AISOLUTION KDC400 Barcode Scanner(Bluetooth) User Manual Appendix G KDC400

AISOLUTION CO., LTD. Barcode Scanner(Bluetooth) Appendix G KDC400

Users Manual

Download: AISOLUTION KDC400 Barcode Scanner(Bluetooth) User Manual Appendix G KDC400
Mirror Download [FCC.gov]AISOLUTION KDC400 Barcode Scanner(Bluetooth) User Manual Appendix G KDC400
Document ID1580825
Application IDZoRHHDCMve27hJmh7KhjQA==
Document DescriptionUsers Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize72.71kB (908819 bits)
Date Submitted2011-11-14 00:00:00
Date Available2011-11-14 00:00:00
Creation Date2017-11-03 07:42:22
Producing SoftwareGPL Ghostscript 9.18
Document Lastmod2017-11-03 07:42:22
Document TitleMicrosoft Word - Appendix-G User Manual_KDC400.doc
Document CreatorPScript5.dll Version 5.2.2
Document Author: ghyoo

KDC400 User Manual
November, 2011
COPYRIGHT, LICENSE, and WARNING PAGE
Copyright 2011 by KoamTac, Inc. All rights reserved.
No part of this publication may be reproduced or used in any form, or by any electrical or mechanical
means, without permission in writing from KoamTac, Inc. The material in this manual is subject to change
without notices. KoamTac reserves the right to make changes to any product to improve reliability,
function, or design. KoamTac doesn’t assume any product liability arising out of, or in connection with,
the application or use of any product, circuit, or application described herein. Follow all warnings and
instructions marked on manual and units. Use only the power source specified in this manual or marked
on the units.
May be covered under one or more pending and/or US Patents, including US Pat. No. 7,769,917;
7,954,710.
KDC® is a registered trademark and property of KoamTac, Inc.
KoamTac® is a registered trademark and property of KoamTac, Inc.
KTSync® is a registered trademark and property of KoamTac, Inc.
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO ANY TYPE OF MOISTURE. DO
NOT LOOK DIRECTLY INTO LASER OR POINT THE LASER INTO ANOTHER PERSON’S EYES. EXPOSURE
TO THE BEAM MAY CAUSE EYE DAMAGE.
CAUTION:
Changes or modifications not expressly approved by the manufacturer responsible for compliance could
void the user’s authority to operate the equipment.
WARNING:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
INFORMATION TO USER:
This equipment has been tested and found to comply with the limit of a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation; if this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user, is encouraged to try to correct the
interference by one or more of the following measures:
1. Reorient / Relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit difference from
that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
WARNING: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
1 . I N T RODU CT I ON
Congratulations on purchasing KoamTac’s revolutionary barcode scanner and data collector.
Lightweight and compact, with a user-friendly design and superior functionality, KoamTac’s KDC works
in a variety of portable applications. Use it independently or as an accessory to your PC, PDA, or
smartphone. To find out more about KoamTac, Inc. and our family of products, visit us at
www.koamtac.com.
FEATURES
KDC100
KDC200
KDC250
KDC300
KDC400
RECHARGEABLE BATTERY
YES
YES
YES
YES
YES
SCAN ENGINE
Laser
Laser
Laser
Imager
Laser/
Imager
AUTOMATIC DATA UPLOAD
YES
YES
YES
YES
YES
STORES10,000+ BARCODES
YES
YES
YES
YES
No
®
KTSYNC SOFTWARE
YES
YES
YES
YES
YES
SDK FOR DEVELOPERS
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
NO
YES
YES
YES
YES
NO
YES
YES
YES
YES
NO
NO
YES
NO
NO
USB CONNECTIONS
©
SUPPORTS MICROSOFT
WINDOWS XP, VISTA, 7 &
MOBILE 5.0+
ANDROID,
IOS
BLACKBERRY,
BLUETOOTH
GPS
Table 1 - Features of KDC
1 .1 K DC Pa c k a ge
The standard KDC package contains:
1. One KDC Barcode Data Collector
2. One USB Cable
3. One Lanyard (KDC100/200/250/300) or One Hand Strap (KDC400)
4. KoamTac Installation CD with

