Advanced Card Systems EH880 Smart Card Terminal User Manual
Advanced Card Systems Limited Smart Card Terminal Users Manual
Users Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1225582 |
| Application ID | W7Jtw6hyc4AI8t2OX3rR2A== |
| Document Description | Users Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 53.66kB (670748 bits) |
| Date Submitted | 2010-01-11 00:00:00 |
| Date Available | 2010-01-11 00:00:00 |
| Creation Date | 2009-12-31 17:35:38 |
| Producing Software | Acrobat Distiller 8.0.0 (Windows) |
| Document Lastmod | 2010-01-06 10:38:16 |
| Document Title | Microsoft Word - eH880 and ACR880 SDE Setup Manual V1.4.doc |
| Document Creator | PScript5.dll Version 5.2 |
| Document Author: | a |
eH880 and ACR880 SDE Setup Manual info@acs.com.hk Subject to change without prior notice www.acs.com.hk Revision History Version Date Prepared By 1.4 06 October 2009 Richelle Arjona Description • Changed device photo in front page Page 2 of 20 eH880 and ACR880 SDE Setup Manual Document Title Here Version 1.4 Document Title Here info@acs.com.hk www.acs.com.hk Table of Contents 1.0. Introduction ............................................................................................................... 5 1.1. 1.2. Purpose ........................................................................................................................................5 Scope and Limitations ..................................................................................................................5 2.0. Overview .................................................................................................................... 6 3.0. Compiler and Library Installation on PC Linux ...................................................... 7 3.1. Requirements ...............................................................................................................................7 3.1.1. Operating System..............................................................................................................7 3.1.2. Hardware Requirements ...................................................................................................7 3.2. Compiler Installation(Take Fedora as example) ..........................................................................8 3.2.1. Login your Linux PC as “root”............................................................................................8 3.2.2. Incorporate the necessary files .........................................................................................9 3.2.3. Extract complier files .........................................................................................................9 3.2.4. Logout................................................................................................................................9 3.3. Setup your environment .............................................................................................................10 3.3.1. Login your PC Linux with your username. ......................................................................10 3.3.2. Modify Scripts ..................................................................................................................10 3.3.3. Logout..............................................................................................................................10 3.4. Extract Library ............................................................................................................................10 3.4.1. Login your PC Linux with your own username................................................................10 3.4.2. Copy Files........................................................................................................................10 3.4.3. Extract Files.....................................................................................................................10 3.4.4. Testing the Extracted Files..............................................................................................10 4.0. Device Connection to Host Computer................................................................... 