ADC Telecommunications F0689-011 InterReach Fusion 700 MHz (Upper C) , AWS MIMO HP User Manual FusionWideband IOR Issue7 Pages 128 240

Download:
Mirror Download [FCC.gov]
Document ID	1971753
Application ID	4g2MbsbRvVrvmSekuzga1Q==
Document Description	NOOF0689011 User Manual Part 2
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	200.52kB (2506530 bits)
Date Submitted	2013-05-23 00:00:00
Date Available	2013-06-25 00:00:00
Creation Date	2013-05-23 08:59:21
Producing Software	GPL Ghostscript 8.64
Document Lastmod	2013-05-23 08:59:21
Document Title	FusionWideband_IOR_Issue7_Pages_128_240.pdf
Document Creator	PDFCreator Version 0.9.8
Document Author:	te100572

Installing Expansion Hubs
––ƒ Š–Š‡ —„–‘–Š‡™ƒŽŽ•‘–Š‡‘—–‹‰„”ƒ ‡–•ƒ”‡‘”‹‡–ƒ–‡†ƒ––Š‡–‘’ƒ†„‘––‘‘ˆ
–Š‡™ƒŽŽ‘—–‡†Š—„Ǥȋ‡ˆ‡”–‘ ‹‰—”‡͵͹ǤȌ
Figure37.Installing Directly to the Wall
‡ƒ˜‡–Š‡†—•– ƒ’•‘–Š‡ˆ‹„‡”’‘”–•—–‹Ž›‘—ƒ”‡”‡ƒ†›–‘ ‘‡ ––Š‡ˆ‹„‡”‘’–‹  ƒ„Ž‡•Ǥ
3 InstallinganOptionalCableManagerintheRack
•‡–Š‡• ”‡™•’”‘˜‹†‡†–‘ˆƒ•–‡–Š‡ ƒ„Ž‡ƒƒ‰‡”–‘–Š‡”ƒ ǡ‹‡†‹ƒ–‡Ž›ƒ„‘˜‡‘”„‡Ž‘™–Š‡
š’ƒ•‹‘ —„Ǥ
3 PoweringontheExpansionHub
‘‡ ––Š‡‘”’‘™‡”ƒ•‡š’Žƒ‹‡†‹Dzƒ‹‰‘™‡”‘‡ –‹‘•dz‘’ƒ‰‡͹ǦͳͺǤ
—”‘–Š‡’‘™‡”–‘–Š‡š’ƒ•‹‘ —„ƒ† Š‡ –Šƒ–ƒŽŽ–Š‡Žƒ’•ƒ”‡ˆ— –‹‘‹‰
’”‘’‡”Ž›Ǥ
’‘’‘™‡”Ǧ—’ǡ–Š‡•„Ž‹•ˆ‘”ˆ‹˜‡•‡ ‘†•ƒ•ƒ˜‹•—ƒŽ Š‡ –Šƒ––Š‡›ƒ”‡ˆ— –‹‘‹‰Ǥ
ˆ–‡”–Š‡ˆ‹˜‡Ǧ•‡ ‘†–‡•–ǣ
•
•
•
•
Š‡POWERƒ†UL STATUS••Š‘—Ž†„‡‰”‡‡Ǥ
ˆ–Š‡—’Ž‹ˆ‹„‡”‹•‘– ‘‡ –‡†ǡ–Š‡UL STATUS –—”•”‡†‹†‹ ƒ–‹‰–Šƒ––Š‡”‡‹•‘
‘—‹ ƒ–‹‘™‹–Š–Š‡ƒ‹ —„Ǥ
Š‡E-HUB STATUSƒ†DL STATUS ••Š‘—Ž†„‡”‡†Ǥ
ŽŽ’‘”–••Š‘—Ž†„‡‘ˆˆ„‡ ƒ—•‡‘•ƒ”‡ ‘‡ –‡†›‡–Ǥ
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Page 129
Š 2013 TE Connectivity Ltd.
Installing Fusion Wideband
3 ConnectingtheFiberCablestotheExpansionHub
CAUTION!
ObserveallFiberPortSafetyPrecautionslistedin“SafetyPrecautions”onpage109.
PreparingtheFiberCables
‘ˆ‹”–Šƒ––Š‡‹”‘’–‹ ƒŽŽ‘••†‘‡•‘–‡š ‡‡†͵†‘’–‹ ƒŽ„—†‰‡–Ǥ‹•Ž‡••–ŠƒǦ͸Ͳ†Ǥ
ˆˆ‹„‡”†‹•–”‹„—–‹‘’ƒ‡Ž•ƒ”‡—•‡†ǡ ‘ˆ‹”–Šƒ––Š‡–‘–ƒŽ‘’–‹ ƒŽŽ‘••‘ˆˆ‹„‡” ƒ„Ž‡ǡˆ”‘–Š‡
ƒ‹ —„–Š”‘—‰Š†‹•–”‹„—–‹‘’ƒ‡Ž•ƒ†’ƒ– Š ‘”†•–‘–Š‡š’ƒ•‹‘ —„ǡ†‘‡•‘–‡š ‡‡†
–Š‡‘’–‹ ƒŽ„—†‰‡–Ǥ
ƒ‡•—”‡–Š‡ˆ‹„‡” ƒ„Ž‡ǯ• ‘‡ –‘”•ƒ”‡Ȁȋƒ‰Ž‡Ǧ’‘Ž‹•Š‡†ȌǤUsinganyother
connectortypewillresultindegradedsystemperformanceandmaydamagethe
equipment.ȋ‘— ƒ—•‡ƒȀ’‹‰–ƒ‹Ž‹ˆ–Š‡ˆ‹„‡” ƒ„Ž‡ǯ• ‘‡ –‘”•ƒ”‡‘–Ȁǡ
”‡ˆ‡”–‘Dz —•‹‘‹†‡„ƒ†’Ž‹ ‹‰‘ˆ ‹„‡”ƒ†‹‰–ƒ‹Ždz‘’ƒ‰‡ͳͶͷǡ‘””‡’Žƒ ‡–Š‡
‘‡ –‘”•ǤȌ
ConnectingtheFiberCables
Š‡ˆ‹„‡” ƒ„Ž‡‹•Žƒ„‡Ž‡†™‹–Š‡‹–Š‡”1‘”2ǡ‘”‹• ‘Ž‘”Ǧ ‘†‡†Ǥ ‘”’”‘’‡” ‘‡ –‹‘„‡–™‡‡–Š‡
ƒ‹ —„’‘”–•ƒ†–Š‡š’ƒ•‹‘ —„’‘”–•ǡ”‡ˆ‡”–‘–Š‡—„‡”‹‰‘” ‘Ž‘”Ǧ ‘†‡† ‘‡ –‹‘•
›‘—”‡ ‘”†‡†™Š‡‹•–ƒŽŽ‹‰–Š‡ƒ‹ —„ȋ•ȌǤ
IftheFiberJumperIsLabeledwith1or2
‘‡ –2–‘DOWNLINK‘–Š‡š’ƒ•‹‘ —„Ǥ
Š‡DL STATUS•Š‘—Ž†–—”‰”‡‡ƒ••‘‘ƒ•›‘— ‘‡ ––Š‡ˆ‹„‡”Ǥ ˆ‹–†‘‡•‘–ǡ–Š‡”‡‹•ƒ
†‘™Ž‹’”‘„Ž‡Ǥƒ‡•—”‡›‘—ƒ”‡ ‘‡ –‹‰–Š‡ ‘””‡ – ƒ„Ž‡–‘–Š‡’‘”–Ǥ
‘‡ –1–‘UPLINK‘š’ƒ•‹‘ —„Ǥ
Š‡UL STATUS–—”•‰”‡‡‘–Š‡ˆ‹”•–ƒ‹ —„ ‘—‹ ƒ–‹‘Ǥ –ƒ›–ƒ‡—’–‘ʹͲ
•‡ ‘†•–‘‡•–ƒ„Ž‹•Š ‘—‹ ƒ–‹‘Ǥ
Š‡š’ƒ•‹‘ —„ǯ•E-HUB STATUS–—”•‰”‡‡™Š‡–Š‡ƒ‹ —„•‡†•‹––Š‡ˆ”‡“—‡ ›
„ƒ† ‘ƒ†Ǥ
ˆ–Š‡UL STATUSƒ†E-HUB STATUS•†‘‘––—”‰”‡‡Ȁ‰”‡‡ǡ Š‡ –Š‡ƒ‹ —„•Ǣ
•‡‡–‡’ʹ‹ƒ„Ž‡ͺ͹‘’ƒ‰‡ͳʹ͸Ǥ
Page 130
Š 2013 TE Connectivity Ltd
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Installing Expansion Hubs
IftheFiberJumperIsColorͲCoded
‘‡ –Dz”‡†dz–‘DOWNLINK‘š’ƒ•‹‘ —„Ǥ
Š‡DL STATUS•Š‘—Ž†–—”‰”‡‡ƒ••‘‘ƒ•›‘— ‘‡ ––Š‡ˆ‹„‡”Ǥ ˆ‹–†‘‡•‘–ǡ–Š‡”‡‹•ƒ
†‘™Ž‹’”‘„Ž‡Ǥƒ‡•—”‡›‘—ƒ”‡ ‘‡ –‹‰–Š‡ ‘””‡ – ƒ„Ž‡–‘–Š‡’‘”–Ǥ
‘‡ –Dz„Ž—‡dz–‘UPLINK‘š’ƒ•‹‘ —„Ǥ
Š‡UL STATUS–—”•‰”‡‡‘–Š‡ˆ‹”•–ƒ‹ —„ ‘—‹ ƒ–‹‘Ǥ –ƒ›–ƒ‡—’–‘ʹͲ
•‡ ‘†•–‘‡•–ƒ„Ž‹•Š ‘—‹ ƒ–‹‘Ǥ
Š‡š’ƒ•‹‘ —„ǯ•E-HUB STATUS–—”•‰”‡‡™Š‡–Š‡ƒ‹ —„•‡†•‹––Š‡ˆ”‡“—‡ ›
„ƒ† ‘ƒ†Ǥ
ˆ–Š‡UL STATUSƒ†E-HUB STATUS•†‘‘––—”‰”‡‡Ȁ‰”‡‡ǡ Š‡ –Š‡ƒ‹ —„•Ǣ
•‡‡–‡’ʹ‹ƒ„Ž‡ͺ͹‘’ƒ‰‡ͳʹ͸Ǥ
3 Connectingthe75OhmCATVCables
‡”‹ˆ›–Šƒ––Š‡ ƒ„Ž‡Šƒ•„‡‡–‡•–‡†ƒ†–Š‡–‡•–”‡•—Ž–•ƒ”‡”‡ ‘”†‡†ǤŠ‹•‹ˆ‘”ƒ–‹‘‹•
”‡“—‹”‡†ˆ‘”–Š‡•Ǧ—‹Ž–‘ —‡–Ǥ
‡”‹ˆ›–Šƒ–‘Ž› ƒ’–‹˜‡ ‡–‡”’‹  ‘‡ –‘”•ƒ”‡—•‡†‘–Š‡•‘Ž‹† ‘’’‡” ‡–‡” ‘†— –‘”
 ƒ„Ž‡ˆ”‘‘ ‘’‡ȋ‘”‡“—‹˜ƒŽ‡–ȌǤ
‡”‹ˆ›–Šƒ––Š‡ ƒ„Ž‡‹•Žƒ„‡Ž‡†™‹–Šǣ
•
•
•
—•‹‘‹†‡„ƒ†š’ƒ•‹‘ —„’‘”–—„‡”„‡‹‰—•‡†
‹†‡–‹ˆ‹‡”
ƒ””‹‡”ȋˆ‘”—Ž–‹’Ž‡‘’‡”ƒ–‘”•›•–‡•Ȍ
‘‡ ––Š‡ ƒ„Ž‡•–‘–Š‡ ’‘”–•ƒ ‘”†‹‰–‘–Š‡Žƒ„‡Ž•‘–Š‡ ƒ„Ž‡•Ǥ
Š‡STATUS••Š‘—Ž†„‡‘ˆˆ„‡ ƒ—•‡–Š‡•ƒ”‡‘– ‘‡ –‡†ƒ––Š‡‘–Š‡”‡†‘ˆ–Š‡
 ƒ„Ž‡Ǥ
‡ ‘”†™Š‹ Š ƒ„Ž‡›‘—ƒ”‡ ‘‡ –‹‰–‘™Š‹ Š’‘”–ȋ–Šƒ–‹•ǡˆ”‘–Š‡Žƒ„‡Ž‘–Š‡ ƒ„Ž‡Ȍǡƒ•
–Š‹•‹ˆ‘”ƒ–‹‘‹•”‡“—‹”‡†ˆ‘”–Š‡•Ǧ—‹Ž–‘ —‡–Ǥ
‹‡Ǧ‘ˆˆ–Š‡ ƒ„Ž‡•‘”—•‡–Š‡‘’–‹‘ƒŽ ƒ„Ž‡ƒƒ‰‡”–‘ƒ˜‘‹††ƒƒ‰‹‰–Š‡ ‘‡ –‘”•
„‡ ƒ—•‡‘ˆ ƒ„Ž‡•–”ƒ‹Ǥ
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Page 131
Š 2013 TE Connectivity Ltd.
Installing Fusion Wideband
3 TroubleshootingExpansionHubLEDsDuringInstallation
•
•
ŽŽš’ƒ•‹‘ —„PORT•™‹–Š• ‘‡ –‡†•Š‘—Ž†‹†‹ ƒ–‡ ”‡‡Ȁ‡†ǤŠ‹•‹†‹ ƒ–‡•
–Šƒ––Š‡‹•’‘™‡”‡†‘ƒ† ‘—‹ ƒ–‹‘Šƒ•„‡‡‡•–ƒ„Ž‹•Š‡†Ǥ
Š‡š’ƒ•‹‘ —„UL STATUS•Š‘—Ž†„‡ ”‡‡Ǥ
Table88. TroubleshootingExpansionHubLEDsDuringInstallation
During
Installation
LED
State
Action
Impact
Off
Check AC power; make sure the
Expansion Hub power-on switch is
on; replace the Expansion Hub.
The Expansion Hub is not
powering on.
PORT
LEDs are on but didn’t
blink through all
states.
Replace the Expansion Hub.
The Microcontroller is not
resetting properly; flash
memory corrupted.
PORT
Flashing Red 
(6 PPM)
Port unusable; replace the
Expansion Hub when possible.
Current sensor fault; do not
use the port.
UL STATUS
Red, after power-up
blink
Replace the Expansion Hub.
The Expansion Hub laser is not
operational; no uplink between
the Expansion Hub and Main
Hub.
UL STATUS
Red
Check the Main Hub LEDs—refer to
Step 2 in Table 87 on page 126.
No communication with Main
Hub.
1 Expansion Hub POWER
power is On
and no RAUs
are connected
Use AdminBrowser to determine the
problem.
DL STATUS
Red
Check the downlink fiber for optical
power; verify that the cables are
connected to correct ports (that is,
uplink/downlink)
No downlink between the
Expansion Hub and Main Hub.
Check the Main Hub LEDs—refer to
Step 2 in Table 87 on page 126.
2 Expansion Hub PORT
power is On
and RAUs are
connected
PORT
PORT
Page 132
Š 2013 TE Connectivity Ltd
Off
Check the CATV cable.
Power is not getting to the
RAU.
Flashing Red 
(60 PPM)
Test the CATV cable. If the cable
tests OK, try another port. If the
second port’s LEDs are Red/Off,
replace the RAU. If the second RAU
doesn’t work; replace the Expansion
Hub.
Power levels to RAU are not
correct; communications are
not established.
Use AdminBrowser to determine the
problem.
RAU is off-line.
Red
If the second port works, flag
the first port as unusable;
replace EH when possible.
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Installing RAUs
INSTALLINGRAUS
CAUTION!
InstallRAUsinindoorlocationsonly.Donotconnectanantennathatisinstalledinanoutdoor
locationtoanRAU.Foroutdoorinstallations,aprotectiveenclosureisrequired.
NOTE:
Thefollowingproceduresassumethatthesystemisnewfromthefactoryandthatithasnot
beenprogrammedwithbands.IfyouarereplacingcomponentsinapreͲinstalledsystemwith
eithernewunitsorunitsthatmayalreadybeprogrammed(forexample,reͲusingunitsfrom
anothersystem),referto“ReplacingFusionWidebandComponents”onpage175.
3 InstallingRAUs
‘—–ƒŽŽ•‹–Š‡Ž‘ ƒ–‹‘•ƒ”‡†‘–Š‡ˆŽ‘‘”’Žƒ•Ǥ
•
•
•
•
•–ƒŽŽͺͲͲ‹ƒ†ͺͷͲȀͳͻͲͲ œ••‘–Šƒ––Š‡‹”ƒ–‡ƒ•™‹ŽŽ„‡•‡’ƒ”ƒ–‡†„›‡‘—‰Š
•’ƒ ‡–‘”‡†— ‡•‹‰ƒŽ‹–‡”ˆ‡”‡ ‡„‡–™‡‡–Š‡ͺͲͲƒ†ͺͷͲ„ƒ†•Ǥ‡ˆ‡”–‘DzͺͲͲȀͺͷͲ œ
•‘Žƒ–‹‘‡“—‹”‡‡–•dz‘’ƒ‰‡ͳ͵Ͷˆ‘””‡ ‘‡†‡††‹•–ƒ ‡„‡–™‡‡ƒ–‡ƒ•Ǥ
‘— ƒ’Žƒ ‡–Š‡—‹–ǡ™‹–Š‘—–‹–•ˆƒ•–‡‹‰Šƒ”†™ƒ”‡ǡ‘ƒˆŽƒ–•—”ˆƒ ‡ǡ•— Šƒ•ƒ•Š‡Žˆǡ†‡•ǡ
ƒ„‹‡–ǡ‘”ƒ›‘–Š‡”Š‘”‹œ‘–ƒŽ•—”ˆƒ ‡–Šƒ–ƒŽŽ‘™••–ƒ„Ž‡’Žƒ ‡‡–™‹–Š–Š‡‘—–‹‰„ƒ•‡
ˆƒ ‹‰†‘™–‘–Š‡‘—–‹‰•—”ˆƒ ‡Ǥ ‘”‘—–‹‰–‘‘–Š‡”Ž‘ ƒ–‹‘•ȋ–Šƒ–‹•ǡ™ƒŽŽ•ǡ ‡‹Ž‹‰•ǡ
’‘Ž‡•Ȍ–Š‡—•–„‡•‡ —”‡Ž›‘—–‡†—•‹‰–Š‡Ͷ•Ž‘––‡†‘—–‹‰Š‘Ž‡•’”‘˜‹†‡†™‹–Š
͓͸†‹ƒ‡–‡”ˆƒ•–‡‡”•ǤŠ‹•‡–Š‘†‘ˆ‘—–‹‰—•–•‡ —”‡Ž›Š‘Ž†ƒ‹‹—‘ˆ͹Ž„•ǤŽ‘ƒ†Ǥ
––ƒ Š–Š‡•‡ —”‡Ž›–‘ƒ•–ƒ–‹‘ƒ”›‘„Œ‡ –ȋ–Šƒ–‹•ǡƒ™ƒŽŽǡ’‘Ž‡ǡ‘” ‡‹Ž‹‰–‹Ž‡ȌǤ
‘”’”‘’‡”˜‡–‹Žƒ–‹‘ǣ
– ‡‡’ƒ–Ž‡ƒ•–͹͸ȋ͵‹ǤȌ Ž‡ƒ”ƒ ‡ƒ”‘—†–Š‡–‘‡•—”‡’”‘’‡”˜‡–‹‰Ǥ
– ‘‘–•–ƒ •‘–‘’‘ˆ‡ƒ Š‘–Š‡”Ǥ
– Ž™ƒ›•‘—––Š‡™‹–Š–Š‡•‘Ž‹†ˆƒ ‡ȋ ‘–ƒ‹‹‰–Š‡‘—–‹‰Š‘Ž‡•Ȍƒ‰ƒ‹•––Š‡
‘—–‹‰•—”ˆƒ ‡Ǥ
3 InstallingPassiveAntennas
‡ˆ‡”–‘–Š‡ƒ—ˆƒ –—”‡”ǯ•‹•–ƒŽŽƒ–‹‘‹•–”— –‹‘•–‘‹•–ƒŽŽ’ƒ••‹˜‡ƒ–‡ƒ•Ǥ
Location
ƒ••‹˜‡ƒ–‡ƒ•ƒ”‡—•—ƒŽŽ›‹•–ƒŽŽ‡†„‡Ž‘™–Š‡ ‡‹Ž‹‰Ǥ ˆ–Š‡›ƒ”‡‹•–ƒŽŽ‡†ƒ„‘˜‡–Š‡ ‡‹Ž‹‰ǡ›‘—
—•– ‘•‹†‡”–Š‡ƒ††‹–‹‘ƒŽŽ‘••†—‡–‘–Š‡ ‡‹Ž‹‰ƒ–‡”‹ƒŽ™Š‡‡•–‹ƒ–‹‰–Š‡ƒ–‡ƒ
‘˜‡”ƒ‰‡ƒ”‡ƒǤ
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Page 133
Š 2013 TE Connectivity Ltd.
Installing Fusion Wideband
800/850MHzIsolationRequirements
Š‡†‡’Ž‘›‹‰ƒ› •›•–‡ǡ‰‹˜‡•’‡ ‹ƒŽƒ––‡–‹‘–‘’”‡˜‡–‹‰”‡ ‡‹˜‡”„Ž‘ ‹‰‘”
†‡•‡•‹–‹œƒ–‹‘„›‘—–Ǧ‘ˆǦ„ƒ†–”ƒ•‹––‡”•Ǥ›’‹ ƒŽŽ›ǡ•Šƒ”’ˆ‹Ž–‡”•‹–Š‡”‡ ‡‹˜‡”ˆ”‘–Ǧ‡†™‹ŽŽ
”‡†— ‡–Š‡‹–‡”ˆ‡”‹‰–”ƒ•‹––‡”•–‘–‘Ž‡”ƒ„Ž‡Ž‡˜‡Ž•Ǥ •‡Ž‡ – ƒ•‡•ǡ–Š‡‹–‡”ˆ‡”‡”•ƒ›‘ —’›
ƒˆ”‡“—‡ ›„ƒ†–Šƒ–‹•†‹”‡ –Ž›ƒ†Œƒ ‡––‘–Š‡”‡ ‡‹˜‹‰„ƒ†ƒ† ƒ‘–„‡ƒ†‡“—ƒ–‡Ž›”‡Œ‡ –‡†
„›ˆ‹Ž–‡”‹‰ǤŠ‡‘Ž›”‡ ‘—”•‡‹–Š‡•‡•‹–—ƒ–‹‘•‹•–‘’”‘˜‹†‡•—ˆˆ‹ ‹‡–‹•‘Žƒ–‹‘„›’Š›•‹ ƒŽŽ›
•‡’ƒ”ƒ–‹‰–Š‡‹–‡”ˆ‡”‹‰–”ƒ•‹––‡”•ƒ†”‡ ‡‹˜‡”•Ǥ
‹‘ —’‹‡••’‡ –”—ƒ–„‘–ŠͺͲͲ œƒ†ͻͲͲ œȋšǣͺͷͳȂͺ͸ͻȀšǣͺͲ͸ȂͺʹͶƒ†
šǣͻ͵ͷȂͻͶͳȀšǣͺͻ͸ȂͻͲʹȌǡ™Š‹Ž‡–Š‡‡ŽŽ—Žƒ”ƒ† ƒ””‹‡”••Šƒ”‡ƒ•‹‰Ž‡ͺͷͲ œ„Ž‘ 
ȋšǣͺ͸ͻȂͺͻͶȀšǣͺʹͶȂͺͶͻȌǤŠ‡ ‘„‹ƒ–‹‘‘ˆ–Š‡•‡ˆ”‡“—‡ ›„ƒ†•ǡͺͲͲȀͻͲͲ œ‹ƒ†
ͺͷͲ œ‡ŽŽ—Žƒ”ǡ”‡•—Ž–‹—’Ž‹ȋ”‡ ‡‹˜‡Ȍ„ƒ†•–Šƒ–ƒ”‡ƒ†Œƒ ‡––‘†‘™Ž‹ȋ
–”ƒ•‹–Ȍ„ƒ†•Ǥ ‹‰—”‡͵ͺ†‡’‹ –•–Š‡•‡‡ƒ”Ž› ‘–‹‰—‘—•„ƒ†•ǡ™‹–Šƒ””‘™•‹†‹ ƒ–‹‰–Š‡
‹–‡”ˆ‡”‹‰†‘™Ž‹ƒ†”‡ ‡‹˜‹‰—’Ž‹„ƒ†•Ǥ
800/iDEN Uplink
850 Cellular Uplink
824
800/iDEN Downlink
849
851
850 Cellular Downlink
869
900/iDEN Uplink
894
896 - 902
Figure38.800/850 MHz Spectrum
•–ƒŽŽƒ–‹‘‘ˆƒ‹Ǧ„—‹Ž†‹‰†‹•–”‹„—–‡†ƒ–‡ƒ•›•–‡ȋȌ–‘’”‘˜‹†‡ ‘˜‡”ƒ‰‡ˆ‘”„‘–Š
ͺͲͲȀͻͲͲ œ‹ƒ†ͺͷͲ œ‡ŽŽ—Žƒ”—•–ƒ ‘—–ˆ‘”–Š‡•‡†‘™Ž‹Ǧ–‘Ǧ—’Ž‹
‹–‡”ˆ‡”‡ ‡‹••—‡•ƒ†’”‘˜‹†‡ƒ†‡“—ƒ–‡‹•‘Žƒ–‹‘Ǥ
‘ˆˆ‡”•–Š‡ˆ‘ŽŽ‘™‹‰‰—‹†‡Ž‹‡•–‘™ƒ”†ƒ Š‹‡˜‹‰–Š‡’”‘’‡”ƒ‘—–‘ˆ‹•‘Žƒ–‹‘™Š‡
†‡’Ž‘›‹‰ —•‹‘‹†‡„ƒ†’”‘†— –•Ǥ
>d
Band 1
800 MHz
Band 2/3
850/1900 MHz
Figure39.Fusion Wideband 800/850/1900 MHz RAU Antenna Placement Guideline
Page 134
Š 2013 TE Connectivity Ltd
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Installing RAUs
800MHziDENDownlinkand850MHzCellularUplink
ʹ œˆ”‡“—‡ ›‰ƒ’ȋͺͷͳȂͺͶͻ œȌ•‡’ƒ”ƒ–‡•–Š‡ͺͲͲ‹†‘™Ž‹ƒ†ͺͷͲ‡ŽŽ—Žƒ”
—’Ž‹ˆ”‡“—‡ ›„ƒ†•Ǥ‡ ƒ—•‡‘ˆ–Š‹•ƒ””‘™•’ƒ ‹‰ǡͺͲͲ‹†‘™Ž‹‹–‡”‘†—Žƒ–‹‘
’”‘†— –•ƒ›ˆƒŽŽ™‹–Š‹–Š‡ͺͷͲ‡ŽŽ—Žƒ”—’Ž‹„ƒ†Ǥ ƒ††‹–‹‘ǡͺͲͲ‹†‘™Ž‹•‹‰ƒŽ•
‡ƒ”–Š‡Ž‘™‡”‡†‰‡‘ˆ–Š‡„ƒ†ƒ–ͺͷͳ œƒ› ƒ—•‡–Š‡ͺͷͲ‡ŽŽ—Žƒ”—’Ž‹ƒ—–‘ƒ–‹ Ž‡˜‡Ž
‘–”‘ŽȋȌ ‹” —‹–”›‹–Š‡–‘‡‰ƒ‰‡ƒ†–Š‡”‡„›”‡†— ‡—’Ž‹‰ƒ‹Ǥ
‘’”‡˜‡–‡‹–Š‡”‘ˆ–Š‡•‡ ‘†‹–‹‘•ǡ—•‡–Š‡ˆ‘ŽŽ‘™‹‰‰—‹†‡Ž‹‡•ǣ
•
•
Ǧ„ƒ†ͺͲͲ‹‹–‡”‘†—Žƒ–‹‘’”‘†— –•δǦͻͲ†
‘™‡”ˆ”‡“—‡ ›ͺͲͲ‹•‹‰ƒŽ•δȂ͵Ͳ†ˆ‘” —•‹‘‹†‡„ƒ†
‹˜‡ƒ–›’‹ ƒŽ ‘ˆ‹‰—”ƒ–‹‘ȋͶ‹ ƒ””‹‡”•ǡ‘‹Ǧ†‹”‡ –‹‘ƒŽƒ–‡ƒ•ǡŽ‹‡‘ˆ•‹‰Š–Ȍǡ–Š‡•‡
‰—‹†‡Ž‹‡•–”ƒ•Žƒ–‡–‘ƒƒ–‡ƒ•’ƒ ‹‰ȋ†ͳȌ‘ˆ͸Ȃͻ‡–‡”•Ǥ
850MHzCellularDownlinkand900MHziDENUplink
ʹ œˆ”‡“—‡ ›‰ƒ’ȋͺͻ͸ȂͺͻͶ œȌ•‡’ƒ”ƒ–‡•–Š‡ͺͷͲ‡ŽŽ—Žƒ”†‘™Ž‹ƒ†ͻͲͲ‹
—’Ž‹ˆ”‡“—‡ ›„ƒ†•Ǥ‡ ƒ—•‡‘ˆ–Š‹•ƒ””‘™•’ƒ ‹‰ǡͺͷͲ‡ŽŽ—Žƒ”†‘™Ž‹‹–‡”‘†—Žƒ–‹‘
’”‘†— –•ƒ›ˆƒŽŽ™‹–Š‹–Š‡ͻͲͲ‹—’Ž‹„ƒ†Ǥ ƒ††‹–‹‘ǡͺͷͲ‡ŽŽ—Žƒ”†‘™Ž‹•‹‰ƒŽ•
‡ƒ”–Š‡—’’‡”‡†‰‡‘ˆ–Š‡„ƒ†ƒ–ͺͻͶ œƒ› ƒ—•‡–Š‡ͻͲͲ‹—’Ž‹–‘‡‰ƒ‰‡ƒ†
–Š‡”‡„›”‡†— ‡—’Ž‹‰ƒ‹Ǥ
‘’”‡˜‡–‡‹–Š‡”‘ˆ–Š‡•‡ ‘†‹–‹‘•ǡ—•‡–Š‡ˆ‘ŽŽ‘™‹‰‰—‹†‡Ž‹‡•ǣ
•
•
Ǧ„ƒ†ͺͷͲ‡ŽŽ—Žƒ”‹–‡”‘†—Žƒ–‹‘’”‘†— –•δǦͻͲ†
’’‡”ˆ”‡“—‡ ›ͺͷͲ‡ŽŽ—Žƒ”•‹‰ƒŽ•δȂ͵Ͳ†ˆ‘” —•‹‘‹†‡„ƒ†
‹˜‡ƒ–›’‹ ƒŽ ‘ˆ‹‰—”ƒ–‹‘ȋ͸ ƒ””‹‡”•ˆ‘” —•‹‘‹†‡„ƒ†ǡ‘‹Ǧ†‹”‡ –‹‘ƒŽ
ƒ–‡ƒ•ǡŽ‹‡‘ˆ•‹‰Š–Ȍǡ–Š‡•‡‰—‹†‡Ž‹‡•–”ƒ•Žƒ–‡–‘ƒƒ–‡ƒ•’ƒ ‹‰ȋ†ʹȌ‘ˆͺǦͳͶ‡–‡”•Ǥ
’ƒ ‹‰„‡–™‡‡• ǦͺͷͳͻǦͳƒ† ǦͺͲͻͲͳͻǦʹ•Š‘—Ž†„‡‹ƒ”ƒ‰‡‘ˆˆ”‘ͺ–‘ͳͶ
‡–‡”•Ǥ
3 ConnectingtheAntennatotheRAU
‘‡ –ƒ’ƒ••‹˜‡—Ž–‹Ǧ„ƒ†ƒ–‡ƒ–‘–Š‡ ‘‡ –‘”‘–Š‡—•‹‰ ‘ƒš‹ƒŽ ƒ„Ž‡™‹–Š–Š‡
Ž‡ƒ•–ƒ‘—–‘ˆŽ‘••’‘••‹„Ž‡Ǥ
CAUTION!
FirmlyhandͲtightentheNconnector–DONOToverͲtightentheconnector.
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Page 135
Š 2013 TE Connectivity Ltd.
