Advance Security R44 Car Alarm Receiver User Manual

Download:
Mirror Download [FCC.gov]
Document ID	502682
Application ID	4LUkWCyI1FxrzARxZANvGg==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	2.28kB (28473 bits)
Date Submitted	2004-12-31 00:00:00
Date Available	2004-12-31 00:00:00
Creation Date	2004-12-23 16:26:03
Producing Software	Acrobat Distiller 6.0 (Windows)
Document Lastmod	2004-12-23 16:36:31
Document Title	untitled

APRIL/18/2004
MKE - 400
14 PIN PLUG:
14. Blue Wire: (+) 200mA Cargo’s Door Lock Output
13. Blue / White Wire: (+) 200mA Cargo’s Door Unlock Output
12. Green Wire: (+) 200mA Vehicle’s Door Lock Output
11. Green / White Wire: (+) 200mA Vehicle’s Door Unlock Output
10. Red / White Wire: To RV’s +12V Constant Power
9. Red Wire: To Vehicle’s +12V Constant Power
8. Yellow Wire: To Ignition Switched +12V
7. Black / White Wire: (-) 200mA Channel 3 Output
6. Orange Wire: (-) 200mA Channel 4 Output
5. Violet Wire: (+) 200mA Channel 5 Output
4. White Wire: (+) 10A Parking Light Relay Output
3. Brown Wire: (+) 10A Dome Light Relay Output
2. White / Black Wire: (+) 10A Porch Light Relay Output
1. Black Wire: Ground to Vehicle Frame.
APRIL/18/2004
PROGRAMMING
A. 3- BUTTON TRANSMITTER PROGRAMMING:
Note: This mode will only retain the last 4 remote transmitters programmed. If the transmitter memory is
exceeded, the security system will start deleting transmitters from memory in chronological order.
1. Turn the Ignition 'switch to ‘ON’ position. Within 15 seconds.
2. Push the Program switch 3 times, the on board LED will flashing and the beeper will emit a long chirp to
indicate the system in the Transmitter programming mode.
3. Press and hold any button of the transmitter until the on board LED turns On for 2 seconds and the
beeper responds with a confirming chirp, indicating the signal has been stored into memory.
4. If you have additional transmitters (up to 4) that need to be programmed, repeat step 3 for each
transmitter.
Exit: Turn Ignition to 'OFF' position, or leave it for 15 seconds. The on board LED turns Off and the beeper
will emit 3 long chirps to confirm exit.
B. 4- BUTTON TRANSMITTERS PROGRAMMING:
Note: This mode will only retain the last 4 remote transmitters programmed. If the transmitter memory is
exceeded, the security system will start deleting transmitters from memory in chronological order.
1. Turn the Ignition 'switch to ‘ON’ position. Within 15 seconds.
2. Push the Program switch 5 times, the on board LED will flashing and the beeper will emit a long chirp to
indicate the system in the Transmitter programming mode.
3. Press and hold any button of the transmitter until the on board LED turns On for 2 seconds and the
beeper responds with a confirming chirp, indicating the signal has been stored into memory.
4. If you have additional transmitters (up to 4) that need to be programmed, repeat step 3 for each
transmitter.
Exit: Turn Ignition to 'OFF' position, or leave it for 15 seconds. The on board LED turns Off and the beeper
will emit 3 long chirps to confirm exit.
C. FEATURES PROGRAMMING:
1. Turn the Ignition 'switch to ‘OFF’ position. Within 15 seconds.
2. Push the Program switch 7 times, the on board LED wills Turns On constantly and the beeper will emit a
long chirp to indicate the system in the Feature programming mode.
3. Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to change.
- The beeps from beeper and the on board LED pause will indicate previously setting.
4. Depress the transmitter button ‘A’ again to change the feature again. Simple keep re-depressing the
transmitter button ‘A’ again until the module advances to your desired setting.
5. Depress the transmitter button ‘B’ corresponding to the feature ‘B’ you wants to program.
Press Transmitter Button or
One Beep / LED one pause
Two Beeps / LED Two pauses
keypad
Factory Default Setting
Channel 3 Output = Momentary
Channel 3 Output = Latched
Press
Button on the
output
output
transmitter or
Press and hold the “1/2” Key on
the keypad for 3 seconds
Press
Button on the
transmitter or
Press and hold the “3/4” Key on
the keypad for 3 seconds
Channel 4 Output = Momentary
output
Channel 4 Output = Latched
output
Press
Channel 5 Output = Momentary
Channel 5 Output = Latched
output
output
Button on the 3
button transmitter or
Press
Button on the 4
button transmitter or
Press and hold the “5/6” Key on
the keypad for 3 seconds
Exit: Turn Ignition to 'ON' position or Press the “LOCK” button 1 seconds on the key pad or leave it for 15
seconds. The beeper will emit 3 long chirps and the on board led will turns Off to confirm exit.
APRIL/18/2004
D. ALL CODES BACK TO DEFAULT:
Enter the “MAGNADYNE Master Code” (7352000) on the keypad; the beeper will emit a long chirp to
