ASUSTeK Computer HD05UGPZ5 BLUETOOTH MODULE User Manual 2 OF 4

Download:
Mirror Download [FCC.gov]
Document ID	546596
Application ID	DvyuuR1KcETx2k67/LiPlg==
Document Description	USER MANUAL 2 OF 4
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	282.27kB (3528375 bits)
Date Submitted	2005-05-30 00:00:00
Date Available	2005-05-27 00:00:00
Creation Date	2004-11-30 09:24:19
Producing Software	Acrobat Distiller 5.0 (Windows)
Document Lastmod	2005-05-26 16:18:42
Document Title	USER MANUAL 2 OF 4

Introduction
第 77 頁，共 224 頁
Using a mobile telephone for fax transmissions
[FAX]
This section describes how to send a fax using a mobile telephone as a modem.
→Setting up the mobile telephone
→Installing a modem
→Setting fax information
→Sending a fax
→Receiving a fax
Important
Please ensure that any drivers used to connect the PC to the mobile telephone have been
installed.
A Bluetooth passkey (PIN code) is required for you to connect to the mobile telephone.
Please make a note of your Bluetooth passkey before you start the set -up process.
A fax application is required for you to be able to send and receive faxes. The description
below is based on a example using Microsoft Fax, which is installed with Windows XP as
standard.
If you are going to use a commercially available fax application , then please refer to the
manual that came with the application for information on how to send and receive faxes.
Setting up the mobile telephone
Set up and register the mobile telephone as a fax service.
Procedure
1. Turn on the mobile telephone, and set it to be connectable via Bluetooth
Note
Please refer to the instruction manual for information on how to operate the
telephone.
2. Right-click on the Bluetooth icon in the task tray, and then click on [Add New
Connection]
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 78 頁，共 224 頁
Note
Alternatively, click [Start] →[All Programs]→[Bluetooth]→[Bluetooth Settings],
and then click on [New Connection] from the active [Bluetooth Settings]
window.
The [Add New Connection Wizard (Welcome to the Add New Connection Wizard)]
window will appear.
3. Select [Custom Mode], and then click on the [Next] button
The [Add New Connection Wizard (Searching for Bluetooth devices)] window will
appear.
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 79 頁，共 224 頁
Once the program has finished searching for the devices, the [Add New Connection
Wizard (Select Device)] window will appear.
4. Select the device name of the mobile telephone from [Device List], and then click on
the [Next] button
The [Add New Connection Wizard (Searching for Services)] window will appear.
5. If you are connecting to the mobile telephone for the first time, enter the passkey for
the device from the [Bluetooth Passkey (PIN Code)] window, and then click on the
[OK] button.
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 80 頁，共 224 頁
Once the program has finished searching for the services, the [Add New Connection
Wizard (Select Service)] window will appear.
6. Select "Fax" under [Select Service], and then click on the [Next] button
The [Add New Connection Wizard (Connecting to Remote Device)] screen will
appear.
The COM port and modem registration process will then be automatically performed.
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 81 頁，共 224 頁
Once the
COM port and modem (standard 33600 bps type) registration is complete,
the [Add New Connection Wizard (Setting Connection Name)] screen will appear.
7. Configure the type and name of the icon to appear after registration, and click on the
[Next] button.
Please click only on the [Next] button once you are satisfied with the configuration.
The [Add New Connection Wizard (Completing the Add New Connection Wizard)]
screen will appear.
8.
Click on the [Finish] button
The settings will be registered, and the icon will appear on the [Bluetooth Settings]
screen.
Setting fax information
Configure send/receive settings and register fax information.
Procedure
1. Select [Start]→[Control Panel], and then double -click on the [Printers and Other
Hardware] icon
Note
If the control panel is displayed in "Classic view", and you use Windows 2000,
please start from Step (2).
2. Double-click on the [Printers and Faxes] icon
The [Printers & Faxes] window will appear.
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 82 頁，共 224 頁
3. Click on "Set up faxing" in the [Printers and Faxes] window
A window showing installed programs will appear, and a Fax icon will have been
created in the [Printers and Faxes] screen.
4. Click on "Send a fax" under "Printer Tasks" on the left side of the window
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 83 頁，共 224 頁
If you have not yet configured a fax device, the [Fax Configuration Wizard] window
will appear. In the window you can enter settings pertaining to the sender (yourself).
Note
If the fax configuration information has already been registered, the [Send Fax
Wizard] window, which can be viewed under " Sending a fax" below, will appear
instead of the [Fax Configuration Wizard] window.
5. Enter the sender information, and click on the [Next] button
Note
The sender information that you configure here will be automatically appended
as header information when you send a fax.
The [Fax Configuration Wizard (Select Device for Sending or Receiving Faxes)]
window will appear.
6. Select a device to be used for fax transmissions, enable the device for sending or
receiving, and then click on the [Next] button
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 84 頁，共 224 頁
Note
If [Enable Receive] is selected, the device will be on standby for receiving faxes
even if it is not sending or receiving anything, and therefore will be in
continuous connection to the wireless modem （when COM Auto Connect is
on).
Please decide whether to select this option based on to the desired objective
and/or frequency of transmission.
The [Fax Configuration Wizard (Transmitting Subscriber Identification (TSID))]
window will appear.
7. Click on the [Next] button
It is important that you do not change the transmitter subscriber identification.
The [Fax Configuration Wizard (Completing the Fax Configuration Wizard)] window
will appear.
8. Click on the [Finish] button
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 85 頁，共 224 頁
The fax information will be have been registered, and the [Fax Console] window will
appear.
This will complete the fax set -up process.
Related topics: " Sending a fax" and "Receiving a fax "
Sending a fax
This section describes how to send a fax from the Fax Console.
Important
The Fax service must be enabled for sending in order for you to send a fax.
Please refer to " Using a mobile telephone " under "Troubleshooting" for how to change
the send and receive settings once the service has been configured.""
Procedure
1. Double-click on the [Fax] icon in the Control Panel
The [Fax Console] window will appear.
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 86 頁，共 224 頁
2. In the [Fax Console] window, click [File] →[Send fax]
The [Send Fax Wizard (Starting the Send Fax Wizard)] window will appear.