Installing Fusion Wideband
3 ConnectingtheCATVCable
‡”‹ˆ›–Šƒ––Š‡ ƒ„Ž‡Šƒ•„‡‡–‡•–‡†ƒ†–Š‡–‡•–”‡•—Ž–•ƒ”‡”‡ ‘”†‡†ǤŠ‹•‹ˆ‘”ƒ–‹‘‹•
”‡“—‹”‡†ˆ‘”–Š‡•Ǧ—‹Ž–‘ —‡–Ǥ
‡”‹ˆ›–Šƒ–‘Ž› ƒ’–‹˜‡ ‡–‡”’‹͹ͷŠ›’‡Ǧ  ‘‡ –‘”•ƒ”‡—•‡†‘–Š‡•‘Ž‹† ‘’’‡”
‡–‡” ‘†— –‘”͹ͷŠ ƒ„Ž‡Ǥ
‡”‹ˆ›–Šƒ––Š‡ ƒ„Ž‡‹•Žƒ„‡Ž‡†™‹–Šǣ
•
•
•
—•‹‘‹†‡„ƒ†ƒ‹ —„’‘”–—„‡”„‡‹‰—•‡†
‹†‡–‹ˆ‹‡”
ƒ””‹‡”ȋˆ‘”—Ž–‹’Ž‡‘’‡”ƒ–‘”•›•–‡•Ȍ
‘‡ ––Š‡ ƒ„Ž‡•–‘–Š‡ ˆ‡ƒŽ‡’‘”–‘–Š‡ƒ ‘”†‹‰–‘–Š‡Žƒ„‡Ž‘–Š‡ ƒ„Ž‡Ǥ
‘™‡”‹••—’’Ž‹‡†„›–Š‡ —•‹‘‹†‡„ƒ†ƒ‹ —„‘˜‡”–Š‡ ƒ„Ž‡ ‘†— –‘”•Ǥ’‘
’‘™‡”—’ǡ–Š‡•™‹ŽŽ„Ž‹ˆ‘”–™‘•‡ ‘†•ƒ•ƒ˜‹•—ƒŽ Š‡ –Šƒ––Š‡›ƒ”‡ˆ— –‹‘‹‰Ǥˆ–‡”
–Š‡–™‘Ǧ•‡ ‘†–‡•–ǣ
•
•
Š‡LINK•Š‘—Ž†„‡‰”‡‡‹†‹ ƒ–‹‰‹–‹•”‡ ‡‹˜‹‰’‘™‡”ƒ† ‘—‹ ƒ–‹‘•ˆ”‘
–Š‡ —•‹‘‹†‡„ƒ†ƒ‹ —„Ǥ
Š‡ALARM•Š‘—Ž†„‡”‡†—–‹Ž–Š‡ —•‹‘‹†‡„ƒ†ƒ‹ —„‹••—‡•–Š‡„ƒ†
‘ƒ†ǡ™‹–Š‹ƒ„‘—–ʹͲ•‡ ‘†•ǡ–Š‡‹–•Š‘—Ž†„‡‰”‡‡Ǥ
‡ ‘”†™Š‹ Š ƒ„Ž‡›‘—ƒ”‡ ‘‡ –‹‰–‘–Š‡ȋˆ”‘–Š‡Žƒ„‡Ž‘–Š‡ ƒ„Ž‡ȌǢ–Š‹•
‹ˆ‘”ƒ–‹‘‹•”‡“—‹”‡†ˆ‘”–Š‡•Ǧ—‹Ž–‘ —‡–Ǥ
‹‡Ǧ‘ˆˆ ƒ„Ž‡•‘”—•‡–Š‡‘’–‹‘ƒŽ ƒ„Ž‡ƒƒ‰‡”–‘ƒ˜‘‹††ƒƒ‰‹‰–Š‡ ‘‡ –‘”•„‡ ƒ—•‡‘ˆ
ƒ„Ž‡•–”ƒ‹Ǥ
Page 136
Š 2013 TE Connectivity Ltd
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Installing RAUs
TroubleshootingUsingRAULEDsDuringInstallation
Š‡LINK•Š‘—Ž†„‡‰”‡‡ƒ†”‡ƒ‹‰”‡‡ˆ‘”Ž‘‰‡”–ŠƒͻͲ•‡ ‘†•ǤŠ‡ALARM •ƒ”‡
”‡†™Š‡–Š‡•›•–‡„ƒ†Šƒ•‘–„‡‡’”‘‰”ƒ‡†Ǥ
Table89. TroubleshootingRAULEDsDuringInstallation
During
Installation
LED
State
Action
Impact
The RAU is connected to
the Fusion Wideband
Expansion Hub, which is
powered on
LINK
Off
Check CATV cable.
No power to the RAU.
ALARM
Off
LINK
Green
Red
LINK
Red from
green, after
cables are
connected for
60 seconds
• Check CATV cable
• Check the Main Hub LEDs—refer to
Step 2 in Table 87 on page 126.
• Use AdminBrowser to determine the
problem.
• Check CATV cable.
• Check the Hub LEDs.
• Use AdminBrowser to determine the
problem.
The RAU is off-line.
ALARM
ALARM
Red
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
No communications between
the RAU and the Hub.
Page 137
Š 2013 TE Connectivity Ltd.
Installing Fusion Wideband
CONFIGURINGTHEFUSIONWIDEBANDSYSTEM
‡ˆ‘”‡–Š‡•›•–‡ ƒ‘’‡”ƒ–‡’”‘’‡”Ž›ǡ—•‡†‹”‘™•‡”–‘’”‘‰”ƒ–Š‡ —•‹‘‹†‡„ƒ†
ƒ‹ —„™‹–Š–Š‡ˆ”‡“—‡ ›„ƒ†•–Šƒ–ƒ”‡–‘„‡†‹•–”‹„—–‡†ǤŠ‡ —„—•–„‡’”‘‰”ƒ‡†™‹–Š
–Š‡•ƒ‡ˆ”‡“—‡ ‹‡•ƒ•–Š‡—•‡†Ǥ
Š‡†‹”‘™•‡”•‘ˆ–™ƒ”‡ǡ†‡• ”‹„‡†‹–Š‡AdminBrowserUserManualȋǦ͸ʹͲ͸Ͳ͹ǦͲǦʹͲȌǡ
—•–„‡”—‹‰‘ƒȀŽƒ’–‘’Ǥ
NOTE:
The frequency bands should automatically be set on power up and this step should not be
required.
NOTE:
CrossoverEthernetcablewithmaleconnectorsrequired.
NOTE:
Thefollowingproceduresassumethatthesystemisnewfromthefactoryandthatithasnot
beenprogrammedwithbands.IfyouarereplacingcomponentsinapreͲinstalledsystemwith
eithernewunitsorunitsthatmayalreadybeprogrammed(forexample,reͲusingunitsfrom
anothersystem),referto“ReplacingFusionWidebandComponents”onpage175.
3 ConnectingthePCtotheMainHubtoRunAdminBrowser
‘‡ ––Š‡’‘™‡” ‘”†–‘–Š‡ —„Ǥ
CAUTION!
MakesuretheHubisgroundedthroughthegroundlugontheACpowerandtheframeground
lug as required. The warranty does not cover damage caused when an ungrounded Hub is
poweredon.
Ž—‰–Š‡’‘™‡” ‘”†‹–‘ƒ’‘™‡”‘—–Ž‡–Ǥ
‡”‹ˆ›–Šƒ–ƒŽŽ ƒ„Ž‡•ƒ”‡’”‘’‡”Ž› ‘‡ –‡†‘–Š‡ —„Ǥ
—”‘–Š‡’‘™‡”–‘–Š‡ —„Ǥ
ŽŽ•„Ž‹–Š”‘—‰Š–Š‡’‘™‡”—’•‡“—‡ ‡Ǥ–‡ƒ Š’‘”–™Š‡”‡ƒ‹•†‡–‡ –‡†
ȋ†”ƒ™‹‰ —””‡–Ȍǡ–Š‡’‘”–•Ž‹‰Š–•‰”‡‡ǤŠ‡ —•‹‘‹†‡„ƒ†STATUS‹•‘”ƒ‰‡
†—”‹‰•›•–‡„‘‘–ƒ†•Š‘—Ž†–—”‰”‡‡ƒˆ–‡”ƒ„‘—–ͻͲ•‡ ‘†•‹ˆ‹–ˆ‹†•‘ˆƒ—Ž–•ǤŠ‹•
•–ƒ–‡‹†‹ ƒ–‡•–Š‡„ƒ†ǯ•ƒ”‡‘–’”‘‰”ƒ‡†ƒ†’”‘˜‹†‡•ˆ‡‡†„ƒ ‘–Š‡•–ƒ–—•‘ˆ–Š‡
 ‘‡ –‹‘•Ǥ
Š‡•„Ž‹ˆ‘”ʹͲ•‡ ‘†•ƒ•ƒ˜‹•—ƒŽ Š‡ –Šƒ––Š‡›ƒ”‡ˆ— –‹‘‹‰Ǥ
‘‡ ––Š‡ ”‘••Ǧ‘˜‡”–Š‡”‡– ƒ„Ž‡–‘–Š‡ȀŽƒ’–‘’ƒ†–Š‡–‘–Š‡RJ-45 100-BASE-T ’‘”–
‘–Š‡ —„ǯ•ˆ”‘–’ƒ‡ŽǤ
Page 138
Š 2013 TE Connectivity Ltd
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Configuring the Fusion Wideband System
3 ProgrammingtheMainHubUsingAdminBrowser
‘‡ ––Š‡’”‘˜‹†‡†Ȁ  ”‘••‘˜‡” ƒ„Ž‡–‘–Š‡Žƒ’–‘’ƒ†–Š‡–‘–Š‡†‹ȀRJ-45
’‘”–‘–Š‡ —•‹‘‹†‡„ƒ†ƒ‹ —„ǯ•ˆ”‘–’ƒ‡ŽǤ
—”‘–Š‡Žƒ’–‘’ƒ†•–ƒ”––Š‡ —•‹‘‹†‡„ƒ†ƒ‹ —„Ǥ
‘‘‡‘ˆ–Š‡ˆ‘ŽŽ‘™‹‰ǣ
•
ForWindows2000:
a ‹‰Š–Ǧ Ž‹ My Network Placesƒ†
•‡Ž‡ –PropertiesǤ
‹‰ŠŽ‹‰Š–Internet Protocol (TCP/IP)
ƒ† Ž‹ PropertiesǤ• ”‡‡•‹‹Žƒ”
–‘–Š‡‘‡•Š‘™–‘–Š‡”‹‰Š–‘’‡•Ǥ
•
ForwindowsXP:
a Ž‹ Start>Settings>Network
Connections>LocalAreaConnectionǤŠ‡
™‹†‘™•Š‘™–‘–Š‡”‹‰Š–‘’‡•Ǥ
b –Š‡This connection uses the following
itemsǡ• ”‘ŽŽ†‘™–‘ƒ†•‡Ž‡ –Internet
Protocol (TCP/IP)ƒ† Ž‹ PropertiesǤ
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Page 139
Š 2013 TE Connectivity Ltd.
Installing Fusion Wideband
ƒ‡‘–‡‘ˆ–Š‡ —””‡– ƒ††”‡••ǡ—„‡–ƒ•ǡƒ†‡ˆƒ—Ž–‰ƒ–‡™ƒ›ǡ‹ˆ–Š‡›ƒ”‡ ‘ˆ‹‰—”‡†Ǥ
‘—™‹ŽŽ‡‡†–‘”‡Ǧ‡–‡”–Š‡ƒˆ–‡”›‘—Šƒ˜‡ ‘ˆ‹‰—”‡†–Š‡ —•‹‘‹†‡„ƒ†ƒ‹ —„Ǥ
‡Ž‡ –Use the following IP addressǤ
Šƒ‰‡–Š‡IP address–‘ͳͻʹǤͳ͸ͺǤͲǤͳͲͳ
Šƒ‰‡–Š‡Subnet mask–‘ʹͷͷǤʹͷͷǤʹͷͷǤͲ
Šƒ‰‡–Š‡Default gateway –‘ͳͻʹǤͳ͸ͺǤͲǤͳ
Ž‹ OK–™‹ ‡Ǥ‘—ƒ›„‡ƒ•‡†‹ˆ›‘—™ƒ––‘”‡„‘‘–›‘—” ‘’—–‡”Ǥ ˆ•‘ǡ Ž‹ YesǤ
UsingAdminBrowser
‘ƒ ‡•• —•‹‘‹†‡„ƒ†—•‹‰†‹”‘™•‡”ǡ—•‡–Š‡ˆ‘ŽŽ‘™‹‰•–‡’•ǣ
ƒ‡•—”‡–Š‡ƒ‹ —„–ƒ–—•‹•‰”‡‡Ǥ
›’‡–Š‡ˆ‘ŽŽ‘™‹‰‹–Š‡Ž‹‡ǣ
Https://192.168.0.100
Ž‹ GoǤ
Š‡†‹”‘™•‡”ƒ’’‡ƒ”•ǡŽ‘‰‹—•‹‰–Š‡†‡ˆƒ—Ž–—•‡” ǣoperatorǡƒ†–Š‡†‡ˆƒ—Ž–
’ƒ••™‘”†ǣpasswordǤ
Š‡†‹”‘™•‡”ƒ’’‡ƒ”•ǡŽ‘‰‹—•‹‰–Š‡†‡ˆƒ—Ž–—•‡” ƒ†–Š‡’ƒ••™‘”†ǡ™Š‹ Šƒ”‡
”‡•’‡ –‹˜‡Ž›ǣoperatorƒ†passwordǤ
Ž‹ SystemConfigurationƒ†–Š‡ Ž‹ SetDate/TimeǤ’ƒ‰‡•‹‹Žƒ”–‘‘‡•Š‘™„‡Ž‘™
‘’‡•Ǥ
–‡”–Š‡†‡•‹”‡†–‹‡ƒ††ƒ–‡‹–Š‡ˆ‘”ƒ–‹†‹ ƒ–‡†‘–Š‡’ƒ‰‡ƒ† Ž‹ SetDate/TimeǤ
’ƒ‰‡ƒ’’‡ƒ”•”‡“—‹”‹‰›‘—–‘”‡„‘‘––Š‡•›•–‡ˆ‘”–Š‡‡™†ƒ–‡ƒ†–‹‡–‘–ƒ‡‡ˆˆ‡ –Ǥ
Page 140
Š 2013 TE Connectivity Ltd
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Configuring the Fusion Wideband System
‡Ž‡ ––Š‡ —•‹‘ƒ‹ —„ƒ† Ž‹ Install/ConfigureSystemǤ• ”‡‡•‹‹Žƒ”–‘–Š‡‘‡
•Š‘™„‡Ž‘™‘’‡•Ǥ
ˆ†‡•‹”‡†ǡ–›’‡‹ƒLabelǤ
Š‡Žƒ„‡Ž‹•–Š‡•›•–‡ƒ‡†‹•’Žƒ›‡†‡š––‘–Š‡‹ ‘•ƒ†—•‡†‹‡••ƒ‰‡•Ǥ – ƒ„‡—’–‘
͵ʹ Šƒ”ƒ –‡”•Ž‘‰†‡’‡†‹‰—’‘–Š‡ˆ‹”™ƒ”‡˜‡”•‹‘Ǥ
10
Š‡†‡ˆƒ—Ž–•›•–‡Žƒ„‡Ž‹•Fusionǡƒ†™‹ŽŽ„‡—•‡†‹ˆ›‘—‡–‡”‘–Š‹‰Ǥ
•‡–Š‡‡š–•‡ –‹‘–‘• Š‡†—Ž‡ƒ›•–‡‡•–Ǥ
Š‹••‡ –‹‘ƒŽŽ‘™•›‘—–‘†‘–Š‡ˆ‘ŽŽ‘™‹‰ǣ
•
•
•
•
Ž‹ –Š‡ Š‡ „‘š–‘‡ƒ„Ž‡–Š‹•ˆ‡ƒ–—”‡Ǥ
Ž‹ –Š‡ Š‡ „‘š–‘ ƒ—•‡•›•–‡–‡•–‘’‘™‡”—’Ǥ
–‡”˜ƒŽ—‡•–‘• Š‡†—Ž‡–Š‡†ƒ–‡ƒ†–‹‡‘ˆ–Š‡‡š–•›•–‡–‡•–Ǥ
–‡”˜ƒŽ—‡•–‘•’‡ ‹ˆ›–Š‡”‡ —””‡ ‡‘ˆ–Š‡–‡•–„›†ƒ›‘”„›™‡‡Ǥ
 Š‡†—Ž‡›•–‡‡•–ƒŽŽ‘™•’‡”‹‘†‹ ǡƒ—–‘ƒ–‹ ‡š‡ —–‹‘‘ˆ–Š‡•›•–‡‡†Ǧ–‘Ǧ‡†–‡•–Ǥ —•–
Ž‹‡‡”ˆ‘”›•–‡‡•–ǡƒ Š‡†—Ž‡›•–‡‡•–•—•’‡†•‘”ƒŽ•‡”˜‹ ‡ˆ‘”–Š‡†—”ƒ–‹‘
‘ˆ–Š‡–‡•–Ǣ ƒŽŽ•ƒ”‡†”‘’’‡†ǡƒ†‘‡™ ƒŽŽ• ƒ„‡‡•–ƒ„Ž‹•Š‡††—”‹‰–Š‡–‡•–Ǥ‡•–
†—”ƒ–‹‘†‡’‡†•‘–Š‡ ‘ˆ‹‰—”ƒ–‹‘ȋ—„‡”‘ˆ•Ȍƒ†”‡“—‹”‡•‘‡‘”–™‘‹—–‡•–‘
‘’Ž‡–‡Ǥ
ˆ–‡” ‘’Ž‡–‹‘‘ˆ–Š‡•›•–‡–‡•–ǡ–Š‡• Š‡†—Ž‡†•›•–‡–‡•––‹‡‹•—’†ƒ–‡†–‘–Š‡‡š––‡•–
–‹‡ǡƒ†ƒ‡˜‡–Ž‘‰‡–”›‹•ƒ†‡Ǥ
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Page 141
Š 2013 TE Connectivity Ltd.
Installing Fusion Wideband
11
12
•‡–Š‡• ”‘ŽŽ„ƒ”‘–Š‡Ž‡ˆ–•‹†‡‘ˆ–Š‡’ƒ‰‡–‘• ”‘ŽŽ†‘™–‘˜‹‡™–Š‡”‡•–‘ˆ–Š‡’ƒ‰‡ƒ•
•Š‘™„‡Ž‘™Ǥ
–Š‡Bands’ƒ‡Žǡ†‘–Š‡ˆ‘ŽŽ‘™‹‰ǣ
•
•
•
•
13
‘—•Š‘—Ž†‘–Šƒ˜‡–‘•‡Ž‡ ––Š‡„ƒ†•ǤŠ‡•›•–‡•‡Žˆ ‘ˆ‹‰—”‡•–Š‡„ƒ†„›˜ƒŽ‹†ƒ–‹‰
–Šƒ–ƒŽŽ–Š‡• ‘‡ –‡†ƒ”‡–Š‡•ƒ‡–›’‡Ǥ
Š‡„‘–Š„ƒ†•ƒ”‡‘– ‘ˆ‹‰—”‡†ǡ—•‡–Š‡Shutdown Š‡ „‘šǤŠ‡•›•–‡™‹ŽŽ‹‰‘”‡
ƒ›ƒŽƒ”•‰‡‡”ƒ–‡†ˆ”‘–Š‡•Š—–†‘™„ƒ†•Ǥ
•‡–Š‡Uplinkƒ†Downlink‡—•–‘•‡Ž‡ ––Š‡‰ƒ‹ˆ‘”‡ƒ Š„ƒ†Ǥ‘— ƒ•‡–•›•–‡
‰ƒ‹™‹–Š‹–Š‡•’‡ ‹ˆ‹‡†”ƒ‰‡‹ͳ†‹ ”‡‡–•Ǥ
•‡–Š‡UplinkAutomaticLevelControl‡—–‘•‡Ž‡ –‡‹–Š‡”Single‘”Multipleȋ†‡ˆƒ—Ž–Ȍ
ˆ‘”‡ƒ Š„ƒ†‹–Š‡•›•–‡Ǥ
FORWiMAXINSTALLATIONSONLYǣ•‡–Š‡• ”‘ŽŽ„ƒ”‘–Š‡Ž‡ˆ–•‹†‡‘ˆ–Š‡’ƒ‰‡–‘• ”‘ŽŽ
†‘™–‘˜‹‡™–Š‡‡š–’ƒ”–‘ˆ–Š‡™‹†‘™••Š‘™„‡Ž‘™Ǥ
Page 142
Š 2013 TE Connectivity Ltd
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Configuring the Fusion Wideband System
–Š‡ƒ†ƒ”‡ƒǡ†‘–Š‡ˆ‘ŽŽ‘™‹‰ǣ
•
•
NOTE:
•
•
•
•
•
•
14
‡Ž‡ ––Š‡”‘–‘ ‘Ž‘†‡ǣŠ‹• ‘ˆ‹‰—”‡•–Š‡•›•–‡–‘•—’’‘”–‹”ƒ†‹‘•–Šƒ–ƒ”‡
‘‡‘ˆ–Š‡ˆ‘ŽŽ‘™‹‰ǣ
MIMOȋ—Ž–‹’Ž‡‹Ǧ—Ž–‹’Ž‡‘—–Ȍ
SISOȋ•‹‰Ž‡‹Ǧ•‹‰Ž‡‘—–ȌǤŠ‡†‡ˆƒ—Ž–‹•Dz dzǤ
‡Ž‡ ––Š‡‡–‡” ”‡“—‡ ›ƒ†ƒ†™‹†–Š—•‹‰–Š‡ƒ””‘™•‡š––‘–Š‡ˆ‹‡Ž†•ǤŠ‡ ‡–‡”
ˆ”‡“—‡ ›‹•–Š‡ˆ”‡“—‡ ›‘ˆ‹”ƒ†‹‘•„‡‹‰—•‡†ˆ‘”ƒ†ͳƒ†ƒ†ʹǤ
InMIMOmode,thefrequenciesarethesame.Thesystemcanbeconfiguredtosupport2ͲSISO
radios,oneperband,acrossany30MHzwithintheWiMAXband.
•‡–Š‡’—ŽŽǦ†‘™–‘•‡Ž‡ ––Š‡™‹– Š‹‰‘†‡ǤŠ‹•‹†‹ ƒ–‡•™Š‡–Š‡”‘”‘––Š‡
†‘™Ž‹Ǧ–‘Ǧ—’Ž‹ˆ”ƒ‡†—”ƒ–‹‘‹•‘™ǤŠ‡–™‘‘’–‹‘•ƒ”‡ƒ•ˆ‘ŽŽ‘™•ǣ
– StaticǦSelected:Š‹•‘†‡•’‡ ‹ˆ‹‡•–Š‡—„‡”‘ˆ•›„‘Ž•Ǥ•‡–Š‡’—ŽŽǦ†‘™–‘
•‡Ž‡ ––Š‡•›„‘Ž‹–Š‡†‘™Ž‹ƒ†—’Ž‹’‘”–‹‘•‘ˆ–Š‡ˆ”ƒ‡ǤȋŠ‡†‡ˆƒ—Ž–‹•
DzʹͻǡͳͺdzǤȌ –Š‹•‘†‡ǡ–Š‡•›•–‡ƒŽ™ƒ›••™‹– Š‡•ˆ”‘–Š‡†‘™Ž‹–‘–Š‡—’Ž‹
’ƒ–Šƒˆ–‡”–Š‡†‘™Ž‹’‘”–‹‘‘ˆ–Š‡ˆ”ƒ‡Šƒ•‡Žƒ’•‡†Ǥ
– StaticǦAuto:Š‹•‘†‡ ƒ—•‡•–Š‡•›•–‡–‘ƒ––‡’––‘†‡–‡”‹‡–Š‡ ‘””‡ –
•™‹– Š‹‰–‹‡ǡ–Š‡‡ˆ‘” ‡‹–ǤȋŠ‡†‡ˆƒ—Ž–‹•Dz–ƒ–‹ Ǧ—–‘dzȌ
‡Ž‡ ––Š‡ƒ†› Š”‘‹œƒ–‹‘‘†‡™‹–Š–Š‡’—ŽŽǦ†‘™ǤŠ‹•’ƒ”ƒ‡–‡” ƒ„‡
‘ˆ‹‰—”‡†–‘‘’‡”ƒ–‡ƒ•‘‡‘ˆ–Š‡ˆ‘ŽŽ‘™‹‰ǣ
– Synchronized:Š‹•‘†‡‹•ˆ‘” ƒ•‡•Ž‹‡ ǡ™Š‡”‡–Š‡–‹‹‰ˆ‘”„‘–Š„ƒ†•‹•
–Š‡•ƒ‡Ǥ –Š‹•‘†‡ǡ–Š‡•›•–‡ƒŽ™ƒ›••™‹– Š‡•„‡–™‡‡—’Ž‹ƒ††‘™Ž‹
•‹—Ž–ƒ‡‘—•Ž›ˆ‘”„‘–Š„ƒ†•Ǥ
– Unsynchronized: –Š‹•‘†‡ǡ–Š‡–™‘‹„ƒ†••™‹– Š‹†‡’‡†‡–Ž›ˆ”‘
‡ƒ Š‘–Š‡”ǤȋŠ‡†‡ˆƒ—Ž–‹•Dz•› Š”‘‹œ‡†dzȌ
Reference:‡Ž‡ –™Š‹ Š‹”ƒ†‹‘„ƒ†™‹ŽŽ„‡—•‡†ˆ‘”ˆ”ƒ‡”‡ˆ‡”‡ ‡Ǥ
Š‡ƒ›„ƒ†‹•‘– ‘ˆ‹‰—”‡†ǡ—•‡–Š‡Š—–†‘™ Š‡ „‘šǤŠ‡•›•–‡‹‰‘”‡•ƒ›
ƒŽƒ”•‰‡‡”ƒ–‡†ˆ”‘–Š‡•Š—–†‘™„ƒ†•Ǥ
•‡–Š‡’—ŽŽǦ†‘™–‘•’‡ ‹ˆ›–Š‡’Ž‹ƒ†‘™Ž‹‰ƒ‹ˆ‘”‡ƒ Š„ƒ†Ǥ‘— ƒ•‡–
•›•–‡‰ƒ‹™‹–Š‹–Š‡•’‡ ‹ˆ‹‡†”ƒ‰‡‹ͳ†‹ ”‡‡–•Ǥ
•‡–Š‡’—ŽŽǦ†‘™–‘•‡––Š‡’Ž‹—–‘ƒ–‹ ‡˜‡Ž‘–”‘Ž–‘‡‹–Š‡”Dz‹‰Ž‡dz‘”
Dz—Ž–‹’Ž‡dzˆ‘”‡ƒ Š„ƒ†‹–Š‡•›•–‡ǤȋŠ‡†‡ˆƒ—Ž–‹•Dz—Ž–‹’Ž‡ǤdzȌ
•‡–Š‡• ”‘ŽŽ„ƒ”‘–Š‡Ž‡ˆ–•‹†‡‘ˆ–Š‡™‹†‘™–‘• ”‘ŽŽ†‘™–‘˜‹‡™–Š‡”‡•–‘ˆ–Š‡™‹†‘™
ƒ••Š‘™„‡Ž‘™Ǥ
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Page 143
Š 2013 TE Connectivity Ltd.
Installing Fusion Wideband
15
–Š‡Input/OutputAlarms’ƒ‡Žǡ†‘–Š‡ˆ‘ŽŽ‘™‹‰ˆ‘”‡ƒ ŠŽƒ”‡•‡ǣ
•
•
•
16
ƒ„Ž‡‡ƒ ŠŽƒ”‡•‡„›—•‹‰–Š‡ Š‡ „‘šǤ
•‡–Š‡’—ŽŽǦ†‘™–‘•‡––Š‡‘”ƒŽ–ƒ–‡–‘Ž‘•‡†‘”’‡‡†ǤȋŠ‡†‡ˆƒ—Ž–‹•DzŽ‘•‡†Ǥdz
••‹‰ƒŽƒ„‡Ž–‘‡ƒ ŠƒŽƒ”•‡•‡Ǥ
Š‡›‘—Šƒ˜‡ ‘’Ž‡–‡†‹’—––‹‰–Š‡†‡•‹”‡†‹ˆ‘”ƒ–‹‘ǡ Ž‹ Install System –‘ ‘ˆ‹‰—”‡
–Š‡•›•–‡Ǥ
—”‹‰ ‘ˆ‹‰—”ƒ–‹‘ƒŽŽ†‹• ‘‡ –•–ƒ–—•‡•ƒ”‡ Ž‡ƒ”‡†ˆ‘”ƒ––ƒ Š‡†•Ǣ–Š‡ˆ”‡“—‡ ›
„ƒ†ǡ‰ƒ‹ǡƒ†•›•–‡Žƒ„‡Žƒ”‡•‡–ǢŽ‘‰•ƒ”‡ Ž‡ƒ”‡†Ǣ–Š‡•›•–‡–‡•–‹•’‡”ˆ‘”‡†Ǣƒ†ˆ‹ƒŽŽ›
–Š‡•›•–‡–”‡‡‹•”‡ˆ”‡•Š‡†ǤŠ‡‹ ‘••Š‘—Ž†„‡ǣ
Indicates that the band is correctly set on the Main Hub.
Indicates that the band is correctly set on the Expansion Hub.
Indicates that communications are OK.
17
ˆ–Š‡”‡ƒ”‡’”‘„Ž‡•ǡ–Š‡‹ ‘•™‹ŽŽ„‡†‹ˆˆ‡”‡–ƒ†ƒ‡••ƒ‰‡‹•†‹•’Žƒ›‡†‹–Š‡‡••ƒ‰‡•
’ƒ‡Ǥ
‘‡ ––Š‡ƒ‹ —„–‘–Š‡ •‘—” ‡ȋˆ‘”‡šƒ’Ž‡ǡ‘”ȌǤ
CAUTION!
Do not exceed the maximum input RF power (1Watt) to the Fusion Wideband Main Hub.
ExceedingthelimitcouldcausepermanentdamagetotheHub.
CAUTION!
OnlycarriersandtheirapprovedinstallersorTEͲauthorizedinstallersareallowedtoconnectto
theRFsource.SeriousdamagetotheequipmentcanoccurifitisoverͲdriven.
18
Š‡ —•‹‘‹†‡„ƒ†•›•–‡•Š‘—Ž†‘™„‡‘’‡”ƒ–‹‘ƒŽǤ•‹‰ƒ‘„‹Ž‡’Š‘‡ǡ™ƒŽ›‘—”
•‹–‡ƒ†–‡•––Š‡•‹‰ƒŽ•–”‡‰–ŠǤ
ƒ‡•—”‡–‘ Šƒ‰‡–Š‡Ȁ •‡––‹‰‹›‘—”Žƒ’–‘’„ƒ –‘–Š‡‹”‘”‹‰‹ƒŽ˜ƒŽ—‡•Ǥ
NOTE:
TEequipmentisdesignedtooperateinthelicensedfrequencybandsofmobileoperators.Inthe
USA,theEU,andmostcountriesthisequipmentmayonlybeusedbythelicensee,hisauthorized
agentsorthosewithwrittenauthorizationtodoso.Similarly,unauthorizeduseisillegal,and
subjectstheownertothecorrespondinglegalsanctionsofthenationaljurisdictioninvolved.
OwnershipofTEequipmentcarriesnoautomaticrightofuse.
Page 144
Š 2013 TE Connectivity Ltd
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Splicing Fiber Optic Cable
SPLICINGFIBEROPTICCABLE
Š‡ˆ‹„‡” ƒ„Ž‡—•–Šƒ˜‡Ȁ ‘‡ –‘”•ˆ‘”–Š‡‡–‹”‡”—Ǥ ˆ‹–†‘‡•‘–ǡ›‘— ƒ•’Ž‹ ‡ƒ
’‹‰–ƒ‹Žǡ™Š‹ ŠŠƒ•Ȁ ‘‡ –‘”•ǡ–‘–Š‡ˆ‹„‡” ƒ„Ž‡Ǥ
‘ˆˆ‡”•–™‘’‹‰–ƒ‹Ž•ǣ‘‡ˆ‘”•‹‰Ž‡Ǧ‘†‡ˆ‹„‡”ȋͶͲͳ͵Ǧ͵Ȍƒ†‘‡ˆ‘”—Ž–‹Ǧ‘†‡ˆ‹„‡”
ȋͶͲͳʹǦ͵ȌǤ
”‡ ‘‡†• —•‹‘‹†‡„ƒ†•’Ž‹ ‡•„‡ ƒ—•‡–Š‡›Šƒ˜‡–Š‡Ž‘™‡•–•’Ž‹ ‡Ž‘••ƒ†”‡–—”
Ž‘••Ǥ‡ Šƒ‹ ƒŽ•’Ž‹ ‡•Šƒ˜‡Š‹‰Š‡”Ž‘••‡•ƒ†Š‹‰Š‡”„ƒ ”‡ˆŽ‡ –‹‘–Šƒ —•‹‘‹†‡„ƒ†
•’Ž‹ ‡•ƒ†ƒ”‡‘–”‡ ‘‡†‡†Ǥ
•‹‰ƒ —•‹‘‹†‡„ƒ†•’Ž‹ ‡”‹˜‘Ž˜‡•ˆ—•‹‰–‘‰‡–Š‡”–™‘„—––‡†ƒ† Ž‡ƒ˜‡†‡†•‘ˆˆ‹„‡”Ǥ
Š‡ —•‹‘‹†‡„ƒ†•’Ž‹ ‡”ƒŽ‹‰•–Š‡ˆ‹„‡”•ƒ†ƒ‹–ƒ‹•ƒŽ‹‰‡–†—”‹‰–Š‡ —•‹‘
‹†‡„ƒ†’”‘ ‡••Ǥ —•‹‘‹†‡„ƒ†•’Ž‹ ‡•Šƒ˜‡˜‡”›Ž‘™Ž‘••ȋ–›’‹ ƒŽŽ›Ž‡••–ŠƒͲǤͲͷ†Ȍƒ†
˜‡”›Ž‘™„ƒ ”‡ˆŽ‡ –‹‘ȋ”‡–—”Ž‘••ȌǤ —•‹‘‹†‡„ƒ†•’Ž‹ ‡••Š‘—Ž†„‡‘”‰ƒ‹œ‡†‹ƒ•’Ž‹ ‡
–”ƒ›†‡•‹‰‡†–‘•–‘”‡ƒ†’”‘–‡ ––Š‡•’Ž‹ ‡•Ǥ
NOTE:
Thefollowingproceduresassumethatthesystemisnewfromthefactoryandthatithasnot
beenprogrammedwithbands.IfyouarereplacingcomponentsinapreͲinstalledsystemwith
eithernewunitsorunitsthatmayalreadybeprogrammed(forexample,reͲusingunitsfrom
anothersystem),referto“ReplacingFusionWidebandComponents”onpage175.
