Advance Security R42 Car Alarm Receiver User Manual 7920PINS qxp

Download:
Mirror Download [FCC.gov]
Document ID	517888
Application ID	VN+1mdKxP57SR3gSSj0eEQ==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	50.36kB (629481 bits)
Date Submitted	2005-02-23 00:00:00
Date Available	2005-02-23 00:00:00
Creation Date	2004-12-14 16:39:42
Producing Software	QuarkXPress(tm) 6.0
Document Lastmod	2005-02-14 15:42:50
Document Title	7920PINS.qxp
Document Creator	QuarkXPress(tm) 6.0

For Technical Assistance Call:
(800) 638-3600
I N S TA L L AT I O N I N S T R U C T I O N S
Model: 7921P
Step 1: 10-Pin Main Harness Installation
The main wire harness contains 8 wires which all have a specific purpose.
Follow the wiring recommendations enclosed for each wire. Wires not used
should be released from the harness connector or taped off to prevent accidental
shorting.
Gray Wire: The gray wire is a pulsed ground output designed to activate the
vehicle’s existing car horn system in place of or in addition to a siren
sounding device. Connect the gray wire to the negative trigger wire on the
vehicle’s horn relay.
Step 3: 5-Pin Power Harness Installation
The power harness contains 3 wires and two vacant sockets, this power harness
does not come packaged with the alarm module but in 5901H1, 5901H2,
5901H3 harness kits or custom starter disable/power interface harnesses.
Packaged with the 10-pin main harness are two loose wires (an Orange wire and
a White wire with a Black stripe). Follow the wiring recommendations enclosed
for each wire.
Power Harness
WARNING! Maximum output of this wire is 300mA. Horn systems requiring
positive voltage or more than 300mA to trigger the horn relay will require an
additional relay to increase current capabilities.
Blue Wire with White Stripe: This wire provides a single pulsed ground when
the 7921P is disarmed so that it will disarm a factory installed alarm system.
Note: Some factory alarms systems may require a double pulse signal to
disarm the factory alarm system. In this case, you will need to add Silencer
adapter model #5902DP to the blue wire with white stripe.
First Socket (-) Domelight control output
Second Socket (+) 12 volts for the relay
Orange Wire: Insert the orange wire into the first socket of the power harness.
The orange wire is the dome light supervision control output. Connect the
orange wire to the required control relay.
Brown Wire: The brown wire is the positive siren output wire. Connect the
brown wire from the harness to the brown wire on the siren supplied. Ground
the remaining black wire from the siren.
White Wire with Black Stripe: Insert the white/black wire into the third socket of
the power harness. (As shown) The white/black wire is the (-) Channel #2
output wire and should be connected to an existing (-) activated trunk
release switch or an additional relay will have to be added to control the
trunk release mechanism.
Blue Wire: The blue wire is a negative trigger input that can be used for existing
or newly installed grounding type hood/trunk/ hatch pin switches. The blue
wire can also be used as an input for additional ground output electronic
sensors.
Step 4:Door Lock/Unlock Socket (3- Pin Black Socket)
For remote controlled door lock/unlock operation, follow the wiring diagram
enclosed (page 2). The harness is an optional part not supplied with 7921P.
Order part # 5902 or 5903 for one-wire multiplexing door locking systems.
Green Wire: The green wire is the negative (-) door trigger input. If the vehicle
you are working on has a negative (-) triggered dome light system, connect
the green wire to the common dome light trigger wire. This wire is usually
located at the driver’s side door jamb switch.
Step 5: Auxiliary Interrupt Wiring (2-Pin Orange Socket)
To interrupt an additional circuit(s), all alarm modules require either the ALARPS, ALA-RPS2 or ALA-RPS3 relay pack. Follow the wiring instructions
supplied with the relay packs.
Violet Wire: The violet wire is the positive (+) door trigger input. If the vehicle
you are working on has a positive (+) triggered dome light system, connect
the violet wire to the common dome light trigger wire. This wire is usually
located at the driver’s side door jamb switch.
