Advantech Co TREK550A2 Computer User Manual TREK 550 A2 user manaul 0829
Advantech Co Ltd Computer TREK 550 A2 user manaul 0829
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2058941 |
| Application ID | s8zTfGePItRJYNiIVXHRkA== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 217.28kB (2716054 bits) |
| Date Submitted | 2013-08-30 00:00:00 |
| Date Available | 2013-08-30 00:00:00 |
| Creation Date | 2013-08-29 14:24:09 |
| Producing Software | Acrobat Distiller 6.0 (Windows) |
| Document Lastmod | 2013-08-30 11:23:34 |
| Document Title | TREK-550 A2 user manaul -0829.pdf |
| Document Creator | PScript5.dll Version 5.2 |
| Document Author: | USER |
User Manual
TREK-550
Computing Box
Copyright
The documentation and the softwareincluded with thisproductarecopyrighted2010by
Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to
make improvements in the products described in this manual at any time without
notice. No part of this manual may be reproduced, copied, translated or transmittedin
any form or by any means without the prior written permission of Advantech Co.,Ltd.
Information provided in this manual is intended to be accurate andreliable. How-ever,
Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringements of
the rights of third parties, which may result from its use.
Acknowledgements
Intel and Atom are trademarks of Intel Corporation.Microsoft Windowsand
MS-DOS are registered trademarks of Microsoft Corp.All other product names or
trademarks areproperties of their respective owners.
Product Warranty (2 years)
Advantech warrants to you, the original purchaser, that each of itsproducts will befree
from defects in materials and workmanship for two years from the date of purchase.
This warranty does not apply to any products which have been repaired or altered by
persons other than repair personnel authorized by Advantech, or which have been
subject to misuse, abuse, accident or improper installation. Advantech assumes no
liability under the terms of this warranty as a consequence of such events.
Because of Advantech’s high quality-control standards and rigorous testing, most of
our customers never need to useour repair service. Ifan Advantechproduct is defective,
it will be repaired or replaced at no charge during the warranty period. For out-
of-warranty repairs, you will be billed according to the cost of replacement materials,
service timeand freight.Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. (For example, CPU
speed, Advantech products used, other hardware and software used, etc.) Note
anything abnormal and list any onscreen messages you get when the problem
occurs.
2. Call your dealer and describe theproblem. Pleasehaveyour manual, product,
and any helpful information readilyavailable.
3. If your product is diagnosed as defective, obtain an RMA (return merchandise
authorization) number from your dealer. This allows us to process your return
more quickly.
4. Carefully pack the defective product, a fully-completed Repair and Replacement
Order Cardandaphotocopy proof ofpurchase date (suchasyour sales receipt)in
a shippable container. A product returnedwithoutproof of the purchase dateis not
eligible for warranty service.
5. Writethe RMAnumbervisibly on the outside of thepackageand ship it prepaidto
your dealer.
TREK-550 User Manual
Part No. 2010055001
Edition 1
Printed inTaiwan
May 2010
ii
Declaration of Conformity
This product has passed the CE test for environmental specifications. Test conditions
for passing included the equipment being operated within an industrial enclosure. In
order to protect the product from being damaged by ESD (Electrostatic Discharge)
and EMI leakage, we strongly recommend the use of CE-compliant industrial
enclosure products.
FCC Class B
Note: Thisequipment has been tested and found to comply with the limits for a ClassB
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not
installedand usedinaccordance with the instructions, maycause harmful interference
to radiocommunications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one ormore of the
following measures:
Reorient or relocate the receiving antenna.
!
Increase the separation between theequipment and receiver.
!
Connecttheequipment into anoutlet on acircuit different from that to which the
!
receiver is connected.
Consult the dealer or an experiencedradio/TV technician for help.
!
FM
This equipment has passed the FM certification. According to the National Fire
Protection Association, work sites are classified intodifferent classes, divisionsand
groups, based on hazard considerations. This equipment is compliant with the
specifications of Class I, Division 2, Groups A, B, C andD indoor hazards.
Technical Support and Assistance
1.
2.
Visit the Advantech web site at www.advantech.com/supportfor the latest
information about the product.
Contact the distributor, sales representative, or Advantech's customer service
center for technical support if you need additional assistance. Please have the
following information ready before you call:
– Product name and serial number
– Description of yourperipheralattachments
– Description of your software (operatingsystem, version, application software,
etc.)
– A complete description of the problem
– The exact wording of any error messages
iii
TREK-550 User Manual
Warnings, Cautions and Notes
Warning! Warnings indicate conditions, whichifnotobserved, can cause personal
Injury!
Caution! Cautions are included to help you avoid damaging hardware or losing
data. e.g.
There isa danger of anew battery exploding if itis incorrectly installed.Do
notattempt to recharge, force open,or heat the battery. Replacethebattery
only with the same or equivalent type recommended by the manufacturer.
Discard used batteriesaccording to the manufacturer'sinstructions.
Note!
Notes provide optional additionalinformation.
Document Feedback
Toassist us in makingimprovementsto thismanual,we would welcome comments
and constructive criticism. Send allsuch in writing to: support@advantech.com
Packing List
Before setting up, check that the itemslistedbelow are included, ingood condition. If
any item does not accordwith the table, please contact your dealerimmediately.
TREK-550 series Computing Box
!
!
Accessories for TREK-550
!
Warranty card
!
Power cord: DC power inlet cable(180 cm - for TREK-550 only)
!
Videio in/CAN cable
!
“Drivers, Utilities and User Manual" CD-ROM
!
End User License Agreement (XPE and WinCE model)
Ordering information
Safety Instructions
1.
2.
3.
Read these safety instructions carefully.
Keep this User Manual for later reference.
Disconnect thisequipment fromany AC outlet before cleaning. Use a damp
cloth. Do not use liquid or spray detergents for cleaning.
4. For plug-in equipment, the power outlet socket must be located nearthe
equipment and must be easily accessible.
5. Keep this equipment awayfrom humidity.
6. Put this equipment on a reliable surface during installation.Dropping it or lettingit
fall maycausedamage.
7. Theopeningson the enclosure are for air convection. Protect the equipment
from overheating. DO NOT COVER THE OPENINGS.
8. Make sure the voltage ofthe powersource is correctbeforeconnecting the
equipment to the poweroutlet.
9. Position the power cord so that peoplecannot step on it. Do not place anything
over the power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the power sourceto
avoid damage by transient overvoltage.
12. Never pour any liquid into an opening. Thismay cause fire or electrical shock.
13. Never openthe equipment. For safety reasons, the equipment shouldbe
opened only by qualified servicepersonnel.