3 FusionWidebandSplicingofFiberandPigtail
OptionA:FusionWidebandSplicetheFiberͲOpticCabletotheSC/APCPigtail
10
11
ƒ‡•—”‡–Š‡ —•‹‘‹†‡„ƒ†•’Ž‹ ‡”‹••‡––‘–Š‡’”‘’‡”‘†‡ȋ–Šƒ–‹•ǡ•‹‰Ž‡Ǧ‘”
—Ž–‹Ǧ‘†‡ȌǤ
‡ —”‡„‘–Š–Š‡ˆ‹„‡” ƒ„Ž‡ƒ†–Š‡Ȁ’‹‰–ƒ‹Ž‹ƒ•’Ž‹ ‡–”ƒ›–Šƒ–‹•‹•–ƒŽŽ‡†‹‡†‹ƒ–‡Ž›
ƒ†Œƒ ‡––‘–Š‡ —„Ǥ
”‡’ƒ”‡–Š‡ˆ‹„‡”‡†„› —––‹‰„ƒ –Š‡’‘Ž›‡–Š›Ž‡‡Œƒ ‡–ǡ–Š‡‡˜Žƒ”‘”ˆ‹„‡”‰Žƒ•••–”‡‰–Š
‡„‡”•ǡ–Š‡‡š–”—†‡† ‘ƒ–‹‰ǡƒ†–Š‡„—ˆˆ‡” ‘ƒ–‹‰‹‘”†‡”–‘‡š’‘•‡–Š‡Dz„ƒ”‡ˆ‹„‡”dzȂ
Žƒ††‹‰’Ž—• ‘”‡Ǥ
•—”‡–Šƒ–•—ˆˆ‹ ‹‡–•Žƒ ‹•ƒ‹–ƒ‹‡†‹‘”†‡”–‘„‡ƒ„Ž‡–‘”‡ƒ Š–Š‡ —•‹‘‹†‡„ƒ†
•’Ž‹ ‡”Ǥ
Ž‡ƒ–Š‡— Žƒ†ˆ‹„‡” ‘”‡—•‹‰‹•‘’”‘’›ŽƒŽ ‘Š‘Žƒ†Ž‹–Ǧˆ”‡‡™‹’‡•Ǥ
Ž‡ƒ˜‡–Š‡— Žƒ†ˆ‹„‡”–‘–Š‡Ž‡‰–Š’”‡• ”‹„‡†„›–Š‡ —•‹‘‹†‡„ƒ†•’Ž‹ ‡”ǯ•
•’‡ ‹ˆ‹ ƒ–‹‘•Š‡‡–•Ǥ
‡’‡ƒ––‡’Ͷ–Š”‘—‰Š–‡’͸ˆ‘”–Š‡Ȁ’‹‰–ƒ‹ŽǤ
ƒ••–Š‡•’Ž‹ ‡•Ž‡‡˜‡‘–‘–Š‡ˆ‹„‡”•–”ƒ†Ǥ
‘•‹–‹‘„‘–Šˆ‹„‡”‡†•‹–Š‡ —•‹‘‹†‡„ƒ†•’Ž‹ ‡”ƒ† ‘’Ž‡–‡•’Ž‹ ‡‹ƒ ‘”†ƒ ‡
™‹–Š–Š‡ —•‹‘‹†‡„ƒ†•’Ž‹ ‡”ǯ•‘’‡”ƒ–‹‘‹•–”— –‹‘•Ǥ
•—”‡–Šƒ––Š‡‡•–‹ƒ–‡†Ž‘••ˆ‘”–Š‡•’Ž‹ ‡ƒ•‡ƒ•—”‡†„›–Š‡ —•‹‘‹†‡„ƒ†•’Ž‹ ‡”‹•
ͲǤͳͲ†‘”„‡––‡”Ǥ
Ž‹†‡–Š‡ —•‹‘‹†‡„ƒ†•’Ž‹ ‹‰•Ž‡‡˜‡‘˜‡”–Š‡’‘‹–‘ˆ–Š‡ —•‹‘‹†‡„ƒ†•’Ž‹ ‡Ǥ
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Page 145
Š 2013 TE Connectivity Ltd.
Installing Fusion Wideband
12
13
14
15
Žƒ ‡–Š‡•Ž‡‡˜‡ƒ†ˆ—•‡†ˆ‹„‡”‹–‘–Š‡ —•‹‘‹†‡„ƒ†•’Ž‹ ‡”ǯ•Š‡ƒ–‡”Ǥ
ŽŽ‘™–‹‡ˆ‘”–Š‡•’Ž‹ ‡•Ž‡‡˜‡–‘ —”‡Ǥ
‡–—”ˆ‹„‡”•’Ž‹ ‡–‘–Š‡•’Ž‹ ‡–”ƒ›ǡ•–‘”‡–Š‡•Ž‡‡˜‡‹ƒ•’Ž‹ ‡Š‘Ž†‡”™‹–Š‹–Š‡–”ƒ›ǡƒ†
•–‘”‡‡š ‡•• ƒ„Ž‡Ž‡‰–Š‹ƒ ‘”†ƒ ‡™‹–Š–Š‡–”ƒ›ƒ—ˆƒ –—”‡ǯ•†‹”‡ –‹‘•Ǥ
ˆ–‡”•— ‡••ˆ—ŽŽ›–‡•–‹‰–Š‡ˆ‹„‡”ǡ’Ž—‰–Š‡Ȁ’‹‰–ƒ‹Ž‹–‘–Š‡’”‘’‡”‘’–‹ ƒŽ’‘”–‘–Š‡
—„Ǥ
OptionB:FusionWidebandSplicetheFiberͲOpticCabletotheSC/APCPigtail
10
11
12
13
14
15
16
ƒ‡•—”‡–Š‡ —•‹‘‹†‡„ƒ†•’Ž‹ ‡”‹••‡––‘–Š‡’”‘’‡”‘†‡ȋ–Šƒ–‹•ǡ•‹‰Ž‡Ǧ‘”
—Ž–‹Ǧ‘†‡ȌǤ
‡ —”‡„‘–Š–Š‡ˆ‹„‡” ƒ„Ž‡ƒ†–Š‡Ȁ’‹‰–ƒ‹Ž‹ƒ•’Ž‹ ‡–”ƒ›’‘”–‹‘‘ˆƒˆ‹„‡”
†‹•–”‹„—–‹‘’ƒ‡ŽǤ
”‡’ƒ”‡–Š‡ˆ‹„‡”‡†„› —––‹‰„ƒ –Š‡’‘Ž›‡–Š›Ž‡‡Œƒ ‡–ǡ–Š‡‡˜Žƒ”‘”ˆ‹„‡”‰Žƒ•••–”‡‰–Š
‡„‡”•ǡ–Š‡‡š–”—†‡† ‘ƒ–‹‰ǡƒ†–Š‡„—ˆˆ‡” ‘ƒ–‹‰‹‘”†‡”–‘‡š’‘•‡–Š‡Dz„ƒ”‡ˆ‹„‡”dzȂ
Žƒ††‹‰’Ž—• ‘”‡Ǥ
•—”‡–Šƒ–•—ˆˆ‹ ‹‡–•Žƒ ‹•ƒ‹–ƒ‹‡†‹‘”†‡”–‘„‡ƒ„Ž‡–‘”‡ƒ Š–Š‡ —•‹‘‹†‡„ƒ†
•’Ž‹ ‡”Ǥ
Ž‡ƒ–Š‡— Žƒ†ˆ‹„‡” ‘”‡—•‹‰‹•‘’”‘’›ŽƒŽ ‘Š‘Žƒ†Ž‹–Ǧˆ”‡‡™‹’‡•Ǥ
Ž‡ƒ˜‡–Š‡— Žƒ†ˆ‹„‡”–‘–Š‡Ž‡‰–Š’”‡• ”‹„‡†„›–Š‡ —•‹‘‹†‡„ƒ†•’Ž‹ ‡”ǯ•
•’‡ ‹ˆ‹ ƒ–‹‘•Š‡‡–•Ǥ
‡’‡ƒ––‡’͵–Š”‘—‰Š–‡’͸ˆ‘”–Š‡Ȁ’‹‰–ƒ‹ŽǤ
ƒ••–Š‡•’Ž‹ ‡•Ž‡‡˜‡‘–‘–Š‡ˆ‹„‡”•–”ƒ†Ǥ
‘•‹–‹‘„‘–Šˆ‹„‡”‡†•‹–Š‡ —•‹‘‹†‡„ƒ†•’Ž‹ ‡”ƒ† ‘’Ž‡–‡•’Ž‹ ‡‹ƒ ‘”†ƒ ‡
™‹–Š–Š‡ —•‹‘‹†‡„ƒ†•’Ž‹ ‡”ǯ•‘’‡”ƒ–‹‘‹•–”— –‹‘•Ǥ
•—”‡–Šƒ––Š‡‡•–‹ƒ–‡†Ž‘••ˆ‘”–Š‡•’Ž‹ ‡ƒ•‡ƒ•—”‡†„›–Š‡ —•‹‘‹†‡„ƒ†•’Ž‹ ‡”‹•
ͲǤͳͲ†‘”„‡––‡”Ǥ
Ž‹†‡–Š‡ —•‹‘‹†‡„ƒ†•’Ž‹ ‹‰•Ž‡‡˜‡‘˜‡”–Š‡’‘‹–‘ˆ–Š‡ —•‹‘‹†‡„ƒ†•’Ž‹ ‡Ǥ
Žƒ ‡–Š‡•Ž‡‡˜‡ƒ†ˆ—•‡†ˆ‹„‡”‹–‘–Š‡ —•‹‘‹†‡„ƒ†•’Ž‹ ‡”ǯ•Š‡ƒ–‡”Ǥ
ŽŽ‘™–‹‡ˆ‘”–Š‡•’Ž‹ ‡•Ž‡‡˜‡–‘ —”‡Ǥ
‡–—”ˆ‹„‡”•’Ž‹ ‡–‘–Š‡•’Ž‹ ‡–”ƒ›ǡ•–‘”‡–Š‡•Ž‡‡˜‡‹ƒ•’Ž‹ ‡Š‘Ž†‡”™‹–Š‹–Š‡–”ƒ›ǡƒ†
•–‘”‡‡š ‡•• ƒ„Ž‡Ž‡‰–Š‹ƒ ‘”†ƒ ‡™‹–Š–Š‡–”ƒ›ƒ—ˆƒ –—”‡ǯ•†‹”‡ –‹‘•Ǥ
ˆ–‡”•— ‡••ˆ—ŽŽ›–‡•–‹‰–Š‡ˆ‹„‡” ƒ„Ž‡ǡ’Ž—‰–Š‡Ȁ’‹‰–ƒ‹Ž‹–‘–Š‡„ƒ •‹†‡‘ˆ–Š‡
Ȁ„—ŽŠ‡ƒ†‹–Š‡ ‹„‡”‹•–”‹„—–‹‘ƒ‡ŽǤ
•–ƒŽŽƒȀ’ƒ– Š ‘”†„‡–™‡‡–Š‡ˆ”‘–•‹†‡‘ˆ–Š‡Ȁ„—ŽŠ‡ƒ†ƒ†–Š‡’”‘’‡”
‘’–‹ ƒŽ’‘”–‘–Š‡ —„Ǥ
NOTE:
For information on troubleshooting, see “Maintenance, Troubleshooting, and Technical
Assistance”onpage181.
Page 146
Š 2013 TE Connectivity Ltd
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Interfacing the Fusion Wideband Main Hub to an RF Source
INTERFACINGTHEFUSIONWIDEBANDMAINHUBTOANRFSOURCE
CAUTION!
OnlyTEpersonnelorTEͲauthorizedinstallationpersonnelshouldconnecttheFusionWideband
MainHubtoitsBandassociatedbasestationorrepeater.Exceedingthemaximuminputpower
couldcausefailureoftheFusionWidebandMainHub(referto“RemoteAccessUnitConnectors”
onpage57formaximumpowerspecifications).Ifthemaximumcompositepoweristoohigh,
attenuationisrequired.
NOTE:
Thefollowingproceduresassumethatthesystemisinstalledandhasbeenprogrammedwith
bands.
ConnectingaSingleFusionWidebandMainHubtoanRFSource
Š‡ —•‹‘‹†‡„ƒ†•›•–‡•—’’‘”–•–Š”‡‡ •‘—” ‡•ǡ‘‡ˆ‘”ƒ†ͳǡƒ†ʹǡƒ†ƒ†͵ǤŠ‹•
•‡ –‹‘‡š’Žƒ‹•Š‘™‡ƒ Šƒ† ƒ„‡ ‘‡ –‡†–‘‹–•ƒ••‘ ‹ƒ–‡† •‘—” ‡Ǥ
3 ConnectingaFusionWidebandMainHubtoanInͲBuildingBTS
CAUTION!
OnlyTEpersonnelorTEͲauthorizedinstallationpersonnelshouldconnecttheFusionWideband
MainHubtoabasestationorrepeater.Exceedingthemaximuminputpowercouldcausefailure
oftheFusionWidebandMainHub(referto“RemoteAccessUnitConnectors”onpage57for
maximumpowerspecifications).Ifthemaximumcompositepoweristoohigh,attenuationis
required.
CAUTION!
The UPLINKand DOWNLINK portscannothandleaDCpowerfeedfromthebasestation.IfDC
powerispresent,aDCblockmustbeusedorthehubmaybedamaged.
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Page 147
Š 2013 TE Connectivity Ltd.
Installing Fusion Wideband
ConnectingaSimplexBaseStationtoaFusionWidebandMainHubRFBand
‘‡ –ƒǦƒŽ‡–‘ǦƒŽ‡ ‘ƒš‹ƒŽ ƒ„Ž‡–‘–Š‡–”ƒ•‹–•‹’Ž‡š ‘‡ –‘”‘–Š‡„ƒ•‡
•–ƒ–‹‘Ǥ
‘‡ ––Š‡‘–Š‡”‡†‘ˆ–Š‡ǦƒŽ‡–‘ǦƒŽ‡ ‘ƒš‹ƒŽ ƒ„Ž‡–‘–Š‡DOWNLINK ‘‡ –‘”‘–Š‡
—„ˆ‘”–Š‡ ‘””‡•’‘†‹‰ƒ†ͳǡƒ†ʹǡ‘”ƒ†͵Ǥ
‘‡ –ƒǦƒŽ‡–‘ǦƒŽ‡ ‘ƒš‹ƒŽ ƒ„Ž‡–‘–Š‡”‡ ‡‹˜‡•‹’Ž‡š ‘‡ –‘”‘–Š‡„ƒ•‡
•–ƒ–‹‘Ǥ
‘‡ ––Š‡‘–Š‡”‡†‘ˆ–Š‡ǦƒŽ‡–‘ǦƒŽ‡ ‘ƒš‹ƒŽ ƒ„Ž‡–‘–Š‡UPLINK ‘‡ –‘”‘–Š‡
—„ˆ‘”–Š‡ ‘””‡•’‘†‹‰ƒ†ͳǡƒ†ʹǡ‘”ƒ†͵Ǥ
Band 1
Band 2
UL1
UL2
Band 3
UL3
AC Power
Alarms
DL1
DL2
DL3
N-male to N-male
coaxial cable
Insert attenuator
(if needed)
Simplex
Base Station
Band 3
NOTE: This applies to Band 1, Band 2, and Band 3.
T1/E1 to
Mobile
Switching
Center
Figure40.Simplex Base Station to a Fusion Wideband Main Hub
Page 148
Š 2013 TE Connectivity Ltd
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Interfacing the Fusion Wideband Main Hub to an RF Source
ConnectingaDuplexBaseStationtoaFusionWidebandMainHub
NOTE:
Whenconnectingtoaduplexbasestation,useacirculatororduplexerbetweenitandtheFusion
WidebandMainHub.
NOTE:
YoucaninsertattenuatorsbetweenthecirculatororduplexerandHubasneeded.
‘‡ –ƒǦƒŽ‡–‘ǦƒŽ‡ ‘ƒš‹ƒŽ ƒ„Ž‡–‘–Š‡†—’Ž‡š ‘‡ –‘”‘–Š‡„ƒ•‡•–ƒ–‹‘Ǥ
‘‡ ––Š‡‘–Š‡”ǦƒŽ‡ ‘‡ –‘”‘”†—’Ž‡š‡”–‘ƒ ‹” —Žƒ–‘”Ǥ
‘‡ –ƒǦƒŽ‡–‘ǦƒŽ‡ ‘ƒš‹ƒŽ ƒ„Ž‡–‘–Š‡DOWNLINK ‘‡ –‘”‘–Š‡ —„ˆ‘”ƒ†ͳǡ
ƒ†ʹǡƒ†ƒ†͵Ǥ
‘‡ ––Š‡‘–Š‡”‡†‘ˆ–Š‡ǦƒŽ‡ ‘ƒš‹ƒŽ ƒ„Ž‡–‘–Š‡–”ƒ•‹– ‘‡ –‘”‘–Š‡ ‹” —Žƒ–‘”Ǥ
‘‡ –ƒǦƒŽ‡–‘ǦƒŽ‡ ‘ƒš‹ƒŽ ƒ„Ž‡–‘–Š‡UPLINK ‘‡ –‘”‘–Š‡ —„ˆ‘”ƒ†ͳǡ
ƒ†ʹǡƒ†ƒ†͵Ǥ
‘‡ ––Š‡‘–Š‡”‡†‘ˆ–Š‡ǦƒŽ‡ ‘ƒš‹ƒŽ ƒ„Ž‡–‘–Š‡”‡ ‡‹˜‡ ‘‡ –‘” ‘–Š‡ ‹” —Žƒ–‘”Ǥ
Band 1
Band 2
UL1
UL2
Band 3
UL3
AC Power
Alarms
DL1
DL2
DL3
N-male to N-male
coaxial cable
Insert attenuator
(if needed)
Circulator
N-male to N-male
coaxial cable
Duplex
Base Station
T1/E1 to
Mobile
Switching
Center
NOTE: This applies to Band 1, Band 2, and Band 3.
Figure41.Duplex Base Station to a Fusion Wideband Main Hub
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Page 149
Š 2013 TE Connectivity Ltd.
Installing Fusion Wideband
3 ConnectingaFusionWidebandMainHubRFBandtoMultipleBTSs
CAUTION!
OnlyTEpersonnelorTEͲauthorizedinstallationpersonnelshouldconnecttheFusionWideband
MainHubtoabasestationorrepeater.Exceedingthemaximuminputpowercouldcausefailure
oftheFusionWidebandMainHub(referto“RemoteAccessUnitConnectors”onpage57for
maximumpowerspecifications).Ifthemaximumcompositepoweristoohigh,attenuationis
required.
‘— ƒ—•‡’‘™‡” ‘„‹‡”Ȁ•’Ž‹––‡”•–‘ ‘‡ –ƒ —•‹‘‹†‡„ƒ†ƒ‹ —„ ƒ†–‘
—Ž–‹’Ž‡„ƒ•‡•–ƒ–‹‘•ǡƒ••Š‘™‹ ‹‰—”‡Ͷʹ‘’ƒ‰‡ͳͷͲǤ
Band 1
Band 2
UL1
UL2
Band 3
UL3
AC Power
Alarms
DL1
DL2
DL3
N-male to N-male
coaxial-jumper cables
between Combiner/Splitter and
Fusion Main Hub’s Uplink Port
for each on Band 1, Band 2, or Band 3
2 x 1 Power
Combiner/Splitter
N-male to N-male
coaxial-jumper cables
between Combiner/Splitter and
Fusion Main Hub’s Downlink Port
for either Band 1, Band 2, or Band 3
2 x 1 Power
Combiner/Splitter
Insert attenuators
(if needed)
UL
DL
BTS 1
UL
DL
BTS 2
Figure42.Connecting a Fusion Wideband Main Hub to Multiple Base Stations
Page 150
Š 2013 TE Connectivity Ltd
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Interfacing the Fusion Wideband Main Hub to an RF Source
3 ConnectingaFusionWidebandMainHubtoaRoofͲTopAntenna
CAUTION!
10
TE recommends that you use a lightning arrestor or surge protector in a roofͲtop antenna
configuration.InsertthelightningarrestororsurgeprotectorbetweentheroofͲtopantennaand
therepeaterconnectedtotheFusionWidebandMainHubRFBand.
‘‡ –ƒǦƒŽ‡–‘ǦƒŽ‡ ‘ƒš‹ƒŽ ƒ„Ž‡–‘–Š‡”‘‘ˆǦ–‘’ƒ–‡ƒǤ
‘‡ ––Š‡‘–Š‡”‡†‘ˆ–Š‡ǦƒŽ‡–‘ǦƒŽ‡ ‘ƒš‹ƒŽ ƒ„Ž‡–‘–Š‡‰”‘—†‡†•—”‰‡
•—’’”‡••‘”Ǥ
‘‡ –ƒǦƒŽ‡–‘ǦƒŽ‡ ‘ƒš‹ƒŽ ƒ„Ž‡–‘–Š‡‰”‘—†‡†•—”‰‡•—’’”‡••‘”Ǥ
‘‡ ––Š‡‘–Š‡”‡†‘ˆ–Š‡ǦƒŽ‡–‘ǦƒŽ‡ ‘ƒš‹ƒŽ ƒ„Ž‡–‘–Š‡”‡’‡ƒ–‡”Ǥ
‘‡ –ƒǦƒŽ‡–‘ǦƒŽ‡ ‘ƒš‹ƒŽ ƒ„Ž‡–‘–Š‡”‡’‡ƒ–‡”Ǥ
‘‡ ––Š‡‘–Š‡”‡†‘ˆ–Š‡ǦƒŽ‡–‘ǦƒŽ‡ ‘ƒš‹ƒŽ ƒ„Ž‡–‘–Š‡ ‹” —Žƒ–‘”1 ‘‡ –‘”Ǥ
‘‡ –ƒǦƒŽ‡–‘ǦƒŽ‡ ‘ƒš‹ƒŽ ƒ„Ž‡–‘–Š‡ ‹” —Žƒ–‘”2 ‘‡ –‘”Ǥ
‘‡ ––Š‡‘–Š‡”‡†‘ˆ–Š‡ǦƒŽ‡–‘ǦƒŽ‡ ‘ƒš‹ƒŽ ƒ„Ž‡–‘–Š‡DOWNLINK ‘‡ –‘”‘–Š‡
—„ˆ‘”‡‹–Š‡”ƒ†ͳǡƒ†ʹǡ‘”ƒ†͵Ǥȋ––‡—ƒ–‹‘ƒ›„‡”‡“—‹”‡†–‘ƒ Š‹‡˜‡–Š‡†‡•‹”‡†
 ‘—–’—–ƒ––Š‡ǤȌ
‘‡ –ƒǦƒŽ‡–‘ǦƒŽ‡ ‘ƒš‹ƒŽ ƒ„Ž‡–‘–Š‡ ‹” —Žƒ–‘”3 ‘‡ –‘”Ǥ
‘‡ ––Š‡‘–Š‡”‡†‘ˆ–Š‡ǦƒŽ‡–‘ǦƒŽ‡ ‘ƒš‹ƒŽ ƒ„Ž‡–‘–Š‡UPLINK ‘‡ –‘”‘–Š‡
—„ˆ‘”‡‹–Š‡”ƒ†ͳǡƒ†ʹǡ‘”ƒ†͵Ǥ
Band 1
UL1
Band 2
UL2
Band 3
UL3
AC Power
Alarms
DL1
DL2
DL3
Rooftop
Antenna
N-male to N-male
coaxial cable
Grounded
Surge Suppressor
N-male to N-male
coaxial cable
NOTE: This applies to Band 1, Band 2, and Band 3.
Circulator
Rooftop
Antenna
Attenuator
(optional)
Figure43.Connecting a Fusion Wideband Main Hub to a Roof-top Antenna
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Page 151
Š 2013 TE Connectivity Ltd.
Installing Fusion Wideband
3 ConnectingaFusionWidebandMainHubtoFlexwaveFocus
‡ˆ‡”–‘–Š‡ Ž‡šƒ˜‡ ‘ —•ƒ—ƒŽˆ‘”‹ˆ‘”ƒ–‹‘Ǥ
ConnectingMultipleFusionWidebandMainHubstoanRFSource
‘— ƒ—•‡’‘™‡” ‘„‹‡”Ȁ•’Ž‹––‡”•ƒ••’Ž‹––‡”•–‘ ‘‡ –—Ž–‹’Ž‡ —•‹‘‹†‡„ƒ†ƒ‹
—„•‹‘”†‡”–‘‹ ”‡ƒ•‡–Š‡–‘–ƒŽ—„‡”‘ˆ•‹ƒ•›•–‡Ǥ‘— ƒƒŽ•‘—•‡’‘™‡”
‘„‹‡”Ȁ•’Ž‹––‡”•–‘ ‘„‹‡„ƒ•‡•–ƒ–‹‘ Šƒ‡Ž•‹‘”†‡”–‘‹ ”‡ƒ•‡–Š‡—„‡”‘ˆ 
ƒ””‹‡”•–Š‡•›•–‡–”ƒ•’‘”–•Ǥ
3 ConnectingMultipleFusionWidebandMainHubstoaSimplexRepeaterorBTS
CAUTION!
OnlyTEpersonnelorTEͲauthorizedinstallationpersonnelshouldconnecttheFusionWideband
MainHubtoabasestationorrepeater.Exceedingthemaximuminputpowercouldcausefailure
oftheFusionWidebandMainHub(referto“RemoteAccessUnitConnectors”onpage57for
maximumpowerspecifications).Ifthemaximumcompositepoweristoohigh,attenuationis
required.
ƒ‡•—”‡›‘—Šƒ˜‡–Š‡ˆ‘ŽŽ‘™‹‰ ‘’‘‡–•ǣ
Quantity
Item
hybrid power combiner/splitters—one for uplink and one for downlink (2x1 for two Fusion Wideband Main
Hubs, 3x1 for three, 4x1 for four, and so on)
N-male to N-male coaxial jumper cable between each power combiner/splitter and the base station
N-male to N-male coaxial jumper cables between each power combiner/splitter and each Fusion Wideband
Main Hub RF Band (either Band 1 or Band 2)
‘‡ ––Š‡’‘™‡” ‘„‹‡”Ȁ•’Ž‹––‡”•–‘–Š‡”‡’‡ƒ–‡”‘”„ƒ•‡•–ƒ–‹‘—•‹‰ǦƒŽ‡–‘ǦƒŽ‡
‘ƒš‹ƒŽŒ—’‡” ƒ„Ž‡•ǣ
”‘–Š‡ˆ‹”•–’‘™‡” ‘„‹‡”Ȁ•’Ž‹––‡”–‘–Š‡”‡’‡ƒ–‡”‘”„ƒ•‡•–ƒ–‹‘UPLINK
”‘–Š‡•‡ ‘†’‘™‡” ‘„‹‡”Ȁ•’Ž‹––‡”–‘–Š‡”‡’‡ƒ–‡”‘”„ƒ•‡•–ƒ–‹‘DOWNLINK
‘‡ ––Š‡’‘™‡” ‘„‹‡”Ȁ•’Ž‹––‡”•–‘–Š‡ —„•ǣ
”‘–Š‡ˆ‹”•– —„ǯ•UPLINK ’‘”–ȋƒ†ͳǡƒ†ʹǡ‘”ƒ†͵Ȍ–‘–Š‡ˆ‹”•–’‘™‡”
‘„‹‡”Ȁ•’Ž‹––‡”
”‘–Š‡ˆ‹”•– —„ǯ•DOWNLINK ’‘”–ȋƒ†ͳǡƒ†ʹǡ‘”ƒ†͵Ȍ–‘–Š‡•‡ ‘†’‘™‡”
‘„‹‡”Ȁ•’Ž‹––‡”
”‘–Š‡•‡ ‘† —„ǯ•UPLINK ’‘”–ȋƒ†ͳǡƒ†ʹǡ‘”ƒ†͵Ȍ–‘–Š‡ˆ‹”•–’‘™‡”
‘„‹‡”Ȁ•’Ž‹––‡”
”‘–Š‡•‡ ‘† —„ǯ•DOWNLINK ’‘”–ȋƒ†ͳǡƒ†ʹǡ‘”ƒ†͵Ȍ–‘–Š‡•‡ ‘†’‘™‡”
‘„‹‡”Ȁ•’Ž‹––‡”
NOTE:
ConnectionsshouldnotcrossBands.Forexample,allBand1connectionsshouldbemadetothe
samehybridpowercombiner/splitterconnectedtotherepeaterBTSthatmatchestheBand1
frequency.
Page 152
Š 2013 TE Connectivity Ltd
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Interfacing the Fusion Wideband Main Hub to an RF Source
Š‡  —„•Ȅˆ–‡” ‘‡ –‹‰ƒ†’‘™‡”‹‰‘–Š‡ —„ǡ Š‡ ƒŽŽ•–‘‡•—”‡–Šƒ–
–Š‡•›•–‡‹•‘’‡”ƒ–‹‰’”‘’‡”Ž›Ǥ
ƒ‡•—”‡–Š‡ —„‹•‰”‘—†‡†ǤThewarrantydoesnotcoverdamagecausedwhenan
ungroundedHubispoweredon.
NOTE:
Usea50ohmterminatoronanyunusedpowercombiner/splitterports.
‹‰—”‡ͶͶ•Š‘™•Š‘™–‘ ‘‡ ––™‘ƒ‹ —„•–‘ƒ•‹’Ž‡š”‡’‡ƒ–‡”‘”„ƒ•‡•–ƒ–‹‘Ǥ‘‡ –‹‰
–™‘ —„•‹ ”‡ƒ•‡•–Š‡–‘–ƒŽ—„‡”‘ˆ•—’’‘”–ƒ„Ž‡•ˆ”‘ͺ–‘ͳ͸Ǥ
Band 1
UL1
Band 2
UL2
Band 3
UL3
AC Power
Alarms
DL1
DL2
DL3
Band 1
UL1
N-male to N-male
coaxial-jumper cables
between Combiner/Splitter
and Fusion Main Hub’s
Uplink Port for either Band 1,
Band 2, or Band 3
Band 2
Band 3
UL2
UL3
AC Power
Alarms
DL1
DL2
DL3
N-male to N-male
coaxial-jumper cables
between Combiner/Splitter and
Fusion Main Hub’s Downlink Port
for either Band 1, Band 2, or Band 3
2 x 1 Power
Combiner/Splitter
N-male to N-male
coaxial-jumper cable
to Repeater or
Base Station
2 x 1 Power
Combiner/Splitter
N-male to N-male
coaxial-jumper cable
to Repeater or
Base Station
Figure44.Connecting Two Fusion Wideband Main Hub’s RF Band Ports to a Simplex Repeater or Base Station
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Page 153
Š 2013 TE Connectivity Ltd.
Installing Fusion Wideband
3 ConnectingMultipleFusionWidebandMainHubstoaDuplexRepeaterorBTS
CAUTION!
OnlyTEpersonnelorTEͲauthorizedinstallationpersonnelshouldconnecttheFusionWideband
MainHubtoabasestationorrepeater.Exceedingthemaximuminputpowercouldcausefailure
oftheFusionWidebandMainHub(referto“RemoteAccessUnitConnectors”onpage57for
maximumpowerspecifications).Ifthemaximumcompositepoweristoohigh,attenuationis
required.
ƒ‡•—”‡›‘—Šƒ˜‡–Š‡ˆ‘ŽŽ‘™‹‰ ‘’‘‡–•ǣ
Quantity
Item
hybrid power combiner/splitters—one for uplink and one for downlink (2x1 for two Fusion Wideband Main
Hubs, 3x1 for three, 4x1 for four, and so on)
N-male to N-male coaxial jumper cables to connect each Fusion Wideband Main Hub’s RF Band to the power
combiner/splitters
circulator
N-male to N-male coaxial jumper cable between each circulator and the repeater or base station
N-male to N-male coaxial jumper cable between each circulator and power combiner/splitter
‘‡ ––Š‡ ‹” —Žƒ–‘”–‘–Š‡”‡’‡ƒ–‡”‘”„ƒ•‡•–ƒ–‹‘—•‹‰‘‡ǦƒŽ‡–‘ǦƒŽ‡ ‘ƒš‹ƒŽ
Œ—’‡” ƒ„Ž‡Ǥ
‘‡ –‡ƒ Š’‘™‡” ‘„‹‡”Ȁ•’Ž‹––‡”–‘–Š‡ ‹” —Žƒ–‘”—•‹‰‘‡ǦƒŽ‡–‘ǦƒŽ‡ ‘ƒš‹ƒŽ
Œ—’‡” ƒ„Ž‡’‡” ‘„‹‡”Ȁ•’Ž‹––‡”Ǥ
‘‡ ––Š‡’‘™‡” ‘„‹‡”Ȁ•’Ž‹––‡”–‘–Š‡ —„•—•‹‰ǦƒŽ‡–‘ǦƒŽ‡ ‘ƒš‹ƒŽŒ—’‡”
ƒ„Ž‡ǣ
”‘–Š‡ˆ‹”•– —„ǯ•UPLINK ȋƒ†ͳǡƒ†ʹǡ‘”ƒ†͵Ȍ’‘”––‘–Š‡ˆ‹”•–’‘™‡”
‘„‹‡”Ȁ•’Ž‹––‡”
”‘–Š‡ˆ‹”•– —„ǯ•DOWNLINK ȋƒ†ͳǡƒ†ʹǡ‘”ƒ†͵Ȍ’‘”––‘–Š‡•‡ ‘†’‘™‡”
‘„‹‡”Ȁ•’Ž‹––‡”
”‘–Š‡•‡ ‘† —„ǯ•UPLINK ȋƒ†ͳǡƒ†ʹǡ‘”ƒ†͵Ȍ’‘”––‘–Š‡ˆ‹”•–’‘™‡”
‘„‹‡”Ȁ•’Ž‹––‡”
”‘–Š‡•‡ ‘† —„ǯ•DOWNLINK ȋƒ†ͳǡƒ†ʹǡ‘”ƒ†͵Ȍ’‘”––‘–Š‡•‡ ‘†’‘™‡”
‘„‹‡”Ȁ•’Ž‹––‡”
NOTE:
ConnectionsshouldnotcrossBands.Forexample,allBand1connectionsshouldbemadetothe
samehybridpowercombiner/splitterconnectedtotherepeaterBTSthatmatchestheBand1
frequency.