Step 6: Dip Switch Feature Programming
Dip Switch #1: Ignition Key Controlled Lock/Unlock (Door lock control function
must be connected and the door lock output feature must be “On” in the
dealer mode)
Note: This feature can be programmed using the #1 Dip Switch in both the
dealer and consumer modes.
Place Dip Switch #1 to the “On” position to activate this feature.
Place Dip Switch #1 in the “Off” position to deactivate this feature.
Red Wire with White Stripe: The red/white wire is the output of the parking light
relay. Connect the red/white wire to the parking light trigger wire coming from
the headlight switch. Do not connect the red/white wire to a dashboard
lighting wire. Connecting the red/white into dashboard lighting can damage
the dashboard lighting dimmer switch.
Pink Wire: The pink wire is the input wire to the parking light relay. The
connection of the pink wire determines the output polarity of the parking light
relay. If the parking light system you are connecting to is positive activation,
connect the pink wire to battery +12vdc. If the parking light system you are
connecting to is negative activation, connect the pink wire the the frame of
the vehicle.
Note: (Applies to All Models) The main 10 pin harness contains two vacant
sockets. These vacant sockets are for channel #2 output. All the alarm
modules require an 5912 for channel #2 operation. Follow the wiring
instructions supplied with 5912. If a 5912 relay is not available, a standard
Bosch 5 pin relay can be used.
Main Harness
Dip Switch #2: Current Sensing
Note: This feature can be programmed using the #2 Dip Switch in both the
dealer and consumer modes.
Place Dip Switch #2 to the “On” position to have the current sensing feature on.
Place Dip Switch #2 in the “Off” position to have the current sensing feature off.
Dip Switch #3: Door Entry Delay
Note: This feature can be pre-programmed in dealer mode using the #3 Dip
Switch. The feature will not be functional in the dealer mode but will become
functional when the unit is converted to customer mode.
Place the dip switch in the "On" position. During customer mode operation,
the (+) or (-) door input trigger wires will have a 20 second entry delay. This
is primarily used for Ford vehicles that have keyless entry and use a door
mounted keypad.
Place the dip switch in the "Off" position (Factory Default) and the 20 second
door entry delay will be off (Instant Activation).
Vacant Sockets
+12 Volts for Relay (when needed)
(-) Channel #2 Output
Step 7: Additional Menu Programming
The Silencer model 7921P control module offers additional menu programmable
features. Follow the dealer or consumer remote feature programming sheets to
adjust the 7921P features.
Step 2: Arm / Disarm Harness Wiring (3-Pin White Socket)
Follow wiring diagram enclosed for proper connection to the factory installed
power door locking system to arm and disarm the 7921P security system.
1111 West Victoria Street
Compton, CA 90220
www.magnadyne.com
Proposed
© 2005 Copyright Magnadyne Corp.
INSTALLATION INSTRUCTIONS
LED
(White 2-Pin
Socket)
Model: 7921P
Valet Switch
(Blue 2-Pin Socket)
Arm/Disarm Harness
(White 3-Pin Socket)
DIP Switches
Gray Wire Horn (-) Pulsed Output
Blue/White Wire (-) Signal Output to
Disarm Factory Alarm
7921P
Controller
Ignition Locking**
(Black 3-Pin Socket)
Programmable Key
(Green 2-Pin Socket)
Brown Wire
Positive (+) Output for
an Optional Electronic Siren
Auxiliary Interrupt
(Orange 2-Pin Socket***)
Blue Wire Negative Pin Trigger Input
Green Wire Negative Door Trigger Input
Violet Wire Positive Door Trigger Input
Shock Sensor
(White 4-Pin Socket****)
White/Black Wire Channel #2 Output
5-Pin Power
Harness*
Red/White Wire Parking Lights Relay Output
Red Wire (Lock)
Orange Wire ***** 2nd Unlock Output (requires
additional relay & special wiring).
