Advance Security R52 Car Alarm Receiver User Manual DELETE

Advance Security Inc Car Alarm Receiver DELETE

Contents

User manual 1 of 2

1
PRO PLM Installation Instructions
Avoid mounting components or routing wires near
hot surfaces
Avoid mounting components or routing wires near
moving parts
Tape or loom wires under hood for protection and
appearance
Use grommets when routing wires through metal
surfaces
Use a Digital Multi Meter for testing and verifying
circuits. DO NOT USE A TEST LIGHT, OR
"COMPUTER SAFE PROBE" as these can set off air
bags or damage vehicle computers.
PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED
Installation Precautions:
Roll down window to avoid locking keys in vehicle
during installation
FCC COMPLIANCE
This device complies with Part 15 of the FCC rules and with RSS-210 of Industry Canada.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including any interference that may
cause undesired operation.
Warning! Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Technical Support (800) 225-6074
or go to
http://techservices.audiovox.com
2
PRO PLM SYSTEM LAYOUT
BLACK GROUND
YELLOW IGNITION
PURPLE DOOR TRIGGER (+)
RED/WHITE +12 VOLT BATTERY
WHITE PARKING LIGHT OUTPUT
BROWN DOOR TRIGGER (-)
RED PARKING LIGHT INPUT
ORANGE ARMED OUTPUT (-)
OPEN
DK GREEN INSTANT TRIGGER (-)
BLACK/WHITE HORN OUTPUT (-)
LT. GREEN INSTANT TRIGGER (-)
GREEN/WHITE ILLUMINATED ENTRY (-)
DK BLUE TRUNK RELEASE (-)
BLUE TRUNK SHUNT (+)
RED/BLACK DISARM INPUT 2
RED DISARM INPUT
GREEN/BLACK ARM INPUT 2
GREEN ARM INPUT
RED/BLACK 2ND UNLOCK
GREEN UNLOCK OUPUT (-)
RED LOCK OUTPUT (-)
TRACKING PORT
PROGRAMMING BUTTON
LED / OVERRIDE BUTTON
3 Pin 5 Pin 6 Pin 8 Pin
DBI PORT
SHOCK SENSOR DIAL
PROPLM
3
SETUP & PROGRAMMING - CONSUMER MODE
Consumer Mode Transmitter Programming Bank
1. Turn the ignition ON.
2. Press and release the override button 3 times.
3. The system will chirp 1 time.
4. Press the lock button of each transmitter you wish to program.
5. The system will respond with 1 chirp for each accepted transmitter.
6. Turn the ignition OFF to exit transmitter programming.
7. The system will chirp 2 times to confirm exit.
Note: This system has 1 button programming which programs all channels of the transmitter to the
system at once.
Consumer Mode Feature Programming Bank - No Transmitters
1. Turn the ignition ON.
2. Press and release the override button 3 times, the system will chirp 1 time.
3. Turn the ignition OFF, the system will chirp 2 times.
4. Turn the ignition ON, the system will chirp one time indicating option #1 in the feature bank. The
LED will flash the current setting for the option.
5. Use the override button to scroll through the selections in the feature bank, the system will chirp to
match the feature number.
6. Press the programming button on the module to change the desired feature. The LED will flash
indicating the features setting.
7. Turn the ignition OFF to exit programming, the system will chirp 1 time to confirm exit.
Consumer Mode Feature Programming Bank - With Transmitters
1. Turn the ignition ON.
2. Press and release the override button 3 times, the system will chirp 1 time.
3. Turn the ignition OFF, the system will chirp 2 times.
4. Turn the ignition ON, the system will chirp one time indicating option #1 in the feature bank. The
LED will flash the current setting for the option.
5. Use the CAR FIND/PANIC button to scroll through the selections in the feature bank, the system will
chirp to match the feature number.
6. Press the LOCK button to change the desired feature. The LED will flash indicating the changed
feature.
7. Turn the ignition OFF to exit programming, the system will chirp 1 time to confirm exit.
Defaulting the Features in the Feature Programming Bank
1. Turn the ignition ON.
2. Press and release the override button 3 times, the system will chirp 1 time.
4. Press the programming button on the module, the system will chirp 4 times indicating the features
have been defaulted.
NOTE: The system will remain in programming mode as long as the ignition is on, there is no
time limit. To exit programming turn the IGNITION OFF.
