Advance Security R44 Car Alarm Receiver User Manual

Advance Security Inc Car Alarm Receiver

Users Manual

APRIL/18/2004 1 MKE - 400 14 PIN PLUG: 7. Black / White Wire: (-) 200mA Channel 3 Output 8. Yellow Wire: To Ignition Switched +12V 9. Red Wire: To Vehicle’s +12V Constant Power 2. White / Black Wire: (+) 10A Porch Light Relay Output 12. Green Wire: (+) 200mA Vehicle’s Door Lock Output 13. Blue / White Wire: (+) 200mA Cargo’s Door Unlock Output 11. Green / White Wire: (+) 200mA Vehicle’s Door Unlock Output 3. Brown Wire: (+) 10A Dome Light Relay Output 5. Violet Wire: (+) 200mA Channel 5 Output 6. Orange Wire: (-) 200mA Channel 4 Output 14. Blue Wire: (+) 200mA Cargo’s Door Lock Output 4. White Wire: (+) 10A Parking Light Relay Output 10. Red / White Wire: To RV’s +12V Constant Power 1. Black Wire: Ground to Vehicle Frame.
APRIL/18/2004 2PROGRAMMING A. 3- BUTTON TRANSMITTER PROGRAMMING: Note: This mode will only retain the last 4 remote transmitters programmed. If the transmitter memory is exceeded, the security system will start deleting transmitters from memory in chronological order. 1. Turn the Ignition 'switch to ‘ON’ position. Within 15 seconds. 2. Push the Program switch 3 times, the on board LED will flashing and the beeper will emit a long chirp to indicate the system in the Transmitter programming mode. 3. Press and hold any button of the transmitter until the on board LED turns On for 2 seconds and the beeper responds with a confirming chirp, indicating the signal has been stored into memory. 4. If you have additional transmitters (up to 4) that need to be programmed, repeat step 3 for each transmitter. Exit: Turn Ignition to 'OFF' position, or leave it for 15 seconds. The on board LED turns Off and the beeper will emit 3 long chirps to confirm exit. B. 4- BUTTON TRANSMITTERS PROGRAMMING: Note: This mode will only retain the last 4 remote transmitters programmed. If the transmitter memory is exceeded, the security system will start deleting transmitters from memory in chronological order. 1. Turn the Ignition 'switch to ‘ON’ position. Within 15 seconds. 2. Push the Program switch 5 times, the on board LED will flashing and the beeper will emit a long chirp to indicate the system in the Transmitter programming mode. 3. Press and hold any button of the transmitter until the on board LED turns On for 2 seconds and the beeper responds with a confirming chirp, indicating the signal has been stored into memory. 4. If you have additional transmitters (up to 4) that need to be programmed, repeat step 3 for each transmitter. Exit: Turn Ignition to 'OFF' position, or leave it for 15 seconds. The on board LED turns Off and the beeper will emit 3 long chirps to confirm exit. C. FEATURES PROGRAMMING: 1. Turn the Ignition 'switch to ‘OFF’ position. Within 15 seconds. 2. Push the Program switch 7 times, the on board LED wills Turns On constantly and the beeper will emit a long chirp to indicate the system in the Feature programming mode. 3. Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to change. - The beeps from beeper and the on board LED pause will indicate previously setting. 4. Depress the transmitter button ‘A’ again to change the feature again. Simple keep re-depressing the transmitter button ‘A’ again until the module advances to your desired setting. 5. Depress the transmitter button ‘B’ corresponding to the feature ‘B’ you wants to program. Press Transmitter Button or keypad One Beep / LED one pause Factory Default Setting Two Beeps / LED Two pauses Press Button on the transmitter or Press and hold the “1/2” Key on the keypad for 3 seconds Channel 3 Output = Momentary output Channel 3 Output = Latched output Press Button on the transmitter or Press and hold the “3/4” Key on the keypad for 3 seconds Channel 4 Output = Momentary output Channel 4 Output = Latched output Press Button on the 3 button transmitter or Press Button on the 4 button transmitter or Press and hold the “5/6” Key on the keypad for 3 seconds Channel 5 Output = Momentary output Channel 5 Output = Latched output Exit: Turn Ignition to 'ON' position or Press the “LOCK” button 1 seconds on the key pad or leave it for 15 seconds. The beeper will emit 3 long chirps and the on board led will turns Off to confirm exit.
