AISOLUTION KDC400 Barcode Scanner(Bluetooth) User Manual Appendix G KDC400

AISOLUTION CO., LTD. Barcode Scanner(Bluetooth) Appendix G KDC400

Users Manual

KDC400UserManual             November,2011
COPYRIGHT, LICENSE, and WARNING PAGE Copyright  2011 by KoamTac, Inc. All rights reserved.  No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, without permission in writing from KoamTac, Inc. The material in this manual is subject to change without notices. KoamTac reserves the right to make changes to any product to improve reliability, function, or design. KoamTac doesn’t assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein. Follow all warnings and instructions marked on manual and units. Use only the power source specified in this manual or marked on the units. May be covered under one or more pending and/or US Patents, including US Pat. No. 7,769,917; 7,954,710. KDC® is a registered trademark and property of KoamTac, Inc. KoamTac® is a registered trademark and property of KoamTac, Inc. KTSync® is a registered trademark and property of KoamTac, Inc.   TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO ANY TYPE OF MOISTURE. DO NOT LOOK DIRECTLY INTO LASER OR POINT THE LASER INTO ANOTHER PERSON’S EYES. EXPOSURE TO THE BEAM MAY CAUSE EYE DAMAGE.   CAUTION: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user’s authority to operate the equipment.  WARNING: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.   INFORMATION TO USER:  This equipment has been tested and found to comply with the limit of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation; if this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user, is encouraged to try to correct the interference by one or more of the following measures: 1.  Reorient / Relocate the receiving antenna. 2.  Increase the separation between the equipment and receiver. 3.  Connect the equipment into an outlet on a circuit difference from  that to which the receiver is connected. 4.  Consult the dealer or an experienced radio/TV technician for help.  WARNING: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
1. INTRODUCTION Congratulations on purchasing KoamTac’s revolutionary barcode scanner and data collector.  Lightweight and compact, with a user-friendly design and superior functionality, KoamTac’s KDC works in a variety of portable applications.  Use it independently or as an accessory to your PC, PDA, or smartphone.  To find out more about KoamTac, Inc. and our family of products, visit us at www.koamtac.com.  Table 1 - Features of KDC FEATURES  KDC100 KDC200  KDC250  KDC300  KDC400  USB CONNECTIONS  2 1 1 1 1  RECHARGEABLE BATTERY  YES YES YES YES YES  SCAN ENGINE  Laser  Laser Laser Imager  Laser/ Imager  AUTOMATIC DATA UPLOAD  YES  YES YES YES  YES  STORES10,000+ BARCODES  YES YES YES YES No  KTSYNC® SOFTWARE  YES YES YES YES YES  SDK FOR DEVELOPERS  YES YES YES YES YES  SUPPORTS MICROSOFT© WINDOWS XP, VISTA, 7 & MOBILE 5.0+ YES YES YES YES YES  ANDROID, BLACKBERRY, IOS  NO YES YES YES YES  BLUETOOTH NO YES YES YES YES  GPS  NO NO  YES  NO  NO
1.1 KDC Package  The standard KDC package contains: 1.  One KDC Barcode Data Collector 2.  One USB Cable 3. One Lanyard (KDC100/200/250/300) or One Hand Strap (KDC400) 4.  KoamTac Installation CD with  KTSync© for Microsoft Windows XP, Vista, 7 and Mobile 5.0+   KDC Device Driver    User Manual 5.  One Protective KDC Rubber Case (KDC100/200/250/300) or One Smartphone Protective Rubber Case (KDC400)   NOTE:  Depending on your region or distributor, package contents may vary.                                       KDC100/200/250/300                KDC400       Figure 1 – KDC Package
1.2 KDC Characteristics  Before you use your KDC, please become familiar with its physical characteristics. Refer to Figure 2 and Figure 3 below which indicate placement of scan and scroll buttons, OLED display, LEDs, and ports on your KDC.  All KDC models are similar except for the KDC100 which includes an additional USB connector.  KDC100 Barcode Reader and Data Collector     KDC200 / KDC250 / KDC300 Barcode Reader and Data Collector         KDC200   Figure 2 - Characteristics of KDC100
   KDC250/300                 KDC400 Figure 3 - Characteristics of KDC200 / KDC250 / KDC300