4
Transmitter Programming Bank
Feature Programming Bank 1 LED Flash 2 LED Flashes 3 LED Flashes
1. Security Function ON OFF
2. Passive Locks Passive Active
3. Silent Choice ON OFF
4. Passive/Active Arming Passive Active
5. Siren/Horn Siren Horn
6. Door Trigger Delay Instant 15 Second
7. Arm 2 Input Polarity NEG POS
8. Chirps ON OFF
9. Extended Locks 0.9 sec. 3 sec. Dbl pulse U/L
10. Ignition Controlled Locks ON OFF
11. Dk Blue Wire Output Trunk ITS Function
12. Disarm 2 Input Polarity NEG POS
13. Horn Output Timing 16mS 40mS 72mS
14. Real Panic Sound ON OFF
Note: Default settings are in BOLD print.
Changing option #11 to ITS Function changes the functionality of the entire system, refer to the ITS Functionality
section on page 22 of this manual.
CONSUMER MODE PROGRAMMING GUIDE
Dome Light Delay/Theater Lighting Programming
The system can be programed to delay arming after the lock button is pressed (60 second max) for vehicles
with a dome light delay or theater dimming feature. Once programed the system will ‘learn’ the timing of the
dome light delay and add 2 seconds before arming.
1. Close all doors with ignition off.
2. Using the transmitter press LOCK, UNLOCK, LOCK ,UNLOCK, LOCK , UNLOCK, LOCK. The LED will light
solid to indicate the system has entered DOME DELAY LEARN MODE.
3. Immediately OPEN then CLOSE the door WITHOUT disarming the system. The system will then monitor the
door trigger wire. Once the dome light turns off, the system will then add 2 seconds and then exit the
learning mode.
4. The LED will begin to flash indicating the system has exited the learning mode and is now armed.
SETUP & PROGRAMMING - CONSUMER MODE, CONTINUED
5
SETUP & PROGRAMMING - LOT MODE
Lot Mode Transmitter Programming Bank - ACM Transmitter
1. Turn the ignition ON.
2. Press and release the override button 3 times.
3. The system will chirp 1 time.
4. Enter the desired VEHICLE NUMBER into the ACM keypad and then press the LOCK button.
5. The system will respond with 1 chirp.
6. Turn the ignition OFF to exit transmitter programming.
7. The system will chirp 2 times to confirm exit.
Note: This system has 1 button programming which programs all channels of the transmitter to the
system at once.
When an ACM keypad is programmed to the system, it is automatically transitioned into Lot Mode.
Only 1 vehicle number may be learned to the system.
Lot Mode Feature Programming Bank - No ACM Transmitter
1. Turn the ignition ON.
2. Press and release the override button 3 times, the system will chirp 1 time.
3. Turn the ignition OFF, the system will chirp 2 times.
4. Turn the ignition ON, the system will chirp one time indicating option #1 in the feature bank. The
LED will flash the current setting for the option.
5. Use the override button to scroll through the selections in the feature bank, the system will chirp to
match the feature number.
6. Press the programming button on the module to change the desired feature. The LED will flash
indicating the features setting.
7. Turn the ignition OFF to exit programming, the system will chirp 1 time to confirm exit.
Lot Mode Feature Programming Bank - With ACM Transmitter
1. Turn the ignition ON.
2. Press and release the override button 3 times, the system will chirp 1 time.
3. Turn the ignition OFF, the system will chirp 2 times.
4. Turn the ignition ON, the system will chirp one time indicating option #1 in the feature bank. The
LED will flash the current setting for the option.
5. Use the CAR FIND/PANIC button to scroll through the selections in the feature bank, the system will
chirp to match the feature number.
6. Press the LOCK button to change the desired feature. The LED will flash indicating the changed
feature.
7. Turn the ignition OFF to exit programming, the system will chirp 1 time to confirm exit.
Defaulting the Features in the Feature Programming Bank
1. Turn the ignition ON.
2. Press and release the override button 3 times, the system will chirp 1 time.
4. Press the programming button on the module, the system will chirp 4 times indicating the features
have been defaulted.
NOTE: The system will remain in programming mode as long as the ignition is on, there is no
time limit. To exit programming turn the IGNITION OFF.
6
Transmitter Programming Bank
Feature Programming Bank 1 LED Flash 2 LED Flashes 3 LED Flashes
1. Security Function ON OFF
2. Passive Locks Passive Active
3. Silent Choice ON OFF
4. Passive/Active Arming Passive Active
5. Siren/Horn Siren Horn
6. Door Trigger Delay Instant 15 Second
7. Arm 2 Input Polarity NEG POS
8. Chirps ON OFF
9. Extended Locks 0.9 sec. 3 sec. Dbl pulse U/L
10. Ignition Controlled Locks ON OFF
11. Dk Blue Wire Output Trunk ITS Function
12. Disarm 2 Input Polarity NEG POS
13. Horn Output Timing 16mS 40mS 72mS
14. Real Panic Sound ON OFF
15. Lot Alert OFF ON
Note: Default settings are in BOLD print.
