Alvarion Technologies IF-MMDS1 Outdoor MDS transceiver User Manual BST 2 5 27

Download:
Mirror Download [FCC.gov]
Document ID	117131
Application ID	Q3fjunIKXod6bDjsq1ur6Q==
Document Description	Corrected user manual 2 of 2
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	123.95kB (1549384 bits)
Date Submitted	2000-09-14 00:00:00
Date Available	2000-10-30 00:00:00
Creation Date	0000-00-00 00:00:00
Producing Software	Acrobat Distiller 3.0 for Windows
Document Lastmod	2000-09-11 11:45:15
Document Title	Microsoft Word - BST 2.5 _27.
Document Creator	PSCRIPT.DRV Version 4.0

BreezeACCESS MMDS
Base Station Equipment
Installation
Manual
July, 2000
Cat. No. 213101
Front Matter
© 2000 by BreezeCOM Ltd. All rights reserved.
No part of this publication may be reproduced in any material form without the written permission of
the copyright owner.
Trade Names
BreezeACCESS, BreezeNET, BreezeLINK, BreezeVIEW, BreezeMANAGE and WIX are trade
names of BreezeCOM Ltd. Other brand and product names are registered trademarks or trademarks of
their respective companies.
Statement of Conditions
The information contained in this manual is subject to change without notice. BreezeCOM shall not be
liable for errors contained herein or for incidental or consequential damages in connection with the
furnishing, performance, or use of this manual or equipment supplied with it.
Warranty
In the following warranty text, “the Company” shall mean:
•
BreezeCOM Ltd., for products located outside the USA.
•
BreezeCOM Inc., for products located in the USA.
This BreezeACCESS product is warranted against defects in material and workmanship for a period of
one year from date of purchase. During this warranty period the Company will, at its option, either
repair or replace products that prove to be defective.
For warranty service or repair, the product must be returned to a service facility designated by the
Company. Authorization to return products must be obtained prior to shipment. The buyer shall pay all
shipping charges to the Company and the Company shall pay shipping charges to return the product to
the buyer.
The Company warrants that the firmware designed by it for use with the unit will execute its
programming instructions when properly installed on the unit. The Company does not warrant that the
operation of the unit or firmware will be uninterrupted or error-free.
Limitations of Warranty
The foregoing warranty shall not apply to defects resulting from improper or inadequate maintenance
by the buyer, buyer supplied interfacing, unauthorized modification or misuse, operation outside of the
environmental specifications for the product, or improper site preparation or maintenance. No other
warranty is expressed or implied. The Company specifically disclaims the implied warranties of
merchantability and fitness for any particular purpose.
BreezeCOM shall not be liable to any person for any special or indirect damages, including, but not
BS Equipment Installation Manual
ii
BreezeACCESS MMDS Series
Front Matter
limited to, loss of profits or revenues, loss of use or damage to any associated equipment, cost of
capital, cost of substitute products, facilities or services, downtime costs or claims resulting from any
cause whatsoever arising from or in any way connected with the manufacture, sale, handling, service,
repair, maintenance or use of the products. In no event shall the company’s liability exceed the
purchase price denoted on the invoice.
Information to User
Any changes or modifications of equipment not expressly approved by the manufacturer could void
the user’s authority to operate the equipment.
Safety Considerations
For the following safety considerations, “Instrument” means the BreezeACCESS Base Station
equipment components and cables.
Caution
To avoid shock, do not perform any servicing unless you are qualified to do so.
To comply with FCC RF exposure requirements in section 1.1307, a minimum separation distance of
64 cm (26 inches) is required between this antenna and all persons.
Line Voltage
Before connecting this instrument to the power line, make sure that the voltage of the power source
matches the requirements of the instrument.
Radio
The instrument transmits radio energy during normal operation. To avoid possible harmful exposure to
this energy, do not stand or work for extended periods of time in front of its antenna. The long-term
characteristics or the possible physiological effects of Radio Frequency Electromagnetic fields have
not been yet fully investigated.
Antenna Installation and Grounding
Be sure that the Outdoor unit, the antenna and the supporting structure are properly installed to
eliminate any physical hazard to either people or property. Verify that the antenna mast is grounded so
as to provide protection against voltage surges and static charges. Make sure that the installation of the
antenna and cable is performed in accordance with all relevant national and local building and safety
codes.
