AMX ACVREM100 Remote Control User Manual ACV 5100 QSG REV A

AMX LLC Remote Control ACV 5100 QSG REV A

UserManual.wiki >

ACVREM100 User Manual >

User Manual ACV-5100.QSG

Contents

User Manual ACV-5100.QSG

QUICK START GUIDEACV-5100 Acendo Vibe™ Conferencing Sound Bar with CameraOverviewThe ACV-5100 features a hinged Wall Mount Bracket, which allows easy installation aswell as access to the Connector Bay without having to dismount the unit. The WallMount Bracket features a cutout for cable routing and straps for cable management. Note: Do not lift the ACV-5100 by the camera.Credenza InstallationNote: To ensure highest possible sound quality, the rubber feet on the bottom panel must remain in place for surface-mount installations.The ACV-5100 can sit on a hard, flat surface such as a credenza, tabletop or desk.When choosing a surface location, consider a space that will not interfere withworkspaces or other installed devices. Connect cables as necessary - see theConnections section for details.Wall Mount InstallationFor best aesthetic in wall mount installations, remove the rubber feet from the bottompanel: carefully peel each foot off of the bottom surface.Removing the Wall Mount Bracket1. Open the Wall Mount Bracket (held closed by internal magnets).2. Press and hold the Release Button to slide the Bracket out (over the button) to disengage the pins on the Bracket from the hinges on the unit (FIG. 2).3. Lift the Wall Mount Bracket off of the hinges to remove (FIG. 3): Wall Mount Considerations•Distance between conference table and display: The closer the table is to thewall-mounted display. the lower the display should be mounted. As a generalguide, the display should be mounted between 40” and 48” from the floor.•Avoid obstructing the camera view: The lens of the camera must be positionedbeyond the bottom surface of the display in order to avoid partially blocking thecamera view.•Position camera for full visibility: In small rooms, it may be necessary to manuallytilt the camera up to maximize visibility for all participants. Using the Bracket Mounting GuideThe Wall Mount Bracket features instructions etched on the inner surface that describehow to position the ACV-5100 beneath a wall-mounted display to avoid obstructing the1. Remove the Bracket from the ACV-5100 (see FIG.7on page 9).2. Turn the Bracket vertically and place against the wall, centered directly beneath the wall-mounted display.3. Align the top of the bracket (see Bottom of Display) with the bottom surface of the display.4. Use the top edge of the notch in the Bracket (see Top flat surface of Acendo Vibe to determine the closest placement for the ACV-5100 beneath the display. Mark the mounting surface.5. Align the top flat surface of the ACV-5100 with the mark made in step 4.6. Mount the Bracket using mounting screws and optional mounting spacers (see FIG. 6).Mounting the Wall Mount Bracket and Attaching the ACV-51001. Use the Wall Mount Bracket as a template to mark the locations for the four mounting screws (not included). Use mounting screws and hardware appropriate for the surface being utilized to secure the Bracket to the wall.Optionally, place the four included Wall Mount Spacers between the Bracket and the wall to create a 5mm gap for routing flat cables if not hiding them behind the drywall (see FIG. 7). 2. Attach the ACV-5100 to the Bracket by sliding the pins on the Bracket into the hinges on the rear of the main unit (see FIG. 3):a. Position the ACV-5100 with the bottom panel facing the wall and align the hinges on the main unit with the pins on the Bracket.b. Carefully slide the pins into the hinges, until the Bracket snaps into place.Note: Press the Bracket into place so that the last pin depresses the Release Button, allowing the pins to slide into the hinges (see FIG. 3)c. With the ACV-5100 attached to the Bracket, rotate the unit up to its seated position. Note that the Bracket snaps shut and is held closed via internal magnets.Note: Ensure that cables do not obstruct the complete closing of the unit. FIG. 1 ACV-5100 (FRONT/REAR VIEWS)PRODUCT SPECIFICATIONSMODELS AVAILABLE • ACV-5100GR, Grey (FG4151-00GR)• ACV-5100BL, Black (FG4151-00BL)DIMENSIONS (HWD) • 5" x 23 1/2" x 3 15/16" (76 mm x 590 mm x 100 mm)• Depth with optional wall mount spacers: 4 1/8” (105 mm))gk 39.2( sbl 54.6THGIEWACTIVE POWER REQUIREMENTS • ~100-240V, 1.3A max• Only use the included power supplyREGULATORY COMPLIANCE FCC 47 CFR Part 15, Subpart C / Subpart B (emissions)EN 55024, EN 60950-1, IEC/EN/UL 60065:2014ENVIRONMENTAL • Temperature (Operating): 32° F to 122° F (0° C to C)• Temperature (Storage): -4° F to 158° F (-20° C to 70° C)• Humidity (Operating): 5% to 85% RH non-condensingINCLUDED ACCESSORIES • 15V / 4A.Power Supply• Remote Control• 6’ USB 2.0 Cable• 5mm Wall Mount Spacers (4)• Lock-Down Screws (2)OPTIONAL ACCESSORIES• CBL-USB-FL2-16, USB 2.0 16ft Extension Cable (FG10-2220-16)• CBL-USB-FL2-33, USB 2.0 33ft Extension Cable (FG10-2220-33)• ACR-5100, Meeting Collaboration System (FG4051-00)FIG. 2 ACV-5100 BOTTOM VIEW - OPENING THE WALL MOUNT BRACKETCameraFrontRearRubber feet (removable, x2) mounting holes (x4)Wall Mount BracketSide PanelKeypadCable CutoutWall Mount BracketHinges/PinsRelease ButtonConnector BayFIG. 3 ACV-5100 BOTTOM VIEW - REMOVING THE BRACKETFIG. 4 ACV-5100 WALL MOUNT CONSIDERATIONSFIG. 5 USING THE MOUNTING GUIDEFIG. 6 WALL MOUNTING THE ACV-5100Wall Mount BracketPins (x4)Hinges (x4)Slide pins in to install Slide pins out to removeRelease ButtonDisplay40-48” from floorCamera lens should bepositioned beyond the displayto avoid obstructing the viewDisplayACV-5100 CameraDisplayfront(side view)Mounting Bracket Mounting Guide(etched into surface)(top view)ACV-5100DisplayMount the Bracket to thewall via 4 mounting screwsAttach the ACV-5100 to theBracket via hinges & pins bamounting screws(x4, not included)mounting spacers (x4, optional)45°

Navigation menu