Black Wire (Unlock)
Pink Wire Parking Lights Relay Input
Starter Disable
Socket*
Left Door
Lock/Unlock Switch
Green Wire
White Wire
Blue Wire
Supplied with 5901H1, 5901H2 or 5901H3 Harness Kits or
Custom Starter/Disable T-harness.
**
Supplied with 5902 Ignition Controlled Locking Kit.
***
Supplied with ALA-RPS, ALA-RPS2 or ALA-RPS3 relay packs.
Programmable Key Receptacle
for Changing to
Customer Mode
or
Putting Unit to Sleep Mode
**** For a Single-Zone Shock Sensor use ALA930.
For a Dual-Zone Shock Sensor use ALA95 or ALA90.
***** This wire supplies +12V power, if not used cut this wire
off at connector to prevent shorting.
A = Possible Connection Points for Green Wire
B = Connection Point for Blue Wire
C = Possible Connection Points for White Wire
Optional
5902 Harness
Left Door
Jamb
Lock
Right Door
Jamb
Lock
Factory Keyless
Module
(Typical)
Unlock
Unlock
Right Front
Pass. Door
Driver's Door
Lock (+)
Unlock (+)
Lock (+)
Unlock (+)
Inside Door
Unlock (+)
Right Rear
Pass. Door
Left Rear
Pass. Door
Lock (+)
Right Door
Lock/Unlock Switch
Inside Vehicle
Lock (+)
Unlock (+)
Inside Door
Proposed
© 2005 Copyright Magnadyne Corp.
Models: 7921P, 7920P, 7919P Rev. C
C O N S U M E R R E M OT E F E AT U R E P R O G R A M M I N G
NOTE: The alarm must be in “consumer mode” before you can program
consumer mode features. See additional instruction sheets on performing this
function. When the alarm is programmed to consumer mode, a specific group of
operating features are reset to their default settings. These default settings can be
changed by following the enclosed procedures and using the special 7910P
programming transmitter.
NOTE: In the event that the 7910P transmitter is unavailable, the programming
can also be performed by the consumer transmitter once all buttons have been
programmed into the control module memory. (See “Consumer Remote Feature
Programming from the Consumer's Transmitter.) To get into the “Consumer
Remote Feature Programming” mode follow the procedures below”.
Programmable Alarm Feature
Default Setting
(Consumer Transmitter Mode)
(Consumer Transmitter Mode)
Chirp Status Indicator
2A
*Mode “P”
Automatic Arming of Alarm “On”, Automatic Arming of Starter Disable “On”
2B
*Mode “S”
Automatic Arming of Alarm “Off”, Automatic Arming of Starter Disable “On”
Starter Disable will Arm 70 Seconds After Last Door is Closed
Chirps On
Remote Panic from Factory Keyless Entry Transmitter
On
Safety Illumination Sentinel System
Off
* During Dealer Remote Feature Programming either the ”P” or “S” mode was selected. In the Consumer Remote Feature Programming mode you cannot change the mode (either
“S” or “P”) that was selected in the Dealer Feature Programming. You can change the features of the mode that was selected in the Dealer Mode. (See Step 5 for more details.) To
change mode “S” or “P” operation you have to recode a dealer transmitter to the unit and change the operation in the “Dealer Remote Programmable Feature” Mode.
Step 1
Step 2
Step 3
Dealer Switch
(Red Button)
Disarm Security
System
Consumer Switch
(Black Button)
Momentary Switch
Push On / Off
Turn On Ignition
The LED will remain off.
The LED will be off and
the horn / siren will emit 2
chirps.
ON
OFF
Toggle Switch
Push Once = On
Push Again = Off
☛
ON
☛
Insert the Valet Switch
Step 4
Push the Valet Switch:
6 Times if Using a Red Button Switch
12 Times if Using a Black Button Switch
(Represents 6 Times On / Off)
The LED will be on solid and the horn / siren will emit 1 long
then 1 short chirp. You are now in the “Consumer Remote
Feature Programming” mode.