confirm the correct code was entered.
Press the “LOCK” key on the keypad and holding in for 5 seconds until five beeps is hearing then
release the “LOCK” key
The system will re-program all codes back to default. (Default dealer code is 12345 and user code is
54321)
E. RE-PROGRAM THE DEALER CODE: Default Dealer Code is 12345
1. Enter the “Dealer Code” on the keypad; the beeper will emit a long chirp to confirm the correct code was
entered.
2. Press the “LOCK” key on the keypad and holding in for 2 seconds until five beeps is hearing then release
the “LOCK” key.
3. Enter the new 4 – 6 digit dealer codes on the keypad. (The dealer code can be 4, 5 or 6 digits.)
4. Finish by press the “LOCK” key on the keypad one long beep with 2 short beeps to confirm the new
dealer code has been stored into memory and the all user code was back to default setting (Default user
code is 54321).
Exit: If 15 seconds of inactivity expire during of above steps, the unit will revert back to the last successfully
stored code. 3 long beep to confirm exit.
F. PROGRAM THE USER CODE: Default Dealer Code is 54321
Note: This mode will only retain the last 4 “user code” programmed. If the “user code” memory is exceeded,
the system will start deleting “user code” from memory in chronological order.
1. Enter the “Dealer Code” on the keypad; the beeper will emit a long chirp to confirm the correct code was
entered.
2. Enter the new 4 – 6 digit user codes on the keypad. (The user code can be 4, 5 or 6 digits.)
3. Finish by press the “LOCK” key on the keypad one long beep with 2 short beeps to confirm the new
dealer code has been stored into memory.
4. If you have additional user code (up to 4) that needs to be programmed, repeat step 2 and 3 for each new
user code.
Exit: Press and hold the “LOCK” key for 1 seconds or If 15 seconds of inactivity expire during of above
steps, the unit will revert back to the last successfully stored code. 3 long beep to confirm exit.
OPERATION:
A. 4-BUTTON TRANSMITTER OPERATION:
Transmitter Button
System Function
Lock The Vehicle’s Doors and
Cargo Door
Unlock The Vehicle’s Doors
Remark
Parking light one flash.
1. Parking light two flashes.
2. Dome light turns on for 30 seconds
3. Porch light turns on for 30 seconds
Lock The Cargo Door
Unlock The Cargo Door
Turns On the Porch Light for 30
seconds or Turns it Off
Upon Vehicle’s Door Unlock
B. 3-BUTTON TRANSMITTER OPERATION:
Transmitter Button
System Function
Lock The Vehicle’s Doors and
Cargo Door
Unlock The Vehicle’s Doors
Turns On the Porch Light for 30
seconds or Turns it Off
Remark
Parking light one flash.
1. Parking light two flashes.
2. Dome light turns on for 30 seconds
3. Porch light turns on for 30 seconds
Upon Vehicle’s Door Unlock
APRIL/18/2004
C. KEYPAD OPERATION:
KEYPAD
Press “LOCK” key.
Key in the “User Code“.
System Function
Lock The Vehicle’s Doors and
Cargo Door
Unlock The Vehicle’s Doors
Remark
Parking light one flash.
1. Parking light two flashes.
2. Dome light turns on for 30 seconds
3. Porch light turns on for 30 seconds
Upon Vehicle’s Door Unlock
Press and hold “1/2“ key Lock or Unlock The Cargo Door
for 3 seconds
Press and hold “3/4“ key Turns On the Porch Light for 30 Upon Vehicle’s Door Unlock
seconds or Turns it Off
for 3 seconds
Activate the Channel 3 output
Key in the “User Code“
first then press “5/6“ key
within 5 seconds
Activate the Channel 4 output
Key in the “User Code“
first then press “7/8“ key
within 5 seconds
Activate the Channel 5 output
Key in the “User Code“
first then press “9/0“ key
within 5 seconds
Note: Turn On the ignition switch or “lock” the vehicle’s door will turn off the dome light.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions.
1) This device may not cause harmful interference, and
2) This device must accept any interference received, including interference that may cause undesired
operation.
Per FCC 15.21, you are cautioned that changes or modifications not expressly approved by the part
responsible for compliance could void the user’s authority to operate the equipment.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 4
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:f5002efb-e0a7-4d3a-ae5e-2e5345f46c5f
Producer                        : Acrobat Distiller 6.0 (Windows)
Create Date                     : 2004:12:23 16:26:03+08:00
Modify Date                     : 2004:12:23 16:36:31+08:00
Metadata Date                   : 2004:12:23 16:36:31+08:00
Document ID                     : uuid:a0d5ace7-3cda-49ff-bd12-b9a7b757f0f4
Format                          : application/pdf
Title                           : untitled

EXIF Metadata provided by EXIF.tools