AMX ACVREM100 Remote Control User Manual ACV 2100 QSG REV A10

AMX LLC Remote Control ACV 2100 QSG REV A10

UserManual.wiki >

ACVREM100 User Manual >

User Manual ACV-2100.QSG

Contents

User Manual ACV-2100.QSG

QUICK START GUIDEACV-2100 Acendo Vibe™ Conferencing Sound BarOverviewThe ACV-2100 features a connector bay door that also serves as a hinged Wall MountBracket, which allows easy access to the Connector Bay without having to dismountthe unit. The Wall Mount Bracket features a cutout for cable routing and straps for cablemanagement. Credenza InstallationNote: To ensure highest possible sound quality, the rubber feet on the bottom panel must remain in place for surface-mount installations.The ACV-2100 can sit on a hard, flat surface such as a credenza, tabletop or desk.When choosing a surface location, consider a space that will not interfere withworkspaces or other installed devices. Connect cables as necessary - see theConnections section for details.Wall Mount InstallationFor best aesthetic in wall mount installations, remove the rubber feet from the bottompanel: carefully peel each foot off of the bottom surface.Removing the Wall Mount Bracket1. Open the Wall Mount Bracket (held closed by internal magnets). 2. Press and hold the Release Button to slide the Wall Mount Bracket out (over the button) to disengage the pins on the bracket from the hinges on the unit (FIG. 2).3. Lift the Wall Mount Bracket off of the hinges to remove (FIG. 3): Mounting the Wall Mount Bracket and Attaching the ACV-21001. Use the Wall Mount Bracket as a template to mark the locations for the (4) mounting screws (not included). Use mounting screws and hardware appropriate for the surface being utilized to secure the bracket to the wall.Optionally, place the four included Wall Mount Spacers between the Bracket/Door and the wall to create a 5mm gap for routing flat cables if not hiding them behind the drywall (see FIG. 6).2. Attach the ACV-2100 to the Bracket/Door by sliding the pins on the bracket into the hinges on the rear of the main unit (see FIG. 3):a. Position the ACV-2100 with the bottom panel facing the wall and align the hinges on the main unit with the pins on the bracket.b. Carefully slide the pins into the hinges, until the bracket/door snaps into place.Note: Press the door into place so that the last pin depresses the Release Button, allowing the pins to slide into the hinges (see FIG. 3).c. With the ACV-2100 attached to the bracket/door, rotate the unit up to its seated position. Note that the door snaps shut and is held closed via internal magnets.Note: Ensure that cables do not obstruct the complete closing of the unit. 3. Connect cables as necessary - open the Wall Mount Bracket to access the connector bay (see FIG. 2).4. Rotate the ACV-2100 into seated position. The Wall Mount Bracket is secured with magnets (see FIG. 6).ConnectionsAll cable connectors are located within the Connector Bay (rear panel). • For surface installations, place the unit face-down and open the Connector BayDoor to manage cables/connectors. • For wall-mounted installations, simply rotate the ACV-2100 unit down and awayfrom the wall to access the Connector Bay.There are two sets of connectors on the inner side panels of the Connector Bay. Eachconnector is labeled on the elastic cable straps (FIG. 5): . Run each cable through the cable access hole in the bracket/door and under thecable strap. FIG. 1 ACV-2100 (FRONT/REAR VIEWS)PRODUCT SPECIFICATIONSMODELS AVAILABLE • ACV-2100GR, Grey (FG4121-00GR)• ACV-2100BL, Black (FG4121-00BL)DIMENSIONS (HWD) • 3" x 23 1/2" x 3 15/16" (76 mm x 590 mm x 100 mm)• Depth with optional wall mount spacers: 4 1/8” (105 mm)WEIGHT 6.3 lbs (2.86 kg)ACTIVE POWER REQUIREMENTS • ~100-240V, 1.3A max• Only use the included power supplyREGULATORY COMPLIANCE FCC 47 CFR Part 15, Subpart C / Subpart B (emissions)EN 55024, EN 60950-1, IEC/EN/UL 60065:2014ENVIRONMENTAL • Temperature (Operating): 32° F to 122° F (0° C to 50° C)• Temperature (Storage): -4° F to 158° F (-20° C to 70° C)• Humidity (Operating): 5% to 85% RH non-condensingINCLUDED ACCESSORIES • 15V / 4A.Power Supply• Remote Control• 6’ USB 2.0 Cable• 5mm Wall Mount Spacers (4)•Lock-Down Screws (2)OPTIONAL ACCESSORIES• CBL-USB-FL2-16, USB 2.0 16ft Extension Cable (FG10-2220-16)• CBL-USB-FL2-33, USB 2.0 33ft Extension Cable (FG10-2220-33)• ACR-5100, Meeting Collaboration System (FG4051-00)FIG. 2 ACV-2100 BOTTOM VIEW - OPENING THE WALL MOUNT BRACKETFIG. 3 ACV-2100 BOTTOM VIEW - REMOVING THE WALL MOUNT BRACKETFrontRear mounting holes (x4)Wall Mount BracketRubber feet (removable, x2)Side PanelKeypadCable CutoutBracket/DoorHinges/PinsRelease ButtonConnector BayBracket/DoorPins (x4)Hinges (x4)Slide pins in to install Slide pins out to removeRelease ButtonFIG. 4 WALL MOUNTING THE ACV-2100FIG. 5 ACV-2100 CONNECTOR BAYMount the Bracket to thewall via 4 mounting screwsAttach the ACV-2100 to theBracket via hinges & pins bamounting screws(x4, not included)mounting spacers(x4, optional)Analog audio input Analog audio output Optical audio inputDC Power inputUSB (Type B) cable strap cable strapRS-232 (3-pin captive wire)

Navigation menu