Step 5
5910P Programming Transmitter
Blue
Button
Black
Button
Step 6
Use the 5910P transmitter and the chart below to
change the features as required. Press and hold
the button that controls the function you want to
change and listen for the chirp confirmation. You
can repeatedly press the same colored button
and turn the same function on and off as many
times as required until the operation is correct.
After all functions have been re-programmed to
operate as required go to step 6.
Red
Button
Button Color
Function
Black
Chirp Status Indication
OFF
Turn Off the Ignition
The horn / siren will emit 1 short chirp and 1 long chirp. You are
now out of the “Consumer Remote Feature Programming”
mode.
Confirmation = Change Function
1 Beep =
Chirp Status Indication “On”
2 Beeps = Chirp Status Indication “Off”
2A
Blue
1 Beep =
Mode “P”
Note: The auto arm door locking feature has
a default setting of "off" in customer mode.
To turn on or off the auto arm door locking
feature in customer mode, repeat the steps
for the "Blue" button and hold the transmitter
button down for more than 3 seconds to get
a second confirmation chirp. For example: (1
chirp = 10 sec auto arm on, auto door lock
off.) (1 chirp + 1 chirp = 10 sec auto arm on,
auto door lock on.)
Automatic Arming of Alarm “On”, Automatic Arming of Starter Disable “On”
Both will arm 10 seconds after last door is closed or rearm 10 seconds after remote disarm.
2 Beeps = Automatic Arming of Alarm “On”, Automatic Arming of Starter Disable “On”
Both will arm 20 seconds after last door is closed or rearm 20 seconds after remote disarm.
3 Beeps = Automatic Arming of Alarm “On”, Automatic Arming of Starter Disable “On”
Both will arm 45 seconds after last door is closed or rearm 60 seconds after remote disarm.
4 Beeps = Automatic Arming of Alarm “Off”, Automatic Arming of Starter Disable “On”
The starter will disable 70 seconds after last door is closed.
5 Beeps = Automatic Arming of Alarm “Off”, Automatic Arming of Starter Disable “Off”
2B
Blue
Mode “S”
Automatic Arming of Alarm “On”, Automatic Arming of Starter Disable “On”
Both will arm 45 seconds after last door is closed.
2 Beeps = Automatic Arming of Alarm “Off”, Automatic Arming of Starter Disable “On”
The starter will disable 70 seconds after last door is closed.
Red
Remote Panic from Factory Keyless
Entry Transmitter
1 Beep = Panic “On”
2 Beeps = Panic “Off”
Black + Blue
Safety Illumination Sentinel System
1 Beep =
3 Beeps = Safety Illumination Sentinel System “On”
4 Beeps = Safety Illumination Sentinel System “Off
1111 West Victoria Street
Compton, CA 90220
www.magnadyne.com
Proposed
© 2005 Copyright Magnadyne Corp.
Consumer Remote Feature Programming (7921P, 7920P, 7919P Rev. C)
REMOTE FEATURE PROGRAMMING USING THE CONSUMER’S TRANSMITTER
ARM/DIS
AUX
ARM/DIS
AUX
LOCK
AUX
UNLOCK
AUX
UNLOCK
LOCK
UNLOCK
PANIC
AUX
AUX
ARM/DIS
LOCK
PANIC
Button
Function
Confirmation = Change Function
ARM/DIS or LOCK
Chirp Status Indication and Single/
Dual Unlock Outputs
1 Beep = Chirp Status Indication “On”
2 Beeps = Chirp Status Indication “ Off”
2A
AUX (2-Button) or
Mode “P”
1 Beep =
TRUNK (3-Button) or
UNLOCK
Note: The auto arm door locking feature has
a default setting of "off" in customer mode.