Š‡  —„•ǤȄˆ–‡” ‘‡ –‹‰ƒ†’‘™‡”‹‰‘–Š‡ —„ǡ Š‡ ƒŽŽ•–‘‡•—”‡–Šƒ–
–Š‡•›•–‡‹•‘’‡”ƒ–‹‰’”‘’‡”Ž›Ǥ
ƒ‡•—”‡–Š‡ƒ‹ —„‹•‰”‘—†‡†ǤThewarrantydoesnotcoverdamagecausedwhen
anungroundedHubispoweredon.
NOTE:
Usea50ohmterminatoronanyunusedpowercombiner/splitterports.
Page 154
Š 2013 TE Connectivity Ltd
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Interfacing the Fusion Wideband Main Hub to an RF Source
‹‰—”‡Ͷͷ•Š‘™•Š‘™–‘ ‘‡ ––™‘ —„•–‘ƒ†—’Ž‡š”‡’‡ƒ–‡”‘”„ƒ•‡•–ƒ–‹‘Ǥ‘—‡‡†–‘—•‡
‘‡ ‹” —Žƒ–‘”ƒ†‘‡‘”‡ ‘ƒš‹ƒŽŒ—’‡” ƒ„Ž‡ǡƒ••Š‘™Ǥ
Band 1
UL1
Band 2
UL2
Band 3
UL3
AC Power
Alarms
DL1
DL2
DL3
Band 1
UL1
Band 2
UL2
Band 3
UL3
AC Power
Alarms
N-male to N-male
coaxial-jumper cables
between Combiner/Splitter
and Fusion Main Hub’s
Uplink Port for either Band 1,
Band 2, or Band 3
DL1
DL2
DL3
N-male to N-male
coaxial-jumper cables
between Combiner/Splitter and
Fusion Main Hub’s Downlink Port
for either Band 1, Band 2, or Band 3
2 x 1 Power
Combiner/Splitter
2 x 1 Power
Combiner/Splitter
N-male to N-male
coaxial-jumper cable
Insert attenuator
(if needed)
N-male to N-male
coaxial-jumper cable
Circulator
Base Station
to Repeater or
N-male to N-male
coaxial-jumper cable
Figure45.Connecting Two Fusion Wideband Main Hub’s RF Band Ports to a Duplex Repeater or Base Station
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Page 155
Š 2013 TE Connectivity Ltd.
Installing Fusion Wideband
CONNECTINGCONTACTALARMSTOAFUSIONWIDEBANDSYSTEM
Š‡ —•‹‘‹†‡„ƒ†ƒ‹ —„ ƒ‰‡‡”ƒ–‡ȋ•‘—” ‡Ȍ–™‘ ‘–ƒ –ƒŽƒ”•ƒ•™‡ŽŽƒ••‡•‡–Š”‡‡
‡š–‡”ƒŽ ‘–ƒ –ƒŽƒ”Ǥ
•
AlarmSourceȄŠ‡ —•‹‘‹†‡„ƒ†ƒ‹ —„Šƒ•–™‘ƒŽƒ” ‘–ƒ –•ǡˆƒ—Ž–ȋƒŒ‘”Ȍƒ†
™ƒ”‹‰ȋ‹‘”ȌǤŠ‡•‡ ‘–ƒ –•ƒ”‡‘”ƒŽŽ›Ǧ Ž‘•‡†ȋȌƒ†™‹ŽŽ‘’‡™Š‡ƒ‹–‡”ƒŽ
ƒŽƒ”‹•†‡–‡ –‡†Ǥ ‘”ˆ—”–Š‡”‹ˆ‘”ƒ–‹‘ǡ•‡‡DzŽƒ”‘—” ‡dz‘’ƒ‰‡ͳͷ͹Ǥ
NOTE:
–
–
•
The contact can be changed to normallyͲopen (NO) with AdminBrowser. This is not
recommendedsincenoalarmwouldbesentifpowertotheFusionWidebandMainHubfails.
ƒ—Ž–‹•ƒ –‹˜ƒ–‡†™Š‡ƒ›ˆƒ—Ž–•‘”†‹• ‘‡ –•ƒ”‡†‡–‡ –‡†Ǥ
ƒ”‹‰‹•ƒ –‹˜ƒ–‡†™Š‡ƒ›™ƒ”‹‰ ‘†‹–‹‘•ƒ”‡†‡–‡ –‡†‡š ‡’–Ž‘ ‘—–‘”™Š‡
–Š‡‡†Ǧ–‘Ǧ‡†•›•–‡–‡•–‹•‘–˜ƒŽ‹†Ǥ
AlarmSenseȄŠ‡ —•‹‘‹†‡„ƒ†ƒ‹ —„ ƒ‘‹–‘”͵‡š–‡”ƒŽƒŽƒ” ‘–ƒ –•Ǥƒ Š
’‘”– ƒ„‡ ‘ˆ‹‰—”‡†ˆ‘”‘”ƒŽŽ›Ǧ‘’‡ȋȌ‘”‘”ƒŽŽ›Ǧ Ž‘•‡†ȋȌ ‘–ƒ –•ǤŠ‡
‹–‡”ˆƒ ‡‡š’‡ –•ƒ•‡–‘ˆˆŽ‘ƒ–‹‰ ‘–ƒ –•ǡƒ†ƒ‡š–‡”ƒŽ˜‘Ž–ƒ‰‡•‘—” ‡‹•‘–”‡“—‹”‡†ˆ‘”
–Š‹•‹–‡”ˆƒ ‡Ǥ•‡†‹”‘™•‡”–‘‘‹–‘”–Š‡’‘”–•–ƒ–—•Ǥ ‘”ˆ—”–Š‡”‹ˆ‘”ƒ–‹‘ǡ•‡‡
DzŽƒ”‡•‡dz‘’ƒ‰‡ͳ͸ͲǤ
ƒ„Ž‡ͻͲŽ‹•–•–Š‡ƒŽƒ”–›’‡•ǡ‡“—‹’‡––‘™Š‹ Š–Š‡ —•‹‘‹†‡„ƒ†ƒ‹ —„‹• ‘‡ –‡†ǡ
ƒ„Ž‡ȋ•Ȍ—•‡†ǡƒ†–Š‡ˆƒ—Ž–•ƒ†™ƒ”‹‰•–Šƒ–ƒ”‡†‡–‡ –‡†Ǥ
Table90. AlarmTypes
Alarm
Type
Fusion Wideband
Connected to
Cable(s) Used
Errors Detected
Source
FlexWave
5-port Alarm Daisy-Chain Cable
Faults
Source
BTS
5-port Alarm Daisy-Chain Cable
Faults and Warnings
In addition, a custom daisy-chain cable-to-BTS interface cable
is required. Make this interface cable to the desired length and
with the appropriate pin placement.
Sense
Unison
5-port Alarm Daisy-Chain Cable
Faults
and the Alarm Sense Adapter Cable
‘–‡–Šƒ– Ž‡šƒ˜‡ ‘ —••—’’‘”–•‘Ž›ˆƒ—Ž–•ȋƒŒ‘”‡””‘”•ȌǤ
Page 156
Š 2013 TE Connectivity Ltd
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Connecting Contact Alarms to a Fusion Wideband System
AlarmSource
—•‹‘‹†‡„ƒ†ƒŽ™ƒ›•ƒ –•ƒ•ƒƒŽƒ”•‘—” ‡ǡ‘ƒ––‡”™Šƒ––›’‡‘ˆ‡“—‹’‡–›‘—ƒ”‡
‘‡ –‹‰–‘Ǥ‡ˆ‡”–‘DzŽƒ”‡•‡dz‘’ƒ‰‡ͳ͸Ͳ‹ˆ›‘—™ƒ– —•‹‘‹†‡„ƒ†–‘•‡•‡‹•‘
‘–ƒ – Ž‘•—”‡•‘”‘–Š‡”‡š–‡”ƒŽƒŽƒ”•Ǥ
NOTE:
Thefollowingproceduresassumethatthesystemisinstalledandthathasbeenprogrammed
withbands.
UsingFlexWaveFocustoMonitorFusionWideband
Š‡›‘— ‘‡ – Ž‡šƒ˜‡ ‘ —•–‘–Š‡ —•‹‘‹†‡„ƒ†ǡ–Š‡ —•‹‘‹†‡„ƒ†ƒ‹ —„‹•
–Š‡‘—–’—–‘ˆ–Š‡ƒŽƒ”•ȋƒŽƒ”•‘—” ‡Ȍƒ† ‘ —•‹•–Š‡‹’—–ȋƒŽƒ”•‡•‡Ȍǡƒ••Š‘™‹
‹‰—”‡Ͷ͸Ǥ ‘ —••—’’‘”–•‘Ž›ˆƒ—Ž–•ȋƒŒ‘”‡””‘”•ȌǤ
Fusion Main Hub
Band 1
UL1
Band 2
UL2
Band 3
UL3
AC Power
Alarms
DL1
DL2
DL3
Alarm
Source
May need
9-pin Adapter
that ships
with the cable
5-port Alarm Daisy-Chain Cable
Alarm
Sense
Band 1
UL1
Band 2
UL2
Band 3
UL3
AC Power
Alarms
DL1
DL2
DL3
Alarm
Source
Figure46.Connecting FlexWave to Fusion Wideband
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Page 157
Š 2013 TE Connectivity Ltd.
Installing Fusion Wideband
UsingaBaseStationtoMonitorFusionWideband
NOTE:
TheBTSmustbeconfigured,bythecarrier,forcontactclosuremonitoringpriortoconnectinga
FusionWidebandMainHubtoit.
Š‡›‘— ‘‡ –ƒ–‘ —•‹‘‹†‡„ƒ†ǡ–Š‡ —•‹‘‹†‡„ƒ†ƒ‹ —„‹•–Š‡‘—–’—–‘ˆ–Š‡
ƒŽƒ”•ȋƒŽƒ”•‘—” ‡Ȍƒ†–Š‡‹•–Š‡‹’—–ȋƒŽƒ”•‡•‡Ȍǡƒ••Š‘™‹ ‹‰—”‡Ͷ͹Ǥ‹–‡”ˆƒ ‡
ƒ„Ž‡‹•”‡“—‹”‡†„‡–™‡‡–Š‡†ƒ‹•›Ǧ Šƒ‹ ƒ„Ž‡ƒ†–Š‡Ǥ‡ ƒ—•‡ƒŽƒ”‹–‡”ˆƒ ‡’‹‘—–•
ƒ† —•‹‘‹†‡„ƒ†Ǧ–‘Ǧ†‹•–ƒ ‡•˜ƒ”›ǡ–Š‹• ƒ„Ž‡‹•‘ˆ–‡ —•–‘ƒ†™‹”‡†‘Ǧ•‹–‡Ǥ‡ˆ‡”
–‘Dz’–‹ ƒŽ ‹„‡”’Ž‹Ȁ‘™Ž‹‘”–•dz‘’ƒ‰‡͵͵ˆ‘”Žƒ”‘–ƒ –†‡–ƒ‹Ž•ȋ‘”ƒŽŽ›Ž‘•‡†ȌǤ
Fusion Main Hub
Band 1
UL1
Band 2
UL2
Band 3
UL3
AC Power
Alarms
DL1
DL2
DL3
Alarm
Source
Band 1
UL1
Band 2
UL2
5-port Alarm Daisy-Chain Cable
Alarm
Sense
BTS
Interface
Cable
(custom-made, on-site)
Band 3
UL3
AC Power
Alarms
DL1
DL2
DL3
Alarm
Source
Figure47.Using a BTS to Monitor Fusion Wideband
NOTE:
Fornormallyopencontacts,thefaultandwarningcontactsneedtobewiredinparallelwith
otherMainHubs.
NOTE:
TEdoesnotrecommendusingnormallyopencontacts.
Page 158
Š 2013 TE Connectivity Ltd
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Connecting Contact Alarms to a Fusion Wideband System
UsingaBaseStationandAdminBrowsertoMonitorFusionWideband
NOTE:
TheBTSmustbeconfigured,bythecarrier,forcontactclosuremonitoringpriortoconnectinga
FusionWidebandMainHubtoit.
‘”†‡”–‘–ƒ‡ˆ—ŽŽƒ†˜ƒ–ƒ‰‡‘ˆ —•‹‘‹†‡„ƒ†ǯ•Ƭ ƒ’ƒ„‹Ž‹–‹‡•›‘— ƒ—•‡
†‹”‘™•‡”•‘ˆ–™ƒ”‡‹ƒ††‹–‹‘–‘ƒ–‘‘‹–‘”–Š‡•›•–‡ǡƒ••Š‘™‹ ‹‰—”‡ͶͺǤ‡ˆ‡”
–‘Dz –‡”ˆƒ ‡dz‘’ƒ‰‡ͳ͹ʹˆ‘”‘’–‹‘ƒŽˆ‡ƒ–—”‡ ƒ’ƒ„‹Ž‹–‹‡•Ǥ
Fusion Main Hub
Band 1
Modem
UL1
Band 2
UL2
Band 3
UL3
AC Power
Alarms
DL1
DL2
DL3
5-port Alarm Daisy-Chain Cable
Alarm
Source
Band 1
Modem
UL1
Band 2
UL2
Alarm
Sense
BTS
Interface
Cable
(custom-made, on-site)
Band 3
UL3
AC Power
Alarms
DL1
DL2
DL3
Alarm
Source
Line Switch
PSTN
Modem
PC running
Standard
Browser
Software
Figure48.Using a BTS and AdminBrowserto Monitor Fusion Wideband
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Page 159
Š 2013 TE Connectivity Ltd.
Installing Fusion Wideband
AlarmSense
•‡†‹”‘™•‡”–‘‡ƒ„Ž‡–Š‡ —•‹‘‹†‡„ƒ†•›•–‡ˆ‘”DzƒŽƒ”•‡•‡dz™Š‡ ‘‡ –‹‰–‘
–Š‡ ‘–ƒ – Ž‘•—”‡‘ˆ‹•‘ƒ‹ —„•‘”‘–Š‡”‡š–‡”ƒŽƒŽƒ”•ȋ”‡ˆ‡”–‘‡–‘–ƒ –‡•‡
”‘’‡”–‹‡•‹–Š‡AdminBrowserUserManualȌǤ
NOTE:
Thisprocedureassumesthatthesystemisinstalledandthathasbeenprogrammedwithbands.
Š‡›‘— ‘‡ –‹•‘–‘ —•‹‘‹†‡„ƒ†ǡ–Š‡ —•‹‘‹†‡„ƒ†ƒ‹ —„‹•–Š‡‹’—–‘ˆ–Š‡
ƒŽƒ”•ȋƒŽƒ”•‡•‡Ȍƒ†–Š‡‹•‘‹•–Š‡‘—–’—–ȋƒŽƒ”•‘—” ‡Ȍǡƒ••Š‘™‹ ‹‰—”‡ͶͻǤŠ‡
‹’—–ƒŽƒ”•‡•‡‡‡†•–‘„‡•‡––‘‘”ƒŽŽ› Ž‘•‡†ȋȌǤ
Up to 5 Unison Main Hubs
Fusion Main Hub
5-port Alarm Daisy-Chain Cable
Alarm Sense
Adapter Cable
Alarm
Sense
Alarm
Source
Alarm
Source
Figure49.Using Fusion Wideband to Monitor Unison
‹•‘•—’’‘”–•‘Ž›ˆƒ—Ž–•Ǥ‘——•–—•‡–Š‡Žƒ”‡•‡†ƒ’–‡”ƒ„Ž‡–‘‹–‡”ˆƒ ‡–Š‡
†ƒ‹•›Ǧ Šƒ‹ ƒ„Ž‡–‘ —•‹‘‹†‡„ƒ†ǤŠ‡ƒ†ƒ’–‡” ƒ„Ž‡‹•”‡“—‹”‡†„‡ ƒ—•‡‹––”ƒ•Žƒ–‡•–Š‡
‹•‘ˆƒ—Ž–’‹‘—––‘–Š‡•‡•‡‹’—–’‹•‘–Š‡ —•‹‘‹†‡„ƒ†ƒ‹ —„Ǥ
+5V
External
Equipment
Contacts
Diagnostic 1
Figure50.Alarm Sense Contacts
Page 160
Š 2013 TE Connectivity Ltd
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Connecting Contact Alarms to a Fusion Wideband System
AlarmCables
‹‰—”‡ͷͳ•Š‘™•–Š‡ͷǦ’‘”–Žƒ”ƒ‹•›ǦŠƒ‹ƒ„Ž‡ȋͶͲʹͶǦ͵Ȍǡ™Š‹ Š•—’’‘”–•ˆƒ—Ž–ƒ†
™ƒ”‹‰ ‘†‹–‹‘•Ǥ
1.2 meters (4 feet)
DB-9 female to
Base Station,
FlexWave Focus,
or the Alarm Sense
Adapter Cable when
connecting Unison
Splice
J1
Female 4
J2
Male
Splice
Connector
Hood
DB-9 male to Fusion,
Unison, FlexWave Focus,
Alarm Port
Splice
.5 meter
(1.5 feet)
Splice
DB-9 male to Fusion,
Unison, FlexWave Focus,
Alarm Port
J3
Male
DB-9 male to Fusion,
Unison, FlexWave Focus,
Alarm Port
.5 meter
(1.5 feet)
Splice
Splice
NOTE: Do not daisy-chain
Fusion Main Hubs
with FlexWave Focus
if you want both faults
and warnings from Fusion.
Only faults are reported if
you combine Fusion with
FlexWave in the same daisy
chain.
J4
Male
.5 meter
(1.5 feet)
Splice
J5
Male
DB-9 male to Fusion,
Unison, FlexWave Focus,
Alarm Port
Splice
.5 meter
(1.5 feet)
Option 1: DB-9 to Fusion,
Unison, FlexWave Focus
Alarm Port. J7 not used.
J6
Male
.25 meter
(.75 feet)
J7
Female
Terminator
Option 2: Use J2-J5
for Alarm ports. Use J6 to
connect to an additional
Alarm Daisy-Chain Cable.
Do not use J7.
Option 3: Connect
fewer than 5 ports and
connect J7 to the lowest
unused port to terminate
the daisy chain.
Figure51.5-port Alarm Daisy-Chain Cable
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Page 161
Š 2013 TE Connectivity Ltd.
Installing Fusion Wideband
ALARMMONITORINGCONNECTIVITYOPTIONS
NOTE:
Thefollowingproceduresassumethatthesystemisinstalledandthathasbeenprogrammed
withbands.
DirectConnection
–Š‹• ‘ˆ‹‰—”ƒ–‹‘ǡ–Š‡ ‘‡ –•†‹”‡ –Ž›–‘–Š‡RJ-45 100 BASE-T ’‘”–‘–Š‡ —•‹‘‹†‡„ƒ†
ƒ‹ —„ǯ•ˆ”‘–’ƒ‡Ž—•‹‰ƒ–Š‡”‡– ”‘••Ǧ‘˜‡” ƒ„Ž‡Ǥ
AdminBrowser is
resident in Fusion.
Cross-over
100 BASE-T Cable
PC running
Standard
Browser
Software
Figure52.OA&M Direct Connection
ModemConnection
–Š‹• ‘ˆ‹‰—”ƒ–‹‘ǡ–Š‡ƒ†–Š‡ —•‹‘‹†‡„ƒ†ƒ‹ —„ ‘‡ ––‘ƒƒŽ‘‰‘†‡•ƒ†
‘—‹ ƒ–‡—•‹‰ƒ•–ƒ†ƒ”††‹ƒŽǦ—’–‡Ž‡’Š‘‡ ‘‡ –‹‘Ǥ
#4028-10
Straight-Through
Modem cable
Modem
#140272-0
PSTN
Modem
#4028-10
Straight-Through
Modem cable
PC running
Standard
Browser
Software
#140272-0
Figure53.OA&M Modem Connection
NOTE:
Referto“CoaxialCable”onpage198forthemodemcablewiringinformation.
Page 162
Š 2013 TE Connectivity Ltd
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Alarm Monitoring Connectivity Options
‘†‡•™‹– Š•‡––‹‰•ƒ”‡ƒ•ˆ‘ŽŽ‘™•ˆ‘”‘„‘–‹ •‘†‡ǣ
•
•
Ǧ•‹†‡ǣͳǡʹƒ†͸’
—•‹‘‹†‡„ƒ† —„Ǧ•‹†‡ǣʹƒ†͸’Ǥ
SettingUpFusionWidebandModem(USRModem)UsingAdminBrowser
•‡–Š‡ˆ‘ŽŽ‘™‹‰•–‡’•–‘•‡–—’ƒ‹ƒŽǦ ‘ —•‹‘‹†‡„ƒ†ǣ
–ƒ”–†‹”‘™•‡”ƒ•‡š’Žƒ‹‡†‹–Š‡†‹”‘™•‡”ƒ—ƒŽǤ
‡Ž‡ –SystemConfigurationǤ
SelectSetupModemConnectionǤ–Š‡™‹†‘™•Š‘™„‡Ž‘™‘’‡•ǣ
TE
ƒ‡•—”‡–Š‡‘†‡–›’‡‹•ǣ‘‡Ǥ
•
•
Š‡‘†‡‹‹–•–”‹‰‹•ˆ‘”ƒ‘†‡
Š‡•‡”˜‡”ƒ††”‡••‹•–Š‡ ƒ††”‡••‘ˆ–Š‡
Ž‹ SetupConnectionǤ
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Page 163
Š 2013 TE Connectivity Ltd.
Installing Fusion Wideband
SettingUpaPCModemUsingWindows
•‡–Š‡ˆ‘ŽŽ‘™‹‰•‡–•–‘•‡–—’ƒ†‹ƒŽǦ—’ ‘‡ –‹‘‘›‘—”Ǥ
Ž‹ StartǡSettingsǡNetworkConnectionsǤŠ‡™‹†‘™•Š‘™„‡Ž‘™‘’‡•Ǥ
ClickCreateanewconnectionǤŠ‡™‹†‘™•Š‘™„‡Ž‘™‘’‡•Ǥ
Page 164
Š 2013 TE Connectivity Ltd
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Alarm Monitoring Connectivity Options
Ž‹ NextǤŠ‡™‹†‘™•Š‘™‹–Š‡ˆ‘ŽŽ‘™‹‰‰”ƒ’Š‹ ‘’‡•Ǥ
‡Ž‡ –Connecttothenetworkatmyworkplaceƒ† Ž‹ NextǢ–Š‡™‹†‘™•Š‘™„‡Ž‘™
‘’‡•Ǥ
‡Ž‡ –DialǦupconnectionƒ† Ž‹ NextǢ–Š‡™‹†‘™•Š‘™„‡Ž‘™‘’‡•Ǥ
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Page 165
Š 2013 TE Connectivity Ltd.
Installing Fusion Wideband
›’‡ƒƒ‡ˆ‘”–Š‹• ‘‡ –‹‘ƒ† Ž‹ NextǢ–Š‡™‹†‘™•Š‘™„‡Ž‘™‘’‡•Ǥ
›’‡–Š‡†‡•‹”‡††‹ƒŽ‹Phonenumberƒ† Ž‹ NextǢ–Š‡™‹†‘™•Š‘™„‡Ž‘™‘’‡•Ǥ
‡Ž‡ –Anyone’suseƒ† Ž‹ NextǢ–Š‡™‹†‘™•Š‘™„‡Ž‘™‘’‡•Ǥ
Page 166
Š 2013 TE Connectivity Ltd
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Alarm Monitoring Connectivity Options
10
Ž‹ FinishǢ–Š‡™‹†‘™•Š‘™„‡Ž‘™‘’‡•Ǥ
›’‡ƒ’ƒ••™‘”†ƒ•‹†‹ ƒ–‡†ƒ† Ž‹ PropertiesǢ–Š‡™‹†‘™•Š‘™„‡Ž‘™‘’‡•Ǥ
Š‡†‡ˆƒ—Ž–’ƒ”ƒ‡–‡”•ƒ”‡ƒ•ˆ‘ŽŽ‘™•ǣ
•
•
•‡”ƒ‡ǣppp_user
ƒ••™‘”†ȋ‘‡™‘”†ǡƒŽŽŽ‘™‡” ƒ•‡Ȍǣpassword
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Page 167
Š 2013 TE Connectivity Ltd.
Installing Fusion Wideband
11
Ž‹ Configure...Š‡™‹†‘™•Š‘™„‡Ž‘™‘’‡•Ǥ
12
‡Ž‡ ––Š‡‘†‡•’‡‡†ƒ†‘–Š‡”’ƒ”ƒ‡–‡”•ˆ‘”›‘—”‘†‡ƒ•†‡•‹”‡†ƒ† Ž‹ OKǤ
13
14
‡Ž‡ ––Š‡Security–ƒ„Ǣ–Š‡™‹†‘™•Š‘™„‡Ž‘™‘’‡•Ǥ
‡Ž‡ –Typicalƒ†–Š‡ Ž‹ –Š‡Networking–ƒ„Ǣ–Š‡™‹†‘™•Š‘™„‡Ž‘™‘’‡•Ǥ
Page 168
Š 2013 TE Connectivity Ltd
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Alarm Monitoring Connectivity Options
15
‡Ž‡ –InternetProtocol(TCP/IP)ƒ••Š‘™ƒ† Ž‹ PropertiesǢ–Š‡™‹†‘™•Š‘™„‡Ž‘™
‘’‡•Ǥ
16
‡Ž‡ –ObtainanIPaddressautomaticallyƒ†ObtainDNSserveraddressautomaticallyǡƒ†
–Š‡ Ž‹ OKǤ
17
‘ ‘‡ ––‘–Š‡ —•‹‘‹†‡„ƒ† —„‘˜‡”–Š‡‹ƒŽǦ—’ ‘‡ –‹‘ǡ•–ƒ”–›‘—™‡„„”‘™•‡”
ƒ†–Š‡‹–Š‡ƒ††”‡••„ƒ”ǡ–›’‡–Š‡•‡”˜‡” ƒ††”‡•• ‘ˆ‹‰—”‡†‹Dz‡––‹‰’ —•‹‘
‹†‡„ƒ†‘†‡ȋ‘†‡Ȍ•‹‰†‹”‘™•‡”dz‘’ƒ‰‡ͳ͸͵Ǥ
100BASEͲTPortExpanderConnection
–Š‹• ‘ˆ‹‰—”ƒ–‹‘ƒ•™‹– Š‹•—•‡†–‘ƒŽŽ‘™–Š‡ ‘‡ –‹‘‘ˆ—Ž–‹’Ž‡†‡˜‹ ‡•–‘ƒ•‹‰Ž‡
™‹–ŠƒͳͲͲǦ’‘”–Ǥ‡•–‹‰™ƒ•’‡”ˆ‘”‡†™‹–Šƒ‹•›•ͶǦ’‘”–•™‹– ŠǤƒ Š —•‹‘
‹†‡„ƒ† —•–Šƒ˜‡ƒ—‹“—‡ ƒ††”‡••Ǥ
AdminBrowser is
resident in Fusion.
100 BASE-T Cable
RJ-45 Male to RJ-45 Male
LAN Switch
100 BASE-T
Ethernet connection
PC running
Standard
Browser
Software
Figure54.OA&M Connection using a 232 Port Expander
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Page 169
Š 2013 TE Connectivity Ltd.
Installing Fusion Wideband
POTSLineSharingSwitchConnection
•‹‰ƒŽ‹‡•Šƒ”‹‰•™‹– Šǡ›‘— ƒ ‘‡ ––™‘‘”‘”‡‘†‡•–‘ƒ•‹‰Ž‡–‡Ž‡’Š‘‡Ž‹‡Ǥ
PC running
Standard
Browser
Software
4- or 8-port
4-port: #240031-0
8-port: #240052-0
#4028-10
Straight-Through
Modem cable
Modem
#140272-0
Line Sharing Switch
PSTN
Standard
phone
cable
Modem
Up to 4 modems
per switch
Modem
#140272-0
#4028-10 Straight-Through
Modem cable
Figure55.OA&M Connection Using a POTS Line Sharing Switch
Page 170
Š 2013 TE Connectivity Ltd
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Alarm Monitoring Connectivity Options
4- or 8-port
Line Sharing Switch PNs:
4-port: #240031-0
8-port: #240052-0
PC running
Standard
Browser
Software
#4028-10
Straight-Through
Modem cable
Modem
#140272-0
4- or 8-Port
Line Sharing Switch
PSTN
Standard phone cable
4- or 8-Port
Line Sharing Switch
4- or 8-Port
Line Sharing Switch
4- or 8-Port
Line Sharing Switch
4- or 8-Port
Line Sharing Switch
#4028-10
Straight-Through
Modem cable
Figure56.Cascading Line Sharing Switches
EthernetRFModem
—•‹‘‹†‡„ƒ† ƒƒŽ•‘—•‡ƒ–Š‡”‡–Ǧ„ƒ•‡† ‘†‡Ǥ —•–ƒ„‘—–ƒ› ‘†‡™‹ŽŽ™‘”ǡ
ƒŽ–Š‘—‰Š‘†‡•–Šƒ–•—’’‘”–‘”–††”‡••”ƒ•Žƒ–‹‘ƒ”‡„‡•–Ǥ
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Page 171
Š 2013 TE Connectivity Ltd.
Installing Fusion Wideband
EthernetLANConnection
–Š‡”‡– ‘‡ –‹‘ ƒ„‡—•‡†–‘ ‘—‹ ƒ–‡„‡–™‡‡–Š‡ƒ† —•‹‘‹†‡„ƒ†Ǥ
‡•–‹‰™ƒ•’‡”ˆ‘”‡†™‹–Šƒ‹•›•ͶǦ’‘”–•™‹– ŠǤ
100 BASE-T Cable
Male RJ-45 to Male RJ-45
PC running
Standard
Browser
Software
Ethernet
TCP/IP
Ethernet
LAN Switch
Figure57.OA&M Connection Using Ethernet and ENET/232 Serial Hub
SNMPInterface
ƒ—Ž–•ƒ†™ƒ”‹‰• ƒƒŽ•‘„‡†‹ƒ‰‘•‡†™‹–Š—•‹‰ƒ•–ƒ†ƒ”†ȋȌ‡–™‘”
ƒƒ‰‡‡–•›•–‡ȋ‘’–‹‘ƒŽȌǤ”‡•‹†‡–•‘ˆ–™ƒ”‡‹ —•‹‘‹†‡„ƒ†’”‘˜‹†‡•
‹–‡”ƒ –‹‘•ˆ‘””ƒ’•ƒ†‘–‹ˆ‹ ƒ–‹‘Ǥ
Š‡ —•‹‘‹†‡„ƒ†‹ Ž—†‡•ƒ ˆ‘”‹–‡‰”ƒ–‹‰‹–‘–Š‡‡–™‘”ƒƒ‰‡‡–›•–‡
ȋȌƒ†•—’’‘”–•˜ͳƒ†˜ʹ Ǥ
Page 172
Š 2013 TE Connectivity Ltd
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Alarm Monitoring Connectivity Options
Main Hub
PPP Modem
PPP Modem
Expansion Hub
Remote Unit
PSTN
RS-232
Modem Port
Remote Unit
(b) Connection to multiple systems through Dial-in router
Main Hub
Dialup Router/
Firewall
Ethernet
Port
Ethernet
Port
LAN
Modem
Router
PSTN
PPP
PPP
Expansion Hub
Remote Unit
Remote Unit
(c) DSL Modem through internet
Main Hub
Router
DSL Modem
Ethernet
Port
Switch
DSL Modem
Router
Ethernet
Port
Expansion Hub
Remote Unit
PSTN/
Internet
Remote Unit
(d) Connection to corporate LAN through firewall
Main Hub
Firewall
Router
Ethernet
Port
LAN
Router
Internet
Ethernet Port
Figure58.Fusion Wideband SNMP Configuration Options
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Page 173
Š 2013 TE Connectivity Ltd.
Installing Fusion Wideband
Page 174
Š 2013 TE Connectivity Ltd
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
REPLACINGFUSIONWIDEBANDCOMPONENTS
Topics
Page
ReplacinganRAU................................................................................................................................................................. 176
ReplacetheRAU .....................................................................................................................................................................176
PerformSystemTest ..............................................................................................................................................................176
ChecktheRAULEDs ...............................................................................................................................................................177
ReplacingaFusionWidebandExpansionHub ...................................................................................................................... 178
ReplaceaFusionWidebandExpansionHub...........................................................................................................................178
AdminBrowserTasks ..............................................................................................................................................................178
ChecktheExpansionHubLEDs...............................................................................................................................................178
ReplacingaFusionWidebandMainHub .............................................................................................................................. 179
ReplaceaFusionWidebandMainHub...................................................................................................................................179
ConfiguretheNewFusionWidebandMainHub....................................................................................................................179
ChecktheLEDsontheNewMainHub ...................................................................................................................................180
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Page 175
Š2013 TE Connectivity Ltd.
Replacing Fusion Wideband Components
REPLACINGANRAU
CAUTION!
ThenewRAUmustsupportthesamebandsastheoneyouarereplacing.IftheRAUisofthe
wrongbandcombination,itwillnotoperateproperlyinthesystem.
3 ReplacetheRAU
10
11
•‹‰†‹”‘™•‡”ǡŽ‘‰‹ƒ† Ž‹ SYSTEM INFORMATIONǤ
Ž‹ SHOW SYSTEM TREEǡ•‡Ž‡ – —•‹‘‹†‡„ƒ†ƒ‹ —„ǡƒ† Ž‹ GET SYSTEM INFORMATION.
