Amtran Technology Co SV422XVT-BT Bluetooth Embedded Module User Manual Rev 02
Amtran Technology Co Ltd Bluetooth Embedded Module Rev 02
User Manual Rev 02
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1157727 |
| Application ID | OnW5bBT9FNyfsRDAuwftZw== |
| Document Description | User Manual Rev 02 |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 19.71kB (246338 bits) |
| Date Submitted | 2009-08-24 00:00:00 |
| Date Available | 2009-08-24 00:00:00 |
| Creation Date | 2008-12-14 19:55:32 |
| Producing Software | Toolkit http://www.activepdf.com |
| Document Lastmod | 2009-08-21 15:00:12 |
| Document Title | User Manual Rev 02 |
| Document Creator | Toolkit http://www.activepdf.com |
CO RP RA TI BCM92046MD_EMB User Manual CO FI DE TI AL FO AM TR AN TE CH LO Bluetooth® Embedded Module 92046MD-UM100-R 5300 California Avenue • Irvine, CA 92617 • Phone: 949-926-5000 • Fax: 949-926-5203 12/14/2008 EDSCE 12/05/08 User Manual BCM92046MD_EMB TI 12/05/08 RA S e c t i on 1 : O v e r v i ew RP INTRODUCTION CO The BCM92046MD_EMB is a Bluetooth ® embedded module based on the BCM2046 Bluetooth 2.1 specification-compliant stand-alone baseband processor with an integrated 2.4 GHz transceiver. It is fully compliant with the Bluetooth radio specification and incorporates new modulation schemes to support enhanced data rates (EDRs) of 2 Mbps and 3 Mbps. The BCM92046MD_EMB module supports both UART and Universal Serial Bus (USB) version 2.0 full-speed interfaces, and is fully compatible with the HCI interface specification. The module includes EEPROM, a crystal, and a Printed Circuit Board (PCB) antenna. LO FEATURES Secure Simple Pairing (SSP) Link Supervision Time Out (LSTO) Encryption Pause Resume (EPR) Enhance Inquiry Response (EIR) Sniff Subrating (SSR) Erroneous Data (ED) Packet Boundary Flag (PBF) TE CH A Bluetooth 2.1 compliant embedded USB module with the following features: AN • The module supports the following features: A Programmable collaborative coexistence interface • Class 1 output power capability • Class 2 RF maximum output power specification of 4 dBm • Full piconet and scatternet operation • EDR rates of 2 MBps and 3 MBps • A high-speed UART interface • A USB 2.0 full-speed compliant interface • Built-in Low Power Oscillator (LPO) clock or operation using an external LPO clock • Full support for power-saving modes. • Advanced Audio Distribution Profile (A2DP) • Upgradeable firmware through an EEPROM download • A PCB antenna CO FI DE TI AL FO AM TR • B roadc om C or por ati on Document 92046MD-UM100-R Overview 12/14/2008 EDSCE Page 1 User Manual 12/05/08 RA TI PHYSICAL DESCRIPTION MODULE PINOUT CO RP The BCM92046MD_EMB is a 27.6 mm × 14.6 mm FR4 PCB with a maximum thickness of 0.925 mm (36.4 mil) and 31 pads located around the perimeter. Figure 3 shows the module pinout diagram. 