3. Click on the [Next] button
The [Send Fax Wizard (Recipient Information)] window will appear.
4. Enter the name and fax number of the destination party, and then click on the [Next]
button
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 87 頁，共 224 頁
The [Send Fax Wizard (Preparing the Cover Page)] window will appear.
5. Specify the cover page template, subject line, and note (body text), and then click on
the [Next] button
The [Send Fax Wizard (Schedule)] window will appear.
6. If you wish to send the fax immediately, select "Now", and then click on the [Next]
button
The [Send Fax Wizard (Completing the Send Fax Wizard)] window will appear.
7. Confirm the destination information and transmission details, and then click on the
[Finish] button
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 88 頁，共 224 頁
The software will automatically dial the number and send the fax.
Once the fax has been sent, Fax Monitor will revert to standby mode.
Related topic: " Receiving a fax "
Receiving a fax
This section describes what to do when a fax arrives after you have established a connection
to a modem station.
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 89 頁，共 224 頁
Important
The Fax service must be enabled for receiving in order for you to receive a fax.
Please refer to " Using a mobile telephone " under "Troubleshooting" for information on
how to change the send and receive settings once the fax service has been configured.
Please ensure you have connected to a modem station before you receive a fax (the
device will be connected to the modem if "Enable Receive" has been selected or COM
Auto Connect has been activated).
Procedure
1. When a fax arrives, the Fax Monitor will start automatically as the fax is received
Once the fax has been received, the Fax Monitor will revert to standby mode.
Note
If you have enabled manual fax reception, the message below will appear when a
fax arrives.
Click on the message with your mouse to receive the fax.
2. Double-click on the [Fax] icon in the Control Panel
The [Fax Console] window will appear.
3. In the [Fax Console] window, double -click on the fax that has arrived
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 90 頁，共 224 頁
An image of the received fax will be displayed.
Related topic: " Sending a fax"
Printing
This section describes how to use a Bluetooth -compatible printer for printing.
Types of printer functions
When printing using Bluetooth, the methods for configuring and using the printer will vary
with the corresponding profile.
Profile
Bluetooth Settings
Operation
SPP
You must register the
printer in Bluetooth
Settings
Allows you to print from various applications, as
with ordinary cable-connected printers.
→"Printing document and images"
OPP (*2)
Not required
BIP
Not required
HCRP (*1)
Allows you to print business card data directly.
→"Printing business card data"
Allows you to print image data directly.
→"Printing images directly from a digital camera
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 91 頁，共 224 頁
or other device"
Note
(*1) The majority of Bluetooth -compatible printers support HCRP.
If you have selected Express Mode, HCRP will be chosen as the default profile. If the
printer does not support HCRP, then SPP will be the next choice.
(*2) The printing of business cards using OPP complies exclusively with the business
card (vCARD) standard.
Printing documents and images
[HCRP] [SPP]
This section describes how to print using a Bluetooth -compatible printer.
→Setting up the printer
→Printing
Important
Please ensure that any printer -specific drivers have been installed on the PC before you
have established a Bluetooth connection.
A Bluetooth passkey (PIN code) is required for you to connect to the printer. Please
make a note of your Bluetooth passkey before you start the set -up process.
Setting up the printer
Procedure
1. Turn on the printer
2. Right-click on the Bluetooth icon in the task tray, and then click on [Add New
Connection]
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 92 頁，共 224 頁
Note
Alternatively, click [Start] →[All Programs]→[Bluetooth]→[Bluetooth
Settings], and then click on [New Connection] from the active [Bluetooth
Settings] window.
The [Add New Connection Wizard (Welcome to the Add New Connection
Wizard)] window will appear.
3. Confirm that [Express Mode] has been selected, and then click on the [Next]
button
The [Add New Connection Wizard (Searching for Bluetooth devices)] window
will appear.
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 93 頁，共 224 頁
Once the program has finished searching for the devices, the [Add New
Connection Wizard (Device Selection)] window will appear.
4. Select the device name of the printer from [Device List], and then click on the
[Next] button
The [Add New Connection Wizard (Searching for Services)] window will appear.
5. If you are connecting to the printer for the first time, enter the passkey for the
device from the [Bluetooth Passkey (PIN Code)] window, and then click on the
[OK] button.
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 94 頁，共 224 頁
Once the services have been detected successfully, connection to the device and
creation of the HCRP port will be performed automatically.
If you have not yet installed a printer, a message prompting you to install a printer
will appear.
6. Click on the [OK] button
The [Add Printer Wizard (Starting the Add Printer Wizard)] window will appear.
7. Click on the [Next] button
The [Add Printer Wizard (Local Printer or Network Printer)] window will appear.
8. Select "Local printer attached to this computer", remove the check next to
"Automatically detect and install my Plug and Play printer", and then click on the
[Next] button
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 95 頁，共 224 頁
The [Add Printer Wizard (Select Printer Port)] window will appear.
9. Select the desired port, and then click on the [Next] button
The [Add Printer Wizard (Install Printer Software)] window will appear.
10. Select the [Manufacturer] and [Printer] as pertains to the printer to be installed, or
click on the [Use Device] button, and then click on the [Next] button
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 96 頁，共 224 頁
Please install the printer according to the instructions in the windows that follow.
Once installation is complete, a message of confirmation will appear in the [Add
New Connection Wizard (Printer Settings)] window.
11. Click on [Next]
The [Add New Connection Wizard (Connection Name Settings)] window will
appear.
12. Enter the type and name of the icon displayed after registration, and then click on
the [Next] button
Please click on the [Next] button if you are satisfied with the settings.
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 97 頁，共 224 頁
Note
You can change the connection icon and icon name.
→"Changing the connection icon name "
→"Changing the connection icon "
Printing
Try to print from the message pad.
1. Click [File]→[Print]
The [Print] screen will appear.
2. Select wireless printer from under [Select Printer], and then click on the [Print]
button
Printing will commence.
Note
If you have connected to a printer using HCRP or SPP profiles, all future Bluetooth
connections to that printer will be established automatically once you have printed a
document from your PC.