To turn on or off the auto arm door locking
feature in customer mode, repeat the steps
for the "Blue" button and hold the transmitter
button down for more than 3 seconds to get
a second confirmation chirp. For example: (1
chirp = 10 sec auto arm on, auto door lock
off.) (1 chirp + 1 chirp = 10 sec auto arm on,
auto door lock on.)
Automatic Arming of Alarm “On”, Automatic Arming of Starter Disable “On”
Both will arm 10 seconds after last door is closed or rearm 10 seconds after remote disarm.
2 Beeps = Automatic Arming of Alarm “On”, Automatic Arming of Starter Disable “On”
Both will arm 20 seconds after last door is closed or rearm 20 seconds after remote disarm.
3 Beeps = Automatic Arming of Alarm “On”, Automatic Arming of Starter Disable “On”
Both will arm 45 seconds after last door is closed or rearm 60 seconds after remote disarm.
4 Beeps = Automatic Arming of Alarm “Off”, Automatic Arming of Starter Disable “On”
The starter will disable 70 seconds after last door is closed.
5 Beeps = Automatic Arming of Alarm “Off”, Automatic Arming of Starter Disable “Off”
2B
AUX (2-Button) or
Mode “S”
1 Beep =
Automatic Arming of Alarm “On”, Automatic Arming of Starter Disable “On”
Both will arm 30 seconds after last door is closed.
2 Beeps = Automatic Arming of Alarm “Off”, Automatic Arming of Starter Disable “On”
The starter will disable 70 seconds after last door is closed.
UNLOCK
Red Button on
5910P Only
Remote Panic from Factory Keyless
Keyless Transmitter
1 Beep = Panic “On”
2 Beeps = Panic “Off”
ARM/DIS (2-Button)+
AUX (2 Button) or
Safety Illumination Sentinel System
3 Beeps = Safety Illumination Sentinel System “On”
4 Beeps = Safety Illumination Sentinel System “Off”
LOCK + UNLOCK
FEATURE PROGRAMMING USING THE CONTROL MODULE’S DIP SWITCHES
The Silencer model 7921P control module offers 3
programmable features. Follow the instructions enclosed to
program these features using the Dip switches in the control
module.
®
Dip Switch #1: Ignition Key Controlled Lock/Unlock (Door lock control function
must be connected and the door lock output feature must be “on” in the dealer
mode)
Note: This feature can be programmed using the #1 Dip switch in both the
dealer and consumer modes.
Place Dip switch #1 to the “On” position to activate this feature.
Place Dip switch #1 in the “Off” position to deactivate this feature.
Back View of Housing
Dip Switch #2: Current Sensing
Note: This feature can be programmed using the #2 Dip switch in both the
dealer and consumer modes.
ON
Dip Switches
Place Dip switch #2 to the “On” position to have the current sensing feature on.
Place Dip switch #2 in the “Off” position to have the current sensing feature off.
Difference Between if a Dip Switch in Off or On
#2 Dip
Switch in the
“Off”
Position
#2 Dip
Switch in the
“On”
Position
Dip Switch #3: Door Entry Delay (Applies to 7921P only)
Note: This feature can be pre-programmed in dealer mode using the #3 dip
switch. The feature will not be functional in the dealer mode but will become
functional when the unit is converted to customer mode.
Place Dip switch #3 in the "on" position. During customer mode operation, the
(+) or (-) door input trigger wires will have a 20 second entry delay. This is
primarily used for Ford vehicles that have keyless entry and use a door
mounted keypad.
Place Dip switch #3 in the "off" position (Factory default) and the 20 second
door entry delay will be off (Instant Activation).
1111 West Victoria Street
Compton, CA 90220
www.magnadyne.com
Proposed
© 2005 Copyright Magnadyne Corp.
Models: 7921P, 7920P, 7919P Rev. C
D E A L E R
R E M OT E
F E AT U R E
P R O G R A M M I N G
When the Silencer security system control module learns the
dealer transmitter operating code, a specific group of features
are automatically programmed to their default settings.