11 4.1. Ethernet......................................................................................................................................11 4.1.1. Cable Restrictions ...........................................................................................................11 4.1.2. RJ45 Cable Types...........................................................................................................11 4.1.3. Login Information.............................................................................................................12 4.2. RS232 ........................................................................................................................................12 4.2.1. Serial Port Configuration .................................................................................................12 5.0. Program/Files Uploading........................................................................................ 13 5.1. 5.2. eH880 / ACR880 File Structure..................................................................................................13 Ethernet Connection...................................................................................................................14 5.2.1. Device to PC Host ...........................................................................................................14 5.2.2. Device to Hub/ Switch to PC Host...................................................................................14 5.3. Upload Types .............................................................................................................................15 5.3.1. FTP (File Transfer Protocol)............................................................................................15 5.3.2. SFTP (Secure FTP).........................................................................................................15 5.3.3. NFS (Network File Server) ..............................................................................................15 Appendix A. Connecting eH880 to the Ethernet Network ............................................ 16 Appendix A.1. Configuring Ethernet Port...........................................................................................16 Appendix A.1.1. Setting up Loop Back Device...............................................................................16 Appendix A.1.2. Setting Up Static IP Address................................................................................17 Appendix A.1.3. Setting up Dynamic IP Address ...........................................................................18 Appendix A.2. Setting up Network File System (NFS) Server...........................................................18 Appendix A.2.1 PC Side .................................................................................................................18 Appendix A.2.2 eH880 side ............................................................................................................18 Appendix A.2.3 NFS (Network File System) ..................................................................................18 Appendix A.3. Showing the Status of Processes ..............................................................................19 Appendix A.4. Miscellaneous Information .........................................................................................20 Appendix A.4.1 User ID and Password ..........................................................................................20 Page 3 of 20 eH880 and ACR880 SDE Setup Manual Document Title Here Version 1.4 Document Title Here info@acs.com.hk www.acs.com.hk Figures Figure 1: Cross-Over Cable............................................................................................................ 11 Figure 2: Straight Cable.................................................................................................................. 11 Figure 3: RJ45 Cables with Jacks Connected................................................................................ 12 Figure 4: Use the Cross-over Cable for PC Host to Device Setup................................................. 14 Figure 5: Use the Straight Cable for Device to Hub/Switch Setup ................................................. 