Printing images directly from a digital camera or other device
[BIP]
If you have a printer that supports BIP (Basic Imaging Profile), you can send images dire
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 98 頁，共 224 頁
to a printer to be printed out, without having to perform any special set -up procedure.
→Printing image files on a printer (using icons)
→Printing image files on a printer (by right -clicking the mouse)
Note
Below is a list of file types (extensions) of images that can be printed out directly.
Bitmap (*.bmp)
JPEG (*.jpg; *.jpeg)
PNG (*.png)
Procedure
■Printing image files on a printer (using icons)
1. Turn on the printer
2. Click on the Bluetooth Information Exchanger icon on the Desktop
Note
Alternatively, open Explorer and click on the Bluetooth Information Excha
folder for the same result.
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 99 頁，共 224 頁
The [Bluetooth Information Exchanger] window will appear.
3. Double-click on the [Image Transfer] icon
A list of devices will appear in the [Image Transfer] window.
Note
If your desired printer does not appear in the list, please confirm that the pr
has been turned on, and then click on [Bluetooth] →[Search Devices]
A device search will be performed.
4. Drag and drop the file to be sent on top of the icon of the destination printer
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 100 頁，共 224 頁
The file will be sent to the printer.
If the file has been sent to the printer successfully, the message below will appea
the image will be printed out. Please click on the [OK] button.
The message below will appear if the file transmission was unsuccessful. Please
on the [OK] button to close the message, and repeat the printing procedure.
Note
If the printer does not support the BIP profile, the message below will appe
■Printing image files to a printer (by right -clicking the mouse)
1. Turn on the printer
2. Right-click on the file to be sent, and then click on the destination printer under [
Bluetooth]
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 101 頁，共 224 頁
Note
If your desired device does not appear in the list, please confirm that the de
has been turned on, and then click on [to Bluetooth] →[Search Other Devi
Once the device has been detected, the message below will appear. Please s
the destination device, and click on the [Send] button.
A window indicating that the file is being sent to the printer will appear.
If the file has been sent to the printer successfully, the message below will appea
the image will be printed out. Please click on the [OK] button.
The message below will appear if the file transmission was unsuccessful. Please
on the [OK] button to close the message, and repeat the printing procedure.
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 102 頁，共 224 頁
Note
If the printer does not support the BIP profile, the message below will appe
Printing business card data
[OPP]
If you have a printer that supports OPP (Object Push Profile), you can directly send busin
card data that conforms to the "vCard" standard to a printer and print it out.
→Printing business card data (using icons)
→Printing business card data (by right -clicking the mouse)
Procedure
■Printing business card data (using icons)
1. Turn on the printer
2. Click on the Bluetooth Information Exchanger icon on the Desktop
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 103 頁，共 224 頁
Note
Alternatively, open Explorer and click on the Bluetooth Information Excha
folder for the same result.
The [Bluetooth Information Exchanger] window will appear.
3. Double-click on the [Object Push] icon
A list of devices will appear in the [Object Push] window.
Here, the image will be sent to the target printer.
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 104 頁，共 224 頁
Note
If your desired printer does not appear in the list, please confirm that the pr
has been turned on, and then click on [Bluetooth] →[Search Devices]
A device search will be performed.
4. Drag and drop the business card data to be sent on top of the icon of the destinati
printer
The business card will be sent to the printer.
If the business card has been sent to the printer successfully, the message below w
appear, and the image will be printed out. Please click on the [OK] button.
The message below will appear if the business card transmission was unsuccessfu
Please click on the [OK] button to close the message, and repeat the printing
procedure.
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 105 頁，共 224 頁
■Printing business card data (by right -clicking the mouse)
1. Turn on the printer
2. Right-click on the business card data to be sent, and then click on the destination
printer under [to Bluetooth]
Note
If your desired device does not appear in the list, please confirm that the de
has been turned on, and then click on [to Bluetooth] →[Search Other Devi
Once the device has been detected, the message below will appear. Please s
the destination device, and click on the [Send] button.
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 106 頁，共 224 頁
The business card will be sent to the printer.
If the business card has been sent to the printer successfully, the message below w
appear, and the image will be printed out. Please click on the [OK] button.
The message below will appear if the business card transmission was unsuccessfu
Please click on the [OK] button to close the message, and repeat the printing
procedure.
Listening to music using the stereo headphones
【GAVDP】
【A2DP】 【AVRCP】
This section describes how to use the stereo headphones to listen to your favourite music or o
audio files stored on your PC.
→Configuring the stereo headphones
→Connecting to the stereo headphones
→Listening to music or other audio files
→Playing music using remote control
→Copyright protection function
Configuring the stereo headphones
Procedure
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 107 頁，共 224 頁
1. Right-click on the Bluetooth icon in the task tray, and click on [Add New
Connection].
Note
Alternatively, click [Start] →[All Programs]→[Bluetooth]→[Bluetooth
Settings], and then click on [New Connection] from the [Bluetooth Settings
screen that has opened.
The [Add New Connection Wizard (Welcome to the Add New Connection Wizar
will appear.
2. Switch ON the stereo headphones and activate "Discoverable" mode
Please refer to the user guide for the stereo headphones for further information on
how to operate them.
3. Confirm that [Express Mode] has been selected, and then click on the [Next] butt
The [Add New Connection Wizard (Searching for Bluetooth Devices)] screen wi
appear.
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 108 頁，共 224 頁
Once the search for the devices has ended, the [Add New Connection Wizard (Se
Device)] screen will appear.
4. Select the device name of the stereo headphones from the list, and click on the [N
button
The [Add New Connection Wizard (Searching for Services)] screen will appear.
5. Configure the type and name of the icon to appear once registration is complete,
click on the [Next] button
Please click the [Next] button once you are satisfied with the configuration.
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 109 頁，共 224 頁
The [Add New Connection Wizard (Configure Connection Name)] screen will
appear.
6. Click on the [Finish] button
The settings will be registered, and the icon will appear on the [Bluetooth Setting
screen.
Connecting to the stereo headphones
You can connect to the stereo headphones from the icon registered in [Bluetooth Settings
Please refer to the user guide for information on how to make a connection from the stere
headphones.