Enclosed, is a chart of the default settings for dealer transmitter
operation.
Programmable Feature
Single/Dual Unlock Pulses
Automatic Arm Door Locking (See Note 1)
On
Chirp Status Indicator (See Note 2)
On
These default setting can only be changed by following the
enclosed procedures and using the special 5910P programming
transmitter (Shown Below).
Consumer Remote Feature Programming Modes for Automatic
Mode “P”
Arming of Alarm and Automatic Arming of Starter Disable.
( See Step 5 and Note 3 for Full Details)
Note: Pre-programming the “P and S” type auto arming modes is for use when the system is
put into consumer mode only. In dealer mode, auto arming is on without On/Off programming
and auto arm locking is on but can be programmed off as explained below.
®
To get into the “Dealer Remote Feature Programming” mode
repeat the following procedures:
Step 1
Step 2
Insert the Valet Switch
Consumer Switch
(Red Button)
(Black Button)
Single
Step 3
☛
Dealer Switch
Default Setting
Step 4
Disarm Security
System
Turn On Ignition
The LED will be off and
the horn/ siren will emit 2
short beeps.
ON
OFF
Momentary Switch
Toggle Switch
Push On/Off
Push it On then
Push it again for Off
☛
ON
Push the Valet Switch:
4 Times if Using a Red Button Switch
8 Times if Using a Black Button Switch
(Represents 4 Times On / Off)
The LED will be on solid. The horn/ siren will emit 1 long
then 1 short beep) You are now in the “Dealer Remote
Feature Programming” mode.
Step 5
5910P Programming Transmitter
Black
Button
Blue
Button
Step 6
Use the 5910P transmitter and the chart below to adjust the features as
required. Press the button that controls the function you want to change and
listen for the chirp confirmation. You can repeatedly press the same colored
button and turn the same function on and off as many times as required until the
operation is correct. After all functions have been re-programmed to operate as
required go to step 6.
OFF
Red
Button
Button Color
Black
Changed Function
Single or Dual Unlock Outputs
Confirmation
Blue
Dealer Mode Auto Arm Door Locking
Pre-Programmed Consumer Mode Auto Arm
Red
** Black + Blue
Chirp Status Indicator On/Off
Selects “P” or “S” Mode Operation
** Note: The Black +Blue Buttons Change Automatic Alarm
Arming of Alarm and Automatic Arming of Starter Disable in
the Consumer Mode Only!
Default Dealer Mode Operation is Always: Automatic Arming of
Alarm “On”, Automatic Arming of Starter Disable “On” and
Automatic Door Locking “On”.
Note 1: When transmitter operation is changed from a
dealer transmitter to a consumer transmitter the
automatic arm locking feature will default to
“OFF”. This feature can be programmed on in the
customer mode by following the consumer feature
programming chart.
1 Beep = Single Unlock Pulse
2 Beeps = Dual Unlock Pulses
1 Beep = Automatic Arm Door Locking On, Consumer Auto Arm is ON
2 Beeps = Automatic Arm Door Locking OFF, Consumer Auto Arm is ON
3 Beeps = Automatic Arm Door Locking On, Consumer Auto Arm is OFF
4 Beeps = Automatic Arm Door Locking OFF, Consumer Auto Arm is OFF
1 Beep = On, 2 Beeps = Off
4 Beeps = Mode “P” (See 2A Consumer Programming)
Automatic Arming of Alarm is “Programmable”
and Automatic Arming of Starter Disable is
“Programmable” in Consumer Mode Only.
3 Beeps = Mode “S” (See 2B Consumer Programming)
Automatic Arming of Alarm is “Programmable”
in Consumer Mode. Automatic Arming of
Starter Disable is Always “On” and is
“Not Programmable” in Dealer or Consumer Mode.
Note 2: When transmitter operation
is changed from a dealer
transmitter to a consumer
transmitter the horn/siren
and chirp indicator will return
to an “on” condition.