14. If one of the following situations arises, get the equipment checkedby service
personnel:
15. Thepower cord or plug is damaged.
16. Liquidhas penetrated into theequipment.
17. Theequipment has been exposed to moisture.
18. The equipment does not work well,or you cannot get it to work according to the
user's manual.
19. Theequipment has been dropped and damaged.
20. The equipment has obvious signs of breakage.
21. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE
TEMPERATURE MAY GO BELOW -30° C (-22° F) OR ABOVE 70° C
(158° F). THIS COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT SHOULD
BE IN A CONTROLLED ENVIRONMENT.
Operating temperature: 50° C
22. CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY
REPLACED. REPLACE ONLYWITH THE SAME OR EQUIVALENT TYPE
RECOMMENDED BY THE MANUFACTURER, DISCARD USEDBATTERIES
ACCORDING TO THE MANUFACTURER'S INSTRUCTIONS.
23. Thesound pressure levelat theoperator's position according to IEC 704-1:1982
is no more than 70dB (A).
DISCLAIMER: This set of instructionsis given according to IEC 704-1. Advantech
disclaims all responsibility for the accuracy of anystatements contained herein.
v
TREK-550 User Manual
Wichtige Sicherheishinweise
1.
2.
3.
Bitte lesen sie Sich diese Hinweisesorgfältig durch.
Heben Sie diese Anleitung für den späteren Gebrauchauf.
Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden Sie
Keine Flüssig-oder Aerosolreiniger. Am besten dient ein angefeuchtetes Tuch
zur Reinigung.
4. Die NetzanschluBsteckdose soll nahe dem Gerät angebracht und leicht
zugänglich sein.
5. Das Gerät ist vor Feuchtigkeit zuschützen.
6. Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten. Ein Kippen
oder Fallen könnte Verletzungen hervorrufen.
7. Die Belüftungsöffnungen dienenzur Luftzirkulation die das Gerät vor überhit-
zung schützt. Sorgen Sie dafür, daB diese Öffnungen nicht abgedeckt werden.
8. Beachten Sie beim. AnschluB andas Stromnetz die AnschluBwerte.
9. Verlegen Sie die NetzanschluBleitung so, daB niemand darüber fallen kann. Es
sollte auch nichts auf der Leitung abgestellt werden.
10. Alle Hinweise und Warnungen diesich am Geräten befinden sind zu beachten.
11. Wird das Gerät über einen längeren Zeitraum nicht benutzt, sollten Sie es vom
Stromnetz trennen. Somit wird im Falle einer Überspannung eine Beschädigung
vermieden.
12. Durch dieLüftungsöffnungen dürfen niemalsGegenstände oder Flüssigkeitenin
das Gerätgelangen. Dies könnte einen Brand bzw. elektrischen Schlag aus-
lösen.
13. Öffnen Sie niemals das Gerät. Das Gerät darf aus Gründen der elektrischen
Sicherheit nur von authorisiertem Servicepersonal geöffnet werden.
14. Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz zutrennen
und von einer qualifizierten Servicestelle zu überprüfen:
15. Netzkabel oder Netzstecker sind beschädigt.
16. Flüssigkeit ist in das Gerät eingedrungen.
17. Das Gerät war Feuchtigkeit ausgesetzt.
18. Wenn dasGerät nicht derBedienungsanleitungentsprechend funktioniert oder
Sie mit Hilfe dieser Anleitung keineVerbesserung erzielen.
19. Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt.
20. Wenn dasGerät deutliche Anzeichen einesDefektes aufweist.
21. VOSICHT: Explisionsgefahr bei unsachgemaben Austausch der Batterie.Ersatz
nur durch densellben order einem vom Hersteller empfohlene-mahnlichen Typ.
Entsorgung gebrauchter Batterien navh Angaben des Herstellers.
22. ACHTUNG: Es besteht die Explosionsgefahr, falls die Batterie auf nicht fach-
männischeWeise gewechselt wird.Verfangen Sie die Batterienur gleicheroder
entsprechender Type, wievom Hersteller empfohlen. Entsorgen Sie Batterien
nach Anweisung des Herstellers.
23. Der arbeitsplatzbezogene Schalldruckpegel nach DIN45 635 Teil 1000 beträgt
70dB(A) oder weiger.
Haftungsausschluss: Die Bedienungsanleitungen wurden entsprechend der
IEC704-1 erstellt. Advantech lehnt jegliche Verantwortung für die Richtigkeit
der indiesem Zusammenhang getätigten Aussagen ab.
TREK-550 User Manual
vi
Safety Precaution - Static Electricity
Follow these simple precautions to protectyourselffrom harm and the products from
damage.
To avoid electrical shock, always disconnect the power from your PC chassis
!
before you work on it. Don't touch any components on the CPU card or other
cards while the PC is on.
Disconnect power before making any configuration changes. The sudden rushof
!
power as you connect a jumper or installa card may damage sensitive electronic
components.
Warning! 1. Input voltage rated: 9-36 Vdc.
2. Transport: carrythe unit withboth hands and handle with care.
3. Maintenance:toproperly maintain and cleanthesurfaces, use only
approved products orclean witha dry applicator.
4. CompactFlash:Turn off the power before inserting or removing
CompactFlash storage cards.
ropean Contact information:
Advantech Europe GmbH
Kolberger Straße 7
D-40599 Düsseldorf, Germany
Tel: 49-211-97477350
Fax: 49-211-97477300
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not
cause harmful interference and (2) this device must accept any interference received, including interference that may cause
undesired operation. “Complies with CANADA RSS-210
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment
into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV
technician for help.
b. FCC Part 15.21 information for user
You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your
authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not
cause harmful interference and (2) this device must accept any interference received, including interference that may cause
undesired operation
Notes and Warnings to the User and Installer: Caution:
This Installation Guide is intended for use by the professional wireless LAN system installer.
The device cannot be sold retail, to the general public or by mail order. It must be sold to dealers or have strict marketing control.
Who Should Use this Guide:
Installation of this device should be accomplished only by a qualified wireless LAN system installer who is: -Knowledgeable of the
use, installation and configuration procedures and associated networking components.
-Knowledgeable of each system component’s equipment User and Installation Guide.
-Knowledgeable of the installation and configuration procedures for the site’s network infrastructure system and wiring.
-Knowledgeable of the installation procedures, safety, and code requirements for the site’s antenna, antenna mast,
antenna cabling, and installation.
We highly recommend that the antenna installation be performed by a qualified antenna installation professional.
Users should not attempt to make such connections themselves, but should contact the appropriate electrical inspection authority,
or electrician, as appropriate.