2.  INSTALLATION 2.1 KoamTac Installation Wizard  Windows XP WARNING:  DO NOT CONNECT KDC TO USB PORT PRIOR TO INSTALLATION 1.  Insert KoamTac Installation CD into your computer’s CD drive.   2. Click Start icon then My Computer icon.  A listing of devices on your computer will be displayed including the disk drive containing the KoamTac Installation CD.   3.  Click on the KoamTac Installation CD icon then click on the Setup directory.  Click on the PC_Setup.exe file which executes the KTSync Setup Wizard.   NOTES    If KTSync Setup Wizard locates an older version of KTSync on your computer, you will be prompted to remove the older program before installing the new version.  Select Remove KTSync then click Finish.  When removal is complete, click Close.  Go to Step 2 to run KTSync Setup Wizard.     If you have any problems, please refer to the Manual Installation section.    KTSync Setup Wizard Below are the screen images you will see during the installation of KTSync.     Click Next icon in KTSync Setup Wizard window
 Click Next icon in KTSync Confirm Installation window      Within a few minutes, installation of KTSync will be complete.  Click Close icon and wait for the Device Driver Installation Wizard to load.
Device Driver Installation Wizard Below are the screen images you will see during the installation of the KDC Device Driver.     Click Next icon in Device Driver Installation Wizard window    Click Continue Anyway icon in Software Installation Logo testing window    Click Finish icon in Device Driver Installation Wizard window
Connect KDC to Computer Using the USB cable included with the KDC, follow the directions below.  Connect the cable’s ultra mini USB connector to the KDC.  Connect the cable’s Type A USB connector to your PC.  Wait until your computer beeps and/or displays the message Found New Hardware. Found New Hardware Wizard  Select “No, not this time” option in Found New Hardware Wizard and click Next if your PC pops up the following Found New Hardware Wizard.    Select “Install the software automatically (Recommended)” option in Found New Hardware Wizard and click Next if your PC pops up the following Found New Hardware Wizard.
 Click Continue Anyway icon in Software Installation Logo testing window    Click Finish icon in Found New Hardware Wizard window   Verify COM Port Address   User can verify installed COM Port in Device Manager
Vista and Windows 7 WARNING:  DO NOT CONNECT KDC TO USB PORT PRIOR TO INSTALLATION 1.  Insert KoamTac Installation CD into your computer’s CD drive.   2. Click Start icon then My Computer icon.  A listing of devices on your computer will be displayed including the disk drive containing the KoamTac Installation CD.   3.  Click on the KoamTac Installation CD icon then click on the Setup directory.  Click on the PC_Setup.exe file which executes the KTSync Setup Wizard.   NOTES    If KTSync Setup Wizard locates an older version of KTSync on your computer, you will be prompted to remove the older program before installing the new version.  Select Remove KTSync then click Finish.  When removal is complete, click Close.  Go to Step 2 to run KTSync Setup Wizard.     If you have any problems, please refer to the Manual Installation section.    KTSync Setup Wizard Below are the screen images you will see during the installation of KTSync.     Click Next icon in KTSync Setup Wizard window
 Click Next icon in KTSync Confirm Installation window     Click Close icon in KTSync Installation Complete window and wait for Device Driver Installation Wizard     Click Install this driver software anyway in Windows Security window
 Click Finish icon in Device Driver Installation Wizard window   Connect KDC to Computer Using the USB cable included with the KDC, follow the directions below.  Connect ultra mini USB connector to the KDC.  Connect Type A USB connector to your PC.  Wait until your computer beeps and/or displays the message Found New Hardware.  Verify COM Port Address   User can verify installed COM Port in Device Manager
Windows Mobile 5.0+  WARNING:  PLEASE CONNECT PDA TO PC PRIOR TO INSTALLATION  1. PC_Setup.exe creates Mobile_Setup.exe file under C:\Program Files\KoamTac\KTSync\Windows.Mobile directory 2. Execute Mobile_Setup.exe   Select Windows Mobile version to install.      Click Next icon.