BreezeACCESS MMDS Series
iii
BS Equipment Installation Manual
Table of Contents
1. INTRODUCTION ..................................................................................................................... 1
2. BASIC INSTALLATION ......................................................................................................... 2
2.1 Packing List – Modular Shelf Equipment............................................................................. 2
2.1.1 BS-SH Base Station Shelf.............................................................................................. 2
2.1.2 AU-A/E-BS Access Units (up to six per shelf) ............................................................. 2
2.1.3 BS-PS Power Supply (one or two per shelf).................................................................. 2
2.2 Packing List – Stand-alone AU-A/E-NI Access Unit ........................................................... 3
2.3 Other Items Required for Installation ................................................................................... 3
2.4 Guidelines for Selection of Equipment Location.................................................................. 3
2.5 Installing the Outdoor Radio Unit......................................................................................... 6
2.5.1 Mounting the Outdoor Unit ........................................................................................... 6
2.5.2 Connecting the Antenna Cable (AU-RE) ...................................................................... 8
2.5.3 Connecting the Ground and IF Cables........................................................................... 8
2.6 Installing the Modular Shelf Indoor Equipment ................................................................... 9
2.6.1 BS-SH Slot Assignments ............................................................................................... 9
2.6.2 The BS-AU .................................................................................................................. 10
2.6.3 The BS-PS ................................................................................................................... 12
2.6.4 Shelf and Modules Installation Procedure ................................................................... 13
2.7 Installing the AU-NI Indoor Unit........................................................................................ 14
3. CONFIGURING SYSTEM PARAMETERS ....................................................................... 15
3.1 Getting Started with the Local Terminal............................................................................. 15
3.2 Configuration Parameters ...................................................................................................17
3.3 Reset Unit............................................................................................................................ 19
BreezeACCESS MMDS Series
SU A/E Subscriber Units Installation Manual
Table of Contents
4. VERIFYING CORRECT OPERATION .............................................................................. 20
4.1 Verifying Correct Operation of the AU-A/E-BS ................................................................ 20
4.2 Verifying Correct Operation of the AU-A/E-NI................................................................. 20
4.3 Verifying Correct Operation of the Outdoor Unit............................................................... 21
5. SPECIFICATIONS ................................................................................................................. 22
5.1 Radio ................................................................................................................................... 22
5.2 Outdoor Unit to Indoor Unit Communication..................................................................... 22
5.3 Configuration and Management.......................................................................................... 23
5.4 Interfaces............................................................................................................................. 23
5.5 Electrical ............................................................................................................................. 24
5.6 Mechanical .......................................................................................................................... 24
5.7 Environmental..................................................................................................................... 24
5.8 Standards Compliance, General .......................................................................................... 24
APPENDIX A. USING TELNET
APPENDIX B. MMDS CHANNELS AND FREQUENCIES
BS Equipment Installation Manual
vi
BreezeACCESS MMDS Series
Table of Contents
Table of Figures
Figure 2-1. Holes/Grooves/Screw Holes................................................................................... 6
Figure 2-2. AU-RE 3" Pole Mounting Installation Using the Supplied Brackets..................... 7
Figure 2-3. AU-RA/AU-RE Radio Unit Bottom Panel.............................................................. 8
Figure 2-4. Shelf Slot Assignments .......................................................................................... 9
Figure 2-5. BS-AU Front panel............................................................................................... 10
Figure 2-6. BS-PS Front Panel................................................................................................ 12
Figure 2-7. AU -NI Rear Panel ................................................................................................ 14
Figure 2-8. AU -NI Front Panel ............................................................................................... 14
Figure 3-1. Main Menu ........................................................................................................... 16
Figure 3-2. Basic Configuration Menu ................................................................................... 18
Table of Tables
Table 2-1: IF Cables................................................................................................................... 4
Table 2-2: BS-AU LEDs .........................................................................................................11
Table 2-3: BS-PS Power Supply LEDs.................................................................................... 12
Table 4-1: AU-NI LEDs........................................................................................................... 20
Table 4-2: AU-RA/RE LEDs ................................................................................................... 21
BreezeACCESS UMDS Series
vii
BS Equipment Installation Manual
Introduction
1. INTRODUCTION
This manual describes installation guidelines for BreezeACCESS MMDS base
station equipment, including the stand-alone AU-E/A-NI-MMDS Access Units
and the modular AU-E/A-BS-MMDS Units with the BS-SH rack mounted shelf.
The BreezeACCESS IP Broadband Wireless Local Loop (WLL) system allows
access service providers to provide high-speed IP connectivity services to their
subscribers. To support IP-based services effectively BreezeACCESS systems
employ wireless packet data switching technology.
The BreezeACCESS MMDS line of products uses Frequency Hopping Spread
Spectrum radios that operate in Time Duplex Division (TDD) mode in the
2.500GHz – 2.686GHz frequency range.
The AU-A/E-NI and the AU-A/E-BS Access Units are comprised of an indoor
unit and an outdoor unit. In the AU-A-NI and AU-A-BS products, the outdoor
unit (AU-RA) contains the radio module and an integral flat antenna. In the
AU-E-NI and AU-E-BS products, the outdoor unit (AU-RE) contains the radio
module and an interface to an external antenna (not included).
The indoor unit of the AU-A/E-NI is a stand-alone unit (AU-NI) that is powered
from the mains via its AU-PS power supply unit. The indoor unit of the AU-A/EBS is a module (BS-AU) that is designed for insertion into the BS-SH shelf. The
BS-SH, which is a 3U shelf suitable for installation in 19 racks, can contain up
to six BS-AU active modules and one or two BS-PS power supply modules. The
shelf is powered from a –48VDC power source. Power supply redundancy is
supported through the optional use of a second BS-PS power supply module.
