ASSALOY SCYICLS2 Microprocessor Controlled Networked Locks User Manual XX XXXX Exhibit Cover
ASSA ABLOY Inc. Microprocessor Controlled Networked Locks XX XXXX Exhibit Cover
ASSALOY >
Contents
- 1. P1 Manual
- 2. P2 Manual
- 3. TCP Manual
P2 Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1450096 |
| Application ID | ul8b2CIRx1Qo6IELHp2Ecw== |
| Document Description | P2 Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 175.58kB (2194721 bits) |
| Date Submitted | 2011-04-18 00:00:00 |
| Date Available | 2011-04-19 00:00:00 |
| Creation Date | 2011-04-13 14:36:14 |
| Producing Software | Adobe Acrobat 9.0.0 |
| Document Lastmod | 2011-04-13 14:36:14 |
| Document Title | Microsoft Word - XX-XXXX - Exhibit Cover.doc |
| Document Creator | Adobe Acrobat 9.0.0 |
| Document Author: | beth.gray |
Certification Exhibit FCC ID: U4A-SCYICLS2 IC: 6982A-SCYICLS2 FCC Rule Part: 15.225 IC Radio Standards Specification: RSS-210 ACS Report Number: 11-0071.W06.11.A Manufacturer: Assa Abloy, Inc. Model: P2-IM/IKM Manual 5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 IN AR P2 IM PASSPORT 1000 EL Mortise Lock PR Installation Instructions A8011E 12/10 Copyright 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited. Table of Contents Warning . ..................................................................................2 General Description..................................................................3 Hardware Specifications..........................................................3 Electronic Specifications..........................................................3 Parts Breakdown......................................................................4 Installation Instructions...........................................................7 Operational Check .................................................................14 AR Warning Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. IN FCC 10/10/10 IM EL This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. PR Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. Industry Canada: Statement: The term “IC:” before the radio certification number only signifies that Industry Canada technical specifications were met. This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Cet appareillage numérique de la classe B répond à toutes les exigences de l’interférence canadienne causant des règlements d’équipement. L’opération est sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas causer l’interférence nocive, et (2) ce dispositif doit accepter n’importe quelle interférence reçue, y compris l’interférence qui peut causer l’opération peu désirée. To comply with “Fire Listed” doors, the batteries must be replaced with alkaline batteries only. 1-800-810-WIRE • www.sargentlock.com • A8078A Passport 1000 Series P2 Mortise Lock General Description The SARGENT Passport Series v.P2 Mortise Lock is available with either an HID® Prox 125 kHz or 13.56 MHz iCLASS® technology reader. Designed specifically for the campus market, the SARGENT Passport 1000 P2 WiFi Mortise Lock is a new breed of electronic lock, providing access control with magnetic swipe and optional Proximity Reader and/or Keypad, as well as detailed audit capabilities. • Using WiFi technology and coupled with third party software, the P2 Mortise lock offers a complete, integrated access control system. • The Passport 1000 P2 operates on six (6) “AA” alkaline batteries and may be used for both indoor and outdoor applications. Note: A weather-protective gasket is recommended for outdoor applications. Hardware Specifications • Case - 12 gauge heavy duty wrought steel • Complete lockset with on-board memory • Magnetic swipe standard with optional 125 kHz • Proximity Reader (specify PRX-), 13.56 MHz reader (specify IKM-), and/or keypad (specify • KP-) • ADA compliant Outside lever is unlocked through access control credentials only • Easily retrofits existing Passport 1000 door preps (mortise) • Lock furnished for 1-3/4” doors. For other thicknesses, Consult factory. • Latch - Stainless steel • UL Listed (3 hr.) • Optional deadbolt - Stainless steel • Guardbolt - Stainless steel, non handed • Handing (RH/RHR/LH/LHR) must be specified, • Outside lever for