1111 West Victoria Street
Compton, CA 90220
www.magnadyne.com
Turn Off the Ignition
The LED will be off and the
horn / siren will emit 1 short
beep and 1 long beep. You are
now out of the feature
programming mode.
Note 3: When transmitter operation is changed from a
dealer transmitter to a consumer transmitter, the
automatic arming of alarm and automatic arming
of starter disable (Mode “S” or “P”) will remain as
programmed in the dealer transmitter mode. In
order to change Mode “S” or Mode “P” operation,
you have to re-code a dealer transmitter to the
unit and change the operation in the dealer
remote programmable feature mode.
Proposed
© 2005 Copyright Magnadyne Corp.
Models: 7921P, 7909P, 7905P
6900P, 6900P-2, 6905P, 6909P
WA K I N G
Step 1
U P
U N I T
F R O M
T H E
Step 2
Step 3
ON
Insert the Valet Switch
Dealer Switch
Consumer Switch
(Red Button)
(Black Button)
“ S L E E P
Turn On Ignition
☛
Push the Valet Switch
3 Times for Red Button
6 Times for Black Button
(Represents 3 Times On/Off)
ON
OFF
Momentary Switch
(Push On/Off)
A. Long horn chirp indicates the unit
is in code learning mode.
Toggle Switch
(Push On then
push it again for off)
Step 5
OR
Remove the Dealer or
Customer Key
M O D E ”
Step 4
OR
Insert a Dealer or
Customer Key
A. Horn chirps once to indicates the
code has been learned.
B. LED starts flashing slowly to
indicate the code has been
learned.
B. LED comes on indicating the unit is
in code learning mode.
Step 6
OFF
Turn Off Ignition
A. Horn chirps 1 short then 1 long to
indicates you have exited code
learning.
B. LED starts flashing slowly.
1111 West Victoria Street
Compton, CA 90220
www.magnadyne.com
Proposed
© 2005 Copyright Magnadyne Corp.
Models: 7921P, 7909P, 7905P
6900P, 6900P-2, 6905P, 6909P
P R O G R A M M I N G
T H E
U N I T
TO
“ S L E E P
M O D E ”
In the event the customer declines to purchase the Silencer security system and the system is not going to be removed
from the vehicle, it must be put into “Sleep” mode to prevent automatic arming.
The white sleep key can also be used to delete a dealer code and to reset the security system to it’s original state as it
was received from the factory.
Note: The system must be in dealer mode to use the white key. If the system is armed, you should disarm it with the
dealer key to prevent triggering.
Step 1
Step 2
Step 3
ON
Insert the Valet Switch
Dealer Switch
Consumer Switch
(Red Button)
(Black Button)
Turn On Ignition
Insert the White “Sleep”
Key into the Receptacle
Step 4
☛
Push the Valet Switch
6 Times for Red Button
12 Times for Black Button
(Represents 6 Times On/Off)
ON
OFF
A. The LED will flash 6 times.
Momentary Switch
(Push On/Off)
B. 6900P, 6900P-2 or 6905P: If the
5911 buzzer is installed, it will emit
6 beeps.
Toggle Switch
(Push On then
push it again for off)
Step 5
6909P: The horn/siren will emit 6
beeps. Also the parking lights will
flash 6 times.
Step 6
OFF
Remove the White “Sleep”
Key
Turn Off Ignition
A. The LED will be off. You are now
in the “Sleep” mode.
1111 West Victoria Street
Compton, CA 90220
www.magnadyne.com
Proposed
© 2005 Copyright Magnadyne Corp.
Models: 7921P, 7909P, 7905P
6900P, 6900P-2, 6905P, 6909P
DELETING THE DEALER OR CONSUMER KEY
Upon the customer purchasing the 6905P or 6909P, it will arm/disarm from the factory keyless remotes. He/she also
has the option of purchasing a customer key pack (5900PKP) to disarm the security system.