Changing option #11 to ITS Function changes the functionality of the entire system, refer to the ITS Functionality
section on page 22 of this manual.
LOT MODE PROGRAMMING GUIDE
Dome Light Delay/Theater Lighting Programming
The system can be programed to delay arming after the lock button is pressed (60 second max) for vehicles
with a dome light delay or theater dimming feature. Once programed the system will ‘learn’ the timing of the
dome light delay and add 2 seconds before arming.
1. Close all doors with ignition off.
2. Using the transmitter press LOCK, UNLOCK, LOCK ,UNLOCK, LOCK , UNLOCK, LOCK. The LED will light
solid to indicate the system has entered DOME DELAY LEARN MODE.
3. Immediately OPEN then CLOSE the door WITHOUT disarming the system. The system will then monitor the
door trigger wire. Once the dome light turns off, the system will then add 2 seconds and then exit the
learning mode.
4. The LED will begin to flash indicating the system has exited the learning mode and is now armed.
SETUP & PROGRAMMING - LOT MODE
7
Transitioning into Lot Mode - ACM Transmitter
1. Turn the ignition ON.
2. Press and release the override button 3 times.
3. The system will chirp 1 time.
4. Enter the desired VEHICLE NUMBER into the ACM keypad and then press the LOCK button.
5. The system will respond with 1 chirp.
6. Turn the ignition OFF to exit transmitter programming.
7. The system will chirp 2 times to confirm exit.
Note: This system has 1 button programming which programs all channels of the transmitter to the
system at once.
Use of an ACM keypad is required.
Once an ACM keypad is programmed to the system, it is automatically transitioned into Lot Mode.
Only 1 vehicle number may be learned to the system.
When in lot mode, a consumer remote can not be programmed to the system until it is transitioned to
consumer mode.
All programming features will be defaulted to the factory default settings.
Transitioning into No-Sale Mode - YELLOW
1. Open a vehicle door.
2. Enter the vehicle number into an ACM keypad.
3. Press the UNLOCK button.
4. Press and release the # button.
5. Press and release the “YELLOW” button.
6. Close the vehicle’s door.
Note: The ACM keypad must be authorized for transitioning.
Note: No-Sale mode disables all functionality of the unit, the unit will be inoperable until reprogrammed
with the PROPLPR programming device. This mode is only used when there is a no-sale of the product
and you are not removing the system from the vehicle.
TRANSITIONING BETWEEN MODES - ACM TRANSMITTER
Transitioning into ITS Mode - GREEN
1. Open a vehicle door.
2. Enter the vehicle number into an ACM keypad.
3. Press the UNLOCK button.
4. Press and release the # button.
5. Press and release the “GREEN” button.
6. Close the vehicle’s door.
Note: The ACM keypad must be authorized for transitioning.
Note: ITS mode enables the shock sensor only of this device for applications in a vehicle equipped with
a factory security system.
8
Transitioning into Factory Keyless Upgrade Mode - BLUE
1. Open a vehicle door.
2. Enter the vehicle number into an ACM keypad.
3. Press the UNLOCK button.
4. Press and release the # button.
5. Press and release the “BLUE” button.
6. The LED will flash blue 1 time and the system will chirp 3 times.
7. Close the vehicle’s door.
Note: The ACM keypad must be authorized for transitioning.
Note: Factory Keyless Upgrade Mode enables all of the device’s security functionality by use of the
factory transmitters.
TRANSITIONING BETWEEN MODES - ACM TRANSMITTER, CONTINUED
Transitioning into Security with Transmitters Mode - RED
1. Open a vehicle door.
2. Enter the vehicle number into an ACM keypad.
3. Press the UNLOCK button.
4. Press and release the # button.
5. Press and release the “RED” button.
6. The LED will flash red 1 time and the system will chirp 3 times.
7. Within 5 seconds program the aftermarket transmitter by pressing the lock button of each transmit-
ter you wish to program.
8. Close the vehicle’s door.
Note: The ACM keypad must be authorized for transitioning.
Note: If no remotes are programmed during step 7, the system will automatically transition into the
Factory Keyless Upgrade Mode - BLUE
Note: Security with Transmitters Mode enables all of the device’s security functionality by use of
aftermarket transmitters.
9
Transitioning into Lot Mode
1. Turn the ignition ON.
2. Press and release the override button 3 times.
3. The system will chirp 1 time.
4. Press button 1 of the short range transmitter.
5. The system will respond with 1 chirp.
6. Turn the ignition OFF to exit transmitter programming.
7. The system will chirp 2 times to confirm exit.
Note: This system has 1 button programming which programs all channels of the transmitter to the
system at once.