 Click OK icon in Pending Application Install window     Follow the instructions on PDA screen  COM port Assignment   User should assign a COM port for KDC before using pKTSync.  User should pair KDC with PDA using PDA Bluetooth manager and assign a COM port for Bluetooth communication  Please refer to the PDA manual for the details of COM port assignment method
Android    Download and install aKTSync from the Android Market. http://www.androidzoom.com/android_applications/productivity/ktsync_luxv.html  Blackberry    Download and install bKTSync from the Blackberry App World. http://appworld.blackberry.com/webstore/content/16861?lang=en  iPad/iPhone/iPod touch    Download and install iKTSync from the Apple App Store. http://itunes.apple.com/us/app/ktsync/id372916602?mt=8
2.2 Manual Installation  NOTE:  If you have the KDC100, it has two ports, Ultra Mini and standard Type A which swings out. See Figure 2 for more details.   Windows XP, Vista, and 7 1.  Insert the KoamTac Installation CD into your computer’s disk drive.   2.  Create a directory called KoamTac on your computer. 3.  Copy XP.Vista.7 directory from KoamTac CD to KoamTac directory. The XP.Vista.7 directory contains KTSync® programs for Microsoft® Windows XP, Vista, Windows 7 and user manuals. 4.  Connect KDC cable to ultra mini USB connector on the KDC. 5.  Connect KDC cable to Type A USB connector on your computer. Wait until your computer beeps and/or displays the message New Hardware Found. You will be prompted to search for a device driver for KDC. 6.  Browse then select KTReader.inf file from the KoamTac directory created in Step 2. Follow screen prompts to continue with the device driver installation.   NOTE:  KTReader.inf is the device driver for 32bit Microsoft® Windows XP, Vista, and Windows 7. If you have a 64bit computer, use KTReader.inf file from XP.Vista.64bit folder in the KoamTac directory. Windows Mobile 5.0+ Please connect your Windows Mobile PDA to your computer before software installation.  Create a directory and name it KoamTac on the PDA.  Copy Mobile5.0_6.0 directory from KoamTac CD to PDA KoamTac directory.  Mobile5.0_6.0 contains KTSync® programs for Microsoft® Windows Pocket PC 2003, Mobile 5.0, Mobile 6.0 Standard, and Mobile6.0 Professional.  It also includes KDC User Manual.
3. OPERATING THE KDC  3.1 Getting Started  Attach Hand Strap to KDC To prevent possible damage to the KDC, we strongly recommend wearing it around your hand by the included hand strap.  Also, please don’t swing KDC by the hand strap because contact with another object may cause it to malfunction or become damaged.  To attach the hand strap: 1.  Fit the thin end of hand strap through the pillar of the KDC. 2.  Loop the thick end of strap through the thin loop 3.  Pull the strap tight to secure   Charge KDC Battery Prior to using the KDC, you must charge its battery.  To charge the battery, follow these directions.  1.  Connect the KDC cable to the ultra mini USB connector on the KDC. 2.  Connect the KDC cable to Type A USB connector on your computer. 3.  Your KDC battery will begin charging. Within a few minutes, two small LEDs on the front panel will illuminate orange.  When the battery is fully charged, the LEDs will illuminate green.        KDC100 KDC200 KDC250/300 2 Hours  2 Hours  4 Hours Table 2 – Approximate Time to Charge KDC Battery
 Press UP and DOWN Scroll Buttons simultaneously to access the KDC menu. Configure KDC The KDC is designed to meet the data collection requirements of many different industries in a variety of dynamic situations.  To perform well in these diverse environments, the KDC is designed to be configured easily and quickly.  But, to perform at its maximum level, the KDC must be configured properly.  Until you are familiar with configuring the KDC, it is recommended that you DO NOT modify the KDC settings.  The KDC can be configured in three different methods which are explained in Section 3.3 – KDC Menus, Chapter 4 –Synchronization, and Appendix C – Special Barcodes.    CONFIGURATION METHODS FOR THE KDC   KDC Menu  KTSync®  Software  Special Barcodes            Figure 4 - Location of Scroll Buttons
3.2 Basics  Reading Barcodes Reading a barcode is simple.  Point the KDC at a barcode and press the scan button. Be sure to point the scan engine at the barcode, not at your face, and make sure to position the light beam on the barcode. If the barcode is scanned successfully, you will hear one beep and the LEDs will illuminate in green.   If the scan was unsuccessful, you will hear two beeps and the LEDs will illuminate in red. If you have problems scanning a barcode, try the following suggestions while pointing the KDC at the barcode and depressing the scan button.  Modify the angle of the KDC in relation to the barcode, making the angle bigger or smaller as needed.  Modify the distance between the barcode and the KDC, moving closer or further away as needed.  Check option settings defined in the KDC menu section and change options as needed.  Check that the barcode’s width does not exceed the light beam’s width and vice versa.   Synchronizing Barcode Data to PC Use the KTSync® program to synchronize barcode data from the KDC to your PC. Please refer to Chapter 4 for details.