The indoor unit provides the interface to the network. It also contains an IF
(Intermediate Frequency) module and is connected to the outdoor unit via a
50-ohm coaxial IF cable. The IF cable serves for transmission of the 440MHz IF
signal between the indoor and the outdoor units. It also serves for transferring
power (12VDC), management and control signals from the indoor unit to the
outdoor unit.
Note: The information contained in this manual is applicable to
BreezeACCESS MMDS units with software release 2.5.
BreezeACCESS MMDS Series
BS Equipment Installation Manual
Basic Installation
2. BASIC INSTALLATION
2.1 Packing List – Modular Shelf Equipment
2.1.1 BS-SH Base Station Shelf
•
BS-SH shelf (with blank panels)
•
Rubber legs for optional desktop installation
Note:
Unless ordered otherwise, each BS-SH will be shipped with one BS-PS
power supply installed.
2.1.2 AU-A/E-BS Access Units (up to six per shelf)
•
Outdoor unit:
⇒ AU-RA with integral antenna
or
•
•
•
⇒ AU-RE with a connector to an external antenna (not included)
Pole mounting kit for the outdoor unit (with two brackets, four sets of
screws, nuts and washers)
BS-AU Network Interface module
Monitor cable
2.1.3 BS-PS Power Supply (one or two per shelf)
•
BS-PS Power Supply module
•
Power cable
BS Equipment Installation Manual
BreezeACCESS MMDS Series
Basic Installation
2.2 Packing List – Stand-alone AU-A/E-NI Access Unit
•
AU-NI indoor unit
•
Outdoor unit:
⇒ AU-RA with integral antenna
or
⇒ AU-RE with a connector to an external antenna (not included)
•
AU-PS power supply with a mains power cord
•
Pole mounting kit for the Outdoor unit (with two brackets, four sets of
screws, nuts and washers)
•
Wall mounting kit for the AU-NI unit
2.3 Other Items Required for Installation
•
•
•
•
•
•
IF cable (s)* (one for each AU)
Grounding cable(s) with an appropriate termination (one for each AU)
Ethernet cable(s) (straight, one for each AU)
Antenna(s)* and RF cable(s)* (AU-E-NI or AU-E-BS only)
A portable PC with terminal emulation software
Installation tools and materials.
Items marked with an asterisk (*) are available as options from BreezeCOM.
2.4
Guidelines for Selection of Equipment Location
Select appropriate locations for the equipment using the following guidelines:
•
The outdoor unit can be pole—or wall mounted. Its location should allow
easy access to the unit for installation and testing.
•
The AU-RA unit with its integrated antenna, or the external antenna
connected to the AU-RE unit, should be installed where it provides coverage
of all subscriber units in the area it is intended to serve. The higher the AURA or the antenna, the better coverage it can provide.
BreezeACCESS MMDS Series
BS Equipment Installation Manual
Basic Installation
•
The AU-RE outdoor unit should be installed as near as possible to its
antenna.
Note:
•
The distance between any two antennas should be greater than 40 cm.
The outdoor unit is connected to the indoor unit by means of a coaxial IF
cable carrying signals, controls and power. The IF frequency is 440 MHz.
The maximum allowed attenuation of the IF cable is 15dB and its maximum
allowed DC resistance (the sum of the DC resistance of the inner and outer
conductors) is 1.5 ohm. This allows for cable lengths of up to 30m when
using the standard RG 58 cable. If longer cables are required, a cable with
lower attenuation and/or DC resistance should be used.
Table 2-1 provides data regarding several industry-standard cables such as
RG 58 and RG 213. If the spectral environment is polluted with noise in the
440 MHz band, it is recommended to use a higher quality double-shielded
cable such as LMR 240 or LMR 400 (manufactured by Times
Communications).
Table 2-1: IF Cables
Cable Type
Maximum cable
Length (m)
•
RG 58
RG 213
LMR 240
LMR 400
30
100
65
150
The BS-SH and its modules and the SU-NI are designed for indoor
operation, i.e., inside buildings, a suitable cabinet or a shelter. Air
temperature control might be necessary – the equipment is designed to
operate over the temperature range 0°C to 45°C.
BS Equipment Installation Manual
BreezeACCESS MMDS Series
Basic Installation
Note:
Outdoor units and antennas should be installed ONLY by experienced
installation professionals who are familiar with local building and safety
codes and, wherever applicable, are licensed by the appropriate government
regulatory authorities.
The system complies with the ETS 300 385 standard and is protected against
secondary lightning strikes when its outdoor unit is properly grounded
according to the applicable country-specific industry standards for
protection of structures against lightning.
Failure to do so may void the BreezeACCESS product warranty and may
expose the end user or the service provider to legal and financial liabilities.
BreezeCOM and its resellers or distributors are not liable for injury,
damage or violation of regulations associated with the installation of
outdoor units or antennas.
