................................... 3
Install the WLAN card .................................................................................................... 4
Install WMIR‐168AG (Ralink RT2561T) Driver........................................................... 5
Federal Communications Commission (FCC) Requirements ................................... 7
ACA-Digital Corp.
Introduction
The Wireless LAN Configuration Utility is a powerful application that helps you to
configure this WLAN card and monitor the statistics of the communication status.
Unlike the standard method of configuring the card via the operating system utili‐
ties, this application permits the dynamic modification of the configuration parame‐
ters while the card is operating. It also offers more configuration options.
We offer the Wireless LAN Configuration Utility for Windows® 98SE/Me/2000/XP.
Mini‐PCI WLAN equipment has been tested and found to comply with limits for a
Class B digital device, pursuant to Part 15 of the FCC rules. These limits are de‐
signed to provide reasonable protection against harmful interference in residential
installations.
This equipment generates, uses, and can radiate radio frequency energy, and if not
installed and used in accordance with the instructions, may cause harmful interfer‐
ence to radio communications.
ACA-Digital Corp.
Install the WLAN card
Release the screw from PC/NB
Find out the pre‐wired cable
Connect the cable with Mini‐PCI (“Main” connector)
Align and firmly plug the Mini‐PCI card into the slot.
Re‐place the cover to Device Secure the screw with a cross screwdriver.
ACA-Digital Corp.
Install WMIR‐168AG (Ralink RT2561T) Driver
The program will automatically pro‐
ceed with installing.
Select or create a program folder and
press “Next” to continue.
Press “Next” to continue
The program will automatically pro‐
ceed with installing.
Press “Yes” to continue.
Press “Browser” to change the folder
where setup will install files or press
“Next” to continue.
ACA-Digital Corp.
Press “Continue” to continue the
process.
Press “Finish” to complete the instal‐
lation
Insert the Wireless Card to slot of NB
and choose “Install the software
automatically (Recommended)” and
press “Next”.
ACA-Digital Corp.
Federal Communications Commission (FCC) Requirements
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installa‐
tion. This equipment generates uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful inter‐
ference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful in‐
terference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
‐Reorient or relocate the receiving antenna.
‐Increase the separation between the equipment and receiver.
‐Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
‐Consult the dealer or an experienced radio/TV technician for help.
INFORMATION:
This Transmitter must not be co‐located or operating in conjunction with any other
antenna or transmitter.
Any changes or modifications (including the antennas) made to this device that are
not expressly approved by the manufacturer may void the user’s authority to oper‐
ate the equipment.
End Product Labeling
This transmitter module is authorized only for use in devices where the antenna
may be installed such that 20 cm may be maintained between the antenna and users.
The final end product must be labeled in visible area with the following:
ACA-Digital Corp.
“Contains TX FCC ID: UVZWMIR‐168”
End Product Manual Information
The user manual for end users must include the following information in a promi‐
nent location “IMPORTANT NOTE: To comply with FCC RF exposure compliance
requirements, the antenna used for this transmitter must be installed to provide a
separation distance of at least 20cm from all persons and must not be co‐located or
operating in conjunction with any other antenna or transmitter.”
This device complies with part 15 of the FCC rules. Operation is subject to the fol‐
lowing two conditions
(1) This device may not cause harmful interference and
(2) This device must accept any interference received, including interference that
may cause undesired operation
IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop con‐
figurations or co‐location with another transmitter), then the FCC authorization is no
longer considered valid and the FCC ID can not be used on the final product. In
these circumstances, the OEM integrator will be responsible for re‐evaluating the
end product (including the transmitter) and obtaining a separate FCC authorization.
This device is intended only for OEM integrators under the following conditions:
The antenna must be installed such that 20 cm is maintained between the antenna
and users. As long as a condition above is met, further transmitter test will not be
required. However, the OEM integrator is still responsible for testing their
end‐product for any additional compliance requirements required with this module
installed (for example, digital device emissions, PC peripheral requirements, etc.).

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Distiller 7.0 (Windows)
Creator Tool                    : PScript5.dll Version 5.2
Modify Date                     : 2008:04:14 16:59:41+08:00
Create Date                     : 2008:04:14 16:59:41+08:00
Format                          : application/pdf
Title                           : Microsoft Word - UVZWMIR-168_Manual.doc
Creator                         : Administrator
Document ID                     : uuid:74c16e27-c4b0-4341-b778-70324b27bf39
Instance ID                     : uuid:e9790da1-a32e-4284-93bf-184833c57d74
Page Count                      : 8
Author                          : Administrator

EXIF Metadata provided by EXIF.tools