KTSync© for Microsoft Windows XP, Vista, 7 and Mobile 5.0+

KDC Device Driver

User Manual
5. One Protective KDC Rubber Case (KDC100/200/250/300) or One Smartphone Protective
Rubber Case (KDC400)
NOTE: Depending on your region or distributor, package contents may vary.
KDC100/200/250/300
KDC400
Figure 1 – KDC Package
1 .2 K DC Cha ra c t e rist ic s
Before you use your KDC, please become familiar with its physical characteristics. Refer to Figure 2 and
Figure 3 below which indicate placement of scan and scroll buttons, OLED display, LEDs, and ports on
your KDC. All KDC models are similar except for the KDC100 which includes an additional USB
connector.
KDC100 Barcode Reader and Data Collector
Figure 2 - Characteristics of KDC100
KDC200 / KDC250 / KDC300
Barcode Reader and Data Collector
KDC200
KDC250/300
KDC400
Figure 3 - Characteristics of KDC200 / KDC250 / KDC300
2 . I N STALLAT I ON
2 .1 K oa m T a c I nst a lla t ion Wiza rd
Window s X P
WARNING: DO NOT CONNECT KDC TO USB PORT PRIOR TO INSTALLATION
1. Insert KoamTac Installation CD into your computer’s CD drive.
2. Click Start icon then My Computer icon. A listing of devices on your computer will be displayed
including the disk drive containing the KoamTac Installation CD.
3. Click on the KoamTac Installation CD icon then click on the Setup directory. Click on the
PC_Setup.exe file which executes the KTSync Setup Wizard.
NOTES

If KTSync Setup Wizard locates an older version of KTSync on your computer, you will be
prompted to remove the older program before installing the new version. Select Remove
KTSync then click Finish. When removal is complete, click Close. Go to Step 2 to run KTSync
Setup Wizard.

If you have any problems, please refer to the Manual Installation section.
KTSync Setup Wizard
Below are the screen images you will see during the installation of KTSync.

Click Next icon in KTSync Setup Wizard window


Click Next icon in KTSync Confirm Installation window
Within a few minutes, installation of KTSync will be complete. Click Close icon and wait for the
Device Driver Installation Wizard to load.
Device Driver Installation Wizard
Below are the screen images you will see during the installation of the KDC Device Driver.

Click Next icon in Device Driver Installation Wizard window

Click Continue Anyway icon in Software Installation Logo testing window

Click Finish icon in Device Driver Installation Wizard window
Connect KDC to Computer
Using the USB cable included with the KDC, follow the directions below.

Connect the cable’s ultra mini USB connector to the KDC.

Connect the cable’s Type A USB connector to your PC.

Wait until your computer beeps and/or displays the message Found New Hardware.
Found New Hardware Wizard

Select “No, not this time” option in Found New Hardware Wizard and click Next if your PC pops
up the following Found New Hardware Wizard.

Select “Install the software automatically (Recommended)” option in Found New Hardware
Wizard and click Next if your PC pops up the following Found New Hardware Wizard.

Click Continue Anyway icon in Software Installation Logo testing window

Click Finish icon in Found New Hardware Wizard window
Verify COM Port Address

User can verify installed COM Port in Device Manager
V ist a a nd Window s 7
WARNING: DO NOT CONNECT KDC TO USB PORT PRIOR TO INSTALLATION
1. Insert KoamTac Installation CD into your computer’s CD drive.
2. Click Start icon then My Computer icon. A listing of devices on your computer will be displayed
including the disk drive containing the KoamTac Installation CD.
3. Click on the KoamTac Installation CD icon then click on the Setup directory. Click on the
PC_Setup.exe file which executes the KTSync Setup Wizard.
NOTES

If KTSync Setup Wizard locates an older version of KTSync on your computer, you will be
prompted to remove the older program before installing the new version. Select Remove
KTSync then click Finish. When removal is complete, click Close. Go to Step 2 to run KTSync
Setup Wizard.

If you have any problems, please refer to the Manual Installation section.
KTSync Setup Wizard
Below are the screen images you will see during the installation of KTSync.

Click Next icon in KTSync Setup Wizard window

Click Next icon in KTSync Confirm Installation window

Click Close icon in KTSync Installation Complete window and wait for Device Driver Installation
Wizard

Click Install this driver software anyway in Windows Security window

Click Finish icon in Device Driver Installation Wizard window
Connect KDC to Computer
Using the USB cable included with the KDC, follow the directions below.

Connect ultra mini USB connector to the KDC.

Connect Type A USB connector to your PC.

Wait until your computer beeps and/or displays the message Found New Hardware.
Verify COM Port Address

User can verify installed COM Port in Device Manager
Window s M obile 5 .0 +
WARNING: PLEASE CONNECT PDA TO PC PRIOR TO INSTALLATION
1. PC_Setup.exe creates Mobile_Setup.exe file under C:\Program Files\KoamTac\KTSync\Windows.Mobile
directory
2. Execute Mobile_Setup.exe
 Select Windows Mobile version to install.
 Click Next icon.