When in lot mode, a consumer remote can not be programmed to the system until it is transitioned to
consumer mode.
All programming features will be defaulted to the factory default settings.
TRANSITIONING BETWEEN MODES - SHORT RANGE TRANSMITTER
Transitioning into Consumer Mode
1. Open a vehicle door.
2. Press and hold button 2 of the short range transmitter until the system chirps 3 times.
3. Again press and hold button 2 of the short range transmitter until the system chirps 3 times.
4. Within 5 seconds program a consumer remote. If no remotes are programmed in the 5 second
window, the system will default to a factory keyless upgrade setting which uses the factory remote
controls to arm and disarm the system.
Note: Programming features 1-4 will be defaulted to the factory default settings, programming features
5-13 will retain any changes that have been made.
ON BOARD SHOCK SENSOR
Adjusting the Shock Sensor
1. Increase sensitivity by turning the adjustment dial clockwise.
2. Decrease sensitivity by turning the adjustment dial counter clockwise.
Testing the Shock Sensor
Arm the system and wait 6 seconds for the zone to stabilize, then firmly strike the vehicles bumper.
10
1. 8 PIN MAIN HARNESS
BLACK - Chassis Ground Source (-)
Connect the BLACK wire to a solid chassis ground point using a ring terminal and self tapping screw (not
supplied). Scrape away paint from the grounding point to ensure a good connection. The recommended
grounding point is a metal surface in the driver’s side kick panel area.
Note: Do not ground the BLACK wire with any other vehicle components.
YELLOW - 12 Volts Ignition Input (+)
Locate the vehicle’s ignition wire at the ignition switch.
Verification: This wire registers voltage when the key is turned to the ON (or RUN) position. The voltage
does not drop out when the key is turned to the START (or CRANK) position.
Connect the YELLOW wire to the vehicle’s Ignition wire.
PURPLE - Positive Door Input (+)
Locate the vehicle’s dome light or door pin switch wire.
Verification: This wire will register positive voltage (POS) when the door is opened and the interior light is on.
This wire will register ground or "0" Volts when the door is closed and the interior light is off.
Connect the PURPLE wire to the vehicle’s positive door input wire(s).
NOTE: Certain vehicles may require multiple connections. Refer to vehicle application guide
RED/WHITE - 12 Volt Battery Power (+)
Locate 1 of the vehicle’s constant 12 Volt battery wires at the ignition switch.
Verification: This wire will register voltage in all positions of the ignition switch.
Connect the RED/WHITE wire to the constant 12 Volt battery wire.
Note: Remove the in-line fuse until all connections are made.
WHITE - Parking Light Output (+/-) / RED - Parking Light Polarity
Locate the vehicle’s parking light wire at the vehicle light switch.
Verification: This wire will register positive voltage or ground when the vehicle parking light switch is turned
to the ON position.
These wires are the COMMON and NORMALLY OPEN contacts of the on-board parking light relay. If the
vehicle's parking lights are a +12 volt switched system, connect the RED wire to a fused +12 volt battery
source, and connect the WHITE wire to the vehicle's parking light wire. If the vehicle's parking lights are a
chassis ground switched system, connect the RED wire to a chassis ground source, and connect the WHITE
wire to the vehicle's parking light wire.
11
1. 8 PIN MAIN HARNESS, CONTINUED
BROWN - Negative Door Input (-)
Locate the vehicle’s dome light or door pin switch wire.
Verification: This wire will register ground (NEG) when the door is opened and the interior light is on. This
wire will register positive voltage when the door is closed and the interior light is off.
Connect the BROWN wire to the vehicle’s negative door input wire(s).
NOTE: Certain vehicles may require multiple connections. Refer to vehicle application guide
ORANGE - Armed Output (-) 500mA
This wire will show ground when the system is armed. This wire is used for controlling a starter interrupt relay,
window modules or other additional sensors.
2. 6 PIN HARNESS
DK GREEN - Instant Trigger Input (-)
This wire is a ground input for an external sensor, trunk pin or secondary pin switch.
Verification: This wire when connected will trigger the security system
BLACK/WHITE - Horn Output (-) 1Amp
Locate the vehicle’s horn wire at the steering column.
Verification: This wire will register at positive voltage and register ground when the horn switch is pressed.
Connect the BLACK/WHITE wire to the vehicle’s horn wire.
LT GREEN - Hood Pin Input (-)
Install the supplied Hood Pin Switch and connect to the LT GREEN wire.