3.3 KDC Menus  Top Menu   Sub Menu  Options  KDC410(i) KDC415(i) KDC420(i) KDC425(i) KDC430(i)EAN13  Enabled/Disabled  Enabled Enabled N/A N/A N/A EAN8  Enabled/Disabled  Enabled Enabled N/A N/A N/A UPCA  Enabled/Disabled  Enabled Enabled N/A N/A N/A UPCE  Enabled/Disabled  Enabled Enabled N/A N/A N/A CODE39  Enabled/Disabled  Enabled Enabled N/A N/A N/A ITF14  Enabled/Disabled  Enabled Enabled N/A N/A N/A CODE128  Enabled/Disabled  Enabled Enabled N/A N/A N/A I2of5  Enabled/Disabled  Enabled Enabled N/A N/A N/A CODABAR  Enabled/Disabled  Enabled Enabled N/A N/A N/A GS1-128  Enabled/Disabled  Enabled Enabled N/A N/A N/A CODE93  Enabled/Disabled  Enabled Enabled N/A N/A N/A CODE35  Enabled/Disabled  Enabled Enabled N/A N/A N/A BooklandEAN  Enabled/Disabled  Disabled Disabled N/A N/A N/A EAN13withAddon  Enabled/Disabled  Disabled Disabled N/A N/A N/A EAN8withAddon  Enabled/Disabled  Disabled Disabled N/A N/A N/A UPCAwithAddon  Enabled/Disabled  Disabled Disabled N/A N/A N/A Set Barcodes (410/415)  UPCEwithAddon  Enabled/Disabled  Disabled Disabled N/A N/A N/A 1D Symbology  Codabar  N/A  N/A  Enabled  Enabled  N/A    Code 11  N/A  N/A  Enabled  Enabled  N/A    Code 32  N/A  N/A  Enabled  Enabled  N/A    Code 39  N/A  N/A  Enabled  Enabled  N/A    Code 93  N/A  N/A  Enabled  Enabled  N/A    Code 128  N/A  N/A  Enabled  Enabled  N/A    EAN-8  N/A  N/A  Enabled  Enabled  N/A    EAN-13  N/A  N/A  Enabled  Enabled  N/A    GS1 Composit  N/A  N/A  Enabled  Enabled  N/A    I2of5  N/A  N/A  Enabled  Enabled  N/A    Matrix 2of5  N/A  N/A  Enabled  Enabled  N/A    MSI  N/A  N/A  Enabled  Enabled  N/A    Plessey  N/A  N/A  Enabled  Enabled  N/A    PosiCode  N/A  N/A  Enabled  Enabled  N/A    GS1 Omni  N/A  N/A  Enabled  Enabled  N/A    GS1 Limited  N/A  N/A  Enabled  Enabled  N/A    GS1 Expanded  N/A  N/A  Enabled  Enabled  N/A    S2of5 Ind  N/A  N/A  Enabled  Enabled  N/A    S2of5 IATA  N/A  N/A  Enabled  Enabled  N/A    TCL39  N/A  N/A  Enabled  Enabled  N/A    Telepen  N/A  N/A  Enabled  Enabled  N/A    Trioptic  N/A  N/A  Enabled  Enabled  N/A    UPCA  N/A  N/A  Enabled  Enabled  N/A    UPCE0  N/A  N/A  Enabled  Enabled  N/A Set Barcodes (420/425)    UPCE1  N/A  N/A  Enabled  Enabled  N/A
2D Symbology  AztecCode  N/A  N/A  Enabled  Enabled  N/A    AztecRunes  N/A  N/A  Enabled  Enabled  N/A    CodablockF  N/A  N/A  Enabled  Enabled  N/A    Code16K  N/A  N/A  Enabled  Enabled  N/A    Code49  N/A  N/A  Enabled  Enabled  N/A    DataMatrix  N/A  N/A  Enabled  Enabled  N/A    MaxiCode  N/A  N/A  Enabled  Enabled  N/A    MicroPDF  N/A  N/A  Enabled  Enabled  N/A    PDF417  N/A  N/A  Enabled  Enabled  N/A    QRCode  N/A  N/A  Enabled  Enabled  N/A    HanXin Code  N/A  N/A  Enabled  Enabled  