Click OK icon in Pending Application Install window

Follow the instructions on PDA screen
COM port Assignment

User should assign a COM port for KDC before using pKTSync.

User should pair KDC with PDA using PDA Bluetooth manager and assign a COM port for
Bluetooth communication

Please refer to the PDA manual for the details of COM port assignment method
Android
 Download and install aKTSync from the Android Market.
http://www.androidzoom.com/android_applications/productivity/ktsync_luxv.html
Bla c k be rry
 Download and install bKTSync from the Blackberry App World.
http://appworld.blackberry.com/webstore/content/16861?lang=en
iPa d/iPhone /iPod t ouc h
 Download and install iKTSync from the Apple App Store.
http://itunes.apple.com/us/app/ktsync/id372916602?mt=8
2 .2 M a nua l I nst a lla t ion
NOTE: If you have the KDC100, it has two ports, Ultra Mini and standard Type A which swings
out. See Figure 2 for more details.
Window s X P, V ist a , a nd 7
1. Insert the KoamTac Installation CD into your computer’s disk drive.
2. Create a directory called KoamTac on your computer.
3. Copy XP.Vista.7 directory from KoamTac CD to KoamTac directory. The XP.Vista.7 directory
contains KTSync® programs for Microsoft® Windows XP, Vista, Windows 7 and user
manuals.
4. Connect KDC cable to ultra mini USB connector on the KDC.
5. Connect KDC cable to Type A USB connector on your computer. Wait until your computer
beeps and/or displays the message New Hardware Found. You will be prompted to search
for a device driver for KDC.
6. Browse then select KTReader.inf file from the KoamTac directory created in Step 2. Follow
screen prompts to continue with the device driver installation.
NOTE: KTReader.inf is the device driver for 32bit Microsoft® Windows XP, Vista, and
Windows 7. If you have a 64bit computer, use KTReader.inf file from XP.Vista.64bit folder
in the KoamTac directory.
Window s M obile 5 .0 +
Please connect your Windows Mobile PDA to your computer before software installation.

Create a directory and name it KoamTac on the PDA.

Copy Mobile5.0_6.0 directory from KoamTac CD to PDA KoamTac directory.

Mobile5.0_6.0 contains KTSync® programs for Microsoft® Windows Pocket PC 2003, Mobile
5.0, Mobile 6.0 Standard, and Mobile6.0 Professional. It also includes KDC User Manual.
3 . OPERAT I N G T H E K DC
3 .1 Ge t t ing St a rt e d
At t a c h H a nd St ra p t o K DC
To prevent possible damage to the KDC, we strongly recommend wearing it around your hand by the
included hand strap. Also, please don’t swing KDC by the hand strap because contact with another
object may cause it to malfunction or become damaged.
To attach the hand strap:
1. Fit the thin end of hand strap through the pillar of the KDC.
2. Loop the thick end of strap through the thin loop
3. Pull the strap tight to secure
Cha rge K DC Ba t t e ry
Prior to using the KDC, you must charge its battery. To charge the battery, follow these directions.
1. Connect the KDC cable to the ultra mini USB connector on the KDC.
2.
Connect the KDC cable to Type A USB connector on your computer.
3. Your KDC battery will begin charging. Within a few minutes, two small LEDs on the front panel will
illuminate orange. When the battery is fully charged, the LEDs will illuminate green.
KDC100
KDC200
KDC250/300
2 Hours
2 Hours
4 Hours
Table 2 – Approximate Time to Charge KDC Battery
Configure K DC
The KDC is designed to meet the data collection requirements of many different industries in a variety of
dynamic situations. To perform well in these diverse environments, the KDC is designed to be
configured easily and quickly. But, to perform at its maximum level, the KDC must be configured
properly. Until you are familiar with configuring the KDC, it is recommended that you DO NOT modify the
KDC settings. The KDC can be configured in three different methods which are explained in Section 3.3
– KDC Menus, Chapter 4 –Synchronization, and Appendix C – Special Barcodes.
CONFIGURATION METHODS FOR THE KDC

KDC Menu

KTSync® Software

Special Barcodes
Press UP and DOWN Scroll Buttons
simultaneously to access the KDC
menu.
Figure 4 - Location of Scroll Buttons
3 .2 Ba sic s
Re a ding Ba rc ode s
Reading a barcode is simple. Point the KDC at a barcode and press the scan button. Be sure to point
the scan engine at the barcode, not at your face, and make sure to position the light beam on the
barcode. If the barcode is scanned successfully, you will hear one beep and the LEDs will illuminate in
green.
If the scan was unsuccessful, you will hear two beeps and the LEDs will illuminate in red. If you have
problems scanning a barcode, try the following suggestions while pointing the KDC at the barcode and
depressing the scan button.

