Abocom Systems BSR202 Bluetooth Stereo Receiver User Manual bsr202 receiver indd

Abocom Systems Inc Bluetooth Stereo Receiver bsr202 receiver indd

Users Manual

1—Check the package contents2—Charge the battery3—Turn on the power4—Pair (make connection) with receiverUnpack the Bluetooth Stereo Receiver and check that the following items are included:The battery lasts eight hours and is re-charged using the power adapter or the USB cable. To recharge:Plug the USB cable into the DC jack on the Bluetooth Stereo Receiver and connect the other end to your PC.orPlug the power adapter into the DC jack on the Bluetooth Stereo Receiver and con-nect the other end to an electrical outlet.To turn on the power, press and hold the power until the power LED lights blue.To turn off the power, press and hold the power button until the power LED turns off.The Bluetooth Stereo Receiver can be used with a bluetooth transmitter or Bluetooth Audio Dongle. On fi rst use, the devices must be paired. To pair the devices.1. Connect your receiver to an audio device.2. Turn on the power on your Bluetooth Stereo Receiver. 3. Turn on the power on the transmitter. Recharging takes 90 minutes.Bluetooth StereoReceiverQuick GuidePower AdapterUSB CableBlue LED power is onBlue fl ashing LED connected to device Red LED battery is charging, turns off when chargedRed fl ashing LED battery is low, recharge before LED turns offPower buttonMute on/offDC jack Volume +/-Power/Batter LEDLine-out jack Earphone jack Play
5—Wait for devices to connect90 secondsThe devices connect (pair) after 90 seconds.6—Using with your mobile phoneThe Bluetooth Stereo Receiver can be used with a Bluetooth enabled mobile phone.To pair with your phone1. Enable Bluetooth on your phone (refer to the phone’s user manual). 2. Turn on the Stereo Receiver. 3. In the phone’s Bluetooth menu, search for devices.4. Select Stereo Receiver.5. Enter the PIN code “0000”.Answering callsTo answer a call, push the play button.To end a call, push the power button.7—Troubleshooting8—Specifi cationsSerial number & Firmware version:StandardsBluetooth specifi cation V1.2 compliant.Bluetooth A2DP profi le (AV Profi le)Bluetooth AVRCP profi le Headset and Hand freeTx Power0.25 ~ 2.5mW (Bluetooth Power Class II)Rx Sensitivity< -80dBm (BER 0.1%)Distance> 10m (open space)Audio Streaming FormatSBC 48.000 kHzAudio Frequency Range20Hz ~ 22 kHzAudio S/N> 85dBAudio THD< -83dBAudio Output Power> 20mWrmsPower supplySupply by integrated rechargeable battery cell. Music plays : > 8 hrs.Physical Specifi cation:Dimension: 65.5 mm x 35 mm x 22.5 mmEnvironmental Range:Operating temperature:-10 ~ +50 degrees centigradeHumidity: Relative humidity 0 ~ 95%If the Bluetooth Stereo Receiver does not work, try the following:- Ensure connecting devices are charged- Turn off all devices and then turn them on in the order shown in this guide- Ensure devices are within the 10-meter range?
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Navigation menu