iCLASS controlled by HID iCLASS but is easily field-reversible without opening credential or other 13.56 MHz credential (such as CSN, Chip the lock case IN • Wireless (WiFi 802.11 b/g) online, batteryoperated • 2,400 users per lock; 10,000 event audit trail • Multiple time zone and holiday access scheduling • First-In unlock configuration, either by time or by user (selectable) • Input Power: DC 9V, 1.5A (6 AA alkaline batteries or optional hard-powered) Serial Number, read only supported, including MiFare, DesFire, and Felica) • Uses existing Magstripe keycards (track 2) • Magnetic Stripe Card Coercivity: HiCo (4000 Oersted) or LoCo (300 Oersted) • Supports HID 125 kHz prox or 13.56 MHz iCLASS credentials (26 - 39 bit); supports CSN reads for other common 13.56 MHz cards, including MiFare, DesFire, and FeliCa • AWE Prefix Available for WPA2, PEAP and EAPTLS Wireless Encryption Support 1-800-810-WIRE • www.sargentlock.com • A8011E Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. IM EL Electronic Specifications Inside lever retracts latch and deadbolt simultan ously • Outside lever controlled by any combination of keypad, magnetic swipe, iCLASS, prox (proximity) reader, or mechanical cylinder PR • Cylinder retracts latchbolt (and deadbolt) 12/15/10 AR HID and iCLASS are registered trademarks of HID Global Corporation. Passport 1000 Series P2 Mortise Lock Parts Breakdown P2 WiFi Lock with Magnetic Card Swipe With or Without Keypad 10 10 14 13 13 13 12 12 12 11 11 11 10 10 10 10 10 99 AR Inside IN IM Inside Inside Outside Outside PART No. DESCRIPTION 52-0757 Lens (Cliplite) 52-0738 Outside Passport Escutcheon Only (Magnetic Swipe and Keypad) PR ITEM No. EL Outside Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. 12/15/10 P2 P2 52-0739 Outside Passport Escutcheon Only (Magnetic Swipe) 52-0760 Light Pipe (Cliplite) 52-3594 Slim Style Keypad Assembly 01-9299 #4-40 x 3/16” Phillips Pan Head Screw 52-4243 Swipe Reader Assembly 52-0745 Online Interface PCB 52-3209 Harness Assembly 52-0748 Inside Mounting Plate 10 77-0168 #8-32 x 1-7/8” Phillips Flat Head Screw 11 01-1146 #8-32 x 3/8” Phillips Flat Head Screw 01-1176 #8 x 3/8” Phillips Flat Head Wood Screw 12 52-4246 Modular Component 13 52-3592 Inside Escutcheon Assembly 14 01-4421 #8-32 x 1/2” T-20 Torx Pan Head Screw 1-800-810-WIRE • www.sargentlock.com • A8011E Passport 1000 Series P2 Mortise Lock Parts Breakdown (Continued) P2 WiFi Lock with Magnetic Card Swipe, 125 kHz and Keypad 11 13 AR 12 10 Inside Inside Outside IM IN P2 PART No. DESCRIPTION 52-1103 Outside Passport Escutcheon only (Magnetic Swipe, Keypad and Proximity Reader) 52-3593 Slim Style Keypad Assembly 01-9299 #4-40 x 3/16” Phillips Pan Head Screw 52-4243 Swipe Reader Assembly 52-1106 Prox Reader Gasket 52-4206 Antenna Assembly 52-0745 Online Interface PCB 52-3209 Harness Assembly 52-1109 Back Plate 10 52-0748 Inside Mounting Plate 11 77-0168 #8-32 x 1-7/8” Phillips Flat Head Screw 12 01-1146 #8-32 x 3/8” Phillips Flat Head Screw 01-1176 #8 x 3/8” Phillips Flat Head Wood Screw 13 52-0751 Battery Cartridge (Only) 14 52-4263 AWE Controller Assembly Kit 52-4247 Modular Component and Battery Cartridge Kit 15 52-3592 Inside Escutcheon Assembly 16 01-4421 #8-32 x 1/2” T-20 Torx Pan Head Screw 1-800-810-WIRE • www.sargentlock.com • A8011E 12/15/10 ITEM No. Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. Outside EL PR 10 10 16 10 11 12 14 13 15 Passport 1000 Series P2 Mortise Lock Parts Breakdown (Continued) P2 WiFi Lock with Magnetic Card Swipe, 13.56 MHz and Keypad AR IN IM 12/15/10 PR EL Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. 