Important
Please close the following audio applications before any connection is made betwe
your stereo headphones and PC.
Music/video playback applications
e-Conferencing applications
Voice-recognition applications
Please finish connecting the stereo headphones before launching any of these
applications.
Listening to music or other audio files
1. Playing music or other audio files on your PC
Important
Please confirm the points below if you are unable to hear anything despite
having properly connected the stereo headphones.
Click [Start]→[All Programs]→[Accessories]→[Entertainment]→[Volum
Control].
Remove the tick next to [Mute] if it has been ticked. If the volume is at its
lowest setting, please adjust it to an appropriate level.
Music playback may be interrupted if other Bluetooth devices are currently
connected to your PC. When you are listening to music, it is recommended
the stereo headphones be the only connected device.
Music playback may be interrupted if you are some distance away from the
or if there are any obstructions between you and the PC.
If you are unable to hear any sound out of your stereo headphones while m
or audio is currently playing in a related application, please stop the files be
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 110 頁，共 224 頁
played, open [Sounds and Audio Devices] from the Control Panel, and chan
the default device to "Toshiba Bluetooth Wave."
If you are still unable to hear any sound from the stereo headphones even a
having set "Toshiba Bluetooth Wave" as the default device, please re -laun
application.
2. Finishing listening to music and disconnecting
1. Right-click on the icon for the currently connected mode from [Bluetooth
Settings] on your PC, and click on "Disconnect."
A message confirming the disconnection may appear.
2. Click on the "Yes" button after having followed the instructions in the
message.
The icon will indicate that the device has been disconnected.
Important
Please close the following audio applications before you disconnect the ster
headphones from your PC:
„
„
„
Music/video playback applications
e-Conferencing applications
Voice-recognition applications
Please completely disconnect the stereo headphones before launching any o
these applications.
Please refer to the user guide for information on terminating a connection f
the stereo headphones.
Playing music using remote control
Music applications and video playback applications installed on your PC
(e.g.,"Windows Media Player 9" and "InterVideo WinDVD") may be operated
with the remote control button/switch on your stereo headphones.
The remote control used with the stereo headphones must be compliant with
th Bl t th AVRCP
fil Pl
f t th h d h
id f
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 111 頁，共 224 頁
the Bluetooth AVRCP profile. Please refer to the headphones user guide for
further information.
You can configure the application to be operated using the switch/button
according to the following procedure.
Procedure
1. Double-click on the Bluetooth icon in the taskbar
Launches "Bluetooth Settings."
2. Click on [Bluetooth] →[Select AV Player] from the menu bar
The [Select AV Player] screen will appear.
3. Select the application, and click on the [OK] button
The functions and switch/button that can be operated may differ depending on
the application used for music/video playback as well as the version.
The procedure below can be performed in order to change the position where
the receive command is displayed or to not have the command displayed.
Procedure
1. Double-click on the Bluetooth icon in the taskbar
Launches "Bluetooth Settings."
2. Click on [Bluetooth] →[Select AV Player] from the menu bar.
The [Select AV Player] screen will appear.
3. Select the appropriate item from the pull -down menu of positions
where the receive command is to be displayed, and then click on the
[OK] button.
If the receive command appears but does not function properly, sometimes
the problem may be rectified by changing the setting to "Do not display."
The commands supported by this application are shown below. Please refer to
the headphone user guide for commands that are supported by the stereo
headphones. Problems with operation may be encountered with certain
versions of "Windows Media Player 9" and "InterVideo WinDVD."
[Windows Media Player 9]
Play
Stop
Pause
Next
Previous
Fast forward
Rewind
[InterVideo WinDVD]
Play
Stop
Pause
Next chapter
Previous chapter
Fast Forward
Fast Backward
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 112 頁，共 224 頁
Up
Down
Left
Right
Select
Root menu
Angle
Copyright protection function
A copyright protection function is supported according to the SCMS -T format
as defined in the Bluetooth specifications. Follow the configuration procedure
below to establish connections only with devices that support this function.
Procedure
1. Double-click on the Bluetooth icon in the task tray.
Launches "Bluetooth Settings."
2. Select [Bluetooth] from the menu, and click on [Copyright Protection Setting
The copyright protection dialog will appear.
3. Tick the box next to "Only connect to devices that are copyright -protected u
the SCMS-T format," and click on the OK button.
Using a wireless keyboard
[HID]
This section describes how to connect a Bluetooth -compatible keyboard to a PC.
Setting up the wireless keyboard
Procedure
1. Right-click on the Bluetooth icon in the task tray, and then click on [Add New
Connection]
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 113 頁，共 224 頁
Note
Alternatively, click [Start] →[All Programs]→[Bluetooth]→[Bluetooth Se
and then click on [New Connection] from the active [Bluetooth Settings]
window.
The [Add New Connection Wizard (Welcome to the Add New Connection Wizar
window will appear.
2. Confirm that [Express Mode] has been selected, and then click on the [Next] butt
The [Add New Connection Wizard (Searching for Bluetooth devices)] window w
appear.
Once the program has finished searching for the devices, the [Add New Connecti
Wizard (Device Selection)] window will appear
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 114 頁，共 224 頁
Wizard (Device Selection)] window will appear.
3. Select the device name of the keyboard from [Device List], and then click on the
[Next] button
The [Add New Connection Wizard (Searching for Services)] window will appear
4. Use the wireless keyboard to enter the numbers that appear in [Bluetooth Passke
Code)], and then hit the [Enter] key
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 115 頁，共 224 頁
Once the program has detected the services successfully, connection to the device
registration of settings information will be performed automatically.
The [Add New Connection Wizard (Connection Name Settings)] window will ap
5. Enter the type and name of the icon displayed after registration, and then click on
[Next] button
Please click on the [Next] button if you are satisfied with the settings.
Note
You can change the connection icon and icon name.
→"Changing a connection icon name "
→"Changing a connection icon "
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 116 頁，共 224 頁
The [Add New Connection Wizard (Completing the Add New Connection Wizar
window will appear.
6. Click on the [Finish] button
The settings information will be registered, and an icon will appear in the [Blueto
Settings] window.
Note
Pressing any key on the wireless keyboard will automatically connect it to the PC
thereafter.