BreezeACCESS MMDS Series
BS Equipment Installation Manual
Basic Installation
2.5 Installing the Outdoor Radio Unit
2.5.1 Mounting the Outdoor Unit
The outdoor unit can be secured to the pole using one of the following options:
•
Special brackets and open-ended screws (supplied with each unit). There are
two pairs of screw holes, allowing use of the brackets with various pole
widths.
•
U-bolts - size A (inner installation holes, up to 2" pole).
•
U-bolt - size B (outside installation holes, up to 3" pole).
•
Metal bands (9/16” wide, minimum 12” long).
Figure 2-1 shows the locations of the holes, grooves and screw holes on the rear
side of the unit.
Figure 2-2 illustrates the method of installing an AU-RE unit on a pole using the
supplied brackets and open-ended screws. The installation of an AU-RA unit
with an integral antenna is very similar to the installation of an SU-RE unit.
Note:
Make sure to install the unit with the bottom panel (the panel with the IF
connector) facing downward.
G roo ve s fo r In sertion of 9 /16 ” M eta l B a n d
U -B olts (3” P ole)
U -B olts (2” P ole)
B ra cke t S crew s
Figure 2-1. Holes/Grooves/Screw Holes
BS Equipment Installation Manual
BreezeACCESS MMDS Series
Basic Installation
Figure 2-2. AU-RE 3" Pole Mounting Installation Using the Supplied
Brackets
Note:
When inserting the open-ended screws, make sure to insert them with the
grooves pointing outwards; these grooves are intended to allow fastening of
the screws with a screwdriver.
BreezeACCESS MMDS Series
BS Equipment Installation Manual
Basic Installation
2.5.2 Connecting the Antenna Cable (AU-RE)
Connect an RF cable between the ANT connector (located on the top panel of the
unit, marked ANT) and the antenna.
2.5.3 Connecting the Ground and IF Cables
The Ground terminal (marked and the IF cable connector (marked IF) are
located on the bottom panel of the Outdoor unit, shown in Figure 2-3.
Ground
Screw
Figure 2-3. AU-RA/AU-RE Radio Unit Bottom Panel
1. Connect one end of the grounding cable to the Ground terminal and connect
the other end to a good ground connection.
2. Connect the coaxial cable to the IF connector. Verify that the length of the IF
cable is sufficient and that it can easily reach the Indoor unit.
Note:
Make sure to switch OFF the power of the indoor unit prior to
connecting/disconnecting the IF cable.
BS Equipment Installation Manual
BreezeACCESS MMDS Series
Basic Installation
2.6 Installing the Modular Shelf Indoor Equipment
2.6.1 BS-SH Slot Assignments
The Base Station shelf has ten slots, as shown in Figure 2-4
8 Middle slots - BS-AU modules
B S -A U
3:5
$/50
B S -A U
B S -A U
B S -A U
B S -A U
B S -A U
3:5
:/1.
0$67(5 $/50
3:5
:/1.
0$67(5 $/50
3:5
:/1.
0$67(5 $/50
3:5
:/1.
0$67(5 $/50
3:5
:/1.
0$67(5 $/50
:/1.
0$67(5
5(6(7
2))
21
5(6(7
2))
21
5(6(7
2))
21
5(6(7
2))
21
5(6(7
2))
21
5(6(7
2))
21
ETH
ETH
ETH
ETH
ETH
ETH
IF
IF
IF
IF
IF
IF
MON
MON
MON
MON
MON
MON
Extreme slots - Power Supply modules
Figure 2-4. Shelf Slot Assignments
The two wide slots on the both sides of the shelf accommodate the BS-PS power
supply modules. The shelf is designed to support power supply redundancy
through the use of two Power Supply modules. If a single power supply is used,
it can be inserted in any of the two available slots.
The remaining eight slots can accommodate up to six active BS-AU modules.
Two extra slots are for future use. Active BS-AU modules can be installed in any
of the 8 slots. Unused slots should be covered by blank panels.
BreezeACCESS MMDS Series
BS Equipment Installation Manual
Basic Installation
2.6.2 The BS-AU
The BS-AU front panel is shown in Figure 2-5.
B S -A U
3:5
$/50
:/1.
0$67(5
5(6(7
2))
21
ETH
IF
MON
Figure 2-5. BS-AU Front panel
The BS-AU provides the following interfaces:
An Ethernet connector (ETH) for connecting the BS-AU to the network. This
connector should be connected to a straight Ethernet cable.
An IF connector for connecting the BS-AU to an outdoor AU-RE or AU-RA
radio unit. The outdoor radio unit provides the air link between the BS-AU and
the remote Subscriber Units.
A MON connector for connecting an ASCII terminal with terminal emulation
software for configuration and maintenance purposes.
BS Equipment Installation Manual
10
BreezeACCESS MMDS Series
Basic Installation
The BS-AU front panel LEDs are described in Table 2-2.
