ALE BTMOD02 Bluetooth module User Manual BTDB user s manual
ALE International Bluetooth module BTDB user s manual
ALE >
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3367805 |
| Application ID | 27aMszyXY7/PnJWVK2aM3g== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 90.15kB (1126848 bits) |
| Date Submitted | 2017-04-24 00:00:00 |
| Date Available | 2017-04-24 00:00:00 |
| Creation Date | 2017-04-19 09:33:04 |
| Producing Software | GPL Ghostscript 9.04 |
| Document Lastmod | 2017-04-19 09:33:04 |
| Document Title | BTDB user's manual |
| Document Creator | FreePDF 4.06 - http://shbox.de |
| Document Author: | zhangelliot |
All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel. Table of Content 1. GENERALITIES ............................................................................................................... 2 1.1 INTRODUCTION ............................................................................................................................................. 2 1.1.1 Overview .................................................................................................................................................. 2 1.1.2 Aim of the document................................................................................................................................. 3 1.2 SERVICES PROVIDED BY THE FEATURE OR EQUIPMENT ................................................................................. 3 1.3 EXTERNAL INTERFACES ................................................................................................................................ 3 1.4 TERMINOLOGY / ABBREVIATIONS ................................................................................................................. 5 1.5 RELATED DOCUMENTS ................................................................................................................................. 6 2. GENERAL REQUIREMENTS ........................................................................................ 7 2.1 FEATURES ..................................................................................................................................................... 7 2.2 STANDARDS .................................................................................................................................................. 7 2.2.1 BT related certification ............................................................................................................................ 7 2.3 ENVIRONMENTAL REQUIREMENTS ................................................................................................................ 8 3. GENERAL DESCRIPTION ............................................................................................. 9 3.1 3.2 3.3 3.4 4. BT FUNCTION GLOBAL LOGICAL BLOC DIAGRAM ......................................................................................... 9 BT DAUGHTER BOARD BLOC DIAGRAM......................................................................................................... 9 MECHANICAL ASPECTS AND INTEGRATION ................................................................................................. 10 SPECIFICATION ............................................................................................................................................ 11 DETAILED TECHNICAL DESCRIPTION .................................................................. 12 4.1 ELECTRONIC ............................................................................................................................................... 12 4.1.1 BT chip solution to be implemented ....................................................................................................... 12 4.1.2 Schematic ............................................................................................................................................... 13 4.2 RADIOFREQUENCY...................................................................................................................................... 14 4.2.1 Antenna choice ....................................................................................................................................... 14 4.2.2 Immunity to external spurious and interferences ................................................................................... 15 4.2.3 Quality of supply .................................................................................................................................... 15 4.3 LAYOUT ...................................................................................................................................................... 