ŽŽ•›•–‡•‡––‹‰•ˆ‘” —„•ƒ†•™‹ŽŽ„‡†‹•’Žƒ›‡†Ǥ”‹–‡†‘™‘”•ƒ˜‡–Š‡’Ž‹ƒ†
‘™Ž‹––‡—ƒ–‹‘•‡––‹‰•‘›‘— ƒ•‡––Š‡‡™™‹–Š–Š‡•ƒ‡•‡––‹‰•Ǥ
Ž‹ CANCEL–‘ Ž‘•‡–Š‡™‹†‘™Ǥ
‡”‹ˆ›–Šƒ––Š‡‡™‹•‘ˆ–Š‡•ƒ‡ˆ”‡“—‡ ›„ƒ†•ƒ•–Š‡‘‡”‡’Žƒ ‡†Ǥ
‹• ‘‡ ––Š‡ ƒ„Ž‡ƒ†ƒ–‡ƒ ƒ„Ž‡ˆ”‘–Š‡—‹––‘„‡”‡’Žƒ ‡†Ǥ
•–ƒŽŽ–Š‡‡™Ǥ
‘‡ ––Š‡ƒ–‡ƒ ƒ„Ž‡ƒ†–Š‡–Š‡ ƒ„Ž‡–‘–Š‡‡™Ǥ
Ž‹ SYSTEM CONFIGURATION.
Ž‹ SHOW SYSTEM TREEǤ
‡Ž‡ ––Š‡ —•‹‘‹†‡„ƒ†”‡’Žƒ ‡†ƒ† Ž‹ EDIT UNIT PROPERTIESǤ
‡––Š‡ƒ––‡—ƒ–‹‘‘ˆ‡ƒ Š„ƒ†ƒ•–Š‡‘Ž†™ƒ•’”‘‰”ƒ‡†ƒ† Ž‹ SAVE PROPERTIESǤ
3 PerformSystemTest
Š‡ ‘˜‡‹‡–ǡ’‡”ˆ‘”›•–‡‡•––‘‘’–‹‹œ‡’‡”ˆ‘”ƒ ‡Ǥ
CAUTION!
DuringSystemTest,theentiresystemistemporarilyoffͲlineandnoRFisbeingtransmitted.
Page 176
Š 2013 TE Connectivity Ltd
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Replacing an RAU
3 ChecktheRAULEDs
Š‡ǯ•LINKƒ†ALARM••Š‘—Ž†„Ž‹ȋ‰”‡‡Ȁ”‡†Ȍ‘’‘™‡”—’Ǥ
ˆ–Š‡•†‘‘–„Ž‹‘’‘™‡”—’ǡ”‡’Žƒ ‡–Š‡Ǥ
ˆ–‡”•‡˜‡”ƒŽ•‡ ‘†•„‘–Š••Š‘—Ž† Šƒ‰‡–‘‰”‡‡ǡ™Š‹ Š‹†‹ ƒ–‡•–Šƒ––Š‡—‹–Šƒ•
„‡‡•— ‡••ˆ—ŽŽ›”‡’Žƒ ‡†ǡ–Š‡”‡‹• ‘—‹ ƒ–‹‘™‹–Š–Š‡ —„ǡƒ†–Š‡„ƒ†‹•
‘””‡ –Ǥ
a ˆ–Š‡LINK”‡ƒ‹•‰”‡‡ƒ†–Š‡ALARM”‡ƒ‹•”‡†ǡ˜‡”‹ˆ›–Šƒ––Š‡‘†‡Ž
‹• ‘””‡ –ˆ‘”–Š‡‹–‡†‡†ˆ”‡“—‡ ›„ƒ†Ǥ
‹• ‘‡ ––Š‡ ƒ„Ž‡ƒ†–Š‡”‡ ‘‡ –‹–‘ ‡Ǣ†‘‹‰–Š‹•‘”‡–Šƒ‘ ‡™‹ŽŽ‘–
Šƒ‰‡–Š‡”‡•—Ž–Ǥ
ˆ„‘–Š••–‹ŽŽ†‘ǯ– Šƒ‰‡–‘‰”‡‡ǡ—•‡†‹”‘™•‡”–‘†‡–‡”‹‡–Š‡‡šƒ –ƒ–—”‡
‘ˆ–Š‡ˆƒ—Ž–ƒ†•‡‡ƒ”‡ ‘‡†ƒ–‹‘‘ˆŠ‘™–‘ ‘””‡ –‹–Ǥ
ˆ„‘–Š•–—””‡†ȋƒˆ–‡”ͻͲ•‡ ‘†•Ȍǡ–Š‡ —„Šƒ•–‡”‹ƒ–‡† ‘—‹ ƒ–‹‘•Ǥ
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Page 177
Š 2013 TE Connectivity Ltd.
Replacing Fusion Wideband Components
REPLACINGAFUSIONWIDEBANDEXPANSIONHUB
3 ReplaceaFusionWidebandExpansionHub
—”‘ˆˆ–Š‡’‘™‡”–‘–Š‡š’ƒ•‹‘ —„Ǥ
‹• ‘‡ –ƒŽŽ ƒ„Ž‡•ǡ„‘–Šˆ‹„‡” ƒ„Ž‡•ǡƒ†–Š‡’‘™‡” ‘”†Ǥ
‡’Žƒ ‡–Š‡š’ƒ•‹‘ —„™‹–Šƒ‡™‘‡Ǥ
‘‡ ––Š‡’‘™‡” ‘”†ǡƒŽŽ ƒ„Ž‡•ǡƒ†„‘–Šˆ‹„‡” ƒ„Ž‡•Ȃ”‡‡„‡”‹‰–‘ Ž‡ƒƒ†
‘””‡ –Ž› ‘‡ ––Š‡—’Ž‹ƒ††‘™Ž‹ˆ‹„‡”Ǥ
—”‘–Š‡’‘™‡”–‘–Š‡š’ƒ•‹‘ —„Ǥ
3 AdminBrowserTasks
•
•
Š‡ƒ‹ —„ƒ—–‘ƒ–‹ ƒŽŽ›‹••—‡•–Š‡„ƒ†•‡––‹‰Ǥ
Š‡ ‘˜‡‹‡–ǡ—•‡†‹”‘™•‡”–‘’‡”ˆ‘”›•–‡‡•–‹‘”†‡”–‘‘’–‹‹œ‡
’‡”ˆ‘”ƒ ‡Ǥ
CAUTION!
DuringSystemTest,theentiresystemistemporarilyoffͲlineandnoRFisbeingtransmitted.For
afullyloadedsystem(oneMainHub,fourExpansionHubs,and32RAUs),itcantakeupto90
secondstocompletethetest.
3 ChecktheExpansionHubLEDs
•
•
•
•
Š‡••Š‘—Ž†„Ž‹–Š”‘—‰ŠƒŽŽ•–ƒ–‡•‘’‘™‡”—’Ǥ
– ˆ–Š‡•†‘‘–„Ž‹‘’‘™‡”—’ǡ”‡’Žƒ ‡–Š‡š’ƒ•‹‘ —„Ǥ
– ˆ–Š‡•†‘‘–‹ŽŽ—‹ƒ–‡ƒ–ƒŽŽǡƒ‡•—”‡–Š‡’‘™‡” ƒ„Ž‡‹• ‘‡ –‡†Ǥ
Š‡UL STATUSƒ†DL STATUS••Š‘—Ž†„‡‰”‡‡Ǥ
Š‡E-HUB STATUS ƒ†POWER••Š‘—Ž†„‡‰”‡‡Ǥ
‘”‡ƒ Š’‘”––Šƒ–Šƒ•ƒ ‘‡ –‡†–Š‡••Š‘—Ž†„‡‰”‡‡Ǥ
– ƒ–ƒ‡•‡˜‡”ƒŽ•‡ ‘†•ˆ‘”‡ƒ Š ‘‡ –‹‘ˆ‘”–Š‡•–‘†‹•’Žƒ›’”‘’‡”Ž›Ǥ
NOTE:
RefertoDz”‘—„Ž‡•Š‘‘–‹‰•‹‰•dz‘’ƒ‰‡ͳͺ͸fortroubleshootingusingtheLEDs.
Page 178
Š 2013 TE Connectivity Ltd
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Replacing a Fusion Wideband Main Hub
REPLACINGAFUSIONWIDEBANDMAINHUB
‘——•–”‡ ‘”†–Š‡•›•–‡ ‘ˆ‹‰—”ƒ–‹‘•‡––‹‰•ˆ”‘–Š‡‘Ž† —•‹‘‹†‡„ƒ†ƒ‹ —„ǯ•
‡‘”›„‡ˆ‘”‡”‡’Žƒ ‹‰–Š‡—‹–Ǥ‘—™‹ŽŽ’”‘‰”ƒ–Š‡‡™ƒ‹ —„™‹–Š–Š‹•‹ˆ‘”ƒ–‹‘Ǥ ˆ
–Š‡ƒ‹ —„‹•’”‘‰”ƒ‡†‹ ‘””‡ –Ž›ǡ–Š‡•›•–‡™‹ŽŽ‘–™‘”Ǥ ˆ–Š‡ —„–‘„‡”‡’Žƒ ‡†‹•
‘–ˆ— –‹‘‹‰ƒ†›‘— ƒ‘–—•‡†‹”‘™•‡”ǡ‰‡––Š‡ ‘ˆ‹‰—”ƒ–‹‘•‡––‹‰•ˆ”‘–Š‡
•Ǧ—‹Ž–‘ —‡––Šƒ–™ƒ• ”‡ƒ–‡†ƒ•’ƒ”–‘ˆ–Š‡‘”‹‰‹ƒŽ‹•–ƒŽŽƒ–‹‘Ǥ
3 ReplaceaFusionWidebandMainHub
•‹‰†‹”‘™•‡”ǡŽ‘‰‹ǡ Ž‹ SYSTEM INFORMATIONǡ Ž‹ SHOW SYSTEM TREEǡ•‡Ž‡ – —•‹‘
‹†‡„ƒ† —„ǡ Ž‹ GET SYSTEM INFORMATIONǤ
—”‘ˆˆ–Š‡’‘™‡”–‘–Š‡ —•‹‘‹†‡„ƒ†ƒ‹ —„Ǥ
‹• ‘‡ –ƒŽŽ ƒ„Ž‡•ƒ†–Š‡’‘™‡” ‘”†Ǥ
‡’Žƒ ‡–Š‡ƒ‹ —„™‹–Šƒ‡™‘‡Ǥ
‘‡ ––Š‡’‘™‡” ‘”†ƒ†ƒŽŽ ƒ„Ž‡•Ǥ
‘‡ ––Š‡ ”‘••‘˜‡”–Š‡”‡– ƒ„Ž‡–‘–Š‡ƒ†–Š‡–‘–Š‡ƒ‹ —„ǯ•ˆ”‘–’ƒ‡Ž
ͳͲͲƒ•‡Ǧ ‘‡ –‘”Ǥ Ȁ’‘”–Ȍ
–ƒ”––Š‡•–ƒ†ƒ”†„”‘™•‡”‘–Š‡–‘ ‘—‹ ƒ–‡™‹–Š†‹”‘™•‡”•‘ˆ–™ƒ”‡Ǥ
—”‘–Š‡’‘™‡”–‘–Š‡ƒ‹ —„Ǥ
„•‡”˜‡–Š‡•ƒˆ–‡”–—”‹‰‘–Š‡’‘™‡”Ǥ
ŽŽ–Š‡•„Ž‹†—”‹‰–Š‡‹‹–‹ƒŽ’‘™‡”—’•‡“—‡ ‡ǤŽŽ••Š‘—Ž†–—”‰”‡‡ƒˆ–‡”–Š‡
’‘™‡”‘•‡“—‡ ‡‹• ‘’Ž‡–‡Ǥ‘™‡”—’•‡“—‡ ‡–ƒ‡•„‡–™‡‡ͳƒ†ʹ‹—–‡•
†‡’‡†‹‰‘–Š‡—„‡”‘ˆ•Ǥ
3 ConfiguretheNewFusionWidebandMainHub
CAUTION!
10
DuringSystemTest,theentiresystemistemporarilyoffͲlineandnoRFisbeingtransmitted.
•‹‰†‹”‘™•‡”ƒ†Ž‘‰‹–‘–Š‡ƒ‹ —„Ǥ
Ž‹ SYSTEM CONFIGURATIONǤ
Ž‹ SET DATE/TIMEƒ†‡–‡”–Š‡ —””‡–†ƒ–‡ƒ†–‹‡Ǥ
Ž‹ SET DATE/TIMEǤ
‘ŽŽ‘™–Š‡‹•–”— –‹‘•–‘‡˜‡–—ƒŽŽ›”‡„‘‘––Š‡•›•–‡–‘•‡––Š‡†ƒ–‡ƒ†–‹‡Ǥ
•‹‰†‹”‘™•‡”ǡŽ‘‰‹ƒ† Ž‹ SYSTEM CONFIGURATIONǤ
Ž‹ INSTALL SYSTEMǤ
‡––Š‡‡™ƒ‹ —„’ƒ”ƒ‡–‡”•ˆ”‘–Š‡‘Ž†ƒ‹ —„ƒ† Ž‹ INSTALL SYSTEM ȋ–Šƒ–‹•ǡ
—’Ž‹ƒ††‘™Ž‹‰ƒ‹ǡ•›•–‡Žƒ„‡Ž•ǡƒ†•‘‘ȌǤ
‘ŽŽ‘™–Š‡‹•–”— –‹‘•–‘’‡”ˆ‘”ƒ›•–‡‡•–Ǥ
Ž‹ SYSTEM CONFIGURATIONƒ† Ž‹ ‘SETUP NETWORK CONNECTION OR MODEM CONNECTION‹ˆ–Š‡
ƒ‹ —„Šƒ•‡–™‘”‘”‘†‡‡“—‹’‡– ‘‡ –‡†–‘‹–Ǥ
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Page 179
Š 2013 TE Connectivity Ltd.
Replacing Fusion Wideband Components
3 ChecktheLEDsontheNewMainHub
•
•
•
Š‡••Š‘—Ž†„Ž‹–Š”‘—‰ŠƒͷǦ•‡ ‘†–‡•–‘’‘™‡”—’Ǥ
– ˆ–Š‡•†‘‘–„Ž‹‘’‘™‡”—’ǡ”‡’Žƒ ‡–Š‡ƒ‹ —„Ǥ
– ˆ–Š‡•†‘‘–‹ŽŽ—‹ƒ–‡ƒ–ƒŽŽǡƒ‡•—”‡–Š‡’‘™‡” ƒ„Ž‡‹• ‘‡ –‡†Ǥ
‘”‡ƒ Šˆ‹„‡”‘’–‹ ’‘”––Šƒ–Šƒ•ƒ ‘‡ –‡†š’ƒ•‹‘ —„ǡ™Š‹ ŠŠƒ•„‡‡’”‘‰”ƒ‡†
™‹–Šƒ„ƒ†ǡ–Š‡PORT•Š‘—Ž†„‡‰”‡‡Ǥ
‡ˆ‡”–‘Dz”‘—„Ž‡•Š‘‘–‹‰•‹‰•dz‘’ƒ‰‡ͳͺ͸ˆ‘”‘”‡•–ƒ–‡•Ǥ
NOTE:
If there is no communication between the Main Hub and the Expansion Hubs, use the
AdminBrowsertoisolatesystemproblems.
Page 180
Š 2013 TE Connectivity Ltd
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
MAINTENANCE,TROUBLESHOOTING,ANDTECHNICAL
ASSISTANCE
Topics
Page
Service................................................................................................................................................................................. 182
Maintenance ....................................................................................................................................................................... 183
CleaningtheFiberPorts .........................................................................................................................................................183
Considerations................................................................................................................................................................183
UsingCompressedAir.....................................................................................................................................................183
UsingIsopropylAlcohol .................................................................................................................................................. 183
Troubleshooting .................................................................................................................................................................. 184
TroubleshootingUsingAdminBrowser...................................................................................................................................185
SystemTroubleshooting.................................................................................................................................................185
TroubleshootingRecommendations ..............................................................................................................................185
Fault/Warning/StatusIndications ..................................................................................................................................186
TroubleshootingUsingLEDs ...................................................................................................................................................186
TroubleshootingMainHubLEDsDuringNormalOperation ..........................................................................................186
TroubleshootingExpansionHubLEDsDuringNormalOperation ..................................................................................188
TroubleshootingCATV ......................................................................................................................................................... 189
TechnicalAssistance ............................................................................................................................................................ 190
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Page 181
Š2013 TE Connectivity Ltd.
Maintenance, Troubleshooting, and Technical Assistance
SERVICE
Š‡”‡ƒ”‡‘—•‡”Ǧ•‡”˜‹ ‡ƒ„Ž‡’ƒ”–•‹ƒ›‘ˆ–Š‡ —•‹‘ ‘’‘‡–•Ǥ ƒ—Ž–›‘”ˆƒ‹Ž‡† ‘’‘‡–•
ƒ”‡ˆ—ŽŽ›”‡’Žƒ ‡ƒ„Ž‡–Š”‘—‰ŠǤŽŽ—‹–••Š‘—Ž†„‡”‡’Žƒ ‡†ƒ†”‡–—”‡†–‘–Š‡ˆƒ –‘”›ˆ‘”
•‡”˜‹ ‡‹ˆ‡‡†‡†Ǥ
Address
541 E. Trimble Road
San Jose, California
95131-1224 USA
Help Hot Line
U.S. and Canada
1-800-530-9960
All Others
+1-952-917-0761
Help Web URL
Page 182
Š 2013 TE Connectivity Ltd
http://www.te.com/WirelessSupport
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Maintenance
MAINTENANCE
‡‡’–Š‡ˆ‹„‡”’‘”–• Ž‡ƒƒ†ˆ”‡‡‘ˆ†—•–Ǥ‘‘–Š‡”’‡”‹‘†‹ ƒ‹–‡ƒ ‡‘ˆ–Š‡ —•‹‘
‡“—‹’‡–‹•”‡“—‹”‡†Ǥ
CleaningtheFiberPorts
‘— ƒ Ž‡ƒ–Š‡ —„ǯ•ˆ‹„‡”’‘”–•—•‹‰ ƒ‡† ‘’”‡••‡†ƒ‹”‘”‹•‘’”‘’›ŽƒŽ ‘Š‘Žƒ† ‘––‘
•™ƒ„•Ǥ
Considerations
•
•
ˆ›‘——•‡ ‘’”‡••‡†ƒ‹”ǣ
– Š‡ƒ‹”—•–„‡ˆ”‡‡‘ˆ†—•–ǡ™ƒ–‡”ǡƒ†‘‹ŽǤ
–
‘Ž†–Š‡ ƒŽ‡˜‡Ž†—”‹‰—•‡Ǥ
ˆ—•‹‰‹•‘’”‘’›ŽƒŽ ‘Š‘Žƒ†ˆ‘ƒǦ–‹’’‡†•™ƒ„ǣ
– •‡‘Ž›ͻͺΨ’—”‡‘”‘”‡ƒŽ ‘Š‘ŽǤ
UsingCompressedAir
‡‘˜‡–Š‡ ‘‡ –‘”ǯ•†—•– ƒ’Ǥ
’”ƒ›–Š‡ ‘’”‡••‡†ƒ‹”ƒ™ƒ›ˆ”‘–Š‡—‹–ˆ‘”ƒˆ‡™•‡ ‘†•–‘ Ž‡ƒ‘—––Š‡‘œœŽ‡ƒ†
–Š‡„Ž‘™†—•–’ƒ”–‹ Ž‡•‘—–‘ˆ‡ƒ Šˆ‹„‡”’‘”–Ǥ
UsingIsopropylAlcohol
‡‘˜‡–Š‡ ‘‡ –‘”ǯ•†—•– ƒ’Ǥ
‹’ƒʹǤͷŽ‹–Ǧˆ”‡‡ǡˆ‘ƒǦ–‹’’‡†•™ƒ„‹‹•‘’”‘’›ŽƒŽ ‘Š‘Žƒ†•Ž‘™Ž›‹•‡”––Š‡–‹’‹–‘–Š‡
‘‡ –‘”Ǥ
‡–Ž›–™‹•––Š‡•™ƒ„–‘ Ž‡ƒ–Š‡ ‘‡ –‘”Ǥ
•‡”–ƒ†”›•™ƒ„–‘†”›–Š‡ ‘‡ –‘”Ǥ
††‹–‹‘ƒŽŽ›ǡ›‘— ƒ—•‡ ‘’”‡••‡†ƒ‹”ƒˆ–‡”–Š‡ƒŽ ‘Š‘ŽŠƒ• ‘’Ž‡–‡Ž›‡˜ƒ’‘”ƒ–‡†Ǥ
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Page 183
Š 2013 TE Connectivity Ltd.
Maintenance, Troubleshooting, and Technical Assistance
TROUBLESHOOTING
NOTE:
FusionhasnouserͲserviceableparts.FaultyorfailedunitsarefullyreplaceablethroughTE;see
“Service”onpage182.
‘—” ‡•‘ˆ’‘–‡–‹ƒŽ’”‘„Ž‡•‹ Ž—†‡ǣ
•
•
•
•
•
•
•
ƒ—Ž–› ƒ„Ž‹‰Ȁ ‘‡ –‘”
ƒŽˆ— –‹‘‘ˆ‘‡‘”‘”‡ —•‹‘ ‘’‘‡–•
–‡ƒǡ„ƒ•‡•–ƒ–‹‘ǡ‘””‡’‡ƒ–‡”’”‘„Ž‡
š–‡”ƒŽ ‹–‡”ˆƒ ‡
”‹’’‡† ‹” —‹–„”‡ƒ‡”
“—‹’‡–‹•‘–‰”‘—†‡†
•‹‰ƒ–Š‡”‡– ”‘••‘˜‡” ƒ„Ž‡–Šƒ–†‘‡•‘–•—’’‘”–ˆ—ŽŽŠƒ”†™ƒ”‡Šƒ†•Šƒ‹‰™Š‡
—•‹‰†‹”‘™•‡”
NOTE:
Faultycablingisthecauseofavastmajorityofproblems.AllCATV75Ohmcableshouldbetested
to TIAͲ570ͲB specifications. The RAU will be damaged if the cable connector is not installed
properly.
‘——•–—•‡†‹”‘™•‡”ˆ‘”–”‘—„Ž‡•Š‘‘–‹‰–Š‡•›•–‡ǡ—•‡–Š‡•‘Ž›ƒ•„ƒ —’‘”ˆ‘”
‘ˆ‹”ƒ–‹‘Ǥ
ˆ›‘— ƒ‘–†‡–‡”‹‡–Š‡ ƒ—•‡‘ˆƒ’”‘„Ž‡ƒˆ–‡”ˆ‘ŽŽ‘™‹‰–Š‡”‡ ‘‡†‡†’”‘ ‡†—”‡•ǡ ƒŽŽ
–Š‡—•–‘‡”—’’‘”–‡ƒǤ ‘”‹ˆ‘”ƒ–‹‘‘Š‘™–‘ ‘–ƒ –—•ǡ•‡‡“Service”onpage182.
Ž‡ƒ•‡’”‘˜‹†‡–Š‡ˆ‘ŽŽ‘™‹‰‹ˆ‘”ƒ–‹‘ǣ
•
•
•
•
•
•
‡”‹ƒŽ—„‡”‘ˆ–Š‡—‹–
‡• ”‹’–‹‘‘ˆ–Š‡’”‘„Ž‡
•‡†‹”‘™•‡”ͳǤͲͲ–‘ƒ ‡••’‡ ‹ƒŽ ‡ƒ–—”‡•ǡ–Š‡–Š‡ ‡–‡”˜‹ ‡ ˆ‘”ƒ–‹‘™‹†‘™Ǥ
ƒ˜‡ƒ†‡ƒ‹Ž–Š‹•ˆ‹Ž‡–‘Ǥ
Šƒ–‹•–Š‡Ž‡‰–Š‘ˆ–Š‡ ƒ„Ž‡ǫŠƒ––›’‡‹•‹–ȋˆ‘”‡šƒ’Ž‡ Ǧ͸Ȍǫ
–ƒ–—•‘ˆ–Š‡•‘–Š‡—‹–
ƒ•–Š‡—‹–’‘™‡” › Ž‡†ǫ
Page 184
Š 2013 TE Connectivity Ltd
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Troubleshooting
TroubleshootingUsingAdminBrowser
•‡†‹”‘™•‡”•‘ˆ–™ƒ”‡–‘†‡–‡”‹‡–Š‡ —””‡–ˆƒ—Ž–•ƒ†™ƒ”‹‰•ˆ‘”ƒŽŽ‘ˆ–Š‡—‹–•‹
–Š‡•›•–‡Ǥ‘–”‘—„Ž‡•Š‘‘–ǡ•–ƒ”–™‹–Š–Š‡ —•‹‘ƒ‹ —„ǯ•ˆƒ—Ž–•™ƒ”‹‰•ǡ–Š‡’”‘ ‡‡†
–‘‡ƒ Š‘ˆ–Š‡š’ƒ•‹‘ —„•ǡˆ‹‹•Š‹‰™‹–Š‡ƒ Š‘ˆ–Š‡•Ǥ
NOTE:
AdminBrowserv1.00displaysevents(faults,warnings,orstatusmessages)dependingonyour
viewpreference.Tochangeyourviewpreference,referto“ViewPreference”onpage38.
SystemTroubleshooting
•‹‰†‹”‘™•‡”ǡ Ž‹ SYSTEM INFORMATIONǡ–Š‡ Ž‹ GET FAULTS, WARNINGS AND STATUSESǤŠ‹•
‰‹˜‡•–Š‡’”‡•‡–•–ƒ–—•‘ˆ–Š‡•›•–‡ǡ†‡’‡†‹‰—’‘‹‡™”‡ˆ‡”‡ ‡•ˆ‘”ƒŽŽ ‘’‘‡–•Ǥ
ƒ—Ž–•—•—ƒŽŽ›‹’ƒ –•‡”˜‹ ‡Ǣ™ƒ”‹‰•ƒ›‹’ƒ –•‡”˜‹ ‡Ǣ•–ƒ–—•‡••ƒ‰‡• ‘–ƒ‹‹ˆ‘”ƒ–‹‘
–Šƒ–•Š‘—Ž†‘–„‡‹‰‘”‡†ǡ„—–‹†‹ ƒ–‡ ‘†‹–‹‘•–Šƒ–†‘‘–‰‡‡”ƒŽŽ›‹’ƒ –•‡”˜‹ ‡Ǥ
NOTE:
Systemcommandscantakelongertoexecutecomparedtocomponentcommands.
NOTE:
This RAU icon  indicates there is fault on the RAU. This icon
device.Youcannotrequeststatusonadisconnecteddevice.
 indicates a disconnected
TroubleshootingRecommendations
‘‡ƒ –‹‘•–Šƒ–›‘— ƒ–ƒ‡ǡ†‡’‡†‹‰‘–Š‡†‡˜‹ ‡ˆƒ—Ž–‘”™ƒ”‹‰‹ Ž—†‡ǡƒ”‡ƒ•ˆ‘ŽŽ‘™•ǣ
•
•
•
•
•
ƒ”†™ƒ”‡ˆƒ—Ž–•‘š’ƒ•‹‘ —„Ǥ
– ”›•™ƒ’’‹‰ˆ‹„‡”™‹–Šƒ‘–Š‡”š’ƒ•‹‘ —„ƒ––Š‡ƒ‹ —„Ǥ
– ”› Ž‡ƒ‹‰–Š‡ˆ‹„‡”ƒ†–Š‡ˆ‹„‡”’‘”–•™‹–ŠƒŽ ‘Š‘Žˆ‘ƒ–‹’•™ƒ„ƒ† ‘’”‡••‡†ƒ‹”Ǣ
•‡‡DzŽ‡ƒ‹‰–Š‡ ‹„‡”‘”–•dz‘’ƒ‰‡ͳͺ͵Ǥ
– ‘™‡” › Ž‡–Š‡š’ƒ•‹‘ —„Ǥ
†‡”Žƒ”•ǡ Ž‹  CLEAR ALL DISCONNECTSƒ––Š‡ —•‹‘ƒ‹ —„Ǥ
‘™‡” › Ž‡–Š‡ —•‹‘ƒ‹ —„Ǥ
Šƒ”†™ƒ”‡ˆƒ—Ž–•Ǥ”›‘˜‹‰ƒ™‘”‹‰–‘–Š‡•—•’‡ –’‘”–ƒ†˜‡”‹ˆ›‹‰–Šƒ––Š‡
 ‘‡•—’Ǥ
”›‹•‘Žƒ–‹‰–Š‡•›•–‡ ‘’‘‡–•ǣ
– Š‡ –‘•‡‡‹ˆ–Š‡™Š‘Ž‡•›•–‡‹•‡ˆˆ‡ –‡†‘”ƒ’‘”–‹‘‘ˆ–Š‡•›•–‡Ǥ
– ˆ–Š‡™Š‘Ž‡•›•–‡‹•‡ˆˆ‡ –‡†ǡ†‹• ‘‡ ––Š‡•›•–‡ˆ”‘–Š‡ •‘—” ‡ƒ†•‡‡‹ˆ
–Š‡ •‘—” ‡‹•™‘”‹‰Ǥ
– ‘–‹—‡–‘‹•‘Žƒ–‡„›†‹•ƒ„Ž‹‰’‘”–‹‘•‘ˆ–Š‡•›•–‡Ǥ†‡”›•–‡‘ˆ‹‰—”ƒ–‹‘ǡ Ž‹ 
SHOW SYSTEM TREEƒ†•‡Ž‡ –ƒ ‘’‘‡–ǤŠ‡ Ž‹ SET OUT OF SERVICE/SET IN SERVICEǤ
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Page 185
Š 2013 TE Connectivity Ltd.
Maintenance, Troubleshooting, and Technical Assistance
Fault/Warning/StatusIndications
 ‡ƒŽŽ‘ˆ–Š‡—‹–•ƒ”‡’‘™‡”‡†‘ƒ†–Š‡ ƒ„Ž‡ ‘‡ –‹‘•ƒ”‡ƒ†‡ǡ–Š‡ˆƒ—Ž–•ˆ”‘‡ƒ Š—‹–
ƒ„‡”‡“—‡•–‡†—•‹‰†‹”‘™•‡”Ǥ–ƒ”–™‹–Š–Š‡ —•‹‘ƒ‹ —„ƒ†™‘”†‘™•–”‡ƒǤ
‡•‘Ž˜‡ƒŽŽˆƒ—Ž–•ˆ‹”•–ƒ†–Š‡ Š‡ –Š‡™ƒ”‹‰•Ǥƒ‡ƒ’’”‘’”‹ƒ–‡ƒ –‹‘–‘”‡•‘Ž˜‡–Š‡ˆƒ—Ž–•ǡ
ƒ•‹†‹ ƒ–‡†‹–Š‡ˆ‘ŽŽ‘™‹‰–ƒ„Ž‡•Ǥ  ƒ•‡•™Š‡”‡–Š‡”‡‹•‘”‡–Šƒ‘‡’‘••‹„Ž‡ ƒ—•‡ǡ–Š‡›ƒ”‡
Ž‹•–‡†ˆ”‘–Š‡Dz‘•–Ž‹‡Ž›dz–‘–Š‡DzŽ‡ƒ•–Ž‹‡Ž›dz ƒ—•‡Ǥ –‹‘•ƒ”‡Ž‹•–‡†‹–Š‡‘”†‡”–Šƒ––Š‡›
•Š‘—Ž†„‡’‡”ˆ‘”‡†Ǣ‘–ƒŽŽƒ –‹‘•ƒ›‡‡†–‘„‡†‘‡Ǥ
NOTE:
IfyouhavearedSTATUSLEDwithoutafaultmessage,itprobablyindicatesthattheunitislocked
out.
‡ˆ‡”–‘’’‡†‹šˆ‘”–ƒ„Ž‡• ‘–ƒ‹‹‰ ƒ—Ž–ǡƒ”‹‰ǡƒ†–ƒ–—•‡••ƒ‰‡•ƒ†–Š‡‹”
‡ƒ‹‰•Ǥ
TroubleshootingUsingLEDs
Š‡ˆ‘ŽŽ‘™‹‰–”‘—„Ž‡•Š‘‘–‹‰‰—‹†‡‹•ˆ”‘–Š‡’‡”•’‡ –‹˜‡–Šƒ–ƒŽŽ —•‹‘‡“—‹’‡–‹•
‹•–ƒŽŽ‡†ǡ–Š‡‹” ƒ„Ž‡•ƒ”‡ ‘‡ –‡†ǡƒ†–Š‡›ƒ”‡’‘™‡”‡†‘Ǣ‹–‹•ƒ••—‡†–Šƒ––Š‡•›•–‡™ƒ•
‘’‡”ƒ–‹‰‘”ƒŽŽ›„‡ˆ‘”‡–Š‡’”‘„Ž‡–‘„‡†‹ƒ‰‘•‡†‘ —””‡†Ǥ
Ž™ƒ›•—•‡†‹”‘™•‡”ǡ‹ˆ’‘••‹„Ž‡ǡ–‘–”‘—„Ž‡•Š‘‘––Š‡•›•–‡ǤŠ‡ —•‹‘ƒ‹ —„ƒ†
š’ƒ•‹‘ —„•ƒ”‡ˆ‘”„ƒ —’–”‘—„Ž‡•Š‘‘–‹‰ǤŠ‡•’”‘„ƒ„Ž›™‹ŽŽ‘–’”‘˜‹†‡
ƒ††‹–‹‘ƒŽ‹ˆ‘”ƒ–‹‘ˆ‘”–”‘—„Ž‡•Š‘‘–‹‰Ǥ
TroubleshootingMainHubLEDsDuringNormalOperation
ŽŽ‘ˆ–Š‡ƒ‹ —„ǯ•••Š‘—Ž†„‡‰”‡‡†—”‹‰‘”ƒŽ‘’‡”ƒ–‹‘Ǥ ˆƒ›•ƒ”‡”‡†ǡ‰‡–
•–ƒ–—•—•‹‰†‹”‘™•‡”–‘†‡–‡”‹‡–Š‡‡šƒ – ƒ—•‡ƒ†”‡ ‘‡†ƒ–‹‘•Ǥ
Page 186
Š 2013 TE Connectivity Ltd
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Troubleshooting
Table91. TroubleshootingMainHubPortLEDsDuringNormalOperation
During
Normal
Operation
Main Hub
Port LEDs
State
Action
Impact
Expansion
Hub Not
Connected
PORT
Red
If the Expansion Hub was disconnected
accidentally, re-connect the cables. The
LEDs should change to Green/Red
(then Green/Green, after 20 seconds, if
the Main Hub band has been
programmed).