APRIL/18/2004 3D. ALL CODES BACK TO DEFAULT: 1 Enter the “MAGNADYNE Master Code” (7352000) on the keypad; the beeper will emit a long chirp to confirm the correct code was entered. 2 Press the “LOCK” key on the keypad and holding in for 5 seconds until five beeps is hearing then release the “LOCK” key 3 The system will re-program all codes back to default. (Default dealer code is 12345 and user code is 54321) E. RE-PROGRAM THE DEALER CODE: Default Dealer Code is 12345 1. Enter the “Dealer Code” on the keypad; the beeper will emit a long chirp to confirm the correct code was entered. 2. Press the “LOCK” key on the keypad and holding in for 2 seconds until five beeps is hearing then release the “LOCK” key. 3. Enter the new 4 – 6 digit dealer codes on the keypad. (The dealer code can be 4, 5 or 6 digits.) 4. Finish by press the “LOCK” key on the keypad one long beep with 2 short beeps to confirm the new dealer code has been stored into memory and the all user code was back to default setting (Default user code is 54321). Exit: If 15 seconds of inactivity expire during of above steps, the unit will revert back to the last successfully stored code. 3 long beep to confirm exit. F. PROGRAM THE USER CODE: Default Dealer Code is 54321 Note: This mode will only retain the last 4 “user code” programmed. If the “user code” memory is exceeded, the system will start deleting “user code” from memory in chronological order. 1. Enter the “Dealer Code” on the keypad; the beeper will emit a long chirp to confirm the correct code was entered. 2. Enter the new 4 – 6 digit user codes on the keypad. (The user code can be 4, 5 or 6 digits.) 3. Finish by press the “LOCK” key on the keypad one long beep with 2 short beeps to confirm the new dealer code has been stored into memory. 4. If you have additional user code (up to 4) that needs to be programmed, repeat step 2 and 3 for each new user code. Exit: Press and hold the “LOCK” key for 1 seconds or If 15 seconds of inactivity expire during of above steps, the unit will revert back to the last successfully stored code. 3 long beep to confirm exit. OPERATION: A. 4-BUTTON TRANSMITTER OPERATION: Transmitter Button System Function Remark Lock The Vehicle’s Doors and Cargo Door Parking light one flash. Unlock The Vehicle’s Doors 1. Parking light two flashes. 2. Dome light turns on for 30 seconds 3. Porch light turns on for 30 seconds Lock The Cargo Door Unlock The Cargo Door + Turns On the Porch Light for 30 seconds or Turns it Off Upon Vehicle’s Door Unlock B. 3-BUTTON TRANSMITTER OPERATION: Transmitter Button System Function Remark Lock The Vehicle’s Doors and Cargo Door Parking light one flash. Unlock The Vehicle’s Doors 1. Parking light two flashes. 2. Dome light turns on for 30 seconds 3. Porch light turns on for 30 seconds Turns On the Porch Light for 30 seconds or Turns it Off Upon Vehicle’s Door Unlock
APRIL/18/2004 4C. KEYPAD OPERATION: KEYPAD System Function Remark Press “LOCK” key. Lock The Vehicle’s Doors and Cargo Door Parking light one flash. Key in the “User Code“. Unlock The Vehicle’s Doors 1. Parking light two flashes. 2. Dome light turns on for 30 seconds 3. Porch light turns on for 30 seconds Press and hold “1/2“ key for 3 seconds Lock or Unlock The Cargo Door Upon Vehicle’s Door Unlock Press and hold “3/4“ key for 3 seconds Turns On the Porch Light for 30 seconds or Turns it Off Upon Vehicle’s Door Unlock Key in the “User Code“ first then press “5/6“ key within 5 seconds Activate the Channel 3 output Key in the “User Code“ first then press “7/8“ key within 5 seconds Activate the Channel 4 output Key in the “User Code“ first then press “9/0“ key within 5 seconds Activate the Channel 5 output Note: Turn On the ignition switch or “lock” the vehicle’s door will turn off the dome light. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions. 1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that may cause undesired operation. Per FCC 15.21, you are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment.

Navigation menu