N/A Postal Codes  Postnet  N/A  N/A  Enabled  Enabled  N/A    PlanetCode  N/A  N/A  Enabled  Enabled  N/A    UK Post  N/A  N/A  Enabled  Enabled  N/A    Canada Post  N/A  N/A  Enabled  Enabled  N/A    Kix Post  N/A  N/A  Enabled  Enabled  N/A    Australia Post  N/A  N/A  Enabled  Enabled  N/A    Japan Post  N/A  N/A  Enabled  Enabled  N/A    China Post  N/A  N/A  Enabled  Enabled  N/A    Korea Post  N/A  N/A  Enabled  Enabled  N/A OCR OCR Off N/A N/A Enabled Enable N/A    OCR A  N/A  N/A  Disabled  Disabled  N/A    OCR B  N/A  N/A  Disabled  Disabled  N/A    OCR USC  N/A  N/A  Disabled  Disabled  N/A    OCR MICR  N/A  N/A  Disabled  Disabled  N/A    OCR SEMI  N/A  N/A  Disabled  Disabled  N/A CodaBar_NoStartStopChars  Enabled/Disabled  Disabled Disabled N/A N/A N/A UPCE_as_UPCA  Enabled/Disabled  Disabled Disabled N/A N/A N/A EAN8_as_EAN13  Enabled/Disabled  Disabled Disabled N/A N/A N/A UPCE_as_EAN13  Enabled/Disabled  Disabled Disabled N/A N/A N/A ReturnCheckDigit  Enabled/Disabled  Disabled Disabled N/A N/A N/A VerifyCheckDigit  Enabled/Disabled  Disabled Disabled N/A N/A N/A UPCA_as_EAN13  Enabled/Disabled  Disabled Disabled N/A N/A N/A I2of5_VerifyCheckDigit Enabled/Disabled  Disabled Disabled N/A N/A N/A Code39_VerifyCheckDigit  Enabled/Disabled  Disabled Disabled N/A N/A N/A I2of5_ReturnCheckDigit  Enabled/Disabled  Disabled Disabled N/A N/A N/A Code39_ReturnCheckDigit  Enabled/Disabled  Disabled Disabled N/A N/A N/A UPCE_ReturnCheckDigit  Enabled/Disabled  Enabled Enabled N/A N/A N/A UPCA_ReturnCheckDigit  Enabled/Disabled  Enabled Enabled N/A N/A N/A EAN8_ReturnCheckDigit  Enabled/Disabled  Enabled Enabled N/A N/A N/A Barcode Options (410/415) EAN13_ReturnCheckDigit  Enabled/Disabled  Enabled Enabled N/A N/A N/A Codabar Tx StartStop(Enable/disable) N/A N/A Disabled Disabled N/A    Check Digit(DoNotVerify/VerfyDONotTX/VerifyDoTx)  N/A  N/A DoNotVerify DoNotVerify N/A    Concatenate(Disable/Enable/Required)  N/A  N/A  Enabled  Enabled  N/A Barcode Options (420/425) Code39 Tx StartStop(Enable/disable) N/A N/A Disabled Disabled N/A
   Check Digit(DoNotVerify/VerfyDONotTX/VerifyDoTx)  N/A  N/A DoNotVerify DoNotVerify N/A    Append(Enable/Disable)  N/A  N/A  Disabled  Disabled  N/A    Full ASCII(Enable/Disable)  N/A  N/A  Disabled  Disabled  N/A I2of5  Check Digit(DoNotVerify/VerfyDONotTX/VerifyDoTx)  N/A  N/A DoNotVerify DoNotVerify N/A Code11  Check Digit(2 digits/1 digit)  N/A  N/A  2 digits  2 digits  N/A Code128 Concatenate(Disable/Enable) N/A N/A Disabled Disabled N/A Telepen Output(Original/AIM) N/A N/A AIM AIM N/A UPCA VerifyChkDgt(Enabled/Disabled) N/A N/A Enabled Enabled N/A    NumberSys(Enabled/Disabled)  N/A  N/A  Enabled  Enabled  N/A    2DgtAddenda(Enabled/Disabled)  