Only the approved antenna types may be used with this transmitter
FCC RF Radiation Exposure Statement:
1.This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
2.This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
Contents
Contentsix
Chapter 1
1.1
1.2
1.3
1.4
Chapter 2
2.1
2.2
2.3
2.4
2.5
2.6
General Information............................1
Introduction...............................................................................................2
General Specifications..............................................................................2
1.2.1 General.........................................................................................2
1.2.2 Standard PCFunctions.................................................................3
1.2.3 PCIBus Ethernet Interface...........................................................3
1.2.4 Touchscreen.................................................................................3
1.2.5 Environment..................................................................................4
LCD Specifications....................................................................................4
Table 1.1: LCD Specifications.....................................................4
Dimensions...............................................................................................4
Figure 1.1 TREK-550 dimensions................................................4
System Setup.......................................5
A Quick Tour of the Mounted.......................................................6
Figure 2.1 Front viewof theTREK-550.......................................6
Figure 2.2 Left side of the TREK-550..........................................6
Figure 2.3 Rear view of the TREK-550........................................7
Figure 2.4 Computing BoxI/O...................................7
Installation Procedures..............................................................................8
2.2.1 Connectingthe Power Cord..........................................................8
Table2.1: Pin Definitionof Power Cord......................................8
2.2.2 Connecting theKeyboard orMouse.............................................8
2.2.3 Switchingon the Power................................................................8
Running the BIOSSetup Program............................................................9
Installing System Software........................................................................9
Installing the Drivers................................................................................10
Programming FunctionKeysand GPIO/CAN BUS.................................10
ix
TREK-550 User Manual
Chapter 4
4.1
4.2
4.3
4.4
Chapter 5
A.1
A.2
A.3
A.4
A.5
Jumper Settings and Connectors...19
Setting Jumpers and Switches................................................................20
4.1.1 Locating Jumpers and Switches.................................................20
Table 4.1: Jumpers& LEDS on theMotherboard.....................20
4.1.2 Locating Jumpers and LEDs on the Motherboard......................21
Figure 4.1 Locating Jumpers /LEDs.........................................21
4.1.3 Connectorson the Motherboard.................................................22
Table 4.2: Connectorson the Motherboard...............................22
4.1.4 Locating Connectors ontheMotherboard..................................23
Figure 4.2 Locating Connectors onthefront side......................23
Figure 4.3 Locating Connectors onthebackside.....................23
CPU Installation......................................................................................24
Jumper Settings......................................................................................24
4.3.1 CMOS Clear for ExternalRTC (JP1)..........................................24
Table 4.3: Clear CMOS /External RTC (JP1)...........................24
4.3.2 Power FeatureSetting (JP3)......................................................24
Table 4.4: Ignition InputSwitchSetting (JP3)...........................24
Table 4.5: Power off/ Hard off Delay Setting (JP3)..................25
Table 4.6: Low Battery Monitor (JP3)........................................26
COM Port Interface.................................................................................27
Table 4.7: SerialPort DefaultSettings......................................27
4.4.1 COM Port Pin 9 Power OutputSetting(CN27)...........................28
Table 4.8: COMPort Pin 9 PowerOutput Setting (CN27)........28
4.4.2 COM Port Pin 9 Power OutputValue Setting(JP2)....................28
Table 4.9: COMPort Pin 9 PowerOutput Value Setting (JP2).28
Pin Assignments...............................43
InternalSpeaker Connector (CN2 onPCM-028)....................................44
TableA.1: Internal SpeakerConnector (CN2 on PCM-028)......44
COM1, 2 (CN17,19)................................................................................44
TableA.2: COM1, 2 (CN17,19)..................................................44
GPIO/ CAN BUS Connector(CN31)......................................................45
Table A.3: GPIO/ CAN BUSConnector(CN31).......................45
Inverter/ Touch/ USB Connector(CN18)..............................................46
Table A.4: Inverter/ Touch/ USB Connector (CN18)................46
Power Inlet..............................................................................................47
Table A.5: Power inlet................................................................47
Chapter 6
SW demo application set Up...............43
A.1
J1939/CAN……………………………………………....................................44
TableA.1: ............. ................................ ................................44
RTC.......................................................................... ...............................44
TableA.2:................................................ .................................44
Power management ........................... .....................................................45
Table A.3: GPIO/ CAN BUSConnector(CN31).......................45
GPIO .......................................... ..........................................................46
Video ................ .......................................................................................44
TableA.2: ......... ........................................................................44
Dead reckoning................ .....................................................................45
Table A.3: ..............................................................................45
G-sensor ...............................................................................................46
A.2
A.3
A.4
A.5
A.6
A.7
AppendixA
B.1
B.2
TREK-303.....................................49
TREK-303 spec ........................................................................50
B.1.1 .............................................................50
Other Information....................................................................................65
xi
TREK-550 User Manual
Chapter
1
General Information
This chapter gives background
information on the TREK-550
Computing Box.
Sections include:
! Introduction
! General Specifications
! Dimensions
1.1 Introduction
The TREK-550 is a dedicated box computer for industrial, transport trucks, buses and
taxis. TREK-550 combined with variety of I/O connectors can be connected to
devices like OBD-II or TPMS (Tire Pressure Monitoring System). Dual display/dual
audio interfaces supporting different resolutions can deliver different applications to
different displays; eg: one application to a driver and another to a digital signage
application.
Built-in wireless communications (WWAN, WLAN, ) enable TREK-550 to send
important driver/ location/cargo information back to the control center. TREK-550 can
also operate in extreme environments with features like a wide working temperature
range (-30 to 70 degrees). TREK-550 also uses a special design to handle the critical
issue of in power. Special power protection (ISO7637-2/SAE J1455 Class A/ SAE
J1113) and power management software (Ignition on/off, delay on/off, low battery
monitor) prevent electrical noise and surges from impacting the system, guarding
against damage from transient power. TREK-550 also support rear view monitor
through connecting video in port. With this feature, driver can real time monitor the
environment on two sides of the truck for driving safety. TREK-550 can also support
dead-reckoning feature, which means the truck can still be traced even the driver is
driving in a tunnel.
Rear-Side Connectors
1.2 General Specifications
Key features
Supports Win CE 6.0, XPE, XP and Linux
Automotive grade working temperature range (-30° C to 70° C)
Rich I/O including CAN, LAN, RS-232, RS-485, J1708, isolation 4DI/4DO, Line out,
Mic in, USB, and Video-in
Built-in communication modules, including GSM/GPRS/HSDPA/CDMA, WLAN
GPS with AGPS and dead reckoning technology (Gyro & speed line)
Certifications: CE/FCC/e-mark, MIL-SD810F, ISO 7637-2, SAE J1455, SAE J1113
regulations
Dual display/audio output for both driver and passenger
Ignition on/off delay; SW detectable/controllable for power management
1.2.1 General
!