Modify the angle of the KDC in relation to the barcode, making the angle bigger or smaller as needed.

Modify the distance between the barcode and the KDC, moving closer or further away as needed.

Check option settings defined in the KDC menu section and change options as needed.

Check that the barcode’s width does not exceed the light beam’s width and vice versa.
Sync hronizing Ba rc ode Da t a t o PC
Use the KTSync® program to synchronize barcode data from the KDC to your PC. Please refer to
Chapter 4 for details.
3 .3 K DC M e nus
Top
Menu
Set
Barcodes
(410/415)
Set
Barcodes
(420/425)
Sub Menu
Options
KDC410(i)
KDC415(i)
KDC420(i)
KDC425(i)
KDC430(i)
EAN13
Enabled/Disabled
Enabled
Enabled
N/A
N/A
N/A
EAN8
Enabled/Disabled
Enabled
Enabled
N/A
N/A
N/A
UPCA
Enabled/Disabled
Enabled
Enabled
N/A
N/A
N/A
UPCE
Enabled/Disabled
Enabled
Enabled
N/A
N/A
N/A
CODE39
Enabled/Disabled
Enabled
Enabled
N/A
N/A
N/A
ITF14
Enabled/Disabled
Enabled
Enabled
N/A
N/A
N/A
CODE128
Enabled/Disabled
Enabled
Enabled
N/A
N/A
N/A
I2of5
Enabled/Disabled
Enabled
Enabled
N/A
N/A
N/A
CODABAR
Enabled/Disabled
Enabled
Enabled
N/A
N/A
N/A
GS1-128
Enabled/Disabled
Enabled
Enabled
N/A
N/A
N/A
CODE93
Enabled/Disabled
Enabled
Enabled
N/A
N/A
N/A
CODE35
Enabled/Disabled
Enabled
Enabled
N/A
N/A
N/A
BooklandEAN
Enabled/Disabled
Disabled
Disabled
N/A
N/A
N/A
EAN13withAddon
Enabled/Disabled
Disabled
Disabled
N/A
N/A
N/A
EAN8withAddon
Enabled/Disabled
Disabled
Disabled
N/A
N/A
N/A
UPCAwithAddon
Enabled/Disabled
Disabled
Disabled
N/A
N/A
N/A
UPCEwithAddon
Enabled/Disabled
Disabled
Disabled
N/A
N/A
N/A
1D Symbology
Codabar
N/A
N/A
Enabled
Enabled
N/A
Code 11
N/A
N/A
Enabled
Enabled
N/A
Code 32
N/A
N/A
Enabled
Enabled
N/A
Code 39
N/A
N/A
Enabled
Enabled
N/A
Code 93
N/A
N/A
Enabled
Enabled
N/A
Code 128
N/A
N/A
Enabled
Enabled
N/A
EAN-8
N/A
N/A
Enabled
Enabled
N/A
EAN-13
N/A
N/A
Enabled
Enabled
N/A
GS1 Composit
N/A
N/A
Enabled
Enabled
N/A
I2of5
N/A
N/A
Enabled
Enabled
N/A
Matrix 2of5
N/A
N/A
Enabled
Enabled
N/A
MSI
N/A
N/A
Enabled
Enabled
N/A
Plessey
N/A
N/A
Enabled
Enabled
N/A
PosiCode
N/A
N/A
Enabled
Enabled
N/A
GS1 Omni
N/A
N/A
Enabled
Enabled
N/A
GS1 Limited
N/A
N/A
Enabled
Enabled
N/A
GS1 Expanded
N/A
N/A
Enabled
Enabled
N/A
S2of5 Ind
N/A
N/A
Enabled
Enabled
N/A
S2of5 IATA
N/A
N/A
Enabled
Enabled
N/A
TCL39
N/A
N/A
Enabled
Enabled
N/A
Telepen
N/A
N/A
Enabled
Enabled
N/A
Trioptic
N/A
N/A
Enabled
Enabled
N/A
UPCA
N/A
N/A
Enabled
Enabled
N/A
UPCE0
N/A
N/A
Enabled
Enabled
N/A
UPCE1
N/A
N/A
Enabled
Enabled
N/A
2D Symbology
AztecCode
N/A
N/A
Enabled
Enabled
N/A
AztecRunes
N/A
N/A
Enabled
Enabled
N/A
CodablockF
N/A
N/A
Enabled
Enabled
N/A
Code16K
N/A
N/A
Enabled
Enabled
N/A
Code49
N/A
N/A
Enabled
Enabled
N/A
DataMatrix
N/A
N/A
Enabled
Enabled
N/A
MaxiCode
N/A
N/A
Enabled
Enabled
N/A
