ADC Telecommunications F0689-011 InterReach Fusion 700 MHz (Upper C) , AWS MIMO HP User Manual FusionWideband IOR Issue7 Pages 128 240

ADC Telecommunications Inc. InterReach Fusion 700 MHz (Upper C) , AWS MIMO HP FusionWideband IOR Issue7 Pages 128 240

Contents

NOOF0689011 User Manual Part 2

Installing Expansion HubsInterReach Fusion Wideband Installation, Operation, and Reference Manual Page 129D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013 © 2013 TE Connectivity Ltd.3Ǥȋ͵͹ǤȌFigure37.Installing Directly to the Wall4ǤǡǤ1Dzdz͹ǦͳͺǤ2ǤǦǡǤǦǣ•POWERUL STATUSǤ•ǡUL STATUS Ǥ•E-HUB STATUSDL STATUS Ǥ•Ǥ3InstallinganOptionalCableManagerintheRack3PoweringontheExpansionHub
Installing Fusion Wideband Page 130 InterReach Fusion Wideband Installation, Operation, and Reference Manual© 2013 TE Connectivity Ltd D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013CAUTION! ObserveallFiberPortSafetyPrecautionslistedin“SafetyPrecautions”onpage109.PreparingtheFiberCables1͵ǤǦ͸ͲǤ2ǡǡǡǤ3ǯȀȋǦȌǤUsinganyotherconnectortypewillresultindegradedsystemperformanceandmaydamagetheequipment.ȋȀǯȀǡDzdzͳͶͷǡǤȌConnectingtheFiberCables12ǡǦǤǡǦȋȌǤIftheFiberJumperIsLabeledwith1or212DOWNLINKǤDL STATUSǤǡǤǤ21UPLINKǤUL STATUSǤʹͲǤǯE-HUB STATUSǤ3UL STATUSE-HUB STATUSȀǡǢʹͺ͹ͳʹ͸Ǥ3ConnectingtheFiberCablestotheExpansionHub
Installing Expansion HubsInterReach Fusion Wideband Installation, Operation, and Reference Manual Page 131D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013 © 2013 TE Connectivity Ltd.IftheFiberJumperIsColorͲCoded1DzdzDOWNLINKǤDL STATUSǤǡǤǤ2DzdzUPLINKǤUL STATUSǤʹͲǤǯE-HUB STATUSǤ3UL STATUSE-HUB STATUSȀǡǢʹͺ͹ͳʹ͸Ǥ1ǤǦǤ2ȋȌǤ3ǣ•••ȋȌ4ǤSTATUSǤ5ȋǡȌǡǦǤ6ǦǤ3Connectingthe75OhmCATVCables
Installing Fusion Wideband Page 132 InterReach Fusion Wideband Installation, Operation, and Reference Manual© 2013 TE Connectivity Ltd D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013•PORTȀǤǤ•UL STATUSǤ3TroubleshootingExpansionHubLEDsDuringInstallationTable88.TroubleshootingExpansionHubLEDsDuringInstallationDuringInstallationLED State Action Impact1Expansion Hub power is On and no RAUs are connectedPOWER Off Check AC power; make sure the Expansion Hub power-on switch is on; replace the Expansion Hub.The Expansion Hub is not powering on.PORT LEDs are on but didn’t blink through all states.Replace the Expansion Hub. The Microcontroller is not resetting properly; flash memory corrupted.PORT Flashing Red (6 PPM)Port unusable; replace the Expansion Hub when possible.Current sensor fault; do not use the port.UL STATUS Red, after power-up blinkReplace the Expansion Hub. The Expansion Hub laser is not operational; no uplink between the Expansion Hub and Main Hub.UL STATUS Red Check the Main Hub LEDs—refer to Step 2 in Table 87 on page 126.Use AdminBrowser to determine the problem.No communication with Main Hub.DL STATUS Red Check the downlink fiber for optical power; verify that the cables are connected to correct ports (that is, uplink/downlink)Check the Main Hub LEDs—refer to Step 2 in Table 87 on page 126.No downlink between the Expansion Hub and Main Hub.2Expansion Hub power is On and RAUs are connectedPORT Off Check the CATV cable. Power is not getting to the RAU.PORT Flashing Red (60 PPM)Test the CATV cable. If the cable tests OK, try another port. If the second port’s LEDs are Red/Off, replace the RAU. If the second RAU doesn’t work; replace the Expansion Hub.Power levels to RAU are not correct; communications are not established.If the second port works, flag the first port as unusable; replace EH when possible.PORT Red Use AdminBrowser to determine the problem.RAU is off-line.
Installing RAUsInterReach Fusion Wideband Installation, Operation, and Reference Manual Page 133D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013 © 2013 TE Connectivity Ltd.INSTALLINGRAUSCAUTION! InstallRAUsinindoorlocationsonly.DonotconnectanantennathatisinstalledinanoutdoorlocationtoanRAU.Foroutdoorinstallations,aprotectiveenclosureisrequired.NOTE: Thefollowingproceduresassumethatthesystemisnewfromthefactoryandthatithasnotbeenprogrammedwithbands.IfyouarereplacingcomponentsinapreͲinstalledsystemwitheithernewunitsorunitsthatmayalreadybeprogrammed(forexample,reͲusingunitsfromanothersystem),referto“ReplacingFusionWidebandComponents”onpage175.Ǥ•ͺͲͲͺͷͲȀͳͻͲͲͺͲͲͺͷͲǤDzͺͲͲȀͺͷͲdzͳ͵ͶǤ•ǡǡǡǡǡǡǤȋǡǡǡȌͶ͓͸Ǥ͹ǤǤ•ȋǡǡǡȌǤ•ǣ–͹͸ȋ͵ǤȌǤ–Ǥ–ȋȌǤǯǤLocationǤǡǤ3InstallingRAUs3InstallingPassiveAntennas
Installing Fusion Wideband Page 134 InterReach Fusion Wideband Installation, Operation, and Reference Manual© 2013 TE Connectivity Ltd D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013800/850MHzIsolationRequirementsǡǦǦǤǡǦǤǡǤǤͺͲͲͻͲͲȋǣͺͷͳȂͺ͸ͻȀǣͺͲ͸ȂͺʹͶǣͻ͵ͷȂͻͶͳȀǣͺͻ͸ȂͻͲʹȌǡͺͷͲȋǣͺ͸ͻȂͺͻͶȀǣͺʹͶȂͺͶͻȌǤǡͺͲͲȀͻͲͲͺͷͲǡȋȌȋȌǤ͵ͺǡǤFigure38.800/850 MHz SpectrumǦȋȌͺͲͲȀͻͲͲͺͷͲǦǦǤǤFigure39.Fusion Wideband 800/850/1900 MHz RAU Antenna Placement Guideline824 849 851 869 894 896 - 902800/iDEN Uplink 850 Cellular Uplink 800/iDEN Downlink 850 Cellular Downlink 900/iDEN UplinkBand 1800 MHzBand 2/3850/1900 MHz>d
Installing RAUsInterReach Fusion Wideband Installation, Operation, and Reference Manual Page 135D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013 © 2013 TE Connectivity Ltd.800MHziDENDownlinkand850MHzCellularUplinkʹȋͺͷͳȂͺͶͻȌͺͲͲͺͷͲǤǡͺͲͲͺͷͲǤǡͺͲͲͺͷͳͺͷͲȋȌǤǡǣ•ǦͺͲͲδǦͻͲ•ͺͲͲδȂ͵ͲȋͶǡǦǡȌǡȋͳȌ͸ȂͻǤ850MHzCellularDownlinkand900MHziDENUplinkʹȋͺͻ͸ȂͺͻͶȌͺͷͲͻͲͲǤǡͺͷͲͻͲͲǤǡͺͷͲͺͻͶͻͲͲǤǡǣ•ǦͺͷͲδǦͻͲ•ͺͷͲδȂ͵Ͳȋ͸ǡǦǡȌǡȋʹȌͺǦͳͶǤǦͺͷͳͻǦͳǦͺͲͻͲͳͻǦʹͺͳͶǤǦǤCAUTION! FirmlyhandͲtightentheNconnector–DONOToverͲtightentheconnector.3ConnectingtheAntennatotheRAU
Installing Fusion Wideband Page 136 InterReach Fusion Wideband Installation, Operation, and Reference Manual© 2013 TE Connectivity Ltd D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 20131ǤǦǤ2͹ͷǦ͹ͷǤ3ǣ•••ȋȌ4ǤǤǡǤǦǣ•LINKǤ•ALARMǡʹͲǡǤ5ȋȌǢǦǤ6ǦǤ3ConnectingtheCATVCable
Installing RAUsInterReach Fusion Wideband Installation, Operation, and Reference Manual Page 137D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013 © 2013 TE Connectivity Ltd.TroubleshootingUsingRAULEDsDuringInstallationLINKͻͲǤALARM ǤTable89.TroubleshootingRAULEDsDuringInstallationDuringInstallationLED State Action ImpactThe RAU is connected to the Fusion Wideband Expansion Hub, which is powered onLINK Off Check CATV cable. No power to the RAU.ALARM OffLINK Green • Check CATV cable• Check the Main Hub LEDs—refer to Step 2 in Table 87 on page 126.• Use AdminBrowser to determine the problem.The RAU is off-line.ALARM RedLINK Red from green, after cables are connected for 60 seconds• Check CATV cable.• Check the Hub LEDs.• Use AdminBrowser to determine the problem.No communications between the RAU and the Hub.ALARM Red
Installing Fusion Wideband Page 138 InterReach Fusion Wideband Installation, Operation, and Reference Manual© 2013 TE Connectivity Ltd D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013CONFIGURINGTHEFUSIONWIDEBANDSYSTEMǡǤǤǡAdminBrowserUserManualȋǦ͸ʹͲ͸Ͳ͹ǦͲǦʹͲȌǡȀǤNOTE: Thefrequencybandsshouldautomaticallybesetonpowerupandthisstepshouldnotberequired.NOTE: CrossoverEthernetcablewithmaleconnectorsrequired.NOTE: Thefollowingproceduresassumethatthesystemisnewfromthefactoryandthatithasnotbeenprogrammedwithbands.IfyouarereplacingcomponentsinapreͲinstalledsystemwitheithernewunitsorunitsthatmayalreadybeprogrammed(forexample,reͲusingunitsfromanothersystem),referto“ReplacingFusionWidebandComponents”onpage175.1ǤCAUTION! MakesuretheHubisgroundedthroughthegroundlugontheACpowerandtheframegroundlugasrequired.ThewarrantydoesnotcoverdamagecausedwhenanungroundedHubispoweredon.2Ǥ3Ǥ4ǤǤȋȌǡǤSTATUSͻͲǤǯǤʹͲǤ5ǦȀRJ-45 100-BASE-T ǯǤ3ConnectingthePCtotheMainHubtoRunAdminBrowser
Configuring the Fusion Wideband SystemInterReach Fusion Wideband Installation, Operation, and Reference Manual Page 139D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013 © 2013 TE Connectivity Ltd.1ȀȀRJ-45ǯǤ2Ǥ3ǣ•ForWindows2000:aǦMy Network PlacesPropertiesǤbInternet Protocol (TCP/IP)PropertiesǤǤ•ForwindowsXP:aStart>Settings>NetworkConnections>LocalAreaConnectionǤǤbThis connection uses the following itemsǡInternet Protocol (TCP/IP)PropertiesǤ3ProgrammingtheMainHubUsingAdminBrowser
Installing Fusion Wideband Page 140 InterReach Fusion Wideband Installation, Operation, and Reference Manual© 2013 TE Connectivity Ltd D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 20134ǡǡǡǤǦǤ5Use the following IP addressǤ6IP addressͳͻʹǤͳ͸ͺǤͲǤͳͲͳ7Subnet maskʹͷͷǤʹͷͷǤʹͷͷǤͲ8Default gateway ͳͻʹǤͳ͸ͺǤͲǤͳ9OKǤǤǡYesǤUsingAdminBrowserǡǣ1Ǥ2ǣHttps://192.168.0.1003GoǤ4ǡǣoperatorǡǣpasswordǤ5ǡǡǣoperatorpasswordǤ6SystemConfigurationSetDate/TimeǤǤ7SetDate/TimeǤǤ
Configuring the Fusion Wideband SystemInterReach Fusion Wideband Installation, Operation, and Reference Manual Page 141D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013 © 2013 TE Connectivity Ltd.8Install/ConfigureSystemǤǤ9ǡLabelǤǤ͵ʹǤFusionǡǤ10 Ǥǣ•Ǥ•Ǥ•Ǥ•ǤǡǦǦǤǡǢǡǤȋȌǤǡǡǤ
Installing Fusion Wideband Page 142 InterReach Fusion Wideband Installation, Operation, and Reference Manual© 2013 TE Connectivity Ltd D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 201311 Ǥ12 Bandsǡǣ•ǤǤ•ǡShutdownǤǤ•UplinkDownlinkǤͳǤ•UplinkAutomaticLevelControlSingleMultipleȋȌǤ13 FORWiMAXINSTALLATIONSONLYǣǤ
Configuring the Fusion Wideband SystemInterReach Fusion Wideband Installation, Operation, and Reference Manual Page 143D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013 © 2013 TE Connectivity Ltd.ǡǣ•ǣǣMIMOȋǦȌSISOȋǦȌǤDzdzǤ•ǤͳʹǤNOTE: InMIMOmode,thefrequenciesarethesame.Thesystemcanbeconfiguredtosupport2ͲSISOradios,oneperband,acrossany30MHzwithintheWiMAXband.•ǦǤǦǦǤǣ–StaticǦSelected:ǤǦǤȋDzʹͻǡͳͺdzǤȌǡǤ–StaticǦAuto:ǡǤȋDzǦdzȌ•ǦǤǣ–Synchronized:ǡǤǡǤ–Unsynchronized:ǡǤȋDzdzȌ•Reference:Ǥ•ǡǤǤ•ǦǤͳǤ•ǦDzdzDzdzǤȋDzǤdzȌ14 Ǥ
Installing Fusion Wideband Page 144 InterReach Fusion Wideband Installation, Operation, and Reference Manual© 2013 TE Connectivity Ltd D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 201315 Input/OutputAlarmsǡǣ•Ǥ•ǦǤȋDzǤdz•Ǥ16 ǡInstall System ǤǢǡǡǢǢǢǤǣǡǤ17 ȋǡȌǤCAUTION! DonotexceedthemaximuminputRFpower(1Watt)totheFusionWidebandMainHub.ExceedingthelimitcouldcausepermanentdamagetotheHub.CAUTION! OnlycarriersandtheirapprovedinstallersorTEͲauthorizedinstallersareallowedtoconnecttotheRFsource.SeriousdamagetotheequipmentcanoccurifitisoverͲdriven.ǤǡǤ18 ȀǤNOTE: TEequipmentisdesignedtooperateinthelicensedfrequencybandsofmobileoperators.IntheUSA,theEU,andmostcountriesthisequipmentmayonlybeusedbythelicensee,hisauthorizedagentsorthosewithwrittenauthorizationtodoso.Similarly,unauthorizeduseisillegal,andsubjectstheownertothecorrespondinglegalsanctionsofthenationaljurisdictioninvolved.OwnershipofTEequipmentcarriesnoautomaticrightofuse.Indicates that the band is correctly set on the Main Hub.Indicates that the band is correctly set on the Expansion Hub.Indicates that communications are OK.
