Andrew Wireless Innovations Group RPT-MR801BI MR801BI Power and MR801BI SMR Band Repeater User Manual M0079A1A

Download:
Mirror Download [FCC.gov]
Document ID	125969
Application ID	ibD0kRDJc0KV2u+1tJLEGw==
Document Description	Users manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	304.01kB (3800130 bits)
Date Submitted	2000-11-20 00:00:00
Date Available	2000-11-16 00:00:00
Creation Date	0000-00-00 00:00:00
Producing Software	Acrobat PDFWriter 3.02 for Windows
Document Lastmod	0000-00-00 00:00:00
Document Title	M0079A1A.PDF
Document Creator	Microsoft Word
Document Author:	Unknown

User’s manual for Repeater MRx01B Power
User’s manual for
band or channel selective Repeater
MRx01B Power
M0079A1A.doc
Id.-No. 151775
Page 1
10-March-00
User’s manual for Repeater MRx01B Power
Copyright  MIKOM, Buchdorf 2000
All rights reserved.
No parts of this publication may be
reproduced, stored in a retrieval system, transmitted in any form or by
any means, electronical, mechanical photocopying,
recording or otherwise, without prior written permission of the
publisher.
M0079A1A.doc
Id.-No. 151775
Page 2
10-March-00
User’s manual for Repeater MRx01B Power
Table of Contents
LIST OF FIGURES AND TABLES
LIST OF UNIT SPECIFIC ABBREVIATIONS
CONTENTS OF DELIVERY
HEALTH AND SAFETY WARNING
PREAMBLE
INTRODUCTION
11
1.1
Intended purpose
11
1.2
About the MRx01B Power
11
1.3
Modular design
11
1.4
Applications
12
FUNCTIONAL DESCRIPTION
13
2.1
General
13
2.2
Conversion modules
14
2.3
Mother board
14
2.4
Control module SM 2009 ( Rev. 07 and higher )
16
2.5
Duplexer
20
2.6
Active combiner
21
2.7
Measuring aids
21
2.8
Feedforward amplifier
22
2.9
Power supply
22
3.1
FUNCTIONS AND FEATURES
24
Band and channel selectivity
24
M0079A1A.doc
Id.-No. 151775
Page 3
10-March-00
User’s manual for Repeater MRx01B Power
3.2
Gain setting
24
3.3
ALC
25
3.4
CFO
25
3.5
BITE and alarms
3.5.1
Handling of alarms
3.5.2
Status report
3.5.3
Severity levels
25
27
28
28
29
OPTIONAL EQUIPMENT
4.1
VSWR module
29
4.2
External alarms
29
4.3
Modem
30
4.4
External RF output
31
4.5
Battery backup module
32
5.1
INSTALLATION
33
Mechanical installation
34
5.2
Electrical installation
5.2.1
Grounding
5.2.2
Power connection
5.2.3
Connection of the antenna cables
36
36
37
37
39
6.1
SETTING TO WORK
Preparation
39
6.2
Setting of operational parameters
6.2.1
Manual settings by means of rotary switches
6.2.2
Setting of the attenuation
6.2.3
Settings via personal computer as terminal
6.2.4
Settings via modem
39
40
40
42
44
TROUBLE SHOOTING
45
7.1
Error indication
45
7.2
Alarm monitoring with the STATUS HIST command
45
M0079A1A.doc
Id.-No. 151775
Page 4
10-March-00
User’s manual for Repeater MRx01B Power
7.3
Power supply
46
7.4
General remarks
46
MAINTENANCE
47
8.1
General
47
8.2
Replacement of the fuses (mains)
47
8.3
Replacement of the power supply fuse
48
8.4
Replacement of the mains cable
48
8.5
Replacement of the RAM / RTC battery
49
8.6
Replacement of the duplexers
50
8.7
Replacement of conversion modules
50
8.8
Replacement of the control module SM 2009
53
8.9
Replacement of power supplies
54
8.10
Replacement of active combiner modules
55
8.11
Replacement of feedforward amplifier
55
9.1
APPENDICES
58
Repeater specifications
58
9.2
Spare parts lists for MRx01B Power
9.2.1
Spare parts list for MR301B Power
9.2.2
Spare parts list for MR401B Power
9.2.3
Spare parts list for MR701B Power
9.2.4
Spare parts list for MR801B Power and MR801Bi Power
68
68
70
71
73
9.3
Installation drawing of the Repeater
75
9.4
Top view of the Repeater (left side , exemplary configuration)
76
9.5
Top view of the Repeater (right side, exemplary configuration)
77
9.6
One channel configuration – cabling and block diagram
78
10
INDEX
M0079A1A.doc
80
Id.-No. 151775
Page 5
10-March-00
User’s manual for Repeater MRx01B Power
LIST OF FIGURES AND TABLES
table 1-1 List of international sales offices .............................................................................. 10
figure 2-1 Block diagram of MRx01B Power.......................................................................... 13
figure 2-2 Top view of a conversion module ........................................................................... 14
figure 2-3 Top view of a mother board .................................................................................... 15
figure 2-4 Configuration of the control module ( Rev.07 and higher ) .................................... 18
figure 2-5 Configuration of the DIP-Switches ......................................................................... 19
figure 2-6 Top view of the duplexers ....................................................................................... 20
figure 2-7 Top view of the active combiner module ................................................................ 21
figure 2-8 Top view of the feedforward amplifier ................................................................... 22
figure 2-9 Mounting position of power supplies...................................................................... 23
figure 2-10 ON / OFF position of external switch ................................................................... 23
figure 3-1 Position of rotary switches ...................................................................................... 24
table 3-2 List of all available alarms ........................................................................................ 26
figure 4-1 Clamps for external alarms...................................................................................... 29
figure 4-2 Modem kit ............................................................................................................... 31
figure 4-3 Position of external RF output................................................................................. 31
figure 4-4 Mounting position of batteries ................................................................................ 32
figure 5-1 System description .................................................................................................. 33
figure 5-2 Top view and clearance distance............................................................................. 34
figure 5-3 Wall mounting brackets........................................................................................... 35
figure 5-4 Grounding kit .......................................................................................................... 36
figure 5-5 Screw terminal......................................................................................................... 37
figure 5-6 Connector panel layout............................................................................................ 38
table 6-1 LED indication .......................................................................................................... 39
figure 6-2 Position of the DIP-Switch 1 and 2 and RAM/RTC battery ................................... 40
figure 6-3 Position of the rotary switches ................................................................................ 41
figure 6-4 Rotary switches and label........................................................................................ 41
table 6-5 DIP-switch configuration .......................................................................................... 42
table 6-6 List of AT commands................................................................................................ 44
figure 8-1 Position of power supply fuse ................................................................................. 48
figure 8-2 External filter at iDEN module................................................................................ 51
figure 8-3 Top view of a conversion module ........................................................................... 51
figure 8-4 Position of hex-coded rotary switches..................................................................... 52
table 8-5 Address of synthesizer .............................................................................................. 52
table 8-6 Adress of synthesizer, conversion modules .............................................................. 52
figure 8-7 Position of hex-coded rotary switches..................................................................... 52
figure 8-8 Position of control module ...................................................................................... 53
figure 8-9 Power supply ........................................................................................................... 54
figure 8-10 Position of special-nut M4 .................................................................................... 54
figure 8-11 Position of counter sunk screws on active combiner............................................. 55
figure 8-12 Position of feedforward amplifier reset board....................................................... 56
figure 8-13 Position of feedforward amplifiers........................................................................ 57
figure 9-1 Installation drawing of the Repeater........................................................................ 75
figure 9-2 Top view of the Repeater (left side, exemplary configuration)............................... 76
figure 9-3 Top view of the Repeater (right side, exemplary configuration) ............................ 77
figure 9-4 Cabling of one channel Repeater............................................................................. 78
figure 9-5 Block diagram of one channel Repeater.................................................................. 79
M0079A1A.doc
Id.-No. 151775
Page 6
10-March-00
User’s manual for Repeater MRx01B Power
LIST OF UNIT SPECIFIC ABBREVIATIONS
ALC
BCCH
BITE
BTS
DL
ETS
Id.-No.