14 Tables Table 1: RJ45 Cable Types...............................................................................................................11 Page 4 of 20 eH880 and ACR880 SDE Setup Manual Document Title Here Version 1.4 Document Title Here info@acs.com.hk www.acs.com.hk 1.0. Introduction 1.1. Purpose The purpose of this documentation is to explain how to setup a software development environment to develop application programs for the eH880 / ACR880 system. The eH880 / ACR880 device is equipped with a 32-bit CPU running the embedded Linux 2.6.12 OS. For detailed hardware / software capability of the eH880 / ACR880, refer to their respective manuals. The software development environment consists of a suite of software tools that are typically run on a PC Linux system. Application software can be developed on the PC Linux and then downloaded to the eH880 / ACR880 for testing and running. This document describes the installation of the software tools on the PC Linux system and also the networking configuration between the PC Linux and the eH880 / ACR880 device. 1.2. Scope and Limitations This document covers the procedures that interact with the device using the TCP/IP protocol. While there are virtually thousands of Linux kernels available on open source programming, the EH880/ACR880 package includes compressed files that are to be integrated to the device. Hardware restrictions and Linux OS versions are also detailed and while the device firmware itself is upgradeable, there are limitations on where files should be copied. Folder restrictions as well as some Linux commands are listed on the succeeding chapters. For this setup the Linux OS that the demo will be using is Debian with a Gnome desktop, version 2.14.3. Page 5 of 20 eH880 and ACR880 SDE Setup Manual Document Title Here Version 1.4 Document Title Here info@acs.com.hk www.acs.com.hk 2.0. Overview • It is assumed that the user has basic knowledge in using computers and operating Linux OS. • Section 3.0 discusses the Linux OS limitations and requirements as well as the compiler instructions upon installation. • Section 4.0 lists the device’s connectivity in both the hardware and software aspects. • Section 5.0 details the folder restrictions when customizing the files inside the device. • Appendix A shows the processes in connecting the eH880 to the Ethernet network. Page 6 of 20 eH880 and ACR880 SDE Setup Manual Document Title Here Version 1.4 Document Title Here info@acs.com.hk www.acs.com.hk 3.0. Compiler and Library Installation on PC Linux 3.1. Requirements 3.1.1. Operating System A Linux based system is required for developing software for eH880. Since the development of the software consists of cross-compilation technique, the developers are expected to have sufficient knowledge to operate Linux system and compile programs using gcc (GNU compiler collection) at least in i386(PC) systems. Developers may use one of the following Linux distributions to develop eH880 software. Debian-based Linux operating systems emphasize on free software for many hardware platforms. This system uses the .deb package format and dpkg package manager. http://www.debianhelp.co.uk/debian.htm Ubuntu-based Linux operating systems, derived from Debian. http://www.kubuntu.org/download.php Fedora-based and Red-Hat-Enterprise-based operating system uses Red Hat Package manager. http://www.fedoralegacy.org/download/ 3.1.2. Hardware Requirements ¾ A modern PC that fulfills the hardware requirements of the above Linux distribution. Page 7 of 20 eH880 and ACR880 SDE Setup Manual Document Title Here Version 1.4 Document Title Here info@acs.com.hk www.acs.com.hk 3.2. Compiler Installation(Take Fedora as example) 3.2.1. Login your Linux PC as “root”. Location Input the root password in the password box. Page 8 of 20 eH880 and ACR880 SDE Setup Manual Document Title Here Version 1.4 Document Title Here info@acs.com.hk www.acs.com.hk 3.2.2. Incorporate the necessary files Go to the root directory “/”, by typing “cd /” on the prompt. Once inside the root directory, copy the file "arm-linux-gcc-3.4.1.tar.bz2" to "/" directory of your PC Linux 3.2.3. Extract complier files Extract the complier files by the command "tar -jxvf arm-linux-gcc-3.4.1.tar.bz2" 3.2.4. Logout Input exit on the command prompt to logout. Page 9 of 20 eH880 and ACR880 SDE Setup Manual Document Title Here Version 1.4 Document Title Here info@acs.com.hk www.acs.com.hk 3.3. Setup your environment 3.3.1. Login your PC Linux with your username. 3.3.2. Modify Scripts Modify your login shell script to include “/usr/local/arm/3.4.1/bin” in the search path. For bash shell, Add the line "export PATH=/usr/local/arm/3.4.1/bin:$PATH" at the end of/.bashrc 3.3.3. Logout 3.4. Extract Library 3.4.1. Login your PC Linux with your own username. 