MicroPDF
N/A
N/A
Enabled
Enabled
N/A
PDF417
N/A
N/A
Enabled
Enabled
N/A
QRCode
N/A
N/A
Enabled
Enabled
N/A
HanXin Code
N/A
N/A
Enabled
Enabled
N/A
Postnet
N/A
N/A
Enabled
Enabled
N/A
PlanetCode
N/A
N/A
Enabled
Enabled
N/A
UK Post
N/A
N/A
Enabled
Enabled
N/A
Canada Post
N/A
N/A
Enabled
Enabled
N/A
Kix Post
N/A
N/A
Enabled
Enabled
N/A
Australia Post
N/A
N/A
Enabled
Enabled
N/A
Japan Post
N/A
N/A
Enabled
Enabled
N/A
China Post
N/A
N/A
Enabled
Enabled
N/A
Korea Post
N/A
N/A
Enabled
Enabled
N/A
OCR Off
N/A
N/A
Enabled
Enable
N/A
OCR A
N/A
N/A
Disabled
Disabled
N/A
OCR B
N/A
N/A
Disabled
Disabled
N/A
OCR USC
N/A
N/A
Disabled
Disabled
N/A
OCR MICR
N/A
N/A
Disabled
Disabled
N/A
OCR SEMI
N/A
N/A
Disabled
Disabled
N/A
CodaBar_NoStartStop
Chars
Enabled/Disabled
Disabled
Disabled
N/A
N/A
N/A
UPCE_as_UPCA
Enabled/Disabled
Disabled
Disabled
N/A
N/A
N/A
EAN8_as_EAN13
Enabled/Disabled
Disabled
Disabled
N/A
N/A
N/A
UPCE_as_EAN13
Enabled/Disabled
Disabled
Disabled
N/A
N/A
N/A
ReturnCheckDigit
Enabled/Disabled
Disabled
Disabled
N/A
N/A
N/A
VerifyCheckDigit
Enabled/Disabled
Disabled
Disabled
N/A
N/A
N/A
UPCA_as_EAN13
Enabled/Disabled
Disabled
Disabled
N/A
N/A
N/A
I2of5_VerifyCheckDigit
Enabled/Disabled
Disabled
Disabled
N/A
N/A
N/A
Code39_VerifyCheckD
igit
Enabled/Disabled
Disabled
Disabled
N/A
N/A
N/A
I2of5_ReturnCheckDig
it
Enabled/Disabled
Disabled
Disabled
N/A
N/A
N/A
Code39_ReturnCheck
Digit
Enabled/Disabled
Disabled
Disabled
N/A
N/A
N/A
UPCE_ReturnCheckDi
git
Enabled/Disabled
Enabled
Enabled
N/A
N/A
N/A
UPCA_ReturnCheckDi
git
Enabled/Disabled
Enabled
Enabled
N/A
N/A
N/A
EAN8_ReturnCheckDi
git
Enabled/Disabled
Enabled
Enabled
N/A
N/A
N/A
EAN13_ReturnCheck
Digit
Enabled/Disabled
Enabled
Enabled
N/A
N/A
N/A
Codabar
Tx StartStop(Enable/disable)
N/A
N/A
Disabled
Disabled
N/A
Check
Digit(DoNotVerify/VerfyDONotTX/Verify
DoTx)
N/A
N/A
DoNotVerify
DoNotVerify
N/A
Concatenate(Disable/Enable/Required)
N/A
N/A
Enabled
Enabled
N/A
Tx StartStop(Enable/disable)
N/A
N/A
Disabled
Disabled
N/A
Postal Codes
OCR
Barcode
Options
(410/415)
Barcode
Options
(420/425)
Code39
Check
Digit(DoNotVerify/VerfyDONotTX/Verify
DoTx)
N/A
N/A
DoNotVerify
DoNotVerify
N/A
Append(Enable/Disable)
N/A
N/A
Disabled
Disabled
N/A
Full ASCII(Enable/Disable)
N/A
N/A
Disabled
Disabled
N/A
I2of5
Check
Digit(DoNotVerify/VerfyDONotTX/Verify
DoTx)
N/A
N/A
DoNotVerify
DoNotVerify
N/A
Code11
Check Digit(2 digits/1 digit)
N/A
N/A
2 digits
2 digits
N/A
Code128
Concatenate(Disable/Enable)
N/A
N/A
Disabled
Disabled
N/A
Telepen
Output(Original/AIM)
N/A
N/A
AIM
AIM
N/A
UPCA
VerifyChkDgt(Enabled/Disabled)
N/A
N/A
Enabled
Enabled
N/A
NumberSys(Enabled/Disabled)
N/A
N/A
Enabled
Enabled
N/A
2DgtAddenda(Enabled/Disabled)
N/A
N/A
Disabled
Disabled
N/A
5DgtAddenda(Enabled/Disabled)
N/A
N/A
Disabled
Disabled
N/A