Table 2-2: BS-AU LEDs
Name
PWR
WLNK
ALRM
MASTER
ETH
connector
embedded
LED
ETH
connector
embedded
LED
Description
Power supply
12 VDC
Wireless link
activity
ALARM
Indication
Master
Indication
Ethernet
activity
ETH Link
Integrity
Functionality
On – 12 VDC power is supplied to AU-RE
Off – 12 VDC power is not supplied to AU-RE
Blinking –Receiving packet from the wireless link
Off – No reception of packets from the wireless
link
On – Loss of hopping synchronization (slave units)
On – The unit is configured as a Master
On- Receive/Transmit on Ethernet port
Off- No Receive/Transmit on Ethernet port
On- Unit is connected to Ethernet segment
Off- Unit is not connected to Ethernet segment
The switch on the BS-AU front panel controls the supply of 12 VDC power to
the outdoor unit via the IF cable. The momentary RESET position of this switch
is for resetting the outdoor unit. In the OFF position, power is not supplied to the
outdoor unit, even when the BS-AU unit is still ON.
BreezeACCESS MMDS Series
11
BS Equipment Installation Manual
Basic Installation
2.6.3 The BS-PS
The BS-PS provides -48VDC to all the modules installed in the BS-SH rack. The
BS-PS front panel is shown in Figure 2-6.
B S -P S
PW R
5V
12V
ON
ON
OFF
-48V
Figure 2-6. BS-PS Front Panel
The BS-AU provides a single connector for connecting the -48VDC power
source to the module. The color codes of the cable wires are:
black
red
-48VDC
+ (Return)
The switch turns the mains power to the power supply ON and OFF.
Table 2-3: BS-PS Power Supply LEDs
Name
ON
5V
12V
BS Equipment Installation Manual
Description
-48 VDC is available and Power Supply is ON
The 5V power supply module is OK
The 12V power supply module is OK
12
BreezeACCESS MMDS Series
Basic Installation
2.6.4 Shelf and Modules Installation Procedure
1. Install the BS-SH rack in a 19” cabinet (or place on an appropriate
shelf/table). When mounted the BS-SH on a desktop, screw on the rubber
legs shipped with unit.
2. Carefully insert the BS-PS Power Supply and the BS-AU modules into their
intended slots and push firmly until they are securely locked; refer to
Section 2.6.1 for a description of the slot assignments. Close the captive
screws attached to each module. Place blank covers over all the unused slots.
3. Connect the IF cable(s) to the connector(s) marked IF located on the front
panel(s) of the BS-AU module(s) shown in Figure 2-5. The other side of the
IF cable is already connected to the outdoor unit.
4. Connect the DC power cord to the –48 DC In jack (marked –48V) located on
the front panel of the BS-PS power supply shown in Figure 2-6. If a
redundant power supply module is installed, connect a power cable to it as
well.
5. Connect the power cord(s) to the –48VDC power source. Connect the black
wire to the -48VDC contact of the power source. Connect the red wire to the
+ (Return) contact. Connect the shield to the Ground.
6. Switch the BS-PS power supplies to ON. Verify that all the power indicator
LEDs on the BS-PS front panel are ON. Refer to Table 2-3 for a description
of these LEDs.
7. Set the switches on the front panel of all BS-AU modules in the rack to ON.
BreezeACCESS MMDS Series
13
BS Equipment Installation Manual
Basic Installation
2.7 Installing the AU-NI Indoor Unit
1. Place the AU-NI unit in an appropriate location on a shelf or a table. The
unit can be wall mounted using the installation materials provided with the
unit. Use a 6mm (1/4”) drill and the supplied template plate for easy and
accurate marking of the holes.
2. Connect the AU -PS power cord to the DC In jack (marked DC-12V) located
on the rear panel of the Indoor unit (shown in Figure 2-6).
3. Connect the IF cable to the IF connector (marked IF) on the rear panel of the
Indoor unit. The other side of the IF cable should already be connected to the
Outdoor unit.
4. Connect the other end of the mains power cord to the AU -PS. Connect the
mains power plug to a mains power outlet.
DC - 12V
ETH
IF
Figure 2-7. AU -NI Rear Panel
5. Verify that the Power LED (marked PWR) located on the front panel of the
Indoor Unit is turned ON.
PW R
MON
WLNK
Figure 2-8. AU -NI Front Panel
6. Use a straight Ethernet 10baseT cable to connect the base station network
(e.g., a hub, switch or router) to the Ethernet port (marked ETH) located on
the rear panel of the AU-NI unit.
BS Equipment Installation Manual
14
BreezeACCESS MMDS Series
Configuring System Parameters
3. CONFIGURING SYSTEM PARAMETERS
After completing the installation process as described in the preceding section,
proceed with configuration of the basic system parameters.
This section covers the configuration of basic installation parameters. Refer to
the Administration Manual for information related to other parameters.
Note:
Optionally, the product can be configured using Telnet over the Ethernet
port, after setting the IP address. See Appendix A of this manual for further
information.