3.4.2. Copy Files Copy the file "eH880-sdk-yyyymmdd.tgz" (where yyyymmdd is a date code) to the installation directory 3.4.3. Extract Files Get into the installation directory and extract the library files by the command "tar -zxvf A880-sdkyyyymmdd.tgz" Files to verify: /sdk/.version /sdk/demo : /sdk/sdk-lib : 3.4.4. Version log Some demo program Library and Header file for the API Testing the Extracted Files To test the installation, go to the directory /sdk/demo/demo1 and type "make". The "Makefile" will be read and "arm-linux-gcc" will be invoked then the files "demo1" will be generated at /sdk/demo/demo1/bin Page 10 of 20 eH880 and ACR880 SDE Setup Manual Document Title Here Version 1.4 Document Title Here info@acs.com.hk www.acs.com.hk 4.0. Device Connection to Host Computer 4.1. Ethernet 4.1.1. Cable Restrictions The eH880/ACR880 uses an RJ45 straight cable to connect to a router/ hub. However, a crossover RJ45 cable is used when the device is directly connected to the host pc. See Appendix A for cable types. To connect the PC Linux to the device using the RJ45 cable, insert both ends of the cable jack to the designated ports found on each party. From the command prompt or terminal prompt, key-in “telnet ” for Windows/Linux, or “SSH ” for Linux. 4.1.2. RJ45 Cable Types Pin ID Cross over cable Side A Side B Orange-white Green-white Orange Green Green-white Orange-white Blue Brown-white Blue-white Brown Green Orange Brown-white Blue Brown Blue-white Table 1: Figure 1: Figure 2: Straight cable Side A Side B Orange-white Orange-white Orange Orange Green-white Green-white Blue Blue Blue-white Blue-white Green Green Brown-white Brown-white Brown Brown RJ45 Cable Types Cross-Over Cable Straight Cable Page 11 of 20 eH880 and ACR880 SDE Setup Manual Document Title Here Version 1.4 Document Title Here info@acs.com.hk www.acs.com.hk Figure 3: 4.1.3. RJ45 Cables with Jacks Connected Login Information The IP can be obtained by pressing key when the demo program is running To login and access the eh880, use console (RS232, refer to 4.2) or telnet/ssh (refer to 4.1) to login the device. (username: root, password: cdy123) 4.2. RS232 4.2.1. Serial Port Configuration Signal Level Baud Rate Data Bit Parity Stop Bit Flow Control RS232 (9 pin) 115200 bps None None Connect to the device using the RS232 9 pin serial port to the female port located at the back of the device. The male port counterpart is located at the pc. The login, if required, is till root and the password is cdy123. Certain tools can be used to connect to the device using a serial cable; Hyperterminal is used for Windows and Minicom for Linux. If you connect the RS232 cable to the PC and eh880 after the eh880 powered up, press “enter” in the terminal window to get the login prompt. Page 12 of 20 eH880 and ACR880 SDE Setup Manual Document Title Here Version 1.4 Document Title Here info@acs.com.hk www.acs.com.hk 5.0. Program/Files Uploading 5.1. eH880 / ACR880 File Structure The eH880/ACR880 follows the common Linux file directory structure. The root file system is readonly. The eH880/ACR880 files are stored in the following directories: /usr/local/RO/ For read-only files, such as the unit name and serial number, and other system files. /usr/local/RW For read-write files. Developers can store their software application and data files in this directory. Multiple subdirectories can also be created through this path. /tmp Directory to store temporary files. Data in this directory will be erased after reboot/power-off. Page 13 of 20 eH880 and ACR880 SDE Setup Manual Document Title Here Version 1.4 Document Title Here info@acs.com.hk www.acs.com.hk 5.2. Ethernet Connection 5.2.1. Device to PC Host PC (Windows) Figure 4: 5.2.2. eH880 Use the Cross-over Cable for PC Host to Device Setup. Device to Hub/ Switch to PC Host Linux Server (NFS Server) PC (Windows) Network Switch eH880 DHCP Server Figure 5: Use the Straight Cable for Device to Hub/Switch Setup Page 14 of 20 eH880 and ACR880 SDE Setup Manual Document Title Here Version 1.4 Document Title Here info@acs.com.hk www.acs.com.hk 5.3. Upload Types 5.3.1. ¾ ¾ FTP (File Transfer Protocol) "ftp" and "ncftp" are installed in the device User can login into the device and initiate FTP connection to a host computer; and user can use these two commands to transfer files. 5.3.2. SFTP (Secure FTP) ¾ An SFTP daemon is installed in the device. ¾ User can use an SFTP client to login (with above login info) the device and transfer files. 