Advanced Mobile Payment AMP6500 AMP 6500 User Manual
Advanced Mobile Payment Inc. AMP 6500 Users Manual
Users Manual
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. 6500 Port cover SIM/SAM card cover 4 core Menu for setup Reset Tag label Jan 2018 Infrared LED NFC leds RF exposure information: The EIRP power of the device at maximal case is below the exemt condition, 20mW specified in EN62479: 2010. RF exposure assessment has been performed to prove that this unit will not generate the harmful EM emission above the reference level as specified in EC Council Recommendation(1999/519/EC). Camera USB - host Infrared sensor 6500-CB USB-device LCD RS232 Magnetic stripe card Ethernet Antenna inductive zone 6500 Audio Waterproof ring The Microfit cable MDB User smart card slot 6500 6500 High Performance 4 Core Processor + Secure CPU 1GB RAM, 8GB Flash memory, Support Micro TF Card, up to 32GB 5”, 720x1280 pixels, support capacitate touch screen RS-232, Ethernet 10/100M, MDB PCI PTS 5.X, EMV LEVEL 1&2, EMV Contactless, CE, FCC, Pay Pass 1 SAM, 1 TF card reader, MDB interface, Mircrofit port, proximity detector 12V DC, 2A (when using Micro fit), 24 ~ 45V DC (when using MDB) (195x122x94mm)-(7.7x4.8x3.7’’)LxWxH SAM 1 key for reset, 1 key for setup Android OS 5.X 720g(1.6lbs) 2. Avoiding the direct sunlight and the rain. 3. Place the device in a ventilated locality and keep good a heat dissipation condition. SIM Microfit power or MDB power jack 6500 -20℃ ~ 45℃(-4℉~ 113℉), 10% ~ 90% (non-condense) TF 1. The device should be covered by a pin shield over the pin entry area. -25℃ ~ 75℃(-13℉~167℉), 0% ~ 95% (non-condense) WATERPROOF IP65 PROTECTION IK08 MODULATION NFC 13.56MHz 6500 Microfit
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 1 Create Date : D:20180425030205Z Modify Date : D:20180425030205Z Producer : Corel PDF Engine Version 14.0.0.653 Author : Administrator Creator : CorelDRAW Title : 5310英文说明书-AMP达培明.cdrEXIF Metadata provided by EXIF.tools