Ademco 8DL5869-1 Remote Security Transmitter User Manual K5299V1 ii

Download:
Mirror Download [FCC.gov]
Document ID	535891
Application ID	RimLoEks8aNZiS1cGQ6wvQ==
Document Description	users manual with FCC Part 15 Statment and FCC ID
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	12.02kB (150283 bits)
Date Submitted	2005-04-26 00:00:00
Date Available	2005-08-08 00:00:00
Creation Date	2005-04-23 19:49:18
Producing Software	Acrobat Distiller 6.0 (Windows)
Document Lastmod	2005-04-23 19:49:18
Document Title	Microsoft Word - K5299V1_ii.doc
Document Creator	PScript5.dll Version 5.2.2
Document Author:	E650365

K5299V1 3/03
5869
Holdup Switch/Transmitter
INSTALLATION AND SETUP GUIDE
GENERAL INFORMATION
MOUNTING
The 5869 Holdup Switch/Transmitter is a finger-operated
RF transmitting device used for activating a holdup signal
at the security system control, and/or any other security
application. The 5869 is typically mounted under a counter
or money draw for inconspicuous operation. When the
transmitter is activated, it sends an RF signal to the control
panel, which then sends a burglary alarm to the central
station.
Once the 5869 trigger (Figure 1) is activated, the supplied
reset key K4563 must be used to reset the device. The 5869
also contain tamper switches that are activated either when
the cover is removed, or when the unit is forcibly removed
from its installation location.
Mount the 5869 under a counter or money drawer for easy
access by the cashier. Refer to the figure and steps that
follow for typical mounting installation.
Before mounting the 5869 permanently, perform Go/No Go
tests to verify adequate transmitter signal strength at desired
mounting location (refer to the Security System Control
Panel Installation and Setup Guide).
1. Install the battery into the battery holder observing
correct polarity as shown in Figure 1.
2. Position the case to the desired location and install one
No. 6 x ¾ screw (supplied) at the breakaway tamper
release hole as shown in Figure 2 .
3. Secure the cover to the case with the two screws (No 6 x
1/2) as shown in Figure 2.
IMPORTANT: To prevent damage to the case, do not
over tighten the cover screws.
4. Secure the case with the cover to its mounting location
using the two screws (No. 6 x 2) supplied as shown in
Figure 2.
The 5869 has a permanent serial number assigned during
manufacture used for enrolling the 5869 with the security
system control panel. To enroll the 5869, refer to the
respective Security System Control Panel Installation and
Setup Guide.
RESET
KEY
PROGRAMMING
COVER
ATTACH
HOLE
MOUNTING
HOLE
(TYP.)
COVER
TRIGGER
COVER
SCREW (2)
No. 6X1/2
The 5869 Holdup Switch/Transmitter should be
programmed as a 24-hour silent zone type. Refer to the
Security System Control Panel Installation and Setup
Guide for programming instructions.
NOTES:
•
During programming of the control panel, the 5869
Holdup Switch/Transmitter should be treated as "RF"
(i.e., supervised RF) Type.
•
The 5869 is one closed input loop zone (loop 1).
BATTERY INSTALLATION/REPLACEMENT
3V
LITHIUM
BATTERY
BATTERY CAUTION:
Risk of fire, explosion, and burns. Do not recharge, disassemble, heat above 100°C, or incinerate. Dispose of used
batteries promptly and properly. Keep away from children.
BREAKAWAY
TAMPER
SCREW
No. 6X3/4
IMPORTANT: The case will be held in place by the
tamper release tab once the cover and mounting screws
are removed. Exercise caution not to jar the case while
replacing the battery, possibly breaking the Tamper
breakaway tab.
COVER
TAMPER
SWITCH
MOUNTING
SCREW (2)
No. 6X2
ANTENNA
1.
COVER
ATTACH
HOLE
Remove the screws securing the 5869 cover and case to
its mounting location.
NOTE: Use care not to bend the antenna while
attempting to remove or install the battery.
COVER
SCREW (2)
No. 6X1/2
5869-002-V1
2.
Remove faulty battery and dispose of properly.
3.
Observing correct polarity, insert the battery into the
battery holder as shown in Figure 2.
4.
Re-install screws to secure cover and case as shown in
Figure 2.
Figure 1. 5869 Holdup Switch/Transmitter Details
SPECIFICATIONS
Physical
1-15/16"W x 5-15/16"H x 1-3/16"D
(50mm x 150mm x 30mm)
Battery
3-volt Lithium. ADEMCO 466, Duracell
DL123A, Panasonic CR123A, Sanyo CR123A,
Varta CR123A, or equivalent.
Frequency
345MHz
Reset Key:
Supplied, Part Number K4563 to order
separately
Agency:
UL 636 – Holdup alarm units and systems
MOUNTING
HOLE
MOUNTING
HOLE
BREAKAWAY
TAMPER
SCREW
No. 6X3/4
COVER
SCREW (2)
No. 6x1/2
MOUNTING
SCREW (2)
No. 6X2
MOUNTING
SCREW (2)
No. 6X2
COVER
SCREW (2)
No. 6x1/2
IMPORTANT:
THIS DEVICE MUST BE PERMANENTLY