!
!
Dimensions: (W x H x D): 271 x 149 x 69.7 mm.
Weight: 2 kg.
Power supply:
– Input voltage: 6~ 36Vdc, support ignition cold crank
– Ignition on/off
– Low battery shut-down protection threshold(optional): When the battery
voltage leveldrops below 11V for more than 30 seconds, TREK-550will
automatically shut down in order to prevent “deep discharge” situationsand
TREK-550 can be re-activated only when the voltage is > 11V.
– Power on delay:Default 2 seconds. Whenthe TREK-550 is powered on via
ignition key, the system willdelay 2seconds to poweron.
– Power off delay: Default 5 seconds. When TREK-550 power is controlled by
ignition key and turns off by the key (ignition=off), the TREK-550 will start the
shut procedure after 5seconds.
– Hard offdelay: Default30seconds. When TREK-550 poweris controlledby
ignition key and turns off by the key (ignition=off), the TREK-550 will cut offthe
5VSB power after 30 seconds. Inthis event when the shutdown processis
longer than 30 seconds, the power will be shut down hard,turning off the
TREK-550's powerand 5VSB.
Note!
!
!
!
For more detail of function pleaserefer toChapter 4, Section 4.3.2 of
this manual.
Power consumption: The maximum current consumption is about 32.4 watts.
The power consumption is 12 watts in normal mode (with only XPE running; no
I/O device and modules connected tothe TREK-550).
Front panel and back cover: IP65 Sealed; NEMA4 compliant
(Not including the I/O ports).
Enclosure: Ruggedized aluminum without ventilationholes.
1.2.2 Standard PC Functions
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
CPU: Intel Atom Z510PT 1.1Ghz/ Z520PT 1.3Ghz
Chipset: Integrated in LE82US15EE
BIOS: Award 256KB Flash BIOS, ACPI 2.0Compliant.
System chipset:.
System memory:One 200-pin SODIMMsockets, accepts up to2GB DDR667
DDR
Solid state disk: Supports one 50-pin socketfor Compact-Flash type I/II (True
PATA mode).
Serial ports: Two RS-232, 5V@500mA,12V@ 250mA, ping9, by jumper selected.
One 4-wire RS232,1 x RS485, 1 x J1708 ports.
Universal serial bus (USB) port: Supports up to three USB2.0. One from smart
display port.
LAN port: 1 x 10/100/1000 Ethernet (with LEDs) by RJ45.
Video output: 1 x VGA output by DB-15 (independent display).
Video in: 2 x composite video input selection supported format (for rear view
monitor) by RJ-45 connector
Mini PCI express bus expansion slot: Accepts half size mini PCI bus card.
Watchdog timer: 63-level timerintervals automaticallygenerate system reset
when the system stopsdue to a program error or EMI. Jumper selectionand
software enabled/disabled.
RTC Battery: 3.0 V @ 195mA lithium battery.
Power management: Supports power savingmodes including Normal/
Standby/Suspend modes.APM 1.2 compliant.
Digital I/O:Opticallyisolated 4 digital input and 4 digital output
CAN bus: RS-232 baud rate up to 115.2K bps.
Audio controller: AC97 Ver. 2.0compliant interface, Multi stream
Direct sound and Direct Sound 3D acceleration.
Stereo sound: 18-bit full-duplex codec.
Audio interface: One 2W speaker, onemicrophone. One line out.
Optional modules: 12channels GPS, quad-bandGSM/GPRS, MiniPCIWLAN
card.
1.2.3 PCI Bus Ethernet Interface
!
!
!
Chipset: Realtek RTL8100CL PCI local bus Ethernet controller.
Ethernet interface: Fullcompliance with IEEE 802.3u 100Base-T and 10 Base-T
specifications. Includessoftware drivers and boot ROM that supports bothRPL
andPXE.
100/10Base-T auto-sensing capability.
1.2.4 Touchscreen
!
!
!
!
!
!
Type: Analog Resistive
Light transmission: 80%
Controller: RS-232interface
Power consumption: <5.5 V@ 20 mA
Durability: > 10 million depressions
Software driver: Supports Windows XP/XP Embedded, WinCE
1.2.5 Environment
!
!
!
!
High/low temperature: -30 ~ 70° C
Relative humidity:10 ~ 95% @ 40° C (non-condensing)
Shock: 30 G peak acceleration (11 msec duration)
Certifications: CE, FCC, CCC, Emark, CB.
Vibration: 5 ~ 500 Hz SAE J1455 4.9.4.2, MIL-STD-810F 514.5
1.4 Dimensions
Figure 1.1TREK-550 dimensions
TREK-550 User Manual
Chapter
Syst
System Setup
This chapter details system setup
on TREK-550.
Sections include:
!A Quick Tour of the computer box
!Installation Procedures
!Running the BIOS Setup
Program
2.1 A Quick Tour of the TREK-550 Computing box.
Beforestarting to set up the Computing Box,takeamomentto becomefamiliar with the locations
andpurposes of the controls,drives, connectors and ports,which are illustratedinthe figures
below. When theComputerboxisplaced inside truck glove cabinet or under the passenger’s seat
next to the driver, its front appears as showninFigure 2.1.
Figure 2.1. front view of TREK-550
Figure 2.1.fdasdf
Figure 2.2. Rear view of TREK-550
Unit: mm
Figure 2.3. Side view of TREK-550
Unit: mm
Figure 2.4. Bottom view of TREK-550
Unit: mm
Figure 2.5. Top view of TREK-550
2.2 Installation Procedures
2.2.1 Connecting the Power Cord
Connect the three pin waterproof power cord to the DC inlet of the Computing Box.
On theopen-wire end, one pin is reserved for positive voltage and ismarked,
"+"; one pin is reserved for ground and is marked, "-"; and, one pin is
reserved for the ignition signal with an “ignition” mark.
Note!
Power on/off theTREK-550 via the TREK-550's power switch. Please
connect its"+ "and" ignition"pins together with the powersource's
"+".
Or change theJP3 jumper setting.(For JP3 jumper settingplease
seesection 4.3.2.1)
Note! Ignitionon/offsetting : The TREK-550 supports an ignition on/off
func-tion so that you can power on/off the TREK-550 via the ignition
signal/
voltage. Either connect the TREK-550's "ignition" pin to ignitionand
the TREK-550 "+-"to "+-" ; or connect the TREK-550's "ignition &
+" pins togetherwith powersource's"+" , and"-" to "-". Pleasealso
setthe "power on after powerfailure” function to "always on" in
BIOS.(forBIOS settings, please see Appendix D). The delay on/off
will be activeonce theignitionon/off is selected.