3.1 Getting Started with the Local Terminal
1. Connect one end of the Monitor cable to the MON jack on the front panel of
the BS-AU module or the AU-NI unit. Connect the second end of the cable
to the COM port of the terminal. The COM port connector on the Monitor
cable is a 9 pin D-type plug.
2. Run a terminal emulation program (e.g., ProComm or Windows
HyperTerminal) using the following setup:
Baud rate
Data bits
Stop bits
Parity
Flow Control
Connector
9600
None
Xon/Xoff
Available Com Port
3. Press Enter. The Select Access Level menu appears. Select the access level
according to your authorized access level. You will be requested to enter
your password. After entering the correct password press the Enter key.
The main menu appears as shown in Figure 3-1
BreezeACCESS MMDS Series
15
BS Equipment Installation Manual
Configuring System Parameters
Unit Type
BreezeACCESS/BST-AU
Official Release Version – 2.5.3
Software
Version No.
Release Date: Tue Jul 18 21:12:54 2000
Main Menu
=====================
1 – Info Screens
2 – Unit Control
3 – Basic Configuration
4 – Site Survey
5 – Advanced Configuration
BreezeACCESS >>>
Unit Name
Figure 3-1. Main Menu
The appearance of the displayed Main Menu varies in accordance with the
access level.
•
For users with read only access rights, only the Info Screens option is
displayed. Users with this access level cannot access the Unit Control,
Basic Configuration, Site Survey and Advanced Configuration menus.
•
For users with Installer access rights, the first four menu items (Info
Screens, Unit Control, Basic Configuration and Site Survey) are
displayed. Users with this access level cannot access the Advanced
Configuration menu.
•
For users with Administrator access rights, the full Main Menu will be
displayed. These users can access all the menu items.
BS Equipment Installation Manual
16
BreezeACCESS MMDS Series
Configuring System Parameters
4. Operate the monitor program as follows:
•
Type an option number to open/activate the option. You may need
to press the Enter key in some cases.
•
Press the Esc key to exit a menu or an option.
•
You can log-out and exit the monitor program at any time by
simultaneously pressing the Ctrl and X keys.
•
Reset the unit after making configuration changes for the new values
to take effect.
•
You can view the current parameters’ configuration by selecting 1 in
the Main Menu to Access the Info Screens menu, and then selecting
2 in the Info Screens menu to view the Basic Configuration
parameters.
3.2 Configuration Parameters
The following system parameters must be configured for each Access Unit:
•
•
•
•
•
•
•
•
•
Note:
ESSID
IP Address
Subnet Mask
Default Gateway Address
Hopping Band
Flexible sub-bands Definition (if Flexible Hopping was selected in the
Hopping Band menu)
Frequency Offset
Hopping Shift (if using two or more AUs)
Hopping Sync (if using two or more AUs)
You must select Reset Unit in the Unit Control menu for the changes to take
effect.
BreezeACCESS MMDS Series
17
BS Equipment Installation Manual
Configuring System Parameters
1. From the main menu, type 3 to access the Basic Configuration menu.
BreezeACCESS/BST-AU
Official Release Version – 2.5.3
Release Date: Tue Jul 18 21:12:54 2000
Basic Configuration
====================
1 – IP Address
2 – Subnet Mask
3 – Default Gateway Address
4 – ESSID
5 – Maximum Data Rate
6 – Frequency Offset
H – Hopping Band
F – Flexible sub-bands Definition
X - Transmit Power Control
S - Show Basic Configuration
BreezeACCESS >>>
Figure 3-2. Basic Configuration Menu
2. From the Basic Configuration menu, type 1 to access the IP Address
selection screen. Enter the required IP address.
3. Type 2 to access the Subnet Mask selection screen. Enter the required subnet
mask.
4. Type 3 to access the Default Gateway Address selection screen. Enter the
required default gateway address.
5. Type 4 to access the ESSID selection screen. Enter the required ESSID.
6. Type H to access the Hopping Band menu. Enter the required hopping band.
7. If Flexible Hopping was selected in the Hopping Band selection menu, type
F to access the Flexible sub-bands Definition menu. Use the Add/Delete subbands screens to define the required frequencies. See Appendix B for a list of
standard frequencies.
8. Type 6 to access the Frequency Offset selection screen. Enter the required
frequency offset.
9. If more than one AU is used, they should be synchronized for optimal
spectrum utilization. Type 7 to access the Hopping Shift selection screen and
BS Equipment Installation Manual
18
BreezeACCESS MMDS Series
Configuring System Parameters
enter the required shift. Type 8 to access the Hopping Sync selection screen.
Enter the required hopping sync status (Master or Slave).
Note:
Only one AU should be defined as a Master. The other units should be
defined as slaves. If only one AU is used, it should be defined as Idle.
3.3 Reset Unit
1. From the main menu, type 2 to access the Unit Control menu.
2. Type 1 to access the Reset Unit menu. Type 1 to reset the unit so that new
configuration settings are applied.