The Expansion Hub was previously
connected, but it is not currently
connected; the Expansion Hub uplink
cable disconnected.
When the Expansion Hub is to be
removed from service permanently,
use AdminBrowser’s ‘Clear All
Disconnect Status’ command to clear
all disconnect states to no connect
states.
Expansion
Hub 
Connected
PORT
Flashing Red  Use AdminBrowser to determine the
(60 ppm)
exact cause of the Main Hub’s faults.
AdminBrowser clears all disconnects
caused by installation as part of the
clean-up process. After installation,
power cycle the Main Hub or use
AdminBrowser’s “Clear All Disconnect
Status” command.
Changes the Main Hub’s port LEDs to
Off/Off.
Lost communication with Expansion Hub;
could be Expansion Hub problem or fiber
cable problem.
The Expansion Hub communication
problems delay MH responses to
AdminBrowser commands, resulting in
command time-outs. You can disconnect
the offending Expansion Hub initially to
obtain status from the rest of the system,
then connect the Expansion Hub and
resolve the communication problem.
PORT
Red
The Expansion Hub or connected RAU
reports a fault condition; use
AdminBrowser to determine the exact
cause of the Expansion Hub and RAU’s
faults.
Degraded performance or unit may be
off-line.
Depends on fault condition.
Table92. TroubleshootingMainHubStatusLEDsDuringNormalOperation
During
Normal
Operation
Main Hub
Status LEDs
State
Action
Impact
At Any Time
main hub
status
Red
Use AdminBrowser to determine the
exact cause of the fault.
Internal Main Hub fault.
Power cycle one time. If the fault
remains, replace the Main Hub.
Use AdminBrowser to check if the Main
Hub is commanded Out-of-Service
(every Expansion Hub port status LED
will be red as well).
The Main Hub and all downstream units
are off-line.
A power cycle will not clear a
commanded Out-of-Service, you must
use AdminBrowser to clear this state.
At Any Time
main hub
status
Flashing Red
(60ppm)
Reduce input signal power.
Signal compression.
Power
Red
Replace the Main Hub.
One or more power supplies are out of
specification.
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Page 187
Š 2013 TE Connectivity Ltd.
Maintenance, Troubleshooting, and Technical Assistance
TroubleshootingExpansionHubLEDsDuringNormalOperation
•
•
ŽŽ‘ˆ–Š‡š’ƒ•‹‘ —„LINKƒ†E-HUB/RAU•–Šƒ–Šƒ˜‡• ‘‡ –‡†•Š‘—Ž†„‡
”‡‡Ȁ ”‡‡ǡ‹†‹ ƒ–‹‰–Šƒ––Š‡‹•’‘™‡”‡†‘ǡ ‘—‹ ƒ–‹‘‹•‡•–ƒ„Ž‹•Š‡†ǡƒ†
‘’‡”ƒ–‹‘‹•‘”ƒŽǤ
Š‡POWERǡ EHUB STATUSǡDL STATUSǡƒ† UL STATUS ••Š‘—Ž†ƒŽŽ„‡ ”‡‡Ǥ
Table93. TroubleshootingExpansionHubPortLEDsDuringNormalOperation
During
Normal
Operation
Expansion
Hub Port
LEDs
State
Action
Impact
RAU is not
connected
PORT
Off
If the RAU was disconnected
accidentally, re-connect the CATV
cable. The Expansion Hub’s port LEDs
should change to Green/Red (then
Green/Green, after 20 seconds, if the
Main Hub is connected, powered on,
and has band programmed).
The RAU was previously connected, but it
is not currently connected; the RAU cable
is disconnected.
Use AdminBrowser’s “Clear All
Disconnect Status” command if you
are permanently removing the RAU
from service. The Expansion Hub’s
port LEDs should change to Off/Off.
RAU is 
connected
PORT
Red
Disconnect/reconnect the CATV cable
to force power-on reset to the RAU. If
the port LEDs remain Red check for
the exact cause of Expansion Hub
faults using AdminBrowser.
Lost communications with the RAU. The
RAU could have powered down due to
over current; cable could have been
damaged.
PORT
Flashing
Red (60
ppm)
The RAU reports a fault condition;
check for the exact cause of
Expansion Hub and RAU faults using
AdminBrowser.
Depends on the fault condition.
PORT
Flashing
Red (60
ppm)
The Expansion Hub reports no
connection, cable shorts, or a current
port trap condition.
Expansion Hub communications with the
RAU. The Expansion Hub is at fault. The
cable could have been damaged. The cable
leads may be shorted.
Table94. TroubleshootingExpansionHubStatusLEDsDuringNormalOperation
During
Normal
Operation
Expansion
Hub Status
LEDs
State
Action
Impact
At Any Time
ul status
Red
Check uplink fiber for optical loss.
No communications between the Main Hub
and the Expansion Hub.
Power cycle Expansion Hub one time
to check uplink laser.
Uplink laser failure.
dl status
Red
Check the downlink fiber for optical
loss
No communications with the Main Hub.
E-h 
status
Red
If either the UL STATUS or the DL
STATUS are also red, see above.
Internal Expansion Hub fault (including
either of the above UL STATUS or DL
STATUS states).
Cycle power on the Expansion Hub. If
fault remains, replace the Expansion
Hub.
Page 188
Š 2013 TE Connectivity Ltd
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Troubleshooting CATV
TROUBLESHOOTINGCATV
Š‡ˆ‘ŽŽ‘™‹‰–ƒ„Ž‡•—ƒ”‹œ‡•’”‘„Ž‡•ǡƒ•”‡’‘”–‡†„›†‹”‘™•‡”‹ˆƒ ƒ„Ž‡‹• —–‘”
‹•™‹”‡†Ǥ
NOTE:
RecommendedminimumandmaximumCATVcablelengthsvarydependinguponthetypeof
CATVcableused.Referto“CableandConnectorRequirements”onpage107.
Table95. SummaryofCATVCableWiringProblems
Problem Type
Message
Loose connector, None
shorted conductor
or improper
No communication with RAUn
connection to the
shield.
Portn UL RF path loss is too high
Icon
Impact
High phase noise, degraded signal on both
Downlink and Uplink (high bit error rate)
RAU unable to communicate with Hub,
degraded performance or RAU off-line
Increased ripple in the uplink path, decreased
UL gain, or no UL gain
The DL RF path loss is too high
Increased ripple in the downlink path, RAU
off-line
RAUn over current or port short
RAU will not power on.
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Page 189
Š 2013 TE Connectivity Ltd.
Maintenance, Troubleshooting, and Technical Assistance
TECHNICALASSISTANCE
ƒŽŽ‘—”Š‡Ž’Š‘–Ž‹‡ˆ‘”–‡ Š‹ ƒŽƒ••‹•–ƒ ‡Ǣ•‡‡Dz‡”˜‹ ‡dz‘’ƒ‰‡ͳͺʹǤ
Ž‡ƒ•‡’”‘˜‹†‡›‘—”ƒ‡ǡ’Š‘‡—„‡”ǡƒ†‡Ǧƒ‹Žƒ††”‡••ǡƒŽ‘‰™‹–Š–Š‡ˆ‘ŽŽ‘™‹‰
‹ˆ‘”ƒ–‹‘Ǥ —•–‘‡”•‡”˜‹ ‡”‡’”‡•‡–ƒ–‹˜‡™‹ŽŽ ‘–ƒ –›‘—™‹–Šƒ••‹•–ƒ ‡Ǥ
•
•
•
•
•
•
•
‘’ƒ›ƒ‡
†—•‡”ƒ‡
›’‡‘ˆ•›•–‡ǡ‘†‡Ž—„‡”ǡˆ”‡“—‡ ›
’’”‘š‹ƒ–‡–‹‡‹•‡”˜‹ ‡ȋ™ƒ””ƒ–›Ȍǡ•ƒŽ‡•‘”†‡”—„‡”
‡• ”‹’–‹‘‘ˆ’”‘„Ž‡
•–ƒ–—•
†‹”‘™•‡”ˆƒ—Ž–•ǡ™ƒ”‹‰•ǡƒ†•–ƒ–—•‡••ƒ‰‡•
Page 190
Š 2013 TE Connectivity Ltd
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
APPENDIXA:CABLESANDCONNECTORS
Topics
Page
75OhmCATVCable ............................................................................................................................................................. 192
GeneralSpecifications ............................................................................................................................................................192
RecommendedCATVCableLengths.......................................................................................................................................192
ConnectorsandToolsforCableEnds .....................................................................................................................................196
FiberOpticalCables ............................................................................................................................................................. 197
CoaxialCable ....................................................................................................................................................................... 198
StandardModemCable ....................................................................................................................................................... 199
TCP/IPCrossͲOverCable ...................................................................................................................................................... 200
DBͲ9toDBͲ9NullModemCable .......................................................................................................................................... 201
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Page 191
Š2013 TE Connectivity Ltd.
Appendix A: Cables and Connectors
75OHMCATVCABLE
GeneralSpecifications
•
•
•
•
•
•
‘‡ –•–Š‡š’ƒ•‹‘ —„–‘–Š‡ȋ•Ȍ
”ƒ•‹–•—Ž–‹„ƒ†ȋ†‘™Ž‹Ȍƒ†”‡ ‡‹˜‡•ȋ—’Ž‹Ȍ •‹‰ƒŽ•
‡Ž‹˜‡”•‡Ž‡ –”‹ ƒŽ’‘™‡”–‘–Š‡•ǤŠ‡ —•‹‘ —„ǯ•˜‘Ž–ƒ‰‡‘—–’—–‹•ͷͶ
‘‹ƒŽǤ —””‡–Ž‹‹–‹‰ ‹” —‹–‹•—•‡†–‘’”‘–‡ ––Š‡ —„‹ˆ‹–”‡ƒ Š‡•‹–• —””‡–Ž‹‹–
ƒ””‹‡• ‘ˆ‹‰—”ƒ–‹‘ƒ†•–ƒ–—•‹ˆ‘”ƒ–‹‘
•‡͹ͷŠ–›’‡Ǧ  ‘‡ –‘”•™‹–Š ƒ’–‹˜‡ ‡–‡”’‹•
‡‰–Š•
–  Ǧͷͻǣ
„
Ȉ‹‹—ǣͲ‡–‡”•ȋͲˆ–ǤȌ
„
Ȉƒš‹—ǣͳͷͲ‡–‡”•ȋͶͻʹˆ–ǤȌ
–  Ǧ͸ǣ
„
Ȉ‹‹—ǣͲ‡–‡”•ȋͲˆ–ǤȌ
„
Ȉƒš‹—ǣͳ͹Ͳ‡–‡”•ȋͷͷͺˆ–ǤȌ
–  Ǧͳͳǣ
„
Ȉ‹‹—ǣͲ‡–‡”•ȋͲˆ–ǤȌ
„
Ȉƒš‹—ǣʹ͹ͷ‡–‡”•ȋͻͲʹˆ–ǤȌ
RecommendedCATVCableLengths
‡ ‘‡†‡†‹‹—ƒ†ƒš‹— ƒ„Ž‡Ž‡‰–Š•˜ƒ”›†‡’‡†‹‰—’‘™Š‹ Š
ƒ„Ž‡›‘——•‡Ǥȋ‡•—”‡–‘–‡•– ƒ„Ž‡–‡”‹ƒ–‹‘„‡ˆ‘”‡‹•–ƒŽŽ‹‰–Š‡ ƒ„Ž‡ǤȌ
•
•
•
•
•
•
•
‘ ‘’‡ ƒ„Ž‡‘”‡“—‹˜ƒŽ‡–‹•”‡“—‹”‡†ǣ
‘ ‘’‡ʹͲ͸ͷͷˆ‘” ǦͷͻǤŠ‹• ƒ„Ž‡‹•‹ŽŽ—•–”ƒ–‡†‹ ‹‰—”‡ǦͳǤ
‘ ‘’‡ʹʹ͹ͻˆ‘” Ǧ͸ǤŠ‹• ƒ„Ž‡‹•‹ŽŽ—•–”ƒ–‡†‹ ‹‰—”‡ǦʹǤ
‘ ‘’‡ʹʹͻ͵ˆ‘” ǦͳͳǤŠ‹• ƒ„Ž‡‹•‹ŽŽ—•–”ƒ–‡†‹ ‹‰—”‡Ǧ͵Ǥ
‘ ‘’‡ʹͲ͸ͷˆ‘” Ǧͷͻ
‘ ‘’‡ʹʹ͹ͻˆ‘” Ǧ͸
‘ ‘’‡ʹʹͻ͵ˆ‘” Ǧͳͳ
Page 192
Š 2013 TE Connectivity Ltd
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
75 Ohm CATV Cable
Figure59.CommScope 2065V for RG-59
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Page 193
Š 2013 TE Connectivity Ltd.
Appendix A: Cables and Connectors
Figure60.CommScope 2079V for RG-6
Page 194
Š 2013 TE Connectivity Ltd
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
75 Ohm CATV Cable
Figure61.CommScope 2293K for RG-11
NOTE:
TE requires solid copper center conductor CATV cable for proper DC voltage to the RAU and
maximumdistances.
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Page 195
Š 2013 TE Connectivity Ltd.
Appendix A: Cables and Connectors
ConnectorsandToolsforCableEnds
•‡–Š‡ˆ‘ŽŽ‘™‹‰ ‘‡ –‘”•ƒ†–‘‘Ž•–‘’”‡’ƒ”‡–Š‡ ƒ„Ž‡‡†•ǣ
•
•
•
•
•
•
•
•
•
‘ ‘’‡ ƒ„Ž‡’ƒ”–—„‡”ǣʹͲ͸ͷ
ƒƒ”‡’ƒ”–—„‡”ǣ  ‘‡ –‘” ǦͶ
”‹’‘‘ŽǦͳǡ”‹’‹‡ǦͶǡƒ„Ž‡–”‹’’”‡’ƒ”ƒ–‹‘–‘‘ŽͳͲͲ
‘ ‘’‡ ƒ„Ž‡’ƒ”–—„‡”ǣʹʹ͹ͻ
ƒƒ”‡’ƒ”–—„‡”ǣ  ‘‡ –‘” Ǧͷͷ
”‹’‘‘ŽǦͳǡ”‹’‹‡Ǧ͵ͷǡƒ„Ž‡–”‹’’”‡’ƒ”ƒ–‹‘–‘‘ŽͳͲͲ
‘ ‘’‡ ƒ„Ž‡’ƒ”–—„‡”ǣʹʹͻ͵
ƒƒ”‡’ƒ”–—„‡”ǣ  ‘‡ –‘” Ǧ͹ͳ
”‹’‘‘ŽǦͳǡ”‹’‹‡Ǧ͹ǡƒ„Ž‡–”‹’’”‡’ƒ”ƒ–‹‘–‘‘ŽͳͲͲ
ˆ–Š‡ƒš‹—†‹•–ƒ ‡‹•‘–”‡“—‹”‡†ǡ–Š‡ ‘’’‡”Ǧ Žƒ†‘˜‡”•–‡‡ŽǦ ‡–‡” ‘†— –‘” ƒ„Ž‡ƒ›
„‡—•‡†–‘”‡†— ‡ ƒ„Ž‡ ‘•–•Ǥ
ƒ„Ž‡ͻ͸•Š‘™‘ ‘’‡ ƒ„Ž‡ Š‘‹ ‡•‘ˆ’Ž‡—ǡ‘Ǧ’Ž‡—ǡ•‘Ž‹† ‘’’‡” ‘†— –‘”ǡƒ†
‘’’‡”Ǧ Žƒ†‘˜‡”Ǧ•–‡‡Ž ‘†— –‘” ƒ„Ž‡™‹–Š–Š‡‹”’ƒ”–—„‡”•ƒ†ƒš‹—†‹•–ƒ ‡•Ǥ
Table96. SystemGain(Loss)RelativetoCATVCableLength
Cable
Type
CommScope Plenum
Part Number Rated
Solid Copper
Conductor
RG-59
2065V
Yes
2022V
Yes
5572R
No
5565
No
2279V
Yes
2275V
Yes
5726
No
5765
No
2293K
Yes
2285K
Yes
5913
No
RG-6
RG-11
Copper Clad
Conductor
Zero-loss RF
Maximum
Length
(meters)
Distance
Where RF
is 10dB
Below Input
RF
(meters)
130
180
100
100*
95
95*
130
180
140
190
140
150*
140
140*
140
190
235
320
235
300*
235
300*
* Exceeding the distance of copper-clad cable will result in the attached RAU becoming non-functional.
If the distance of a cable run is at its maximum and is of concern, TE recommends the use of solid
copper cable to ensure successful operation.
Page 196
Š 2013 TE Connectivity Ltd
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Fiber Optical Cables
FIBEROPTICALCABLES
•
•
•
•
•
•
‘‡ –•–Š‡ƒ‹ —„–‘š’ƒ•‹‘ —„ȋ•Ȍ
”ƒ•‹–•ȋ†‘™Ž‹Ȍƒ†”‡ ‡‹˜‡•ȋ—’Ž‹Ȍ‘’–‹ ƒŽ•‹‰ƒŽ•
ƒ””‹‡• ‘ˆ‹‰—”ƒ–‹‘ƒ†•–ƒ–—•‹ˆ‘”ƒ–‹‘
•‡‹†—•–”›Ǧ•–ƒ†ƒ”†͸ʹǤͷρȀͳʹͷρ ‘”‘”‹‰ Ǧʹͺˆ‹„‡”ǡ‘”‡“—‹˜ƒŽ‡–Ǥ
Ȁȋƒ‰Ž‡Ǧ’‘Ž‹•Š‡†Ȍ ‘‡ –‘”•ƒ”‡”‡“—‹”‡†–Š”‘—‰Š‘—––Š‡ˆ‹„‡”‡–™‘”
ȋ’‘”–Ǧ–‘Ǧ’‘”–Ȍǡ‹ Ž—†‹‰ˆ‹„‡”†‹•–”‹„—–‹‘’ƒ‡Ž•
‹•–ƒ ‡•ǣ
– —Ž–‹Ǧ‘†‡ ‹„‡”ǣ—’–‘ͷͲͲȋͳǡ͸ͶͲˆ–ȌȂ͵†‘’–‹ ƒŽŽ‘••ƒš‹—
– ‹‰Ž‡Ǧ‘†‡ ‹„‡”ǣ—’–‘͸ȋͳͻǡ͸ͺͷˆ–ȌȂ͵†‘’–‹ ƒŽŽ‘••ƒš‹—
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Page 197
Š 2013 TE Connectivity Ltd.
Appendix A: Cables and Connectors
COAXIALCABLE
•
•
‘‡ –•ƒ —•‹‘ —„–‘ƒ”‡’‡ƒ–‡”‘”„ƒ•‡•–ƒ–‹‘ȋǦ–›’‡ ‘‡ –‘”•Ȍ
‘‡ –•ƒ–‘ƒ’ƒ••‹˜‡ƒ–‡ƒȋǦ–›’‡ ‘‡ –‘”•Ȍ
Page 198
Š 2013 TE Connectivity Ltd
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Standard Modem Cable
STANDARDMODEMCABLE
Š‹• ƒ„Ž‡ȋͶͲʹͺǦͳͲȌ ‘‡ –•ƒ‘†‡–‘–Š‡ —•‹‘ —„ǯ•ˆ”‘–’ƒ‡Ž•‡”‹ƒŽ’‘”–Ǥ
DB-9 Connector
Pin
DB-25 Connector
Pin
20
22
Figure62.Standard Modem Cable Pinouts
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Page 199
Š 2013 TE Connectivity Ltd.
Appendix A: Cables and Connectors
TCP/IPCROSSͲOVERCABLE
Ȁ  ”‘••Ǧ‘˜‡” ƒ„Ž‡ȋͶͲ͸ͻǦȌ‹•—•‡†–‘ ‘‡ –ƒ•–ƒ†ƒ”†„”‘™•‡”–‘–Š‡
†‹”‘™•‡”™‹–Šƒ —•‹‘ —„Ǥ ƒ„Ž‡‹•‹ Ž—†‡†™‹–Š–Š‡ —•‹‘ —„ǤŠ‡’‹‘—–•ˆ‘”–Š‹•
ƒ„Ž‡ƒ”‡‹ŽŽ—•–”ƒ–‡†‹ ‹‰—”‡͸͵Ǥ
Figure63.Wiring Map for TCP/IP Cable
Page 200
Š 2013 TE Connectivity Ltd
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
DB-9 to DB-9 Null Modem Cable
DBͲ9TODBͲ9NULLMODEMCABLE
•‡ƒǦͻˆ‡ƒŽ‡–‘Ǧͻˆ‡ƒŽ‡—ŽŽ‘†‡ ƒ„Ž‡–‘ ‘‡ ––Š‡ ”ƒˆ–’‡”•‘ǯ•Ȁƒ’–‘’–‘
–Š‡Ǧʹ͵ʹ’‘”–‘–Š‡ˆ”‘–‘ˆ–Š‡ —•‹‘ —„ˆ‘” ƒ††”‡•• ‘ˆ‹‰—”ƒ–‹‘Ǥƒ„Ž‡ͻ͹Ž‹•–•–Š‡
ƒ„Ž‡’‹‘—–ƒ† ‹‰—”‡͸Ͷ•Š‘™•ƒ†‹ƒ‰”ƒ‘ˆ‹–•™‹”‹‰Ǥ
Table97. DBͲ9FemaletoDBͲ9FemaleNullModemCablePinout
From
Signal
To
Signal
P1-4
DTR
P2-6, P2-1
DSR, DCD
P1-6
DSR
P1-1, P2-4
DCD, DTR
P1-3
TXD
P2-2
RXD
P1-2
RXD
P2-3
TXD
P1-5
GND
P2-5
GND
P1-7
RTS
P2-8
CTS
P1-8
CTS
P2-7
RTS
P1-9
N/C
N/C
N/C
DB-9 Connector
Pin
DB-9 Connector
Pin
Note that for each DB-9 connector, pins 1 and 6 are tied
together and sent to pin 4 of the opposite connector,
providing the required handshake signals.
Figure64.DB-9 Female to DB-9 Female Null Modem Cable Diagram
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Page 201
Š 2013 TE Connectivity Ltd.
Appendix A: Cables and Connectors
Page 202
Š 2013 TE Connectivity Ltd
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
APPENDIXB:COMPLIANCE
Topics
Page
FusionWidebandSystemApprovalStatus ........................................................................................................................... 204
700MHzLTEProducts............................................................................................................................................................204
800SMR/iDENProducts .........................................................................................................................................................204
850CellularProducts..............................................................................................................................................................204
1800DCSProducts .................................................................................................................................................................204
1900PCSProducts..................................................................................................................................................................204
2100UMTSProducts ..............................................................................................................................................................205
1700/2100AWSProducts ......................................................................................................................................................205
2500WiMAXProducts............................................................................................................................................................205
2600MHzLTEProducts..........................................................................................................................................................205
InterReachFusionWidebandMainHubandExpansionHub.................................................................................................206
HumanExposuretoRF......................................................................................................................................................... 207
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Page 203
Š2013 TE Connectivity Ltd.
Appendix B: Compliance
FUSIONWIDEBANDSYSTEMAPPROVALSTATUS
–‡”‡ƒ Š —•‹‘‹†‡„ƒ†Šƒ•„‡‡ƒ’’”‘˜‡†ƒ••Š‘™„‡Ž‘™Ǥ
700MHzLTEProducts
•
•
•
ƒˆ‡–›ǣǡǡ Š‡‡ ‡”–‹ˆ‹ ƒ–‡–‘ ͸ͲͻͷͲǡ͵”††‹–‹‘ǡƒ† ͸ͲͻͷͲǦͳǡͳ•–†‹–‹‘ǡ
™‹–ŠƒŽŽƒ–‹‘ƒŽ†‡˜‹ƒ–‹‘•Ǥ
ǣ ’ƒ”–ͳͷ Žƒ••
ƒ†‹‘ǣ ’ƒ”–ʹ͹
800SMR/iDENProducts
•
•
•
ƒˆ‡–›ǣǡǡ Š‡‡ ‡”–‹ˆ‹ ƒ–‡–‘ ͸ͲͻͷͲǡ͵”††‹–‹‘ǡƒ† ͸ͲͻͷͲǦͳǡͳ•–†‹–‹‘ǡ
™‹–ŠƒŽŽƒ–‹‘ƒŽ†‡˜‹ƒ–‹‘•Ǥ
ǣ ’ƒ”–ͳͷ Žƒ••
ƒ†‹‘ǣ ’ƒ”–ͻͲ
850CellularProducts
•
•
•
ƒˆ‡–›ǣǡǡ Š‡‡ ‡”–‹ˆ‹ ƒ–‡–‘ ͸ͲͻͷͲǡ͵”††‹–‹‘ǡƒ† ͸ͲͻͷͲǦͳǡͳ•–†‹–‹‘ǡ
™‹–ŠƒŽŽƒ–‹‘ƒŽ†‡˜‹ƒ–‹‘•Ǥ
ǣ ’ƒ”–ͳͷ Žƒ••
ƒ†‹‘ǣ ’ƒ”–ʹʹ
1800DCSProducts
•
•
•
ƒˆ‡–›ǣǡǡ Š‡‡ ‡”–‹ˆ‹ ƒ–‡–‘ ͸ͲͻͷͲǡ͵”††‹–‹‘ǡƒ† ͸ͲͻͷͲǦͳǡͳ•–†‹–‹‘ǡ
™‹–ŠƒŽŽƒ–‹‘ƒŽ†‡˜‹ƒ–‹‘•Ǥ
ǣ;Ͳͳ͜ͺ͝njͺͳǤʹǤͳ
ƒ†‹‘ǣ͵ͲͲ͸ͲͻǦͶͻǤʹǤͳ
1900PCSProducts
•
•
•
ƒˆ‡–›ǣǡǡ Š‡‡ ‡”–‹ˆ‹ ƒ–‡–‘ ͸ͲͻͷͲǡ͵”††‹–‹‘ǡƒ† ͸ͲͻͷͲǦͳǡͳ•–†‹–‹‘ǡ
™‹–ŠƒŽŽƒ–‹‘ƒŽ†‡˜‹ƒ–‹‘•Ǥ
ǣ ’ƒ”–ͳͷ Žƒ••
ƒ†‹‘ǣ ’ƒ”–ʹͶ
Page 204
Š 2013 TE Connectivity Ltd
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Fusion Wideband System Approval Status
2100UMTSProducts
•
•
•
ƒˆ‡–›ǣǡǡ Š‡‡ ‡”–‹ˆ‹ ƒ–‡–‘ ͸ͲͻͷͲǡ͵”††‹–‹‘ǡƒ† ͸ͲͻͷͲǦͳǡͳ•–†‹–‹‘ǡ
™‹–ŠƒŽŽƒ–‹‘ƒŽ†‡˜‹ƒ–‹‘•Ǥ
ǣ;Ͳͳ͜ͺ͝njʹ;ͳǤʹǤͳ
ƒ†‹‘ǣ͵ͲͳͻͲͺǦͳͳʹǤ͵Ǥͳ
1700/2100AWSProducts
•
•
•
ƒˆ‡–›ǣǡǡ Š‡‡ ‡”–‹ˆ‹ ƒ–‡–‘ ͸ͲͻͷͲǡ͵”††‹–‹‘ǡƒ† ͸ͲͻͷͲǦͳǡͳ•–†‹–‹‘ǡ
™‹–ŠƒŽŽƒ–‹‘ƒŽ†‡˜‹ƒ–‹‘•Ǥ
ǣ ’ƒ”–ͳͷ Žƒ••
ƒ†‹‘ǣ ’ƒ”–ʹ͹
2500WiMAXProducts
•
•
•
ƒˆ‡–›ǣǡǡ Š‡‡ ‡”–‹ˆ‹ ƒ–‡–‘ ͸ͲͻͷͲǡ͵”††‹–‹‘ǡƒ† ͸ͲͻͷͲǦͳǡͳ•–†‹–‹‘ǡ
™‹–ŠƒŽŽƒ–‹‘ƒŽ†‡˜‹ƒ–‹‘•Ǥ
ǣ ’ƒ”–ͳͷ Žƒ••
ƒ†‹‘ǣ ’ƒ”–ʹ͹
2600MHzLTEProducts
•
•
•
ƒˆ‡–›ǣǡǡ Š‡‡ ‡”–‹ˆ‹ ƒ–‡–‘ ͸ͲͻͷͲǡ͵”††‹–‹‘ǡƒ† ͸ͲͻͷͲǦͳǡͳ•–†‹–‹‘ǡ
™‹–ŠƒŽŽƒ–‹‘ƒŽ†‡˜‹ƒ–‹‘•Ǥ
ǣ;Ͳͳ͜ͺ͝njʹ;ͳǤʹǤͳ
ƒ†‹‘ǣ͵ͲͳͻͲͺǦͳͳʹǤ͵Ǥͳ
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Page 205
Š 2013 TE Connectivity Ltd.
Appendix B: Compliance
InterReachFusionWidebandMainHubandExpansionHub
•
•
•
ƒˆ‡–›ǣǡǡ Š‡‡ ‡”–‹ˆ‹ ƒ–‡–‘ ͸ͲͻͷͲǦͳǡ ‹”•–†‹–‹‘ǡ™‹–ŠƒŽŽƒ–‹‘ƒŽ
†‡˜‹ƒ–‹‘•Ǥ
ÇŁ Í´Í´
ÇŁ Í´Íś
NOTE:
ForCanadiancustomers,theManufacturer’sratedoutputpower1ofthisequipmentisforsingle
carrieroperation.Forsituationswhenmultiplecarriersignalsarepresent,theratingwouldhave
to be reduced by 3.5 dB, especially where the output signal is reͲradiated and can cause
interferencetoadjacentbandusers.Thispowerreductionistobebymeansofinputpoweror
gainreductionandnotbyanattenuatorattheoutputofthedevice.
NOTE:
ThisdevicecomplieswithPart15oftheFCCRules.Operationissubjecttothefollowingtwo
conditions:(1)thisdevicemaynotcauseharmfulinterference,and(2)thisdevicemustaccept
anyinterferencereceived,includinginterferencethatmaycauseundesiredoperation.
NOTE:
ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassAdigitaldevice,
pursuanttoPart15oftheFCCRules.Theselimitsaredesignedtoprovidereasonableprotection
against harmful interference when the equipment is operated in a commercial environment.
Thisequipmentgenerates,uses,andcanradiateradiofrequencyenergyand,ifnotinstalledand
used in accordance with the instruction manual, may cause harmful interference to radio
communications.
Š‹•‡“—‹’‡– ‘’Ž‹‡•™‹–Š–Š‡ ”ƒ†‹ƒ–‹‘‡š’‘•—”‡Ž‹‹–•ˆ‘”‰‡‡”ƒŽ
’‘’—Žƒ–‹‘Ȁ— ‘–”‘ŽŽ‡†‡š’‘•—”‡‡˜‹”‘‡–•Ǥ
Šƒ‰‡•‘”‘†‹ˆ‹ ƒ–‹‘•‘–ƒ’’”‘˜‡†ƒ†’‡”ˆ‘”‡†„›ƒ›˜‘‹†–Š‡—•‡”ǯ•ƒ—–Š‘”‹–›–‘
‘’‡”ƒ–‡–Š‡‡“—‹’‡–Ǥ
WARNING.Š‹•‹•NOTƒCONSUMER†‡˜‹ ‡Ǥ –‹•†‡•‹‰‡†ˆ‘”‹•–ƒŽŽƒ–‹‘„›FCC
LICENSEESƒ†QUALIFIEDINSTALLERSǤ‘—MUSTŠƒ˜‡ƒFCCLicense‘”‡š’”‡••
‘•‡–‘ˆƒ Ž‹ ‡•‡‡–‘‘’‡”ƒ–‡–Š‹•†‡˜‹ ‡Ǥƒ—–Š‘”‹œ‡†—•‡ƒ›”‡•—Ž–‹•‹‰‹ˆ‹ ƒ–
ˆ‘”ˆ‡‹–—”‡’‡ƒŽ–‹‡•ǡ‹ Ž—†‹‰’‡ƒŽ–‹‡•‹‡š ‡••‘ˆ̈́ͳͲͲǡͲͲͲˆ‘”‡ƒ Š ‘–‹—‹‰˜‹‘Žƒ–‹‘Ǥ
Part 90 Signal Boosters
WARNING.Š‹•‹•NOTƒCONSUMER†‡˜‹ ‡Ǥ –‹•†‡•‹‰‡†ˆ‘”‹•–ƒŽŽƒ–‹‘„›FCC
LICENSEESƒ†QUALIFIEDINSTALLERSǤ‘—MUSTŠƒ˜‡ƒFCCLicense‘”‡š’”‡••
‘•‡–‘ˆƒ Ž‹ ‡•‡‡–‘‘’‡”ƒ–‡–Š‹•†‡˜‹ ‡Ǥ‘—”‡‰‹•–‡”Žƒ•••‹‰ƒŽ„‘‘•–‡”•
ȋƒ•†‡ˆ‹‡†‹Ͷ͹ ͻͲǤʹͳͻȌ‘Ž‹‡ƒ–www.fcc.gov/signalǦboosters/registrationǤ
ƒ—–Š‘”‹œ‡†—•‡ƒ›”‡•—Ž–‹•‹‰‹ˆ‹ ƒ–ˆ‘”ˆ‡‹–—”‡’‡ƒŽ–‹‡•ǡ‹ Ž—†‹‰’‡ƒŽ–‹‡•‹‡š ‡••
‘ˆ̈́ͳͲͲǡͲͲͲˆ‘”‡ƒ Š ‘–‹—‹‰˜‹‘Žƒ–‹‘Ǥ
1 “Manufacturer’s rated output power” refers to Fusion Wideband’s downlink P1dB. The power per carrier tables take
into account this power reduction for multiple carriers.