Splicing Fiber Optic CableInterReach Fusion Wideband Installation, Operation, and Reference Manual Page 145D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013 © 2013 TE Connectivity Ltd.SPLICINGFIBEROPTICCABLEȀǤǡǡȀǡǤǣǦȋͶͲͳ͵Ǧ͵ȌǦȋͶͲͳʹǦ͵ȌǤǤǤǤǤȋͲǤͲͷȌȋȌǤǤNOTE: Thefollowingproceduresassumethatthesystemisnewfromthefactoryandthatithasnotbeenprogrammedwithbands.IfyouarereplacingcomponentsinapreͲinstalledsystemwitheithernewunitsorunitsthatmayalreadybeprogrammed(forexample,reͲusingunitsfromanothersystem),referto“ReplacingFusionWidebandComponents”onpage175.OptionA:FusionWidebandSplicetheFiberͲOpticCabletotheSC/APCPigtail1ȋǡǦǦȌǤ2ȀǤ3ǡǡǡDzdzȂǤ4Ǥ5ǦǤ6ǯǤ7Ͷ͸ȀǤ8Ǥ9ǯǤ10 ͲǤͳͲǤ11 Ǥ3FusionWidebandSplicingofFiberandPigtail
Installing Fusion Wideband Page 146 InterReach Fusion Wideband Installation, Operation, and Reference Manual© 2013 TE Connectivity Ltd D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 201312 ǯǤ13 Ǥ14 ǡǡǯǤ15 ǡȀǤOptionB:FusionWidebandSplicetheFiberͲOpticCabletotheSC/APCPigtail1ȋǡǦǦȌǤ2ȀǤ3ǡǡǡDzdzȂǤ4Ǥ5ǦǤ6ǯǤ7͵͸ȀǤ8Ǥ9ǯǤ10 ͲǤͳͲǤ11 Ǥ12 ǯǤ13 Ǥ14 ǡǡǯǤ15 ǡȀȀǤ16 ȀȀǤNOTE: Forinformationontroubleshooting,see“Maintenance,Troubleshooting,andTechnicalAssistance”onpage181.
Interfacing the Fusion Wideband Main Hub to an RF SourceInterReach Fusion Wideband Installation, Operation, and Reference Manual Page 147D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013 © 2013 TE Connectivity Ltd.INTERFACINGTHEFUSIONWIDEBANDMAINHUBTOANRFSOURCECAUTION! OnlyTEpersonnelorTEͲauthorizedinstallationpersonnelshouldconnecttheFusionWidebandMainHubtoitsBandassociatedbasestationorrepeater.ExceedingthemaximuminputpowercouldcausefailureoftheFusionWidebandMainHub(referto“RemoteAccessUnitConnectors”onpage57formaximumpowerspecifications).Ifthemaximumcompositepoweristoohigh,attenuationisrequired.NOTE: Thefollowingproceduresassumethatthesystemisinstalledandhasbeenprogrammedwithbands.ConnectingaSingleFusionWidebandMainHubtoanRFSourceǡͳǡʹǡ͵ǤǤCAUTION! OnlyTEpersonnelorTEͲauthorizedinstallationpersonnelshouldconnecttheFusionWidebandMainHubtoabasestationorrepeater.ExceedingthemaximuminputpowercouldcausefailureoftheFusionWidebandMainHub(referto“RemoteAccessUnitConnectors”onpage57formaximumpowerspecifications).Ifthemaximumcompositepoweristoohigh,attenuationisrequired.CAUTION! TheUPLINKandDOWNLINK portscannothandleaDCpowerfeedfromthebasestation.IfDCpowerispresent,aDCblockmustbeusedorthehubmaybedamaged.3ConnectingaFusionWidebandMainHubtoanInͲBuildingBTS
Installing Fusion Wideband Page 148 InterReach Fusion Wideband Installation, Operation, and Reference Manual© 2013 TE Connectivity Ltd D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013ConnectingaSimplexBaseStationtoaFusionWidebandMainHubRFBand1ǦǦǤ2ǦǦDOWNLINKͳǡʹǡ͵Ǥ3ǦǦǤ4ǦǦUPLINKͳǡʹǡ͵ǤFigure40.Simplex Base Station to a Fusion Wideband Main Hub SimplexBase StationBand 3Band 1 Band 2 Band 3UL1 UL2 UL3AlarmsDL1 DL2 DL3AC PowerN-male to N-malecoaxial cableT1/E1 toMobileSwitchingCenterInsert attenuator(if needed)NOTE: This applies to Band 1, Band 2, and Band 3.
Interfacing the Fusion Wideband Main Hub to an RF SourceInterReach Fusion Wideband Installation, Operation, and Reference Manual Page 149D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013 © 2013 TE Connectivity Ltd.ConnectingaDuplexBaseStationtoaFusionWidebandMainHubNOTE: Whenconnectingtoaduplexbasestation,useacirculatororduplexerbetweenitandtheFusionWidebandMainHub.NOTE: YoucaninsertattenuatorsbetweenthecirculatororduplexerandHubasneeded.1ǦǦǤ2ǦǤ3ǦǦDOWNLINKͳǡʹǡ͵Ǥ4ǦǤ5ǦǦUPLINKͳǡʹǡ͵Ǥ6Ǧ  ǤFigure41.Duplex Base Station to a Fusion Wideband Main Hub DuplexBase StationBand 1 Band 2 Band 3UL1 UL2 UL3AlarmsDL1 DL2 DL3AC PowerN-male to N-malecoaxial cableT1/E1 toMobileSwitchingCenterInsert attenuator(if needed)NOTE: This applies to Band 1, Band 2, and Band 3.CirculatorN-male to N-malecoaxial cable
Installing Fusion Wideband Page 150 InterReach Fusion Wideband Installation, Operation, and Reference Manual© 2013 TE Connectivity Ltd D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013CAUTION! OnlyTEpersonnelorTEͲauthorizedinstallationpersonnelshouldconnecttheFusionWidebandMainHubtoabasestationorrepeater.ExceedingthemaximuminputpowercouldcausefailureoftheFusionWidebandMainHub(referto“RemoteAccessUnitConnectors”onpage57formaximumpowerspecifications).Ifthemaximumcompositepoweristoohigh,attenuationisrequired.ȀǡͶʹͳͷͲǤFigure42.Connecting a Fusion Wideband Main Hub to Multiple Base Stations3ConnectingaFusionWidebandMainHubRFBandtoMultipleBTSsBand 1 Band 2 Band 3UL1 UL2 UL3AlarmsDL1 DL2 DL3AC PowerInsert attenuators(if needed)2 x 1 PowerCombiner/SplitterN-male to N-malecoaxial-jumper cablesbetween Combiner/Splitter andFusion Main Hub’s Uplink Portfor each on Band 1, Band 2, or Band 32 x 1 PowerCombiner/SplitterN-male to N-malecoaxial-jumper cablesbetween Combiner/Splitter andFusion Main Hub’s Downlink Portfor either Band 1, Band 2, or Band 3BTS 1UL DLBTS 2UL DL
Interfacing the Fusion Wideband Main Hub to an RF SourceInterReach Fusion Wideband Installation, Operation, and Reference Manual Page 151D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013 © 2013 TE Connectivity Ltd.CAUTION! TErecommendsthatyouusealightningarrestororsurgeprotectorinaroofͲtopantennaconfiguration.InsertthelightningarrestororsurgeprotectorbetweentheroofͲtopantennaandtherepeaterconnectedtotheFusionWidebandMainHubRFBand.1ǦǦǦǤ2ǦǦǤ3ǦǦǤ4ǦǦǤ5ǦǦǤ6ǦǦ1Ǥ7ǦǦ2Ǥ8ǦǦDOWNLINKͳǡʹǡ͵ǤȋǤȌ9ǦǦ3Ǥ10 ǦǦUPLINKͳǡʹǡ͵ǤFigure43.Connecting a Fusion Wideband Main Hub to a Roof-top Antenna3ConnectingaFusionWidebandMainHubtoaRoofͲTopAntennaBand 1 Band 2 Band 3UL1 UL2 UL3AlarmsDL1 DL2 DL3AC PowerAttenuator(optional)NOTE: This applies to Band 1, Band 2, and Band 3.N-male to N-malecoaxial cableRooftopAntennaN-male to N-malecoaxial cableGroundedSurge SuppressorRooftopAntennaCirculator1 2
Installing Fusion Wideband Page 152 InterReach Fusion Wideband Installation, Operation, and Reference Manual© 2013 TE Connectivity Ltd D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013ǤConnectingMultipleFusionWidebandMainHubstoanRFSourceȀǤȀǤCAUTION! OnlyTEpersonnelorTEͲauthorizedinstallationpersonnelshouldconnecttheFusionWidebandMainHubtoabasestationorrepeater.ExceedingthemaximuminputpowercouldcausefailureoftheFusionWidebandMainHub(referto“RemoteAccessUnitConnectors”onpage57formaximumpowerspecifications).Ifthemaximumcompositepoweristoohigh,attenuationisrequired.1ǣ2ȀǦǦǣaȀUPLINKbȀDOWNLINK3ȀǣaǯUPLINK ȋͳǡʹǡ͵ȌȀbǯDOWNLINK ȋͳǡʹǡ͵ȌȀcǯUPLINK ȋͳǡʹǡ͵ȌȀdǯDOWNLINK ȋͳǡʹǡ͵ȌȀNOTE: ConnectionsshouldnotcrossBands.Forexample,allBand1connectionsshouldbemadetothesamehybridpowercombiner/splitterconnectedtotherepeaterBTSthatmatchestheBand1frequency.3ConnectingaFusionWidebandMainHubtoFlexwaveFocus3ConnectingMultipleFusionWidebandMainHubstoaSimplexRepeaterorBTSQuantity Item2 hybrid power combiner/splitters—one for uplink and one for downlink (2x1 for two Fusion Wideband Main Hubs, 3x1 for three, 4x1 for four, and so on)1 N-male to N-male coaxial jumper cable between each power combiner/splitter and the base station2 N-male to N-male coaxial jumper cables between each power combiner/splitter and each Fusion Wideband Main Hub RF Band (either Band 1 or Band 2)
Interfacing the Fusion Wideband Main Hub to an RF SourceInterReach Fusion Wideband Installation, Operation, and Reference Manual Page 153D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013 © 2013 TE Connectivity Ltd.4ȄǡǤ5ǤThewarrantydoesnotcoverdamagecausedwhenanungroundedHubispoweredon.NOTE: Usea50ohmterminatoronanyunusedpowercombiner/splitterports.ͶͶǤͺͳ͸ǤFigure44.Connecting Two Fusion Wideband Main Hub’s RF Band Ports to a Simplex Repeater or Base Station Band 1 Band 2 Band 3UL1 UL2 UL3AlarmsDL1 DL2 DL3AC PowerN-male to N-malecoaxial-jumper cablesbetween Combiner/Splitterand Fusion Main Hub’s Uplink Port for either Band 1,Band 2, or Band 32 x 1 PowerCombiner/Splitter2 x 1 PowerCombiner/SplitterN-male to N-malecoaxial-jumper cablesbetween Combiner/Splitter andFusion Main Hub’s Downlink Portfor either Band 1, Band 2, or Band 3Band 1 Band 2 Band 3UL1 UL2 UL3AlarmsDL1 DL2 DL3AC PowerN-male to N-malecoaxial-jumper cableto Repeater orBase StationN-male to N-malecoaxial-jumper cableto Repeater orBase Station
Installing Fusion Wideband Page 154 InterReach Fusion Wideband Installation, Operation, and Reference Manual© 2013 TE Connectivity Ltd D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013CAUTION! OnlyTEpersonnelorTEͲauthorizedinstallationpersonnelshouldconnecttheFusionWidebandMainHubtoabasestationorrepeater.ExceedingthemaximuminputpowercouldcausefailureoftheFusionWidebandMainHub(referto“RemoteAccessUnitConnectors”onpage57formaximumpowerspecifications).Ifthemaximumcompositepoweristoohigh,attenuationisrequired.1ǣ2ǦǦǤ3ȀǦǦȀǤ4ȀǦǦǣaǯUPLINK ȋͳǡʹǡ͵ȌȀbǯDOWNLINK ȋͳǡʹǡ͵ȌȀcǯUPLINK ȋͳǡʹǡ͵ȌȀdǯDOWNLINK ȋͳǡʹǡ͵ȌȀNOTE: ConnectionsshouldnotcrossBands.Forexample,allBand1connectionsshouldbemadetothesamehybridpowercombiner/splitterconnectedtotherepeaterBTSthatmatchestheBand1frequency.5ǤȄǡǤ6ǤThewarrantydoesnotcoverdamagecausedwhenanungroundedHubispoweredon.NOTE: Usea50ohmterminatoronanyunusedpowercombiner/splitterports.3ConnectingMultipleFusionWidebandMainHubstoaDuplexRepeaterorBTSQuantity Item2 hybrid power combiner/splitters—one for uplink and one for downlink (2x1 for two Fusion Wideband Main Hubs, 3x1 for three, 4x1 for four, and so on)1 N-male to N-male coaxial jumper cables to connect each Fusion Wideband Main Hub’s RF Band to the power combiner/splitters2 circulator1 N-male to N-male coaxial jumper cable between each circulator and the repeater or base stationN-male to N-male coaxial jumper cable between each circulator and power combiner/splitter
Interfacing the Fusion Wideband Main Hub to an RF SourceInterReach Fusion Wideband Installation, Operation, and Reference Manual Page 155D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013 © 2013 TE Connectivity Ltd.ͶͷǤǡǤFigure45.Connecting Two Fusion Wideband Main Hub’s RF Band Ports to a Duplex Repeater or Base Station Band 1 Band 2 Band 3UL1 UL2 UL3AlarmsDL1 DL2 DL3AC PowerN-male to N-malecoaxial-jumper cablesbetween Combiner/Splitterand Fusion Main Hub’s Uplink Port for either Band 1,Band 2, or Band 32 x 1 PowerCombiner/Splitter2 x 1 PowerCombiner/SplitterN-male to N-malecoaxial-jumper cablesbetween Combiner/Splitter andFusion Main Hub’s Downlink Portfor either Band 1, Band 2, or Band 3Band 1 Band 2 Band 3UL1 UL2 UL3AlarmsDL1 DL2 DL3AC PowerCirculatorBase Stationto Repeater orN-male to N-malecoaxial-jumper cableN-male to N-malecoaxial-jumper cableN-male to N-malecoaxial-jumper cableInsert attenuator(if needed)
Installing Fusion Wideband Page 156 InterReach Fusion Wideband Installation, Operation, and Reference Manual© 2013 TE Connectivity Ltd D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013CONNECTINGCONTACTALARMSTOAFUSIONWIDEBANDSYSTEMȋȌǤ•AlarmSourceȄǡȋȌȋȌǤǦȋȌǤǡDzdzͳͷ͹ǤNOTE: ThecontactcanbechangedtonormallyͲopen(NO)withAdminBrowser.ThisisnotrecommendedsincenoalarmwouldbesentifpowertotheFusionWidebandMainHubfails.–Ǥ–ǦǦǤ•AlarmSenseȄ͵ǤǦȋȌǦȋȌǤǡǤǤǡDzdzͳ͸ͲǤͻͲǡǡȋȌǡǤȋȌǤTable90.AlarmTypesAlarm TypeFusion Wideband Connected toCable(s) Used Errors DetectedSource FlexWave 5-port Alarm Daisy-Chain Cable FaultsSource BTS 5-port Alarm Daisy-Chain Cable Faults and WarningsIn addition, a custom daisy-chain cable-to-BTS interface cable is required. Make this interface cable to the desired length and with the appropriate pin placement.Sense Unison 5-port Alarm Daisy-Chain Cable and the Alarm Sense Adapter CableFaults
Connecting Contact Alarms to a Fusion Wideband SystemInterReach Fusion Wideband Installation, Operation, and Reference Manual Page 157D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013 © 2013 TE Connectivity Ltd.AlarmSourceǡǤDzdzͳ͸ͲǤNOTE: Thefollowingproceduresassumethatthesystemisinstalledandthathasbeenprogrammedwithbands.UsingFlexWaveFocustoMonitorFusionWidebandǡȋȌȋȌǡͶ͸ǤȋȌǤFigure46.Connecting FlexWave to Fusion Wideband Band 1 Band 2 Band 3UL1 UL2 UL3AlarmsDL1 DL2 DL3AC PowerBand 1 Band 2 Band 3UL1 UL2 UL3AlarmsDL1 DL2 DL3AC PowerFusion Main HubMay need9-pin Adapterthat shipswith the cableAlarmSense5-port Alarm Daisy-Chain CableAlarmSourceAlarmSource
Installing Fusion Wideband Page 158 InterReach Fusion Wideband Installation, Operation, and Reference Manual© 2013 TE Connectivity Ltd D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013UsingaBaseStationtoMonitorFusionWidebandNOTE: TheBTSmustbeconfigured,bythecarrier,forcontactclosuremonitoringpriortoconnectingaFusionWidebandMainHubtoit.ǡȋȌȋȌǡͶ͹ǤǦǤǦǦǡǦǤDzȀdz͵͵ȋȌǤFigure47.Using a BTS to Monitor Fusion Wideband NOTE: Fornormallyopencontacts,thefaultandwarningcontactsneedtobewiredinparallelwithotherMainHubs.NOTE: TEdoesnotrecommendusingnormallyopencontacts.Band 1 Band 2 Band 3UL1 UL2 UL3AlarmsDL1 DL2 DL3AC PowerBand 1 Band 2 Band 3UL1 UL2 UL3AlarmsDL1 DL2 DL3AC PowerFusion Main HubAlarmSense5-port Alarm Daisy-Chain CableAlarmSourceBTSAlarmSource InterfaceCable(custom-made, on-site)
Connecting Contact Alarms to a Fusion Wideband SystemInterReach Fusion Wideband Installation, Operation, and Reference Manual Page 159D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013 © 2013 TE Connectivity Ltd.UsingaBaseStationandAdminBrowsertoMonitorFusionWidebandNOTE: TheBTSmustbeconfigured,bythecarrier,forcontactclosuremonitoringpriortoconnectingaFusionWidebandMainHubtoit.ǯƬǡͶͺǤDzdzͳ͹ʹǤFigure48.Using a BTS and AdminBrowserto Monitor Fusion WidebandBand 1 Band 2 Band 3UL1 UL2 UL3AlarmsDL1 DL2 DL3AC PowerFusion Main HubAlarmSense5-port Alarm Daisy-Chain CableAlarmSourceBTSPSTNInterfaceCable(custom-made, on-site)PC runningStandardBrowserSoftwareModemLine SwitchModemBand 1 Band 2 Band 3UL1 UL2 UL3AlarmsDL1 DL2 DL3AC PowerModemAlarmSource