Verification: This wire when connected will register ground when the vehicle's hood is opened.
Connect the LT GREEN wire to the hood pin.
NOTE: Be sure to loom the wire, and seal the grommet.
GREEN/WHITE - Illuminated Entry Output (-) 300mA
This wire provides a 300mA output for 30 seconds when the system is disarmed and a continuous output
when the system is triggered.
Locate the vehicle’s dome light or pin switch wire.
Verification: This wire will register positive voltage or ground when the vehicle's dome light is turned ON.
12
2. 6 PIN HARNESS, CONTINUED
DK BLUE - Trunk Release Output (-)
This wire provides a 500mA negative output capable of driving relays. For Control of optional accessories
such as trunk release.
To Activate press and hold UNLOCK for 2 seconds.
Locate the vehicle’s trunk release wire at the trunk release switch.
Verification: This wire will register either positive voltage or ground when the trunk release is activated.
3. 5 PIN HARNESS
BLUE - Trunk Shunt Input (+)
This wire when activated will shunt all security zones for 60 seconds or until cleared.
RED - Disarm Input (+/-)
This wire will DISARM the security system when a POS or NEG pulse is applied to it from an external device such
as the vehicle's factory unlock motor wire.
GREEN - Arm Input (+/-)
This wire will ARM the security system when a POS or NEG pulse is applied to it from an external device such as
the vehicle's factory lock motor wire.
RED/BLACK - Disarm Input 2 (+/-)
This wire will prevent the system from disarming the security system when a POS or NEG pulse is applied to it
from an external device. This will prevent the system from disarming if it is pulsed at the same time as the RED
(Disarm Input) wire.
For example: To prevent the system from disarming from the switch on the door. Connect this wire to the unlock
switch or passenger unlock motor wire
NOTE: Only required if using the factory keyless entry transmitter to ARM/DISARM this system.
GREEN/BLACK - Arm Input 2 (+/-)
This wire will prevent the system from arming the security system when a POS or NEG pulse is applied to it from
an external device. This will prevent the system from disarming if it is pulsed at the same time as the GREEN
(Arm Input) wire.
For example: To prevent the system from disarming from the switch on the door. Connect this wire to the unlock
switch or passenger lock motor wire
NOTE: Only required if using the factory keyless entry transmitter to ARM/DISARM this system.
13
4. 3 PIN DOOR LOCK HARNESS
RED - Lock Output (-)
GREEN - Unlock Output (-)
RED/BLACK - 2nd Door Unlock Output
Negative Switching and Negative Switching with 2-step unlock feature:
All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock switch.
Verification: These wires will register ground when the lock and unlock switches are activated.
Driver’s Door Unlock: Locate the unlock motor wire directly from the actuator inside the driver’s door.
Verification: This wire will rest at ground and register positive voltage when the driver’s door is unlocked.
Connect the RED and GREEN or RED/BLACK wires shown in the diagram below.
Note: When adding the 2 step unlock feature the RED/BLACK 2nd door unlock wire will be used to unlock all
vehicle doors on the second press of unlock. An additional SPDT relay (not supplied) is required. Connect
the relay as shown in the diagram below to unlock the driver’s door on the first press of unlock.
Lock
Unlock
87
87a
86 85
30
Vehicle Door Lock
Control Relays
RED (-) Lock Output
GREEN (-) Unlock Output or
RED/BLACK 2nd Unlock
Output for 2 Step Unlock
F
or 2 Step Unlock:
Fused +12 Volt
Battery Souce
GREEN (-) Unlock Output
From Keyless Entry
Module or Door
Unlock Relay
Drivers Door
Unlock Motor Wire
X
Cut
Negative Locks:
14
RED - Lock Output (-)
GREEN - Unlock Output (-)
RED/BLACK - 2nd Door Unlock Output
Positive Switching and Positive Switching with 2-step unlock feature:
All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock switch.
Verification: These wires will register positive voltage when the lock and unlock switches are activated.
Driver’s Door Unlock: Locate the unlock motor wire directly from the actuator inside the driver’s door.
Verification: This wire will rest at ground and register positive voltage when the driver’s door is unlocked.
Connect the RED and GREEN or RED/BLACK wires shown in the diagram below.
Note: When adding the 2 step unlock feature the RED/BLACK 2nd door unlock wire will be used to unlock all
vehicle doors on the second press of unlock. Two additional SPDT relays (not supplied) are required.
Connect the relays as shown in the diagram below to unlock the driver’s door on the first press of unlock.