10 ITEM No. PART No. DESCRIPTION 52-4402 Outside Mask Assembly 52-1255 Outside Escutcheon - iCLASS 52-3593 Slim Style Keypad Assembly 01-9299 #4-40 x 3/16” Machine Screw 52-4243 Swipe Reader Assembly 52-4401 iCLASS Module Assembly 52-3209 Harness Assembly 52-4410 iCLASS Harness 52-1109 Back Plate 10 01-9300 #4-32 x 5/16” Plastite Screw 1-800-810-WIRE • www.sargentlock.com • A8011E Passport 1000 Series P2 Mortise Lock Parts Breakdown (Continued) 8200 Series Mortise Lock 13 11 12 AR 10 IN 16 17 PART No. See catalog #41 Cylinder (1-1/8” Minimum Length) 13-0140 Cylinder Compression Spring See catalog 1KB-1 Cylinder Rosette See catalog Mortise Lockbody 77-2592 130 KB Thumbturn for Deadbolt Functions Only See catalog Inside Lever Handle See catalog Outside Lever Assembly 82-0368 Spindle 82-3088 Inside Lever/Knob Adapter Plate Assembly 10 01-1495 #8-32 X 5/8 Machine Screw 11 82-0612 Non Loosening Wave Washer 12 See catalog Mortise Rose 13 82-0347 Spindle Spring 14 01-1019 #12-24 X 1/2” Machine Screw 15 01-2299 12 X 1-1/4 Wood Screw 16 82-0578 Outside Front Plate (Electrical, Latchbolt & Guardbolt) 82-0579 Outside Front Plate (Electrical, Deadbolt, Latchbolt and Guardbolt) 01-1028 #8-32 X 1/4 Machine Screw PR 17 DESCRIPTION EL ITEM Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. 15 1-800-810-WIRE • www.sargentlock.com • A8011E 12/15/10 IM 14 Passport 1000 Series P2 Mortise Lock Installation Instructions Door Preparation A. Verify Hand and Bevel of Door B. Verify Product Label Left Hand Reverse Bevel Hinges Left. Open Outward. “LHRB” Right Hand Hinges Right. Open Inward. “RH” AR Left Hand Hinges Left. Open Inward. “LH” Stand on outside of locked door when determining door hand. Right Hand Reverse Bevel Hinges Right. Open Outward. “RHRB” IN • (IKM-) (KP-) P2- (PRX-) 82276 x Rose & Lever x Finish x Hand • (IKM-) (KP-) P2- (PRX-) 82277 x Rose & Lever x Finish x Hand • (IKM-) (KP-) P2- (PRX-) 82278 x Rose & Lever x Finish x Hand IM • (IKM-) (KP-) P2- (PRX-) 82279 x Rose & Lever x Finish x Hand Note: KP- is for the optional Keypad and PRX- is for the optional Proximity Reader 12/15/10 EL Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. C. Door Preparation Refer to template A7950 for wood and metal doors. PR Outside of Door Inside of Door Through Bolt Holes Inside Mounting Plate Mounting Holes Through Bolt Holes Raceway for Power Raceway for Power Controller Cutout Controller Cutout Cylinder Hole Thumb Turn Location (Deadbolt Functions Only) Lever Handle Holes Lever Handle Holes Mortise Pocket (8200) 1-800-810-WIRE • www.sargentlock.com • A8011E Passport 1000 Series P2 Mortise Lock Connector 2 How to Change Hand of Lockbody Ring Terminal A. Reverse Lock Hand Red surface of locking piece must face the outside/ locked side of door. To rotate locking piece (Fig. 2A): 1. Position lock body with red surface of locking piece visible. 2. Insert blade type screwdriver into locking piece slot to rotate locking piece toward back of lock body. 3. Rotate the locking piece 180° until RED surface is on opposite side. Slot AR IM Latchbolt Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. 2. Orient the plastic retaining ring so that the word Bottom is located at the bottom of the cylinder hole. PR EL 3. Route the wires from the top of the cylinder hole into the slot on the top of the plastic retaining ring, NOT through the retaining ring. C. Reverse Latch Hand Beveled surface of latchbolt must face strike. The deadlatch is self adjusting. To change the hand of the latchbolt: 1. Insert the blade of a slotted screwdriver (>1/4”) into the spade shape slot behind latch. Right Hand Lock Shown 2. Rotate the screwdriver 90° to push latchbolt out until back of bolt clears lock case front. 3. Rotate latchbolt 180° until the latchbolt drops back into the lockbody. Note: Latch cannot be unscrewed. Locking Slide Red on locked side Push In Fig. 2A 1-800-810-WIRE • www.sargentlock.com • A8011E 12/15/10 1. The wires and the plastic retaining ring must be located on the non-cylinder side. Inside of Door IN B. Retaining Ring Make sure the plastic retaining ring is seated correctly (Fig. 2B): Plastic Retaining Ring Note: Red indicates locked side (outside). Wire harness MUST exit through the inside/non-cylinder side of the lockbody. Passport 1000 Series P2 Mortise Lock 3 Install Lock Body 1. Feed the wires first through the mortise pocket and out the inside prep, followed by the lockbody (Fig. 3A). 2. The wires from the lockbody exit the inside door prep through the mortise pocket (Fig. 3B). 