Installing Fusion Wideband Page 160 InterReach Fusion Wideband Installation, Operation, and Reference Manual© 2013 TE Connectivity Ltd D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013AlarmSenseDzdzȋAdminBrowserUserManualȌǤNOTE: Thisprocedureassumesthatthesystemisinstalledandthathasbeenprogrammedwithbands.ǡȋȌȋȌǡͶͻǤȋȌǤFigure49.Using Fusion Wideband to Monitor UnisonǤǦǤǤFigure50.Alarm Sense Contacts5-port Alarm Daisy-Chain CableUp to 5 Unison Main HubsAlarmSourceAlarmSourceAlarmSenseFusion Main HubAlarm SenseAdapter Cable+5V81ExternalEquipmentContactsDiagnostic 1
Connecting Contact Alarms to a Fusion Wideband SystemInterReach Fusion Wideband Installation, Operation, and Reference Manual Page 161D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013 © 2013 TE Connectivity Ltd.AlarmCablesͷͳͷǦǦȋͶͲʹͶǦ͵ȌǡǤFigure51.5-port Alarm Daisy-Chain Cable1.2 meters (4 feet)J1FemaleJ2MaleJ3MaleJ4MaleJ5MaleJ6MaleJ7FemaleTerminatorNOTE: Do not daisy-chainFusion Main Hubswith FlexWave Focusif you want both faultsand warnings from Fusion.Only faults are reported ifyou combine Fusion withFlexWave in the same daisychain.7945DB-9 female toBase Station,FlexWave Focus,or the Alarm SenseAdapter Cable whenconnecting Unison7945SpliceSpliceDB-9 male to Fusion,Unison, FlexWave Focus,Alarm PortConnectorHoodDB-9 male to Fusion,Unison, FlexWave Focus,Alarm PortDB-9 male to Fusion,Unison, FlexWave Focus,Alarm PortDB-9 male to Fusion,Unison, FlexWave Focus,Alarm Port7945SpliceSplice7945SpliceSplice7945SpliceSplice794574Option 1: DB-9 to Fusion,Unison, FlexWave FocusAlarm Port. J7 not used.Option 2: Use J2-J5for Alarm ports. Use J6 toconnect to an additionalAlarm Daisy-Chain Cable.Do not use J7.Option 3: Connectfewer than 5 ports andconnect J7 to the lowestunused port to terminatethe daisy chain..5 meter(1.5 feet).5 meter(1.5 feet).5 meter(1.5 feet).5 meter(1.5 feet).25 meter(.75 feet)
Installing Fusion Wideband Page 162 InterReach Fusion Wideband Installation, Operation, and Reference Manual© 2013 TE Connectivity Ltd D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013ALARMMONITORINGCONNECTIVITYOPTIONSNOTE: Thefollowingproceduresassumethatthesystemisinstalledandthathasbeenprogrammedwithbands.DirectConnectionǡRJ-45 100 BASE-T ǯǦǤFigure52.OA&M Direct ConnectionModemConnectionǡǦǤFigure53.OA&M Modem Connection NOTE: Referto“CoaxialCable”onpage198forthemodemcablewiringinformation.PC runningStandardBrowserSoftwareCross-over100 BASE-T CableAdminBrowser isresident in Fusion.PSTNPC runningStandardBrowserSoftwareModem#140272-0Modem#140272-0#4028-10Straight-ThroughModem cable#4028-10Straight-ThroughModem cable
Alarm Monitoring Connectivity OptionsInterReach Fusion Wideband Installation, Operation, and Reference Manual Page 163D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013 © 2013 TE Connectivity Ltd.ǣ•Ǧǣͳǡʹ͸•Ǧǣʹ͸ǤSettingUpFusionWidebandModem(USRModem)UsingAdminBrowserǦǣ1Ǥ2SystemConfigurationǤ3SelectSetupModemConnectionǤǣ4ǣǤ••5SetupConnectionǤTE
Installing Fusion Wideband Page 164 InterReach Fusion Wideband Installation, Operation, and Reference Manual© 2013 TE Connectivity Ltd D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013SettingUpaPCModemUsingWindowsǦǤ1StartǡSettingsǡNetworkConnectionsǤǤ2ClickCreateanewconnectionǤǤ
Alarm Monitoring Connectivity OptionsInterReach Fusion Wideband Installation, Operation, and Reference Manual Page 165D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013 © 2013 TE Connectivity Ltd.3NextǤǤ4ConnecttothenetworkatmyworkplaceNextǢǤ5DialǦupconnectionNextǢǤ
Installing Fusion Wideband Page 166 InterReach Fusion Wideband Installation, Operation, and Reference Manual© 2013 TE Connectivity Ltd D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 20136NextǢǤ7PhonenumberNextǢǤ8Anyone’suseNextǢǤ
Alarm Monitoring Connectivity OptionsInterReach Fusion Wideband Installation, Operation, and Reference Manual Page 167D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013 © 2013 TE Connectivity Ltd.9FinishǢǤ10 PropertiesǢǤǣ•ǣppp_user•ȋǡȌǣpassword
Installing Fusion Wideband Page 168 InterReach Fusion Wideband Installation, Operation, and Reference Manual© 2013 TE Connectivity Ltd D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 201311 Configure...Ǥ12 OKǤ13 SecurityǢǤ14 TypicalNetworkingǢǤ
Alarm Monitoring Connectivity OptionsInterReach Fusion Wideband Installation, Operation, and Reference Manual Page 169D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013 © 2013 TE Connectivity Ltd.15 InternetProtocol(TCP/IP)PropertiesǢǤ16 ObtainanIPaddressautomaticallyObtainDNSserveraddressautomaticallyǡOKǤ17 ǦǡǡDzȋȌdzͳ͸͵Ǥ100BASEͲTPortExpanderConnectionͳͲͲǦǤͶǦǤǤFigure54.OA&M Connection using a 232 Port ExpanderPC runningStandardBrowserSoftwareLAN Switch100 BASE-TEthernet connectionAdminBrowser isresident in Fusion.100 BASE-T CableRJ-45 Male to RJ-45 Male
Installing Fusion Wideband Page 170 InterReach Fusion Wideband Installation, Operation, and Reference Manual© 2013 TE Connectivity Ltd D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013POTSLineSharingSwitchConnectionǡǤFigure55.OA&M Connection Using a POTS Line Sharing SwitchModem#4028-10 Straight-ThroughModem cablePC runningStandardBrowserSoftwarePSTNModem#140272-0#4028-10Straight-ThroughModem cableLine Sharing Switch4- or 8-port4-port: #240031-08-port: #240052-0StandardphonecableUp to 4 modemsper switchModem#140272-0
Alarm Monitoring Connectivity OptionsInterReach Fusion Wideband Installation, Operation, and Reference Manual Page 171D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013 © 2013 TE Connectivity Ltd.Figure56.Cascading Line Sharing SwitchesEthernetRFModemǦǤǡǤ#4028-10Straight-ThroughModem cablePC runningStandardBrowserSoftwarePSTNModem#140272-0#4028-10Straight-ThroughModem cable4- or 8-PortLine Sharing Switch4- or 8-portLine Sharing Switch PNs:4-port: #240031-08-port: #240052-0Standard phone cable4- or 8-PortLine Sharing Switch4- or 8-PortLine Sharing Switch4- or 8-PortLine Sharing Switch4- or 8-PortLine Sharing SwitchModemModemModemModemModemModemModemModemModemModemModemModemModemModemModemModem
Installing Fusion Wideband Page 172 InterReach Fusion Wideband Installation, Operation, and Reference Manual© 2013 TE Connectivity Ltd D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013EthernetLANConnectionǤͶǦǤFigure57.OA&M Connection Using Ethernet and ENET/232 Serial HubSNMPInterfaceȋȌȋȌǤǤȋȌͳʹǤPC runningStandardBrowserSoftwareTCP/IP LAN SwitchEthernet Ethernet100 BASE-T CableMale RJ-45 to Male RJ-45
Alarm Monitoring Connectivity OptionsInterReach Fusion Wideband Installation, Operation, and Reference Manual Page 173D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013 © 2013 TE Connectivity Ltd.Figure58.Fusion Wideband SNMP Configuration OptionsRemote Unit Remote UnitExpansion HubExpansion HubMain HubRS-232Modem PortPPP Modem PSTNPPP ModemRemote Unit Remote UnitExpansion HubMain HubPSTN(b) Connection to multiple systems through Dial-in routerRemote Unit Remote Unit(c) DSL Modem through internet(d) Connection to corporate LAN through firewallLANEthernetPort EthernetPortDialup Router/Firewall ModemPPP PPPRouterMain Hub EthernetPortEthernetPortRouterSwitchDSL Modem DSL ModemRouterPSTN/InternetEthernetPortEthernet PortMain HubLANFirewallRouter RouterInternet
Installing Fusion Wideband Page 174 InterReach Fusion Wideband Installation, Operation, and Reference Manual© 2013 TE Connectivity Ltd D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
InterReach Fusion Wideband Installation, Operation, and Reference Manual Page 175D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013 ©2013 TE Connectivity Ltd.REPLACINGFUSIONWIDEBANDCOMPONENTSReplacinganRAU................................................................................................................................................................. 176ReplacetheRAU .....................................................................................................................................................................176PerformSystemTest ..............................................................................................................................................................176ChecktheRAULEDs ...............................................................................................................................................................177ReplacingaFusionWidebandExpansionHub ...................................................................................................................... 178ReplaceaFusionWidebandExpansionHub...........................................................................................................................178AdminBrowserTasks ..............................................................................................................................................................178ChecktheExpansionHubLEDs...............................................................................................................................................178ReplacingaFusionWidebandMainHub .............................................................................................................................. 179ReplaceaFusionWidebandMainHub...................................................................................................................................179ConfiguretheNewFusionWidebandMainHub....................................................................................................................179ChecktheLEDsontheNewMainHub ...................................................................................................................................180Topics Page
Replacing Fusion Wideband Components Page 176 InterReach Fusion Wideband Installation, Operation, and Reference Manual© 2013 TE Connectivity Ltd D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013REPLACINGANRAUCAUTION! ThenewRAUmustsupportthesamebandsastheoneyouarereplacing.IftheRAUisofthewrongbandcombination,itwillnotoperateproperlyinthesystem.1ǡSYSTEM INFORMATIONǤ2SHOW SYSTEM TREEǡǡGET SYSTEM INFORMATION.ǤǤ3CANCELǤ4Ǥ5Ǥ6Ǥ7Ǥ8SYSTEM CONFIGURATION.9SHOW SYSTEM TREEǤ10 EDIT UNIT PROPERTIESǤ11 SAVE PROPERTIESǤǡǤCAUTION! DuringSystemTest,theentiresystemistemporarilyoffͲlineandnoRFisbeingtransmitted.3ReplacetheRAU3PerformSystemTest
Replacing an RAUInterReach Fusion Wideband Installation, Operation, and Reference Manual Page 177D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013 © 2013 TE Connectivity Ltd.1ǯLINKALARMȋȀȌǤǡǤ2ǡǡǡǤaLINKALARMǡǤǢǤbǯǡǤcȋͻͲȌǡǤ3ChecktheRAULEDs
Replacing Fusion Wideband Components Page 178 InterReach Fusion Wideband Installation, Operation, and Reference Manual© 2013 TE Connectivity Ltd D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013REPLACINGAFUSIONWIDEBANDEXPANSIONHUB1Ǥ2ǡǡǤ3Ǥ4ǡǡȂǤ5Ǥ•Ǥ•ǡǤCAUTION! DuringSystemTest,theentiresystemistemporarilyoffͲlineandnoRFisbeingtransmitted.Forafullyloadedsystem(oneMainHub,fourExpansionHubs,and32RAUs),itcantakeupto90secondstocompletethetest.•Ǥ–ǡǤ–ǡǤ•UL STATUSDL STATUSǤ•E-HUB STATUS POWERǤ•ǤǤNOTE: RefertoDzdzͳͺ͸fortroubleshootingusingtheLEDs.3ReplaceaFusionWidebandExpansionHub3AdminBrowserTasks3ChecktheExpansionHubLEDs
Replacing a Fusion Wideband Main HubInterReach Fusion Wideband Installation, Operation, and Reference Manual Page 179D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013 © 2013 TE Connectivity Ltd.REPLACINGAFUSIONWIDEBANDMAINHUBǯǤǤǡǤǡǦǤ1ǡǡSYSTEM INFORMATIONǡSHOW SYSTEM TREEǡǡGET SYSTEM INFORMATIONǤ2Ǥ3Ǥ4Ǥ5Ǥ6ǯͳͲͲǦǤȀȌ7Ǥ8Ǥ9ǤǤǤͳʹǤCAUTION! DuringSystemTest,theentiresystemistemporarilyoffͲlineandnoRFisbeingtransmitted.1Ǥ2SYSTEM CONFIGURATIONǤ3SET DATE/TIMEǤ4SET DATE/TIMEǤ5Ǥ6ǡSYSTEM CONFIGURATIONǤ7INSTALL SYSTEMǤ8INSTALL SYSTEM ȋǡǡǡȌǤ9Ǥ10 SYSTEM CONFIGURATIONSETUP NETWORK CONNECTION OR MODEM CONNECTIONǤ3ReplaceaFusionWidebandMainHub3ConfiguretheNewFusionWidebandMainHub
Replacing Fusion Wideband Components Page 180 InterReach Fusion Wideband Installation, Operation, and Reference Manual© 2013 TE Connectivity Ltd D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013•ͷǦǤ–ǡǤ–ǡǤ•ǡǡPORTǤ•Dzdzͳͺ͸ǤNOTE: IfthereisnocommunicationbetweentheMainHubandtheExpansionHubs,usetheAdminBrowsertoisolatesystemproblems.3ChecktheLEDsontheNewMainHub