Note:
Should you make any mistakes during configuration or encounter any
problems associated with system configuration parameters, you may
configure the unit back to the factory defaults, as follows:
Type 2 in the Unit Control menu to access the Set Factory Defaults menu.
Type in 2 (Set Factory defaults-Full) to load the default values. Reset the
unit for the factory defaults values to take effect.
BreezeACCESS MMDS Series
19
BS Equipment Installation Manual
Verifying Correct Operation
4. VERIFYING CORRECT OPERATION
4.1 Verifying Correct Operation of the AU-A/E-BS
After completing the installation as described above, the system starts operation.
To verify correct operation, view the LED indicators located on the front panel of
the BS-AU modules as shown in Table 2-2 on page 11.
Note:
If the Access Units are not synchronized, reset the Master BS-AU unit and
then the Slave units to re-synchronize them.
4.2 Verifying Correct Operation of the AU-A/E-NI
To verify proper operation, view the LED indicators located on the front and rear
panels of the AU-NI unit as described in Table 4-1.
Table 4-1: AU-NI LEDs
Name
PWR
WLNK
Description
Functionality
Power Supply
12VDC
On – 12VDC power is supplied to the AU-NI
Wireless link
activity
Blinking –Receiving packet from the
wireless link
Off –Power is not supplied to the AU-NI
Off – No reception of packets from the
wireless link
ETH connector
embedded LED
Ethernet
activity
On – Receive/transmit on Ethernet port
ETH connector
embedded LED
ETH Link
activity
On – Unit is connected to Ethernet segment
BS Equipment Installation Manual
Off – No receive/transmit on Ethernet port
Off – Unit is not connected to Ethernet
segment
20
BreezeACCESS MMDS Series
Verifying Correct Operation
4.3 Verifying Correct Operation of the Outdoor Unit
To verify proper operation, view the LED indicators located on the bottom panel
of the Outdoor unit as shown in Figure 2-3 on page 8.
Table 4-2 lists the various LED states.
Table 4-2: AU-RA/RE LEDs
Name
ALARM
Description
Alarm
Indication
Functionality
On – A problem with the power amplifier or in
the locking process of any of the synthesizers
Off –Normal operation
12V IN
ETH
12V DC power
supply
On – 12VDC power is supplied to the unit
Ethernet
activity
Blinking – Data received from or transmitted to
Ethernet LAN
Off – 12VDC is not available
Off – No activity on the Ethernet LAN
Note: Verifying proper operation of the outdoor unit using the LEDs as described
above is possible only after completion of the configuration process.
BreezeACCESS MMDS Series
21
BS Equipment Installation Manual
Specifications
5. SPECIFICATIONS
5.1 Radio
Frequency
2.500GHz –2.686GHz
Radio Access Method
FH-CDMA or TDMA
Operation Mode
Time Duplex Division
Channel Bandwidth
2 MHz
Output Power (at antenna port)
29 dBm typical. Power Control range – 20 dB
Sensitivity
-6
(dBm at antenna port, BER 1E10 )
1Mbps
2Mbps
3Mbps
-93
-86
-77
Data Rate
3Mbps max
Modulation
Multilevel GFSK
5.2 Outdoor Unit to Indoor Unit Communication
IF Frequency
440 MHz
IF cable Impedance
50 ohm
Maximum IF cable Attenuation
15dB
Maximum IF cable DC Resistance
1.5 ohm
BS Equipment Installation Manual
22
BreezeACCESS MMDS Series
Specifications
5.3 Configuration and Management
Local Management
Via MON port, Monitor program using terminal
emulation
Remote Management
SNMP, Telnet, TFTP
Remote Management Access
From Wired LAN, Wireless Link
SNMP Agents
MIB II, Bridge MIB, Private MIBs
Security
Authentication and filtering
Software upgrade
TFTP download
5.4 Interfaces
Interface
Outdoor Unit
RF (AU-E)
N-Type jack lightning
protected
IF
TNC jack, lightning
protected
Indoor Equipment
TNC jack, lightning protected
Ethernet
10BaseT (RJ-45) with two embedded LEDs
Monitor
3 pin low profile
Power
12 VDC via the IF cable
4-pin power connector (BS-PS),
DC plug for the AU-PS power supply (AU-NI)
BreezeACCESS MMDS Series
23
BS Equipment Installation Manual
Specifications
5.5 Electrical
Outdoor Unit
12 VDC via the IF cable
Indoor Modular Shelf Equipment
-48 VDC, 200 W for a fully equipped shelf.
AU (Indoor + Outdoor): 25W
Indoor AU-NI Unit
AU-NI: 12VDC/2.5A from AU-PS
AU-PS: 100 - 240 VAC, 47-63 Hz
5.6 Mechanical
Outdoor Unit
AU-RE: 30cm x 12cm x 5cm, 2.2 kg.
AU-RA: Depending on specific model.
Indoor Modular Shelf Equipment
BS-SH: 19”,3U, depth 26cm, 6 kg. Fully loaded
Indoor AU-NI Unit
AU-NI: 13cm x 8.6cm x 3cm, 0.5 kg.
