Ademco 8DL5816OD-1 Wireless Outdoor Sensor User Manual 5816OD Wireless Outdoor Sensor

Download:
Mirror Download [FCC.gov]
Document ID	1428109
Application ID	bVS0CAVuiRi4DlvyotC5vw==
Document Description	manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	16.71kB (208864 bits)
Date Submitted	2011-03-08 00:00:00
Date Available	2011-09-05 00:00:00
Creation Date	2011-02-23 11:36:25
Producing Software	Acrobat Distiller 9.4.2 (Windows)
Document Lastmod	2011-03-01 11:04:06
Document Title	5816OD Wireless Outdoor Sensor
Document Creator	Acrobat PDFMaker 9.1 for Word
Document Author:	E365313

SEE THE BOTTOM OF PAGE 2 FOR FCC & IC
STATEMENTS
5816OD Wireless Outdoor Sensor – Quick Installation Guide
For Online Support visit: http://www.security.honeywell.com/hsc/resources/MyWebTech/
WARRANTY For the latest warranty information go to: http://www.security.honeywell.com/hsc/resources/wa/
General Information and Component Identification
COMPONENT IDENTIFICATION
SENSOR
SENSOR
MOUNTING
PLATE
SEALING
COVER
MAGNET
MAGNET
SPACER
5816OD-001-V0
The Honeywell 5816OD Wireless Outdoor Sensor (referred to as
the Sensor) brings the convenience of wireless technology to the
outdoors. The major features are:
 Weatherized security protection for an outdoor environment.
Great for sheds, barns, garages, pool gates, fences, and rural
mailbox (notifications).
 Versatile mounting options on flat and round materials.
 Cover and rear tamper detection.
 Can be painted to coordinate with mounting surface.
 Operating temp: – 40 to +50° C (– 40 to +122° F) at
RH of 100% (rain, snow).
 Maximum Magnet Gap:
Wood: 1.75 inches
Metal: 1.25 inches
Installing / Replacing the Batteries
IMPORTANT:
 Always change both batteries. Do not mix weak batteries with
new batteries.
 Use two (2) lithium 1.5VDC AA cells. (For best life, use
Eveready's Energizer Ultimate LITHIUM AA batteries,
Honeywell part number 462)
 OBSERVE BATTERY POLARITY.
TERMINAL BLOCK
FOR EXTERNAL
CONTACT SWITCH
PRY
POINTS
Battery Replacement:
1. Remove cover screw and swing Sensor to remove from Sensor
Mounting Plate.
2. Use screwdriver in any pivot point and pry Sealing Cover off.
Replace batteries.
3. Orient the Sealing Cover so the screw hole lines up with the
screw hole in the sensor cover, and press to close.
4. Engage Sensor tabs into mating holes in Sensor Mounting
Plate and swing closed. Secure with cover screw.
5816OD-002-V0
Mounting Guidelines
 This device is intended for vertical surfaces (to be mounted at a
sufficient height) where snow, ice and water buildup will not
interfere with its operation.
 Mount the Magnet on the magnet sensing side of the Sensor as
identified by the side ribs on the Sensor.
 Mount the Sensor on a stationary surface, and mount the
Magnet on the moveable surface.
 When used on wooden sheds and barns, mount the sensor and
magnet on the inside of the structure.
 Use the Magnet Spacer when mounting on metal surfaces; or
if needed to achieve proper alignment with the Sensor.
 Use screws suitable for the material being fastened to.
FLAT SURFACES
GATE
FENCE
MAGNET
SPACER
SENSOR
MOUNTING
PLATE
MAGNET
MOUNTING
SCREW (2)
SENSOR
COVER
SCREW
MOUNTING
SCREW (4)
5816OD-003-V0
Curved Surfaces:
Suggested mounting hardware such as the strap ties and cable
ties are not supplied.
 Mount using self locking stainless steel strap ties.
CURVED SURFACES
GATE
POST
FENCE
GATE
5816OD-005-V0
 Alternately you can use extra heavy duty Nylon 6/6 UV and
Temperature Rated cable ties
(0.5 inch wide).
COVER
SCREW
 If desired you may use screws in addition to the ties.
MAGNET
SPACER
SENSOR
MOUNTING
PLATE
ED
CO
MM
ON
OP
EN
UL – The wired contact must be less than 3 feet from the
transmitter.
1. Strip cable jacket back 4-inches to allow enough slack to
remove Sealing Cover when changing batteries.
2. Pass cable through the access hole in Sensor Mounting Plate.