Req. Addenda(Enabled/Disabled)
N/A
N/A
Disabled
Disabled
N/A
Sep. Addenda(Enabled/Disabled)
N/A
N/A
Enabled
Enabled
N/A
Coupon Code(Enabled/Disabled)
N/A
N/A
Enabled
Enabled
N/A
Expand(Enabled/Disabled)
N/A
N/A
Disabled
Disabled
N/A
Req. Addenda(Enabled/Disabled)
N/A
N/A
Disabled
Disabled
N/A
Sep. Addenda(Enabled/Disabled)
N/A
N/A
Enabled
Enabled
N/A
Check Digit(Enabled/Disabled)
N/A
N/A
Enabled
Enabled
N/A
NumberSys(Enabled/Disabled)
N/A
N/A
Enabled
Enabled
N/A
2DgtAddenda(Enabled/Disabled)
N/A
N/A
Disabled
Disabled
N/A
5DgtAddenda(Enabled/Disabled)
N/A
N/A
Disabled
Disabled
N/A
VerifyChkDgt(Enabled/Disabled)
N/A
N/A
Enabled
Enabled
N/A
2DgtAddenda(Enabled/Disabled)
N/A
N/A
Disabled
Disabled
N/A
5DgtAddenda(Enabled/Disabled)
N/A
N/A
Disabled
Disabled
N/A
Req. Addenda(Enabled/Disabled)
N/A
N/A
Disabled
Disabled
N/A
Sep. Addenda(Enabled/Disabled)
N/A
N/A
Enabled
Enabled
N/A
ISBN Trans.(Enabled/Disabled)
N/A
N/A
Disabled
Disabled
N/A
VerifyChkDgt(Enabled/Disabled)
N/A
N/A
Enabled
Enabled
N/A
2DgtAddenda(Enabled/Disabled)
N/A
N/A
Disabled
Disabled
N/A
5DgtAddenda(Enabled/Disabled)
N/A
N/A
Disabled
Disabled
N/A
Req. Addenda(Enabled/Disabled)
N/A
N/A
Disabled
Disabled
N/A
Sep. Addenda(Enabled/Disabled)
N/A
N/A
Enabled
Enabled
N/A
MSI
Tx CheckChar(Enabled/Disabled)
N/A
N/A
Disabled
Disabled
N/A
PosiCode
A and B/A&B LimitedA/A&B LimitedB
N/A
N/A
A&B LimitedB
A&B LimitedB
N/A
GS1
UPCEAN Ver.(Enabled/Disabled)
N/A
N/A
Disabled
Disabled
N/A
GS1 Emulation(No Emulate/GS1 128
Emul/GS1 Emulate)
N/A
N/A
No Emulate
No Emulate
N/A
Tx CheckChar(Enabled/Disabled)
N/A
N/A
Disabled
Disabled
N/A
UPCE
EAN-13
EAN-8
PostNet
Scan
Options
PlanetCode
Tx CheckChar(Enabled/Disabled)
N/A
N/A
Disabled
Disabled
N/A
Scan Angle
Narrow/Wide
Wide
Wide
N/A
N/A
N/A
Filter
Normal/High
Normal
Normal
N/A
N/A
N/A
Time Out
.5 seconds to 10 seconds
2 second(s)
2 second(s)
2 second(s)
2 second(s)
N/A
Min. Barcode Length
2 to 36 characters
4 chars
4 chars
4 chars
4 chars
N/A
Security Level
1 to 4 level
2 level
2 level
N/A
N/A
N/A
Image Capture
Enabled/Disabled
N/A
N/A
Disabled
Disabled
N/A
Auto Trigger
Enabled/Disabled
Disabled
Disabled
Disabled
Disabled
N/A
Reread Delay
Continuous, Short, Medium, Long, Extra
Long
Medium
Medium
Medium
Medium
N/A
Finger Trigger
Enabled/Disabled
N/A
N/A
N/A
N/A
N/A
Start Position
N/A
N/A
N/A
N/A
N/A
No. of Char(s)
N/A
N/A
N/A
N/A
N/A
Action
N/A
N/A
N/A
N/A
N/A
Partial Display
Wedge Only
Wedge & Store Always
Wedge / Store
Default
Default
Default
Default
Default
Default
Default
Default
Default
N/A
Store Only
Save if Sent
Save if Not Sent
Barcode only
Data Format
Packet Data
Data
Process
Bluetooth
BT Config
Data Editor/Prefix
Delete
Delete
Delete
Delete
Delete
N/A
Data Editor/Suffix
Delete
Delete
Delete
Delete
Delete
N/A
Data Editor/AIM ID
None/In Prefix/In Suffix
