Advanced Card Systems ACR900 Banking POS Terminal User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3668528
Application ID	DjqKBitph05rc1QOUmP4Wg==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	19.91kB (248825 bits)
Date Submitted	2017-12-08 00:00:00
Date Available	2017-12-08 00:00:00
Creation Date	2017-05-05 12:05:13
Producing Software	Foxit Reader PDF Printer Version 8.2.1.0112
Document Lastmod	2017-12-08 11:49:47
Document Title	Users Manual

ACR900 POS Terminal User Manual
I. Installation
1. SAM cards / SIM card / Micro SD card
Unclip the trapdoor on the bottom side of
the terminal by your nails.
Insert SAM cards / SIM card / Micro SD
card to the related card slots.
Close the trapdoor.
2. Rechargeable Battery
Unclip the trapdoor on the bottom side of the terminal by your nails.
Place the battery over the SAM card and SIM card slot. Make sure that metal plates on the
battery would touch with the metal contact
contacts in the battery case of terminal.
Close the trapdoor.
3. Charging the battery
Connect the 9V DC power supply provided
together with ACR900 to the power port on
ACR900.
4. Paper roll
Lift the tab on the printer cover to
open the paper compartment.
Place a paper roll (diameter not
over 37mm) in the compartment
Press simultaneously on both
upper corners of the printer cover
until it clips into position.
5. Connecting to Ethernet, USB devices and Serial
devices
Connect the ACR900 to the interface module with the
specific cable provided together with ACR900.
Connect the Ethernet cable, USB cable or Serial cable
to the specific port on the interface module
II. Operating instruction
1. Turn ON / OFF
Press
button for 3 seconds to Turn ON.
Press
button for 3 seconds until the LCD shows Turn OFF confirm page; Press
button (enter key) to confirm Turn OFF.
2. Sleep / Wake
Press
button and LCD turns off. Press
button again to turn LCD on.
3. Reading Smart Card (contact)
Insert the card horizontally with chip facing upward until the card reaches the end in the card slot.
Leave the card in the card slot throughout a transaction.
4. Reading Smart Card (contactless)
Tap the card firmly in the active zone over the printer cover. Keep the card close to the zone
during a transaction.
5. Reading Magnetic Stripe Card
Swipe the card with the stripe facing to the terminal either from top to bottom or bottom to top.
Use a regular movement inside the track.
6. Feeding paper
Press
button to feed paper. DO NOT pull the paper by hand.
7. Tearing the printing paper
Pull the receipt against the printer cutter at an angle either from left to right or from right to left.
III. Caution
Never disassemble the terminal without approval.
Only use the power supply included with the terminal or provided by ACS
Turn off the terminal before opening the trapdoor.
Avoid the terminal contact with water.
IV. Rechargeable Battery
Only use the rechargeable battery provided together with the terminal or provided by ACS.
Avoid placing the battery directly under the sun, or environment of high temperature or high
humidity.
Do not short-circuit the battery
Do not disassemble the battery
FCC Caution.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
‐Reorient or relocate the receiving antenna.
‐Increase the separation between the equipment and receiver.
‐Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
‐Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement:
Specific Absorption Rate (SAR) information
SAR tests are conducted using standard operating positions accepted by the FCC
with the Bank ing P OS Terminal transmitting at its highest certified power level in all tested frequency
bands, although the SAR is determined at the highest certified power level, the actual
SAR level of the Bank ing P OS Terminal while operating can be well below the maximum value. Before
a new model Bank ing P OS Terminal is a available for sale to the public, it must be tested and certified
to the FCC that it does not exceed the exposure limit established by the FCC, tests for
each Banki ing P OS Terminal are performed in positions and locations as required by the FCC. For
body worn operation, this model Banki ing P OS Terminal has been tested and meets the FCC RF
exposure guidelines when used with an accessory designated for this product or when
used with an accessory that contains no metal.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Author                          : 
Create Date                     : 2017:05:05 12:05:13+08:00
Modify Date                     : 2017:12:08 11:49:47-08:00
Subject                         : 
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Format                          : application/pdf
Creator                         : 
Description                     : 
Title                           : 
Creator Tool                    : 
Metadata Date                   : 2017:12:08 11:49:47-08:00
Keywords                        : 
Producer                        : Foxit Reader PDF Printer Version 8.2.1.0112
Document ID                     : uuid:ed464eb3-a91b-49e8-9a86-97619e86c5ca
Instance ID                     : uuid:654e28e9-7884-44a1-8efa-38fc18d0e19a
Page Count                      : 3

EXIF Metadata provided by EXIF.tools