N/A  N/A  Disabled  Disabled  N/A    5DgtAddenda(Enabled/Disabled)  N/A  N/A  Disabled  Disabled  N/A    Req. Addenda(Enabled/Disabled) N/A  N/A Disabled Disabled N/A    Sep. Addenda(Enabled/Disabled)  N/A  N/A  Enabled  Enabled  N/A    Coupon Code(Enabled/Disabled)  N/A  N/A  Enabled  Enabled  N/A UPCE Expand(Enabled/Disabled) N/A N/A Disabled Disabled N/A    Req. Addenda(Enabled/Disabled) N/A  N/A Disabled Disabled N/A    Sep. Addenda(Enabled/Disabled)  N/A  N/A  Enabled  Enabled  N/A    Check Digit(Enabled/Disabled)  N/A  N/A  Enabled  Enabled  N/A    NumberSys(Enabled/Disabled)  N/A  N/A  Enabled  Enabled  N/A    2DgtAddenda(Enabled/Disabled)  N/A  N/A  Disabled  Disabled  N/A    5DgtAddenda(Enabled/Disabled)  N/A  N/A  Disabled  Disabled  N/A EAN-13 VerifyChkDgt(Enabled/Disabled) N/A N/A Enabled Enabled N/A    2DgtAddenda(Enabled/Disabled)  N/A  N/A  Disabled  Disabled  N/A    5DgtAddenda(Enabled/Disabled)  N/A  N/A  Disabled  Disabled  N/A    Req. Addenda(Enabled/Disabled) N/A  N/A Disabled Disabled N/A    Sep. Addenda(Enabled/Disabled)  N/A  N/A  Enabled  Enabled  N/A    ISBN Trans.(Enabled/Disabled)  N/A  N/A  Disabled  Disabled  N/A EAN-8 VerifyChkDgt(Enabled/Disabled) N/A N/A Enabled Enabled N/A    2DgtAddenda(Enabled/Disabled)  N/A  N/A  Disabled  Disabled  N/A    5DgtAddenda(Enabled/Disabled)  N/A  N/A  Disabled  Disabled  N/A    Req. Addenda(Enabled/Disabled) N/A  N/A Disabled Disabled N/A    Sep. Addenda(Enabled/Disabled)  N/A  N/A  Enabled  Enabled  N/A MSI Tx CheckChar(Enabled/Disabled) N/A N/A Disabled Disabled N/A PosiCode  A and B/A&B LimitedA/A&B LimitedB  N/A  N/A  A&B LimitedB  A&B LimitedB N/A GS1 UPCEAN Ver.(Enabled/Disabled) N/A  N/A Disabled Disabled N/A    GS1 Emulation(No Emulate/GS1 128 Emul/GS1 Emulate)  N/A  N/A  No Emulate  No Emulate  N/A PostNet Tx CheckChar(Enabled/Disabled) N/A  N/A Disabled Disabled N/A
PlanetCode Tx CheckChar(Enabled/Disabled) N/A  N/A Disabled Disabled N/A Scan Angle  Narrow/Wide  Wide Wide N/A N/A N/A Filter  Normal/High  Normal Normal N/A N/A N/A Time Out  .5 seconds to 10 seconds  2 second(s)  2 second(s)  2 second(s)  2 second(s)  N/A Min. Barcode Length  2 to 36 characters  4 chars  4 chars  4 chars  4 chars  N/A Security Level  1 to 4 level  2 level  2 level  N/A  N/A  N/A Image Capture  Enabled/Disabled  N/A  N/A  Disabled  Disabled  N/A Auto Trigger  Enabled/Disabled  Disabled Disabled Disabled Disabled  N/A Reread Delay  Continuous, Short, Medium, Long, Extra Long  Medium Medium Medium Medium  N/A Finger Trigger  Enabled/Disabled  N/A N/A N/A N/A N/A Start Position  N/A N/A N/A N/A N/A No. of Char(s)  N/A N/A N/A N/A N/A Scan Options Partial Display Action  N/A N/A N/A N/A N/A Wedge Only              