I²C-Bus
LMT
MR
OMC
PABX
PCMCIA
PSTN
Rev
RF
RLP
RSSI
RTC
SDA
SCL
UL
UPS
VSWR
Automatic Level Control
Broadcast Control Channel
Built In Test Equipment
Base Transceiver Station
Downlink
European Telecommunication Standard
Ident Number
Inter Integrated Circuit Bus (Philips)
Local Maintenance Timeout
MIKOM Repeater
Operation and Maintenance Centre
Private Automatic Branch Exchange
Personal Computer Modem Communication International Association
Public Switched Telephone Network
Revision
Radio Frequency
Radio Link Protocol
Receive Signal Strength Indication
Real Time Clock
Serial Data Line of I²C-Bus
Serial Clock Line of I²C-Bus
Uplink
Uninterruptable Power Supply
Voltage Standing Wave Ratio
CONTENTS OF DELIVERY
Qty
Repeater MRx01B Power
Qty
User’s manual for Repeater MRx01B Power
Qty
Software manual
Qty
Set of test protocols consisting of an electrical acceptance test protocol
and a safety test protocol applying to the power supply
Qty
Spare parts kit
Qty
Wall mounting kit
M0079A1A.doc
Id.-No. 151775
Page 7
10-March-00
User’s manual for Repeater MRx01B Power
HEALTH AND SAFETY WARNINGS
F Note:
F Note:
F Note:
F Note:
F Note:
M0079A1A.doc
The electrical installation has to be performed in accordance with the safety
regulations of the local authorities. Due to safety reasons the electrical
installation must be performed by qualified personnel. The cover of this unit
should not be opened while power is applied. Subsequent installation,
commissioning and maintenance activities that require the unit to be
powered with the cover open shall only be carried out by suitably qualified
personnel.
The grounding of the Unit has to be performed by all means. A grounding
bolt is provided at the cabinet in order to connect the earth bonding cable.
The Unit is heavy-weight. Make sure that a suitable mounting surface is
used. Only adequate manpower is allowed to handle the system.
ESD precautions have to be observed! Before maintenance work use the
available grounding system to connect ESD protection measures.
Due to power dissipation the Repeater may heat up the air volume inside the
cabinet and reach a very high temperature. Therefore the Repeater must be
mounted in the vertical plane to a wall or a mast without additional
enclosure to provide sufficient ventilation. Between the housing and the wall
a minimum distance must be kept in order to provide air circulation.
Id.-No. 151775
Page 8
10-March-00
User’s manual for Repeater MRx01B Power
PREAMBLE
The MRx01B Power manual ( Ordering number Id.-No. 151775 ) includes the following
parts:
Chapter 1: Introduction
Chapter 2: Functional description
Chapter 3: Functions and features
Chapter 4: Optional equipment
Chapter 5: Installation
Chapter 6: Setting to work
Chapter 7: Trouble shooting
Chapter 8: Maintenance
Chapter 9: Appendices
Chapter 10: Index
Any intervention has to be performed by authorized persons only. If you need technical
assistance with the Repeater MRx01B Power approach your local sales office or Mikom
directly.
MIKOM GmbH
Industriering 10
86675 Buchdorf
Germany
Tel: +49 (0) 9099 6 90
Fax: +49 (0) 9099 69 31
email: sales@mikom.com
http://www.mikom.com
Under consideration of all references given in this manual, the Repeater should be taken into
service without any complications and should operate trouble-free for a long time.
M0079A1A.doc
Id.-No. 151775
Page 9
10-March-00
User’s manual for Repeater MRx01B Power
LIST OF INTERNATIONAL SALES OFFICES
Allen Telecom Inc.
Allen Telecom Pty Ltd
Forem France
30500 Bruce Industrial Parkway 6 Stuart Street
Cleveland, Ohio 44 139-3996
Padstow NSW 2211
USA
Australia
Z.I. des Ebisoires
78370 Plaisir
France
Phone: +1 ( 440 ) 349-8400
FAX: +1 ( 440 ) 349-8407
Phone: +61 ( 2 ) 9774-4200
FAX: +61 ( 2 ) 9774-4500
Phone: +33 ( 1 )30-79-15-30
FAX: +33 ( 1 ) 30-55-55-37
FOREM S.p.A.
AT Singapore
AT China
Via Archimede N. 22/24
20041, Agrate Brianza
Milan
Italy
80 Marine Parade Road
#19-1 Parkway Parade
Singapore 449269
CITIC Building, # 11-04
19 Jianguomenwai Avenue
Beijing
China 100004
Phone: +39 ( 039 )605-41
FAX: +39 ( 039 ) 605-4477
Phone: +65 ( 345 ) 8022
FAX: +65 ( 345 ) 8033
Phone: +86 ( 10 ) 6508-3088
FAX: +86 ( 10 )6508-3066
AT Canada
FOREM UK
AT Hong Kong
1815 Ironstone Manor, # 12
Pickering, Ontario L1W 3W9
Canada
Unit D
Castle Industrial Park
Pear Tree Lane
Newbury, Berkshire
U.K. RG 14 2EZ
1603 Remington Center,
23 Hung To road,
Kwun Tong, Kowloon
Hong Kong
Phone: +1 ( 905 ) 839-3474
FAX: +1 ( 905 ) 839-4663
Phone: +44 ( 1635 ) 569-695 Phone: +852 ( 2389 ) 1844
FAX: +44 ( 1635 ) 569-463 FAX: +852 ( 2389 ) 4864
AT India
MIKOM Switzerland
MIKOM Austria
B-256 Ground Floor.
Chittaranjan Park
New Delhi 110019
Tiergartenweg 1
4710 Balzthal
Switzerland
Himbergerstr. 7/3/1
2320Schwechat
Austria
Phone: +91 ( 11 ) 696-3918
FAX: +91 ( 11 ) 652-1648
Phone: +41 ( 6238 ) 61260
FAX: +41 ( 6238 ) 61261
Phone: +43 ( 1 ) 706 - 3999
FAX: +43 ( 1 ) 706 - 39999
table 1-1 List of international sales offices
M0079A1A.doc
Id.-No. 151775
Page 10
10-March-00
User’s manual for Repeater MRx01B Power
1 Introduction
1.1
Intended purpose
Cellular telephone systems transmit signals in two directions between base stations and
mobile telephones within the signal coverage area.
If weak signal transmissions occur within the coverage area because of indoor applications,
topological conditions or distance from the transmitter, a Repeater is used to extend
transmission range. In the downlink path the Repeater picks up the signal from a donor
antenna of an existing cell, amplifies and re-transmits it into the desired dark spot. In the
uplink direction the Repeater receives signals from mobile stations present in its coverage
area and re-transmits them to the corresponding base station.
1.2
About the MRx01B Power
This repeater bi-directionally amplifies signals between multiple mobiles and a single base
station in the frequency band. It is employed where poor topological conditions cause weak
field strengths. It can provide highly selective amplification of band segments or channels in
the frequency band.
MRx01B Power modules can be combined with other repeater modules in order to create a
multi-band repeater system. Modules operating in PCS1900, GSM1800, GSM900, or
AMPS800 bands are available. When different modules are combined a common antenna and
control interface are available.
The MRx01B Power can be set-up locally or remotely. A PCMCIA slot for modem operation
is an available option. The repeater has a large number of functions that can be monitored and
changed by the operators via a terminal emulation program or the MIKOM OMC software
platform. An easy to understand and simple to learn communication language is available to
help the operator query status reports from the repeater or to change settings.
1.3
Modular design
The MRx01B repeater’s modular design provides the flexibility in addressing present and
future system needs. Each repeater is custom configured. The main unit includes equipment
common to all systems ( cabinet, control module, power supply, mother board ). To this main
unit hardware modules are added as needed. In addition to different duplexers, a wide range
of conversion modules can be selected depending on the used network system.
M0079A1A.doc
Id.-No. 151775
Page 11
10-March-00
User’s manual for Repeater MRx01B Power
1.4
Applications
The ability to customise the equipment in this way makes it possible to target the MRx01B to
specific needs. For example, the following are some of the application options available with
the MRx01B.