Table 2.1: Pin Definition of Power Cord
Pin
Definition
Color
1
+
yellow
3 - black
4
Ignition
white
Power Connector
Molex Manufacturer part no. 0430451200
Power Connector
Pin
Signal
Pin
Signal
Chassis Ground
Ground
Ground
(Reserved)
(Reserved)
(Reserved)
Power Input (6~36 VDC)
Power Input (6~36 VDC)
Acc Ignition Input
10
Ground
11
(Reserved)
12
Power Button Input
Mating power cable
Advantech p/n : 1700018306 A Cable 2*6P-3.0/fuse 180cm TREK
Manufacturer p/n: Best Technology Enterprise 900-1200-180R
2.3 Running the BIOS Setup Program
In most cases, the computer will have been properly set up and configured by the
dealer or SI prior to delivery. However, it may still be necessary to adjust some of the
computer's BIOS (Basic Input-Output System) setup programs to change the system
configuration data, like the current date and time, or the specific type of hard drive
currently installed.
The setup program is stored in read-only memory (ROM). It can be accessed either
when turning on or resetting the computer, by pressing the “Del” key on the keyboard
immediately after powering up thecomputer.
The settingsthatarespecifiedwiththesetup program are recorded in a specialareaof
the memory called CMOS RAM. This memory is backed up by a battery so that itwill
not be erased when turning off or resetting the system. Whenever the power isturned
on, the system reads the settings stored in CMOS RAM and compares them to the
equipment check conducted duringthe “power onself-test” (POST).If anerroroccurs,
an error message is displayed on screen, and the user is prompted to run the setup
program.
2.4 Installing System Software
Recent releases of operating systems from majorvendors includesetup programs
which load automatically and guide users through the entire process of operating
system installation. The guidelines belowhelp to determine the steps necessary to
install your operating system onthe computer hard drive.
Note!
Some distributors and system integrators may have already pre-
installed system software prior to shipment of your Mounted
Computer.
The BIOS of the computer supports system boots-up directly from the CD-ROM drive
whenever it is connected using a USB interface. Insert the system installation CD-
ROMinto the CD-ROMdrive.
Power on the computer, or reset the system by pressing the “Ctrl” + “Alt” + “Del” keys
simultaneously. The computer will automatically load the operating system from the
diskette or CD-ROM.
When presented with the opening screen of a setup / installation program, simply fol-
low the onscreeninstructions. Thesetup program guidesusersthrough preparationsof
thehard drive, and installation of the operatingsystem.
When presented with an operating system command prompt, like, A:\>, then it is nec-
essary to partition and format the hard drive, and manually copy the operating sys-
tem files to it. Refer to the operating system user instructions about partitioning and
formatting the hard drive.
2.5
Installing the Drivers
After installing system software, the computer is ready to set up the AMD chipset,
VGA, audio, LAN, and touch screen functions. All the pre-requisite drivers are stored
on a CD-ROM disc entitled “Drivers and Utilities” (Check the correct wording on the
CD, which can be found in theaccessory box.)
The utility directory includes multimedia programs. Some drivers and utilities in the
CD-ROM disc have their own text files which help users install the drivers and under-
stand their functions.
These files are a very useful supplement to the informationin this manual.For more
details of driver installation please refers to Chapter 5 to 10 of this manual.
Note!
The drivers and utilities used for the TREK-550 are subject to change
without notice. If in doubt, checkAdvantech'swebsite or contact our
application engineers for the latest informationregarding drivers and
utilities.
2.6 Programming Function Keys and GPIO/CAN
BUS
The Mount Computer provides five function keys, GPIO and CAN bus asshown in
section 2.1. These functions must be activated with the correct software,that’s why we
provide an AP library for customers to design their own software. Referto Appendix C
for more detail.
Chapter
Jumper Settings and
Connectors
4
This chapter explains how to set
up the Computing Boxhardware,
including instructionson setting
jumpers and connect-ing
peripherals, and how to set
switches and read indicators.
Be sure to read all the safety pre-
cautions before beginning the
installation procedure.
Sections include:
!Setting Jumpers
4.1 Setting Jumpers and Switches
It is possible to configure the Computing Box to match the needs of theapplication by
resetting the jumpers. A jumperis the simplestkindof electrical switch.It consists of two
metalpinsand a small metal clip, often protected by aplastic coverthat slides over the
pins to connect them. To “close” a jumper, connect the pins withthe clip. To “open” a
jumper, remove the clip. Sometimes a jumper has three pins,labeled 1, 2, and 3. In
this case, connecteither pins 1 and 2, orpins 2 and 3.
open
closed
closed 2-3
open
closed
closed 2-3
A pair of needle-nose pliers may be helpful when working with jumpers. If there are
any doubts about the best hardware configuration for the application, contact the
local distributor or sales representative before making any changes.
An arrow isused on the motherboard to indicate the first pin of each jumper.
TREK-550 User Manual
20
4.1.1 Locations of the Jumpers and Connector
SW1
JP1
CN2
CN4
BH1
JP3
JP2
Figure 4.1 Locations of jumpers and connectors on top side the motherboard.
SODIMM1
CN16
Figure 4.2 Locations of jumpers and connectors on bottom side of the motherboard.
TREK-550 User Manual
21
The figures below show the locations of the jumpers and connectors on daughter board used in TREK-550.
J2
J3
SW1
CN11
CN12
CN13
CN14
CN15
Figure 4.4 Locations of jumpers and connectors on bottom side of the daughter board.
4.1.2 Jumpers
Table 4.1: Jumpers on motherboard
Location
Function
JP1
input voltage selection
JP2
CMOS clear for external RTC
JP3
Pin9 of COM3 function selection
Table 4.2: Jumpers on daughter board
Location
Function
J2
CAN bus termination selection
J3
Pin9 of COM8 function selection
SW2
DI/GPS Function selection
TREK-550 User Manual
22
4.1.3 Connectors
On-board connectors link the Computing Box to external devices such ashard disk drives.
The table below lists the function of eachconnector.
