Abocom Systems SDW11G SDIO Wireless LAN Card User Manual SDW11g

Abocom Systems Inc SDIO Wireless LAN Card SDW11g

Users Manual

  1INSTALLING THE DRIVER Installation of the SD WLAN Card Driver to the Pocket PC using Microsoft Active Sync® 1. Connect your PDA to your computer and make sure Active-Sync® has established a connection between the two devices. 2. Insert the included CD-ROM to your PC. The main screen will appear, click Install Driver to start driver installation.
2   Note: Do not insert the SD WLAN Card into the card slot of your PDA until the Driver installation has been performed.  3. Click “YES” to continue the installation.     4. Click “OK” to complete the driver installation.  ACCESSING THE WLAN UTILITY 1. Insert the SDIO Wireless LAN Card into the SD slot of your PDA 2. Go to Start > Settings  >  Connections  tab  >  Wireless  Ethernet  to  access the Windows CE built-in WLAN utility
3 CONFIGURING WLAN UTILITY Select an available AP or router from the list and tap Connect to make a connection.
4 Wireless tab Wireless Network  Select an available network device from the list and tap Connect. Network to access  Select the type of network access from the pull-down list. All available: A group of wireless devices communicating with both access points and network adapters. Only access points: A group of wireless devices communicating directly with only access points. Only computer-to-computer: A group of wireless devices communicating directly with each other without the use of an access point. Automatically connect to non-preferred networks  Tap the checkbox to enable this function, if the Automatically connect to non-preferred networks is enabled, your device will detect all the new networks for you to configure.
5
6  Network Adapters tab My network Card connects to  Tap Work or The internet from the pull-down menu. Work: Connects to the network in your office. The internet: Connects to your ISP at home. Tap an adapter to modify settings  Tap an adapter from the list to enter its configuration screen.  If SDIO 802.11g Adapter is tapped, the following screen will appear for you to configure:
7
8 IP Address tab Use server-assigned IP address  To use DHCP, tap User assigned-IP Address. The Wireless Router will act as a DHCP server. An IP Address will be obtained from the Wireless Router.
9 Use specific IP address  IP Address: Enter the IP address (within the range of the wireless router’s IP address, for instance, if the IP address of the router which you wish to connect is 192.168.1.254, you may enter the IP address here from 192.168.1.1 to 192.168.1.253 ). Subnet mask: The Subnet Mask must be the same as that set on your Ethernet network. Default Gateway: Enter the IP address of your network’s gateway. The gateway is the device that enables communication between your computers and the Internet. In most cases, your router acts as your gateway.
10
11 Name Servers tab DNS  Enter the IP address of your ISP's server, which translates the names of websites into IP addresses. Alt DNS  The secondary IP address of your ISP’s server. WINS  The Windows Internet Naming Service (WINS) converts NetBIOS names to IP addresses. If using a WINS server, please enter that server’s IP address. Otherwise, leave this field blank. Alt WINS  The secondary IP address of your WIN server.    M73-APO11-270
12 Federal Communication Commission Interference  Statement  This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference  in a residential  installation. This equipment generates, uses  and  can radiate radio frequency energy  and, if not installed and used in accordance with the instructions, may   cause  harmful  interference  to  radio  communications.  However,  there  is  no  guarantee  that interference  will  not  occur  in  a  particular  installation.  If  this  equipment  does  cause  harmful interference to  radio or  television reception,  which  can  be  determined  by  turning the  equipment off  and  on,  the  user  is  encouraged  to   try  to  correct  the  interference  by  one  of  the  following measures:  Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect  the  equipment  into  an  outlet  on  a  circuit  different  from  that  to  which  the  receiver  is connected. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.  FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.   This device  complies  with Part  15 of  the FCC  Rules.  Operation  is  subject  to  the following  two conditions:    (1)  This device  may not  cause  harmful  interference,  and (2)  this  device  must accept any interference received, including  interference that may cause undesired operation.   This transmitter must not be co-located or operating in conjunction with any other antennaor transmitter.12

Navigation menu