5.3.3. NFS (Network File Server) The eH880 supports mounting NFS filesystem and so it is able to mount folders from the remote NFS Severs for more convenient file transfer. NFS file server and Ethernet connection is required. NFS file server can be setup along with the development Linux PC Procedure: Login to the eh880 through telnet/sshIssue a command: mount -o nolock,rsize=1024,wsize= : /mnt/ext3 The files in the share directory will be appeared in /mnt/ext3 of the eh880 For details please refer to Annex A2 Page 15 of 20 eH880 and ACR880 SDE Setup Manual Document Title Here Version 1.4 Document Title Here info@acs.com.hk www.acs.com.hk Appendix A. Connecting eH880 to the Ethernet Network Appendix A.1. Configuring Ethernet Port Each eH880 Demo Unit has a built-in Ethernet port. The eH880 unit is pre-configured to get an IP from DHCP servers. After the demo program showed on the screen. Press F4 to view the IP address of the eH880. It is possible to change the IP manually After the telnet session has been established, an ‘ifconfig’ command to view the IP address assignment can be issued. The following is the example output when ifconfig is issued: ~ # ifconfig eth0 Link encap:Ethernet HWaddr 00:02:31:05:0A:01 inet addr:192.168.61.123 Bcast:192.168.61.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:110 errors:0 dropped:0 overruns:0 frame:0 TX packets:7 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:37 Base address:0x300 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) On the other hand, users can also configure network parameters. The following sections discuss the commands and procedures to do so. User can specifically choose either static IP or dynamic IP address configuration for the eH880 unit. However, note that such changes will not be permanent – after the device is re-booted again, its IP address will resume the saved setting in the eH880. To permanently change the IP address, please refer to eH880 tool manual. Appendix A.1.1. Setting up Loop Back Device Loop back device is used to refer to local host of the eH880 unit and it has a default IP address 127.0.0.1 with netmask 255.0.0.0. 1. Input the following command to bring up the loop back device interface: # ifconfig lo 127.0.0.1 2. Input “ifconfig” command to show the configuration: # ifconfig lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Page 16 of 20 eH880 and ACR880 SDE Setup Manual Document Title Here Version 1.4 Document Title Here info@acs.com.hk www.acs.com.hk 3. Input the following command to add an entry to routing table. # route add –net 127.0.0.0 netmask 255.0.0.0 lo 4. Input the “route” command to show the routing table. ~ # route Kernel IP routing table Destination Gateway 127.0.0.0 Genmask 255.0.0.0 Flags Metric Ref 0 lo Use Iface Appendix A.1.2. Setting Up Static IP Address Assume you want to setup the following IP address for eH880 unit: IP Address Subnet Mask Gateway 192.168.1.100 255.255.255.0 192.168.1.1 1. Input the following command to setup the IP address: # ifconfig eth0 192.168.1.100 netmask 255.255.255.0 2. Input the following command to setup the gateway: # route add default gw 192.168.1.1 eth0 3. Input “ifconfig” command to show the configuration: # ifconfig eth0 Link encap:Ethernet HWaddr 00:0B:51:00:0F:FE inet addr:192.168.1.100 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:10155 errors:0 dropped:0 overruns:0 frame:0 TX packets:22 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:37 Base address:0x300 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) 4. Input “route” command to show the routing table: # route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.1.0 * 255.255.255.0 U 0 0 eth0 127.0.0.0 255.0.0.0 U 0 0 lo default 192.168.1.1 0.0.0.0 UG 0 0 eth0 Page 17 of 20 eH880 and ACR880 SDE Setup Manual Document Title Here Version 1.4 Document Title Here info@acs.com.hk www.acs.com.hk Appendix A.1.3. Setting up Dynamic IP Address If it is necessary to setup the dynamic IP address for eH880 unit, input the following command to get the IP address from DHCP server: # udhcpc –b –i eth0 Appendix A.2. Setting up Network File System (NFS) Server Appendix A.2.1 PC Side The exported directories of NFS server are controlled by “/etc/exports” configuration file. To share the directory of Linux Server with eH880 unit, you need to edit the file. Sample contents of “/etc/exports” configuration file: /share1 192.168.1.0/24(ro) /share2 192.168.1.100(rw) For example, directory “/share1” can be shared by all devices with IP address starting with “192.168.1.xxx”. Note that “192.168.1.0” is network address and “24” is the short form of “255.255.255.0” subnet mask. “ro” is used to share directory for read-only while “rw” is used to