Ademco 0600906 Microwave/PIR motion sensor User Manual 505134401E

Download:
Mirror Download [FCC.gov]
Document ID	1017469
Application ID	pCtP6uJcR6MkHatkDZqRRA==
Document Description	User manual 1 of 2
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	51.13kB (639113 bits)
Date Submitted	2008-10-20 00:00:00
Date Available	2008-10-20 00:00:00
Creation Date	2001-04-12 14:05:55
Producing Software	Acrobat Distiller 4.0 for Windows
Document Lastmod	2008-09-17 18:09:15
Document Title	505134401E
Document Creator	Adobe PageMaker 6.52
Document Author:	slauro

DT-900 Series DUAL TEC® Motion Sensor Supplemental Information
MOUNTING LOCATION
Aim the sensor toward the interior of the room, away from windows, moving machinery, and heating/
cooling sources.
DT-900
DT-906
Make sure the sensor has a clear line-of-sight to all areas you wish to protect. If the PIR is blocked, the
unit will not alarm.
TAMPER
The sensor covers and wall mounting are tamper protected. A screw must be installed in the wall
to utilize the tamper feature.
WIRING
Reverse polarity will not damage the sensor.
Knockouts are provided to allow wire entry via 1/2” EMT or surface wiring conduit.
NOTE: For proper wiring methods, refer to the National Electrical Code NFPA 70.
INFORMER MODE
The INFORMER circuit counts the number of events registered by both the microwave and PIR
technologies, and uses the resulting ratio to determine if either technology is working properly or is
misapplied. Establish the INFORMER mode using switch S2. (See Step 7.)
Mode 1: Set S2 to position 1. In Mode 1, 32 PIR events without a microwave event will cause the
unit to go into PIR INFORMER. 128 microwave events without a PIR event will cause the unit to go
into microwave INFORMER. One LED indication does not relate to one PIR event.
Mode 2: Set S2 to position 2. In Mode 2, 16 PIR events without a microwave event will cause the
unit to go into PIR INFORMER. 16 microwave events without a PIR event will cause the unit to go
into microwave INFORMER. One LED indication does not relate to one microwave event.
Figure 1
DT-900 Printed Circuit Board
NOTE: The Mode 2 setting is not recommended. Use only if fast INFORMER activation
is required.
When an INFORMER condition occurs, the trouble relay opens, and the LEDs display an INFORMER trouble code. The sensor performs
a self-test within the hour to determine if the problem is internal.
If a self-test error is detected, the self-test LED pattern, all three LEDs flashing, replaces the INFORMER LED pattern.
10
12
14
50
90
120
200
1.8
2.4
3.7
4.3
15
27
37
61
INPUT MODES
The DT-900 Series accommodates several international operating requirements using two operating modes—Standard mode with
remote LED enable and Command Input capability or European 2-Wire CENELEC mode (INPUT 1 and INPUT 2). For Standard
Mode, remove jumper J4 and install jumper J6. For CENELEC mode, remove jumper J6 (See Figure 1).
Table 2 CENELEC Mode—J6 Removed
Input Condition
HIGH/Not connected
LOW
Operating Mode
Alert
INPUT 1
LEDs Disabled
LEDs Enabled
INPUT 1
INPUT 2
Normal operation
Self-test
INPUT 2
Local Test Standby Remote Test
high
high
low
high
high
low
low
low
NOTE: For Standard Mode/INPUT 2 (remote self-test) use only—install jumper J4.
Operating Mode
Local Test
Enabled
On
Enabled
No
No
Enabled
Standby
Disabled
Off
Frozen
No
No
Enabled
Remote Test
Disabled
On
Enabled
Yes
No
Disabled
Disabled
Enabled
Enabled
Disabled
Anti-Mask
The DT-900 Series anti-mask feature detects attempts to block or cover the sensor by sending an active infrared beam out into the
sensor’s field-of-view, at regular 8 second intervals. If the DT-900/DT-906 is blocked or covered (i.e. with a box or fabric) the beam
is reflected back to the sensor. After two consecutive reflected beams, the sensor signals a trouble condition—green and red
LEDs flash rapidly and the mask relay opens.