InterReach Fusion Wideband Installation, Operation, and Reference Manual Page 181D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013 ©2013 TE Connectivity Ltd.MAINTENANCE,TROUBLESHOOTING,ANDTECHNICALASSISTANCEService................................................................................................................................................................................. 182Maintenance ....................................................................................................................................................................... 183CleaningtheFiberPorts .........................................................................................................................................................183Considerations................................................................................................................................................................183UsingCompressedAir.....................................................................................................................................................183UsingIsopropylAlcohol ..................................................................................................................................................183Troubleshooting .................................................................................................................................................................. 184TroubleshootingUsingAdminBrowser...................................................................................................................................185SystemTroubleshooting.................................................................................................................................................185TroubleshootingRecommendations ..............................................................................................................................185Fault/Warning/StatusIndications ..................................................................................................................................186TroubleshootingUsingLEDs ...................................................................................................................................................186TroubleshootingMainHubLEDsDuringNormalOperation ..........................................................................................186TroubleshootingExpansionHubLEDsDuringNormalOperation ..................................................................................188TroubleshootingCATV ......................................................................................................................................................... 189TechnicalAssistance ............................................................................................................................................................ 190Topics Page
Maintenance, Troubleshooting, and Technical Assistance Page 182 InterReach Fusion Wideband Installation, Operation, and Reference Manual© 2013 TE Connectivity Ltd D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013SERVICEǦǤǤǤAddress 541 E. Trimble RoadSan Jose, California95131-1224 USAHelp Hot LineU.S. and Canada 1-800-530-9960All Others +1-952-917-0761Help Web URL http://www.te.com/WirelessSupport
MaintenanceInterReach Fusion Wideband Installation, Operation, and Reference Manual Page 183D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013 © 2013 TE Connectivity Ltd.MAINTENANCEǤǤCleaningtheFiberPortsǯǤConsiderations•ǣ–ǡǡǤ–Ǥ•Ǧǣ–ͻͺΨǤUsingCompressedAir1ǯǤ2ǤUsingIsopropylAlcohol1ǯǤ2ʹǤͷǦǡǦǤ3Ǥ4ǤǡǤ
Maintenance, Troubleshooting, and Technical Assistance Page 184 InterReach Fusion Wideband Installation, Operation, and Reference Manual© 2013 TE Connectivity Ltd D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013TROUBLESHOOTINGNOTE: FusionhasnouserͲserviceableparts.FaultyorfailedunitsarefullyreplaceablethroughTE;see“Service”onpage182.ǣ•Ȁ••ǡǡ••••NOTE: Faultycablingisthecauseofavastmajorityofproblems.AllCATV75OhmcableshouldbetestedtoTIAͲ570ͲBspecifications.TheRAUwillbedamagedifthecableconnectorisnotinstalledproperly.ǡǤǡǤǡ“Service”onpage182.ǣ•••ͳǤͲͲǡǤǤ•ǫȋǦ͸Ȍǫ••ǫ
TroubleshootingInterReach Fusion Wideband Installation, Operation, and Reference Manual Page 185D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013 © 2013 TE Connectivity Ltd.TroubleshootingUsingAdminBrowserǤǡǯǡǡǤNOTE: AdminBrowserv1.00displaysevents(faults,warnings,orstatusmessages)dependingonyourviewpreference.Tochangeyourviewpreference,referto“ViewPreference”onpage38.SystemTroubleshootingǡSYSTEM INFORMATIONǡGET FAULTS, WARNINGS AND STATUSESǤǡǤǢǢǡǤNOTE: Systemcommandscantakelongertoexecutecomparedtocomponentcommands.NOTE: ThisRAUicon  indicatesthereisfaultontheRAU.Thisicon  indicatesadisconnecteddevice.Youcannotrequeststatusonadisconnecteddevice.TroubleshootingRecommendationsǡǡǣ•Ǥ–Ǥ–ǢDzdzͳͺ͵Ǥ–Ǥ•ǡ CLEAR ALL DISCONNECTSǤ•Ǥ•ǤǤ•ǣ–Ǥ–ǡǤ–ǤǡSHOW SYSTEM TREEǤSET OUT OF SERVICE/SET IN SERVICEǤ
Maintenance, Troubleshooting, and Technical Assistance Page 186 InterReach Fusion Wideband Installation, Operation, and Reference Manual© 2013 TE Connectivity Ltd D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013Fault/Warning/StatusIndicationsǡǤǤǤǡǤǡDzdzDzdzǤǢǤNOTE: IfyouhavearedSTATUSLEDwithoutafaultmessage,itprobablyindicatesthattheunitislockedout.ǡǡǤTroubleshootingUsingLEDsǡǡǢǤǡǡǤǤǤTroubleshootingMainHubLEDsDuringNormalOperationǯǤǡǤ
TroubleshootingInterReach Fusion Wideband Installation, Operation, and Reference Manual Page 187D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013 © 2013 TE Connectivity Ltd.Table91.TroubleshootingMainHubPortLEDsDuringNormalOperationDuringNormal OperationMain Hub Port LEDsState Action ImpactExpansion Hub Not ConnectedPORT Red If the Expansion Hub was disconnected accidentally, re-connect the cables. The LEDs should change to Green/Red (then Green/Green, after 20 seconds, if the Main Hub band has been programmed).When the Expansion Hub is to be removed from service permanently, use AdminBrowser’s ‘Clear All Disconnect Status’ command to clear all disconnect states to no connect states. The Expansion Hub was previously connected, but it is not currently connected; the Expansion Hub uplink cable disconnected.AdminBrowser clears all disconnects caused by installation as part of the clean-up process. After installation, power cycle the Main Hub or use AdminBrowser’s “Clear All Disconnect Status” command.Changes the Main Hub’s port LEDs to Off/Off.Expansion Hub ConnectedPORT Flashing Red (60 ppm)Use AdminBrowser to determine the exact cause of the Main Hub’s faults.Lost communication with Expansion Hub; could be Expansion Hub problem or fiber cable problem.The Expansion Hub communication problems delay MH responses to AdminBrowser commands, resulting in command time-outs. You can disconnect the offending Expansion Hub initially to obtain status from the rest of the system, then connect the Expansion Hub and resolve the communication problem.PORT Red The Expansion Hub or connected RAU reports a fault condition; use AdminBrowser to determine the exact cause of the Expansion Hub and RAU’s faults.Degraded performance or unit may be off-line.Depends on fault condition.Table92.TroubleshootingMainHubStatusLEDsDuringNormalOperationDuringNormal OperationMain Hub Status LEDsState Action ImpactAt Any Time main hub statusRed Use AdminBrowser to determine the exact cause of the fault.Power cycle one time. If the fault remains, replace the Main Hub.Internal Main Hub fault.Use AdminBrowser to check if the Main Hub is commanded Out-of-Service (every Expansion Hub port status LED will be red as well). A power cycle will not clear a commanded Out-of-Service, you must use AdminBrowser to clear this state.The Main Hub and all downstream units are off-line.main hub statusFlashing Red (60ppm)Reduce input signal power. Signal compression.At Any Time Power Red Replace the Main Hub. One or more power supplies are out of specification.
Maintenance, Troubleshooting, and Technical Assistance Page 188 InterReach Fusion Wideband Installation, Operation, and Reference Manual© 2013 TE Connectivity Ltd D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013TroubleshootingExpansionHubLEDsDuringNormalOperation•LINKE-HUB/RAUȀǡǡǡǤ•POWERǡ EHUB STATUSǡDL STATUSǡ UL STATUS ǤTable93.TroubleshootingExpansionHubPortLEDsDuringNormalOperationDuringNormal OperationExpansion Hub Port LEDsState Action ImpactRAU is not connectedPORT Off If the RAU was disconnected accidentally, re-connect the CATV cable. The Expansion Hub’s port LEDs should change to Green/Red (then Green/Green, after 20 seconds, if the Main Hub is connected, powered on, and has band programmed).Use AdminBrowser’s “Clear All Disconnect Status” command if you are permanently removing the RAU from service. The Expansion Hub’s port LEDs should change to Off/Off.The RAU was previously connected, but it is not currently connected; the RAU cable is disconnected.RAU is connectedPORT Red Disconnect/reconnect the CATV cable to force power-on reset to the RAU. If the port LEDs remain Red check for the exact cause of Expansion Hub faults using AdminBrowser.Lost communications with the RAU. The RAU could have powered down due to over current; cable could have been damaged.PORT Flashing Red (60 ppm)The RAU reports a fault condition; check for the exact cause of Expansion Hub and RAU faults using AdminBrowser.Depends on the fault condition.PORT Flashing Red (60 ppm)The Expansion Hub reports no connection, cable shorts, or a current port trap condition.Expansion Hub communications with the RAU. The Expansion Hub is at fault. The cable could have been damaged. The cable leads may be shorted.Table94.TroubleshootingExpansionHubStatusLEDsDuringNormalOperationDuringNormal OperationExpansion Hub Status LEDsState Action ImpactAt Any Time ul status Red Check uplink fiber for optical loss.Power cycle Expansion Hub one time to check uplink laser.No communications between the Main Hub and the Expansion Hub.Uplink laser failure.dl status Red Check the downlink fiber for optical lossNo communications with the Main Hub.E-h statusRed If either the UL STATUS or the DLSTATUS are also red, see above.Cycle power on the Expansion Hub. If fault remains, replace the Expansion Hub.Internal Expansion Hub fault (including either of the above UL STATUS or DLSTATUS states).
Troubleshooting CATVInterReach Fusion Wideband Installation, Operation, and Reference Manual Page 189D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013 © 2013 TE Connectivity Ltd.TROUBLESHOOTINGCATVǡǤNOTE: RecommendedminimumandmaximumCATVcablelengthsvarydependinguponthetypeofCATVcableused.Referto“CableandConnectorRequirements”onpage107.Table95.SummaryofCATVCableWiringProblemsProblem Type Message Icon ImpactLoose connector, shorted conductor or improper connection to the shield.None High phase noise, degraded signal on both Downlink and Uplink (high bit error rate)No communication with RAUn RAU unable to communicate with Hub, degraded performance or RAU off-linePortn UL RF path loss is too high Increased ripple in the uplink path, decreased UL gain, or no UL gainThe DL RF path loss is too high Increased ripple in the downlink path, RAU off-lineRAUn over current or port short RAU will not power on.
Maintenance, Troubleshooting, and Technical Assistance Page 190 InterReach Fusion Wideband Installation, Operation, and Reference Manual© 2013 TE Connectivity Ltd D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013TECHNICALASSISTANCEǢDzdzͳͺʹǤǡǡǦǡǤǤ•••ǡǡ•ȋȌǡ•••ǡǡ
InterReach Fusion Wideband Installation, Operation, and Reference Manual Page 191D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013 ©2013 TE Connectivity Ltd.APPENDIXA:CABLESANDCONNECTORS75OhmCATVCable ............................................................................................................................................................. 192GeneralSpecifications ............................................................................................................................................................192RecommendedCATVCableLengths.......................................................................................................................................192ConnectorsandToolsforCableEnds .....................................................................................................................................196FiberOpticalCables ............................................................................................................................................................. 197CoaxialCable ....................................................................................................................................................................... 198StandardModemCable ....................................................................................................................................................... 199TCP/IPCrossͲOverCable ...................................................................................................................................................... 200DBͲ9toDBͲ9NullModemCable .......................................................................................................................................... 201Topics Page
Appendix A: Cables and Connectors Page 192 InterReach Fusion Wideband Installation, Operation, and Reference Manual© 2013 TE Connectivity Ltd D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 201375OHMCATVCABLEGeneralSpecifications•ȋȌ•ȋȌȋȌ•ǤǯͷͶǤ••͹ͷǦ•–ǦͷͻǣȈǣͲȋͲǤȌȈǣͳͷͲȋͶͻʹǤȌ–Ǧ͸ǣȈǣͲȋͲǤȌȈǣͳ͹ͲȋͷͷͺǤȌ–ǦͳͳǣȈǣͲȋͲǤȌȈǣʹ͹ͷȋͻͲʹǤȌRecommendedCATVCableLengthsǤȋǤȌ•ǣ•ʹͲ͸ͷͷǦͷͻǤǦͳǤ•ʹʹ͹ͻǦ͸ǤǦʹǤ•ʹʹͻ͵ǦͳͳǤǦ͵Ǥ•ʹͲ͸ͷǦͷͻ•ʹʹ͹ͻǦ͸•ʹʹͻ͵Ǧͳͳ
75 Ohm CATV CableInterReach Fusion Wideband Installation, Operation, and Reference Manual Page 193D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013 © 2013 TE Connectivity Ltd.Figure59.CommScope 2065V for RG-59
Appendix A: Cables and Connectors Page 194 InterReach Fusion Wideband Installation, Operation, and Reference Manual© 2013 TE Connectivity Ltd D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013Figure60.CommScope 2079V for RG-6
75 Ohm CATV CableInterReach Fusion Wideband Installation, Operation, and Reference Manual Page 195D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013 © 2013 TE Connectivity Ltd.Figure61.CommScope 2293K for RG-11NOTE: TErequiressolidcoppercenterconductorCATVcableforproperDCvoltagetotheRAUandmaximumdistances.
