Acroprint Time Recorder 1207 Proximity Reader User Manual 111303 Qstart

Acroprint Time Recorder Company Proximity Reader 111303 Qstart

User Manual

You will need the following items:•  Attendance Rx™ software(may already be installed, PN: 08-0137-000)•  ATRx ProxTime™(ATRx 10 Proximity Terminal, PN: 01-0206-000)•  50 ft. RS232 ATR Communications Cableprovided by Acroprint (PN: 72-0146-004)•  RJ11/DB 9-pin ATR Serial Adapterprovided by Acroprint (PN: 63-0163-003)•  DC 12V Power Adapter(PN: 56-0126-000)•  15 Proximity Badges(PN: 14-0123-002)Attendance Rx must be installed prior to initial setupand connection of ATRx10 proximity terminal.  Ifsoftware is already installed proceed to step 2 ofQuick Start.  If not, install  Attendance Rx software byinserting CD into CD-Rom.  Follow and complete theinstallation wizard.To ensure PC meets the minimum system requirements,see product box or refer to www.acroprint.com.ATRx ProxTime Quick Startwww.acroprint.com1.  Make sure PC is completely shut off.To avoid damage to the PC port; PC power must becompletely shut off prior to attaching the ATR adapterand ATR communications cable.2.  Connect ATR adaptor and ATR communicationscable (this may already be connected at the factory).3.  Connect the ATR adapter to the serial port on theback of your PC.4.  Connect ATR communications cable to the whiteport on the back of the ATRx10 proximity terminal.** Do not connect to telephone wall outlet.** Do not connect to modem port.5.  Plug DC 12V Power Adapter into the back of theATRx10 proximity terminal.  ATRx10 will display PCon the LCD screen until your PC is powered ON andthe Attendance Rx program is running.Power on your PC and Attendance Rx should berunning.  To confirm software is running, a SystemTray Icon will appear in the bottom right-hand cornerof  your computer desktop screenTo enable ATRxTerminal Manager, rightclick the System Trayicon, select EnableTerminal Manager.Software may automatically locate the PC serialport.  After the start-up sequence the Time and Dayof Week will display on the ATRx10 screen.Note:  If the connection fails the letters PC will dis-play on ATRx10 screen.  If this occurs, repeat stepsin Quick Start step 2 to ensure connections arecorrect and proceed to Trouble Shooting portion onthe reverse side of the Quick Start.Getting Started Connect ATRx10to IBM Compatible PCPower ConnectionVerify Terminal isCommunicating with PCAfter following these steps, your set-upshould look like this diagram.*Use enclosed wall template and four screwsto mount unit to wall stud.
ATRx ProxTime Quick Startwww.acroprint.comVerify you are using the equipment supplied by  Acroprint: connections cable, serial adapter, poweradapter.Verify program is running.  Refer to Step 2 of Quick Start (reverse side of this document).Check connections on the back of the PC to confirm the adapter and cable supplied by Acroprint aresecurely attached to a serial communications port.Confirm the cable supplied by Acroprint is plugged into the correct port on the ATRx terminal.Cycle the power to the ATRx terminal by unplugging the DC 12V power adapter from wall outlet fortwo to five seconds, then plug back into the wall outlet.Restart Windows.  Once computer login is complete, verify program is running (Refer to Step 2 ofQuick Start).Any additional questions, contact Acroprint’s Technical Support Department.WEB:  www.support.acroprint.com FAX:  919.872.5967TOLL FREE: 1.800.334.7190, option 3. EMAIL: supportdept@acroprint.comConnecting Additional TerminalsTroubleshooting the ATRx10and ATRx20 Terminal ConnectionsNOTE:  This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 ofthe FCC Rules.  These limits are designed to provide reasonable protection against harmful interference when the equipment isoperated in a commercial environment.  This equipment generates, uses, and can radiate radio frequency energy and, if notinstalled and used in accordance with the instruction manual, may cause harmful interference to radio communications.Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required tocorrect the interference at his own expense.This Class A digital apparatus complies with Canadian ICES-003.  Cet appareil numerique de la classe A est conforme a lanorme NMB-003 du Canada.Make sure PC power is ON and the Attendance Rx software program is running(see step 2 on reverse side of  this Quick Start ).Plug communications cable into the available black port on the ATRx10 terminal.  Connect the other endof the cable into the first black port on the ATRx20 terminal.*This cable is design for  RS485 communications.  It is available for purchase through Acroprint, please callfor more information (1.800.334.7190).Insert the Terminator Plug into the remaining open RS485 port on the last ATRx20 terminal that is on thechain of terminals.Plug DC 12V power adapter into the back of the ATRx20 and the wall outlet.Time and Day of Week will display on the screen of the ATRx 20 terminal, if connection is established.

Navigation menu