INFORMER Conditions
Table 3 describes two trouble alerts which are reported by the INFORMER circuit. To use this troubleshooting matrix:
1) Find the trouble alert that describes the condition of the walk-test LEDs (with no motion in the area).
2) Walk-test the sensor, carefully watching the reaction of the diagnostic LEDs.
3) Refer to the Possible Causes column of the matrix for an explanation of the way in which the diagnostic LEDs
reacted to the walk-test.
Table 3 INFORMER
Troubleshooting Matrix
Reaction of LEDs
Condition of LEDs
to Walk-Test
with No Motion
PIR ALARM MW
PIR ALARM MW
(Green) (Red) (Yellow) (Green) (Red) (Yellow)
Table 4 Cenelec Functions
Alert
Disabled
On
Enabled
Yes
Only when Entering
Disabled
To recover the LED pattern, first open the Top Cover (see Step 2). Using a small screwdriver, momentarily short circuit the two Self-Test
pads located on the printed circuit board (see Supplemental Information, Figure 1). The trouble LED pattern will be re-displayed.
Short the pads with the screwdriver again to clear the LED pattern and initiate a self-test.
If no self-test error occurs, the unit continues to display the INFORMER LED pattern and relay remains open. The problem is
misapplication. Walk-test the sensor to pinpoint the cause. (Refer to Troubleshooting Table 3.)
Walk Test LED’s
Microwave Oscillator
Alarm Outputs
Alarm Memory Activated
Alarm Memory Reset
Alarm Memory Displayed
(Red LED flashing)
Trouble
Trouble Memory
If the LED pattern disappears before you see it, you can retrieve the pattern. The trouble memory feature stores the last LED pattern from
a self-test detected problem or an INFORMER condition.
Disabled: To disable INFORMER function, set S2 to the open position.
Table 1 Standard Mode—J6 Installed
Feet
Meters
Remote Test Mode
causes the unit to enter a
remote self-test (ongoing
self-test). The Anti-Mask
Output becomes a “test
running” output and
remains open for the
duration of the test. If the
unit passes all the selftests, the alarm relay is
activated for one second.
MW environmental problem
MW unstable
MW range too long
PIR was blocked
RATIO
IMBALANCE
PIR range too short
PIR aimed wrong
PIR not reporting
(Pattern disappears)
RATIO
MW range too short
IMBALANCE MW not reporting
LED Legend:
= LED is Flashing Slow
Patterns for: DT-900
27 m (90’) Range
TOP VIEW
Barrier Lens—All Zones
Patterns for: DT-906
61 m (200’) Range
RATIO
IMBALANCE
NOTE: If you enter the detection pattern and the LEDs
go off, you can retrieve the
LED pattern to pinpoint the
problem. Refer to Trouble
Memory above.
PIR environmental problem
RATIO
IMBALANCE PIR unstable
MW range too short
Vertical Adjustment
Various mounting locations may require fine vertical adjustment (e.g. uneven walls or floors, etc.). During the walk-test, if the PIR is shortranged, turn the Vertical Adjust Screw counterclockwise. If the PIR is over-ranged, turn the Vertical Adjust Screw clockwise.
(See Step 5.)
DETECTION PATTERNS
Possible
Causes
(Pattern disappears)
TROUBLESHOOTING
Self-Test
The sensor microcontroller automatically performs a series of self-tests in the following instances: when the unit is powered up, when
the tests are installer initiated, upon Command Input, or every hour during normal operation. When a self-test error occurs, the Trouble
relay opens and all 3 LEDs flash until the problem is corrected. If the problem persists and the LEDs continue to flash, the unit is defective
and must be returned for repair.