Use cable notch on mounting plate to pass jacketed portion of
cable through. Then attach the Sensor Mounting Plate.
3. Route cable to the external contact switch and fasten at
intervals to secure cable.
4. Remove the Sealing Cover and thread wires through the
rubber wire seal. If installed, REMOVE ANY BATTERIES.
5. Connect wires to terminal block in battery chamber, then
INSTALL the batteries.
6. Replace the Sealing Cover. (Note, orient the cover so the screw
hole lines up with the screw hole in the sensor cover, and press
to close.)
7. Engage Sensor tabs into Sensor Mounting Plate mating holes
and swing closed. Secure with cover screw.
5816OD-004-V0
TO EXTERNAL
CONTACT SWITCH
CL
OS
ROUTING EXTERNAL WIRING – Optional for use with external
closed contact switches, such as the Honeywell N7945-2GY:
Note: Use minimum of 22AWG jacketed cable. The contact
switch must be a Form C (SPDT) type.
MAGNET
MAGNET
SENSING
SLIDE
SENSOR
CONNECT WIRES
TO TERMINAL BLOCK
IN BATTERY CHAMBER
SENSOR
PAINTING THE SENSOR:
The sensor and magnet may be painted to coordinate its color with the mounting surface. Use
only paints that are made for plastic and follow the manufacturer’s direction for preparing the
plastic and applying the paint. Observe the required drying and curing times.
DO NOT USE METALLIC PAINT COLORS.
SENSOR
MOUNTING
PLATE
SEALING
COVER
5816OD-006-V0
Self Locking Stainless Steel Strap Tie
Recommended Paints:
 Krylon® "Fusion for Plastic"
 Rust-Oleum® "Plastic"
 Dupli-Color® "Vinyl & Fabric Coating"
Programming the Control Panel
You must program the transmitter's serial number, input type (RF Supervised), response type, and loop # in the control panel. (Either or both
loops may be used. Loop # 2 is for the magnet sensing, and Loop # 1 is for the external contact switch.) Refer to the control panel’s instructions
for further details. Note: The transmitter's serial number may be found on the carton, and in the Battery Chamber.
FCC / IC STATEMENT
This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause
undesired operation.
Cet appareil est conforme à la partie 15 des règles de la FCC & de RSS 210 des Industries Canada. Son fonctionnement est soumis aux conditions
suivantes: (1) Cet appareil ne doit pas causer d' interferences nuisibles. (2) Cet appareil doit accepter toute interference reçue y compris les
interferences causant une reception indésirable.
FEDERAL COMMUNICATIONS COMMISSION STATEMENT
The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User’s Manual.
Unauthorized changes or modifications could void the user’s authority to operate the equipment.
Ê800-04494UŠ
800-04494 6/10 Rev. A
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
Copyright  2010 Honeywell International Inc.
www.honeywell.com/security

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Create Date                     : 2011:02:23 11:36:25-05:00
Creator Tool                    : Acrobat PDFMaker 9.1 for Word
Modify Date                     : 2011:03:01 11:04:06-05:00
Metadata Date                   : 2011:03:01 11:04:06-05:00
Producer                        : Acrobat Distiller 9.4.2 (Windows)
Keywords                        : 
Format                          : application/pdf
Creator                         : E365313
Title                           : 5816OD Wireless Outdoor Sensor
Description                     : Quick Installation Guide
Document ID                     : uuid:291da278-28d3-4558-b992-e540d8217088
Instance ID                     : uuid:c0555f0e-78b5-4ea2-9e81-ec60d39607ee
Company                         : Honeywell, Inc.
Comments                        : 
Page Layout                     : OneColumn
Page Count                      : 2
Author                          : E365313
Subject                         : Quick Installation Guide

EXIF Metadata provided by EXIF.tools