Table 4.1: Connectors on motherboard
Location
Function
SW1
RESET
CN2
USB connector
CN4
CF connector
CN10
LAN connector
CN11
USB connector
CN12
Power input connector
CN13
Smart Display Connector
CN14
RS-232 connector (COM3)
CN15
VGA connector
CN16
Mini-PCIe Socket (USB + PCIe interface)
BH1
RTC battery
SODIMM1
SODIMM connector for DDR2 SDRAM
Table 4.2: Connectors on daughter board
Label
Function
CN1
RS-232 connector
CN2
4-wire RS-232 + RS-485 + RS-1708 connector
CN3
Isolated Digital I/O connector
CN4
Line-Out phone jack
CN5
Mic-In phone jack
CN8
Video-In and CAN bus connector
CN11
WWAN module connector
CN13
Mini-PCIe Socket (USB interface, for WWAN module)
CN14
GPS module connector
CN15
SIM holder
TREK-550 User Manual
23
4.3 Jumper Settings
4.3.1 CMOS Clear for External RTC (JP2)
Warning! 1. To avoid damaging the computer, always turn offthe power supply
before setting “Clear CMOS.”
2. Set the jumper back to “Normal Operation” before turning on the
power supply!
Table 4.3: Clear CMOS / External RTC (JP1)
Normal Operation (Default)
1
Clear CMOS
2 3
1
2 3
4.3.2 Power Input Voltage Setting (JP1)
TREK-550 must be configured properly according the power input range.
Table 4.4: Power Input Voltage Selection (JP1)
12VInput (Default)
1
24V Input
2 3
1
2 3
4.3.3 Pin 9 of COM3 Function Selection (JP3)
Pin 9 on COM3 port can be configured as RI, 5V or 12V output.
Table 4.7: Pin 9 of COM3 Function Selection (JP3)
RI
+5VDC (max. 500mA)
+12VDC (max. 250mA)
4.3.4 Pin 9 of COM8 Function Selection (J3)
Pin 9 on COM8 port can be configured as RI, 5V or 12V output.
Table 4.7: Pin 9 of COM8 Function Selection (J3)
RI
TREK-550 User Manual
+5VDC (max. 500mA)
+12VDC (max. 250mA)
24
4.3.5 DI/GPS Function Selection (SW2)
If the GPS module with Dead Reckoning function is used, the digital inputs 3/4 will be
used as inputs of GPS module. DIP switch (SW2) is used to select the function on DI 3/4
(Digital Input 3/4).
Table 4.7: Pin 9 of COM8 Function Selection (J3)
Digital Input
GPS (for Dead-Reckoning)
SW2.1
OFF
ON
SW2.2
ON
OFF
SW2.3
OFF
ON
SW2.4
ON
OFF
TREK-550 User Manual
26
4.4 COM Port Interface
The computer providestotally ten serialports for difference uses. Six of ten serial ports
(COM1~COM6) are implemented with Super I/O chip and their physical address are
fixed. And the other four serial ports are done by a USB serial converter, and need driver
support to work. In Advantech provided WES (Windows Embedded Standard) and Win
CE 6.0 OS, the four USB-to-Serial serial ports are fixed from COM8 to COM11).
Table 4.7: Serial Port Function
Port
Function
COM1
2-wire RS-232 (TXD/RXD) for TREK-303
COM2
3-wire RS-232 (TXD/RXD/RTS) for Touch on TREK-303
COM3
Full functional RS-232
COM4
For power management control
COM5
RS-485
COM6
J1708
COM8
Full functional RS-232
COM9
4-wire RS-232 (TXD/RXD/RTS/CTS)
COM10
For WWAN module
COM11
For WWAN module
Table 4.7: Serial Port Settings
Port
Address Range
Interrupt
COM1
3F8 ~ 3FF
COM2
2F8 ~ 2FF
COM3
2E8 ~ 2EF
COM4
2D8 ~ 2DF
COM5
2E0 ~ 2E7
10
11
COM6
TREK-550 User Manual
28
Chapter
A
Pin Assignments
This appendix explains pin
assignments on the TREK-550.
Sections include:
!Internal Speaker Connector
!COM1, 2
!GPIO / CAN BUS connector
(CN31)
!Inverter / Touch / USB connector
(CN18)
!Power Inlet
5.1 Front Side Connectors
5.2 Rear Side Connectors
5.3 Power Connector (12/ 24V; 6 ~ 36V)
Molex Manufacturer part no. 0430451200
Power Connector
Pin
Signal
Pin
Signal
Chassis Ground
Ground
Ground
(Reserved)
(Reserved)
(Reserved)
Power Input (6~36 VDC)
Power Input (6~36 VDC)
Acc Ignition Input
10
Ground
11
(Reserved)
12
Power Button Input
TREK-550 User Manual
22
5.4 Smart Display Connector
Smart Display Connector
Pin
Signal
Pin
Backlight Enable output
Panel Power Enable output
LVDS Ground
Reset Button Input
LVDS Clock +
LVDS Clock -
LVDS Ground
LVDS Ground
LVDS Data2 +
10
LVDS Data2 -
11
RS232 TXD1
12
RS232 RXD1
13
LVDS Data1 +
14
LVDS Data1 -
15
LVDS Ground
16
LVDS Ground
17
LVDS Data0 +
18
LVDS Data0 -
19
USB D+
20
USB D-
21
USB Ground
22
USB Ground
23
+12VDC output
24
+12VDC output
25
+12VDC output
26
+12VDC output
27
Power Ground
28
Power Ground
29
Power Ground
30
Power Ground
31
RS232 TXD2
32
RS232 RXD2
33
RS232 RTS2
34
Power Button Input
35
Audio Ground
36
Mono. Line-out
TREK-550 User Manual
Signal
22
5.5 RS-232 Connector
RS-232 / RS-485 / J1708 Connector
Pin
Signal
Pin
Signal
RS-232 DCD
RS-232 RXD
RS-232 TXD
RS-232 DTR
RS-232 Ground
RS-232 DSR
RS-232 RTS
RS-232 CTS
RS-232 RI / +5V / +V12
5.6 RS-232 / RS-485 / J1708 Connector
RS-232 / RS-485 / J1708 Connector
Pin
Signal
Pin
RS-232 RTS9
RS-232 RXD9
RS-232 TXD9
RS-232 CTS9
RS-232 Ground
RS-485 D-
RS-485 D+
J1708 D-
J1708 D+
TREK-550 User Manual
Signal
22
5.7 DI / DO Connector
DI / DO Connector
Pin
Signal
Pin
Signal
Isolated Dry Contact Input 1
Isolated Dry Contact Input 2
Isolated Dry Contact Input 3
Isolated Dry Contact Input 4
Isolation Ground
Isolated Relay Driver Output 1
Isolated Relay Driver Output 2
Isolated Relay Driver Output 3
Isolated Relay Driver Output 4
5.8 CAN / Video-In Connector
CAN / Video-In Connector
Pin
Signal
Pin
Signal
CAN_H
CAN_L
CAN_SHIELD
CAN_SHIELD
Video In 2
Video Ground
Video In 1
Video Ground
TREK-550 User Manual
22
5.9 LED indicator
TREK-550 User Manual
22
Chapter
Software demo
application setup
C
This appendix explains the
software demo application for
TREK-550.