Lock
Unlock
87
87a
86 85
30
87
87a
86 85
30
87
87a
86 85
30
Vehicle Door Lock
Control Relays
Fused +12 Volt
Battery Souce
Fused +12 Volt
Battery Souce
RED (-) Lock Output
GREEN (-) Unlock Output o
r
RED/BLACK 2nd Unlock
Output for 2 Step Unlock
For 2 Step Unlock:
Fused +12 Volt
Battery Souce
GREEN (-) Unlock Output
From Keyless Entry
Module or Door
Unlock Relay
Drivers Door
Unlock Motor Wire
X
Cut
Positive Locks:
4. 3 PIN DOOR LOCK HARNESS, CONTINUED
15
RED - Lock Output (-)
GREEN - Unlock Output (-)
RED/BLACK - 2nd Door Unlock Output
One Wire Negative Multiplexed and One Wire Negative Multiplexed with 2-step Unlock Feature:
All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock switch.
Verification: This wire will show variable ground when the switch is activated. Please consult the Vehicle
Wire Color and Location Chart for specific resistor values for the vehicle.
Driver’s Door Unlock: Locate the unlock motor wire directly from the actuator inside the driver’s door.
Verification: This wire will rest at ground and register positive voltage when the driver’s door is unlocked.
Connect the RED and GREEN or RED/BLACK wires shown in the diagram below using (2) SPDT relays (not
supplied).
Note: When adding the 2 step unlock feature the RED/BLACK 2nd door unlock wire will be used to unlock all
vehicle doors on the second press of unlock. An additional SPDT relay (not supplied) is required. Connect
the relay as shown in the diagram below to unlock the driver’s door on the first press of unlock.
Lock
Unlock
87
87a
86 85
30
Vehicle Door Lock
Control Relays
RED (-) Lock Output GREEN (-) Unlock Output o
r
RED/BLACK 2nd Unlock
Output for 2 Step Unlock
For 2 Step Unlock:
Fused +12 Volt
Battery Souce
GREEN (-) Unlock Output
From Keyless Entry
Module or Door
Unlock Relay
Drivers Door
Unlock Motor Wire
X
Cut
Multiplex Locks:
87
87a
86
30
87
87a
86
30
85 85
Fused +12 Volt
Battery Source
Ground
Resistor
4. 3 PIN DOOR LOCK HARNESS, CONTINUED
16
RED - Lock Output (-)
GREEN - Unlock Output (-)
RED/BLACK - 2nd Door Unlock Output
One Wire Positive Multiplexed and One Wire Multiplexed With 2-step Unlock Feature
All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock switch.
Verification: This wire will show variable positive voltage when the switch is activated. Please consult the
Vehicle Wire Color and Location Chart for specific resistor values for your vehicle.
Driver’s Door Unlock: Locate the unlock motor wire directly from the actuator inside the driver’s door.
Verification: This wire will rest at ground and register positive voltage when the driver’s door is unlocked.
Connect the RED and GREEN or RED/BLACK wires shown in the diagram below using (2) SPDT relays (not
supplied).
Note: When adding the 2 step unlock feature the RED/BLACK 2nd door unlock wire will be used to unlock all
vehicle doors on the second press of unlock. An additional SPDT relay (not supplied) is required. Connect
the relay as shown in the diagram below to unlock the driver’s door on the first press of unlock.
Lock
Unlock
87
87a
86 85
30
Vehicle Door Lock
Control Relays
RED (-) Lock Output GREEN (-) Unlock Output o
r
RED/BLACK 2nd Unlock
Output for 2 Step Unlock
For 2 Step Unlock:
Fused +12 Volt
Battery Souce
GREEN (-) Unlock Output
From Keyless Entry
Module or Door
Unlock Relay
Drivers Door
Unlock Motor Wire
X
Cut
Multiplex Locks:
87
87a
86
30
87
87a
86
30
85 85
Fused +12 Volt
Battery Source
Resistor
4. 3 PIN DOOR LOCK HARNESS, CONTINUED
17
RED - Lock Output (-)
GREEN - Unlock Output (-)
RED/BLACK - 2nd Door Unlock Output
Reverse Polarity (5-Wire Door locks) and Reverse Polarity with 2-step Unlock
All Door Lock and Unlock: Locate the lock / unlock wire at the vehicle’s lock / unlock switch.
Verification: These wires will rest at ground and register positive voltage when the lock and unlock switches
are activated.
Driver’s Door Unlock: Locate the unlock motor wire directly from the actuator inside the driver’s door.
Verification: This wire will rest at ground and register positive voltage when the driver’s door is unlocked.
Connect the RED and GREEN or RED/BLACK wires shown in the diagram below using (2) SPDT relays (not
supplied).