In the event the customer declines to purchase the customer Key Pack (5900PKP) the dealer key code “must” be
deleted. This is done by programming in the bright orange “dealer delete key”.
If the customer declines to purchase the customer key pack for the 6909P, but still wants the unit to automatically arm;
see 6909P Feature Programming to activate this feature.
Step 1
Step 2
Step 3
Step 4
OR
ON
Disarm the Security
System
Turn On Ignition
Insert the Valet Switch
Dealer Switch
Consumer Switch
(Red Button)
(Black Button)
Insert the Orange
“Delete Code” Key into
the Receptacle
ON
OFF
Momentary Switch
(Push on/off)
Step 5
Toggle Switch
(Push on then
push it again for off)
Step 7
Step 6
OF F
☛
Push the Valet Switch
6 Times for Red Button
12 Times for Black Button
Remove the Orange “Delete
Code” Key
(Represents 6 Times On/Off)
Turn Off Ignition
A. The LED will be off. (6905P and
6909P) You have now deleted all
key codes.
B. The horn/siren/chirper will emit 1
short and 1 long chirp.
A. The LED will flash 6 times. (6905P
and 6909P)
Note: When dealer or consumer key
code is deleted the security system
will be in the consumer mode..
B. 6905P: If the 5911 buzzer is
installed, it will emit 6 beeps.
6909P: The horn/siren will emit 6
beeps. Also the parking lights will
flash 6 times.
1111 West Victoria Street
Compton, CA 90220
www.magnadyne.com
Proposed
© 2005 Copyright Magnadyne Corp.
Models: 7921P, 7909P, 7905P
6900P, 6900P-2, 6905P, 6909P
C O N S U M E R
Step 1
K E Y
Step 2
Step 3
**
OR
C O D I N G
Step 4
OR
ON
Insert the Valet Switch
Dealer Switch
Consumer Switch
(Red Button)
(Black Button)
ON
OFF
Momentary Switch
(Push On/Off)
Insert the Dealer Key
Remove the Dealer Key
Turn On Ignition
Step 7
Step 8
* Model: 5910K
** Model: 5900-DB (Blue Key)
5900-DG (Green Key)
5900-DR (Red Key)
5900-DY (Yellow Key)
Toggle Switch
(Push On then
push it again for off)
Step 5
Step 6
OF F
☛
Push the Valet Switch
3 Times for Red Button
6 Times for Black Button
(Represents 3 Times On/Off)
A. Long horn chirp indicates the unit is in
code learning mode.
☛
***
Insert the Customer Key
Remove the Customer Key
A. Another short horn chirp indicates
the key code was learned.
Note: The system will automatically
exit code learning if a key is not
inserted within 15 seconds.
Turn Off Ignition
A. A short and long horn chirp
indicates you have exited code
learning.
*** Model: 5900PKP
Note: The dealer key will be erased when programmed to the customer key.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions.
1)•This device may not cause harmful interference, and
2)•This device must accept any interference received, including interference that may cause undesired operation.
Per FCC 15.21, you are cautioned that changes or modifications not expressly approved by the part responsible for compliance
could void the user’s authority to operate the equipment.
1111 West Victoria Street
Compton, CA 90220
www.magnadyne.com
Proposed
© 2005 Copyright Magnadyne Corp.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Creator                         : QuarkXPress(tm) 6.0
X Press Private                 : %%DocumentProcessColors: Cyan Black.%%MarksAllSeparations: true.%%EndComments
Create Date                     : 2004:12:14 16:39:42Z
Modify Date                     : 2005:02:14 15:42:50+08:00
Page Count                      : 9
Creation Date                   : 2004:12:14 16:39:42Z
Producer                        : QuarkXPress(tm) 6.0
Mod Date                        : 2005:02:14 15:42:50+08:00
Metadata Date                   : 2005:02:14 15:42:50+08:00
Title                           : 7920PINS.qxp
Has XFA                         : No

EXIF Metadata provided by EXIF.tools