AGD SYSTEMS MC-133 AGD-T7813-125 MC-133 User Manual Farbgutstrasse 3 CH 9008 St

Download:
Mirror Download [FCC.gov]
Document ID	2940328
Application ID	EGw3c7TpRHwzq1jEJzxDKQ==
Document Description	OEM Instructions
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	47.17kB (589666 bits)
Date Submitted	2016-03-24 00:00:00
Date Available	2016-03-24 00:00:00
Creation Date	2015-08-26 23:11:48
Document Lastmod	2016-03-02 15:17:26
Document Title	Farbgutstrasse 3, CH-9008 St
Document Author:	Klaus Mezger

RFbeam Microwave GmbH
Datasheet
AGD-T7813-125 Issue ‘1’ MC-133
Introduction
This document describes the AGD-T7813 modules Issue ‚1’.
This module has the following features:



Improved Ceramics Material (Temex E2036)
RF-Transistor with higher gain
Adjusted PCB Layout with tighter coupling for Resonator (lower loss)
Electrical Specification
Parameter
Conditions / Notes
Symbol
Min
Typ
Max
Unit
Operating conditions
Supply voltage
Supply current
Vcc
3.15
3.3
6.0
Module enabled
Icc1
40
60
80
mA
RF-Part disabled
Icc2
10
mA
5.5
VCO input voltage
VCO pin resistance
Uvco
Internal pulldown 100k
Rvco

100k
Operating temperature
Top
-20
+70
°C
Storage temperature
Tst
-40
+85
°C
VIH1
2.7
Vcc+ 0.3
VIL1
-0.2
0.7
Power down/Enable
RF power down
Input tied high with pullup 100k
RF enable
Minimum enable time
RF-part fully functional
ton
Maximum hold time
LP capacitor charge error < 10%
toff
Transmitter frequency
UVCO= 3.0V, Tamb= 25°C
fTX
Frequency drift vs temp.
Vcc=3.3V, -20°C .. +70°C
 fTX
Frequency tuning range (VCO)
UVCO= 1V .. 5V
 fvco
s
ms
Transmitter
VCO sensitivity
24.120
24.125
24.130
-0.27
35
Svco
50
GHz
MHz/°C
70
MHz
12.5
MHz/V
VCO Modulation Bandwidth
f=1MHz
BVCO
200
Output power
EIRP
PTX
+13
+20
dBm
Output power deviation
Full VCO tuning range
 PTX
+/- 2
dBm
Spurious emission
According to ETSI 300 440
Pspur
-30
dBm
Antenna gain
FTX=24.125GHz
GAnt
15
dBi
LNA gain
FRX=24.125GHz
GLNA
dB
Mixer Conversion loss
fIF =500Hz
Dmixer
-2.0
dB
Receiver sensitivity
fIF =500Hz, B=1kHz, S/N=6dB
PRX
-114
dBm
Overall sensitivity
fIF =500Hz, B=1kHz, S/N=6dB
Dsystem
-130
dBc
kHz
+16
Receiver
© RFbeam Microwave GmbH www.rfbeam.ch
Page 1/5
RFbeam Microwave GmbH
Datasheet
AGD-T7813-125 Issue ‘1’ MC-133
Parameter
Conditions / Notes
Symbol
Min
Typ
Max
Unit
IF output
IF output impedance
RIF
100

IF Amplifier gain
GIF
30
dB
dB
I/Q amplitude balance
fIF =500Hz, UIF=100mVpp
UIF
I/Q phase shift
fIF =500Hz, UIF=100mVpp