27.6 mm AM TR AN TE CH 14.6 mm LO Pin 1 Pin 31 CO FI DE TI AL FO Figure 3: 2046MD_EMB Pinout B roadc om C or por ati on Page 4 BCM92046MD_EMB Physical Description Document 12/14/2008 EDSCE 92046MD-UM100-R User Manual BCM92046MD_EMB 12/05/08 TI MODULE PINOUT DESCRIPTION RA Table 1 shows the BCM92046MD_EMB pinout description. GPIO_1 11 SCL 12 SDA 14 15 16 17 19 UART_RXD UART_TXD UART_RTS UART_CTS GPIO_3 20 GPIO_4 3.3V power supply to the module Pre-regulator and VREG1 enable/disable control Active low system reset GPIO AN TR GPIO_6 AM 21 22 24 FO 25 GPIO_5 USB_DN USB_DP CO RP Power Input Input Input/ Output Input/ Output Input/ Output Input/ Output Input/ Output Input Output Output Input Input/ Output Input/ Output Input/ Output Input/ Output Input/ Output Input/ Output GPIO GPIO 10 System ground LO GPIO_2 Power TE Description 1, 2, 3, 5, 13, 18, 23, 26, 27, 28, 29, GND 30, 31 3.3V VREG_CTL RST_N GPIO_0 I/O Broadcom serial control clock (I2C compatible) Pin Name Broadcom serial data (I2C compatible) CH Pin Table 1: Pinout Description UART serial input UART serial output UART request to send UART clear to send GPIO GPIO GPIO GPIO Downstream USB differential data Downstream USB differential data AL APPLICATION CODE TI Application code resides in the on-module EEPROM. During power-on reset, the application code must be downloaded to BCM2046 RAM before the board performs any Bluetooth activity. The 2046 on-chip serial port can be used to download application code from a host computer file to EEPROM or on-chip RAM using either the UART or USB transport mechanisms. CO FI DE Application code can also be patched directly to BCM2046 RAM from the host during power-on reset without an external EEPROM. B roadc om C or por ati on Document 92046MD-UM100-R Application Code 12/14/2008 EDSCE Page 5 User Manual 12/05/08 RA TI MODULE RF SPECIFICATIONS AND MEASUREMENTS RP Table 3, Table 4 on page 19, and Table 5 on page 21 show the Class 2 RF specifications and measurements as referenced to the module’s RF input/output port without the PCB antenna (that is, all measurements are conducted not radiated). Parameter Measurement Data Criteria Frequency Minimum Maximum (MHz) Measurement – –6 Units 1.84 (Pavg min.) dBm 1.85 (Pavg max.) 2.09 (Peak) • • • • DH5 packet Hopping on Loopback Number of packets = 10 2441 1.44 (Pavg min.) 1.45 (Pavg max.) 1.77 (Peak) 2480 0.61 (Pavg min.) 0.62 (Pavg max.) 1.03 (Peak) .87 dBm per 100 kHz EIRP • • • • DH5 packet Hopping off Loopback Number of packets = 10 MHz • • • • Payload = Tx DH1 packet PRBS9 Tx power [dBm] = 1.00 MHz • • • • DH5 packet Hopping off Loopback; Number of packets = 10 dBm • • • • DH5 Hopping Off Loopback Number of packets = 10 LO 2402 Output power Conditions Transmitter CO Table 3: Module Class 2 GFSK RF Specification (T = 25°C) Specification – – 20 – Tx output spectrum frequency range – 2400 2483.5 2402 2401.23 2480 2480.7 Tx output spectrum 20 dB bandwidth – Tx output spectrum, adjacent channel power |M-N| = 2 AM |M-N| ≥ 3 – FO Exceptions – –40 TE AN –20 2402 .92 2441 .92 2480 .92 2405 –54.09 2441 –54.32 2477 –55.09 2405 –56.96 2441 –49.38 2477 –49.35 2405 2441 2477 2405 2441 2477 dBm – – CO FI DE TI AL Fails TR CH Power density B roadc om C or por ati on Page 16 Module RF Specifications and Measurements Document 12/14/2008 EDSCE BCM92046MD_EMB 92046MD-UM100-R User Manual BCM92046MD_EMB 12/05/08 140 Delta f2 / Delta f1 0.8 –75 – 75 136 2480 139.1 2402 151.9 2441 149.3 2480 148.1 2402 .94 2441 .98 • • • kHz RA kHz 132.8 DH5 Loopback Number of packets = 10 Change payload = Toggle payload = Continue. – 2480 1.01 2402 –16.8 (Minimum) kHz –15.5 (Average) –13.8 (Maximum) 2441 –16.1 (Minimum) kHz –15.0 (Average) –13.6 (Maximum) • • • Hopping on Number of packets = 10 Loopback • • • • DH1 and DH3 and DH5 Hopping on Number of packets = 10 Loopback • • • • • Hopping off Number of packets = 740 Payload = T Dirty TX = On Tx power = –70 dBm • • • Payload = Tx DH1 packet PRBS9 • Tx power [dBm] = 1.00 Initial carrier frequency tolerance 175 2402 2441 Delta f1(Avg) – Conditions Delta f2max ≥ 115 99.9% of all delta f2max Modulation Units RP Minimum Maximum Frequency Measurement (MHz) Criteria LO Parameter Measurement Data CO Specification TI Table 3: Module Class 2 GFSK RF Specification (T = 25°C) (Cont.) –25 Three slot packet –40 drift [DH3] – AM Drift rate –40 40 40 TR Five slot packet drift [DH5] 25 – 2402 –6 2441 –5 TE One slot packet drift [DH1] AN Carrier frequency drift –16.3 (Minimum) kHz –13.1(Average) –11.5 (Maximum) CH 2480 2480 –6 2402 –6 2441 –6 2480 –6 2402 –7 2441 –6 2480 –6 2402 5.33 2441 –4.79 2480 –6.03 2402 0.00E+00 2441 0.00E+00 kHz kHz kHz dB Receiver –70 dBm, single-slot packets – FO Sensitivity (BER) AL –70 dBm, – multislot packets Number of fails 0.1 Number of exceptions 2480 0.00E+00 2402 0.00E+00 2441 0.00E+00 2480 0.00E+00 2405 2441 2477 2405 2441 2477 BER BER – – CO FI DE TI C/I performance 0.1 B roadc om C or por ati on Document 92046MD-UM100-R Module RF Specifications and Measurements 12/14/2008 EDSCE Page 17 User Manual 12/05/08 TI Table 3: Module Class 2 GFSK RF Specification (T = 25°C) (Cont.) Measurement Data Criteria Minimum Maximum Frequency Measurement (MHz) Units Conditions Intermodulation performance IP3+5 – BER • • • • At –20 dBm input – – –70 2402 0.00E+00 2441 0.00E+00 2480 0.00E+00 2402 0.00E+00 2441 0.00E+00 2480 0.00E+00 2402 –87.83 2441 –88.59 2480 –88.36 BER BER dBm RP 0.00E+00 CO 2480 DH5 Hopping off Payload = Tx Dirty TX = Off • • • Payload = Tx Number of packets = 7408 Tx power = –20 dBm • • • • Hopping Off Number of packets = 7408 Payload = Tx Dirty TX = On CO FI DE TI AL FO AM TR AN TE CH Single-Slot Sensitivity Level Search 0.1 0.00E+00 0.1 0.00E+00 2441 Maximum input level (BER) – 2402 LO IP3-5 0.1 Parameter RA Specification B roadc om C or por ati on Page 18 Module RF Specifications and Measurements Document 12/14/2008 EDSCE BCM92046MD_EMB 92046MD-UM100-R User Manual BCM92046MD_EMB TI 12/05/08 Specification Criteria Minimum Freq. Maximum (MHz) EUT maximum relative transmit power –4 Units Conditions 2402 .05 (Minimum) .05(Average) .06 (Maximum) dB 2441 .06 (Minimum) .08 (Average) .09 (Maximum) dB 2480 .08 (Minimum) .10 (Average) .11 (Maximum) dB 2402 .11 (Minimum) .13 (Average) .14 (Maximum) dB 2441 .18 (Minimum) .19 (Average) .20(Maximum) dB Measurement Transmitter • 2-DH5 Hopping off Loopback EUT maximum and minimum Number of packets = 10 • • • • 2-DH5 Hopping off Loopback Number of packets = 200 • • • 2-DH1 Hopping off Number of packets = 100 • • • • 2-DH5 Hopping off Loopback EUT maximum • • • • • 2-DH5 Hopping off Payload = Tx Dirty TX = On Tx power = –70 dBm • • • • 2-DH5 Hopping off Payload = Tx Dirty TX = On CO • • • • dB – 100 (Minimum) 100(Maximum) – .11 (Minimum) .15 (Maximum) – – 99 – Peak DEVM – 0.35 RMS DEVM – 0.2 – .48 (Minimum) .68 (Maximum) Initial frequency error –75 75 – –16.8 (Minimum) kHz –13.4 (Maximum) Frequency