•
Channel selective or band selective
•
CDMA or TDMA
•
iDEN and analog networks
•
GSM900 or GSM1800
•
PCS1900
M0079A1A.doc
Id.-No. 151775
Page 12
10-March-00
User’s manual for Repeater MRx01B Power
2 Functional description
The Repeater MRx01B Power can be equipped from one to four bands or channels depending
on the used technology.
The following block diagram shall illustrate the configuration of the system.
*: one physical module contains UL and DL
**: with more than two modules, the amplifiers are included; both are in one housing
figure 2-1 Block diagram of MRx01B Power
2.1
General
The Repeater consists of two amplifier chains, which are connected antiparallel. The
receive path of one direction is connected to the transmit path of the other direction by a
frequency separation unit, in the following denominated as a duplexer, which combines
both signals to an antenna (see chapter 2.5).
After the duplexer the signals get to a pre-amplifier and afterwards to a conversion
module (see chapter 2.2). Then the signals are combined by the active combiner (see
chapter 2.6) and afterwards amplified by the feedforward amplifier (see chapter 2.8),
which provides the required output power.
M0079A1A.doc
Id.-No. 151775
Page 13
10-March-00
User’s manual for Repeater MRx01B Power
In the feedforward amplifier a power detection measures the output power and controls
the gain. This is called Automatic Level Control (ALC) and keeps intermodulations
below an adjustable value. Finally, the signals are fed to the antenna.
2.2
Conversion modules
The task of the conversion modules is to amplify the
receive signals and to convert them into an intermediate
frequency. The signals, then, proceed a filter stage
comprising of highly selective filters, and run through a
digital controllable attenuator. The attenuation can be
set in steps of 2 dB, locally or remotely. By using the
same synthesizer frequency, that was used to convert the
signals down to intermediate frequency, the
intermediate frequency is mixed up to the original
frequency.
The synthesizer is controlled via an I²C-Bus. In case of a
breakdown in mains, gain or frequency data are nonvolatile stored in an EEPROM on board.
The yellow label on the top shows the current ALC and
CFO values related to the module.
See figure 2-2 Top view of a conversion module for an
exemplary channel or band module.
figure 2-2 Top view of a conversion module
2.3
Mother board
The function of the mother board is the communication between the conversion modules and
the control module via the I²C-Bus.
In the three and four channel configuration there is a mother board implemented on the lefthand side and on the right-hand side of the Repeater.
In the one and two channel configuration of the Repeater there is only one mother board
mounted on the right-hand side (see figure 9-2 and figure 9-3).
Mother boards are located underneath the conversion modules.
M0079A1A.doc
Id.-No. 151775
Page 14
10-March-00
User’s manual for Repeater MRx01B Power
figure 2-3 Top view of a mother board
M0079A1A.doc
Id.-No. 151775
Page 15
10-March-00
User’s manual for Repeater MRx01B Power
2.4
Control module SM 2009 ( Rev. 07 and higher )
The control module SM 2009 is a DOS compatible micro computer. The whole
communication between the operator and the Repeater can be done via the control module. By
using either the RS232 interface in connection with a modem card and a mobile the Repeater
can be controlled remotely or locally by using a VT100 terminal, i.e. a PC emulating the
VT100 terminal.
Frequency and gain, power down of RF stages and ALC can be controlled and status
messages can be received remotely. In case a modem or a mobile is connected, automatic
alarm messages can be received by the operator.
The data transfer between the control module SM 2009 and the mother board is realized by
the I²C-Bus system.
The I²C-Bus concept was developed by Philips for the serial connection of integrated circuits
within one device. Two wires, SDA - serial data and SCL - serial clock, carry information
between the devices connected to the bus. Each device is recognized by a unique address and
can operate either as transmitter or receiver. The MRx01B Power I²C-Bus concept is working
with a bit rate of 1.5 kbit/s.
All MRx01B Power configuration parameters are stored in an EEPROM on the control
module if a power supply failure occurs.
M0079A1A.doc
Id.-No. 151775
Page 16
10-March-00
User’s manual for Repeater MRx01B Power
Functional description:
•
Second RS-232 port ( Not working yet, do not use it ) ( 01)
•
Configurable for MR or MOR (Master Unit) by DIP-Switches (02 )
•
External alarms or PSTN modem selection by DIP-Switches
( = replacement of the external alarm cable) ( 03 )
•
8 additional TTL inputs ( opto-coupled ) ) ( 04 ) ( Not supported by software )
•
8 additional TTL outputs (O.C. or VCC by 1K-pull-up resistor) ( 05 ) ( Not supported by
software )
•
Connector for external temperature sensor ( 06 ) ( Not supported by software )
•
Integrated Battery Backup Dummy Board incl. M1 Reset ( Id.-No. 143750 ).
The switch is required to activate the battery backup. If a battery backup module is used,
the switch must be set to ‘BBU’ position, otherwise there is no backup possible ( 07 ).
•
Soldering point for the PC/MODEM-switch in a Master Unit ( 08 )
•
Reset jumper ( 09 )
•
Fixed location for labels for control module ID (Mikom), repeater software (Mikom),
board serial number, modem-driver licence ( 10 )
•
RS232 interface for the connection of a PC or terminal ( local mode ) ( 11 ).
M0079A1A.doc
Id.-No. 151775
Page 17
10-March-00
User’s manual for Repeater MRx01B Power
09
06
LED L3
LEDs
L1, L2
10
03
07
ON = No BBU
OFF = BBU in
use
01
11
02
05
05
Mode
switch
08
+12 Vdc
for the
modem
04
I2Cbus
Debug
interf.
figure 2-4 Configuration of the control module ( Rev.07 and higher )
M0079A1A.doc
Id.-No. 151775
Page 18
10-March-00
User’s manual for Repeater MRx01B Power
SW802
ON
Ext. Alarm 1
Ext. Alarm 2
Ext. Alarm 3
Ext. Alarm 4
SW503
ON
8 MOR
7 MOR
6 MOR
5 MOR
4 MR
3 MR
2 MR
1 MR
SW501
ON
SW Download
--Modem mode
Manual mode
OFF
----Local mode
SW mode
OFF
PSTN (a)
PSTN (b)
PSTN (c)
PSTN (d)
OFF
MR
MR
MR
MR
MOR
MOR
MOR
MOR
SW504
ON
8 VCC
7 VCC
6 VCC
5 VCC
4 VCC
3 VCC
2 VCC
1 VCC
OFF
O.C.
O.C.
O.C.
O.C.
O.C.
O.C.
O.C.
O.C.
DIP-Switches are at position OFF
figure 2-5 Configuration of the DIP-Switches
M0079A1A.doc
Id.-No. 151775
Page 19
10-March-00
User’s manual for Repeater MRx01B Power
2.5
Duplexer
The task of the duplexer is to isolate uplink from downlink, i.e. isolate transmit path from
receive path. The pass bandwidth of the duplexer is the entire width of the uplink band and
the downlink band.
Duplexer with connector to mobile side
30 dB
coupler
20 dB
coupler
30 dB
coupler
Duplexer with connector to BTS side
figure 2-6 Top view of the duplexers
M0079A1A.doc
Id.-No. 151775
Page 20
10-March-00
User’s manual for Repeater MRx01B Power
2.6
Active combiner
After passing through the conversion modules, the signals will be combined by the active
combiner module in the UL and in the DL path. The active combiner will be followed by the
feedforward amplifier.
figure 2-7 Top view of the active combiner module
2.7
Measuring aids
With built-in RF probes test signals can be applied or detected. The probes provide a coupling
factor of 30 dB respectivly 20 dB. Each duplexer (uplink and downlink) is equipped with one
30 dB coupler, the UL Input duplexer additionally with a 20 dB coupler for a modem or
mobile (see chapter 4 Optional equipment). This facilitates measurements under all
operational conditions, while an antenna or a dummy load may be connected.
The position of the couplers on the duplexers is shown in figure 2-6 Top view of the
duplexers.