Appendix A: Cables and Connectors Page 196 InterReach Fusion Wideband Installation, Operation, and Reference Manual© 2013 TE Connectivity Ltd D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013ConnectorsandToolsforCableEndsǣ•ǣʹͲ͸ͷ•ǣǦͶ•ǦͳǡǦͶǡͳͲͲ•ǣʹʹ͹ͻ•ǣǦͷͷ•ǦͳǡǦ͵ͷǡͳͲͲ•ǣʹʹͻ͵•ǣǦ͹ͳ•ǦͳǡǦ͹ǡͳͲͲǡǦǦǤͻ͸ǡǦǡǡǦǦǤTable96.SystemGain(Loss)RelativetoCATVCableLengthCable TypeCommScope Part NumberPlenum RatedSolid Copper ConductorCopper Clad ConductorZero-loss RF Maximum Length (meters)Distance Where RF is 10dB Below Input RF (meters)RG-59 2065V Yes X 130 1802022V Yes X 100 100*5572R No X 95 95*5565 No X 130 180RG-6 2279V Yes X 140 1902275V Yes X 140 150*5726 No X 140 140*5765 No X 140 190RG-11 2293K Yes X 235 3202285K Yes X 235 300*5913 No X 235 300** Exceeding the distance of copper-clad cable will result in the attached RAU becoming non-functional. If the distance of a cable run is at its maximum and is of concern, TE recommends the use of solid copper cable to ensure successful operation.
Fiber Optical CablesInterReach Fusion Wideband Installation, Operation, and Reference Manual Page 197D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013 © 2013 TE Connectivity Ltd.FIBEROPTICALCABLES•ȋȌ•ȋȌȋȌ••Ǧ͸ʹǤͷρȀͳʹͷρǦʹͺǡǤ•ȀȋǦȌȋǦǦȌǡ•ǣ–ǦǣͷͲͲȋͳǡ͸ͶͲȌȂ͵–Ǧǣ͸ȋͳͻǡ͸ͺͷȌȂ͵
Appendix A: Cables and Connectors Page 198 InterReach Fusion Wideband Installation, Operation, and Reference Manual© 2013 TE Connectivity Ltd D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013COAXIALCABLE•ȋǦȌ•ȋǦȌ
Standard Modem CableInterReach Fusion Wideband Installation, Operation, and Reference Manual Page 199D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013 © 2013 TE Connectivity Ltd.STANDARDMODEMCABLEȋͶͲʹͺǦͳͲȌǯǤFigure62.Standard Modem Cable PinoutsDB-9 ConnectorPinDB-25 ConnectorPin12345678983220764522
Appendix A: Cables and Connectors Page 200 InterReach Fusion Wideband Installation, Operation, and Reference Manual© 2013 TE Connectivity Ltd D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013TCP/IPCROSSͲOVERCABLEȀǦȋͶͲ͸ͻǦȌǤǤ͸͵ǤFigure63.Wiring Map for TCP/IP Cable
DB-9 to DB-9 Null Modem CableInterReach Fusion Wideband Installation, Operation, and Reference Manual Page 201D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013 © 2013 TE Connectivity Ltd.DBͲ9TODBͲ9NULLMODEMCABLEǦͻǦͻǯȀǦʹ͵ʹǤͻ͹͸ͶǤFigure64.DB-9 Female to DB-9 Female Null Modem Cable DiagramTable97.DBͲ9FemaletoDBͲ9FemaleNullModemCablePinoutFrom Signal To SignalP1-4 DTR P2-6, P2-1 DSR, DCD P1-6 DSR P1-1, P2-4 DCD, DTR P1-3 TXD P2-2 RXD P1-2 RXD P2-3 TXD P1-5 GND P2-5 GND P1-7 RTS P2-8 CTS P1-8 CTS P2-7 RTSP1-9 N/C N/C N/CDB-9 ConnectorPinDB-9 ConnectorPin123456789123456789Note that for each DB-9 connector, pins 1 and 6 are tiedtogether and sent to pin 4 of the opposite connector,providing the required handshake signals.
Appendix A: Cables and Connectors Page 202 InterReach Fusion Wideband Installation, Operation, and Reference Manual© 2013 TE Connectivity Ltd D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
InterReach Fusion Wideband Installation, Operation, and Reference Manual Page 203D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013 ©2013 TE Connectivity Ltd.APPENDIXB:COMPLIANCEFusionWidebandSystemApprovalStatus ........................................................................................................................... 204700MHzLTEProducts............................................................................................................................................................204800SMR/iDENProducts .........................................................................................................................................................204850CellularProducts..............................................................................................................................................................2041800DCSProducts .................................................................................................................................................................2041900PCSProducts..................................................................................................................................................................2042100UMTSProducts ..............................................................................................................................................................2051700/2100AWSProducts ......................................................................................................................................................2052500WiMAXProducts............................................................................................................................................................2052600MHzLTEProducts..........................................................................................................................................................205InterReachFusionWidebandMainHubandExpansionHub.................................................................................................206HumanExposuretoRF......................................................................................................................................................... 207Topics Page
Appendix B: Compliance Page 204 InterReach Fusion Wideband Installation, Operation, and Reference Manual© 2013 TE Connectivity Ltd D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013FUSIONWIDEBANDSYSTEMAPPROVALSTATUSǤ700MHzLTEProducts•ǣǡǡ͸ͲͻͷͲǡ͵ǡ͸ͲͻͷͲǦͳǡͳǡǤ•ǣͳͷ•ǣʹ͹800SMR/iDENProducts•ǣǡǡ͸ͲͻͷͲǡ͵ǡ͸ͲͻͷͲǦͳǡͳǡǤ•ǣͳͷ•ǣͻͲ850CellularProducts•ǣǡǡ͸ͲͻͷͲǡ͵ǡ͸ͲͻͷͲǦͳǡͳǡǤ•ǣͳͷ•ǣʹʹ1800DCSProducts•ǣǡǡ͸ͲͻͷͲǡ͵ǡ͸ͲͻͷͲǦͳǡͳǡǤ•ǣ͵ͲͳͶͺͻǦͺͳǤʹǤͳ•ǣ͵ͲͲ͸ͲͻǦͶͻǤʹǤͳ1900PCSProducts•ǣǡǡ͸ͲͻͷͲǡ͵ǡ͸ͲͻͷͲǦͳǡͳǡǤ•ǣͳͷ•ǣʹͶ
Fusion Wideband System Approval StatusInterReach Fusion Wideband Installation, Operation, and Reference Manual Page 205D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013 © 2013 TE Connectivity Ltd.2100UMTSProducts•ǣǡǡ͸ͲͻͷͲǡ͵ǡ͸ͲͻͷͲǦͳǡͳǡǤ•ǣ͵ͲͳͶͺͻǦʹ͵ͳǤʹǤͳ•ǣ͵ͲͳͻͲͺǦͳͳʹǤ͵Ǥͳ1700/2100AWSProducts•ǣǡǡ͸ͲͻͷͲǡ͵ǡ͸ͲͻͷͲǦͳǡͳǡǤ•ǣͳͷ•ǣʹ͹2500WiMAXProducts•ǣǡǡ͸ͲͻͷͲǡ͵ǡ͸ͲͻͷͲǦͳǡͳǡǤ•ǣͳͷ•ǣʹ͹2600MHzLTEProducts•ǣǡǡ͸ͲͻͷͲǡ͵ǡ͸ͲͻͷͲǦͳǡͳǡǤ•ǣ͵ͲͳͶͺͻǦʹ͵ͳǤʹǤͳ•ǣ͵ͲͳͻͲͺǦͳͳʹǤ͵Ǥͳ
Appendix B: Compliance Page 206 InterReach Fusion Wideband Installation, Operation, and Reference Manual© 2013 TE Connectivity Ltd D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013InterReachFusionWidebandMainHubandExpansionHub•ǣǡǡ͸ͲͻͷͲǦͳǡǡǤ•ǣʹʹ•ǣʹͶNOTE: ForCanadiancustomers,theManufacturer’sratedoutputpower1ofthisequipmentisforsinglecarrieroperation.Forsituationswhenmultiplecarriersignalsarepresent,theratingwouldhavetobereducedby3.5dB,especiallywheretheoutputsignalisreͲradiatedandcancauseinterferencetoadjacentbandusers.Thispowerreductionistobebymeansofinputpowerorgainreductionandnotbyanattenuatorattheoutputofthedevice.NOTE: ThisdevicecomplieswithPart15oftheFCCRules.Operationissubjecttothefollowingtwoconditions:(1)thisdevicemaynotcauseharmfulinterference,and(2)thisdevicemustacceptanyinterferencereceived,includinginterferencethatmaycauseundesiredoperation.NOTE: ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassAdigitaldevice,pursuanttoPart15oftheFCCRules.Theselimitsaredesignedtoprovidereasonableprotectionagainstharmfulinterferencewhentheequipmentisoperatedinacommercialenvironment.Thisequipmentgenerates,uses,andcanradiateradiofrequencyenergyand,ifnotinstalledandusedinaccordancewiththeinstructionmanual,maycauseharmfulinterferencetoradiocommunications.ȀǤǯǤ1 “Manufacturer’s rated output power” refers to Fusion Wideband’s downlink P1dB. The power per carrier tables take into account this power reduction for multiple carriers.WARNING.NOTCONSUMERǤFCCLICENSEESQUALIFIEDINSTALLERSǤMUSTFCCLicenseǤǡ̈́ͳͲͲǡͲͲͲǤPart 90 Signal BoostersWARNING.NOTCONSUMERǤFCCLICENSEESQUALIFIEDINSTALLERSǤMUSTFCCLicenseǤȋͶ͹ͻͲǤʹͳͻȌwww.fcc.gov/signalǦboosters/registrationǤǡ̈́ͳͲͲǡͲͲͲǤ
Human Exposure to RFInterReach Fusion Wideband Installation, Operation, and Reference Manual Page 207D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013 © 2013 TE Connectivity Ltd.HUMANEXPOSURETORFǤǤȋȌǤȋȌ͵ͲͲͳͲͲǤǡǡǤǢʹͲȋ͹͹ȀͺdzȌǤʹͲǡǤͳǤͷȋʹǤͶͻȌǤͳǤͷǡǤʹͲʹǡʹǤͳͲͻͳǤǡǡǡ͸ͷDzEvaluationCompliancewithFCCGuidelinesforHumanExposuretoRadioFrequencyforElectricFieldsdzǤǤʹͲǣ•͵ͲͲͳǤͷȀͳͷͲͲ•ͳǤͷͳȀʹǣS = PG / 4SR2SȀʹPGǡȋȌǡǡǤRǤǣͳͲǡ͸ǡͶȋͳͳʹǤȌǤͳͻͲͲǡǡ͸Ǥ͵͸ǦͶǡͳ͸ǤͷǤ͹ǡʹ͵ǤͷȋʹʹͶȌǤαȀͶSʹαʹʹͶȀȋͶ͵ǤͳͶȌȋͳʹʹȌʹαͲǤͲͲͳȀʹǡʹͲǣαʹʹͶȀȋͶ͵ǤͳͶȌȋʹͲȌʹαͲǤͲͶȀʹ
Appendix B: Compliance Page 208 InterReach Fusion Wideband Installation, Operation, and Reference Manual© 2013 TE Connectivity Ltd D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
InterReach Fusion Wideband Installation, Operation, and Reference Manual Page 209D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013 ©2013 TE Connectivity Ltd.APPENDIXC:FAULTS,WARNINGS,STATUSTABLESFORFUSION,FUSIONWIDEBAND,FUSIONSINGLESTARFaultsReportedbyMainHubs ............................................................................................................................................. 210FaultsReportedforSystemCPU........................................................................................................................................... 213FaultsforExpansionHubs.................................................................................................................................................... 214FaultsforRAUs .................................................................................................................................................................... 216MessagesforMainHubs...................................................................................................................................................... 217WarningMessages .................................................................................................................................................................217StatusMessages .....................................................................................................................................................................217MessagesforSystemCPUs................................................................................................................................................... 222MessagesforExpansionHubs .............................................................................................................................................. 223MessagesforRAUs .............................................................................................................................................................. 226ǡǤTopics Page
Appendix C: Faults, Warnings, Status Tables for Fusion, Fusion Wideband, Fusion SingleStar Page 210 InterReach Fusion Wideband Installation, Operation, and Reference Manual© 2013 TE Connectivity Ltd D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013FAULTSREPORTEDBYMAINHUBSǦǤǡǤǤǤǡǤǡDzdzDzdzǤǢǤNOTE: IfyouhavearedSTATUSLEDwithoutafaultmessage,itprobablyindicatesthattheunitislockedout.Table98.FaultMessagesforMainHubsMessage NumberDescription Reason/Action{MF01} Software error occurred and recovered. If this happens repeatedly, replace the Hub.{MF02} Software error occurred and recovered. If this happens repeatedly, replace the Hub.{MF03} Software error occurred and recovered. If this happens repeatedly, replace the Hub.{MF04} Software reset occurred and recovered, or firmware download.If this happens repeatedly, replace the Hub.{MF05} Software error occurred and recovered. If this happens repeatedly, replace the Hub.{MF06} Problem detected in the Hub. Internal communication reset.Contact TE Support for more information.{MF07} Hub power cycle. Hub power cycle.{MF08} Internal communications failure. No internal communications in preceding 15 minutes.{MF09} Hardware Reset. Commanded hardware power on reset{MF10} Band not programmed. Use AdminBrowser to program the band.{MF11} Hardware failure (DL Pilot PLL). Cycle power once. If fault persists, replace the Hub{MF12} Hardware failure (DL Pilot Too High). Cycle power once. If fault persists, replace the Hub.{MF13} Hardware failure (DL Pilot Too Low). Cycle power once. If fault persists, replace the Hub.{MF14} Hardware failure (54 VDC). 54 VDC power supply is out of range, replace the Hub{MF15} Hardware failure (RF VDC Power). Loss of DC power to RF circuits, replace the Hub.{MF16} Self Lockout (All Bands). Hub has shutdown the system due to an internal fault. System is offline.{MF17} Hardware failure (DL PLL Band 1). Cycle power once. If fault persists, replace the Hub.{MF18} Hardware failure (UL PLL Band 1). Cycle power once. If fault persists, replace the Hub{ML19} Commanded Out-of-service (Band 1). Band 1 commanded out-of-service by User.{MF20} Hardware failure (UL1 LO2 Band 1). Cycle power once. If the fault persists, replace the Hub.{MF21} Problem detected in the Hub. Contact TE Support for more information.{MF22} Problem detected in the Hub. Contact TE Support for more information.{MF23} Problem detected in the Hub Contact TE Support for more information.{MF24} Problem detected in the Hub. Contact TE Support for more information.{MF25} Hardware failure (DL PLL Band 2). Cycle power once. If fault persists, replace the Hub.