error –10 10 – –1.3 (Minimum) –1.0 (Maximum) kHz Block frequency error –75 75 – –17.3 (Minimum) –13.8(Maximum) kHz – 2402 100 2441 100 % Good Packets EDR in-band spurious emission Number of fails TE AN 99 AM EDR differential phase encoding FO Number of exceptions CH 99% DEVM ≤ 0.30 TR EDR carrier frequency stability and modulation accuracy .23 (Minimum) .24 (Average) .25 (Maximum) 2480 LO –4 EUT minimum relative transmit power EDR relative transmit powers RP Parameter Measurement Data RA Table 4: Module Class 2 EDR RF 2 MBPS Specification (T = 25°C) 2480 100 2405 – 2441 – 2477 – 2405 – 2441 – 2477 – 2402 0.00E+00 BER 2441 0.00E+00 2480 0.00E+00 2402 – 2441 – 2480 – 2402 –90 2441 –90 2480 –90 AL Receiver Receive sensitivity level search 1.6e6 payload bits @ – – 70 dBm .00007 16e6 payload bits – @ –70 dBm, if a failure occurs in the first 1.6e6 bits .0001 EDR receiver 0.0001 BER sensitivity Level –70 – BER dBm CO FI DE TI EDR sensitivity (BER) B roadc om C or por ati on Document 92046MD-UM100-R Module RF Specifications and Measurements 12/14/2008 EDSCE Page 19 User Manual 12/05/08 TI Table 4: Module Class 2 EDR RF 2 MBPS Specification (T = 25°C) (Cont.) Measurement Data Parameter Criteria Minimum Freq. Maximum (MHz) Measurement Units Conditions EDR BER floor 8e6 payload bits @ –60 dBm – .000007 2402 0.00E+00 BER 2441 0.00E+00 2480 0.00E+00 2402 – 2441 – Number of exceptions EDR maximum input level 1.6e6 payload bits @ –20 dBm – .001 – – 2441 – 2477 2405 2441 2477 2402 0.00E+00 2441 0.00E+00 – RP • • • • 3-DH5 Hopping Off Payload = Tx Dirty TX = Off • • • • 2-DH5 Hopping off Payload = Tx Tx power = –20 dBm – 0.00E+00 – – BER CO FI DE TI AL FO AM TR AN TE CH 2480 2-DH5 Hopping off Payload = Tx Dirty TX = Off T x power = –60 dBm CO 2480 2405 BER LO Number of fails .00001 – EDR C/I performance 160e6 payload bits @ –60 dBm, if a failure occurs in the first 8e6 bits • • • • • RA Specification B roadc om C or por ati on Page 20 Module RF Specifications and Measurements Document 12/14/2008 EDSCE BCM92046MD_EMB 92046MD-UM100-R User Manual BCM92046MD_EMB TI 12/05/08 Specification Freq. Minimum Maximum (MHz) Measurement Units Conditions 2402 .04 (Minimum) .05(Average) .06 (Maximum) dB • 2441 .05 (Minimum) .06 (Average) .07 (Maximum) dB 2480 .08 (Minimum) .10 (Average) .10 (Maximum) dB 2402 .10 (Minimum) .12 (Average) .14 (Maximum) dB 2441 .14 (Minimum) .14 (Average) .16(Maximum) dB Criteria or Condition Transmitter –4 • 3-DH5; Hopping off; Loopback; EUT maximum and minimum Number of packets = 10 • • • • 3-DH5 Hopping off Loopback Number of packets = 200 • • • 3-DH1 Hopping Off Number of packets = 100 • • • • 3-DH5 Hopping off Loopback EUT maximum • • • • • 3-DH5 Hopping off Payload = Tx Dirty TX = On Tx power = –70 dBm • • • • 3-DH5 Hopping off Payload = Tx Dirty TX = On CO EUT maximum relative transmit power .17 (Minimum) .19 (Average) .20(Maximum) dB – 100 (Minimum) 100(Maximum) – .13 (Minimum) .17 (Maximum) – – 2480 LO –4 EUT minimum relative transmit power EDR relative transmit powers RP Parameter Measurement Data RA Table 5: Module Class 2 EDR RF 3MBPS Specification (T = 25°C) – 0.25 RMS DEVM – 0.13 – .05 (Minimum) .067 (Maximum) Initial frequency error –75 75 – –17.1 (Minimum) kHz –13.0 (Maximum) Frequency error –10 10 – –1.7 (Minimum) –1.2 (Maximum) Block frequency error –75 75 – –17.6 (Minimum) kHz –13.9(Maximum) – 2402 100 2441 100 TE 99 AM % Good Packets EDR in-band Number of fails spurious emission FO Number of exceptions CH – TR EDR differential phase encoding 99 AN EDR carrier 99% DEVM frequency stability ≤ 0.30 and modulation Peak DEVM accuracy kHz 2480 100 2405 – 2441 – 2477 – 2405 – 2441 – 2477 – 2402 0.00E+00 BER 2441 0.00E+00 AL Receiver 1.6e6 payload bits @ –70 dBm – 16e6 payload bits @ –70 dBm, if a failure occurs in the first 1.6e6 bits – Receive sensitivity EDR receiver 0.0001 level search BER sensitivity level – .00007 .0001 –70 2480 0.00E+00 2402 – 2441 – 2480 – 2402 –84.32 2441 –84.49 2480 –84.26 BER dBm CO FI DE TI EDR sensitivity (BER) B roadc om C or por ati on Document 92046MD-UM100-R Module RF Specifications and Measurements 12/14/2008 EDSCE Page 21 User Manual 12/05/08 2402 0.00E+00 BER 2441 0.00E+00 • • • • • Number of fails 1.6e6 payload bits @ –20 dBm – .001 0.00E+00 2402 – 2441 – BER 2480 – 2405 – 2441 – 2477 – 2405 2441 2477 2402 0.00E+00 2441 0.00E+00 • • • • 2-DH5 Hopping off Payload = Tx Dirty TX = Off • • • • 3-DH5 Hopping off Payload = Tx Tx power = –20 dBm – – – 0.00E+00 BER CO FI DE TI AL FO AM TR AN TE CH 2480 RP .00001 2480 3-DH5 Hopping off Payload = Tx Dirty TX = Off T x power = –60 dBm CO .000007 RA – 160e6 payload bits – @ –60 dBm, if a failure occurs in the first 8e6 bits Number of exceptions EDR maximum input level Conditions EDR C/I performance Units 8e6 payload bits @ –60 dBm Measurement LO EDR BER floor Freq. Minimum Maximum (MHz) Criteria or Condition Measurement Data Parameter TI Table 5: Module Class 2 EDR RF 3MBPS Specification (T = 25°C) (Cont.) Specification B roadc om C or por ati on Page 22 Module RF Specifications and Measurements Document 12/14/2008 EDSCE BCM92046MD_EMB 92046MD-UM100-R User Manual BCM92046MD_EMB TI 12/05/08 RA S e c t io n 3 : O rd e r i n g I nfo r m a t io n Contact your Broadcom representative for a BCM92046MD_EMB kit. See Table 6 for ordering information. Part Number BCM92046 Bluetooth Embedded Module BCM92046MD_EMB CO FI DE TI AL FO AM TR AN TE CH LO Description CO RP Table 6: Ordering Information B roadc om C or por ati on Document 92046MD-UM100-R Ordering Information 12/14/2008 EDSCE Page 23 Declaration of Conformity Label & Marking Requirements This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. FCC Caution: The user is cautioned that any changes or modifications not expressly approved by Renishaw plc, or authorised representative could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Page Count : 13 Page Mode : UseOutlines Has XFA : No XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:6788805d-2006-4e5f-8df4-22f96223d3b9 Producer : Toolkit http://www.activepdf.com Aptkver : 3.5.2 SP6 (5208) Modify Date : 2009:08:21 15:00:12+08:00 Create Date : 2008:12:14 19:55:32Z Creator Tool : Toolkit http://www.activepdf.com Metadata Date : 2009:08:21 15:00:12+08:00 Document ID : uuid:df683071-2b11-43cf-9bca-a2bde2b25f12 Instance ID : uuid:ec4fe237-6e4c-49a8-9ce1-db3367febfdf Format : application/pdf Creator : Toolkit http://www.activepdf.com APTKVER : 3.5.2 SP6 (5208)EXIF Metadata provided by EXIF.tools