3. Loosely secure the lockbody in the door with two #12 x 1-1/4” wood screws or #12-24 x 1/2” machine screws. Must feed the harness first, followed by the lockbody. Mortise Lockbody Connector and Grounding Lug AR (2) #12 x 1-1/4” Long Flat Head Wood Screw for Wood Doors IM IN (2) #12-24 x 1/2” Long Flat Head Machine Screw for Metal Doors 12/15/10 Fig. 3B EL Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. Fig. 3A 4 Install Cylinder PR 1. Slide cylinder through the spring and rosette/collar and screw into lockbody, rotating the cylinder clockwise. Cylinder should be flush with rosette/collar. Note: SARGENT logo must be horizontal and on the top of the cylinder (Fig. 4B). 2. Secure the cylinder by tightening cylinder clamp screw located above the deadbolt. 3. Using the key, verify that the key retracts the latchbolt (and deadbolt). Position cylinder so that the SARGENT logo is right-side up. Correct Incorrect Fig. 4B 10 1-800-810-WIRE • www.sargentlock.com • A8011E Align cylinder groove with tapped hole, then tighten set screw to hold lock cylinder. Passport 1000 Series P2 Mortise Lock 5 Install Inside and Outside Levers 1. Slide the outside lever and spindle assembly through the door and lockbody. 2. Using the inside adapter plate and spindle, secure loosely with (2) #8-32 screws. Note: Position threaded hole on the inside adapter to align with lever hole. 3. Tighten the lockbody screws on edge of door. 4. After the lockbody screws are tightened, tighten both inside adapter screws. 5. Position and attach rose over inside adapter. IM Fig. 5A Mortise Lock Body Connector and Ground Ring Terminal Rose Inside Adapter Plate Inside Lever EL 6 Deadbolt Functions Only (82276 & 82277) Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. IN Outside Lever Assembly AR 6. Position and secure inside lever to the inside adapter with set screw. 1. Insert alignment tool (supplied) into lock body thumb turn. PR 2. Slide back plate over tool and make level. 3. Secure back plate to door with two (2) #6 x 3/8” round head wood screws or #6-32 x 3/8” round head machine screws. 4. Dispose of tool, position thumb turn over back plate (Fig. 6A) and secure with #6-32 x 1/4” flat head screw. Back Plate #6 x 3/8” Round Head Wood Screws Note: Thumb turn should cover screw head when deadbolt is retracted. #6-32 x 3/8” Round Head Machine Screws Refer to instructions (A5675G) included in package included with lock. Thumb Turn #6-32 x 1/4” Flat Head Screw Alignment Tool Fig. 6A 1-800-810-WIRE • www.sargentlock.com • A8011E 11 12/15/10 Fig. 6B Detail Passport 1000 Series P2 Mortise Lock 7 Install Gasket (Optinal) Note: Optional, for non-fire rated doors only. For non-fire rated door applications, an optional gasket may be used as a weather seal between the escutcheon and the outside door surface. Gasket Peel off adhesive backing and attach to outside escutcheon. Outside Passport Trim 1. Insert the mounting posts through holes as shown. 2. On the inside of the door, position the mounting plate over the indicated holes. AR 8 Install Outside Escutcheon and Mounting Plate Assembly IN Note: Feed controller and keypad cables feed through side opening (Fig. 8A). Cable and ground ring terminal from lockbody feeds from bottom (Fig. 8A and 8B). IM EL Lock Ground IMPORTANT: If the following step is skipped, the product will not be UL-compliant: PR Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. 12/15/10 Controller/Reader Cable Make sure it is positioned upright (Fig. 8A). 5. Attach two (2) #8 x 3/8” flat head wood screws for wood doors or (2) #8-32 x 3/8” flat head machine screws for metal doors (Fig. 8C). Mounting Plate Reader Cable (iCLASS only) 3. Attach ground ring terminal lock body to bottom right corner using one #8-32 x 1-7/8” flat head machine screw. 4. Insert other three #8-32 x 1-7/8” flat head machine screws and tighten, fastening the outside escutcheon to the door (Fig. 8B). Fig. 7A Position ground ring terminal upright, then tighten screw. Lockbody Cable Fig. 8B Mounting Plate Outside Passport Trim (4) #8 - 32 x 1-7/8” Flat Head Machine Screws (2) #8 - 3/8” Flat Head Wood Screws OR (2) #8 - 3/8” Flat Head Machine Screws Reader Cable (iCLASS only) Reader/Controller Cable Lock Cable Attach ground wire to bottom right screw Fig. 8A 12 1-800-810-WIRE • www.sargentlock.com • A8011E Fig. 8C Passport 1000 Series P2 Mortise Lock 9 Install Inside Module Component Assembly Insert bottom of Module Component Assembly first (Fig. 9A), then clip top of Assembly to backplate, verifying both tabs attached securely. Tabs Outside of Door AR Fig. 9A IN 10 Attach Connectors Secure the following connectors onto the circuit board (Fig. 10A and 10B): IM 1. Secure the 10-pin lock body assembly connector. 