Ademco 8DL5800PIR-OD Security Transmitter User Manual

Honeywell International Inc. Security Transmitter 5890 OD Wireless Outdoor Motion Sensor

a href="https://usermanual.wiki/Ademco" itemprop="url"> Ademco >

User manual

5800-OD Wireless Outdoor Motion Sensor – Installation Instructions GENERAL INFORMATION The Honeywell 5800-OD Wireless Outdoor Motion Sensor (referred to as the 5800-OD) combines the convenience of wireless technology with a full featured outdoor PIR motion sensor. The major features are highlighted below:  Immunity to bright light disturbances from headlights, sunlight, and other bright light sources.  Very low current draw.  Discriminates both large and small animals to reduce false alarms.  Selectable detector range and angle.  Battery saving circuit allows for a 5 or 120 second period of inactivity before being reactivated.  Tamper detection. SPECIFICATIONS Detection Method Passive Infrared Initial Warm Up ~ 2 minutes Mounting Height 0.8 - 1.2m (2.7 - 4ft) wall or pole Range Adjustable up to 12m (40ft) Pattern 90° pattern consisting of 13 zones. This pattern can be adjusted in 15° incre-ments from center up to 45°. Sensitivity 2.0° C at 0.6m/s (3.6° F at 2.0ft/s) Detection Speed 0.3 - 1.5m/s (1 - 5ft/s) Operating Voltage 6 VDC (uses 4 lithium 1.5VDC AA cells) Current 3mA max (during walk test) 10uA (standby) Battery Saving Timer Adjustable 120sec or 5sec Alarm Period ~ 2.5 seconds LED Indicator Enabled during a walk test. Disabled for normal operation. Weatherproof IP54 compliance Operating Temperature – 20 to + 50 ° C (– 4 to +122° F) Humidity 95% Max Accessories (included) Pole mounting kit, screw kit, detection masking strips. INSTALLATION (refer to the Component Identification Diagram on page 5) 1 Select the Mounting Position  Avoid strong sunlight into the sensor's field.  Avoid moving or swaying trees and bushes.  Orient the detector so that intrusion passes across the detection field, not into the sensor.  Allow 110mm (4.4") above the sensor to enable opening the cover.  Choose an installation height of 0.8m to 1.2m (2.7 to 4ft).  Ensure the sensor can be mounted on a perpendicular wall or pole that would make its detection pattern parallel to the ground. Parallel 2 Prepare the Sensor for Mounting 1. Loosen the Captive Lock Screw and remove the Cover. 2. Remove the four (4) screws fastening the Detector to the Back Box. 3. Remove Detector from the Back Box. 3 Install / Replace the Battery IMPORTANT:  Use only lithium batteries.  Use four (4) lithium 1.5VDC AA cells. (Energizer L91 or equivalent.)  Observe polarity.  Mark the date of replacement on the batteries. 1. If necessary, loosen the Captive Lock Screw and lift Cover off. Then, remove 4 screws that secure the Detector to the Back Box. 2. Observe the proper polarity and replace the batteries. Ensure positive side of battery is pointing away from the springs. 3. For reference, mark the date of replacement on the batteries. PLEASE GO TO PAGE 6 FOR FCC / IC STATEMENTS
Download:
Mirror Download [FCC.gov]
Document ID997586
Application ID1PDvEQs+vWjU33BgDD5ToA==
Document DescriptionUser manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize61.16kB (764492 bits)
Date Submitted2008-09-09 00:00:00
Date Available2008-09-09 00:00:00
Creation Date2008-05-02 08:52:17
Producing SoftwareAcrobat Distiller 6.0.1 (Windows)
Document Lastmod2008-08-15 11:08:26
Document Title5890-OD Wireless Outdoor Motion Sensor
Document CreatorAcrobat PDFMaker 6.0 for Word
Document Author: E365313
FCC ID Filing: CFS8DL5800PIR-OD

Navigation menu