MOUNTED WITH THE SCREWS SUPPLIED.
HOLDUP SWITCH SHOWN MOUNTED
IN TYPICAL UNDER COUNTER APPLICATION.
US
LISTED
5869-004-V0
Figure 2. Typical Holdup Switch Installation
TO THE INSTALLER
Regular maintenance and inspection (at least annually) by the installer and frequent testing by the user are
vital to continuous satisfactory operation of any alarm system.
The installer should assume the responsibility of developing and offering a regular maintenance program to
the user, as well as acquainting the user with the proper operation and limitations of the alarm system and its
component parts. Recommendations must be included for a specific program of frequent testing (at least
weekly) to insure the system's operation at all times.
FCC ID: CFS8DL5869-1
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause
undesired operation.
CANADA: 573F-58691
LIMITED WARRANTY
Honeywell International Inc., acting through its Security & Custom Electronics business ("Seller") 165 Eileen Way, Syosset, New York 11791, warrants its
product(s) to be in conformance with its own plans and specifications and to be free from defects in materials and workmanship under normal use and
service for 24 months from the date stamp control on the product(s) or, for product(s) not having a manufacturer’s date stamp, for 12 months from date of
original purchase unless the installation instructions or catalog sets forth a shorter period, in which case the shorter period shall apply. Seller's obligation
shall be limited to repairing or replacing, at its option, free of charge for materials or labor, any product(s) which is proved not in compliance with Seller's
specifications or proves defective in materials or workmanship under normal use and service. Seller shall have no obligation under this Limited Warranty
or otherwise if the product(s) is altered or improperly repaired or serviced by anyone other than Honeywell factory service. For warranty service, return
product(s) transportation prepaid, to Honeywell Factory Service, 165 Eileen Way, Syosset, New York 11791.
THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, OF MERCHANTABILITY, OR FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE, WHICH
EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO CASE SHALL SELLER BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR
INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, OR UPON ANY OTHER BASIS OF LIABILITY
WHATSOEVER, EVEN IF THE LOSS OR DAMAGE IS CAUSED BY THE SELLER'S OWN NEGLIGENCE OR FAULT.
Seller does not represent that the product(s) it sells may not be compromised or circumvented; that the product(s) will prevent any personal injury or
property loss by burglary, robbery, fire or otherwise; or that the product(s) will in all cases provide adequate warning or protection. Customer understands
that a properly installed and maintained alarm system may only reduce the risk of a burglary, robbery, fire, or other events occurring without providing an
alarm, but it is not insurance or a guarantee that such will not occur or that there will be no personal injury or property loss as a result.
CONSEQUENTLY, SELLER SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY, PROPERTY DAMAGE OR OTHER LOSS BASED ON A
CLAIM THAT THE PRODUCT(S) FAILED TO GIVE WARNING. HOWEVER, IF SELLER IS HELD LIABLE, WHETHER DIRECTLY OR INDIRECTLY,
FOR ANY LOSS OR DAMAGE ARISING UNDER THIS LIMITED WARRANTY OR OTHERWISE, REGARDLESS OF CAUSE OR ORIGIN, SELLER'S
MAXIMUM LIABILITY SHALL NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT(S), WHICH SHALL BE THE COMPLETE
AND EXCLUSIVE REMEDY AGAINST SELLER.
This warranty replaces any previous warranties and is the only warranty made by Seller on this product(s). No increase or alteration, written or verbal, of
the obligations of this Limited Warranty is authorized.
165 Eileen Way, Syosset, New York 11791
Copyright © 2004 Honeywell International, Inc.
www.honeywell.com/security
ÊN6483V3nŠ

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 3
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:262e9fb5-6cba-467b-b09c-6ce71705dfc0
Producer                        : Acrobat Distiller 6.0 (Windows)
Create Date                     : 2005:04:23 19:49:18-04:00
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2005:04:23 19:49:18-04:00
Document ID                     : uuid:0127c480-174e-48b7-9e80-d4834761a917
Format                          : application/pdf
Title                           : Microsoft Word - K5299V1_ii.doc
Creator                         : E650365
Author                          : E650365

EXIF Metadata provided by EXIF.tools