2. Secure the 24-pin keypad/card reader connector. Connectors go on only one way. • Do not force and do not offset connectors. • Be sure the connectors are completely seated (flush). PR • Detail 10B 24-pin from Outside Trim 9-pin Reader Cable (iCLASS Only) Fig. 10A 10-pin from Lockbody Fig. 10B Detail 1-800-810-WIRE • www.sargentlock.com • A8011E 13 12/15/10 EL Notes: Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. 3. Secure 9-pin reader cable (iCLASS only). Passport 1000 Series P2 Mortise Lock 11 Install Battery/Battery Pack 1. Place (6) “AA” batteries into the compartment being careful to align polarity (- & +) properly. 2. Insert battery pack and click into place, making sure polarity terminals on the battery pack are correctly oriented (Fig. 11A). 12/15/10 IM EL 12 Attach Outside Front Plate 1. Position inside escutcheon as shown (Fig. 12A). Verify that all wires are positioned within the escutcheon to avoid pinching. PR Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. IN AR Fig. 11A (2) #8-32 x 1/2” Torx Screws 2. Attach escutcheon with (2) #8-32 x 1/2” T-20 Torx pan head screws. 3. Straighten escutcheon and tighten securely. DO NOT OVERTIGHTEN. Fig. 12A 14 1-800-810-WIRE • www.sargentlock.com • A8011E 1-800-810-WIRE • www.sargentlock.com • A8011E 15 12/15/10 Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited. IM EL PR IN AR Passport 1000 Series P2 Mortise Lock 13 Attach Outside Front Plate Attach front plate with (2) #8-32 X 1/4” flat head screws (Fig. 13A). (2) #8-32 x 1/4” Flat Head Screws Fig. 13A 7 Installation Instructions IMPORTANT: Be sure to test functions prior to closing door. In all cases, perform the following checks: 1. Ensure that inside lever retracts latch (and deadbolt for deadbolt functions). • For units with cylinders, the following checks apply: Insert key into cylinder and rotate: b. The key should retract the latch and the key should rotate freely. a. There should be no friction against lock case, wire harness, or any other obstructions. If friction or binding occurs, readjust cylinder and wiring harness to eliminate issues. AR c. The key should extend and retract the deadbolt. For units without a keypad, add card using LCT software and test. • For units with a keypad, add pin and card using LCT software and test. IN • 2. LED signalling: After using a valid credential, a green flash followed by three fast amber flashes indicates a low power condition. IM • Check the battery voltage. • EL If the voltage is low, replace the batteries. If the batteries die, the lock will flash rapid amber for approximately one minute. After that, the lock will no longer be functional. PR 3. When you have completed the tests, close the door, ensuring latchbolt and deadbolt fully extend into strike plate without binding. SARGENT Manufacturing 100 Sargent Drive New Haven, CT 06511 USA 800-810-WIRE (9473) • www.sargentlock.com Founded in the early 1800s, SARGENT® is a market leader in locksets, cylinders, door closers, exit devices, electro-mechanical products and access control systems for new construction, renovation, and replacement applications. The company’s customer base includes commercial construction, institutional, and industrial markets. Copyright © 2010, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited. ASSA ABLOY is the global leader in door opening solutions, dedicated to satisfying end-user needs for security, safety and convenience. A8011E -12/10
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Author : beth.gray Create Date : 2011:04:13 14:36:14-04:00 Modify Date : 2011:04:13 14:36:14-04:00 Has XFA : No XMP Toolkit : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00 Metadata Date : 2011:04:13 14:36:14-04:00 Creator Tool : Adobe Acrobat 9.0.0 Format : application/pdf Title : Microsoft Word - XX-XXXX - Exhibit Cover.doc Creator : beth.gray Document ID : uuid:74d39440-9b3b-4fcb-971f-886beeef96a4 Instance ID : uuid:60f223d2-2530-429a-8de4-1f54febdbc03 Producer : Adobe Acrobat 9.0.0 Page Count : 17EXIF Metadata provided by EXIF.tools