Sections include:
!Introduction
!How to set up demo application
6.1 Introduction
To make the hardware easier to access for programmers, Advantech has developed
an demo program in order to let customer test the functions on TREK-550. This
document describes detailed information for each Advantech demo program so that
application developers can becomemorefamiliar with using them.
For technical support, contact Advantech application engineers worldwide.
For news updates, visit our website:www.advantech.com
6.1.1 Execute J1939 demo program
Thissection explainshow to install theAdvantech demo program in Windows XP Pro /
Embedded.
1. Execute the test program called “IMC_Demo”
Figure 6. 1
2. Click J1939: customer may connect directly to the truck; we use a simulator board
below to explain how J1939 protocol can be executed.
First, connect to the simulator board to TREK-550 CAN port and console PC,
once the simulator is powered on (connect to the truck), you can start getting the
data, just click [Read], you may get the data you need from the simulator, click
[Read], you may transfer the data to Console
Smulator vendor name:
TREK-550 User Manual
43
www.advantech.com
22
Figure 6.2
Figure 6.3
TREK-550 User Manual
44
www.advantech.com
J1939 truck simulator
Figure 6.4
22
6.1.2 CAN Test
1. CAN: Console PC, install [PCAN_USB-to-CAN] test program, and use USB to
CAN fixture to connect to TREK-550 CAN port.
2. Execute PCAN-View USBĺ Set Baud rate 250kBit/sĺ Select [Extended]ĺOKĺ
Transmit ĺ New ĺ ID(Hex) key in number ĺ Data key in any numberĺ[Period]
key in 100msĺClick [Extended Frame]ĺOK. See below figure 6.
Figure 6. 11
Figure 6. 12
TREK-550 User Manual
45
www.advantech.com
22
Figure 6. 13
3. Then you may read the data of TREK-550 from Console PC, in the same time,
you may also press [Write Data] to write to Console PC. As for Filter Message, it
can filter out the message you don’t need, and keep the message you need. See
below Figure 6.
Figure 6. 14
TREK-550 User Manual
46
www.advantech.com
22
6.2
RTC test
Execute “RTC test”
1. For RTC Time setting: You may set year, month, date, and time show as below.
Figure 6.5
Figure 6.6
Figure 6. 7
Figure 6. 8
2. RTC Alarm Setting: You may also set Alarm time; you may wake up the system
by the time you have set. Please refer to below figure 6.
TREK-550 User Manual
47
www.advantech.com
22
Figure 6.9
6.3
Power Management
6.3.1
Power management Mechanism
Normal Power Management Flow
OFF_EVENT_DELAY
ON_DELAY
T1
T2
IgnitionON
T3
HARD_OFF_DELAY
T4
IgnitionOFF
SystemON
48
www.advantech.com
T5
SystemOFF
SendPower
ButtonSignal
Low Battery Protection
LOW_DELAY
LOW_HARD_DELAY
T8
SystemstaysON
T7
T6
SystemOFF
LowBatteryis
Detected
SendPower
ButtonSignal
When the system is ON, and
(1) The battery voltage (DC input) is lower than LOW_THRESHOLD (at T6)
(2) and this situation lasts for LOW_DELAY,
, then the system will send Power Button signal to OS (at T7) to start the shutdown process.
At this time (T7), the LOW_HARD_DELAY is starting to countdown.
Once LOW_HARD__DELAY is over, the system power is removed abruptly.
Before
T1
T 1 ~ T2
T2
T 2 ~ T3
T3
T 3 ~ T4
T4
T 4 ~ T5
T5
After T5
T1
The system stays off.
power is fed in, but Ignition is OFF.
Ignition is ON and the ON_DELAY is starting to count down.
This duration is and it is ranged from 1 to 18000 seconds.
Once the ON_DELAY is over, the system will stay On or OFF, depending on the
BIOS setting “POWER-ON after Power Fail”.
If “POWER-ON after Power Fail” is set as ON, the system will be powered ON.
If “POWER-ON after Power Fail” is set as OF, the system will stay OFF and you
could press the power button to turn on system.
The system is under normal operation.
At this time, the Ignition is OFF, and OFF_EVENT_DELAY is starting to count
down.
This duration is OFF_EVENT_DELAY and it is ranged from 1 to 18000 seconds.
When the OFF_EVENT_DELAY is over, the system will send a power button
signal to the OS and the user application should prepare the shutdown process.
The HARD_OFF_DELAY is starting to count down.
This duration is HARD_OFF_DELAY and it is ranged from 1 to 18000 seconds.
When the HARD_OFF_DELAY is count to zero, the system power is removed
abruptly to avoid extra and abnormal power drain from battery.
This parameter is fixed with a value of 60 seconds.
The system stays off.
LOW_DELAY is ranged from 1 to 3600 seconds.
LOW_HARD_ DELAY is fixed with a value of 60 seconds.
49
www.advantech.com
Note:
Q1: How is the low-battery event raised or canceled?
A1: The minimum value on LOW_DELAY parameter is 1 second. If the voltage remains lower
than the LOW_THRESHOLD in the duration of LOW_DELAY, the low-battery event will be
raised and immediately send a power button press signal to OS.
During the duration of LOW_DELAY, if the battery voltage is back to be higher than
LOW_THRESHOLD, the LOW_DELAY will be reset to predetermined value and stop count
down.
Therefore, the LOW_DELAY parameter acts as a filter to prevent incorrect low-battery-event
from happening.
6.3.2 Power Management demo program
A. Check the files.
Make sure that there are two components include in TREK-550 Power Management Tool. One
is “AdvXP_CAN.dll”, another one is “TREK-550 Power Manager.exe”.
B. Start up the program
Execute Power Management tool and you will see a message box shows “Connect OK”.
Then Click OK button and you will see the main page as below.
6.3.3 Power Management Parameter settings
The parameters for power management on TREK-550 could be set by Demo program (see the
image below) or SDK/API.
TREK-550 User Manual
50
www.advantech.com
22
Figure 6.9 power management demo utility
Figure 6.9 Off event delay
Off Event Delay – it means after 5 seconds delay from receiving of ignition OFF signal, EC
controller will send a shutdown event to make system start shutdown process
Figure 6.9 Hard Off delay
Hard off Delay – it means after 30 seconds from shutdown event, EC controller will force
power cut off at the same time.
Figure 6.9 On delay
On Delay – it means after 2 seconds from receiving of ignition ON signal, EC controller will
send a power-on event to make system start booting process.