Default Wedge & Store Always  Default  Default Default Default    Store Only                Save if Sent                Wedge / Store Save if Not Sent                Barcode only  Default Default Default Default  N/A Data Format Packet Data                Data Editor/Prefix  Delete  Delete Delete Delete Delete  N/A Data Editor/Suffix  Delete  Delete Delete Delete Delete  N/A Data Editor/AIM ID  None/In Prefix/In Suffix  None  None  None  None  N/A Data Editor/Partial Data  Start Position  1 1 1 1 N/A    No. of Char(s)  0 chars  0 chars  0 chars  0 chars  N/A    Action  Select Select Select Select  N/A Handshake  Enabled/Disabled  Disabled Disabled Disabled Disabled  N/A Terminator  None, CR, LF, CR+LF, Tab Right/Left/Down/Up Arrow  CR+LF CR+LF CR+LF CR+LF CR+LF Data Process Chk Duplicate  Enabled/Disabled  Disabled Disabled Disabled Disabled  N/A Power  Enabled/Disabled  N/A N/A N/A N/A N/A Pairing Pairing neighboring Bluetooth devices N/A N/A N/A N/A N/A Auto Connect  Enabled/Disabled  N/A N/A N/A N/A N/A Auto Power On  Enabled/Disabled  N/A N/A N/A N/A N/A Auto Power On/Power Off Time  Disable, 1sec to 10second(s)  N/A N/A N/A N/A N/A Auto Power Off  Enabled/Disabled  N/A N/A N/A N/A N/A Auto Power Off/Beep Warning  Enabled/Disabled  N/A N/A N/A N/A N/A Auto Power Off/Power Off Time  1 to 30 minutes  N/A N/A N/A N/A N/A PowerOff Msg  Enabled/Disabled  N/A N/A N/A N/A N/A MAC Address  12 Characters Bluetooth MAC Address  N/A N/A N/A N/A N/A BT FW Version  v1.2.xrt Bluetooth Firmware Version  N/A  N/A  N/A  N/A  N/A Discovering  Discovering neighboring Bluetooth devices  N/A N/A N/A N/A N/A Connecting to  View Connect to Bluetooth device  N/A N/A N/A N/A N/A Bluetooth Wakeup Nulls  Enabled/Disabled  N/A N/A N/A N/A N/A BT Config  ConnectDevice  SPP  Default(410) Default(415) Default(420) Default(425) Default(430)
HID iOS                iPhone  Default(410i) Default(415i) Default(420i) Default(425i) Default(430i) SPP2.0                HID normal                Auto Connect  Enabled/Disabled  Disabled Disabled Disabled Disabled Disabled Auto Power On  Enabled/Disabled  Disabled Disabled Disabled Disabled Disabled Auto Power On/Power On Time  Disable, 1sec to 10second(s)  Disabled Disabled Disabled Disabled Disabled Auto Power Off  Enabled/Disabled  Disabled Disabled Disabled Disabled Disabled Auto Power Off/Beep Warning  Enabled/Disabled  Disabled Disabled Disabled Disabled Disabled Auto Power Off/Power Off Time  1 to 30 minutes  5 minutes  5 minutes 5 minutes 5 minutes 5 minutes PowerOff Msg  Enabled/Disabled  Disabled Disabled Disabled Disabled Disabled MAC Address  12 Characters Bluetooth MAC Address  N/A N/A N/A N/A N/A BT FW Version  v1.2.xrt Bluetooth Firmware Version  N/A  