share directory for read/write. Directory “/share2” is only shared to the device that has an IP address equal to “192.168.1.100” for read/write. After editing the configuration file, restart NFS server for the changes to take effect. Input the following command to restart NFS server: # /etc/rc.d/init.d/nfs restart Appendix A.2.2 eH880 side In the eH880 unit, you can input the following command to use remote directory that is shared by NFS server. Assume that the IP address of Linux server is “192.168.1.10”. # mount –o nolock,rsize=1024,wsize=1024 192.168.1.10:/share1 /mnt/ext1 You can change to directory “/mnt/ext1” by inputing “cd /mnt/ext1” command. Appendix A.2.3 NFS (Network File System) After logging in the device (telnet), user can mount a directory structure in his PC Linux to a directory in the device and then use "cp" command to copy files to another directory in the device. To mount a directory on the command prompt: "mount -o nolock,rsize=1024,wsize=1024 xxx.xxx.xxx.xxx:/home/user /mnt/ext1" "cp /mnt/ext1 /usr/local/rw" Page 18 of 20 eH880 and ACR880 SDE Setup Manual Document Title Here Version 1.4 Document Title Here info@acs.com.hk www.acs.com.hk User can also execute a program inside the mounted directory directly without implicit transfer. The mount command will "mirror" the directory /home/user in your PC Linux (with IP = xxx.xxx.xxx.xxx) to /mnt/ext1 in the eH880 Note that "1024" in the above example is necessary to ensure reliability when transferring big files. Note also that the NFS service in your PC Linux have to be configured correctly to open permission of the directory that is going to be mounted. See "man nfs" and "man exports" in PC Linux for detail. Appendix A.3. Showing the Status of Processes To show the status of processes, input “ps” (process status) command. The information is arranged by Process ID (PID), User ID (Uid), Virtual Memory Size in bytes (VmSize), Process State (Stat) and command line (Command). According to the man page of “ps” command, the process state has the following meanings: Process State ~ $ ps PID Uid 1 root 2 root 3 root 4 root 5 root 16 root 19 root 42 root 43 root 45 root 44 root 125 root 150 root 192 root 194 root 214 root 217 root 221 root 222 root 224 root 225 root 228 root 229 root 230 root Description uninterruptible sleep (usually IO) runnable (on run queue) Sleeping traced or stopped a defunct ("zombie") process Has no resident pages High-priority process Low-priority task Has pages locked into memory (for real-time and custom IO) VmSize Stat Command 576 S init SWN [ksoftirqd/0] SW< [events/0] SW< [khelper] SW< [kthread] SW< [kblockd/0] SW [khubd] SW [pdflush] SW [pdflush] SW< [aio/0] SW [kswapd0] SW [mtdblockd] SWN [jffs2_gcd_mtd4] 612 S syslogd 612 S klogd 636 S inetd 1428 S webs 396 S /usr/local/eH880/RW/bin/eH880_disc 832 S eH880_Demo4 752 S -sh 1360 S sshd -f /usr/local/eH880/RW/etc/ssh/sshd_config 832 S eH880_Demo4 832 S eH880_Demo4 832 S eH880_Demo4 Page 19 of 20 eH880 and ACR880 SDE Setup Manual Document Title Here Version 1.4 Document Title Here info@acs.com.hk www.acs.com.hk 233 root 234 root 235 root 236 root 237 root 238 root 248 root 252 root 253 root 254 root 257 root ~$ 832 S 832 S 832 S 832 S 832 S 832 S 580 S 512 S 480 S 752 S 664 R Appendix A.4. eH880_Demo4 eH880_Demo4 eH880_Demo4 eH880_Demo4 eH880_Demo4 eH880_Demo4 udhcpc -i eth0 -b more /usr/sbin/telnetd -sh ps Miscellaneous Information Appendix A.4.1 User ID and Password The unit is setup for the following user: User ID root Password cdy123 Hence, the user can login as root user to communicate with the eH880 unit. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Page 20 of 20 eH880 and ACR880 SDE Setup Manual Document Title Here Version 1.4 Document Title Here info@acs.com.hk www.acs.com.hk
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Encryption : Standard V2.3 (128-bit) User Access : Print, Extract, Print high-res Page Count : 20 XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:5559e5b3-eb68-4804-b6e2-2fab6146c56c Producer : Acrobat Distiller 8.0.0 (Windows) Create Date : 2009:12:31 17:35:38+08:00 Creator Tool : PScript5.dll Version 5.2 Modify Date : 2010:01:06 10:38:16-08:00 Metadata Date : 2010:01:06 10:38:16-08:00 Document ID : uuid:deee9f2b-0320-4b75-89ab-0e1395716e77 Instance ID : uuid:1ae22403-2ecb-40e2-b322-490a64e98ea3 Format : application/pdf Creator : a Title : Microsoft Word - eH880 and ACR880 SDE Setup Manual V1.4.doc Author : aEXIF Metadata provided by EXIF.tools