AU-PS: 10cm x 6.5cm x 3.5cm, 0.4 kg.
5.7 Environmental
Outdoor Unit
Indoor Equipment
Operating Temperature
-400C to 600C
00C to 450C
Operating Humidity
5%-95% non condensing
Weather protected
5%-95% non condensing
5.8 Standards Compliance, General
EMC
FCC part 15, FCC part 21
Safety
UL 1950
Environmental
GR - 63 - CORE (Bellcore)
BS Equipment Installation Manual
24
BreezeACCESS MMDS Series
Specifications
APPENDIX A. USING TELNET
Use the following procedure to connect to BreezeACCESS 3.5 units via a Telnet
session.
1. Connect the PC to the Ethernet port of the unit (or the hub to which the unit
is connected) using a straight Ethernet cable. If you connect the PC directly
to a unit that is normally connected to a hub, use a crossed Ethernet cable.
You may also connect the PC to any Ethernet port on the network and
communicate with the unit to be managed via the wired or wireless media.
2. Make sure that the IP parameters of the PC are configured to enable
connectivity with the unit.
3. Run a Telnet application and use the IP address of the unit to be managed as
the Host Name.
4. Set Port to Telnet (this is the default).
5. Set Terminal Type to VT100 (this is the default).
6. Enter the Service Provider password.
7. When the password is recognized, the following message is displayed:
You have entered.
8. Press Enter, the Breeze ACCESS Monitor is displayed on the screen.
9. To exit the Telnet session, choose Disconnect from the Connect menu.
(The session is terminated automatically, after a specific time of inactivity
determined by the Log-out Timer).
BreezeACCESS MMDS Series
25
BS Equipment Installation Manual
Appendix B
APPENDIX B. MMDS CHANNELS AND
FREQUENCIES
Channel
Name
Frequency
Band (MHz
Low Frequency (MHz)
High Frequency (MHz)
Actual
Value in
Add/Delete
Sub-bands
menu
Actual
Value in
Add/Delete
Sub-bands
menu
A1
2500 - 2506
2501.5
2501
2504.5
2504
B1
2506 - 2512
2507.5
2507
2510.5
2510
A2
2512 - 2518
2513.5
2513
2516.5
2516
B2
2518 - 2524
2519.5
2519
2522.5
2522
A3
2524 - 2530
2525.5
2525
2528.5
2528
B3
2530 - 2536
2531.5
2531
2534.5
2534
A4
2536 - 2542
2537.5
2537
2540.5
2540
B4
2542 - 2548
2543.5
2543
2546.5
2546
C1
2548 - 2554
2549.5
2549
2552.5
2552
D1
2554 - 2560
2555.5
2555
2558.5
2558
C2
2560 - 2566
2561.5
2561
2564.5
2564
D2
2566 - 2572
2567.5
2567
2570.5
2570
C3
2572 - 2578
2573.5
2573
2576.5
2576
D3
2578 - 2584
2579.5
2579
2582.5
2582
BS Equipment Installation Manual
26
BreezeACCESS MMDS Series
Appendix B
Channel
Name
Frequency
Band (MHz
Low Frequency (MHz)
High Frequency (MHz)
Actual
Value in
Add/Delete
Sub-bands
menu
Actual
Value in
Add/Delete
Sub-bands
menu
C4
2584 - 2590
2585.5
2585
2588.5
2588
D4
2590 - 2596
2591.5
2591
2594.5
2594
E1
2596 - 2602
2597.5
2597
2600.5
2600
F1
2602 - 2608
2603.5
2603
2606.5
2606
E2
2608 - 2614
2609.5
2609
2612.5
2612
F2
2614 - 2620
2615.5
2615
2618.5
2618
E3
2620 - 2626
2621.5
2621
2624.5
2624
F3
2626 - 2632
2627.5
2627
2630.5
2630
E4
2632 - 2638
2633.5
2633
2636.5
2636
F4
2638 - 2644
2639.5
2639
2642.5
2642
G1
2644 - 2650
2645.5
2645
2648.5
2648
H1
2650 - 2656
2651.5
2651
2654.5
2654
G2
2656 - 2662
2657.5
2657
2660.5
2660
H2
2662 - 2668
2663.5
2663
2666.5
2666
G3
2668 - 2674
2669.5
2669
2672.5
2672
H3
2674 - 2680
2675.5
2675
2678.5
2678
G4
2680 - 2686
2681.5
2681
2684.5
2684
BreezeACCESS MMDS Series
27
BS Equipment Installation Manual

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Create Date                     : 1910:00:80 20:82:85
Producer                        : Acrobat Distiller 3.0 for Windows
Creator                         : PSCRIPT.DRV Version 4.0
Title                           : Microsoft Word - BST 2.5 _27.
Modify Date                     : 2000:09:11 11:45:15-07:00
Page Count                      : 35

EXIF Metadata provided by EXIF.tools