16 4.3.1 BTDB layout........................................................................................................................................... 16 4.3.2 Place requirements of BTDB on mainboard .......................................................................................... 16 4.4 SOFTWARE .................................................................................................................................................. 16 4.5 CERTIFICATION ........................................................................................................................................... 17 4.5.1 General aspects on the “module” concept ............................................................................................ 17 5. THERMAL MANAGEMENT ........................................................................................ 18 6. RELIABILITY ................................................................................................................ 18 7. INDUSTRIAL CONSIDERATIONS .............................................................................. 18 7.1 MANUFACTURING ....................................................................................................................................... 18 7.2 REQUIREMENTS .......................................................................................................................................... 18 7.3 TESTABILITY ............................................................................................................................................... 18 7.3.1 Testpoints................................................................................................................................................ 18 7.3.2 Test strategy ........................................................................................................................................... 19 7.3.3 Test method............................................................................................................................................. 20 7.4 MECHANICAL ASSEMBLY / INDUSTRIAL FEASIBILITY .................................................................................. 23 7.4.1 Board outline .......................................................................................................................................... 23 7.4.2 Board technology ................................................................................................................................... 23 7.4.3 Connections............................................................................................................................................ 24 7.4.4 Mounting on the main board .................................................................................................................. 24 7.4.5 Shielding Mounting ................................................................................................................................ 26 All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel. Generalities 1.1 Introduction 1.1.1 Overview The main objectives for this board, discussed also with the marketing are: • Get lowest cost solution to enable BT for a maximum of IP terminals • Enable new usages like • The phone is seen as a carkit for a smartphone The phone can exchange phonebook with a smartphone The phone can support tags through BT Low Energy From R&D point of view: The board must be small enough to be integrated easily into our ID. The board must integrate the antenna to avoid a re-certification for each phone which would use it. For this project, a pre-study has been done. See reference [1]. The choice is to do a daughter board with the chip CC2564C from Texas Instruments, with an integrated antenna on the layout (Printed antenna). This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Please note that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage; (2)l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. CAN ICES-3 (B)/NMB-3(B) 1.1.2 Aim of the document A pre-study has been done, in order to define the best choices for the whole solution, going from antenna to the BT management software in the phone. This document is intended to give all the technical inputs in order to make a BT daughter board which will be used on the Alcatel-Lucent IP Phones. A first step will be to use it on 8068s and 8078s, but we should care to make it possible to be used also on nextgen phones and other projects. 1.2 Services provided by the feature or equipment The BTDB will give a BT4.2 connectivity to the product where it is mounted into. The main reasons of this daughter board are to have: • A common function usable on several phones without the need of RF expertise and full BT qualification • A cost effective solution 1.3 External Interfaces The interface signals are listed hereafter: All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel. Pin N° Name GND VDD_IO GND SLOW_CLK GND HCI_RX TX_DBG HCI_CTS 10 GND GND 11 HCI_RTS 12 13 14 15 16 17 HCI_TX GND PCM_SYNC PCM_CLK PCM_OUT PCM_IN 18-23 GND Function Keep feet on the ground. Direct path supply for 1.8V I/O pads. Keep feet on the ground. 