Note: When adding the 2 step unlock feature the RED/BLACK 2nd door unlock wire will be used to unlock all
vehicle doors on the second press of unlock. An additional SPDT relay (not supplied) is required. Connect
the relays as shown in the diagram below to unlock the driver’s door on the first press of unlock.
Lock
Unlock
87
87a
86 85
30
87
87a
86 85
30
87
87a
86 85
30
Fused +12 Volt
Battery Souce
Fused +12 Volt
Battery Souce
RED (-) Lock Output
GREEN (-) Unlock Output or
RED/BLACK 2nd Unlock
Output for 2 Step Unlock
F
or 2 Step Unlock:
Fused +12 Volt
Battery Souce
GREEN (-) Unlock Output
From Keyless Entry
Module or Door
Unlock Relay
Drivers Door
Unlock Motor Wire
X
Cut
Reverse Polarity Locks:
X
Cut
X
Cut
To Door Lock Motor
To Door Lock Motor
4. 3 PIN DOOR LOCK HARNESS, CONTINUED
18
RED - Lock Output (-)
GREEN - Unlock Output (-)
RED/BLACK - 2nd Door Unlock Output
Adding Door Actuators
After installing door actuators, (not supplied). Connect the RED and GREEN wires shown in the diagram
below using (2) SPDT relays (not supplied).
30
87
87a
86 85
Fused +12 Volt
Battery Source
Door Lock
Actuator
30
87
87a
86 85
Chassis
Ground
Chassis
Ground
RED (-) Lock Output
GREEN (-) Unlock Outpu
t
Fused +12 Volt
Battery Source
M
4. 3 PIN DOOR LOCK HARNESS, CONTINUED
19
5. ACCESSORY CONNECTORS
6 Pin Override Push-Button and LED
The status LED / override button should be mounted in a visible and easily accessible location on the
driver’s dashboard area. Route the harness and plug the 6 pin connector into the module.
4 Pin Tracking Port: (Off White Connector)
This 4 pin port is used for connecting the PROPT20 PursuiTrak GPS system.
4 Pin Data Bus Interface Port: (Brown Connector)
This 4 pin port is used for Flashlogic Door Lock and Transponder Databus Interfaces to communicate with
the vehicle's Databus. When using the DBI port to control the Flashlogic Door Lock and Transponder
Interface modules the following options may be available. Please refer to the D2D (Data to Data) function list
available per vehicle on the tech service web site.
Door Trigger Trunk/Hatch Open
Keyless Entry Control Dome Light Supervision
Factory Alarm Arm / Disarm Manual Arm / Disarm Inputs (factory keyless controls system)
20
7. System Testing
1. Follow each instruction below.
2. Verify that the system operates as indicated under each instruction. Refer to the system owners manual.
3. Check the appropriate wire connections and/or fuses if the unit fails to perform a specific function. Also
check that any options pertaining to the function are programmed properly.
Security Operation
Press LOCK once:
1. Doors lock.
2. Courtesy lights (if on) shut off.
3. Unit checks to see if doors, hood or trunk are open. If open, siren (or horn) sounds once, parking lights
flash once, and system enters pre-arm mode.
Pre-arm mode:
1. The unit will wait for the open door, hood or trunk to be closed. The LED is solid during pre-arm.
2. If the entrance is secured, the siren/horn will sound again, parking lights will flash once, and the system will
arm.
3. If the entrance is not secured after 4 minutes, the siren/horn will sound again, parking lights will flash once,
the system will arm, and the defective trigger or entrance will be ignored.
Note: If entrance is secured after 4 minutes, the system will immediately begin to monitor the entrance for
intrusion.
If the above conditions are not present:
1. Vehicle starter is disabled.
2. Siren (or horn) sounds twice / parking lights flash twice.
3. LED (Red light) flashes slowly for duration of arm cycle.
4. After 5 seconds, unit monitors all entrances and sensors.
If door, sensor, hood/trunk or ignition input is triggered:
1. Siren/horn sounds for 30 seconds or until UNLOCK is pressed.
2. Parking lights flash.
3. If the alarm system is triggered, pressing UNLOCK (once) will end the 30-second cycle.
Pressing UNLOCK after a full 30 second trigger cycle has completed, the horn will honk 4 times and the LED
will flash a number of times to indicate which input triggered the alarm. Turning on the ignition or pressing
the valet/override button will reset the LED flashes, pressing the valet/override button will also honk the
horn to match the LED flashes before it resets.
