ATBS Technology AT63 BLE TPMS User Manual

ATBS Technology Co. BLE TPMS

Users Manual

Copyright (C) ATBS Technology Co. R7 版權所有請勿翻印 AT63 sensor User’s guide 1. Introduction This AT63 BLE sensor is a type of sensor that combined TPMS and cellphone. AT63 TPMS external sensor adapts BLE low energy transmission, let driver understand tire situation through cellphone. When the system detects tire pressure or temperature abnormal situation, it (APP) will directly alarm the driver. About This Manual：  The information in this manual is subject to change without notice.  This manual has been created with extra care. In case that you have any comments or questions regarding this manual, please contact your local dealer or our Customer Service Center.  Before operating this set, please fully understand the prerequisite such as specifications or constraints of the hardware and software. We are not responsible and have no liability for any loss, damage or injury as a result of misuse. 2. Check Accessories Model Photograph AT63 sensor Battery Lock nut Wrench Userguide 3. System installation 3.1 Install sensor(battery changeable) 3.1.1 Place batteries into the sensor and screw the top cap off. Please attend to the electrode of the battery. 3.1.2 Remove original valve cap and screw lock nut (1) and will become (2). Screw the Sensor onto valve stem clockwise (3). Screw (1) lock nut back and use wrench to lock tightly (4). (3)(4) steps could effectively prevents sensor from removing. 3.1.3 The sensor label already indicates the sensor ID and its wheel order, please follow the wheel order to install sensors. EX : Sensor Model: AT63 ID:810C619A Note： (1) Beware of the conductivity between the sensor and valve stem. (2) Sensors are supposed to be well locked valve stem to avoid from leaking. (3) Please replace original manufacturer’s sensor battery in case voltage is below 2.7v. (4)External sensor will transmit data every 58~62 seconds when the vehicle is running, and when the vehicle stops, the sensor will transmit data every 148~152 seconds.
Copyright (C) ATBS Technology Co. R7 版權所有請勿翻印 4. iTPMS APP Installation: iTPMS App is for free. Through the iTPMS you can know tire temperature and pressure, sensor battery voltage, and each sensor’s ID. 4.1 Install APP (Take IOS as example) 4.1.1 Download the APP: iTPMS BLE from Apple Store or Google Play. 4.1.2 Go to Setting => General => Bluetooth Page. 4.1.3 Turn on the Bluetooth 4.1.4: Turn on the Bluetooth, and it will scan the devices automatically. 4.1.5 Install battery properly, and then enter to the sensor ID s etting pages. After setting the ID properly, it will read the tire data immediately. 4.2 App Operating 4.2.1 Click below ID, and enter the ID learning page, start to learn the sensor ID. Note: When the above BLE words light up, then it represents it detects AT63’s signal already. 4.2.2 Place batteries into the sensor properly. When sensor detects pressure, ID will turn to red to alert the user. 4.2.3 Enter Setup page, users can set up the unit and limit of tire pressure and temperature.
Copyright (C) ATBS Technology Co. R7 版權所有請勿翻印 4.2.4 In the meantime, this TPMS program also afford user to manual input the ID function and scanning QR function, please refer to the following steps: A) Manual key in ID steps: 1) Click the right upper “Edit” 2) Turn to New page 3) Click the blank and appear keyboard, enter the ID and click save. 4) Click “Yes” Note: Click Cancel and back to learn ID page. 5) Click SAVE and then click yes, and it’s done. B) Steps for scanning QR Code: 1) Click middle QR buttom 2) Enter into ID Read page, and click the blank to start scanning QR code. And then click save. 3) Click “Yes” 4) Click SAVE and then click yes, and it’s done. Note: Be sure you already turn on the Bluetooth 5. Specification 5.1 AT63 Sensor Model AT63 Operation Temperature -40℃~ 85℃ Operation Humidity 100%, IP 68 Total Outer meter 22±0. 2mm Total Height 21±0. 2mm

Navigation menu