32.768KHz +/- 250ppm Keep feet on the ground. HS UART Receive up to 4Mbps TI internal debug messages. Not used. HS UART flow control: data from BTDB to Host allowed when low Keep feet on the ground. Keep feet on the ground. HS UART flow control: data from host to BTDB allowed when low HS UART Transmit up to 4Mbps Keep feet on the ground. Frame synchro for audio data Clock for audio data Output of audio data. Maybe in tristate Input of audio data 24 ENABLE 25 GND Keep feet on the ground. Disables BT chip when low (Pull down) and performs internal reset of CC2564. Minimum low state duration: 5ms Keep feet on the ground. 26 VDD_IN General supply 27 GND Keep feet on the ground. Type Voltage Power Power Power Power I /PU O /PU 0V 1.8V 0V 1.8V 0V 1.8V 1.8V I /PU 1.8V Power Power 0V 0V O /PU* 1.8V O/PU* Power I/O /PD I/O /PD O /PD 1.8V 0V 1.8V 1.8V 1.8V 1.8V Power 0V I /PD 1.8V Power 0V 2.2V-4.8V Power 0V PU* : Pull-Up enabled only during ShutDown and DeepSleep phases (. These correspond to the metal cut-holes. See chapter 7.4.3. The VDD_IN pin can accept 2.2V to 4.8V. Typical value is 2.5V or 3.3V, but this depends on the motherboard. Check the CC2564C datasheet for more information. The UART has by default the following characteristics (can be reprogrammed to up to 4Mbps) All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel. Check the CC2564C datasheet for more information. This cabling supposes that the Host is in DTE mode. In case of DCE host, RTS and CTS are straight, and not crossed. CAUTION: Only the following interfaces are fail safe (can stand an applied voltage when the device interface, or the device is not powered (VDDio or VDDin not provided): AUD_FSYNC, AUD_CLK, AUD_IN, AUD_OUT, SLOW_CLK This means that the motherboard must not apply a voltage on HCI_RX, HCI_TX, HCI_CTS or HCI_RTS pins before the VDDio is supplied. Even when VDDio is present, it is not allowed to ENABLE the chip if VDDin is not present. See specification of CC2564 for more details. The SLOW_CLK source must be stable within 2ms after the ENABLE LOW to HIGH transition. ENABLE Note: FAST CLOCK must be stable within 20ms of nSHUTD(ENABLE) going high. But according to TI FAE’s feedback, the 20ms limit only applies to TCXO. Crystal is used in BTDB, which doesn’t need to follow the 20ms limit. 1.4 Terminology / Abbreviations BTDB: BlueTooth Daughter Board BT: BlueTooth All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel. LE: Low Energy 1.5 Related Documents Document Reference number Alcatel documents [1] Bluetooth: Pre-study of a low cost solution for BT in Desktop Phones 3AK_29000_0041_BEZZA [2] 8088 Hardware external specification 3AK_29000_0080_EDZZA [3] ESD CSBU R&D - PB Design/Layout rules 8AL 51074 0003 DSZZA [4] NOE3G INDUSTRIAL REQUIREMENTS 3BN 69030 1403 MCASA External documents [5] [6] All TI documents for CC2564 (upload) 3AK_29_CC256X_BLUETOOTH_02278 All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel. 2. General Requirements 2.1 Features The board must provide the following features: • Give dual mode BT connectivity (Classic & Low Energy), so BT4.1 • Integrate the antenna, done with copper tracks on the PCB • Interface to the motherboard with UART and PCM, USB not required. • Permit a very low cost solution. • Give ease of re-use for other products (simple process, no RF expertise). 2.2 Standards 2.2.1 BT related certification On the Bluetooth.org website, the existing certifications of BT solutions are listed. The certification strategy will be as follows: • Make a certification for the board, with embedded low part of the BT stack, and antenna • Make a product certification, where the BTDB is in the Phone. Here we can take benefit of the module certification • Following the first product certification (ex: NOE3GEE), the next products which use the BTDB will need minimum or no certification, on condition that the used upper BT stack (in host processor) is the same as the one of NOE3GEE. It is necessary to make a BT qualification for the BTDB with its antenna. This will qualify: • The hardware, radio parts • The Lower part of the BT stack (below HCI interface) located in the BT chip • The Upper part of the BT stack, which runs on the Host processor. This is why, if we re-use this board, a big part of the certification does not need to be done. See chapter 4.5.1 for discussion about the “module” aspect for BT certification. All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel. 