None
None
None
None
N/A
Data Editor/Partial
Data
Start Position
N/A
No. of Char(s)
0 chars
0 chars
0 chars
0 chars
N/A
Action
Select
Select
Select
Select
N/A
Handshake
Enabled/Disabled
Disabled
Disabled
Disabled
Disabled
N/A
Terminator
None, CR, LF, CR+LF, Tab
Right/Left/Down/Up Arrow
CR+LF
CR+LF
CR+LF
CR+LF
CR+LF
Chk Duplicate
Enabled/Disabled
Disabled
Disabled
Disabled
Disabled
N/A
Power
Enabled/Disabled
N/A
N/A
N/A
N/A
N/A
Pairing
Pairing neighboring Bluetooth devices
N/A
N/A
N/A
N/A
N/A
Auto Connect
Enabled/Disabled
N/A
N/A
N/A
N/A
N/A
Auto Power On
Enabled/Disabled
N/A
N/A
N/A
N/A
N/A
Auto Power On/Power
Off Time
Disable, 1sec to 10second(s)
N/A
N/A
N/A
N/A
N/A
Auto Power Off
Enabled/Disabled
N/A
N/A
N/A
N/A
N/A
Auto Power Off/Beep
Warning
Enabled/Disabled
N/A
N/A
N/A
N/A
N/A
Auto Power Off/Power
Off Time
1 to 30 minutes
N/A
N/A
N/A
N/A
N/A
PowerOff Msg
Enabled/Disabled
N/A
N/A
N/A
N/A
N/A
MAC Address
12 Characters Bluetooth MAC Address
N/A
N/A
N/A
N/A
N/A
BT FW Version
v1.2.xrt Bluetooth Firmware Version
N/A
N/A
N/A
N/A
N/A
Discovering
Discovering neighboring Bluetooth
devices
N/A
N/A
N/A
N/A
N/A
Connecting to
View Connect to Bluetooth device
N/A
N/A
N/A
N/A
N/A
Wakeup Nulls
Enabled/Disabled
N/A
N/A
N/A
N/A
N/A
ConnectDevice
SPP
Default(410)
Default(415)
Default(420)
Default(425)
Default(430)
HID iOS
iPhone
Default(410i)
Default(415i)
Default(420i)
Default(425i)
Default(430i)
SPP2.0
HID normal
Auto Connect
Enabled/Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Auto Power On
Enabled/Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Auto Power On/Power
On Time
Disable, 1sec to 10second(s)
Disabled
Disabled
Disabled
Disabled
Disabled
Auto Power Off
Enabled/Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Auto Power Off/Beep
Warning
Enabled/Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Auto Power Off/Power
Off Time
1 to 30 minutes
5 minutes
5 minutes
5 minutes
5 minutes
5 minutes
PowerOff Msg
Enabled/Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
MAC Address
12 Characters Bluetooth MAC Address
N/A
N/A
N/A
N/A
N/A
BT FW Version
v1.2.xrt Bluetooth Firmware Version
N/A
N/A
N/A
N/A
N/A
Wakeup Nulls
Enabled/Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Enabled
Enabled
Enabled
Enabled
Enabled
BT Toggle
BT
Service
HID AutoLock
Disabled,1,2,3,4,5,10,15 minutes
1 minutes
1 minutes
1 minutes
1 minutes
1 minutes
HID Keyboard
US,German,French,Italian,Spanish
US
US
US
US
US
HID Delay/Initial
Disabled, 1,2,3,5,10 secs
Disabled
Disabled
Disabled
Disabled
Disabled
HID Delay/Inter char
Disabled,10, 20, 30, 50, 100msec
Disabled
Disabled
Disabled
Disabled
Disabled
HID Ctrl Char
Disabled, Alt+Numpad, ^+Character
Disabled
Disabled
Disabled
Disabled
Disabled
Power
Enabled/Disabled
Enabled
Enabled
Enabled
Enabled