Faults Reported by Main HubsInterReach Fusion Wideband Installation, Operation, and Reference Manual Page 211D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013 © 2013 TE Connectivity Ltd.{MF26} Hardware failure (UL PLL Band 2). Cycle power once. If fault persists, replace the Hub.{ML27} Commanded Out-of-service (Band 2). Band 2 commanded out-of-service by User.{MF28} Problem detected in the Hub. Contact TE Support for more information.{MF29} Problem detected in the Hub. Contact TE Support for more information.{MF30} Problem detected in the Hub. Contact TE Support for more information.{MF31} Problem detected in the Hub. Contact TE Support for more information.{MF32} Problem detected in the Hub. Contact TE Support for more information.{MF33} Hardware failure (DL PLL Band 3). Cycle power once. If fault persists, replace the Hub.{MF34} Hardware failure (UL PLL Band 3). Cycle power once. If fault persists, replace the Hub.{ML35} Commanded Out-of-service (Band 3). Band 3 commanded out-of-service by User.{MF36} Hardware failure (638 MHz PLL). Cycle power once. If fault persists, replace the Hub.{MF37} Hardware failure (638 MHz PLL). Cycle power once. If fault persists, replace the Hub.{MF38} Problem detected in the Hub. Contact TE Support for more information.{MF39} Problem detected in the Hub. Contact TE Support for more information.{MF40} Problem detected in the Hub. Contact TE Support for more information.{MF41} Hardware failure (Optical Power Out). Cycle power once. If the fault persists, replace the Hub.{MF42} Unable to sync with TDD frame (Band 1). Check input signal and/or user TDD settings.{MF43} Unable to sync with TDD frame (Band 2). Check input signal and/or user TDD settings.{MF44} Problem detected in the Hub. Contact TE Support for more information{MF45} Problem detected in the Hub. Contact TE Support for more information.{MF46} Problem detected in the Hub. Contact TE Support for more information.{MF47} Problem detected in the Hub Contact TE Support for more information.{MF48} Problem detected in the Hub. Contact TE Support for more information.{MD129} Port 1 Disconnected. Unit is disconnected.{MD130} Port 2 Disconnected. Unit is disconnected.{MD131} Port 3 Disconnected. Unit is disconnected.{MD132} Port 4 Disconnected. Unit is disconnected.{MD133} Port 5 Disconnected. Unit is disconnected.{MD134} Port 6 Disconnected. Unit is disconnected.{MD135} Port 7 Disconnected. Unit is disconnected.{MD136} Port 8 Disconnected. Unit is disconnected.{MC137} Port 1 No Communications. No communications with remote unit.{MC138} Port 2 No Communications. No communications with remote unit.{MC139} Port 3 No Communications. No communications with remote unit.{MC140} Port 4 No Communications. No communications with remote unit.{MC141} Port 5 No Communications. No communications with remote unit.{MC142} Port 6 No Communications. No communications with remote unit.{MC143} Port 7 No Communications. No communications with remote unit.{MC144} Port 8 No Communications. No communications with remote unit.{MT145} Port 1 Cable Fault. Possible electrical short in the coax cable, or RAU problem.Table98.FaultMessagesforMainHubs(Cont.)Message NumberDescription Reason/Action
Appendix C: Faults, Warnings, Status Tables for Fusion, Fusion Wideband, Fusion SingleStar Page 212 InterReach Fusion Wideband Installation, Operation, and Reference Manual© 2013 TE Connectivity Ltd D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013{MT146} Port 2 Cable Fault. Possible electrical short in the coax cable, or RAU problem.{MT147} Port 3 Cable Fault. Possible electrical short in the coax cable, or RAU problem.{MT148} Port 4 Cable Fault. Possible electrical short in the coax cable, or RAU problem.{MT149} Port 5 Cable Fault. Possible electrical short in the coax cable, or RAU problem.{MT150} Port 6 Cable Fault. Possible electrical short in the coax cable, or RAU problem.{MT151} Port 7 Cable Fault. Possible electrical short in the coax cable, or RAU problem.{MT152} Port 8 Cable Fault. Possible electrical short in the coax cable, or RAU problem.{MT153} Port 1 Trip. Remote Unit is drawing too much current.{MT154} Port 2 Trip. Remote Unit is drawing too much current.{MT155} Port 3 Trip. Remote Unit is drawing too much current.{MT156} Port 4 Trip. Remote Unit is drawing too much current.{MT157} Port 5 Trip. Remote Unit is drawing too much current.{MT158} Port 6 Trip. Remote Unit is drawing too much current.{MT159} Port 7 Trip. Remote Unit is drawing too much current.{MT160} Port 8 Trip. Remote Unit is drawing too much current.{MF161} Problem detected in the Hub. Contact TE Support for more information.{MF162} Problem detected in the Hub. Contact TE Support for more information.{MF163} Problem detected in the Hub. Contact TE Support for more information.{MF164} Problem detected in the Hub. Contact TE Support for more information.{MF165} Problem detected in the Hub. Contact TE Support for more information.{MF166} Problem detected in the Hub. Contact TE Support for more information.{MF167} Problem detected in the Hub. Contact TE Support for more information.{MF168} Problem detected in the Hub. Contact TE Support for more information.{MF169} Problem detected in the Hub. Contact TE Support for more information.{MF170} Problem detected in the Hub. Contact TE Support for more information.{MF171} Problem detected in the Hub. Contact TE Support for more information.{MF172} Problem detected in the Hub. Contact TE Support for more information.{MF173} Problem detected in the Hub. Contact TE Support for more information.{MF174} Problem detected in the Hub. Contact TE Support for more information.{MF175} Problem detected in the Hub. Contact TE Support for more information.{MF176} Problem detected in the Hub. Contact TE Support for more information.Table98.FaultMessagesforMainHubs(Cont.)Message NumberDescription Reason/Action
Faults Reported for System CPUInterReach Fusion Wideband Installation, Operation, and Reference Manual Page 213D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013 © 2013 TE Connectivity Ltd.FAULTSREPORTEDFORSYSTEMCPUTable99.FaultsforSystemCPUMessage NumberDescription Reason/Action{SF01} No internal communications. No internal communications in preceding 2 minutes. Power cycle to clear.{SF02} Unable to open file (sysinfo). System CPU rebooted.{SF03} Unable to open file (sysstat). System CPU rebooted.{SF04} Invalid internal response. System CPU rebooted, internal command does not return valid response after 4 retries.{SF05} No MAC address. System CPU rebooted, unable to read MAC address from the Ethernet driver.{SF06} Unable to open file (sysinfo_org). System CPU rebooted.{SF07} Unable to open file (sbc_status). System CPU rebooted.{SF08} Invalid internal field response. System CPU rebooted, internal command format invalid.{SF09} Unable to open file (fileTTL). System CPU rebooted.{SF10} Invalid internal ASCII response. System CPU rebooted, illegal number of bytes.{SF11} Unable to open file (sysalarm). System CPU rebooted.{SF12} Unable to open file (password_etb). System CPU rebooted.{SF13} Unable to open file (CRC). System CPU rebooted.{SF14} Problem detected in the System CPU. Contact TE Support for more information.{SF15} pThread not executing. System CPU rebooted.{SF16} Problem detected in the System CPU. Contact TE Support for more information.{SF17} Problem detected in the System CPU. Contact TE Support for more information.{SF18} Problem detected in the System CPU. Contact TE Support for more information.{SF19} Problem detected in the System CPU. Contact TE Support for more information.{SF20} Problem detected in the System CPU. Contact TE Support for more information.{SF21} Problem detected in the System CPU. Contact TE Support for more information.{SF22} Problem detected in the System CPU. Contact TE Support for more information.{SF23} Problem detected in the System CPU. Contact TE Support for more information.{SF24} Problem detected in the System CPU. Contact TE Support for more information.{SF25} Problem detected in the System CPU. Contact TE Support for more information.{SF26} Problem detected in the System CPU. Contact TE Support for more information.{SF27} Problem detected in the System CPU. Contact TE Support for more information.{SF28} Problem detected in the System CPU. Contact TE Support for more information.{SF29} Problem detected in the System CPU. Contact TE Support for more information.{SF30} Problem detected in the System CPU. Contact TE Support for more information.{SF31} Problem detected in the System CPU. Contact TE Support for more information.{SF32} Problem detected in the System CPU. Contact TE Support for more information.
Appendix C: Faults, Warnings, Status Tables for Fusion, Fusion Wideband, Fusion SingleStar Page 214 InterReach Fusion Wideband Installation, Operation, and Reference Manual© 2013 TE Connectivity Ltd D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013FAULTSFOREXPANSIONHUBSTable100.FaultMessagesforExpansionHubsMessage NumberDescription Reason/Action{EF01} Software error occurred and recovered. If this happens repeatedly, replace the Hub.{EF02} Software reset occurred and recovered, or firmware download.If this happens repeatedly, replace the Hub.{EF03} Software reset occurred and recovered. If this happens repeatedly, replace the Hub.{EF04} Software reset occurred and recovered. If this happens repeatedly, replace the Hub.{EF05} Software error occurred and recovered. If this happens repeatedly, replace the Hub.{EF06} Firmware download. Firmware download.{EF07} Hub power cycle. Hub power cycle.{EF08} MH communications failure. No communications from MH in THE preceding 90 seconds.{EF09} MH communications failure. EH uplink messages not getting to the MH.{EF10} Hardware failure (PLL). Cycle power once. If the fault persists, replace the Hub.{EF11} Hardware failure (54 VDC). 54 VDC power supply is out of range, replace the Hub.{EF12} Problem detected in the EH. Contact TE Support for more information.{EF13} Band not programmed. Cycle power once. If the fault persists, replace the Hub.{EF14} Low optical input power. Check downlink fiber connections.{EF15} Hardware failure (Optical Output Power). Cycle power once. If the fault persists, replace the Hub.{EF16} Self Lockout (All Bands). The Hub has shutdown the system due to an internal fault. The system is offline.{EF17} Commanded Out-of-service (Band 1). Band 1 commanded out-of-service by the user.{EF18} Fault lockout (Band 1). Band 1 out-of-service due to an MH fault.{EF19} Problem detected in the EH. Contact TE Support for more information.{EF20} Problem detected in the EH. Contact TE Support for more information.{EF21} Problem detected in the EH. Contact TE Support for more information.{EF22} Problem detected in the EH. Contact TE Support for more information.{EF23} Problem detected in the EH. Contact TE Support for more information.{EF24} Problem detected in the EH. Contact TE Support for more information.{EF25} Commanded Out-of-service (Band 2). Band 2 commanded out-of-service by the user.{EF26} Fault lockout (Band 2). Band 2 out-of-service due to MH fault.{EF27} Problem detected in the EH. Contact TE Support for more information.{EF28} Problem detected in the EH. Contact TE Support for more information.{EF29} Problem detected in the EH. Contact TE Support for more information.{EF30} Problem detected in the EH. Contact TE Support for more information.{EF31} Problem detected in the EH. Contact TE Support for more information.{EF32} Problem detected in the EH. Contact TE Support for more information.{EF33} Commanded Out-of-service (Band 3). Band 3 commanded out-of-service by the user.{EF34} Fault lockout (Band 3). Band 3 out-of-service due to an MH fault.{EF35} Problem detected in the EH. Contact TE Support for more information.{EF36} Problem detected in the EH. Contact TE Support for more information.
Faults for Expansion HubsInterReach Fusion Wideband Installation, Operation, and Reference Manual Page 215D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013 © 2013 TE Connectivity Ltd.{EF37} Problem detected in the EH. Contact TE Support for more information.{EF38} Problem detected in the EH. Contact TE Support for more information.{EF39} Problem detected in the EH. Contact TE Support for more information.{EF40} Problem detected in the EH. Contact TE Support for more information.{ED129} Port 1 Disconnected. Unit is disconnected.{ED130} Port 2 Disconnected. Unit is disconnected.{ED131} Port 3 Disconnected. Unit is disconnected.{ED132} Port 4 Disconnected. Unit is disconnected.{ED133} Port 5 Disconnected. Unit is disconnected.{ED134} Port 6 Disconnected. Unit is disconnected.{ED135} Port 7 Disconnected. Unit is disconnected.{ED136} Port 8 Disconnected. Unit is disconnected.{EC137} Port 1 No Communications. No communications with remote unit.{EC138} Port 2 No Communications. No communications with remote unit.{EC139} Port 3 No Communications. No communications with remote unit.{EC140} Port 4 No Communications. No communications with remote unit.{EC141} Port 5 No Communications. No communications with remote unit.{EC142} Port 6 No Communications. No communications with remote unit.{EC143} Port 7 No Communications. No communications with remote unit.{EC144} Port 8 No Communications. No communications with remote unit.{ET145} Port 1 Cable Fault. Possible electrical short in the coaxial cable, or an RAU problem.{ET146} Port 2 Cable Fault. Possible electrical short in the coaxial cable, or an RAU problem.{ET147} Port 3 Cable Fault. Possible electrical short in the coaxial cable, or an RAU problem.{ET148} Port 4 Cable Fault. Possible electrical short in the coaxial cable, or an RAU problem.{ET149} Port 5 Cable Fault. Possible electrical short in the coaxial cable, or an RAU problem.{ET150} Port 6 Cable Fault. Possible electrical short in the coaxial cable, or an RAU problem.{ET151} Port 7 Cable Fault. Possible electrical short in the coaxial cable, or an RAU problem.{ET152} Port 8 Cable Fault. Possible electrical short in the coaxial cable, or an RAU problem.{ET153} Port 1 Trip. The Remote Unit is drawing too much current.{ET154} Port 2 Trip. The Remote Unit is drawing too much current.{ET155} Port 3 Trip. The Remote Unit is drawing too much current.{ET156} Port 4 Trip. The Remote Unit is drawing too much current.{ET157} Port 5 Trip. The Remote Unit is drawing too much current.{ET158} Port 6 Trip. The Remote Unit is drawing too much current.{ET159} Port 7 Trip. The Remote Unit is drawing too much current.{ET160} Port 8 Trip. The Remote Unit is drawing too much current.Table100.FaultMessagesforExpansionHubs(Cont.)Message NumberDescription Reason/Action
Appendix C: Faults, Warnings, Status Tables for Fusion, Fusion Wideband, Fusion SingleStar Page 216 InterReach Fusion Wideband Installation, Operation, and Reference Manual© 2013 TE Connectivity Ltd D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013FAULTSFORRAUSTable101.FaultsforRAUsMessage NumberDescription Reason/Action{RF01} Software error occurred and recovered. If this happens repeatedly, replace the RAU.{RF02} Software error occurred and recovered. If this happens repeatedly, replace the RAU.{RF03} Software error occurred and recovered. If this happens repeatedly, replace the RAU.{RF04} Software reset occurred and recovered, or firmware download.If this happens repeatedly, replace the RAU.{RF05} Software error occurred and recovered. If this happens repeatedly, replace the RAU.{RF06} Problem detected in the RAU. Contact TE Support for more information.{RF07} RAU power cycle. RAU power cycle.{RF08} Problem detected in the RAU. Contact TE Support for more information.{RF09} Invalid band. The RAU doesn't support programmed band. Check the RAU type against the band programmed in the hub.{RF10} Low input DC voltage. Check the coaxial cable for high RF loss. Try another Hub port. If the fault persists, replace the RAU. If the fault clears, mark the Hub port as unusable and replace the Hub when possible.{RF11} Hardware Failure (DL PLL Band 1). Cycle power once. If the fault persists, replace the RAU.{RF12} Hardware Failure (DL PLL Band 2). Cycle power once. If the fault persists, replace the RAU.{RF13} Hardware Failure (DL PLL Band 3). Cycle power once. If the fault persists, replace the RAU.{RF14} Hardware Failure (UL PLL Band 1). Cycle power once. If the fault persists, replace the RAU.{RF15} Hardware Failure (UL PLL Band 2). Cycle power once. If the fault persists, replace the RAU.{RF16} Hardware Failure (UL PLL Band 3). Cycle power once. If the fault persists, replace the RAU.{RF17} Hardware Failure (PA Band 1). Cycle power once. If the fault persists, replace the RAU.{RF18} Hardware Failure (PA Band 2). Cycle power once. If the fault persists, replace the RAU.{RF19} Hardware Failure (PA Band 3). Cycle power once. If the fault persists, replace the RAU.{RF20} Hardware Failure (UL Pilot). Cycle power once. If the fault persists, replace the RAU.{RL21} Commanded Out-of-service (Band 1). Band 1 commanded out-of-service by User. Command In-Service on Band 1 to restore service.{RL22} Commanded Out-of-service (Band 2). Band 2 commanded out-of-service by User. Command In-Service on Band 2 to restore service.{RL23} Commanded Out-of-service (Band 3). Band 3 commanded out-of-service by User. Command In-Service on Band 3 to restore service.{RF24} Problem detected in the RAU. Contact TE Support for more information.{RX25} Commanded shutdown (Band 1). Check the status of hub to which the RAU is connected.{RX26} Commanded shutdown (Band 2). Check the status of hub to which the RAU is connected.{RX27} Commanded shutdown (Band 3). Check the status of the hub to which the RAU is connected.{RF28} Internal shutdown (Band 1). RAU Fault condition in band 1 path (or common path).{RF29} Internal shutdown (Band 2). RAU Fault condition in band 2 path (or common path).{RF30} Internal shutdown (Band 3). RAU Fault condition in band 3 path (or common path).{RF31} Problem detected in the system. Contact TE Support for more information.{RF32} Problem detected in the RAU. Contact TE Support for more information.