2.3 Environmental requirements These are the same as for the terminal for which this board is intended. The tests are made on the daughter board mounted in a final product, so they are part of the product qualification. This BTDB board cannot be co-located with other transmitters. If mount this board on final product, Should add FCC ID and IC information in the product label (FCC ID: OL3BTMOD02, IC: 1737DBTMOD02). For a host manufacture’s using a certified modular, if (1) the module’s FCC ID is not visible when installed in the host, or (2) if the host is marketed so that end users do not have straightforward commonly used methods for access to remove the module so that the FCC ID of the module is visible; then an additional permanent label referring to the enclosed module: “Contains Transmitter Module FCC ID: OL3BTMOD02, IC: 1737D-BTMOD02” or “Contains FCC ID: OL3BTMOD02, Contains IC: 1737D-BTMOD02” must be used. The host OEM user manual must also contain clear instructions on how end users can find and/or access the module and the FCC ID. This equipment complies with radio frequency exposure limits set forth by the Innovation, Science and Economic Development Canada for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 15mm between the device and the user or bystanders. This device must not be co-located or operating in conjunction with any other antenna or transmitter. Cet équipement est conforme aux limites d'exposition aux radiofréquences définies par la Innovation, Sciences et Développement économique Canada pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 15mm de distance entre le dispositif et l'utilisateur ou des tiers. Ce dispositif ne doit pas être utilisé à proximité d’une autre antenne ou d’un autre émetteur. For details see for example the Smart Deskphone 8088 HW external specification (see ref [2]) 3.1 BT function global logical bloc diagram 3.2 BT daughter board bloc diagram 1.8V 2.2V-4.8V 1.8V VDD Vdd I/O LDO_out DC/DC UART UART PCM PCM/I2S 32.768KHz SlowClock GPIO Enable Bandpass filter Crystal 26MHz TI CC2564C < 20ppm Daughter Board PCB 2.4GHz Antenna All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel. 3. General Description All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel. The CC2564C communicates with a standard HCI through the UART interface. Here is a representation of the lower part of the stack, which is inside the CC2564C: This means that the upper part of the stack must be hosted in the mother board cpu. 3.3 Mechanical aspects and integration This board will be mounted on a IP Phone CPU board or BT handset CPU board. For radiofrequency propagation reasons, the antenna area must not cover any copper plane. For industrial reasons, the board must lay on the CPU board on at least 2/3 of it’s surface. Examples of implementation follow: No copper under antenna CPU PCB CPU PCB Another alternative, best is: Copper OK L/3 max CPU PCB CPU PCB All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel. 3.4 Specification Parameter Value Standard support Bluetooth 2.1 + EDR, BLE 4.2 Host interface HCI UART VBAT 1.7 Volts, 4.8 Volts VDD_IO Min, Max 1.62 Volts, 1.92 Volts Temperature range (board) -5 to +65°C Frequency range 2402 MHz to 2480 MHz Transmit power GFSK, and EDR Transmit power BLE +4 dBm typ +6dBm max RX Sensitivity BR Max RX Sensitivity BLE -91.5 dBm, GFSK at 0.1% BER -81 dBm, 8DPSK at 0.01% BER -93 dBm, PER=30.8% Full throughput current 42 mA, GFSK or EDR Max SCO link HV3 15 mA Max Idle current BR and EDR 5 mA Max BLE Scanning 310 uA Max BLE Advertising 150 uA Max Shutdown current 10 uA Max Min, Max RX Sensitivity EDR -6dBm typ -4dBm max Max Max All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel. 4. Detailed Technical Description 4.1 Electronic 4.1.1 BT chip solution to be implemented The chosen chip to implement BT4.2 compliant connectivity is the Texas Instruments CC2564C chip. This is a dual mode (Classic + Low Energy) one chip solution. This chip comes in several versions: • Version A (CC2564A) which is on the market already a while, and for which it is necessary to download a patch to implement mSBC codec. • Version B (CC2564B) which will be in mass production in Q4/2013. It integrates all patches for mSBC and other bug corrections in ROM. • Version C (CC2564C) which is BT4.2 compliant. This chip integrates the baseband, the RF amplifier, balun, and power regulator. It needs externally: • a bandpass filter (SAW filter) + antenna • an accurate 26MHz source (crystal with less than 20ppm initial+ temperature+aging) • a standard slow clock at 32.768KHz for low power modes (100ppm), which will be provided by the CPU • Some passive components. We will implement the reference design from Texas Instrument, with minor adaptation to our needs (no level