Page 206
Š 2013 TE Connectivity Ltd
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Human Exposure to RF
HUMANEXPOSURETORF
Š‡ǤǤ ‡†‡”ƒŽ‘—‹ ƒ–‹‘•‘‹••‹‘ȋ ȌŠƒ•†‡˜‡Ž‘’‡†‰—‹†‡Ž‹‡•ˆ‘”‡˜ƒŽ—ƒ–‹‘‘ˆ
Š—ƒ‡š’‘•—”‡–‘ ‡‹••‹‘•ǤŠ‡‰—‹†‡Ž‹‡•‹ ‘”’‘”ƒ–‡Ž‹‹–•ˆ‘”ƒš‹—‡”‹••‹„Ž‡
š’‘•—”‡ȋȌˆ‘”’‘™‡”†‡•‹–›‘ˆ–”ƒ•‹––‡”•‘’‡”ƒ–‹‰ƒ–ˆ”‡“—‡ ‹‡•„‡–™‡‡͵ͲͲ œƒ†
ͳͲͲ œǤ‹‹–•Šƒ˜‡„‡‡•‡–ˆ‘”’‘”–ƒ„Ž‡ǡ‘„‹Ž‡ǡƒ†ˆ‹š‡†‡“—‹’‡–Ǥ’”‘†— –•ˆƒŽŽ‹–Š‡
ƒ–‡‰‘”›‘ˆˆ‹š‡†‡“—‹’‡–Ǣ’”‘†— –•‹–‡†‡†–‘„‡’‡”ƒ‡–Ž›•‡ —”‡†ƒ†‡š’‘•—”‡•ƒ”‡
‡˜ƒŽ—ƒ–‡†ˆ‘”†‹•–ƒ ‡•‰”‡ƒ–‡”–ŠƒʹͲ ȋ͹͹ȀͺdzȌǤ‘”–ƒ„Ž‡†‡˜‹ ‡•ˆƒŽŽ‹–‘‡š’‘•—”‡•‘ˆŽ‡••
–ŠƒʹͲ ǡƒ”‡‡˜ƒŽ—ƒ–‹‘•ƒ”‡—•‡†Ǥ
–‡ƒ‰ƒ‹‹•”‡•–”‹ –‡†–‘ͳǤͷȋʹǤͶͻ Ȍ‹‘”†‡”–‘•ƒ–‹•ˆ› ‡š’‘•—”‡ ‘’Ž‹ƒ ‡
”‡“—‹”‡‡–•Ǥ ˆŠ‹‰Š‡”–ŠƒͳǤͷǡ”‘—–‹‡‡˜ƒŽ—ƒ–‹‘‹•‡‡†‡†ǤŠ‡ƒ–‡ƒ••Š‘—Ž†
„‡‹•–ƒŽŽ‡†–‘’”‘˜‹†‡ƒ–Ž‡ƒ•–ʹͲ ˆ”‘ƒŽŽ’‡”•‘•–‘•ƒ–‹•ˆ›”‡“—‹”‡‡–•‘ˆ ƒ”–ʹǡ
ʹǤͳͲ͝ͳǤ
ƒ•‹ ‡˜ƒŽ—ƒ–‹‘‹•’‡”ˆ‘”‡†„›–ƒ‹‰–Š‡ƒš‹—’‘™‡”‘—–’—–‘ˆ–Š‡‡“—‹’‡–ǡ–Š‡
‰ƒ‹‘ˆ–Š‡ƒ–‡ƒ–‘„‡—•‡†ǡƒ††‹•–ƒ ‡ˆ”‘–Š‡ƒ–‡ƒǡ”‡ˆ‡”‡ ‡†‹ —ŽŽ‡–‹͸ͷ
DzEvaluationCompliancewithFCCGuidelinesforHumanExposuretoRadioFrequencyforElectric
FieldsdzǤ
’”‘†— –•–”ƒ•‹–™‡ŽŽ„‡Ž‘™–Š‡ ’‘™‡”†‡•‹–›Ž‹‹–•Ǥ †‡ˆ‹‡•’‘™‡”‘—–’—–Ž‹‹–•
ƒ–ʹͲ †‹•–ƒ ‡ˆ‘”˜ƒ”‹‘—•ˆ”‡“—‡ ›”ƒ‰‡•ǣ
•
•
˜‡”͵ͲͲ œ–‘ͳǤͷ
„‘˜‡ͳǤͷ
œ–Š‡Ž‹‹–‹•†‡–‡”‹‡†„›ˆ”‡“—‡ ›ȀͳͷͲͲ
œ–Š‡Ž‹‹–‹•ͳȀ ʹ
Š‡„ƒ•‹ ‡“—ƒ–‹‘ˆ‘”†‡–‡”‹‹‰’‘™‡”†‡•‹–›‹•ǣ
S = PG / 4SR2
Š‡”‡S‹•’‘™‡”†‡•‹–›‹Ȁ ʹ
PGǡ–Š‡–”ƒ•‹––‡†’‘™‡”ˆ”‘–Š‡ƒ–‡ƒ‹†‡–‹ˆ‹‡†ƒ• ȋ“—‹˜ƒŽ‡– •‘–”‘’‹ ƒŽŽ›ƒ†‹ƒ–‡†
‘™‡”Ȍǡ‹•–Š‡’”‘†— –‘ˆ’‘™‡”‘—–’—–‘ˆ†‡˜‹ ‡ƒ†ƒ–‡ƒ‰ƒ‹ǡ‹Ǥ
R‹•–Š‡†‹•–ƒ ‡‘ˆ‹–‡”‡•–ˆ”‘–Š‡ƒ–‡ƒǤ
›’‹ ƒŽ •–ƒŽŽƒ–‹‘šƒ’Ž‡ǣ
••—‹‰ƒƒ–‡ƒ‹•’Žƒ ‡†‘ƒͳͲˆ‘‘– ‡‹Ž‹‰ǡˆ‘”ƒ’‡”•‘͸ˆ‡‡––ƒŽŽǡ–Š‡†‹•–ƒ ‡ˆ”‘
ƒ–‡ƒ–‘„‘†›‹•Ͷˆ‡‡–ȋͳͳʹ ǤȌǤ
‘”ƒͳͻͲͲ”‡‘–‡—‹–ǡ–Š‡ƒš‹—’‘™‡”‘—–’—–ǡƒ ‘”†‹‰–‘–Š‡’‘™‡”–ƒ„Ž‡‹
‡ –‹‘͸Ǥ͵ƒš‹——–’—–‘™‡”’‡”ƒ””‹‡”͸ǦͶǡ‹•ͳ͸Ǥͷ†Ǥ
••—‹‰ƒ͹†‹ƒ–‡ƒ‹•—•‡†ǡ ‹–Š‡‡“—ƒ–‹‘‹•‡“—ƒŽ–‘ʹ͵Ǥͷ†ȋʹʹͶȌ Ǥ
•‹‰α ȀͶSʹ
αʹʹͶȀȋͶš͵ǤͳͶȌšȋͳʹʹȌʹαͲǤͲͲͳȀ ʹ
Ž•‘ǡƒ••—‹‰ƒ‹‹—†‹•–ƒ ‡‘ˆʹͲ ƒ ‘”†‹‰–‘ ”‡‰—Žƒ–‹‘•ǣ
αʹʹͶȀȋͶš͵ǤͳͶȌšȋʹͲȌʹαͲǤͲͶȀ ʹ
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Page 207
Š 2013 TE Connectivity Ltd.
Appendix B: Compliance
Page 208
Š 2013 TE Connectivity Ltd
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
APPENDIXC:FAULTS,WARNINGS,STATUSTABLESFOR
FUSION,FUSIONWIDEBAND,FUSIONSINGLESTAR
Topics
Page
FaultsReportedbyMainHubs ............................................................................................................................................. 210
FaultsReportedforSystemCPU........................................................................................................................................... 213
FaultsforExpansionHubs .................................................................................................................................................... 214
FaultsforRAUs .................................................................................................................................................................... 216
MessagesforMainHubs...................................................................................................................................................... 217
WarningMessages .................................................................................................................................................................217
StatusMessages .....................................................................................................................................................................217
MessagesforSystemCPUs................................................................................................................................................... 222
MessagesforExpansionHubs .............................................................................................................................................. 223
MessagesforRAUs .............................................................................................................................................................. 226
Š‡ˆ‘ŽŽ‘™‹‰–ƒ„Ž‡• ‘–ƒ‹‡••ƒ‰‡•ˆ‘”ƒŽŽ˜‡”•‹‘•‘ˆˆ‹”™ƒ”‡ǡ„—–ƒŽŽ‡••ƒ‰‡•ƒ”‡‘–
†‹•’Žƒ›‡†„›ƒ‰‹˜‡ˆ‹”™ƒ”‡˜‡”•‹‘Ǥ
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Page 209
Š2013 TE Connectivity Ltd.
Appendix C: Faults, Warnings, Status Tables for Fusion, Fusion Wideband, Fusion SingleStar
FAULTSREPORTEDBYMAINHUBS
ƒ—Ž–•‹†‹ ƒ–‡•‡”˜‹ ‡Ǧ‹’ƒ –‹‰ ‘†‹–‹‘•ƒ†•Š‘—Ž†„‡‰‹˜‡‹‡†‹ƒ–‡ƒ––‡–‹‘Ǥ
 ‡ƒŽŽ‘ˆ–Š‡—‹–•ƒ”‡’‘™‡”‡†‘ƒ†–Š‡ ƒ„Ž‡ ‘‡ –‹‘•ƒ”‡ƒ†‡ǡ–Š‡ˆƒ—Ž–•ˆ”‘‡ƒ Š—‹–
ƒ„‡”‡“—‡•–‡†—•‹‰†‹”‘™•‡”Ǥ–ƒ”–™‹–Š–Š‡ —•‹‘‘” —•‹‘‹†‡„ƒ†ƒ‹ —„ƒ†
™‘”†‘™•–”‡ƒǤ
‡•‘Ž˜‡ƒŽŽˆƒ—Ž–•ˆ‹”•–ƒ†–Š‡ Š‡ –Š‡™ƒ”‹‰•Ǥƒ‡ƒ’’”‘’”‹ƒ–‡ƒ –‹‘–‘”‡•‘Ž˜‡–Š‡ˆƒ—Ž–•ǡ
ƒ•‹†‹ ƒ–‡†‹–Š‡ˆ‘ŽŽ‘™‹‰–ƒ„Ž‡•Ǥ  ƒ•‡•™Š‡”‡–Š‡”‡‹•‘”‡–Šƒ‘‡’‘••‹„Ž‡ ƒ—•‡ǡ–Š‡›ƒ”‡
Ž‹•–‡†ˆ”‘–Š‡Dz‘•–Ž‹‡Ž›dz–‘–Š‡DzŽ‡ƒ•–Ž‹‡Ž›dz ƒ—•‡Ǥ –‹‘•ƒ”‡Ž‹•–‡†‹–Š‡‘”†‡”–Šƒ––Š‡›
•Š‘—Ž†„‡’‡”ˆ‘”‡†Ǣ‘–ƒŽŽƒ –‹‘•ƒ›‡‡†–‘„‡†‘‡Ǥ
NOTE:
IfyouhavearedSTATUSLEDwithoutafaultmessage,itprobablyindicatesthattheunitislocked
out.
Table98. FaultMessagesforMainHubs
Message
Number
Description
Reason/Action
{MF01}
Software error occurred and recovered.
If this happens repeatedly, replace the Hub.
{MF02}
Software error occurred and recovered.
If this happens repeatedly, replace the Hub.
{MF03}
Software error occurred and recovered.
If this happens repeatedly, replace the Hub.
{MF04}
Software reset occurred and recovered, or firmware
download.
If this happens repeatedly, replace the Hub.
{MF05}
Software error occurred and recovered.
If this happens repeatedly, replace the Hub.
{MF06}
Problem detected in the Hub. Internal communication
reset.
Contact TE Support for more information.
{MF07}
Hub power cycle.
Hub power cycle.
{MF08}
Internal communications failure.
No internal communications in preceding 15 minutes.
{MF09}
Hardware Reset.
Commanded hardware power on reset
{MF10}
Band not programmed.
Use AdminBrowser to program the band.
{MF11}
Hardware failure (DL Pilot PLL).
Cycle power once. If fault persists, replace the Hub
{MF12}
Hardware failure (DL Pilot Too High).
Cycle power once. If fault persists, replace the Hub.
{MF13}
Hardware failure (DL Pilot Too Low).
Cycle power once. If fault persists, replace the Hub.
{MF14}
Hardware failure (54 VDC).
54 VDC power supply is out of range, replace the Hub
{MF15}
Hardware failure (RF VDC Power).
Loss of DC power to RF circuits, replace the Hub.
{MF16}
Self Lockout (All Bands).
Hub has shutdown the system due to an internal fault.
System is offline.
{MF17}
Hardware failure (DL PLL Band 1).
Cycle power once. If fault persists, replace the Hub.
{MF18}
Hardware failure (UL PLL Band 1).
Cycle power once. If fault persists, replace the Hub
{ML19}
Commanded Out-of-service (Band 1).
Band 1 commanded out-of-service by User.
{MF20}
Hardware failure (UL1 LO2 Band 1).
Cycle power once. If the fault persists, replace the Hub.
{MF21}
Problem detected in the Hub.
Contact TE Support for more information.
{MF22}
Problem detected in the Hub.
Contact TE Support for more information.
{MF23}
Problem detected in the Hub
Contact TE Support for more information.
{MF24}
Problem detected in the Hub.
Contact TE Support for more information.
{MF25}
Hardware failure (DL PLL Band 2).
Cycle power once. If fault persists, replace the Hub.
Page 210
Š 2013 TE Connectivity Ltd
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Faults Reported by Main Hubs
Table98. FaultMessagesforMainHubs(Cont.)
Message
Number
Description
Reason/Action
{MF26}
Hardware failure (UL PLL Band 2).
Cycle power once. If fault persists, replace the Hub.
{ML27}
Commanded Out-of-service (Band 2).
Band 2 commanded out-of-service by User.
{MF28}
Problem detected in the Hub.
Contact TE Support for more information.
{MF29}
Problem detected in the Hub.
Contact TE Support for more information.
{MF30}
Problem detected in the Hub.
Contact TE Support for more information.
{MF31}
Problem detected in the Hub.
Contact TE Support for more information.
{MF32}
Problem detected in the Hub.
Contact TE Support for more information.
{MF33}
Hardware failure (DL PLL Band 3).
Cycle power once. If fault persists, replace the Hub.
{MF34}
Hardware failure (UL PLL Band 3).
Cycle power once. If fault persists, replace the Hub.
{ML35}
Commanded Out-of-service (Band 3).
Band 3 commanded out-of-service by User.
{MF36}
Hardware failure (638 MHz PLL).
Cycle power once. If fault persists, replace the Hub.
{MF37}
Hardware failure (638 MHz PLL).
Cycle power once. If fault persists, replace the Hub.
{MF38}
Problem detected in the Hub.
Contact TE Support for more information.
{MF39}
Problem detected in the Hub.
Contact TE Support for more information.
{MF40}
Problem detected in the Hub.
Contact TE Support for more information.
{MF41}
Hardware failure (Optical Power Out).
Cycle power once. If the fault persists, replace the Hub.
{MF42}
Unable to sync with TDD frame (Band 1).
Check input signal and/or user TDD settings.
{MF43}
Unable to sync with TDD frame (Band 2).
Check input signal and/or user TDD settings.
{MF44}
Problem detected in the Hub.
Contact TE Support for more information
{MF45}
Problem detected in the Hub.
Contact TE Support for more information.
{MF46}
Problem detected in the Hub.
Contact TE Support for more information.
{MF47}
Problem detected in the Hub
Contact TE Support for more information.
{MF48}
Problem detected in the Hub.
Contact TE Support for more information.
{MD129}
Port 1 Disconnected.
Unit is disconnected.
{MD130}
Port 2 Disconnected.
Unit is disconnected.
{MD131}
Port 3 Disconnected.
Unit is disconnected.
{MD132}
Port 4 Disconnected.
Unit is disconnected.
{MD133}
Port 5 Disconnected.
Unit is disconnected.
{MD134}
Port 6 Disconnected.
Unit is disconnected.
{MD135}
Port 7 Disconnected.
Unit is disconnected.
{MD136}
Port 8 Disconnected.
Unit is disconnected.
{MC137}
Port 1 No Communications.
No communications with remote unit.
{MC138}
Port 2 No Communications.
No communications with remote unit.
{MC139}
Port 3 No Communications.
No communications with remote unit.
{MC140}
Port 4 No Communications.
No communications with remote unit.
{MC141}
Port 5 No Communications.
No communications with remote unit.
{MC142}
Port 6 No Communications.
No communications with remote unit.
{MC143}
Port 7 No Communications.
No communications with remote unit.
{MC144}
Port 8 No Communications.
No communications with remote unit.
{MT145}
Port 1 Cable Fault.
Possible electrical short in the coax cable, or RAU problem.
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Page 211
Š 2013 TE Connectivity Ltd.
Appendix C: Faults, Warnings, Status Tables for Fusion, Fusion Wideband, Fusion SingleStar
Table98. FaultMessagesforMainHubs(Cont.)
Message
Number
Description
Reason/Action
{MT146}
Port 2 Cable Fault.
Possible electrical short in the coax cable, or RAU problem.
{MT147}
Port 3 Cable Fault.
Possible electrical short in the coax cable, or RAU problem.
{MT148}
Port 4 Cable Fault.
Possible electrical short in the coax cable, or RAU problem.
{MT149}
Port 5 Cable Fault.
Possible electrical short in the coax cable, or RAU problem.
{MT150}
Port 6 Cable Fault.
Possible electrical short in the coax cable, or RAU problem.
{MT151}
Port 7 Cable Fault.
Possible electrical short in the coax cable, or RAU problem.
{MT152}
Port 8 Cable Fault.
Possible electrical short in the coax cable, or RAU problem.
{MT153}
Port 1 Trip.
Remote Unit is drawing too much current.
{MT154}
Port 2 Trip.
Remote Unit is drawing too much current.
{MT155}
Port 3 Trip.
Remote Unit is drawing too much current.
{MT156}
Port 4 Trip.
Remote Unit is drawing too much current.
{MT157}
Port 5 Trip.
Remote Unit is drawing too much current.
{MT158}
Port 6 Trip.
Remote Unit is drawing too much current.
{MT159}
Port 7 Trip.
Remote Unit is drawing too much current.
{MT160}
Port 8 Trip.
Remote Unit is drawing too much current.
{MF161}
Problem detected in the Hub.
Contact TE Support for more information.
{MF162}
Problem detected in the Hub.
Contact TE Support for more information.
{MF163}
Problem detected in the Hub.
Contact TE Support for more information.
{MF164}
Problem detected in the Hub.
Contact TE Support for more information.
{MF165}
Problem detected in the Hub.
Contact TE Support for more information.
{MF166}
Problem detected in the Hub.
Contact TE Support for more information.
{MF167}
Problem detected in the Hub.
Contact TE Support for more information.
{MF168}
Problem detected in the Hub.
Contact TE Support for more information.
{MF169}
Problem detected in the Hub.
Contact TE Support for more information.
{MF170}
Problem detected in the Hub.
Contact TE Support for more information.
{MF171}
Problem detected in the Hub.
Contact TE Support for more information.
{MF172}
Problem detected in the Hub.
Contact TE Support for more information.
{MF173}
Problem detected in the Hub.
Contact TE Support for more information.
{MF174}
Problem detected in the Hub.
Contact TE Support for more information.
{MF175}
Problem detected in the Hub.
Contact TE Support for more information.
{MF176}
Problem detected in the Hub.
Contact TE Support for more information.
Page 212
Š 2013 TE Connectivity Ltd
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Faults Reported for System CPU
FAULTSREPORTEDFORSYSTEMCPU
Table99. FaultsforSystemCPU
Message
Number
Description
Reason/Action
{SF01}
No internal communications.
No internal communications in preceding 2 minutes. Power cycle to
clear.
{SF02}
Unable to open file (sysinfo).
System CPU rebooted.
{SF03}
Unable to open file (sysstat).
System CPU rebooted.
{SF04}
Invalid internal response.
System CPU rebooted, internal command does not return valid response
after 4 retries.
{SF05}
No MAC address.
System CPU rebooted, unable to read MAC address from the Ethernet
driver.
{SF06}
Unable to open file (sysinfo_org).
System CPU rebooted.
{SF07}
Unable to open file (sbc_status).
System CPU rebooted.
{SF08}
Invalid internal field response.
System CPU rebooted, internal command format invalid.
{SF09}
Unable to open file (fileTTL).
System CPU rebooted.
{SF10}
Invalid internal ASCII response.
System CPU rebooted, illegal number of bytes.
{SF11}
Unable to open file (sysalarm).
System CPU rebooted.
{SF12}
Unable to open file (password_etb).
System CPU rebooted.
{SF13}
Unable to open file (CRC).
System CPU rebooted.
{SF14}
Problem detected in the System CPU.
Contact TE Support for more information.
{SF15}
pThread not executing.
System CPU rebooted.
{SF16}
Problem detected in the System CPU.
Contact TE Support for more information.
{SF17}
Problem detected in the System CPU.
Contact TE Support for more information.
{SF18}
Problem detected in the System CPU.
Contact TE Support for more information.
{SF19}
Problem detected in the System CPU.
Contact TE Support for more information.
{SF20}
Problem detected in the System CPU.
Contact TE Support for more information.
{SF21}
Problem detected in the System CPU.
Contact TE Support for more information.
{SF22}
Problem detected in the System CPU.
Contact TE Support for more information.
{SF23}
Problem detected in the System CPU.
Contact TE Support for more information.
{SF24}
Problem detected in the System CPU.
Contact TE Support for more information.
{SF25}
Problem detected in the System CPU.
Contact TE Support for more information.
{SF26}
Problem detected in the System CPU.
Contact TE Support for more information.
{SF27}
Problem detected in the System CPU.
Contact TE Support for more information.
{SF28}
Problem detected in the System CPU.
Contact TE Support for more information.
{SF29}
Problem detected in the System CPU.
Contact TE Support for more information.
{SF30}
Problem detected in the System CPU.
Contact TE Support for more information.
{SF31}
Problem detected in the System CPU.
Contact TE Support for more information.
{SF32}
Problem detected in the System CPU.
Contact TE Support for more information.
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Page 213
Š 2013 TE Connectivity Ltd.
Appendix C: Faults, Warnings, Status Tables for Fusion, Fusion Wideband, Fusion SingleStar
FAULTSFOREXPANSIONHUBS
Table100. FaultMessagesforExpansionHubs
Message
Number
Description
Reason/Action
{EF01}
Software error occurred and recovered.
If this happens repeatedly, replace the Hub.
{EF02}
Software reset occurred and recovered, or
firmware download.
If this happens repeatedly, replace the Hub.
{EF03}
Software reset occurred and recovered.
If this happens repeatedly, replace the Hub.
{EF04}
Software reset occurred and recovered.
If this happens repeatedly, replace the Hub.
{EF05}
Software error occurred and recovered.
If this happens repeatedly, replace the Hub.
{EF06}
Firmware download.
Firmware download.
{EF07}
Hub power cycle.
Hub power cycle.
{EF08}
MH communications failure.
No communications from MH in THE preceding 90 seconds.
{EF09}
MH communications failure.
EH uplink messages not getting to the MH.
{EF10}
Hardware failure (PLL).
Cycle power once. If the fault persists, replace the Hub.
{EF11}
Hardware failure (54 VDC).
54 VDC power supply is out of range, replace the Hub.
{EF12}
Problem detected in the EH.
Contact TE Support for more information.
{EF13}
Band not programmed.
Cycle power once. If the fault persists, replace the Hub.
{EF14}
Low optical input power.
Check downlink fiber connections.
{EF15}
Hardware failure (Optical Output Power).
Cycle power once. If the fault persists, replace the Hub.
{EF16}
Self Lockout (All Bands).
The Hub has shutdown the system due to an internal fault. The
system is offline.
{EF17}
Commanded Out-of-service (Band 1).
Band 1 commanded out-of-service by the user.
{EF18}
Fault lockout (Band 1).
Band 1 out-of-service due to an MH fault.
{EF19}
Problem detected in the EH.
Contact TE Support for more information.
{EF20}
Problem detected in the EH.
Contact TE Support for more information.
{EF21}
Problem detected in the EH.
Contact TE Support for more information.
{EF22}
Problem detected in the EH.
Contact TE Support for more information.
{EF23}
Problem detected in the EH.
Contact TE Support for more information.
{EF24}
Problem detected in the EH.
Contact TE Support for more information.
{EF25}
Commanded Out-of-service (Band 2).
Band 2 commanded out-of-service by the user.
{EF26}
Fault lockout (Band 2).
Band 2 out-of-service due to MH fault.
{EF27}
Problem detected in the EH.
Contact TE Support for more information.
{EF28}
Problem detected in the EH.
Contact TE Support for more information.
{EF29}
Problem detected in the EH.
Contact TE Support for more information.
{EF30}
Problem detected in the EH.
Contact TE Support for more information.
{EF31}
Problem detected in the EH.
Contact TE Support for more information.
{EF32}
Problem detected in the EH.
Contact TE Support for more information.
{EF33}
Commanded Out-of-service (Band 3).
Band 3 commanded out-of-service by the user.
{EF34}
Fault lockout (Band 3).
Band 3 out-of-service due to an MH fault.
{EF35}
Problem detected in the EH.
Contact TE Support for more information.
{EF36}
Problem detected in the EH.
Contact TE Support for more information.
Page 214
Š 2013 TE Connectivity Ltd
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Faults for Expansion Hubs
Table100. FaultMessagesforExpansionHubs(Cont.)
Message
Number
Description
Reason/Action
{EF37}
Problem detected in the EH.
Contact TE Support for more information.
{EF38}
Problem detected in the EH.
Contact TE Support for more information.
{EF39}
Problem detected in the EH.
Contact TE Support for more information.
{EF40}
Problem detected in the EH.
Contact TE Support for more information.
{ED129}
Port 1 Disconnected.
Unit is disconnected.
{ED130}
Port 2 Disconnected.
Unit is disconnected.
{ED131}
Port 3 Disconnected.
Unit is disconnected.
{ED132}
Port 4 Disconnected.
Unit is disconnected.
{ED133}
Port 5 Disconnected.
Unit is disconnected.
{ED134}
Port 6 Disconnected.
Unit is disconnected.
{ED135}
Port 7 Disconnected.
Unit is disconnected.
{ED136}
Port 8 Disconnected.
Unit is disconnected.
{EC137}
Port 1 No Communications.
No communications with remote unit.
{EC138}
Port 2 No Communications.
No communications with remote unit.
{EC139}
Port 3 No Communications.
No communications with remote unit.
{EC140}
Port 4 No Communications.
No communications with remote unit.
{EC141}
Port 5 No Communications.
No communications with remote unit.
{EC142}
Port 6 No Communications.
No communications with remote unit.
{EC143}
Port 7 No Communications.
No communications with remote unit.
{EC144}
Port 8 No Communications.
No communications with remote unit.
{ET145}
Port 1 Cable Fault.
Possible electrical short in the coaxial cable, or an RAU problem.
{ET146}
Port 2 Cable Fault.
Possible electrical short in the coaxial cable, or an RAU problem.
{ET147}
Port 3 Cable Fault.
Possible electrical short in the coaxial cable, or an RAU problem.
{ET148}
Port 4 Cable Fault.
Possible electrical short in the coaxial cable, or an RAU problem.
{ET149}
Port 5 Cable Fault.
Possible electrical short in the coaxial cable, or an RAU problem.
{ET150}
Port 6 Cable Fault.
Possible electrical short in the coaxial cable, or an RAU problem.
{ET151}
Port 7 Cable Fault.
Possible electrical short in the coaxial cable, or an RAU problem.
{ET152}
Port 8 Cable Fault.
Possible electrical short in the coaxial cable, or an RAU problem.
{ET153}
Port 1 Trip.
The Remote Unit is drawing too much current.
{ET154}
Port 2 Trip.
The Remote Unit is drawing too much current.
{ET155}
Port 3 Trip.
The Remote Unit is drawing too much current.
{ET156}
Port 4 Trip.
The Remote Unit is drawing too much current.
{ET157}
Port 5 Trip.
The Remote Unit is drawing too much current.
{ET158}
Port 6 Trip.
The Remote Unit is drawing too much current.
{ET159}
Port 7 Trip.
The Remote Unit is drawing too much current.
{ET160}
Port 8 Trip.
The Remote Unit is drawing too much current.
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Page 215
Š 2013 TE Connectivity Ltd.
Appendix C: Faults, Warnings, Status Tables for Fusion, Fusion Wideband, Fusion SingleStar
FAULTSFORRAUS
Table101. FaultsforRAUs
Message
Number
Description
Reason/Action
{RF01}
Software error occurred and recovered.
If this happens repeatedly, replace the RAU.
{RF02}
Software error occurred and recovered.
If this happens repeatedly, replace the RAU.
{RF03}
Software error occurred and recovered.
If this happens repeatedly, replace the RAU.
{RF04}
Software reset occurred and recovered, or firmware
download.
If this happens repeatedly, replace the RAU.
{RF05}
Software error occurred and recovered.
If this happens repeatedly, replace the RAU.
{RF06}
Problem detected in the RAU.
Contact TE Support for more information.
{RF07}
RAU power cycle.
RAU power cycle.
{RF08}
Problem detected in the RAU.
Contact TE Support for more information.
{RF09}
Invalid band.
The RAU doesn't support programmed band. Check the
RAU type against the band programmed in the hub.
{RF10}
Low input DC voltage.
Check the coaxial cable for high RF loss. Try another Hub
port. If the fault persists, replace the RAU. If the fault clears,
mark the Hub port as unusable and replace the Hub when
possible.
{RF11}
Hardware Failure (DL PLL Band 1).
Cycle power once. If the fault persists, replace the RAU.
{RF12}
Hardware Failure (DL PLL Band 2).
Cycle power once. If the fault persists, replace the RAU.
{RF13}
Hardware Failure (DL PLL Band 3).
Cycle power once. If the fault persists, replace the RAU.
{RF14}
Hardware Failure (UL PLL Band 1).
Cycle power once. If the fault persists, replace the RAU.
{RF15}
Hardware Failure (UL PLL Band 2).
Cycle power once. If the fault persists, replace the RAU.
{RF16}
Hardware Failure (UL PLL Band 3).
Cycle power once. If the fault persists, replace the RAU.
{RF17}
Hardware Failure (PA Band 1).
Cycle power once. If the fault persists, replace the RAU.
{RF18}
Hardware Failure (PA Band 2).
Cycle power once. If the fault persists, replace the RAU.
{RF19}
Hardware Failure (PA Band 3).
Cycle power once. If the fault persists, replace the RAU.
{RF20}
Hardware Failure (UL Pilot).
Cycle power once. If the fault persists, replace the RAU.
{RL21}
Commanded Out-of-service (Band 1).
Band 1 commanded out-of-service by User. Command
In-Service on Band 1 to restore service.
{RL22}
Commanded Out-of-service (Band 2).
Band 2 commanded out-of-service by User. Command
In-Service on Band 2 to restore service.
{RL23}
Commanded Out-of-service (Band 3).
Band 3 commanded out-of-service by User. Command
In-Service on Band 3 to restore service.
{RF24}
Problem detected in the RAU.
Contact TE Support for more information.
{RX25}
Commanded shutdown (Band 1).
Check the status of hub to which the RAU is connected.
{RX26}
Commanded shutdown (Band 2).
Check the status of hub to which the RAU is connected.
{RX27}
Commanded shutdown (Band 3).
Check the status of the hub to which the RAU is connected.
{RF28}
Internal shutdown (Band 1).
RAU Fault condition in band 1 path (or common path).
{RF29}
Internal shutdown (Band 2).
RAU Fault condition in band 2 path (or common path).
{RF30}
Internal shutdown (Band 3).
RAU Fault condition in band 3 path (or common path).
{RF31}
Problem detected in the system.
Contact TE Support for more information.
{RF32}
Problem detected in the RAU.
Contact TE Support for more information.
Page 216
Š 2013 TE Connectivity Ltd
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Messages for Main Hubs
MESSAGESFORMAINHUBS
WarningMessages
ƒ”‹‰•ƒŽ‡”–›‘—–‘ ‘†‹–‹‘•–Šƒ–‹†‹ ƒ–‡’‘••‹„Ž‡•‡”˜‹ ‡‹’ƒ –Ǥƒ”‹‰•ƒ”‡†‹•’Žƒ›‡†‹
–Š‡‡••ƒ‰‡•’ƒ‡‹”‡†Ž‡––‡”‹‰Ǥ
‡ˆ‘”‡ƒ††”‡••‹‰™ƒ”‹‰•ǡ‡•—”‡–Šƒ–ƒŽŽˆƒ—Ž–•ƒ”‡”‡•‘Ž˜‡†Ǥƒ‡ƒ’’”‘’”‹ƒ–‡ƒ –‹‘–‘
”‡•‘Ž˜‡–Š‡™ƒ”‹‰•ǡƒ•‹†‹ ƒ–‡†‹–Š‡ˆ‘ŽŽ‘™‹‰–ƒ„Ž‡•Ǥ
NOTE:
AdminBrowser v000007 or higher displays events (faults, warnings, or status messages)
depending on your view preference. To change your view preference, refer to Section 3.5,
“Faults,Warnings,andStatusMessages”oftheFusionInstallation,Operation,andMaintenance
Manual.