N/A  N/A  N/A  N/A Wakeup Nulls  Enabled/Disabled  Disabled Disabled Disabled Disabled Disabled BT Toggle     Enabled Enabled Enabled Enabled Enabled HID AutoLock  Disabled,1,2,3,4,5,10,15 minutes  1 minutes  1 minutes  1 minutes  1 minutes  1 minutes HID Keyboard US,German,French,Italian,Spanish US US US US US HID Delay/Initial  Disabled, 1,2,3,5,10 secs  Disabled Disabled Disabled Disabled Disabled HID Delay/Inter char  Disabled,10, 20, 30, 50, 100msec  Disabled  Disabled  Disabled  Disabled  Disabled HID Ctrl Char  Disabled, Alt+Numpad, ^+Character Disabled Disabled Disabled Disabled Disabled Power  Enabled/Disabled  Enabled Enabled Enabled Enabled Enabled Pairing  Pairing neighboring Bluetooth devices                Discovering  Discovering neighboring Bluetooth devices  N/A N/A N/A N/A N/A Connecting to  View Connect to Bluetooth device  N/A N/A N/A N/A N/A BT Service HID Sync                   Memory Size(3.0 only) 0.5/3.5, 1/3, 2/2, 3/1, 4/0  N/A  N/A  N/A  N/A  N/A No. of Stored Barcodes   N/A N/A N/A N/A N/A Memory Status Free Memory Available  N/A N/A N/A N/A N/A Memory(Empties Data)                Application Memory  N/A N/A N/A N/A N/A Reset Memory BT Registry(KDC100 Not use) N/A N/A N/A N/A N/A Auto Erase  Enabled/Disabled  Disable Disable Disable Disable Disable Sleep Timeout  Disable, 1sec to 10minute(s)  5 second(s)  5 second(s)  5 second(s)  5 second(s)  5 second(s) YYYY:MM:DD &  N/A N/A N/A N/A N/A Date / Time HH:MM:SS  N/A N/A N/A N/A N/A Battery  % of Battery Charge Available  N/A  N/A  N/A  N/A  N/A Version  Firmware Version & Serial No. N/A N/A N/A N/A N/A Button Lock  Enabled/Disabled  Disabled Disabled Disabled Disabled Disabled Beep Sound  Enabled/Disabled  Enabled Enabled Enabled Enabled Enabled Beep Volume  Low/High  Low Low Low Low Low Auto Exit  Enabled/Disabled  N/A N/A N/A N/A N/A Port Status  Enabled/Disabled  N/A N/A N/A N/A N/A System  Config Display Format  Time & Battery / Type & Time / Type & Battery / Memory Status / GPS Data(KDC250 only)/Barcode Only  N/A N/A N/A N/A N/A
Menu Barcode  Enabled/Disabled  N/A  N/A  Disabled  Disabled  N/A Scrolling  Enabled/Disabled  N/A N/A N/A N/A N/A Brightness  1 to 15 level(8 level)  N/A N/A N/A N/A N/A Factory Default  Restores Default Settings                MSR Data Only  Default  Default Default Default  N/A Data Format Packet Data                Track Separator     N/A CR+LF N/A CR+LF CR+LF Use Track1     N/A  Yes  N/A  Yes  Yes Use Track2     N/A  Yes  N/A  Yes  Yes Use Track3     N/A  Yes  N/A  Yes  Yes Beep on error reading Enabled/Disabled  N/A  Disabled  N/A  Disabled  Disabled MSR Config Encryption Enabled/Disabled N/A Enabled N/A Disabled Disabled Table 3 - KDC Menu Options

Navigation menu