shifters, or test probe headers…). All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel. 4.1.2 Schematic All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel. 4.2 Radiofrequency 4.2.1 Antenna choice Two major types of antennas could be implemented: • Ceramic antenna: very compact, these are easy to mount, but have a cost of around 13 cents. Their performance is medium. • PCB antenna: this uses a track of copper on the PCB. It gives good performance at 2.4GHz, very low cost, but needs more surface and may need some tuning. The PCB antenna designs are well known. The BTDB will use the PCB antenna. In this type, we have for BT two main choices: • The inverted F antenna, well known, good performance, very low dependence to the environment . It has a large bandwidth. Typical size is 26mm x 8mm. This is too large for our module. • The meandered inverted F antenna, which is a variant to have more compacity: 16mm x 6mm. This one is good for our design. This antenna is sensitive to small dimension changes, and has a narrow bandwidth. So an exact copy of the reference dimensions must be done. This antenna is typically used in BT USB dongle designs. The meandered inverted F antenna will be used for the design. Check the following document for the antenna specification and implementation: http://www.ti.com/litv/pdf/swra117d (also available in doc ref [3]). To improve the antenna efficiency, we changed the antenna shape data as the following figure and table: GND move to feed line 0.59mm (D5, L3), cut antenna 0.80mm (L1). The antenna gain is 5.1dBi. All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel. 4.2.2 Immunity to external spurious and interferences The BT radio can be perturbed by external high amplitude radiofrequency fields. In this case, the BT may show high bit error rate for example. To improve the immunity of the BTDB, we will foresee a soldered shield, for risk mitigation. In our application, there are no nearby emitters (like WIFI or GSM a few centimeters far from the BT radio). Neither TI, nor Broadcom put a shield by default in their implementations. The shield will be the one which is on the reference design (16.5 x 16.5mm), if this is not limiting size reduction. 4.2.3 Quality of supply The radio is sensitive to wideband noise on the power supply. The CC2564 integrates high rejection linear regulators, able to provide a clean supply from typically battery voltage with high voltage dips. Voltage dips are allowed up to 400mV for a duration less than 2.3ms. This means that no special care needs to be taken when feeding the board with 3.3V (on mother board). All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel. An 1.8V feed is provided for the I/O. This is not a sensitive supply and no special care is needed for this in terms of noise (the typical noise level found on digital boards on 1.8V is acceptable). 4.3 Layout 4.3.1 BTDB layout The layout recommendations from Texas Instruments must be followed. Refer to document: http://www.ti.com/lit/an/swra420/swra420.pdf (also available in doc ref [3]). The layout MUST be based on the evaluation kit of TI. The main page for this follows: http://processors.wiki.ti.com/index.php/CC256x 4.3.2 Place requirements of BTDB on mainboard To make the BTDB on mainboard has similar antenna resonant frequency as BTDB alone, there are some BTDB place requirements: 1. The under space of the BTDB antenna need to be empty, at least 5.5mm empty space. 2. The right side of BTDB antenna need to be at least 3mm empty space. 3. The left side of BTDB antenna need to be at least 5mm empty space. 4.4 Software A set of patches and features improvements must be downloaded to the CC2564 chip. This is named as “service pack”. It depends on the device version (A, B or C), and MUST be downloaded when the device is powered up, before any RF usage. All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel. 4.5 Certification 4.5.1 General aspects on the “module” concept This gives some clarifications about the “module” definition given by FCC. Single-modular transmitter has to comply with all eight following requirements: i. The radio elements must have the radio frequency circuitry shielded. Physical components and tuning capacitor(s) may be located external to the shield, but must be on the module assembly; ii. The module must have buffered modulation/data inputs to ensure that the device will comply with Part 15 requirements with any type of input signal; iii. The module must contain power supply regulation on the module; iv. The module must contain a permanently attached antenna, or contain a unique antenna connector, and be marketed and operated only with specific antenna(s), per Sections 15.203, 15.204(b), 15.204(c), 15.212(a), 2.929(b); v. The module must demonstrate compliance