M0079A1A.doc
Id.-No. 151775
Page 21
10-March-00
User’s manual for Repeater MRx01B Power
2.8
Feedforward amplifier
The feedforward amplifier is the final stage which enables high output power as well as a high
ICP3. One amplifier has to be installed for the uplink and one for the downlink.
figure 2-8 Top view of the feedforward amplifier
2.9
Power supply
For the MRx01B Power power four power supplies are necessary.
Power supplies are available with different mains power. See list below for available power
supplies.
•
115 VAC ± 15% / 40 - 65 Hz
•
230 VAC ± 15% / 40 - 65 Hz
•
185 - 320 VAC / 40 - 65 Hz
•
24 VDC
•
42 to 60 VDC
•
80 to 130 VDC
M0079A1A.doc
Id.-No. 151775
Page 22
10-March-00
User’s manual for Repeater MRx01B Power
The following figure shows the mounting position of the power supplies in the
MRx01B Power cabinet.
figure 2-9 Mounting position of power supplies
Power supplies can be equipped with a power socket, protected with two fuses. Each power
supply can be switched on or off by means of an external switch. The modules of the Repeater
are voltage free if all power supplies are switched off. The power socket, however, is still
provided with mains power.
F Note:
The service connecter must not be used for anything else but
service devices with low power consumption, e.g. a Laptop.
See figure 2-10 ON / OFF position of external switch.
figure 2-10 ON / OFF position of external switch
F Note:
To switch the whole Repeater voltage free, you have to remove the
fuses F1 and F2 on the screw terminal.
The power supply is factory-set and should not be changed.
M0079A1A.doc
Id.-No. 151775
Page 23
10-March-00
User’s manual for Repeater MRx01B Power
STYLEREFSEQARABICFunctions and features
3.1
Band and channel selectivity
The selectivity is achieved by highly selective filters in the IF part of the band / channel
modules.
3.2
Gain setting
The gain can be changed by introducing attenuation into the amplifier chain. By using a rotary
switch the attenuation can be adjusted locally in the range from 0 dB to 30 dB maximum in
steps of 2 dB. The attenuation can be set for the UL and DL path separately.
The rotary switches are mounted on the mother board. These switches are accessible through
the long hole between the two conversion modules (see figure 3-1 Position of rotary
switches). They can be adjusted easily by means of a small screwdriver.
long hole
figure 3-1 Position of rotary switches
For remote control an RS232 interface can be used to set the gain.
The functions of the control module may be used locally by means of a VT100 terminal or a
personal computer emulating the VT100 terminal. See also chapter 6.2, which deals with
settings of operational parameters.
M0079A1A.doc
Id.-No. 151775
Page 24
10-March-00
User’s manual for Repeater MRx01B Power
3.3
ALC
In order to protect the amplifiers from overload and to prevent the system to generate spurious
emission, the amplifiers have an Automatic Level Control, designed to limit the output power
to a defined level. A part of the output power is rectified, amplified and used to control an
attenuator network.
FNote:
3.4
The ALC protects the feedforward amplifier. To keep spurious emissions
below certain limits, the input power into the Repeater and the attenuation
settings of the repeater have to be considered properly.
CFO
Each conversion module has got a different offset of the set center frequency. This offset is
compensated by software settings (see software manuals).These settings are already factory
set and should only be changed when neccessary. The CFO (center frequency offset) is noted
on the label on top of the conversion module.
3.5
BITE and alarms
The Built-In TEst concept comprises the monitoring of the power supplies, the operational
currents in the conversion modules, the mother board and the remote control interface.
Furthermore, the synthesizer lock and the temperature of the Repeater are monitored.
There are three multicoloured LEDs mounted on the control module. The LED L3 indicates
the presence of electrical power of +12VDC in the Repeater. Every alarm is indicated by the
failure LEDs, L1 and L2.
For the position of the LEDs on the control module see figure 2-4 Configuration of the control
module ( Rev.07 and higher ).
All alarms can be checked by typing the ‘STATUS HIST’ command. Minor alarms with no
influence on the system can be cancelled by typing the ‘ALARMACKN’ command, e.g. ALC
active, VSWR or door open. The following print screen illustrates a possible ‘STATUS
HIST’ report
In case a hardware failure is detected the concerning hardware module has to be replaced. An
alarm can be acknowledged manually by software command. If all alarms have been
acknowledged the summary error LEDs are set back to green indication.
In case of mains power failure all data of the STATUS HIST list are lost.
The alarm can also be sent to the OMC.
M0079A1A.doc
Id.-No. 151775
Page 25
10-March-00
User’s manual for Repeater MRx01B Power
If monitored via a modem automatic dialling will generate a summary alarm message. The
operator can acknowledge the alarm message by a simple ring back and after that he is able to
request a detailed status report.
The following list comprises all available alarms in the Repeater. These alarms may occur in
the STATUS HIST list.
NO.
(7)
10
11
12
(13*)
(14*)
(15*)
(16*)
(17**)
**
(...)
ALARM NAME
AMPLIFIER BIAS
POWER SUPPLY 8 V
POWER SUPPLY 12 V
MAINS
SYNTH
DOOR
VSWR
ALC
LITHIUM BATTERY VOLTAGE
OVERTEMP
INVALID LOGIN ATTEMPT
I2C BUS
EXT. ALARM 1
EXT. ALARM 2
EXT. ALARM 3
EXT. ALARM 4
EXT. BATTERY
ALARM ACTIVE STATUS
FAILURE
FAILURE
FAILURE
FAILURE
FAILURE
OPEN
ALARM
FAILURE
LOW
FAILURE
FAILURE
FAILURE
FAILURE
FAILURE
OVERTEMP.
Alarm default settings changeable by software instruction SET ALIAS.
This alarm may be activated together with the external alarms, for instance UPS or temperature
Optional alarms
table 3-2 List of all available alarms
M0079A1A.doc
Id.-No. 151775
Page 26
10-March-00
User’s manual for Repeater MRx01B Power
3.5.1
Handling of alarms
As soon as the software recognises a valid alarm, a message is transmitted to the OMC.
If the repeater is operating in modem mode the alarm message ‘MIKOM> REPEATER
REQUIRES OPERATOR ATTENTION’ will be sent via modem to the terminal or the OMC.
The first of two stored telephone numbers will be dialled. In case a connection cannot be
established the second telephone number will be dialled. If this should be unsuccessful as
well, the call will be repeated after a pre-set delay. Default setting is 10 minutes. The
repetition cycle can be set by software.
The alarm check routine is searching every 10 seconds for alarms ( polling principal ). To
decide whether an alarm is a valid alarm it must remain for 5 polling cycles, only then it will
be recognized and entered in the alarm history. As soon as the alarm is valid the contacts of
the alarm relay at the mother board are set. Additionally two summary error LEDs are set to
red light to indicate an alarm. These LEDs are mounted on the control module (see figure2-4).
The entry in the alarm history describes the alarm type, the time and the date when it
occurred. It is not possible to locate the defect module, only the reason.
Entered alarms in the alarm list can be acknowledged by simply ringing back and typing a
software command. It is also possible to acknowledge alarms in local mode. Acknowledged
alarms will be indicated with ‘-ACK’. As soon as the alarms have been acknowledged the
alarm relay will be reset and the summary LEDs switch back to green light again. To switch
off external alarm indication devices can only be done by acknowledging the alarms.
If the same alarm cause occurs again, it will be entered in the alarm list ( not acknowledged )
after 5 polling cycles. An already acknowledged alarm must have an interruption of at least 5
polling cycles to be detected by the software as a new alarm. Only then the alarm will be
entered again in the alarm history ( not acknowledged ).
All data of the alarm history are lost, if the repeater will be booted by software or if the
repeater was disconnected from mains. There exists no command to delete the alarm history,
to boot the repeater is the only way to clear the alarm history.
The alarm list has a capacity of about 50 alarm entries. If more alarms occur the oldest
message will be deleted first ( FIFO principal ).
In the software exists no alarm clear message, i.e., the repeater sends no message to the
terminal or the OMC if an alarm has disappeared by itself.
M0079A1A.doc
Id.-No. 151775
Page 27
10-March-00
User’s manual for Repeater MRx01B Power
3.5.2
Status report
Two instructions enable the operator to gain knowledge of the system status. Typing the GET
command will be responded by a listing of all settings of the Repeater. STATUS will be
responded by a listing of all individual status information.