Figure 6.9 Low delay
51
www.advantech.com
Low Delay – it means after 30 seconds delay from receiving of Battery Voltage LOW signal,
EC controller will send a shutdown event to make system start shutdown process.
Figure 6.9 Low hard delay
Low Hard Delay – it means after 60 seconds from Low Voltage shutdown event, EC controller
will force power cut off at the same time
Figure 6.9 Battery voltage Threshold level setting
You could set the LOW battery voltage value by changing level 0 to 65. For example, if you’re
using 12V battery, and you set level as 50, it means the LOW battery voltage value is 10.147 +
50 x 0.0146 = 10.877 V.
Checks which source you’re connecting. DC supply or 12V or 24V battery.
Figure 6.9 check 12 or 24 battery
Check the ignition signal and see if it’s ON or OFF.
C. Read current status
The buttons which indicates by red squares can READ the current status of the system.
TREK-550 User Manual
52
www.advantech.com
22
Figure 6.9 Read the value
D. Set the value
53
www.advantech.com
The buttons which indicates by blue squares can SET the value you want to the system.
Figure 6.9 Set value
Execute “Power management test”, the Battery Voltage Level has 12V and 24V,
you may set from 0~65 levels, press “Get” to know the value you set.
54
www.advantech.com
Figure 6.10
1. Off Event Delay: You may set how many seconds you want system auto shut
down after ignition off.
2. On Delay: You may set how many seconds you want the system to auto power
on.
3. Low Delay: When the battery voltage is below certain value you set, it will
automatically shut down to prevent the system will consume the battery.
6.3.4 TREK-550 power consumption
OS: Windows Embedded Standard
Burn-in test V6.0
Idle Mode
12V / 1.04A
12V / 1.51A
w/o TREK-303H
w/ TREK-303H
100% Burn-in Test Mode
12V / 1.20A
12V / 1.94A
Off mode (S5)
12V / 1.75mA
*Doesn’t support S1, S3, S4
6.4
GPIO Test
1. Execute I/O Test, connect GPIO loopback, click Pin0ĺSet, the end which Read
the signal, the bulb will be light up, like wise to Pin1~Pin3. Next pick Digital output
to execute the same procedure. See figure 6.
Figure 6.15
55
www.advantech.com
a. Digital Output Î isolated relay driver output
b. Digital Input Î isolated dry contact input
Figure 6.15 Digital in
Figure 6.15 Digital out
6.5
Video in Test
There are two video in, please connect camera on each port, CAM1 &
CAM2, choose Channel 1 on [Switch to], then panel will show the image
which camera1 has taken, it will recover to the same status after 10 sec,
then change to Channel 2, Panel will show what appears on camera2, and
come back to the same status after 10 sec.
56
www.advantech.com
Figure 6.16
6.6
Dead reckoning
We will need a 3-axis accelerometer that our software can talk to.
We use this to characterize driver behavior such as hard accelerations,
braking, and cornering. This also can tell us other significant information
that can be used in accident reconstruction, etc… This one of the crucial
items that we asked for in our specification and our customers’
expectations are making this a definite must have in our system. We won’t
be needing any dead reckoning functionality at this point in time… this is
something we may want to include in the future but in order to get cost
down we have decided to forgo this at this time. Please confirm that we
will have access to this or another accelerometer.
6.7
G- sensor
We currently, we don’t have documents about G-sensor, but a code
example is ready for customer reference. This code example ONLY
introduces how to access the G-sensor under Windows XP/XPe, but users
must control the G-sensor and develop their SW application by themselves.
Therefore, customer can decide how to set the sensitivity value when to
trigger G-sensor to send signal to CPU and to back end server through
WWAN module. G-sensor is located on the motherboard inside the
TREK-550. Please refer the link
(http://www.analog.com/static/imported-files/data_sheets/ADXL345.pdf) for
the G-sensor datasheet.
TREK-550 User Manual
57
www.advantech.com
22
Appendix
C
TREK-303
This appendix explains the
TREK-303 detailed information.
58
www.advantech.com
Appendix A Paired with TREK-303 Specifications
Table 1.1: TREK-303 Specifications
Definition
DetailDisplay type:
7” TFTLCDMax.
resolution:
800 x 480
Colors: 262K
Dotsize (mm)
0.0635 x0.1905
Luminance: 500cd/m2
ViewingAngle (R/L/B/T)
70° /70°/60°/60°
Note!
1.
The Brightness control is adjusted by the auto light sensor in the
front panel as default; it is also defined by buttonon thefront
panel by manual.
2. The color LCD display
59
www.advantech.com
TREK-303 Specification
TREK-303 demo SW application program
Figure 6. 17
60
www.advantech.com
1. Execute “Hot Key test” program Î
2. Brightness level: You may set panel’s brightness from level 0 ~10, total 10
levels, when you finish setting the brightness level you want, please click
“Apply”. If you want to check the current brightness level of TREK-303, please
click “Get”.
3. Duty cycle: You may set every level’s brightness strength, total 10 levels,
when you finish setting the brightness strength for each level, please click
“Apply”. If you want to check the current brightness strength on certain level of
TREK-303, please click “Get”.
4. Light sensor: When the sensor has detected the change of the brightness in
the environment, the value will change. The lowest level of brightness, the
lowest value it is presented. On the contrary, the highest level of brightness,
the highest value it is presented.
5. Hotkey: You may set the hotkey LED light brightness, the value is from 0
~100.
6. Key Status: When you press Hot key, the status will change from 0 to 1.
7. Key function Definition: You may set the parameter to connect the
application program of the hot key.
61
www.advantech.com
TREKͲ
Dipol
boAntenna
Comb
K-550 A2/303 User
TREK
44
75(.$17(11$,QVWDOODWLRQ3KRWR
www.advantech.com
Please verify specifications before quoting. This guide is intended for
referencepurposes only.
All product specifications are subject to change without notice.
No part of this publication may be reproduced in any form or by any
means,electronic, photocopying, recording or otherwise, without prior
written permission of the publisher.
All brand and product names are trademarks or registered trademarks
of theirrespective companies.
© Advantech Co., Ltd. 2010
62
www.advantech.com
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 59 XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:16acd2ba-7158-49ed-a08d-462b391bbc0f Producer : Acrobat Distiller 6.0 (Windows) Create Date : 2013:08:29 14:24:09+08:00 Creator Tool : PScript5.dll Version 5.2 Modify Date : 2013:08:30 11:23:34+08:00 Metadata Date : 2013:08:30 11:23:34+08:00 Document ID : uuid:3058f387-168b-49b3-97c2-a404fbca70e8 Format : application/pdf Creator : USER Title : TREK-550 A2 user manaul -0829.pdf Author : USEREXIF Metadata provided by EXIF.tools