in a stand-alone configuration; vi. The module must be labelled with its permanently affixed FCC ID label, or use an electronic display (See KDB Publication 784748 about labelling requirements); vii. The module must comply with all specific rules applicable to the transmitter including all the conditions provided in the integration instructions by the grantee; viii. The module must comply with RF exposure requirements (see discussions below). Single-modular transmitter can demonstrate compliance (EMC, SAR, HAC) independent of the host. Limited single-modular transmitter: Limited single-modular transmitter is a transmitter that does not meet all eight requirements, but may rely on a specific host and applicable operating conditions for compliance. For instance, the shielding, buffered I/O or power regulation may be provided by a specific host. In these cases the module would be “Limited” to the specific host providing those requirements. A modular is designated as “limited” when compliance is demonstrated in a particular product configuration. For example, it may be installed in a specific host for demonstrating compliance for EMC, SAR or HAC requirements. For Limited single- modular transmitter, compliance with EMC, SAR, HAC can only be demonstrated for particular product configurations. Certification must be tested in the particular host. Check the document 996369.pdf from FCC for more details. All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel. 5. Thermal management No thermal issue is foreseen for this board, as power levels are low (about 130mW in EDR full throughput). So no special thermal care must be taken. 6. Reliability It can be calculated with CADRE tool according to the reliability database user guide. http://alda.web.alcatel-lucent.com/transition_docs/CADRE_SR332/SR332-CADRE-main.html Usually the calculation is done within the final product (the phone) 7. Industrial Considerations 7.1 Manufacturing Trimming The radio has an auto-calibration feature. This means that once the radio parameters have been defined by engineering, and stored in the chip, there is no need of trimming in manufacturing. During engineering, care must be taken to define the right RF level output taking into account the losses in the bandpass filter and potential impedance adaptation cells. 7.2 Requirements The module is considered as a component for the manufacturing, and must be stores in a reel, in vacuum packing until is mounted on the mother board. Refer to doc: [3] and [4] for more information 7.3 Testability This proposal is based on a discussion with NPI. This may be refined in a second step. 7.3.1 Testpoints There is no need of having one test-point per trace, as the board will not use ICT. The AOI (automatic vision) test is foreseen to be made before the shield is put on the board, but before the soldering. For the RF track to antenna, there will be a pad in series, in order to disconnect the PCB antenna by cutting the track. The pad will then be used to get the RF signal, and the GND surrounding for the shield. See other IP-Phones CPUs for reference. All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel. This is used during certification where conducted tests are done. The RF test point will be at top side, with the center point on the RF wire. This is TP 8 Cut here for BT certification in conduction Gold plating To Antenna L100 Antenna Matching RF Test point TP 8 Ground plane Note: After the tuning, matching circuits are reduced from PI filter(2 capacitors and 1 resistor) to single 0402 size inductor L100 3nH. 7.3.2 Test strategy The board is simple enough to be tested in functional, without ICT. The other point is that the shield may be mounted, so we have no access to the possible test points under it. On the other PCB side, there must be no test point, as this side is in direct contact with the CPU board. 7.3.2.1 Test of the daughter board alone So the test on the daughter board will be done by functional checks: • Each interface is activated (see chapter 7.3.3) • The RF is checked through a tester antenna (through the air or on the RF testpoint) • Some test points will be available on the bottom side for the integrated power regulators. These tests will validate the solders of components on the daughter board As usual, two tests are done: • Radiated test (with tester antenna) for the RF power which covers emission • Conducted test (the signal is taken on TP8) for BER, which covers reception Remark: the conducted test means that the RF tester is in parallel of the printed antenna, which cannot be disconnected without unsoldering a component (which can’t be done in production). We look for GO/NOGO test and not radio setting. A basic calculation shows that the Voltage Standing Wave Ration (VSWR) will