Type of
Problem
=LED is OFF
Patterns for: DT-900
15 m (50’) Range
TOP VIEW
Wide Angle Lens
TOP VIEW
Wide Angle Lens
SIDE VIEW
Barrier Lens—All Zones
TOP VIEW
Barrier Lens—All Zones
Pattern for: DT-906
37 m (120’) Range
Indicates Detection Area
SIDE VIEW
Barrier Lens—All Zones
SIDE VIEW
Wide Angle Lens
SIDE VIEW
Wide Angle Lens
PRODUCT SPECIFICATIONS
Range:
DT-906
37 m x 3 m / 61 m x 5 m
120' x 10' / 200' x 15'
DT-900
15 m x 12 m / 27 m x 21 m
50' x 40' / 90' x 70'
Alarm relay:
Energized Form C
25 VDC, 125 mA
22 ohm series protection resistor
Power requirements:
10 - 15 VDC
50 mA (max) at 12 VDC
AC Ripple: 3V peak-to-peak
at nominal 12 VDC
Trouble relay:
De-energized Form B
(Normally closed)
30 VDC, 25mA
Mask relay:
De-energized Form B
(Normally closed)
30 VDC, 25mA
Input 1 & 2:
Self-test initiate
Active low 0 to 1.5V
Inactive high 5 to V+
Sensitivity:
2 - 4 steps within field of view
Tampers:
PIR white light immunity:
Wall, top & bottom covers
30 VDC, 25 mA (NC)
RFI immunity:
PIR fields of view:
6500 Lux
30 V/m, 10 MHz - 1000 MHz
Copyright 2001 IntelliSense.
5-051-344-00 Rev E
61 m (200’) Range
2 long
6 intermediate long
4 intermediate
4 intermediate lower
8 lower
2 down
37 m (120’) Range
6 long
4 intermediate long
4 intermediate
8 lower
2 down
27 m (90’) Range
18 long
18 intermediate long
16 intermediate
12 intermediate lower
8 lower
2 down
15 m (50’) Range
18 long
16 intermediate long
12 intermediate
8 lower
2 down
Microwave frequencies:
X band
Operating temperature:
0o to 49o C / 32o to 120o F
Relative humidity:
5% to 95% relative humidity
(non-condensing)
Dimensions:
20 cm x 16.5 cm x 15.2 cm
8” x 6 1/2” x 6”
Weight:
1.36 kg / 3 pounds
Packaged product:
1.6 kg / 3.5 pounds
Approvals/listings:
FCC certified
Industry Canada
UL listed
ULC listed
IMPORTANT: DT-900 Series sensors should be tested at least once each year to ensure proper operation.
FCC NOTICE: This equipment has been tested and found to comply with the limits for a field disturbance sensor, pursuant to
Part 15 of the FCC Rules. The user is cautioned that changes or modifications not expressly approved by IntelliSense could void
the user's authority to operate this equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
IC Notice: Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired operation of the device.
Note: The ULC label or listed marking on a product is the only evidence provided by Underwriters Laboratories of Canada to
identify products that have been produced under the Listing and Follow-Up Service.
IntelliSense, DUAL TEC and INFORMER are registered trademarks of Honeywell, Inc.
DT-900 Series DUAL TEC® Motion Sensor for Commercial
and Light Industrial Applications—Installation Instructions
Step 1
Select mounting height.
30 cm (12”) minimum
Step 2
Carefully push screwdriver into slots
to disengage latches and open top
cover.
Step 3
Firmly insert screwdriver into slot in
arrow and rotate PIR Mirror Selector
to the correct range.
Step 4
Set switch S4 to establish microwave
range.
DT-906
4 m (12’)
Optimal
Mounting
Height
RANGE
Switch S4
MIRROR
Selector
DT-906
61 m (200’)
OPEN*
200’ *
DT-906
DT-900
37 m (120’) CLOSED
27 m (90’) OPEN*
90’ *
DT-900
15 m (50’)
50’
MODEL
2 m (6’)
DT-900
CLOSED
120’
*Factory default setting.
Step 5
Locate correct sensor range scale
and rotate Vertical Adjustment Screw
until the diamond corresponds to the
sensor mounting height (coarse
adjust).
Step 6
Set switch S3 to establish the sensitivity best suited to your application.
SENSITIVITY
NOTE: Fine adjust may be needed during
walk-test. See Supplemental Information.
