Amazon com Services 0610 Wireless Remote Controller User Manual
Fleisher Gromes LLC Wireless Remote Controller
Contents
User manual
2: Download the Device app
www.XXXXXX.com/start
The app enables you to set up and
manage the Device on your
phone or tablet. Opening the app
will immediately start the setup
process. During setup, you will
connect Device to the Internet.
You may need your Wi-Fi
password.
1. Plug in Device
Plug the included power cable into
Device and then into a power
outlet. A blue light ring will begin
to spin around the top. In about a
minute, the light ring will change
to
orange and the Device will
greet you.
User's Guide for
FCC ID: ZWJ-0823 &
FCC ID: 2ACBD-0610
Doppler
Action button: Instead of using
the wake word, press this button
to wake up Device or to turn off
the alarm and timer. To set up Wi-
Fi, press this button for five
seconds.
Microphone on/off button: Press
this button to turn the microphone
on and off. When the light ring is
red, Device cannot hear you.
Light ring: The color of the light
ring indicates what Device is doing.
Blue indicates start-up mode (1 to 3
minutes) and orange indicates Wi-Fi
setup mode. Go to the app to learn
more about the other colors.
Volume ring: Turn the dial clockwise
to increase the volume. The light
ring fills in as the volume increases.
Power LED: A small white
indicator light displays when Device
is plugged in.
Device Overview
Action button
Microphone on/off
Light ring
Volume ring
Power LED
Legal and Compliance Information
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
-This device may not cause harmful interference.
-This device must accept any interference received, including
interference that may cause undesired operation.
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected. -Consult the dealer or an experienced
radio/TV technician for help.
Changes or modification not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
The Devices meet the FCC Radio Frequency Emission Guidelines and are
certified with the FCC as the FCC ID number found on the back of the
Device.
Information Regarding Exposure to Radio Frequency Energy
Your Device is designed and manufactured not to exceed the emission limits
for exposure to RF energy set by the Federal Communications Commission
of the United States (FCC). This device should be installed and operated
with minimum distance 20cm between the radiator & your body. For the
remote controller, it meets the RF exposure requirement of low power
devices under portable operation. Information on your Device is on file with
the FCC and can be found under the Display Grant section of http://
transition.fcc.gov/oet/ea/ after searching on the FCC ID for your Deivce,
which can be found on the product label.
You can talk to Device
just using your voice. The
remote is provided to help
you when using Device in
a loud setting.
Microphone
Volume up
Volume down
AAA batteries
Previous
Next
Play/Pause
Talk button
Device Remote
Pairing the remote
to your Device
Remote holder
Insert the included
batteries into the
remote. It will
automatically pair with
Device during setup.
If this is a replacement
remote, go to Settings
in the Device app. Select
your Device, click Add a
remote, and follow the
instructions there.
The remote holder easily
attaches to magnetic
surfaces, or use the
included adhesive
to attach it to other
surfaces.