be around 2, which gives a maximum of 9.5dB reflected RF power in worst case. All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel. In consequence, the generated RF signal at the tester must be increased to compensate this. The best reliable solution is to take a golden sample of the board to setup the RF level for conducted BER measurement. This will simplify the procedure in manufacturing. Radiated test: RF power (High level signal) Conducted test: BER (low level signal) Both antenna and tester are connected: mismatch with about 9.5dB reflected power max. 7.3.2.2 Test of the daughter board mounted in a phone For the tests of the BTDB on the mother board, we must consider it as a component. • The connections to the BTDB are checked by functional test of the interfaces • The RF is tested through the air. Only the RF radiated test is done to check: • RF power level • BT connection (for example by pairing a device) 7.3.3 Test method Here is an overview of the means to test the connections within the BTDB. The board can be individually tested (no need of mounting it on the CPU). Many functions of the chip can be driven through UART Vendor Specific commands. The list is given in the following document: http://processors.wiki.ti.com/index.php/CC256x_VS_HCI_Commands (also available in doc ref [3]). Some test method can also be taken from the following page: http://processors.wiki.ti.com/index.php/CC256x_Testing_Guide (also available in doc ref [3]). Before any RF is activated, the Service Pack (SP) must be downloaded to the CC2564C. For manufacturing, this ServicePack will be stored in PDM. It may evolve with time, but the manufacturing tools do not need to have the latest version, because the phone software will have it integrated, and download it at phone start-up. Only if there is an identified but which could impact the manufacturing tests, the SP will be updated. Here is a table that gives examples of tests for each feature: All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel. Function Power and power-up Nbr of connections VDD_IN VDD_IO Slow_CLK Fast_CLK SP download Enable must be LOW. Start VDD_IN, HCI_RTS goes then VDD_IO. Apply Slow Clock. from HIGH to Apply Fast Clock. Make a transition LOW. LOW to HIGH on Enable. On test Point: Pin 11 NA HCI_TX HCI_RX HCI_RTS HCI_CTS Setup the tester UART to 115.2k 8N1, with HW flow control. Read the Local version info (send 0x01 0x01 0x10 0x00). Other commands are available The chip replies with the version. PCM_IN PCM_OUT PCM_FSYNC PCM_CLK Make a loop back of PCM with HCI_VS_Set_Pcm_Loopback_Enabl e (0xFE28) command, and send PCM data to bus SLOW_CLK If this is not provided, no way to boot the device, after enable. The HCI_RTS signal will stay high. HCI_RTS goes from HIGH to LOW. FREFP/FREFN If this is not running, no way to make a communication through UART. If the PCM is put in master mode, the clock is 4096kHz and is based on the Fast_Clk. This permits to measure the precision. UART test is OK. The PCM_CLK generated is at +/- 15ppm. Make a transition LOW to HIGH on Enable, and check the HCI_RTS state HCI_RTS goes from HIGH to LOW. Pin 11 Check state of the test point when the chip is shutdown. Level should be “1” ie close to 1.8V. Pin 7 Not used, no need to test. No test PCM Slow_Clk Fast_Clk Enable nSHUTD Debug TX_DBG Clock request Test OK if The service pack must be downloaded before any RF test is possible. Check testing guide. This patch will be stored in PDM, associated to the board. NA HCI UART Method CLK_REQ_OUT NA The received PCM data is same as sent data Pin 12 Pin 6 Pin 11 Pin 8 Pin 17 Pin 16 Pin 14 Pin 15 Pin 11 Pin 15 NA All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel. Function Nbr of connections Power regulators DIG_LDO_OUT MLDO_OUT SRAM_LDO_OUT ADCPPA_LDO_OUT CL1.5_LDO_OUT DCO_LDO_OUT Power IN VDD_IO CL1.5_LDO_IN MLDO_IN BT RF BT RF BT RF IN RF ANT Method Test OK if The 6 testpoints will be available on the bottom side of the board. Test the value, and the ripple (in AC). Voltages are close to those on a golden sample. If one of these supplies are not available, the BT emission will not pass the test. BT emission is compliant. Check the emitted RF level and frequency with a tester antenna. RF is present and at the right level. Second test for reception (optional): put the chip in continuous reception, emit RF with the tester, and check the level of RSSI with HCI_VS_Read_RSSI (0xFDFC) command On test Point: TP 1 TP 2 TP 3 TP 4 TP 5 TP 6 NA TP 8 RF is received at the right RSSI level. One option could be to use the development kit from TI as test tool, which is composed of: • The CPU board MSP430F5438, connected through USB to a computer • The BTDB which makes the BT function and is connected to the MSP430 CPU Therefore, see the wiki