StatusMessages
–ƒ–—•‡••ƒ‰‡•ƒŽ‡”–›‘—–‘ ‘†‹–‹‘•–Šƒ–ƒ”‡‹’‘”–ƒ–ǡ„—–‰‡‡”ƒŽŽ›†‘‘–‹’ƒ –•‡”˜‹ ‡Ǥ
–ƒ–—•‡••ƒ‰‡•ƒŽ‡”–›‘—–‘ ‘†‹–‹‘•–Šƒ–ƒ”‡‹’‘”–ƒ–ǡ„—–‰‡‡”ƒŽŽ›†‘‘–‹’ƒ –•‡”˜‹ ‡Ǥ
–ƒ–—•‡••ƒ‰‡•ƒ”‡†‹•’Žƒ›‡†‹–Š‡‡••ƒ‰‡•’ƒ‡‹„Ž—‡Ž‡––‡”‹‰Ǥ
NOTE:
AdminBrowser v000007 or higher displays events (faults, warnings, or status messages)
depending on your view preference. To change your view preference, refer to Section 3.5,
“Faults,Warnings,andStatusMessages”oftheFusionInstallation,Operation,andMaintenance
Manual.
NOTE:
Theiconsdisplayedinthesystemstatustreeassumethattherearenootherfaults,warnings,or
statuspresent.
ƒ„Ž‡ͳͲʹ‘’ƒ‰‡ʹͳͺǡ–Š‡‡••ƒ‰‡—„‡”‹•‹–Š‡ˆ‘ŽŽ‘™‹‰ˆ‘”ǣ
[Mnn]/X
™Š‡”‡
•
nn‡“—ƒŽ•–Š‡‡••ƒ‰‡—„‡”
•
X‡“—ƒŽ•–Š‡†‡ˆƒ—Ž–‘ˆ‘‡‘ˆ–Š‡ˆ‘ŽŽ‘™‹‰
– S—–ƒ–—•
– W—ƒ”‹‰Ǥ
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Page 217
Š 2013 TE Connectivity Ltd.
Appendix C: Faults, Warnings, Status Tables for Fusion, Fusion Wideband, Fusion SingleStar
Table102. Warnings/StatusMessagesforMainHubs
Message
Description
Reason/Action
[M01]/S
Fan 1 failure.
Check the fan for rotation, air flow blockage, and dust. Replace the
Hub on high temperature warning.
[M02]/S
Fan 2 failure.
Check the fan for rotation, air flow blockage, and dust. Replace the
Hub on high temperature warning.
[M03]/S
54 VDC Pwr Supply Fan failure.
Check the fan for rotation, air flow blockage, and dust. Replace the
Hub on high temperature warning.
[M04]/W
5 VDC Monitor.
DC power out of range, replace the Hub.
[M05]/W
9 VDC Monitor.
DC power out of range, replace the Hub.
[M06]/W
54 VDC Monitor.
DC power out of range, replace the Hub.
[M07]/W
3 VDC Monitor.
DC power out of range, replace the Hub.
[M08]/W
12 VDC Monitor.
DC power out of range, replace the Hub.
[M09]/W
Temperature High.
Reduce ambient temperature, check for air flow blockage, fan
rotation.
[M10]/W
-5 VDC Monitor.
DC power is out of range, replace the Hub.
[M11]/W
High laser current.
Output laser failure possible, replace the Hub when possible.
[M12]/W
DL path loss is too high
Replace the Hub.
[M13]/S
Low input optical (Port 1).
Check the uplink fiber.
[M14]/S
Low input optical (Port 2).
Check the uplink fiber.
[M15]/S
Low input optical (Port 3).
Check the uplink fiber.
[M16]/S
Low input optical (Port 4).
Check the uplink fiber.
[M17]/S
Hardware failure (Test Tone PLL Band 1).
Unable to perform DL system test.
[M18]/S
Hardware failure (Test Tone Too High Band 1). Unable to perform DL system test.
[M19]/S
Hardware failure (Test Tone Too Low Band 1). Unable to perform DL system test.
[M20]/W
Overdrive limiter active (Band 1).
Reduce input signal power to avoid potential component damage.
[M21]/W
CEMark limiter at maximum (Band 1).
Reduce input signal power to avoid drop in system gain.
[M22]/W
No DL test tone (Band 1).
Hub DL gain is low.
[M23]/S
No UL test tone (Band 1).
Hub UL path gain is low.
[M24]/S
Problem detected in the system.
Contact TE Support for more information.
[M25]/S
Hardware failure (Test Tone PLL Band 2).
Unable to perform DL system test. Replace the hub when possible.
[M26]/S
Hardware failure (Test Tone Too High Band 2). Unable to perform DL system test. Replace the hub when possible.
[M27]/S
Hardware failure (Test Tone Too Low Band 2). Unable to perform DL system test. Replace the hub when possible.
[M28]/W
Overdrive limiter active (Band 2).
Reduce input signal power to avoid potential component damage.
[M29]/W
CEMark limiter at maximum (Band 2).
Reduce input signal power to avoid drop in system gain.
[M30]/W
No DL test tone (Band 2).
Hub DL path gain is low.
[M31]/S
No UL test tone (Band 2).
Hub UL path gain is low.
[M32]/S
Problem detected in the system.
Contact TE Support for more information.
[M33]/S
Hardware failure (Test Tone PLL Band 3).
Unable to perform DL system test.
[M34]/S
Hardware failure (Test Tone Too High Band 3). Unable to perform DL system test.
[M35]/S
Hardware failure (Test Tone Too Low Band 3). Unable to perform DL system test.
[M36]/W
Overdrive limiter active (Band 3).
Number/
Default
Page 218
Š 2013 TE Connectivity Ltd
Reduce input signal power to avoid potential component damage.
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Messages for Main Hubs
Table102. Warnings/StatusMessagesforMainHubs(Cont.)
Message
Description
Reason/Action
[M37]/W
CEMark limiter at maximum (Band 3).
Reduce input signal power to avoid drop in system gain.
[M38]/W
No DL test tone (Band 3).
Hub DL path gain is low.
[M39]/S
No UL test tone (Band 3).
Hub UL path gain is low.
[M40]/S
Problem detected in the Hub.
Contact TE Support for more information.
[M41]/W
Port 1 No DL test tone (Band 1).
Hub/Port DL path gain is low.
[M42]/W
Port 2 No DL test tone (Band 1).
Hub/Port DL path gain is low.
[M43]/W
Port 3 No DL test tone (Band 1).
Hub/Port DL path gain is low.
[M44]/W
Port 4 No DL test tone (Band 1).
Hub/Port DL path gain is low.
[M45]/W
Port 5 No DL test tone (Band 1).
Hub/Port DL path gain is low.
[M46]/W
Port 6 No DL test tone (Band 1).
Hub/Port DL path gain is low.
[M47]/W
Port 7 No DL test tone (Band 1).
Hub/Port DL path gain is low.
[M48]/W
Port 8 No DL test tone (Band 1).
Hub/Port DL path gain is low.
[M49]/W
Port 1 No DL test tone (Band 2).
Hub/Port DL path gain is low.
[M50]/W
Port 2 No DL test tone (Band 2).
Hub/Port DL path gain is low.
[M51]/W
Port 3 No DL test tone (Band 2).
Hub/Port DL path gain is low.
[M52]/W
Port 4 No DL test tone (Band 2).
Hub/Port DL path gain is low.
[M53]/W
Port 5 No DL test tone (Band 2).
Hub/Port DL path gain is low.
[M54]/W
Port 6 No DL test tone (Band 2).
Hub/Port DL path gain is low.
[M55]/W
Port 7 No DL test tone (Band 2).
Hub/Port DL path gain is low.
[M56]/W
Port 8 No DL test tone (Band 2).
Hub/Port DL path gain is low.
[M57]/W
Port 1 No DL test tone (Band 3).
Hub/Port DL path gain is low.
[M58]/W
Port 2 No DL test tone (Band 3).
Hub/Port DL path gain is low.
[M59]/W
Port 3 No DL test tone (Band 3).
Hub/Port DL path gain is low.
[M60]/W
Port 4 No DL test tone (Band 3).
Hub/Port DL path gain is low.
[M61]/W
Port 5 No DL test tone (Band 3).
Hub/Port DL path gain is low.
[M62]/W
Port 6 No DL test tone (Band 3).
Hub/Port DL path gain is low.
[M63]/W
Port 7 No DL test tone (Band 3).
Hub/Port DL path gain is low.
[M64]/W
Port 8 No DL test tone (Band 3).
Hub/Port DL path gain is low.
[M65]/S
No UL test tone Port 1 (Band 1).
Hub/Port UL path gain is low.
[M66]/S
No UL test tone Port 2 (Band 1).
Hub/Port UL path gain is low.
[M67]/S
No UL test tone Port 3 (Band 1).
Hub/Port UL path gain is low.
[M68]/S
No UL test tone Port 4 (Band 1).
Hub/Port UL path gain is low.
[M69]/S
No UL test tone Port 1 (Band 2).
Hub/Port UL path gain is low.
[M70]/S
No UL test tone Port 2 (Band 2).
Hub/Port UL path gain is low.
[M71]/S
No UL test tone Port 3 (Band 2).
Hub/Port UL path gain is low.
[M72]/S
No UL test tone Port 4 (Band 2).
Hub/Port UL path gain is low.
[M73]/S
No UL test tone Port 1 (Band 3).
Hub/Port UL path gain is low.
[M74]/S
No UL test tone Port 2 (Band 3).
Hub/Port UL path gain is low.
[M75]/S
No UL test tone Port 3 (Band 3).
Hub/Port UL path gain is low.
Number/
Default
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Page 219
Š 2013 TE Connectivity Ltd.
Appendix C: Faults, Warnings, Status Tables for Fusion, Fusion Wideband, Fusion SingleStar
Table102. Warnings/StatusMessagesforMainHubs(Cont.)
Message
Description
Reason/Action
[M76]/S
No UL test tone Port 4 (Band 3).
Hub/Port UL path gain is low.
[M77]/S
Problem detected in the Hub.
Contact TE Support for more information.
[M78]/S
Problem detected in the Hub.
Contact TE Support for more information.
[M79]/S
Problem detected in the Hub.
Contact TE Support for more information.
[M80]/S
Problem detected in the Hub.
Contact TE Support for more information.
[M81]/W
Port 1 DL path loss is high.
If the problem is on more than one port, replace the Hub. Switch
the cable connection to a different hub port until the Hub can be
replaced.
[M82]/W
Port 2 DL path loss is high.
If the problem is on more than one port, replace the Hub. Switch
the cable connection to a different hub port until the Hub can be
replaced.
[M83]/W
Port 3 DL path loss is high.
If the problem is on more than one port, replace the Hub. Switch
the cable connection to a different hub port until the Hub can be
replaced.
[M84]/W
Port 4 DL path loss is high.
If the problem is on more than one port, replace the Hub. Switch
the cable connection to a different hub port until the Hub can be
replaced.
[M85]/W
Port 5 DL path loss is high.
If the problem is on more than one port, replace the Hub. Switch
the cable connection to a different hub port until the Hub can be
replaced.
[M86]/W
Port 6 DL path loss is high.
If the problem is on more than one port, replace the Hub. Switch
the cable connection to a different hub port until the Hub can be
replaced.
[M87]/W
Port 7 DL path loss is high.
If the problem is on more than one port, replace the Hub. Switch
the cable connection to a different hub port until the Hub can be
replaced.
[M88]/W
Port 8 DL path loss is high.
If the problem is on more than one port, replace the Hub. Switch
the cable connection to a different hub port until the Hub can be
replaced.
[M89]/W
Port 1 UL path loss is high.
Check the cable for high RF loss. Switch the cable connection to a
different hub port. If the problem on more than one port, replace
the Hub, otherwise replace the RAU.
[M90]/W
Port 2 UL path loss is high.
Check the cable for high RF loss. Switch the cable connection to a
different hub port. If the problem is on more than one port, replace
the Hub, otherwise replace the RAU.
[M91]/W
Port 3 UL path loss is high.
Check the cable for high RF loss. Switch the cable connection to a
different hub port. If the problem is on more than one port, replace
the Hub, otherwise replace the RAU.
[M92]/W
Port 4 UL path loss is high.
Check the cable for high RF loss. Switch the cable connection to a
different hub port. If the problem is on more than one port, replace
the Hub, otherwise replace the RAU.
[M93]/W
Port 5 UL path loss is high.
Check the cable for high RF loss. Switch the cable connection to a
different hub port. If the problem is on more than one port, replace
the Hub, otherwise replace the RAU.
[M94]/W
Port 6 UL path loss is high.
Check the cable for high RF loss. Switch the cable connection to a
different hub port. If the problem is on more than one port, replace
the Hub, otherwise replace the RAU.
Number/
Default
Page 220
Š 2013 TE Connectivity Ltd
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Messages for Main Hubs
Table102. Warnings/StatusMessagesforMainHubs(Cont.)
Message
Description
Reason/Action
[M95]/W
Port 7 UL path loss is high.
Check the cable for high RF loss. Switch the cable connection to a
different hub port. If the problem is on more than one port, replace
the Hub, otherwise replace the RAU.
[M96]/W
Port 8 UL path loss is high.
Check the cable for high RF loss. Switch the cable connection to a
different hub port. If the problem is on more than one port, replace
the Hub, otherwise replace the RAU.
[M97]/W
Port 1 UL path exceeds maximum gain.
If the problem is common to more than one port, replace the Hub,
otherwise check the RAU.
[M98]/W
Port 2 UL path exceeds maximum gain.
If the problem is common to more than one port, replace the Hub,
otherwise check the RAU.
[M99]/W
Port 2 UL path exceeds maximum gain.
If the problem is common to more than one port, replace the Hub,
otherwise check the RAU.
[M100]/W
Port 2 UL path exceeds maximum gain.
If the problem is common to more than one port, replace the Hub,
otherwise check the RAU.
[M101]/W
Port 2 UL path exceeds maximum gain.
If the problem is common to more than one port, replace the Hub,
otherwise check the RAU.
[M102]/W
Port 2 UL path exceeds maximum gain.
If the problem is common to more than one port, replace the Hub,
otherwise check the RAU.
[M103]/W
Port 2 UL path exceeds maximum gain.
If the problem is common to more than one port, replace the Hub,
otherwise check the RAU.
[M104]/W
Port 8 UL path exceeds maximum gain.
If the problem is common to more than one port, replace the Hub,
otherwise check the RAU.
[M105]/W
Port 1 54 VDC Power Enabled.
Caution: Port 54 VDC power may be present at the output.
[M106]/W
Port 2 54 VDC Power Enabled.
Caution: Port 54 VDC power may be present at the output.
[M107]/W
Port 3 54 VDC Power Enabled.
Caution: Port 54 VDC power may be present at the output.
[M108]/W
Port 4 54 VDC Power Enabled.
Caution: Port 54 VDC power may be present at the output.
[M109]/W
Port 5 54 VDC Power Enabled.
Caution: Port 54 VDC power may be present at the output.
[M110]/W
Port 6 54 VDC Power Enabled.
Caution: Port 54 VDC power may be present at the output.
[M111]/W
Port 7 54 VDC Power Enabled.
Caution: Port 54 VDC power may be present at the output.
[M112]/W
Port 8 54 VDC Power Enabled.
Caution: Port 54 VDC power may be present at the output.
Number/
Default
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Page 221
Š 2013 TE Connectivity Ltd.
Appendix C: Faults, Warnings, Status Tables for Fusion, Fusion Wideband, Fusion SingleStar
MESSAGESFORSYSTEMCPUS
ƒ„Ž‡ͳͲ͵ǡ–Š‡‡••ƒ‰‡—„‡”‹•‹–Š‡ˆ‘ŽŽ‘™‹‰ˆ‘”ǣ
[Snn]/X
™Š‡”‡
•
nn‡“—ƒŽ•–Š‡‡••ƒ‰‡—„‡”
•
X‡“—ƒŽ•–Š‡†‡ˆƒ—Ž–‘ˆ‘‡‘ˆ–Š‡ˆ‘ŽŽ‘™‹‰
– S—–ƒ–—•
– W—ƒ”‹‰Ǥ
Table103. Warning/StatusMessagesforSystemCPUs
Message 
Number/
Default
Description
Reason/Action
[S01]/W
Alarm Input 1.
Check equipment connected to alarm input 1.
[S02]/W
Alarm Input 2.
Check equipment connected to alarm input 2.
[S03]/W
Alarm Input 3.
Check equipment connected to alarm input 3.
[S04]/S
Performed System Test
System has just performed system test.
[S05]/S
Problem detected in the System CPU. Contact TE Support for more information.
[S06]/S
Loaded default etb file.
Contact TE Support for more information.
[S07]/S
Loaded default SBC status file.
Contact TE Support for more information.
[S08]/S
Problem detected in the System CPU. Contact TE Support for more information.
[S09]/S
TTL is full.
[S10]/S
Problem detected in the System CPU. Contact TE Support for more information.
[S11]/S
Problem detected in the System CPU. Contact TE Support for more information.
[S12]/S
Loaded default Password file.
Contact TE Support for more information.
[S13]/S
Loaded default sys config file.
Contact TE Support for more information.
[S14]/S
Communication retries exceeded.
Attempted command three times without response.
[S15]/S
Problem detected in the System CPU. Contact TE Support for more information.
[S16]/S
Problem detected in the System CPU. Contact TE Support for more information.
Page 222
Š 2013 TE Connectivity Ltd
Retrieve the TTL and erase.
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Messages for Expansion Hubs
MESSAGESFOREXPANSIONHUBS
Table104. Warning/StatusMessageforExpansionHubs
Message
Number/De
fault
Description
Reason/Action
[E01]/W
Alarm Input 1.
Check the equipment connected to alarm input 1.
[E02]/W
Alarm Input 2.
Check the equipment connected to alarm input 2.
[E03]/W
Alarm Input 3.
Check the equipment connected to alarm input 3.
[E04]/S
Problem detected in the EH.
Contact TE Support for more information.
[E05]/W
SNMP Trap #1.
TBD.
[E06]/W
SNMP Trap #2.
TBD.
[E07]/W
SNMP Trap #3.
TBD.
[E08]/S
Problem detected in the EH.
Contact TE Support for more information.
[E09]/S
Fan 1 failure.
Check the fan for proper rotation, air flow blockage, and dust accumulation.
Replace the Hub on high temperature warning.
[E10]/S
Fan 2 failure.
Check the fan for proper rotation, air flow blockage, and dust accumulation.
Replace the Hub on high temperature warning.
[E11]/W
-5 VDC Monitor.
DC power out of range, replace the Hub.
[E12]/W
5 VDC Monitor.
DC power out of range, replace the Hub.
[E13]/W
9 VDC Monitor.
DC power out of range, replace the Hub.
[E14]/W
54 VDC Pwr Supply failure.
DC port power supply out of range, replace the Hub.
[E15]/W
3 VDC Monitor.
DC power out of range, replace the Hub.
[E16]/W
12 VDC Monitor.
DC power out of range, replace the Hub.
[E17]/W
Temperature High.
Reduce the ambient temperature, check for air flow blockage, fan rotation.
[E18]/W
DL path exceeds maximum gain.
If the problem is common to more than one port, replace the MH, otherwise
check the EH.
[E19]/W
DL path loss is high.
Check the cable for high RF loss. Switch the cable connection to a different
MH port. If the problem is on more than one port, replace the EH, otherwise
replace the RAU.
[E20]/W
Hardware Failure (High UL Pilot).
Cycle power once. If the fault persists, replace the EH.
[E21]/W
Hardware Failure (Low UL Pilot).
Cycle power once. If the fault persists, replace the EH.
[E22]/W
Low optical input power.
Check the downlink fiber connection.
[E23]/W
High laser current.
Contact TE Support for more information.
[E24]/S
Problem detected in the EH.
Contact TE Support for more information.
[E25]/W
Port 1 No DL test tone (Band 1).
Hub/Port DL path gain is low.
[E26]/W
Port 2 No DL test tone (Band 1).
Hub/Port DL path gain is low.
[E27]/W
Port 3 No DL test tone (Band 1).
Hub/Port DL path gain is low.
[E28]/W
Port 4 No DL test tone (Band 1).
Hub/Port DL path gain is low.
[E29]/W
Port 5 No DL test tone (Band 1).
Hub/Port DL path gain is low.
[E30]/W
Port 6 No DL test tone (Band 1).
Hub/Port DL path gain is low.
[E31]/W
Port 7 No DL test tone (Band 1).
Hub/Port DL path gain is low.
[E32]/W
Port 8 No DL test tone (Band 1).
Hub/Port DL path gain is low.
[E33]/W
Port 1 No DL test tone (Band 2).
Hub/Port DL path gain is low.
[E34]/W
Port 2 No DL test tone (Band 2).
Hub/Port DL path gain is low.
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Page 223
Š 2013 TE Connectivity Ltd.
Appendix C: Faults, Warnings, Status Tables for Fusion, Fusion Wideband, Fusion SingleStar
Table104. Warning/StatusMessageforExpansionHubs(Cont.)
Message
Number/De
fault
Description
Reason/Action
[E35]/W
Port 3 No DL test tone (Band 2).
Hub/Port DL path gain is low.
[E36]/W
Port 4 No DL test tone (Band 2).
Hub/Port DL path gain is low.
[E37]/W
Port 5 No DL test tone (Band 2).
Hub/Port DL path gain is low.
[E38]/W
Port 6 No DL test tone (Band 2).
Hub/Port DL path gain is low.
[E39]/W
Port 7 No DL test tone (Band 2).
Hub/Port DL path gain is low.
[E40]/W
Port 8 No DL test tone (Band 2).
Hub/Port DL path gain is low.
[E41]/W
Port 1 No DL test tone (Band 3).
Hub/Port DL path gain is low.
[E42]/W
Port 2 No DL test tone (Band 3).
Hub/Port DL path gain is low.
[E43]/W
Port 3 No DL test tone (Band 3).
Hub/Port DL path gain is low.
[E44]/W
Port 4 No DL test tone (Band 3).
Hub/Port DL path gain is low.
[E45]/W
Port 5 No DL test tone (Band 3).
Hub/Port DL path gain is low.
[E46]/W
Port 6 No DL test tone (Band 3).
Hub/Port DL path gain is low.
[E47]/W
Port 7 No DL test tone (Band 3).
Hub/Port DL path gain is low.
[E48]/W
Port 8 No DL test tone (Band 3).
Hub/Port DL path gain is low.
[E49]/W
Port 1 DL path loss is high.
If the problem is on more than one port, replace the Hub. Switch the cable
connection to a different hub port until the Hub can be replaced.
[E50]/W
Port 2 DL path loss is high.
If the problem is on more than one port, replace the Hub. Switch the cable
connection to a different hub port until the Hub can be replaced.
[E51]/W
Port 3 DL path loss is high.
If the problem is on more than one port, replace the Hub. Switch the cable
connection to a different hub port until the Hub can be replaced.
[E52]/W
Port 4 DL path loss is high.
If the problem is on more than one port, replace the Hub. Switch the cable
connection to a different hub port until the Hub can be replaced.
[E53]/W
Port 5 DL path loss is high.
If the problem is on more than one port, replace the Hub. Switch the cable
connection to a different hub port until the Hub can be replaced.
[E54]/W
Port 6 DL path loss is high.
If the problem is on more than one port, replace the Hub. Switch the cable
connection to a different hub port until the Hub can be replaced.
[E55]/W
Port 7 DL path loss is high.
If the problem is on more than one port, replace the Hub. Switch the cable
connection to a different hub port until the Hub can be replaced.
[E56]/W
Port 8 DL path loss is high.
If the problem is on more than one port, replace the Hub. Switch the cable
connection to a different hub port until the Hub can be replaced.
[E57]/W
Port 1 UL path loss is high.
Check the cable for high RF loss. Switch the cable connection to a different
hub port. If the problem is on more than one port, replace the Hub,
otherwise replace the RAU.
[E58]/W
Port 2 UL path loss is high.
Check the cable for high RF loss. Switch the cable connection to a different
hub port. If the problem is on more than one port, replace the Hub,
otherwise replace the RAU.
[E59]/W
Port 3 UL path loss is high.
Check the cable for high RF loss. Switch the cable connection to a different
hub port. If the problem is on more than one port, replace the Hub,
otherwise replace the RAU.
[E60]/W
Port 4 UL path loss is high.
Check the cable for high RF loss. Switch the cable connection to a different
hub port. If the problem is on more than one port, replace the Hub,
otherwise replace the RAU.
[E61]/W
Port 5 UL path loss is high.
Check the cable for high RF loss. Switch the cable connection to a different
hub port. If the problem is on more than one port, replace the Hub,
otherwise replace the RAU.
Page 224
Š 2013 TE Connectivity Ltd
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Messages for Expansion Hubs
Table104. Warning/StatusMessageforExpansionHubs(Cont.)
Message
Number/De
fault
Description
Reason/Action
[E62]/W
Port 6 UL path loss is high.
Check the cable for high RF loss. Switch the cable connection to a different
hub port. If the problem is on more than one port, replace the Hub,
otherwise replace the RAU.
[E63]/W
Port 7 UL path loss is high.
Check the cable for high RF loss. Switch the cable connection to a different
hub port. If the problem is on more than one port, replace the Hub,
otherwise replace the RAU.
[E64]/W
Port 8 UL path loss is high.
Check the cable for high RF loss. Switch the cable connection to a different
hub port. If the problem is on more than one port, replace the Hub,
otherwise replace the RAU.
[E65]/W
Port 1 UL path exceeds maximum gain. If the problem is common to more than one port, replace the Hub,
otherwise check RAU.
[E66]/W
Port 2 UL path exceeds maximum gain. If the problem is common to more than one port, replace the Hub,
otherwise check RAU.
[E67]/W
Port 3 UL path exceeds maximum gain. If the problem is common to more than one port, replace the Hub,
otherwise check RAU.
[E68]/W
Port 4 UL path exceeds maximum gain. If the problem is common to more than one port, replace the Hub,
otherwise check RAU.
[E69]/W
Port 5 UL path exceeds maximum gain. If the problem is common to more than one port, replace the Hub,
otherwise check RAU.
[E70]/W
Port 6 UL path exceeds maximum gain. If the problem is common to more than one port, replace the Hub,
otherwise check RAU.
[E71]/W
Port 7 UL path exceeds maximum gain. If problem is common to more than one port, replace the Hub, otherwise
check RAU.
[E72]/W
Port 8 UL path exceeds maximum gain. If the problem is common to more than one port, replace the Hub,
otherwise check RAU.
[E73]/W
Port 1 54 VDC Power Enabled.
Caution: Port 54 VDC power may be present at the output.
[E74]/W
Port 2 54 VDC Power Enabled.
Caution: Port 54 VDC power may be present at the output.
[E75]/W
Port 3 54 VDC Power Enabled.
Caution: Port 54 VDC power may be present at the output.
[E76]/W
Port 4 54 VDC Power Enabled.
Caution: Port 54 VDC power may be present at the output.
[E77]/W
Port 5 54 VDC Power Enabled.
Caution: Port 54 VDC power may be present at the output.
[E78]/W
Port 6 54 VDC Power Enabled.
Caution: Port 54 VDC power may be present at the output.
[E79]/W
Port 7 54 VDC Power Enabled.
Caution: Port 54 VDC power may be present at the output.
[E80]/W
Port 8 54 VDC Power Enabled.
Caution: Port 54 VDC power may be present at the output.
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Page 225
Š 2013 TE Connectivity Ltd.
Appendix C: Faults, Warnings, Status Tables for Fusion, Fusion Wideband, Fusion SingleStar
MESSAGESFORRAUS
ƒ„Ž‡ͳͲͷǡ–Š‡‡••ƒ‰‡—„‡”‹•‹–Š‡ˆ‘ŽŽ‘™‹‰ˆ‘”ǣ
[Rnn]/X
™Š‡”‡
•
nn‡“—ƒŽ•–Š‡‡••ƒ‰‡—„‡”
•
X‡“—ƒŽ•–Š‡†‡ˆƒ—Ž–‘ˆ‘‡‘ˆ–Š‡ˆ‘ŽŽ‘™‹‰
– S—–ƒ–—•
– W—ƒ”‹‰Ǥ
Table105. Warning/StatusMessagesforRAUs
Message 
Number
Default
Description
Reason/Action
[R01]/W
Temperature High.
Check RAU location for excessive temperature; check for air flow
blockage and/or incorrect installation. Move the RAU to a cooler
environment.
[R02]/W
No communications from Hub.
Check the cable for high RF loss. Switch the cable connection to a
different hub port. If the problem persists, replace the RAU.
[R03]/W
DL RF path loss is too high.
Check the cable for high RF loss. Switch the cable connection to a
different hub port. If the problem persists, replace the RAU.
[R04]/W
DL RF path exceeds maximum gain.
Check the Hub for proper operation; switch the cable connection
to a different hub port. If the problem persists, replace the RAU.
[R05]/S
DL RF path problem (Band 1).
Unable to complete the DL system end-to-end test, replace the
RAU when possible.
[R06]/S
DL RF path problem (Band 2).
Unable to complete the DL system end-to-end test, replace the
RAU when possible.
[R07]/S
DL RF path problem (Band 3).
Unable to complete the DL system end-to-end test, replace the
RAU when possible.
[R08]/S
System test required.
Run system test.
[R09]/W
Antenna Disconnected.
Check RAU antenna connection; re-run system test.
[R10]/S
UL RF path problem (Band 1).
Unable to complete the UL system end-to-end test, replace the
RAU when possible.
[R11]/S
UL RF path problem (Band 2).
Unable to complete the UL system end-to-end test, replace the
RAU when possible.
[R12]/S
UL RF path problem (Band 3).
Unable to complete the UL system end-to-end test, replace the
RAU when possible.
[R13]/S
Problem detected in the RAU.
Contact TE Support for more information.
[R14]/S
Problem detected in the RAU.
Contact TE Support for more information.
[R15]/S
Problem detected in the RAU.
Contact TE Support for more information.
[R16]/S
Problem detected in the RAU.
Contact TE Support for more information.
[R17]/S
Antenna disconnected (Band 1).
Check the RAU Band 1 antenna, then rerun the system test.
[R18]/S
Antenna disconnected (Band 2).
Check the RAU Band 2 antenna, then rerun the system test.
[R19]/S
Hardware Failure (UL FD PLL Band 1).
Unable to complete a UL system end-to-end test. Replace the RAU
when possible.
[R20]/W
TDD signaling tone outside valid range (Band 1). If the Main Hub and Expansion Hub are okay, replace the RAU.
Page 226
Š 2013 TE Connectivity Ltd
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Messages for RAUs
Table105. Warning/StatusMessagesforRAUs(Cont.)
Message 
Number
Default
Description
[R21]/W
TDD signaling tone outside valid range (Band 2). If the Main Hub and Expansion Hub are okay, replace the RAU.
[R22]/S
High PA current (Band 1).
The unit is operating with reduced gain. Verify that the input signal
is at the appropriate level. If the problem persists, replace the RAU
when possible.
[R23]/S
High PA current (Band 2).
The unit is operating with reduced gain. Verify that the input signal
is at the appropriate level. If the problem persists, replace the RAU
when possible.
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Reason/Action
Page 227
Š 2013 TE Connectivity Ltd.
Appendix C: Faults, Warnings, Status Tables for Fusion, Fusion Wideband, Fusion SingleStar
Page 228
Š 2013 TE Connectivity Ltd
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
APPENDIXD:CONTACTINGTECONNECTIVITY
ContactingTEConnectivitybyTelephone
Sales
Asia Pacific
+65-6294-9948
France
0800 914032
Germany
0180 2232923
Italy
0800 782374
Spain
900 983291
United Kingdom
0800 960236
USA or Canada
1-800-366-3891
Extension
73000
Connectivity Extension
73475
Wireless Extension
73476
Technical Support
USA or Canada
1-800-530-9960
Elsewhere
+1-952-917-0761
OnlineAccesstoTEConnectivity
Customer Portal
https://www.te.com/commerce/uso/myaccount.do
Technical Support for Wireless Products
http://www.te.com/WirelessSupport
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
Page 229
Š2013 TE Connectivity Ltd.
Appendix D: Contacting TE Connectivity
Page 230
Š 2013 TE Connectivity Ltd
InterReach Fusion Wideband Installation, Operation, and Reference Manual
D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
www.te.com/wireless

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 104
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : 8b1f7477-c60c-11e2-0000-4202e81b4dd1
Producer                        : GPL Ghostscript 8.64
Keywords                        : ()
Modify Date                     : 2013:05:23 08:59:21-05:00
Create Date                     : 2013:05:23 08:59:21-05:00
Creator Tool                    : \376\377\000P\000D\000F\000C\000r\000e\000a\000t\000o\000r\000 \000V\000e\000r\000s\000i\000o\000n\000 \0000\000.\0009\000.\0008
Document ID                     : 8b1f7477-c60c-11e2-0000-4202e81b4dd1
Format                          : application/pdf
Title                           : \376\377\000F\000u\000s\000i\000o\000n\000W\000i\000d\000e\000b\000a\000n\000d\000_\000I\000O\000R\000_\000I\000s\000s\000u\000e\0007\000_\000P\000a\000g\000e\000s\000_\0001\0002\0008\000_\0002\0004\0000\000.\000p\000d\000f
Creator                         : \376\377\000t\000e\0001\0000\0000\0005\0007\0002
Description                     : ()
Author                          : te100572
Subject                         : 

EXIF Metadata provided by EXIF.tools