ARGtek Communication WIFI-015 CPE 2630 User Manual CPE 2630 QIG final 252 251

Download:
Mirror Download [FCC.gov]
Document ID	1616584
Application ID	YGZHMJIF+hlmDjSCtLiyYg==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	12.45kB (155609 bits)
Date Submitted	2012-01-09 00:00:00
Date Available	2012-01-09 00:00:00
Creation Date	2011-01-04 13:25:36
Producing Software	GPL Ghostscript 8.15
Document Lastmod	2012-01-05 14:44:59
Document Title	(Microsoft Word - CPE 2630 QIG_final\252\251_.doc)
Document Creator	PScript5.dll Version 5.2.2
Document Author:	AJXP

CPE2630
Quick Installation Guide
1. Check the parts in your box
CPE SET
DC 12V @ 1.25A Power Adapter
PoE DC Power Injector
Hose Clamps
CD user manual
2. How to fix the CPE on the Pole (1”- 1.5”)
(For better water resistance please wrap the RJ45 connector)
3. PoE connection
1. Connect (POE) RJ45 Jack to CPE RJ45 Jack with good quality
Ethernet cable.
2. Connect (LAN) Jack to PC or Switch Hub LAN port.
3. Plug in the power adaptor to PoE DC jack.
4. CPE Connection
1. Open the CPE enclosure you will find one RJ45 Jacks two LEDs and
one reset button.
2. Connect the PoE cable to either LAN port.
3. To reset the CPE just press and hold the reset button for about 10
seconds and wait for 35 seconds to reboot the CPE.
Notice:
This CPE default operation mode is in Bridge mode. Please go to the
webpage and change the operation mode to other mode for your CPE.
5. CPE configuration
The WLAN Broadband Router is delivered with the following factory
default parameters on the Ethernet LAN interfaces.
Default IP Address: 10.10.10.254
Default IP subnet mask: 255.255.255.0
WEB login User Name: admin
WEB login Password: admin
The device has four operation modes (Gateway/Bridge/WISP/AP Client).
Bridge/WISP/AP Client:
The default IP addresses for the device are 10.10.10.254, so you need to
make sure the IP address of your PC is in the same subnet as the device,
such as 10.10.10.X.
It will take about 25 seconds to complete the boot up sequence after
power on from PoE.
Gateway:
The default IP addresses for the device are 172.32.1.254, so you need to
make sure the IP address of your PC is in the same subnet as the device,
such as 172.32.1.X.
It will take about 25 seconds to complete the boot up sequence after
power on from PoE.
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate this
equipment.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance 50cm between the radiator & your body.
Note: The country code selection is for non-US model only and is not
available to all US model. Per FCC regulation, all WiFi product marketed in
US must fixed to US operation channels only.
Professional installation instruction
Please be advised that due to the unique function supplied by this product, the
device is intended for use with our interactive entertainment software and
licensed third-party only. The product will be distributed through controlled
distribution channel and installed by trained professional and will not be sold
directly to the general public through retail store.
1. Installation personal
This product is designed for specific application and needs to be
installed by a qualified personal who has RF and related rule knowledge.
The general user shall not attempt to install or change the setting.
2. Installation location
The product shall be installed at a location where the radiating antenna
can be kept 50cm from nearby person in normal operation condition to
meet regulatory RF exposure requirement.
3. External antenna
Use only the antennas which have been approved by the applicant. The
non-approved antenna(s) may produce unwanted spurious or excessive
RF transmitting power which may lead to the violation of FCC limit and
is prohibited.
4. Installation procedure
Please refer to user’s manual for the detail.
5. Warning
Please carefully select the installation position and make sure that the
final output power does not exceed the limit set force in relevant rules.
The violation of the rule could lead to serious federal penalty.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Extract
XMP Toolkit                     : 3.1-701
Create Date                     : 2011:01:04 13:25:36Z
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2012:01:05 14:44:59+08:00
Metadata Date                   : 2012:01:05 14:44:59+08:00
Format                          : application/pdf
Creator                         : AJXP
Title                           : (Microsoft Word - CPE 2630 QIG_final\252\251_.doc)
Producer                        : GPL Ghostscript 8.15
Document ID                     : uuid:3345dcd5-c343-4e34-b22d-49aed4f028b9
Instance ID                     : uuid:e6ad92dc-3bdc-4f36-b9c8-c0c7f3f10f7f
Has XFA                         : No
Page Count                      : 7
Author                          : AJXP

EXIF Metadata provided by EXIF.tools