Number of flashes:
1 - Interior Theft Sensor (Shock Sensor)
2 - Door Input
3 - Hood
4 - Trunk input
5 - Ignition
6. SYSTEM POWER-UP PROCEDURE
1. After all connections are complete, turn the vehicle's ignition key to the ON position.
2. Insert the 5 Amp fuse into the respective fuseholder.
3. Turn the ignition key to the OFF position.
21
Press DISARM:
1. Doors unlock.
2. Factory alarm (if equipped) is turned off.
3. Siren/horn sounds once/ parking lights flash once.
4. Courtesy lights turn on for 30 seconds, or until ARM is pressed or ignition is turned on.
5. Vehicle starter is enabled.
Press DISARM twice:
Passenger doors unlock if using 2-stage unlock.
Press CAR FIND/PANIC:
Siren/horn sounds 5 times.
Press and hold CAR FIND/PANIC for 2 seconds:
Siren/horn sounds and lights flash for 30 seconds or until any remote control button is pressed.
Press and hold TRUNK:
Trunk or hatch opens, or other device activates.
If the Ignition Controlled Locks option is set to On:
Doors lock when all doors are closed and the ignition is turned ON.
Doors unlock when ignition is turned OFF.
8. SYSTEM TESTING, CONTINUED
9. MOUNTING THE MODULE / FINISHING INSTALLATION
Mount the module to a brace or wire harness under the dash. The module and harnesses must be clear of
moving parts.
Installation Complete.
22
ITS Introduction
The PRO PLM may be used as a ITS (Interior Theft Sensor) and when doing so it is designed to honk the horn if a
light impact is detected or trigger the vehicle's factory alarm if a harder impact is detected.
Note: The vehicle MUST have a factory alarm that is triggered by opening the vehicle's door.
Option #10 must be changed in the feature programming bank for the system to function as the ITS.
Optional Warn Away
The optional Warn-Away Trigger is active after the ignition key is turned off and the dome light shuts off after exiting
the vehicle. When a light impact is detected the system will briefly honk the vehicles horn. If at any time a door is
opened (dome light "on"), the Warn-Away Trigger will be bypassed until the ignition key is cycled "ON" and "OFF".
This feature prevents the Warn-Away chirps of the vehicle's horn when the customer/user enters the vehicle. The
Warn-Away Trigger will reactivate when the ignition key is cycled "ON" and "OFF" again.
Factory Alarm Trigger
The ITS Factory Alarm Trigger is active 5 minutes after the ignition is turned off and the factory alarm has been set.
When a heavy impact is detected the ITS will pulse the vehicle's door trigger wire to active the factory alarm.
Valet Mode
Valet Mode deactivates both the optional Warn-Away and Factory Alarm Trigger. To turn Valet Mode ON, turn the
ignition key ON/OFF three times. To turn Valet Mode "OFF", turn the ignition key ON/OFF three times.
Harness Connections
DK BLUE - Factory Alarm Trigger: Connect this to a wire which triggers the vehicle's factory alarm system such as
the door ajar, hood or trunk wire.
PURPLE and BROWN - Door Inputs (+/-): Connect one of these wires to the vehicle's dome light wire.
RED - +12 Volt Input: Connect this wire to constant +12 volt source.
BLACK - Ground Input: Connect this wire to chassis ground.
YELLOW - Ignition Input: Connect this wire to +12 volt ignition source.
BLACK/WHITE - Warn Away Horn Output: Connect this wire to the vehicle's horn wire.
NOTES:
The ITS uses the PURPLE or BROWN (Door Input) to DISARM the optional Warn-Away feature. The PURPLE or
BROWN must sense all of the doors for the ITS to DISARM properly. It is recommended to only use the Warn-Away
feature with vehicle's that have an "ALL" door trigger output in the vehicle.
ITS ACTIVATION
ITS FUNCTIONALITY
23
ITS LAYOUT
BLACK GROUND
YELLOW IGNITION
PURPLE DOOR TRIGGER (+)
RED/WHITE +12 VOLT BATTERY
WHITE N/A
BROWN DOOR TRIGGER (-)
RED N/A
ORANGE N/A
OPEN
DK GREEN N/A
BLACK/WHITE HORN OUTPUT (-)
LT. GREEN N/A
GREEN/WHITE N/A
DK BLUE FACTORY ALARM TRIGGER
BLUE N/A
RED/BLACK N/A
RED N/A
GREEN/BLACK N/A
GREEN N/A
RED/BLACK N/A
GREEN N/A
RED N/A
TRACKING PORT
PROGRAMMING BUTTON
LED / OVERRIDE BUTTON
3 Pin 5 Pin 6 Pin 8 Pin
DBI PORT
SHOCK SENSOR DIAL
PROPLM

Navigation menu