Enabled
Pairing
Pairing neighboring Bluetooth devices
Discovering
Discovering neighboring Bluetooth
devices
N/A
N/A
N/A
N/A
N/A
Connecting to
View Connect to Bluetooth device
N/A
N/A
N/A
N/A
N/A
0.5/3.5, 1/3, 2/2, 3/1, 4/0
N/A
N/A
N/A
N/A
N/A
No. of Stored Barcodes
N/A
N/A
N/A
N/A
N/A
Free Memory Available
N/A
N/A
N/A
N/A
N/A
Application Memory
N/A
N/A
N/A
N/A
N/A
BT Registry(KDC100 Not use)
N/A
N/A
N/A
N/A
N/A
Auto Erase
Enabled/Disabled
Disable
Disable
Disable
Disable
Disable
Sleep Timeout
Disable, 1sec to 10minute(s)
5 second(s)
5 second(s)
5 second(s)
5 second(s)
5 second(s)
YYYY:MM:DD &
N/A
N/A
N/A
N/A
N/A
HH:MM:SS
N/A
N/A
N/A
N/A
N/A
Battery
% of Battery Charge Available
N/A
N/A
N/A
N/A
N/A
Version
Firmware Version & Serial No.
N/A
N/A
N/A
N/A
N/A
Button Lock
Enabled/Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Beep Sound
Enabled/Disabled
Enabled
Enabled
Enabled
Enabled
Enabled
Beep Volume
Low/High
Low
Low
Low
Low
Low
Auto Exit
Enabled/Disabled
N/A
N/A
N/A
N/A
N/A
Port Status
Enabled/Disabled
N/A
N/A
N/A
N/A
N/A
Display Format
Time & Battery / Type & Time / Type &
Battery / Memory Status / GPS
Data(KDC250 only)/Barcode Only
N/A
N/A
N/A
N/A
N/A
HID Sync
System
Config
Memory Size(3.0 only)
Memory Status
Memory(Empties Data)
Reset Memory
Date / Time
Menu Barcode
Enabled/Disabled
N/A
N/A
Disabled
Disabled
N/A
Scrolling
Enabled/Disabled
N/A
N/A
N/A
N/A
N/A
Brightness
1 to 15 level(8 level)
N/A
N/A
N/A
N/A
N/A
Factory Default
Restores Default Settings
Default
Default
Default
Default
N/A
Track Separator
N/A
CR+LF
N/A
CR+LF
CR+LF
Use Track1
N/A
Yes
N/A
Yes
Yes
Use Track2
N/A
Yes
N/A
Yes
Yes
Use Track3
N/A
Yes
N/A
Yes
Yes
MSR Data Only
Data Format
Packet Data
MSR
Config
Beep on error reading
Enabled/Disabled
N/A
Disabled
N/A
Disabled
Disabled
Encryption
Enabled/Disabled
N/A
Enabled
N/A
Disabled
Disabled
Table 3 - KDC Menu Options
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Extract, Print high-res
Author                          : ghyoo
Create Date                     : 2011:11:14 16:24:48+09:00
Modify Date                     : 2011:11:14 16:40:19+09:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Format                          : application/pdf
Creator                         : ghyoo
Title                           : Microsoft Word - Appendix-G User Manual_KDC400.doc
Creator Tool                    : PScript5.dll Version 5.2.2
Metadata Date                   : 2011:11:14 16:40:19+09:00
Producer                        : Acrobat Distiller 9.0.0 (Windows)
Document ID                     : uuid:73e20435-f297-43f1-a34a-ecfc0ee4dbf7
Instance ID                     : uuid:ef351934-418b-43c4-92f1-81df0468dc1c
Page Count                      : 28
EXIF Metadata provided by EXIF.tools
FCC ID Filing: VH9KDC400

Navigation menu