ARRIS WRMTM5 WIRELESS ROUTER MODULE User Manual users manual

ARRIS Group, Inc. WIRELESS ROUTER MODULE users manual

users manual

5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 FCC Part 15.247 Transmitter Certification Direct Sequence Spread Spectrum Transmitter Test Report FCC ID: UID-WRMTM5 FCC Rule Part: 15.247 ACS Report Number: 06-0200-15C Manufacturer: Sercomm Applicant: ARRIS International, Inc. Model: TM552 WRM Installation Guide
站別／站數 作業人數 安全防護 文件版本 發行日期 擬案 機構會簽 製造組長會簽 核准Station NO. Person Safety Protection Doc. Rev. Issue Date Prepared Approved2 Approved2 Approved12/12 1 wear ESD gloves and wrist strap,button slevees REV02 2006/9/6 Laurie Wang 數量QT22TM552 WRM INSTALLATION GUIDE WORKING INSTRUCTION 組裝段 作業名稱 : 鎖主板 主件料號:80-BETNGN-00P機種別/版本 文件編號MODEL NAME/REV. Doc. NO.TM552 WRM M3-701-C06VPA023料號Part NO. 品名Description耗材(品名/料號/規格)Consumers 治工具(品名/料號/規格)Fixture &Tools13GMAPXD050W screw Assembly fixture 13GB4710M510-1 metal stand off Hex driver (Torque:2.8, 0.2kg.f*cm, #5 driver head)1.Confirm 5M checklist before assembly: 5M(manpower,machine,material,method,measurement), any abnormal, please inform the line leader.2.Take two screws and check if any damages on the them. If not, put the two screws onto the fixture with screw head down. (Photo 1)3.Put the motherboard on the fixture. Let two screws on the fixture already go through the through holes of the motherboard. (Photo 2) Photo 1Put the 2 screws with screw head down on the fixturePhoto 24.Take two metal stand offs and make sure there is no damage on them. If so, put the metal stand offs onto the two screws and use hex driver to fasten them. (Photo 3)5. Confirm 5S checklist after operate,any abnormal inform line leader.photo 3
站別／站數 作業人數 安全防護 文件版本 發行日期 擬案 機構會簽 製造組長會簽 核准Station NO. Person Safety Protection Doc. Rev. Issue Date Prepared Approved2 Approved2 Approved13/12 1wear ESD gloves and wrist strap,button slevees REV02 2006/9/6 Laurie Wang 數量QT1工作指導書 WORKING INSTRUCTION 組裝段 作業名稱 : 組裝网卡&主板 主件料號:80-BETNGN-00P機種別/版本 文件編號MODEL NAME/REV. Doc. NO.TM552 WRM M3-701-C06VPA023料號Part NO. 品名Description耗材(品名/料號/規格)Consumers 治工具(品名/料號/規格)Fixture &Tools13GB4710P560-1 plastic stand off1.Confirm 5M checklist before assembly: 5M (manpower, machine, material, method, measurement), if any abnormal, please inform the line leader.2. Take WRM and check whether any missing or scratch on the WRM to make sure the pins of LAN JACK, antenna connecter & reset button are good. Also make sure that solder side is not scrathced or the WRM FW and S/N label is legible, if anything defect, just put it into defect box.3.Take 1 plastic stand off and inspect it to make sure no bending and no scratched. And then, fasten the small foot of the plastic stand off to the bottom side of WRM (Photo 1) 4.Get the WRM and carefully aim at the 2x 12 pin holes to the pin header (location on P601) on the mother board and then plug the pins into the holes.7. Check whether the plastic stand was opposite after inserting.Check method: (1)VI the size of plastic stand's two ends (2)Whether end is loose when plastic stand off is pluged to WRM and to mother board, it shows it's plugged upside down.Plug the plastic stand off inPhoto 4Photo 3Small foot2 x 12 Pin header (P601)2x 12 pin holes on WRMPhoto 25. Click the other end of plastic stand off to the through hole near RJ-11 on the mother board (photo 3).6. Align the PTH of the WRM with the two metal stand offs.(Photo 4)Photo 1
站別／站數 作業人數 安全防護 文件版本 發行日期 擬案 機構會簽 製造組長會簽 核准Station NO. Person Safety Protection Doc. Rev. Issue Date Prepared Approved2 Approved2 Approved14/12 1wear ESD gloves and wrist strap,button slevees REV02 2006/9/6 Laurie Wang 數量QT21工作指導書 WORKING INSTRUCTION 組裝段 作業名稱 : 鎖网卡&主板 主件料號:80-BETNGN-00P機種別/版本 文件編號MODEL NAME/REV. Doc. NO.TM552 WRM M3-701-C06VPA023料號Part NO. 品名Description耗材(品名/料號/規格)Consumers 治工具(品名/料號/規格)Fixture &Tools13GMAPXD050W screw assembly fixture04G030002100 WRM electric screw driver (torque:2.8 0.2kg.f*cm,#1 screw driver head)1.Confirm 5M checklist before assembly: 5M (manpower, machine, material, method, measurement), if any abnormal, please inform the line leader. 2.Take the assembled WRM and mother board from the production line,check whether the plastic stand off is clipped good, the 2x12 pins are plugged good (all the pins need to go through the holes.) (Photo 1)3.Get two screws and put them to the PTH of the WRM. Use electric screw driver to fasten the screws. (Photo 2)4.Modify the torgue value of electric screw driver before operating.5.Put the locked board on the production line.6.Confirm 5S checklist after operate,any abnormal inform line leader.圖二Photo 1 Photo 2fasten screws on
NOTICE TO USERFCC Class B: “NOTE: This equipment has been tested and found to comply withthe limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interferencewill not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver.Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.” Warning: Changes or modifications to this device not expressly approved by ARRIS International, Inc. could void the user’s authority to operate the equipment. RF Exposure In accordance with FCC requirements of human exposure to radiofrequency fields, the radiating element shall be installed such that a minimum separation distance of 20cm shall be maintained from the user and/or general populationIC: This Class Bdigital apparatus meets all requirements of theCanadian Interference Causing Equipment Regulations. Operationis subject to the following two conditions: (1) this device may notcause harmful interference, and (2) this device must accept anyinterference received, including interference that may causeundesired operation.Cet appareillage numérique de la classe Brépond à toutes lesexigences de l'interférence canadienne causant des règlementsd'équipement. L'opération est sujette aux deux conditionssuivantes: (1) ce dispositif peut ne pas causer l'interférencenocive, et (2) ce dispositif doit accepter n'importe quelleinterférence reçue, y compris l'interférence qui peut causerl'opération peu désirée. NOTES:1This device has been designed to operate with the antennas listedbelow, and having a maximum gain of 1.8dBi. Antennas not included in this list or having a gain greater than 1.8dBi are strictly prohibited for use with this device. The required antenna impedance is 50 ohms.2To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (EIRP) is not more than that required for successful communication. The approved antennas used with this device are 1. C147-510023-A and 2. C66-510003-A.

Navigation menu