The complete listing of the dialogue language with the processor of the control module
including the instructions to and the messages from the system is available as a separate
manual.
3.5.3
Severity levels
This parameter defines five severity levels for an alarm and can be set in the alarm mask
(detailed description in the software manual). The severity levels indicate how the capability
of the managed object has been affected.
The levels are described below and are ordered from most severe to least severe:
- Critical:
The critical severity level indicates that a service affecting condition has
occurred and an immediate corrective action is required to restore the
capability of the managed object.
- Major:
The major severity level indicates that a service affecting condition has
developed and an urgent corrective action is required. Such a severity can be
reported, for example, when there is a severe degradation in the capability of
the managed object and its full capability must be restored.
- Minor:
The minor severity level indicates the existence of a non-service affecting fault
condition and that corrective actions should be taken in order to prevent a more
serious failure. Such a severity can be reported, for example, when the detected
alarm condition is not currently degrading the capability of the managed object.
- Warning:
The warning severity level indicates the detection of a potential or impending
service affecting failure before any significant effect has been caused. Action
should be taken to further diagnose and correction of the problem shall prevent
a more serious service affecting failure.
- Disable:
The disable severity level indicates that the detected failure has no influence on
the system and shall not be sent to the terminal.
M0079A1A.doc
Id.-No. 151775
Page 28
10-March-00
User’s manual for Repeater MRx01B Power
4 Optional equipment
The following modules can be integrated as an option.
4.1
VSWR module
VSWR signal is continually measured by a special VSWR module. An alarm can be given for
VSWR < 10 dB.
4.2
External alarms
With the following option it is possible to monitor 4 external alarms via the Repeater
software. Hence the status of the connected device, e.g. UPS, can be monitored.
The contacts of the alarms can be accessed at clamps on the main board (right-hand side of
the Repeater).
The electrical connection has to be
as follows:
External alarm 4 (high active)
External alarm 3 (high active)
External alarm 2 (low acitve)
External alarm 1 (low acitve)
Ground
figure 4-1 Clamps for external alarms
Configuration: 5 V / 0.5 mA max. for open collector applications.
All external alarms are normally high without connection. Due to the fact that the external
alarms 3 and 4 are high active, they have to be connected to ground to prevent an alarm
message.
M0079A1A.doc
Id.-No. 151775
Page 29
10-March-00
User’s manual for Repeater MRx01B Power
The factory-set response after typing the software command STATUS EXTALARM is for
instance „EXT. ALARM 1 OK“, if the alarm is not active and „EXT. ALARM 1 FAILURE“,
if the alarm is active.
The name for each external alarm and the name for the alarm message can be defined by the
customer with the corresponding software command.
The following example describes the response for the external alarms to control an UPS.
Example:
External alarms if the UPS is active
EXTERNAL ALARM STATUS
UPS alarm active
Battery low !
UPS door open
Battery door open
or
External alarms if the UPS is not active
EXTERNAL ALARM STATUS
UPS not active
Battery OK
UPS door closed
Battery door closed
If the optional external alarms are part of the delivery, they will be switched on by a software
release, i.e. they are distributed via the software.
4.3
Modem
The Repeater can be equipped with a modem for the remote control of the repeater. This
allows the operator to change settings and querry information of the Repeater remotely.
See figure 4-2 for the optional modem kit. This kit is available with and without modem.
For information referring to the optional modem see chapter 4.4 and chapter 6.2.4.
M0079A1A.doc
Id.-No. 151775
Page 30
10-March-00
User’s manual for Repeater MRx01B Power
PCMCIA card
Modem
figure 4-2 Modem kit
4.4
External RF output
An external output is available at the
outside of the housing as an option. This
enables e.g. the connection of an
integrated modem or mobile to an
additional external antenna or it might be
used for UL diversity. The connector type
is N female.
External RF
figure 4-3 Position of external RF output
M0079A1A.doc
Id.-No. 151775
Page 31
10-March-00
User’s manual for Repeater MRx01B Power
4.5
Battery backup module
If backup is required only for the control module and the modem, low capacity batteries are
available to operate controller and modem for at least ten minutes under normal
environmental conditions.
Battery backup is provided for the control module to transmit alarm information in case of
power failure. The battery type is a NiCd 8.4V/300 mAh. The battery backup is sufficient
enough to support multiple dial out attempts via modem in case of ‘system engaged’ or other
communication problems for at least ten minutes under normal environmental conditions.
F Note:
This battery backup module is provided for the control module only.
The batteries are protected from deep discharge by use of a low voltage disconnect circuit. A
local switch is provided to disconnect the battery backup system during maintenance to ensure
that all circuits are voltage-free.
The switch is located on the battery backup module.
Switch
ON (default)
OFF
Battery backup active Battery backup not active
The module is directly plugged into the control module. During the charging process a green
LED V7 on the module indicates, that the battery is charged at the moment. After finishing
the process the LED V7 will be switched off.
The batteries are mounted underneath the modem mounting plate (see following figure).
Batteries
figure 4-4 Mounting position of batteries
M0079A1A.doc
Id.-No. 151775
Page 32
10-March-00
User’s manual for Repeater MRx01B Power
Installation
TX Downlink
RX Uplink
TX Uplink
RX Downlink
to/from
Mobile Stations
to/from
BTS
Repeater System
TX Downlink
RX Uplink
TX Uplink
RX Downlink
Mobile
BTS
figure 5-1 System description
M0079A1A.doc
Id.-No. 151775
Page 33
10-March-00
User’s manual for Repeater MRx01B Power
5.1
Mechanical installation
Note:
Due to power dissipation the Repeater may heat up the air volume inside
the cabinet and reach a very high temperature. Therefore it is necessary to mount the
Repeater in the vertical plane to a wall or a mast without additional enclosure to provide
sufficient ventilation. Between the housing and the wall a minimum distance must be
kept in order to provide air circulation.
The Repeater must be mounted in the
vertical plane to a wall or a mast, which
means the connectors have to be located at
the bottom.
Use the mounting brackets, which are part
of the delivery. This will guarantee a
minimum distance between the wall and the
Repeater housing. The cabinet must be
fixed to the wall (brackets) with four
screws.
Check the correspondence of the wall
mounting kit and the wall.
figure 5-2 Top view and clearance distance
F Note:
M0079A1A.doc
The weight of the MRx01B Power is approximately 47 kg in standard
configuration.
Id.-No. 151775
Page 34
10-March-00
User’s manual for Repeater MRx01B Power
Mounting procedure:
Dismount the mounting brackets first. They are screwed tight to the housing with four socket
head cap screws M8.0x16 (see figure below) and two tire bolts.
mounting brackets
figure 5-3 Wall mounting brackets
Use the wall mounting sheet to mark the position of the drilling holes. Drill 4 holes and screw
the mounting brackets to the wall. Attach the upper two socket head cap screws M8.0x16 to
the Repeater housing. Now it is possible to hang the Repeater into the mounting brackets. Fix
then the lower two socket head cap screws M8.0x16 and the 2 tire bolts.
F Note:
The unit is heavy-weight. Make sure that a suitable mounting surface is
used. Only adequate manpower is allowed to handle the system.
The installation position of the Repeater follows from the installation drawing (see figure 9-1
Installation drawing of the Repeater). Make sure that there is free access to the electrical
connections. The allowed bending radius of the connected cables must not be exceeded.
Furthermore the Repeater shall be mounted in a way that there is free access to the individual
units inside the cabinet, while the door of the Repeater is open.
Therefore keep a clearance distance of 1 m on each side, on top and below the unit.
See figure 5-2 Top view and clearance distance.
M0079A1A.doc
Id.-No. 151775
Page 35
10-March-00
User’s manual for Repeater MRx01B Power
5.2
Electrical installation
FNote:
5.2.1
ESD precautions have to be observed! Before working inside the cabinet
use the available grounding system to connect ESD protection measures.
The electrical installation has to be performed in accordance with the
safety regulations of the local authorities. Due to safety reasons the
electrical installation must be performed by qualified personnel. The
cover of this unit should not be opened while power is applied.