Please connect manually if automatic connection is unsuccessful.
Using a wireless mouse [HID]
This section describes how to connect a Bluetooth -compatible mouse to a PC.
Setting up the wireless mouse
Procedure
1. Turn on the wireless mouse, and set it to be connectable via Bluetooth
Please refer to the instruction manual for details on how to operate the mouse.
2. Right-click on the Bluetooth icon in the task tray, and then click on [Add New
Connection]
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 117 頁，共 224 頁
Note
Alternatively, click [Start] →[All Programs]→[Bluetooth]→[Bluetooth Se
and then click on [New Connection] from the active [Bluetooth Settings]
window.
The [Add New Connection Wizard (Welcome to the Add New Connection Wizar
window will appear.
3. Confirm that [Express Mode] has been selected, and then click on the [Next] butt
The [Add New Connection Wizard (Searching for Bluetooth devices)] window w
appear.
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 118 頁，共 224 頁
Once the program has finished searching for the devices, the [Add New Connecti
Wizard (Device Selection)] window will appear.
4. Select the device name of the mouse from [Device List], and then click on the [N
button
The [Add New Connection Wizard (Searching for Services)] window will appear
A message confirming a device connection will appear.
5. Click on the [OK] button
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 119 頁，共 224 頁
The [Add New Connection Wizard (Connection Name Settings)] window will ap
6. Enter the type and name of the icon displayed after registration, and then click on
[Next] button
Please click on the [Next] button if you are satisfied with the settings.
Note
Please use this window to change the connection name and icon.
- Changing the connection icon name
- Changing the connection icon
The [Add New Connection Wizard (Completing the Add New Connection Wizar
window will appear.
7. Click on the [Finish] button
The settings information will be have been registered, and an icon will appear in
[Bluetooth Settings] window.
Note
Clicking on one of the mouse buttons or otherwise operating it will
automatically connect it to the PC thereafter. Please connect manually if
automatic connection is unsuccessful.
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 120 頁，共 224 頁
Exchanging files with a PC or PDA
[FTP]
You can send and receive files other than business card data with a Bluetooth -enabled P
PDA.
Use "File transfer" in the Bluetooth Information Exchanger to exchange files.
Note
The same operations will be valid as long as the PC and PDA support the FTP prof
"File transfer" cannot be used to send or receive business card data. Please instead
"Object Push" to perform these activities.
→Sending files to a PC or PDA (using icons)
→Sending files to a PC or PDA (by right -clicking the mouse)
→Receiving files from a PC or PDA
Procedure
■Sending files to a PC or PDA (using icons)
1. Turn on the PC or PDA
2. Double-click on the Bluetooth Information Exchanger icon on the Desktop
Note
Alternatively, opening Explorer and clicking on the Bluetooth Information
Exchanger folder will produce the same result.
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 121 頁，共 224 頁
The [Bluetooth Information Exchanger] window will appear.
3. Double-click on the [File transfer] icon
A list of devices will appear in the [File transfer] window.
Note
If the desired device does not appear in the list, please confirm that the dev
has been turned on, and then select [Bluetooth] →[Search Devices].
A device search will be performed.
You can also use "Image transfer" when sending individual image files.
4. Use the mouse to drag and drop the file you wish to send over the destination ico
In this case, the file will be sent to a PC named "PC -1".
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 122 頁，共 224 頁
Note
When using "File transfer", you can send individual files as well as entire
folders.
5. Confirm that the file is being sent
The file will be sent to the PC.
Note
When sending files using "File transfer", a message requesting permission t
receive the files may appear on the destination (receiving) device. The cont
the message will vary with the Bluetooth software installed on the destinati
device, so please be sure to follow the instructions provided.
If you are using the Bluetooth Utility, a message similar to the one below w
appear.
If the file has been sent successfully, the message below will appear.
Please click on the [OK] button.
The message below will appear if the file transmission was unsuccessful.
Please click on the [OK] button to close the message, and repeat the procedure.
Note
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 123 頁，共 224 頁
Files that have been sent will be saved in a file transfer shared folder on the
destination device.
Additionally, with "File transfer", you can open the shared folder on the
destination device using Explorer, specify a subfolder, and then send the fil
there.
You can use Properties in the Bluetooth Information Exchanger to change
location of the "Shared folder" on the hard drive.
■Sending files to a PC or PDA (by right -clicking the mouse)
1. Turn on the PC or PDA
Confirm that a Bluetooth connection has been enabled before proceeding.
2. Right-click on the file you wish to send, and then select its destination from [to
Bluetooth]
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 124 頁，共 224 頁
Note
If the desired device does not appear in the list, please confirm that the dev
has been turned on, and then select [to Bluetooth] →[Search other devices]
Once the devices have been detected, the message below will appear. Pleas
select the destination device, and then click on the [Send] button.
3. Confirm that the file is being sent
The file will be sent to the PC.
Note
When sending files using "File transfer", a message requesting permission t
receive the files may appear on the destination (receiving) device. The cont
the message will vary with the Bluetooth software installed on the destinati
device, so please be sure to follow the instructions provided.
If you are using the Bluetooth Utility, a message similar to the one below w
appear.
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 125 頁，共 224 頁
If the file has been sent successfully, the message below will appear.
Please click on the [OK] button.
The message below will appear if the file transmission was unsuccessful.
Please click on the [OK] button to close the message, and then repeat the procedu
Note
Files that have been sent will be saved in a file transfer shared folder on the
destination device.
■Receiving files from a PC or PDA
Your PC is able to receive files that have been saved in the shared folder on the destinati
PC or PDA. Received files will be saved in the shared folder under "File transfer".
1. Turn on the PC or PDA
Confirm that a Bluetooth connection has been enabled before proceeding.
2. Double-click on the Bluetooth Information Exchanger icon on the Desktop
Note
Alternatively, opening Explorer and clicking on the Bluetooth Information
Exchanger folder will produce the same result.
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 126 頁，共 224 頁
The [Bluetooth Information Exchanger] window will appear.
3. Double-click on the [File transfer] icon
A list of devices will appear in the [File transfer] window.
In this case, the file will be received from the PDA named "My Mobile".