Messages for Main HubsInterReach Fusion Wideband Installation, Operation, and Reference Manual Page 217D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013 © 2013 TE Connectivity Ltd.MESSAGESFORMAINHUBSWarningMessagesǤǤǡǤǡǤNOTE: AdminBrowserv000007orhigherdisplaysevents(faults,warnings,orstatusmessages)dependingonyourviewpreference.Tochangeyourviewpreference,refertoSection3.5,“Faults,Warnings,andStatusMessages”oftheFusionInstallation,Operation,andMaintenanceManual.StatusMessagesǡǤǡǤǤNOTE: AdminBrowserv000007orhigherdisplaysevents(faults,warnings,orstatusmessages)dependingonyourviewpreference.Tochangeyourviewpreference,refertoSection3.5,“Faults,Warnings,andStatusMessages”oftheFusionInstallation,Operation,andMaintenanceManual.NOTE: Theiconsdisplayedinthesystemstatustreeassumethattherearenootherfaults,warnings,orstatuspresent.ͳͲʹʹͳͺǡǣ[Mnn]/X• nn• X– S—– W—Ǥ
Appendix C: Faults, Warnings, Status Tables for Fusion, Fusion Wideband, Fusion SingleStar Page 218 InterReach Fusion Wideband Installation, Operation, and Reference Manual© 2013 TE Connectivity Ltd D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013Table102.Warnings/StatusMessagesforMainHubsMessage Number/DefaultDescription Reason/Action[M01]/S Fan 1 failure. Check the fan for rotation, air flow blockage, and dust. Replace the Hub on high temperature warning.[M02]/S Fan 2 failure. Check the fan for rotation, air flow blockage, and dust. Replace the Hub on high temperature warning.[M03]/S 54 VDC Pwr Supply Fan failure. Check the fan for rotation, air flow blockage, and dust. Replace the Hub on high temperature warning.[M04]/W 5 VDC Monitor. DC power out of range, replace the Hub.[M05]/W 9 VDC Monitor. DC power out of range, replace the Hub.[M06]/W 54 VDC Monitor. DC power out of range, replace the Hub.[M07]/W 3 VDC Monitor. DC power out of range, replace the Hub.[M08]/W 12 VDC Monitor. DC power out of range, replace the Hub.[M09]/W Temperature High. Reduce ambient temperature, check for air flow blockage, fan rotation.[M10]/W -5 VDC Monitor. DC power is out of range, replace the Hub.[M11]/W High laser current. Output laser failure possible, replace the Hub when possible.[M12]/W DL path loss is too high Replace the Hub.[M13]/S Low input optical (Port 1). Check the uplink fiber.[M14]/S Low input optical (Port 2). Check the uplink fiber.[M15]/S Low input optical (Port 3). Check the uplink fiber.[M16]/S Low input optical (Port 4). Check the uplink fiber.[M17]/S Hardware failure (Test Tone PLL Band 1). Unable to perform DL system test.[M18]/S Hardware failure (Test Tone Too High Band 1). Unable to perform DL system test.[M19]/S Hardware failure (Test Tone Too Low Band 1). Unable to perform DL system test.[M20]/W Overdrive limiter active (Band 1). Reduce input signal power to avoid potential component damage.[M21]/W CEMark limiter at maximum (Band 1). Reduce input signal power to avoid drop in system gain.[M22]/W No DL test tone (Band 1). Hub DL gain is low.[M23]/S No UL test tone (Band 1). Hub UL path gain is low.[M24]/S Problem detected in the system. Contact TE Support for more information.[M25]/S Hardware failure (Test Tone PLL Band 2). Unable to perform DL system test. Replace the hub when possible.[M26]/S Hardware failure (Test Tone Too High Band 2). Unable to perform DL system test. Replace the hub when possible.[M27]/S Hardware failure (Test Tone Too Low Band 2). Unable to perform DL system test. Replace the hub when possible.[M28]/W Overdrive limiter active (Band 2). Reduce input signal power to avoid potential component damage.[M29]/W CEMark limiter at maximum (Band 2). Reduce input signal power to avoid drop in system gain.[M30]/W No DL test tone (Band 2). Hub DL path gain is low.[M31]/S No UL test tone (Band 2). Hub UL path gain is low.[M32]/S Problem detected in the system. Contact TE Support for more information.[M33]/S Hardware failure (Test Tone PLL Band 3). Unable to perform DL system test.[M34]/S Hardware failure (Test Tone Too High Band 3). Unable to perform DL system test.[M35]/S Hardware failure (Test Tone Too Low Band 3). Unable to perform DL system test.[M36]/W Overdrive limiter active (Band 3). Reduce input signal power to avoid potential component damage.
Messages for Main HubsInterReach Fusion Wideband Installation, Operation, and Reference Manual Page 219D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013 © 2013 TE Connectivity Ltd.[M37]/W CEMark limiter at maximum (Band 3). Reduce input signal power to avoid drop in system gain.[M38]/W No DL test tone (Band 3). Hub DL path gain is low.[M39]/S No UL test tone (Band 3). Hub UL path gain is low.[M40]/S Problem detected in the Hub. Contact TE Support for more information.[M41]/W Port 1 No DL test tone (Band 1). Hub/Port DL path gain is low.[M42]/W Port 2 No DL test tone (Band 1). Hub/Port DL path gain is low.[M43]/W Port 3 No DL test tone (Band 1). Hub/Port DL path gain is low.[M44]/W Port 4 No DL test tone (Band 1). Hub/Port DL path gain is low.[M45]/W Port 5 No DL test tone (Band 1). Hub/Port DL path gain is low.[M46]/W Port 6 No DL test tone (Band 1). Hub/Port DL path gain is low.[M47]/W Port 7 No DL test tone (Band 1). Hub/Port DL path gain is low.[M48]/W Port 8 No DL test tone (Band 1). Hub/Port DL path gain is low.[M49]/W Port 1 No DL test tone (Band 2). Hub/Port DL path gain is low.[M50]/W Port 2 No DL test tone (Band 2). Hub/Port DL path gain is low.[M51]/W Port 3 No DL test tone (Band 2). Hub/Port DL path gain is low.[M52]/W Port 4 No DL test tone (Band 2). Hub/Port DL path gain is low.[M53]/W Port 5 No DL test tone (Band 2). Hub/Port DL path gain is low.[M54]/W Port 6 No DL test tone (Band 2). Hub/Port DL path gain is low.[M55]/W Port 7 No DL test tone (Band 2). Hub/Port DL path gain is low.[M56]/W Port 8 No DL test tone (Band 2). Hub/Port DL path gain is low.[M57]/W Port 1 No DL test tone (Band 3). Hub/Port DL path gain is low.[M58]/W Port 2 No DL test tone (Band 3). Hub/Port DL path gain is low.[M59]/W Port 3 No DL test tone (Band 3). Hub/Port DL path gain is low.[M60]/W Port 4 No DL test tone (Band 3). Hub/Port DL path gain is low.[M61]/W Port 5 No DL test tone (Band 3). Hub/Port DL path gain is low.[M62]/W Port 6 No DL test tone (Band 3). Hub/Port DL path gain is low.[M63]/W Port 7 No DL test tone (Band 3). Hub/Port DL path gain is low.[M64]/W Port 8 No DL test tone (Band 3). Hub/Port DL path gain is low.[M65]/S No UL test tone Port 1 (Band 1). Hub/Port UL path gain is low.[M66]/S No UL test tone Port 2 (Band 1). Hub/Port UL path gain is low.[M67]/S No UL test tone Port 3 (Band 1). Hub/Port UL path gain is low.[M68]/S No UL test tone Port 4 (Band 1). Hub/Port UL path gain is low.[M69]/S No UL test tone Port 1 (Band 2). Hub/Port UL path gain is low.[M70]/S No UL test tone Port 2 (Band 2). Hub/Port UL path gain is low.[M71]/S No UL test tone Port 3 (Band 2). Hub/Port UL path gain is low.[M72]/S No UL test tone Port 4 (Band 2). Hub/Port UL path gain is low.[M73]/S No UL test tone Port 1 (Band 3). Hub/Port UL path gain is low.[M74]/S No UL test tone Port 2 (Band 3). Hub/Port UL path gain is low.[M75]/S No UL test tone Port 3 (Band 3). Hub/Port UL path gain is low.Table102.Warnings/StatusMessagesforMainHubs(Cont.)Message Number/DefaultDescription Reason/Action
Appendix C: Faults, Warnings, Status Tables for Fusion, Fusion Wideband, Fusion SingleStar Page 220 InterReach Fusion Wideband Installation, Operation, and Reference Manual© 2013 TE Connectivity Ltd D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013[M76]/S No UL test tone Port 4 (Band 3). Hub/Port UL path gain is low.[M77]/S Problem detected in the Hub. Contact TE Support for more information.[M78]/S Problem detected in the Hub. Contact TE Support for more information.[M79]/S Problem detected in the Hub. Contact TE Support for more information.[M80]/S Problem detected in the Hub. Contact TE Support for more information.[M81]/W Port 1 DL path loss is high. If the problem is on more than one port, replace the Hub. Switch the cable connection to a different hub port until the Hub can be replaced.[M82]/W Port 2 DL path loss is high. If the problem is on more than one port, replace the Hub. Switch the cable connection to a different hub port until the Hub can be replaced.[M83]/W Port 3 DL path loss is high. If the problem is on more than one port, replace the Hub. Switch the cable connection to a different hub port until the Hub can be replaced.[M84]/W Port 4 DL path loss is high. If the problem is on more than one port, replace the Hub. Switch the cable connection to a different hub port until the Hub can be replaced.[M85]/W Port 5 DL path loss is high. If the problem is on more than one port, replace the Hub. Switch the cable connection to a different hub port until the Hub can be replaced.[M86]/W Port 6 DL path loss is high. If the problem is on more than one port, replace the Hub. Switch the cable connection to a different hub port until the Hub can be replaced.[M87]/W Port 7 DL path loss is high. If the problem is on more than one port, replace the Hub. Switch the cable connection to a different hub port until the Hub can be replaced.[M88]/W Port 8 DL path loss is high. If the problem is on more than one port, replace the Hub. Switch the cable connection to a different hub port until the Hub can be replaced.[M89]/W Port 1 UL path loss is high. Check the cable for high RF loss. Switch the cable connection to a different hub port. If the problem on more than one port, replace the Hub, otherwise replace the RAU.[M90]/W Port 2 UL path loss is high. Check the cable for high RF loss. Switch the cable connection to a different hub port. If the problem is on more than one port, replace the Hub, otherwise replace the RAU.[M91]/W Port 3 UL path loss is high. Check the cable for high RF loss. Switch the cable connection to a different hub port. If the problem is on more than one port, replace the Hub, otherwise replace the RAU.[M92]/W Port 4 UL path loss is high. Check the cable for high RF loss. Switch the cable connection to a different hub port. If the problem is on more than one port, replace the Hub, otherwise replace the RAU.[M93]/W Port 5 UL path loss is high. Check the cable for high RF loss. Switch the cable connection to a different hub port. If the problem is on more than one port, replace the Hub, otherwise replace the RAU.[M94]/W Port 6 UL path loss is high. Check the cable for high RF loss. Switch the cable connection to a different hub port. If the problem is on more than one port, replace the Hub, otherwise replace the RAU.Table102.Warnings/StatusMessagesforMainHubs(Cont.)Message Number/DefaultDescription Reason/Action
Messages for Main HubsInterReach Fusion Wideband Installation, Operation, and Reference Manual Page 221D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013 © 2013 TE Connectivity Ltd.[M95]/W Port 7 UL path loss is high. Check the cable for high RF loss. Switch the cable connection to a different hub port. If the problem is on more than one port, replace the Hub, otherwise replace the RAU.[M96]/W Port 8 UL path loss is high. Check the cable for high RF loss. Switch the cable connection to a different hub port. If the problem is on more than one port, replace the Hub, otherwise replace the RAU.[M97]/W Port 1 UL path exceeds maximum gain. If the problem is common to more than one port, replace the Hub, otherwise check the RAU.[M98]/W Port 2 UL path exceeds maximum gain. If the problem is common to more than one port, replace the Hub, otherwise check the RAU.[M99]/W Port 2 UL path exceeds maximum gain. If the problem is common to more than one port, replace the Hub, otherwise check the RAU.[M100]/W Port 2 UL path exceeds maximum gain. If the problem is common to more than one port, replace the Hub, otherwise check the RAU.[M101]/W Port 2 UL path exceeds maximum gain. If the problem is common to more than one port, replace the Hub, otherwise check the RAU.[M102]/W Port 2 UL path exceeds maximum gain. If the problem is common to more than one port, replace the Hub, otherwise check the RAU.[M103]/W Port 2 UL path exceeds maximum gain. If the problem is common to more than one port, replace the Hub, otherwise check the RAU.[M104]/W Port 8 UL path exceeds maximum gain. If the problem is common to more than one port, replace the Hub, otherwise check the RAU.[M105]/W Port 1 54 VDC Power Enabled. Caution: Port 54 VDC power may be present at the output.[M106]/W Port 2 54 VDC Power Enabled. Caution: Port 54 VDC power may be present at the output.[M107]/W Port 3 54 VDC Power Enabled. Caution: Port 54 VDC power may be present at the output.[M108]/W Port 4 54 VDC Power Enabled. Caution: Port 54 VDC power may be present at the output.[M109]/W Port 5 54 VDC Power Enabled. Caution: Port 54 VDC power may be present at the output.[M110]/W Port 6 54 VDC Power Enabled. Caution: Port 54 VDC power may be present at the output.[M111]/W Port 7 54 VDC Power Enabled. Caution: Port 54 VDC power may be present at the output.[M112]/W Port 8 54 VDC Power Enabled. Caution: Port 54 VDC power may be present at the output.Table102.Warnings/StatusMessagesforMainHubs(Cont.)Message Number/DefaultDescription Reason/Action
Appendix C: Faults, Warnings, Status Tables for Fusion, Fusion Wideband, Fusion SingleStar Page 222 InterReach Fusion Wideband Installation, Operation, and Reference Manual© 2013 TE Connectivity Ltd D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013MESSAGESFORSYSTEMCPUSͳͲ͵ǡǣ[Snn]/X• nn• X– S—– W—ǤTable103.Warning/StatusMessagesforSystemCPUsMessage Number/DefaultDescription Reason/Action[S01]/W Alarm Input 1. Check equipment connected to alarm input 1.[S02]/W Alarm Input 2. Check equipment connected to alarm input 2.[S03]/W Alarm Input 3. Check equipment connected to alarm input 3.[S04]/S Performed System Test System has just performed system test.[S05]/S Problem detected in the System CPU. Contact TE Support for more information.[S06]/S Loaded default etb file. Contact TE Support for more information.[S07]/S Loaded default SBC status file. Contact TE Support for more information.[S08]/S Problem detected in the System CPU. Contact TE Support for more information.[S09]/S TTL is full. Retrieve the TTL and erase.[S10]/S Problem detected in the System CPU. Contact TE Support for more information.[S11]/S Problem detected in the System CPU. Contact TE Support for more information.[S12]/S Loaded default Password file. Contact TE Support for more information.[S13]/S Loaded default sys config file. Contact TE Support for more information.[S14]/S Communication retries exceeded. Attempted command three times without response.[S15]/S Problem detected in the System CPU. Contact TE Support for more information.[S16]/S Problem detected in the System CPU. Contact TE Support for more information.