Subsequent installation, commissioning and maintenance activities that
require the unit to be powered with the cover open shall only be carried
out by suitably qualified personnel
Grounding
Grounding has to be performed by all means. Therefore a grounding bolt is provided at the
cabinet. An earth bonding cable will be mounted in the factory and will be delivered with the
unit. Don’t use the grounding screw for connecting external devices.
The complete grounding kit is part of the delivery schedule, see figure 5-4 Grounding kit.
figure 5-4 Grounding kit
M0079A1A.doc
Id.-No. 151775
Page 36
10-March-00
User’s manual for Repeater MRx01B Power
5.2.2
Power connection
A firmly installed mains cable 3 x 1.5 mm² is used, which is fed into the housing through a
watertight cable gland. Due to safety reasons the power supply lead has to be protected by two
8 A fuses. Inside the Repeater, mains are connected to a screw terminal.
See figure 5-5 Screw terminal for the position of the two 8 A fuses.
Before connecting electrical power to the Repeater grounding has to be performed. The
Repeater is equipped with a firmly connected power cord 3 x 1.5 mm². Due to safety reasons
the power supply lead of the Repeater has to be protected with two 8 A fuses, type MT. In the
event the length of the power cord should not be sufficient it can be replaced by a longer
cable.
Fuses F1 and F2
figure 5-5 Screw terminal
F Note:
5.2.3
If the power supply lead has to be replaced use a cable of the same quality.
Connection of the antenna cables
The Repeater has two female antenna connectors 7/16 (optionally N). For mounting the
corresponding cable connectors we recommend to refer to the applicable documentation of
the respective connector manufacturer. The bending radius of the antenna cables must remain
within its specification. This will warrant proper operation of the system; otherwise changes
in the electrical behaviour of the cable might occur which could cause malfunction of the
Repeater system.
M0079A1A.doc
Id.-No. 151775
Page 37
10-March-00
User’s manual for Repeater MRx01B Power
F Note:
It is sufficient to fix the 7/16 antenna connectors hand-screwed.
Any use of a tool (like tongs) might cause damage to the connectors and
thus lead to malfunctioning of the Repeater.
There are two 7/16 female antenna connectors at the outside of the housing accessible on the
connector panel (see following figure).
figure 5-6 Connector panel layout
The 7/16 TX-downlink connector should be connected to the antenna system for the
communication with the mobile units.
Mobile
The 7/16 TX-uplink connector should be connected to the antenna system for the
communication with the Base Transceiver Station.
BTS
As an option a 7/16 - N adapter is available.
M0079A1A.doc
Id.-No. 151775
Page 38
10-March-00
User’s manual for Repeater MRx01B Power
6 Setting to work
6.1
Preparation
F Note:
It is not allowed to operate the Repeater without termination of the
antenna connections! The termination can be performed by the antenna
connection as well as a dummy load or the 50-Ohm-terminated connection
of a measuring instrument.
Before bringing the Repeater system into service it is necessary to measure the antenna
isolation. The Repeater system has its maximum available gain when the attenuation is set to
zero. On site the maximum allowed gain is 15 dB less than the value of the antenna isolation.
In order to check the function of the Repeater system on site it is advisable to operate the
Repeater system with 50 Ohm termination. This makes it possible to set the necessary gain
and to test the set value without the necessity of transmitting on air.
In order to perform settings the Repeater has to be opened. Please, ensure not to damage the
seals, which are on the modules situated on the conversion modules inside of the Repeater,
because this would lead to risk the success of warranty claims.
After taking the Repeater into service following signals occur during the boot process.
Internal
LED L1
green
red
Flashes
red short
time
Internal
LED L2
green
red
Internal
LED L3
green
Flashes red
short time
Cause
Power on state,
Software boot starts
Software boot starts
Software is running
table 6-1 LED indication
6.2
Setting of operational parameters
Attenuation of the Repeater can be set manually by means of rotary switches, frequency can
be set locally or remotely.
There are three different possibilities to set the operational parameters:
-manual settings by means of rotary switches
-local control via RS232 interface and PC
-remote control via modem
M0079A1A.doc
Id.-No. 151775
Page 39
10-March-00
User’s manual for Repeater MRx01B Power
6.2.1
Manual settings by means of rotary switches
The manual mode allows the user to set the required channels and attenuation by means of
rotary switches. With a small screwdriver, which fits through the long holes of the conversion
modules, the values can be adjusted by turning the switch carefully to the desired position.
F Note:
To enable manual settings of parameters
the mode switch (DIP-Switch 1) has to be
changed from OFF to ON.
The DIP-Switch is mounted on the control module, located on the left side of the Repeater.
RAM/RTC Battery
DIP-Switch 1
and 2
RS 232 port
connector
figure 6-2 Position of the DIP-Switch 1 and 2 and RAM/RTC battery
6.2.2
Setting of the attenuation
The gain can be set by introducing attenuation into the amplifier chain. By using a rotary
switch the attenuation can be adjusted locally in the range from 0 dB to 30 dB maximum in
steps of 2 dB. The attenuation can be set for the UL and DL path separately.
The rotary switches are mounted on the mother board. These switches are accessible through
the long hole between the two conversion modules (see figure 6-3 Position of the rotary
switches). They can be adjusted easily by means of a small screwdriver.
M0079A1A.doc
Id.-No. 151775
Page 40
10-March-00
User’s manual for Repeater MRx01B Power
long hole
figure 6-3 Position of the rotary switches
A label on the conversion module, located next to the rotary switch, illustrates the usage of
the rotary switch.
figure 6-4 Rotary switches and label
F Note:
M0079A1A.doc
Gain can be changed independently for the uplink and downlink path.
Id.-No. 151775
Page 41
10-March-00
User’s manual for Repeater MRx01B Power
DIP-Switch configuration:
DIP-Switch
ON
manual
remote mode
n.c.
software download
manually controlled
OFF (default values)
auto
local mode
n.c.
software download
controlled by software
table 6-5 DIP-switch configuration
6.2.3
Settings via personal computer as terminal
Instead of manually setting operational parameters via rotary switches it is also possible to use
the functions of the control module. The local mode for settings via PC has to be set.
Therefore the DIP-Switch 2 has to be at position OFF.
DIP-Switch 2
See figure 6-2 for
postition of DIP switch 2
A VT100 terminal or a PC with VT100 emulation can be connected to the control module
SM2009 by a standard RS232 cable, if necessary in connection with an adapter 9 to 25.
See figure 6-2 for position of the RS 232 connector.
Cable Connections PC
9 contact SUB - D- Connector
male
PC
PIN
M0079A1A.doc
Control Module SM2009
9 contact SUB - D- Connector
male
RS 232
MRx01B Power
PIN
Id.-No. 151775
Page 42
10-March-00
User’s manual for Repeater MRx01B Power
The following communication mode between control module and VT100 is set initially.
9600 baud - 8 bit - no parity -1 stopbit
These settings can only be changed after connection of the terminal. If all wanted settings
have been initialized and a modem has to be used it will be recommended to check whether
the settings comply with the capabilities of the modem and the line. Modifications are
possible by software commands.
F Note:
Settings on the Repeater can be performed after the following procedure
only.
After connecting the PC to the Repeater, following procedure is necessary to get access to the
program.
MIKOM REPEATER MRx01B Power - SM2009 - SW: REP1007V1.11
ENTER <.>  TO LOGIN
1. Step:
Type the two keys ( . ) FULLSTOP and (↵) ENTER
You have to type the keys:
2. Step:
ENTER PASSWORD
You have to enter:
M0079A1A.doc
UserID1 ↵
The input is case sensitive, no blanks. After three mistrial follows
disconnection.
3. Step:
F Note:
↵
ENTER USER ID
You have to enter:
F Note:
P-word1 ↵
The input is case sensitive, no blanks. After three mistrials follows
disconnection.
Id.-No. 151775
Page 43
10-March-00
User’s manual for Repeater MRx01B Power
6.2.4
Settings via modem
The Repeater can be equipped with a modem. If so, the repeater will be delivered with a
preset init string. This init string was used for internal tests. In case no connection can be
established check the local conditions and change the init string if necessary.