4. Double-click on the [PDA-1] icon
The file saved in the shared folder in "My Mobile" will appear.
5. Right-click on the file you wish to receive, and then select "Receive file".
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 127 頁，共 224 頁
The file will be received from a PDA.
Note
With "File transfer", you can send individual files as well as entire folders.
Please right-click on the folder you wish to receive, and select "Receive fo
Subsequent operations should be performed in the same manner as when
receiving individual files.
If the file has been received successfully, the message below will appear.
Please click on the [OK] button.
The message below will appear if the file transmission was unsuccessful. Please
on the [OK] button to close the message, and repeat the procedure.
Note
The received file will be saved in the "Shared folder" under "File transfer"
Bluetooth Information Exchanger
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 128 頁，共 224 頁
You can use Properties under the Bluetooth Information Exchanger to spec
the location of the "Shared folder" on the hard drive.
Sending images to a mobile telephone
[BIP]
You can send image data to a Bluetooth -compatible mobile telephone.
Large images will be automatically reduced to fit on the telephone display screen.
Images are sent using "Image transfer" under Bluetooth Information Exchanger.
Note
The mobile telephone must support the BIP profile.
The following image file formats can be sent and received using "Image transfer":
Bitmap (*.bmp)
JPEG (*.jpg, *.jpeg)
PNG (*.png)
→Sending images to a mobile telephone (using icons)
→Sending images to a mobile telephone (by right -clicking the mouse)
Procedure
■Sending images to a mobile telephone (using icons)
1. Turn on the PC or PDA
Confirm that a Bluetooth connection has been enabled before proceeding.
2. Double-click on the Bluetooth Information Exchanger icon on the Desktop
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 129 頁，共 224 頁
Note
Alternatively, opening Explorer and clicking on the Bluetooth Information
Exchanger folder will produce the same result.
The [Bluetooth Information Exchanger] window will appear.
3. Double-click on the [Image transfer] icon
A list of devices will appear in the [Image transfer] window.
Note
If the desired device does not appear in the list, please confirm that the dev
has been turned on and then select [Bluetooth] →[Search Devices]
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 130 頁，共 224 頁
has been turned on, and then select [Bluetooth] →[Search Devices].
A device search will be performed.
4. Drag and drop the file you wish to send over the destination icon
In this case, the image will be sent to a mobile telephone named "BT -Phone-1".
The image will be sent.
If the image has been sent successfully, the message below will appear.
Please click on the [OK] button.
The message below will appear if the image transmission was unsuccessful.
Please click on the [OK] button to close the message, and repeat the procedure.
■Sending images to a mobile telephone (by right -clicking the mouse)
1. Turn on the mobile telephone
Confirm that a Bluetooth connection has been enabled before proceeding.
2. Right-click on the file you wish to send, and then click on its destination from [to
Bluetooth]
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 131 頁，共 224 頁
Note
If the desired device does not appear in the list, please confirm that the dev
has been turned on, and then select [to Bluetooth] →[Search other devices]
Once the devices have been detected, the message below will appear. Pleas
select the destination device, and then click on the [Send] button.
The image will be sent.
If the image has been sent successfully, the message below will appear.
Please click on the [OK] button.
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 132 頁，共 224 頁
The message below will appear if the image transmission was unsuccessful.
Please click on the [OK] button to close the message, and repeat the procedure.
Sending images to a PC or PDA
[BIP]
You can send image data to a Bluetooth -enabled PC or PDA.
Images are sent using "Image transfer" under Bluetooth Information Exchanger.
Note
The following image file formats can be sent and received using "Image transfer":
Bitmap (*.bmp)
JPEG (*.jpg, *.jpeg)
PNG (*.png)
→Sending images to a PC or PDA (using icons)
→Sending images to a PC or PDA (by right -clicking the mouse)
Procedure
■Sending images to a PC or PDA (using icons)
1. Turn on the PC or PDA
Confirm that a Bluetooth connection has been enabled before proceeding.
Double-click on the Bluetooth Information Exchanger icon on the Desktop
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 133 頁，共 224 頁
2. Double click on the Bluetooth Information Exchanger icon on the Desktop
Note
Alternatively, opening Explorer and clicking on the Bluetooth Information
Exchanger folder will produce the same result.
The [Bluetooth Information Exchanger] window will appear.
3. Double-click on the [Image transfer] icon
A list of devices will appear in the [Image transfer] window.
Note
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 134 頁，共 224 頁
If the desired device does not appear in the list, please confirm that the dev
has been turned on, and then select [Bluetooth] →[Search Devices].
A device search will be performed.
4. Drag and drop the file you wish to send over the destination icon
In this case, the image will be sent to a PC named "PC -1".
The image will be sent.
If the image has been sent successfully, the message below will appear.
Please click on the [OK] button.
The message below will appear if the image transmission was unsuccessful.
Please click on the [OK] button to close the message, and repeat the procedure.
Note
Images that have been sent will be saved in an image transfer folder on the
destination device.
Images received using "Image transfer" in the Bluetooth Information Excha
will be saved in the "Image Box" in "Image transfer".
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 135 頁，共 224 頁
You can use Properties under the Bluetooth Information Exchanger to chan
the location of the "Image Box" folder on the hard drive.
■Sending images to a PC or PDA (by right -clicking the mouse)
1. Turn on the PC or PDA
Confirm that a Bluetooth connection has been enabled before proceeding
2. Right-click on the file you wish to send, and then click on its destination from [to
Bluetooth]
Note
If the desired device does not appear in the list, please confirm that the dev
has been turned on, and then select [to Bluetooth] →[Search other devices]
Once the devices have been detected, the message below will appear. Pleas
select the destination device, and then click on the [Send] button.
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 136 頁，共 224 頁
The image will be sent.
If the image has been sent successfully, the message below will appear.
Please click on the [OK] button.
The message below will appear if the image transmission was unsuccessful.
Please click on the [OK] button to close the message, and repeat the procedure.
Note
When you send images by right -clicking the mouse, the image data that ha
sent will be saved in the image transfer shared folder on the destination dev
This is also the case when you send images using icons.