Messages for Expansion HubsInterReach Fusion Wideband Installation, Operation, and Reference Manual Page 223D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013 © 2013 TE Connectivity Ltd.MESSAGESFOREXPANSIONHUBSTable104.Warning/StatusMessageforExpansionHubsMessage Number/DefaultDescription Reason/Action[E01]/W Alarm Input 1. Check the equipment connected to alarm input 1.[E02]/W Alarm Input 2. Check the equipment connected to alarm input 2.[E03]/W Alarm Input 3. Check the equipment connected to alarm input 3.[E04]/S Problem detected in the EH. Contact TE Support for more information.[E05]/W SNMP Trap #1. TBD.[E06]/W SNMP Trap #2. TBD.[E07]/W SNMP Trap #3. TBD.[E08]/S Problem detected in the EH. Contact TE Support for more information.[E09]/S Fan 1 failure. Check the fan for proper rotation, air flow blockage, and dust accumulation. Replace the Hub on high temperature warning.[E10]/S Fan 2 failure. Check the fan for proper rotation, air flow blockage, and dust accumulation. Replace the Hub on high temperature warning.[E11]/W -5 VDC Monitor. DC power out of range, replace the Hub.[E12]/W 5 VDC Monitor. DC power out of range, replace the Hub.[E13]/W 9 VDC Monitor. DC power out of range, replace the Hub.[E14]/W 54 VDC Pwr Supply failure. DC port power supply out of range, replace the Hub.[E15]/W 3 VDC Monitor. DC power out of range, replace the Hub.[E16]/W 12 VDC Monitor. DC power out of range, replace the Hub.[E17]/W Temperature High. Reduce the ambient temperature, check for air flow blockage, fan rotation.[E18]/W DL path exceeds maximum gain. If the problem is common to more than one port, replace the MH, otherwise check the EH.[E19]/W DL path loss is high. Check the cable for high RF loss. Switch the cable connection to a different MH port. If the problem is on more than one port, replace the EH, otherwise replace the RAU.[E20]/W Hardware Failure (High UL Pilot). Cycle power once. If the fault persists, replace the EH.[E21]/W Hardware Failure (Low UL Pilot). Cycle power once. If the fault persists, replace the EH.[E22]/W Low optical input power. Check the downlink fiber connection.[E23]/W High laser current. Contact TE Support for more information.[E24]/S Problem detected in the EH. Contact TE Support for more information.[E25]/W Port 1 No DL test tone (Band 1). Hub/Port DL path gain is low.[E26]/W Port 2 No DL test tone (Band 1). Hub/Port DL path gain is low.[E27]/W Port 3 No DL test tone (Band 1). Hub/Port DL path gain is low.[E28]/W Port 4 No DL test tone (Band 1). Hub/Port DL path gain is low.[E29]/W Port 5 No DL test tone (Band 1). Hub/Port DL path gain is low.[E30]/W Port 6 No DL test tone (Band 1). Hub/Port DL path gain is low.[E31]/W Port 7 No DL test tone (Band 1). Hub/Port DL path gain is low.[E32]/W Port 8 No DL test tone (Band 1). Hub/Port DL path gain is low.[E33]/W Port 1 No DL test tone (Band 2). Hub/Port DL path gain is low.[E34]/W Port 2 No DL test tone (Band 2). Hub/Port DL path gain is low.
Appendix C: Faults, Warnings, Status Tables for Fusion, Fusion Wideband, Fusion SingleStar Page 224 InterReach Fusion Wideband Installation, Operation, and Reference Manual© 2013 TE Connectivity Ltd D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013[E35]/W Port 3 No DL test tone (Band 2). Hub/Port DL path gain is low.[E36]/W Port 4 No DL test tone (Band 2). Hub/Port DL path gain is low.[E37]/W Port 5 No DL test tone (Band 2). Hub/Port DL path gain is low.[E38]/W Port 6 No DL test tone (Band 2). Hub/Port DL path gain is low.[E39]/W Port 7 No DL test tone (Band 2). Hub/Port DL path gain is low.[E40]/W Port 8 No DL test tone (Band 2). Hub/Port DL path gain is low.[E41]/W Port 1 No DL test tone (Band 3). Hub/Port DL path gain is low.[E42]/W Port 2 No DL test tone (Band 3). Hub/Port DL path gain is low.[E43]/W Port 3 No DL test tone (Band 3). Hub/Port DL path gain is low.[E44]/W Port 4 No DL test tone (Band 3). Hub/Port DL path gain is low.[E45]/W Port 5 No DL test tone (Band 3). Hub/Port DL path gain is low.[E46]/W Port 6 No DL test tone (Band 3). Hub/Port DL path gain is low.[E47]/W Port 7 No DL test tone (Band 3). Hub/Port DL path gain is low.[E48]/W Port 8 No DL test tone (Band 3). Hub/Port DL path gain is low.[E49]/W Port 1 DL path loss is high. If the problem is on more than one port, replace the Hub. Switch the cable connection to a different hub port until the Hub can be replaced.[E50]/W Port 2 DL path loss is high. If the problem is on more than one port, replace the Hub. Switch the cable connection to a different hub port until the Hub can be replaced.[E51]/W Port 3 DL path loss is high. If the problem is on more than one port, replace the Hub. Switch the cable connection to a different hub port until the Hub can be replaced.[E52]/W Port 4 DL path loss is high. If the problem is on more than one port, replace the Hub. Switch the cable connection to a different hub port until the Hub can be replaced.[E53]/W Port 5 DL path loss is high. If the problem is on more than one port, replace the Hub. Switch the cable connection to a different hub port until the Hub can be replaced.[E54]/W Port 6 DL path loss is high. If the problem is on more than one port, replace the Hub. Switch the cable connection to a different hub port until the Hub can be replaced.[E55]/W Port 7 DL path loss is high. If the problem is on more than one port, replace the Hub. Switch the cable connection to a different hub port until the Hub can be replaced.[E56]/W Port 8 DL path loss is high. If the problem is on more than one port, replace the Hub. Switch the cable connection to a different hub port until the Hub can be replaced.[E57]/W Port 1 UL path loss is high. Check the cable for high RF loss. Switch the cable connection to a different hub port. If the problem is on more than one port, replace the Hub, otherwise replace the RAU.[E58]/W Port 2 UL path loss is high. Check the cable for high RF loss. Switch the cable connection to a different hub port. If the problem is on more than one port, replace the Hub, otherwise replace the RAU.[E59]/W Port 3 UL path loss is high. Check the cable for high RF loss. Switch the cable connection to a different hub port. If the problem is on more than one port, replace the Hub, otherwise replace the RAU.[E60]/W Port 4 UL path loss is high. Check the cable for high RF loss. Switch the cable connection to a different hub port. If the problem is on more than one port, replace the Hub, otherwise replace the RAU.[E61]/W Port 5 UL path loss is high. Check the cable for high RF loss. Switch the cable connection to a different hub port. If the problem is on more than one port, replace the Hub, otherwise replace the RAU.Table104.Warning/StatusMessageforExpansionHubs(Cont.)Message Number/DefaultDescription Reason/Action
Messages for Expansion HubsInterReach Fusion Wideband Installation, Operation, and Reference Manual Page 225D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013 © 2013 TE Connectivity Ltd.[E62]/W Port 6 UL path loss is high. Check the cable for high RF loss. Switch the cable connection to a different hub port. If the problem is on more than one port, replace the Hub, otherwise replace the RAU.[E63]/W Port 7 UL path loss is high. Check the cable for high RF loss. Switch the cable connection to a different hub port. If the problem is on more than one port, replace the Hub, otherwise replace the RAU.[E64]/W Port 8 UL path loss is high. Check the cable for high RF loss. Switch the cable connection to a different hub port. If the problem is on more than one port, replace the Hub, otherwise replace the RAU.[E65]/W Port 1 UL path exceeds maximum gain. If the problem is common to more than one port, replace the Hub, otherwise check RAU.[E66]/W Port 2 UL path exceeds maximum gain. If the problem is common to more than one port, replace the Hub, otherwise check RAU.[E67]/W Port 3 UL path exceeds maximum gain. If the problem is common to more than one port, replace the Hub, otherwise check RAU.[E68]/W Port 4 UL path exceeds maximum gain. If the problem is common to more than one port, replace the Hub, otherwise check RAU.[E69]/W Port 5 UL path exceeds maximum gain. If the problem is common to more than one port, replace the Hub, otherwise check RAU.[E70]/W Port 6 UL path exceeds maximum gain. If the problem is common to more than one port, replace the Hub, otherwise check RAU.[E71]/W Port 7 UL path exceeds maximum gain. If problem is common to more than one port, replace the Hub, otherwise check RAU.[E72]/W Port 8 UL path exceeds maximum gain. If the problem is common to more than one port, replace the Hub, otherwise check RAU.[E73]/W Port 1 54 VDC Power Enabled. Caution: Port 54 VDC power may be present at the output.[E74]/W Port 2 54 VDC Power Enabled. Caution: Port 54 VDC power may be present at the output.[E75]/W Port 3 54 VDC Power Enabled. Caution: Port 54 VDC power may be present at the output.[E76]/W Port 4 54 VDC Power Enabled. Caution: Port 54 VDC power may be present at the output.[E77]/W Port 5 54 VDC Power Enabled. Caution: Port 54 VDC power may be present at the output.[E78]/W Port 6 54 VDC Power Enabled. Caution: Port 54 VDC power may be present at the output.[E79]/W Port 7 54 VDC Power Enabled. Caution: Port 54 VDC power may be present at the output.[E80]/W Port 8 54 VDC Power Enabled. Caution: Port 54 VDC power may be present at the output.Table104.Warning/StatusMessageforExpansionHubs(Cont.)Message Number/DefaultDescription Reason/Action
Appendix C: Faults, Warnings, Status Tables for Fusion, Fusion Wideband, Fusion SingleStar Page 226 InterReach Fusion Wideband Installation, Operation, and Reference Manual© 2013 TE Connectivity Ltd D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013MESSAGESFORRAUSͳͲͷǡǣ[Rnn]/X• nn• X– S—– W—ǤTable105.Warning/StatusMessagesforRAUsMessage NumberDefaultDescription Reason/Action[R01]/W Temperature High. Check RAU location for excessive temperature; check for air flow blockage and/or incorrect installation. Move the RAU to a cooler environment.[R02]/W No communications from Hub. Check the cable for high RF loss. Switch the cable connection to a different hub port. If the problem persists, replace the RAU.[R03]/W DL RF path loss is too high. Check the cable for high RF loss. Switch the cable connection to a different hub port. If the problem persists, replace the RAU.[R04]/W DL RF path exceeds maximum gain. Check the Hub for proper operation; switch the cable connection to a different hub port. If the problem persists, replace the RAU.[R05]/S DL RF path problem (Band 1). Unable to complete the DL system end-to-end test, replace the RAU when possible.[R06]/S DL RF path problem (Band 2). Unable to complete the DL system end-to-end test, replace the RAU when possible.[R07]/S DL RF path problem (Band 3). Unable to complete the DL system end-to-end test, replace the RAU when possible.[R08]/S System test required. Run system test.[R09]/W Antenna Disconnected. Check RAU antenna connection; re-run system test.[R10]/S UL RF path problem (Band 1). Unable to complete the UL system end-to-end test, replace the RAU when possible.[R11]/S UL RF path problem (Band 2). Unable to complete the UL system end-to-end test, replace the RAU when possible.[R12]/S UL RF path problem (Band 3). Unable to complete the UL system end-to-end test, replace the RAU when possible.[R13]/S Problem detected in the RAU. Contact TE Support for more information.[R14]/S Problem detected in the RAU. Contact TE Support for more information.[R15]/S Problem detected in the RAU. Contact TE Support for more information.[R16]/S Problem detected in the RAU. Contact TE Support for more information.[R17]/S Antenna disconnected (Band 1). Check the RAU Band 1 antenna, then rerun the system test.[R18]/S Antenna disconnected (Band 2). Check the RAU Band 2 antenna, then rerun the system test.[R19]/S Hardware Failure (UL FD PLL Band 1). Unable to complete a UL system end-to-end test. Replace the RAU when possible.[R20]/W TDD signaling tone outside valid range (Band 1). If the Main Hub and Expansion Hub are okay, replace the RAU.
Messages for RAUsInterReach Fusion Wideband Installation, Operation, and Reference Manual Page 227D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013 © 2013 TE Connectivity Ltd.[R21]/W TDD signaling tone outside valid range (Band 2). If the Main Hub and Expansion Hub are okay, replace the RAU.[R22]/S High PA current (Band 1). The unit is operating with reduced gain. Verify that the input signal is at the appropriate level. If the problem persists, replace the RAU when possible.[R23]/S High PA current (Band 2). The unit is operating with reduced gain. Verify that the input signal is at the appropriate level. If the problem persists, replace the RAU when possible.Table105.Warning/StatusMessagesforRAUs(Cont.)Message NumberDefaultDescription Reason/Action
Appendix C: Faults, Warnings, Status Tables for Fusion, Fusion Wideband, Fusion SingleStar Page 228 InterReach Fusion Wideband Installation, Operation, and Reference Manual© 2013 TE Connectivity Ltd D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
InterReach Fusion Wideband Installation, Operation, and Reference Manual Page 229D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013 ©2013 TE Connectivity Ltd.APPENDIXD:CONTACTINGTECONNECTIVITYContactingTEConnectivitybyTelephoneOnlineAccesstoTEConnectivitySalesAsia Pacific +65-6294-9948France 0800 914032Germany 0180 2232923Italy 0800 782374Spain 900 983291United Kingdom 0800 960236USA or Canada 1-800-366-3891Extension 73000Connectivity Extension 73475Wireless Extension 73476Technical SupportUSA or Canada 1-800-530-9960Elsewhere +1-952-917-0761Customer Portalhttps://www.te.com/commerce/uso/myaccount.doTechnical Support for Wireless Productshttp://www.te.com/WirelessSupport
Appendix D: Contacting TE Connectivity Page 230 InterReach Fusion Wideband Installation, Operation, and Reference Manual© 2013 TE Connectivity Ltd D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
www.te.com/wireless

Navigation menu