about the test tool available: http://processors.wiki.ti.com/index.php/CC256x_Bluetooth_Hardware_Evaluation_Tool The associated PC software provides the following features; • Configuration download, service pack download • Sleep mode activation • Output power setting • Radio testing through test modes (see below) • Debug Traces monitor The individual test modes are: Test Mode Description Continuous TX BT device continously transmits at a particular frequency, modulation, and power Continuous RX Sets BT device to receive continuously at a particular channel Packet TX/RX BT device continously transmits packets at particular frequency, packet type, etc... BT RF SIG Mode Put the device into Device Under Test mode to be used with Bluetooth Tester Of course, all the commands are available through a standard UART, connected to a Tester. All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel. 7.4 Mechanical assembly / Industrial feasibility 7.4.1 Board outline The board must be as small as possible. Nevertheless, this depends on the antenna type implemented, and to routing optimizations that could be done. This size may be changed if smaller. Provision is also made for a soldered shield, in case of high interferers. See chapter 7.4.4 for size of the module. 7.4.2 Board technology The board is based on the development kit from Texas instrument.The files related to this contain the schematics, the layout, and the BOM. We will change the TI reference design PCB thickness from 1.7mm to 0.8mm. Nevertherless the thickness of the prepreg layers will stay the same, so the layout can be unchanged. This was checked with Elec&Eltek PCB vendor . Their answer is: “We are ok with the customer original stackup. We also recommend a 1.0mm thickness stackup as per your requiement. Materials will be PIC FL170 instead of IT180. Please note that the gold plating is mandatory, we need to know the gold plating area (with location) for our cost and process capability evaluation. Yes, we propose to use 16mil of the core to meet total thickness 0.8mm.” The proposed stackup for 0.8mm thickness is: Type Thickness L1: Cupper 0.5oz + ENIG plating 2116 pp 4.4 mil L2: Cupper 1oz core 16 mil L3: Cupper 1oz 2116 pp 4.4 mil L4: Cupper 0.5oz + ENIG plating Finished board thickness 0.8+/-0.1mm The PCB is a 4 Layers FR4 controlled impedance with 50 Ohms tracks for the 2.45 GHz radio signals between layers L1 and P2. All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel. 7.4.3 Connections To reduce cost, we want to avoid a board to board connector. The daughter board will use the technique of the cut metal holes on the board edge (top view): Metal holes Gold plating PCB Before milling During milling Resulting connections The connections number is 27, spread over three sides of the board as following: 7.4.4 Mounting on the main board The daughter board is mounted flat directly on the CPU board. This means that: • There is no component on the bottom side of the BTDB All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel. • Also signal vias shall be prohibited to avoid risks of short-circuit with main board GND. There is no component on top of the CPU CPU The solder is put here Daughter board Care must be taken in order to equilibrate the layout, to avoid that the PCB becomes curved during soldering process (due to differential thermal expansion of the copper layers). The cut-hole size must be defined big enough in order to get a solid solder area, and to avoid that the copper of the hole is snatched during milling process. All rights reserved. Passing on and copying of this document, use and communication of its contents not permitted without written authorization from Alcatel. On Main board, the recommended footprint is as follows: The GND pins must be connected to the GND plane as short as possible, with enough vias. Dotted line is the board outline. 7.4.5 Shielding Mounting The target is to deliver a BTDB without shielding. All modules on the market have a shielding. It is required when the chip and sensitive RF parts are exposed to strong perturbations (WIFI, Cellular,..). It is not yet clear if our products using the BTHS will be exposed to such conditions. Also for full Bluetooth and RF certification of this board, the shield may be required. Therefore we have foreseen provision to equip a one-piece surface mount shield. It is preferred to a two pieces part for manufacturing reasons. The following reference shall be used: END OF DOCUMENT
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No Page Count : 26 Producer : GPL Ghostscript 9.04 Create Date : 2017:04:19 09:33:04+08:00 Modify Date : 2017:04:19 09:33:04+08:00 Title : BTDB user's manual Creator : FreePDF 4.06 - http://shbox.de Author : zhangelliotEXIF Metadata provided by EXIF.tools