Exchanging business card data with a PC or PDA
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
[OPP]
2004/11/30
Introduction
第 137 頁，共 224 頁
You can exchange business card data with a Bluetooth -enabled PC or PDA.
Business card data are exchanged using "Object Push" under Bluetooth Information
Exchanger.
Note
Data compliant with the "vCARD" standard are the only type of business card data
to be sent and received with "Object Push".
Business card data can be used by applications such as Microsoft Outlook.
Business card data can be created in vCARD format by Microsoft Outlook and oth
similar applications.
→"Creating business card data in the vCARD format "
You can send business card data directly from Microsoft Outlook.
→"Sending business card data from Outlook "
The OPP profile must be supported by the PC or PDA of the other party.
→Selecting a business card and sending it to a PC or PDA (using icons)
→Selecting a business card and sending it to a PC or PDA (by right -clicking the mouse
→Sending your personal business card
→Receiving a business card from another party
→Exchanging business cards
Procedure
■Selecting a business card and sending it to a PC or PDA (using icons)
Select a business card you wish to send from among all the business card data you have
already received through exchanges with your business or other contacts, and then send i
another party.
1. Turn on the PC or PDA
Confirm that a Bluetooth connection has been enabled before proceeding.
2. Double-click on the Bluetooth Information Exchanger icon on the Desktop
Note
Alternatively, opening Explorer and clicking on the Bluetooth Information
Exchanger folder will produce the same result.
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 138 頁，共 224 頁
The [Bluetooth Information Exchanger] window will appear.
3. Double-click on the [Object Push] icon
A list of devices will appear in the [Object Push] window.
Note
If the desired device does not appear in the list, please confirm that the dev
has been turned on, and then select [Bluetooth] →[Search Devices].
A device search will be performed.
4. Use the mouse to drag and drop the business card you wish to send over the
destination icon
In this case, the business card will be sent to a PC named "PC -1".
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 139 頁，共 224 頁
The business card will be sent.
Note
When you try to send a business card, a message requesting permission to
receive the card may appear on the device belonging to the other party (i.e.
the receiving end). The content of the message will vary with the Bluetooth
software installed on the destination device, so please be sure to follow the
instructions provided. If you are using the Bluetooth Utility, a message sim
the one below will appear.
If the business card has been sent successfully, the message below will appear.
Please click on the [OK] button.
The message below will appear if the business card transmission was unsuccessfu
Please click on the [OK] button to close the message, and repeat the procedure.
Memo
Data that have been sent will be saved in a folder for exchanged business c
on the destination device.
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 140 頁，共 224 頁
You can configure an associated application (Microsoft Outlook etc) to star
automatically when you have received a business card, allowing you to vie
card details.
You can use Properties under Bluetooth Information Exchanger to configur
whether or not you would like such an application to start automatically.
■Selecting a business card and sending it to a PC or PDA (by right -clicking the mouse
1. Turn on the PC or PDA
Confirm that a Bluetooth connection has been enabled before proceeding.
2. Right-click on the business card you wish to send, and then click on its destinatio
from [to Bluetooth]
Note
If the desired device does not appear in the list, please confirm that the dev
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 141 頁，共 224 頁
pp
,p
has been turned on, and then select [to Bluetooth] →[Search other devices]
Once the devices have been detected, the message below will appear. Pleas
select the destination device, and then click on the [Send] button.
The business card will be sent.
Note
When you try to send a business card, a message requesting permission to
receive the files may appear on the device belonging to the other party (i.e.
the receiving end). The content of the message will vary with the Bluetooth
software installed on the destination device, so please be sure to follow the
instructions provided.
If you are using the Bluetooth Utility, a message similar to the one below w
appear.
If the business card has been sent successfully, the message below will appear.
Please click on the [OK] button.
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 142 頁，共 224 頁
The message below will appear if the business card transmission was unsuccessfu
Please click on the [OK] button to close the message, and repeat the procedure.
Note
Data that have been sent will be saved in a folder for exchanged business c
on the destination device.
■Sending your personal business card
You can prepare a business card bearing your name and other details such as your compa
and telephone numbers, and then send it to another party.
Note
Please use Properties under Bluetooth Information Exchanger beforehand to config
which data to use for your own business card.
You can only have one business card registered as your own that is able to be sent.
1. Turn on the PC or PDA
Confirm that a Bluetooth connection has been enabled before proceeding
2. Double-click on the Bluetooth Information Exchanger icon on the Desktop
Note
Alternatively, opening Explorer and clicking on the Bluetooth Information
Exchanger folder will produce the same result.
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 143 頁，共 224 頁
The [Bluetooth Information Exchanger] window will appear.
3. Double-click on the [Object Push] icon
A list of devices will appear in the [Object Push] window.
Note
If the desired device does not appear in the list, please confirm that the dev
has been turned on, and then select [Bluetooth] →[Search Devices].
A device search will be performed.
4. Right-click on the destination icon, and then click on [Send business card To]
In this case, your personal business card will be sent to a PC named "PC -1".
The business card will be sent.
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 144 頁，共 224 頁
Note
When you try to send a business card, a message requesting permission to
receive the files may appear on the device belonging to the other party (i.e.
the receiving end). The content of the message will vary with the Bluetooth
software installed on the destination device, so please be sure to follow the
instructions provided. If you are using the Bluetooth Utility, a message sim
the one below will appear.
Business cards that have been sent will be saved in the Inbox of the destina
party.
If your business card has been sent successfully, the message below will appear.
Please click on the [OK] button.
The message below will appear if the business card transmission was unsuccessfu
Please click on the [OK] button to close the message, and repeat the procedure.
Note
Data that has been sent will be saved in a folder for exchanged business car
the destination device.
■Acquiring a business card from another party
You can use your PC to acquire a business card from a party containing their details.
1. Turn on the PC or PDA
Confirm that a Bluetooth connection has been enabled before proceeding
2. Double-click on the Bluetooth Information Exchanger icon on the Desktop
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 145 頁，共 224 頁
Note
Alternatively, opening Explorer and clicking on the Bluetooth Information
Exchanger folder will produce the same result.
The [Bluetooth Information Exchanger] window will appear.
3. Double-click on the [Object Push] icon
A list of devices will appear in the [Object Push] window.