Step 9
Unfasten screws and remove mounting plate from sensor.
Step 7
Select INFORMER® mode with switch
S2, if desired. (See Supplemental
Information).
Step 8
Carefully push screwdriver into slot
to disengage latch and remove
bottom cover.
Step 11
Install M5 (#10) screw in wall 1.9 cm
(3/4”) below mounting screw, as
shown, for tamper activation.
Step 12
Pull about 30 cm (12”) of wire from
wall through the opening in the
mounting plate and route wire to the
terminal strip.
S3
HIGH
NORMAL
N*
LOW
L**
*Factory default setting. **Not connected
**Not recommended for DT-906
Step 10
Attach mounting plate to wall at
desired height, using four fasteners
(not supplied).
1.9 cm (3/4”)
Step 13
Hang the sensor on the mounting
plate hooks and fasten with the two
mounting plate screws.
Step 14
Wire the unit
as shown.
Use 2.0 - 0.3 mm2
(14-22 AWG).
INPUTS 1 & 2
Standard or
Cenelec mode
MASK DETECT (NC)
30 VDC, 25 mA
Step 15
Loosen horizontal locking screw in
sensor support base.
TROUBLE (NC)
30 VDC, 25 mA
Step 16
Grasp housing and rotate it to the
desired position (coarse adjust). If
fine adjust is needed see Steps 2022.
TAMPER (NC)
30 VDC, 25 mA
END-OF-LINE
Connect terminating
resistors on last unit
NOTE: Secure
wires to
mounting plate
with tie wraps.
Step 17
Apply power to sensor and prepare
for walk-test.
Wait 90 seconds for power-up selftest to run. All LEDs will flash.
PIR ALARM MW
(Green) (Red) (Yellow)
ALARM OUTPUTS
(NO, NC, COM)
25 VDC, 125 mA,
Form C relay
NOTE: Reference marks = 5° change.
POWER
10 - 15 VDC
50 mA (max) at 12 VDC
Step 18
Turn the microwave potentiometer
counterclockwise to decrease the
microwave range to minimum.
During walk-test, gradually turn the
potemtiometer clockwise increasing
microwave sensitivity until the
desired range is obtained.
NOTE: LEDs flashing after 90 sec. = defective
Step 19
Walk-test the sensor to check for
adequate detection coverage and to
verify the sensor is fully functional.
Two to four normal steps should
make the LEDs light and trigger an
alarm.
Step 20
For finer horizontal adjustments,
loosen the PIR horizontal fine locking
screw on PCB.
NOTE: If an on-going self-test problem, mask
condition or an INFORMER condition occurs,
the LEDs display a pattern that identifies the
trouble. See Supplemental Information
(Table 3).
NOTE: When there is no motion in the
detection area, all three LEDs should be off.
Step 21
Rotate horizontal fine adjust knob to
the desired position.
NOTE: Fine adjustment allows for small
changes (3 degrees right or left) between
coarse settings.
Step 22
Tighten horizontal fine locking screw
on PCB.
Step 23
Tighten horizontal locking screw in
sensor support base.
Step 24
Remove jumper at J5, on the PCB,
to disable the LEDs after walktesting.
Step 25
Complete installation by closing top
cover and replacing bottom cover.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Create Date                     : 2001:04:12 14:05:55Z
Creator Tool                    : Adobe PageMaker 6.52
Modify Date                     : 2008:09:17 18:09:15-07:00
Metadata Date                   : 2008:09:17 18:09:15-07:00
Format                          : application/pdf
Description                     : 505134401E
Creator                         : slauro
Title                           : 505134401E
Keywords                        : 
Producer                        : Acrobat Distiller 4.0 for Windows
Document ID                     : uuid:43ff2859-08f2-4ff6-bbf6-e710d9443751
Instance ID                     : uuid:6c764bd9-cfc6-42f8-92ea-5ff23e08b1b1
Page Count                      : 2
Subject                         : 505134401E
Author                          : slauro

EXIF Metadata provided by EXIF.tools