The following list contains the description of the AT commands:
&F
Sets modem to factory configuration
E0
Echo OFF
S0=1
Auto answer ON; the GSM module / M1 modem goes offhook after the first ringing signal.
S7=60
Waiting time for connection after dialing; permissible values
are from 0 ... 60.
B13
Setting to 9600 bps asynchronous mode
\ N6
Auto reliable operation
\ N0
Standard operation, no error correction
+CBST=7,0,1
Set bearer service type to 9600 bps. Non-transparent
connection (uses RLP)
X3
Not waiting for dial tone; usually used at PABX.
*P1
Switch ON phone
&K4
Enables XON / XOFF flow control
table 6-6 List of AT commands
M0079A1A.doc
Id.-No. 151775
Page 44
10-March-00
User’s manual for Repeater MRx01B Power
7 Trouble shooting
All Repeaters are factory-set to „Power down disabled“ status, this means the channel group
is active. To switch off the channel group use the software command „PWRDOWN enabled“.
(You’ll find a detailed description in the software manual.)
7.1
Error indication
l = LED on
- = LED off
Internal
LED L1
green
red
Internal
LED L2
green
red
7.2
Internal
LED L3
green
Cause
No power.
Check presence of power at
the input; replace fuse
according to chapter 8.3,
check battery backup module
Indicates a
summary failure
Alarm monitoring with the STATUS HIST command
Check alarms with ‘status hist‘ command.
1. If a hardware module is damaged, replace corresponding hardware module.
2. Minor alarms with no influence on the system can be cancelled by confirming the alarm
with the ‘alarmackn’ command, e.g., ALC active, VSWR, RSSI or DOOR OPEN.
3. If all alarms have been acknowledged the summary error LEDs will be set back to green
indication.
4. In case of mains power failure the contents of the actual STATUS HIST list is lost.
For a complete list of available alarms, see table 3-2 List of all available alarms
M0079A1A.doc
Id.-No. 151775
Page 45
10-March-00
User’s manual for Repeater MRx01B Power
7.3
Power supply
The output voltage is factory set and should not be changed.
7.4
General remarks
• After a software download previous user settings (data default values) might be
overwritten. Before you start a software download save the set values for:
centre frequency
attenuation
ALC threshold
CFO
• If an ALC or AMPBIAS alarm occurs during installation or commissioning an user error
might be the cause, due to wrong measurements.
M0079A1A.doc
Id.-No. 151775
Page 46
10-March-00
User’s manual for Repeater MRx01B Power
8 Maintenance
8.1
General
F Note:
The Repeater does not require preventative maintenance measures.
It is only recommended to replace the RAM/RTC battery after three years usage as a
prophylactic measure. The nominal lifetime of these batteries is five years under normal
environmental conditions.
In the event of a malfunction it is advantageous to check the status of the antenna systems as
well as the continuity of the entire cabling including connectors, before replacing the
modules.
Maintenance on the Repeater shall be performed only by replacing modules. Soldering on
printed circuit boards shall be avoided. In order to sustain warranty take care not to damage
unintentionally the seals on the modules.
The spare part list, consequently, contains only units, which can be replaced without tuning or
complex soldering work.
F Note:
Defect parts should be replaced by original parts from MIKOM only.
All interventions inside the housing are at one’s own risk.
During maintenance ensure that the Repeater has been disconnected from
mains.
Open the lock at the connector panel and remove the cover plate. To open the housing use a
Torx key and unscrew the four Torx screws.
8.2
Replacement of the fuses (mains)
The mains cable is protected with two fuses F1 and F2 8A type MT. They are accessible
inside of the Repeater at the fuse terminal on the right side. Open the screw plug for the fuse
and take out the fuse.
F Note:
Use only fuses of the same type and the same rating when replacing!
See figure 5-5 Screw terminal for position of the 8A fuses.
M0079A1A.doc
Id.-No. 151775
Page 47
10-March-00
User’s manual for Repeater MRx01B Power
8.3
Replacement of the power supply fuse
Each power supply is protected with a fuse 10 A / 35 V. The fuse is mounted outside of the
power supply housing. (see following figure)
F Note:
Use only fuses of the same type and the same rating when replacing!
figure 8-1 Position of power supply fuse
8.4
Replacement of the mains cable
The Repeater will be delivered with a firmly connected mains cable.
In case the length of the delivered mains cable should not be sufficient or in case of a defect,
the mains cable can be replaced.
F Note:
Disconnect Repeater from mains first.
Remove the clamping profile at the outside of the housing
by pulling at the mains cable. Open the PG9 threaded joint
with a spanner size 17. Inside the housing remove the
plastic cable clip by unscrewing the tallow-drop screw.
Then use a small screwdriver and open the screws of the
fuse terminal.
M0079A1A.doc
Id.-No. 151775
Page 48
10-March-00
User’s manual for Repeater MRx01B Power
Now the mains cable can be removed by pulling at the
cable. For the installation of a new cable strip the
isolation of a new cable to the length of 18 cm. Put the
screw of the cable gland over the cable then use the
joint rubber and pull it over the cable. This will
guarantee a tight connection. Now insert the cable.
Inside the housing pull an insulated tube with the length
of 8 cm over the wires. Now close the PG9 threaded
joint. Screw the wires to the fuse terminal. Fix the cable
with the plastic cable clip.
Put the cable in the guide shaft and close it with the clamping profile.
8.5
Replacement of the RAM / RTC battery
The RAM / RTC battery of the control module has to be replaced in case of memory loss or
as a preventive measure after approximately three years usage. The RAM / RTC battery is
mounted on the left-hand side of the Repeater on the control module.
REFIf the optional battery backup module and the optional mobile kit are installed, the battery
backup board and the modem-reset board, which are plugged into the control module have to
be removed first.
Take off the Lithium battery by means of a small screwdriver, placed between the battery and
the battery socket.
The type of the battery is CR 2450 Lithium 3 V / 500mAh, manufacturer is RENATA.
After replacement of the RAM battery, the control module has its basic settings, date and time
have to be set to the actual value.
For position of the RAM/RTC battery see figure 6-2
EMBED
F Note:
Before replacing the battery, disconnect the Repeater from mains.
Observe the rules for changing Lithium batteries. Wrong connection or
treatment may result in bursting of the battery and dissemination of
hazardous substances.
Don’t try to charge this battery
M0079A1A.doc
Id.-No. 151775
Page 49
10-March-00
User’s manual for Repeater MRx01B Power
8.6
Replacement of the duplexers
This description is valid for the one channel configuration of the Repeater only. For different
configurations refer to the assembly guide for the Repeater.
Remove the semi-rigid cables which connect the UL output and the DL output with the
feedforward amplifier by loosing the SMA connectors. Use a torque wrench. Then remove the
semi-rigid cables from the conversion modules. (BTS side marked with a red spot).
It is recommended not to remove the amplifier which is mounted on the backside of the
duplexer. A new duplexer will be delivered with a premounted amplifier.
Unscrew the four counter sunk screws M3 at the connector panel of the Repeater. See figure
5-6 Connector panel layout.
For mounting the duplexers proceed in reverse order.
The cables have to be connected like shown in figure 9-4 Cabling of one channel Repeater.
8.7
Replacement of conversion modules
To remove the conversion modules, disconnect the SMA connectors by means of a torque
wrench.
If the Repeater is equipped with iDEN channel modules, the external filter on top of the
modules must be dismounted beforehands. The external filter box covers two of the socket
head cap screws the iDEN module is fixed with.
M0079A1A.doc
Id.-No. 151775
Page 50
10-March-00
User’s manual for Repeater MRx01B Power
Unscrew the socket head cap screw on top
of the external filter box, remove the box
carefully and continue the dismounting
procedure like described below.
Socket head
cap screw
figure 8-2 External filter at iDEN module
Unscrew six socket head cap screws by means of a hex socket key.
Pull carefully by means of the mounting strap, fixed on the module and take off the modules.
Socket head cap
screws
Mounting
strap *
Connecting the
conversion modules
depends on the number of
channels your Repeater is
equipped with, i.e. with one up
to four (iDEN: six) channels.