70
IF frequency range
-3dB Bandwidth
fIF_AC
20
IF noise voltage
fIF =500Hz
UIFnoise
1.0
3.2
7.9
V/Hz
fIF =500Hz
UIFnoise
-120
-110
-102
dBV/Hz
IF output offset voltage
Vcc = 3.3V
Uos_AC
1.0
1.5
2.0
Supply rejection
Rejection supply pins to IF outputs, 1kHz
Dsupply
E-Plane
W
H-Plane
W
Horiz. sidelobe suppression
D
Vert. sidelobe suppression
D
-16
90
110
°
500k
Hz
26
dB
Antenna
Horizontal -3dB beamwidth
Vertical -3dB beamwidth
28
30
32
°
28
30
32
°
-20
-25
dB
-20
dB
Body
Outline Dimensions
connector left unconnected
35*65*17
mm3
Weight
62
Connector
pins
Antenna Pattern
Typical Antenna Pattern for one antenna (RX- or TX-side). Measured at 24.200GHz:
© RFbeam Microwave GmbH www.rfbeam.ch
Page 2/5
RFbeam Microwave GmbH
Datasheet
AGD-T7813-125 Issue ‘1’ MC-133
Block diagram
Frequency vs. VCO-Voltage and Temperature
Pin 8 voltage vs. Temperature
© RFbeam Microwave GmbH www.rfbeam.ch
Page 3/5
RFbeam Microwave GmbH
Datasheet
AGD-T7813-125 Issue ‘1’ MC-133
Connector Pinout
On module side a Samtec HW-04-15-F-D-325-SM connector with the following pinout is used:
1:
2:
3:
4:
5:
6:
/Enable
+3.3V
GND
Q Out
I Out
VCO
7:
S&H
8:
Temp
Enable/Disable RF-part. Connect to 0V for normal operation
Power Supply. Connect to +3.3V (3.15V .. 6.0V)
Ground connection. Connect to 0V
Analog Output Q-Channel
Analog Output I-Channel
Frequency control input. A voltage between 1..5V adjusts
TX Frequency by 0 .. 50MHz. Can be used for FSK or FMCW
Sample&Hold Switch Analog Output. Leave it open or connect
to +3.3V for normal operation
Temperature Sensor output of LMT84 temperature sensor
Mechanical Drawing
FCC Labelling Information: (label to be placed into the recess position * shown in the
mechanical drawing above
FCC ID: WH3 -MC-133
AGD-T7813-125 (MC-133)
Frequency 24.125GHz
Issue 1
Serial No: in barcode or datamatrix format
© RFbeam Microwave GmbH www.rfbeam.ch
Page 4/5
RFbeam Microwave GmbH
Datasheet
AGD-T7813-125 Issue ‘1’ MC-133
FCC Approval
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. End users must follow the specific operating
instructions for satisfying RF exposure compliance such that the module should
not be installed in equipment intended to be used within 20cm of the body.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
Changes or modifications not expressly approved by AGD SYSTEMS
Ltd could void the user's authority to operate the equipment
Manufacturers of mobile or fixed devices incorporating MC-133 modules are
authorized to use the FCC Grants of the MC-133 modules for their own final
products according to the conditions referenced in these documents. In this case,
the FCC label of the module shall be visible from the outside, or the host device
shall bear a second label stating "Contains FCC ID: WH3-3-MC-133".
Document History
Author:
Date:
Version:
Changes:
Léon Audergon, RFbeam Microwave GmbH, CH-9008 St. Gallen
th
August 25 2015
1.1
I- and Q-outputs exchanged
Different drawings added
© RFbeam Microwave GmbH www.rfbeam.ch
Page 5/5

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Author                          : Klaus Mezger
Create Date                     : 2015:08:26 23:11:48+02:00
Modify Date                     : 2016:03:02 15:17:26Z
Has XFA                         : No
Language                        : en-US
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Format                          : application/pdf
Creator                         : Klaus Mezger
Title                           : Farbgutstrasse 3, CH-9008 St
Creator Tool                    : Microsoft® Word 2010
Metadata Date                   : 2016:03:02 15:17:26Z
Producer                        : Microsoft® Word 2010
Document ID                     : uuid:bac5a65b-0243-4cfc-8732-72b8cb006df4
Instance ID                     : uuid:b0811319-ea23-4595-a495-9640ab1bec62
Page Count                      : 5

EXIF Metadata provided by EXIF.tools