Note
f h d i dd i
i h li
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
fi
h d
2004/11/30
Introduction
第 146 頁，共 224 頁
If the desired device does not appear in the list, please confirm that the dev
has been turned on, and then select [Bluetooth] →[Search Devices].
A device search will be performed.
4. Right-click on the icon of the party whose card you wish to acquire, and then clic
[Receive business card]
In this case, the business card of the other party will be acquired from a PC name
"PC-1".
The business card will be received.
Note
When you try to acquire a business card, a message requesting permission
send the files may appear on the device belonging to the other party (i.e., o
sending end). The content of the message will vary with the Bluetooth softw
installed on the destination device, so please be sure to follow the instructio
provided.
If you are using the Bluetooth Utility, a message similar to the one below w
appear.
If the business card has been received successfully, the message below will appea
Please click on the [OK] button.
The message below will appear if the business card was unsuccessfully received.
Please click on the [OK] button to close the message, and repeat the procedure.
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 147 頁，共 224 頁
Note
Business card data that have been received will be saved in the Inbox unde
"Object Push".
You can use Properties under the Bluetooth Information Exchanger to set t
location of the Inbox on the hard drive.
■Exchanging business cards
Simultaneously exchange your business card with one belonging to another party.
1. Turn on the PC or PDA
Confirm that a Bluetooth connection has been enabled before proceeding.
2. Double-click on the Bluetooth Information Exchanger icon on the Desktop
Note
Alternatively, opening Explorer and clicking on the Bluetooth Information
Exchanger folder will produce the same result.
The [Bluetooth Information Exchanger] window will appear.
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 148 頁，共 224 頁
3. Double-click on the [Object Push] icon
A list of devices will appear in the [Object Push] window.
Note
If the desired device does not appear in the list, please confirm that the dev
has been turned on, and then select [Bluetooth] →[Search Devices].
A device search will be performed.
4. Right-click on the icon of the party with whom you wish to exchange business ca
and then click on [Object Push]
In this case, the business cards will be exchanged with a PC named "PC -1".
The business card from the party who executed the "Exchange business cards"
command will be sent first.
Note
When you try to send a business card, a message requesting permission to
receive the files may appear on the device belonging to the other party (i.e.
the receiving end). The content of the message will vary with the Bluetooth
software installed on the destination device, so please be sure to follow the
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 149 頁，共 224 頁
instructions provided.
If you are using the Bluetooth Utility, a message similar to the one below w
appear.
A message of confirmation will appear if the card has been successfully sent.
Note
Business cards that have been sent will be saved in the Inbox of the destina
party.
Once your business card has finished being sent, the program will start receiving
business card belonging to the other party.
Note
When a business card is to be received, a message such as the one below m
appear on the device belonging to the other party.
Please click on the [Yes] button if you give permission for the business car
be sent.
A message of confirmation will appear if the card has been successfully received
Note
Business cards that have been received will be saved in the "Inbox" under
"Object Push".
You can use Properties under the Bluetooth Information Exchanger to set t
location of the Inbox on the hard drive.
Using a Bluetooth-compatible camera [BIP]
By connecting a Bluetooth -compatible digital camera to your PC via Bluetooth, you will be
to operate the camera shutter from the PC and transmit the captured images to it as well
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 150 頁，共 224 頁
to operate the camera shutter from the PC and transmit the captured images to it as well.
→Connecting the camera
→Taking pictures
→Viewing images saved on your PC
Connecting the camera
Use the "Remote Camera" tool in the Bluetooth Utility to connect the camera to your PC
Procedure
1. Click on [Start ]→[All Programs]→[Bluetooth]→[Remote Camera]
Note
In Windows 2000, click on [Start] →[Programs]→[Bluetooth]→[Remote
Camera].
The [Remote Camera] window will appear.
2. Turn on the camera, and set it to be connectable via Bluetooth
Note
Different cameras are operated in different ways, depending on the manufa
and model used. Please refer to the instruction manual for further details on
to operate your camera.
3. Click on the [Camera Search...] button
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 151 頁，共 224 頁
The camera will be detected and its icon displayed.
4. Right-click on the camera icon, and select [Connect]
The camera will be connected, and images from the camera will appear on -scree
Taking pictures
By placing the mouse cursor over the on -screen image, the camera's operating window w
appear.
You can operate the camera from this window.
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 152 頁，共 224 頁
Procedure
■Taking a single picture
1. Click on the
button in the operating window.
A single image will be captured and sent to the PC.
■Taking several consecutive frames
1. Click on the
button in the operating window
A succession of images will be captured and sent to the PC.
Note
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30
Introduction
第 153 頁，共 224 頁
The remote camera shutter cannot be operated while the camera is connecte
the PC.
The number of consecutive pictures taken can be set to anywhere between
16
1. In the [Remote Camera] window, click on [Bluetooth]→[Propertie
[Consecutive Image Settings]
The [Change number of consecutive images] dialog box will appe
2. Click on the [<][>] buttons to select the number of consecutive im
to be captured
Important
Images are not only sent to the PC, but are stored in the camera's on -board
memory as well.
Please be aware of the remaining memory capacity when you are taking a l
number of pictures.
Large file sizes are common for high -resolution images, and may take som
to be transferred to the PC.
Viewing images saves on your PC
A "Remote Camera" folder will be created in the "Bluetooth" folder under "My Documen
during initial set -up. A folder bearing the same name as the camera will be created in it,
images will be saved in this folder.
Click the [Explorer] button in the [Remote Camera] window to display the folder where
images have been saved.
file://C:\Documents and Settings\anitachou\Local Settings\Temp\~hh114B.htm
2004/11/30

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Create Date                     : 2004:11:30 09:24:19Z
Modify Date                     : 2005:05:26 16:18:42+08:00
Page Count                      : 77
Creation Date                   : 2004:11:30 09:24:19Z
Mod Date                        : 2005:05:26 16:18:42+08:00
Producer                        : Acrobat Distiller 5.0 (Windows)
Metadata Date                   : 2005:05:26 16:18:42+08:00
Has XFA                         : No

EXIF Metadata provided by EXIF.tools