Each configuration has got a
different cabling. See assembly
guide of the channel modification
kits for the cabling and functional
description of the conversion
modules dependent on the
configuration of the Repeater
figure 8-3 Top view of a conversion module
*: iDEN modules are equipped with mounting straps on the left and on the right side.
M0079A1A.doc
Id.-No. 151775
Page 51
10-March-00
User’s manual for Repeater MRx01B Power
For the exchange of a conversion module or the installation
of a new conversion module, the slave address of the synthesizer
has to be set. This can be done by means of hex-coded
rotary switches mounted on the lower side of the modules
Hex-coded rotary switch for UL
Hex-coded rotary switch for DL
The synthesizer address must be set like shown
in the following table:
Address
UL
DL
Conversion module
Channel one
Channel two
Channel three
Channel four
figure 8-4 Position of hex-coded
rotary switches
table 8-5 Address of synthesizer
Conversion modules with variable bandwidth have four rotary switches. The synthesizer
address must be set like shown in the following table:
Filter 1
UL DL
Channl one
Channel two
Channel three
Channel four
Filter 2
UL DL
table 8-6 Adress of synthesizer, conversion modules
with variable bandwidth
figure 8-7 Position of hex-coded rotary switches
at variable bandwidth module
Further instructions for band selective modules with variable bandwith can be found in a
separate document.
M0079A1A.doc
Id.-No. 151775
Page 52
10-March-00
User’s manual for Repeater MRx01B Power
8.8
Replacement of the control module SM 2009
The control module is a Printed Circuit Board situated on the left-hand side of the Repeater.
Disconnect the DC cable from power supply.
Disconnect the flat cable.
Remove the Tyrap which is fixed to the control module.
Disconnect the RS232 cable from the modem if the Repeater is equipped with a modem.
Dismount the battery backup board, if the battery backup module is installed.
Take off the whole control module completely with mounting plate by unscrewing four tallow
drop screws M4.
For mounting proceed in reverse order.
Position of the control module in the Repeater is illustrated in REFthe following figure.
Control module
figure 8-8 Position of control module
M0079A1A.doc
Id.-No. 151775
Page 53
10-March-00
User’s manual for Repeater MRx01B Power
8.9
Replacement of power supplies
FNote:
Ensure that mains are disconnected.
Open the Repeater to get access to the devices.
Remove all connected cables from the clamps of the power supply. Try to loose the plug by
means of a small screwdriver placed between the plug and socket.
ON
Fuse 10A / 35V
figure 8-9 Power supply
The power supply is fixed to the Repeater housing by means of two special nuts M4. After
loosen the screws the power supply can be removed. To open these screws a special key with
a spherical head is required. Place a small screwdriver between the Repeater housing and the
power supply to loose the device.
figure 8-10 Position of special-nut M4
F Note:
M0079A1A.doc
Don’t forget to put heat conducting paste on the mounting side for
installation of a new power supply. Use the conducting paste, which is
included in the spare parts kit.
Id.-No. 151775
Page 54
10-March-00
User’s manual for Repeater MRx01B Power
8.10 Replacement of active combiner modules
The active combiner modules are mounted on both sides of the Repeater.
Disconnect all SMA connectors by means of a torque wrench.
Unscrew two counter sunk screws M3x20mm.
counter
sunk
screws
figure 8-11 Position of counter sunk screws on active combiner
The cabling of the active combiners depends on the configuration of the Repeater. For correct
connections see assembly guide for the channel modification kits.
8.11 Replacement of feedforward amplifier
There is one feedforward amplifier mounted on each side of the Repeater.
A special reset board is connected to the 15 pole SUB-D connector. (See figure 8-12 Position
of feedforward amplifier reset board)
This reset board is part of the feedforward amplifier. A new feedforward amplifier will be
delivered with a premounted reset board.
M0079A1A.doc
Id.-No. 151775
Page 55
10-March-00
User’s manual for Repeater MRx01B Power
Reset board
figure 8-12 Position of feedforward amplifier reset board
Remove the ready made cable which is plugged to the 15 pole SUB-D connector of the reset
board. Unscrew the screw clip first.
Unscrew the 6 socket head cap screws.
The SMA connectors can be removed only after dismounting the amplifier.
The position of the feedforward amplifiers is illustrated in figure 8-13 Position of feedforward
amplifiers.
M0079A1A.doc
Id.-No. 151775
Page 56
10-March-00
User’s manual for Repeater MRx01B Power
figure 8-13 Position of feedforward amplifiers
M0079A1A.doc
Id.-No. 151775
Page 57
10-March-00
User’s manual for Repeater MRx01B Power
9 Appendices
9.1
Repeater specifications
ELECTRICAL SPECIFICATIONS
Id-No:
Frequency range & bandwidth
Frequency selectivity;
Gain outside operating band
Gain (nominal)
Gain adjust
Gain variation over frequ. and temp.
Tolerance per step
Delay
Delayripple
Output power ALC limit (test case)
at 2 equal carriers
ICP3
ALC limit tolerance of frequency
and temperature
ALC overload reaction time delay
Noise figure
Test coupler
Return loss (@ 25° C amb. temp.)
Power Supply
Power consumption (1 module)
Remote control interface
Connectors
Environmental and Safety
Built in test equipment
Alarm forwarding
Control functions
MR301B Power
150047
Up to 25 MHz in GSM900
± 400 kHz: 50 dB max.; ± 600 kHz: 40 dB max.
± 1000 kHz: 35 dB max.; ± 5000 kHz: 25 dB max.
85 dB
0 to 30 dB in steps of 2 dB
± 2.5 dB (± 3.5 dB at extreme temperature range)*
± 0.5 dB from 0 to 6 dB attenuation
± 2.0 dB from 8 to 30 dB attenuation
6 µsec.max.
150 ns
30 dBm (@ 25° C)
+27 dBm / +27 dBm*
58 dBm @ max. gain
±3 dB
3 msec. (others available on request)
6 dB @ max. gain;
8 dB @ 75 dB gain;
30 dB
15 dB
230 Vac ± 15% / 40.-.65 Hz;
Option:24 Vdc or 42 - 60 Vdc or 80 – 130 Vdc,
115 Vac ± 15% / 40.-.65 Hz or 185 – 320 Vac /
40 - 65 Hz
160 Watts
SM 2009
7/16 female; N as an option
see Environmental and Safety leaflet for MIKOM
outdoor cell enhancers
Current monitor • synthesizer lock monitor •
temperature • ALC active
Potential free relay contact and automatic alarm
call via RS232 or PCMCIA interface
Gain • Center frequency • ALC threshold
* Normal temp.range
+ 5° C to + 40°C
Extreme temp.range- 33° C to + 50° C
M0079A1A.doc
Id.-No. 151775
Page 58
10-March-00
User’s manual for Repeater MRx01B Power
ELECTRICAL SPECIFICATIONS
Frequency range Id-No:150043
150044
150045
150046
Bandwith
Frequency selectivity;
Gain outside operating band
Gain (nominal)
Gain adjust
Gain variation over frequ. and temp.
Tolerance per step
Delay
Delayripple
Output power ALC limit (test case)
at 2 equal carriers
ICP3
ALC limit tolerance of frequency
and temperature
ALC overload reaction time delay
Noise figure
Test coupler
Return loss (@ 25° C amb. temp.)
Power Supply
Power consumption (1 module)
Remote control interface
Connectors
Environmental and Safety
Built in test equipment
Alarm forwarding
Control functions
MR401B Power
UL:1710-1740 MHz; DL:1805-1835 MHz
UL:1721,7-1751,7MHz; DL:1816,7-1846,7 MHz
UL:1730-1760 MHz; DL:1825-1855 MHz
UL:1751,5-1784,9 MHz; DL:1846,5-1879,9 MHz
Up to 35 MHz
± 400 kHz: 50 dB max.; ± 600 kHz: 40 dB max.
± 1000 kHz: 35 dB max.; ± 5000 kHz: 25 dB max.
85 dB
0 to 30 dB in steps of 2 dB
± 2.5 dB (± 3.5 dB at extreme temperature range)*
± 0.5 dB from 0 to 6 dB attenuation
± 2.0 dB from 8 to 30 dB attenuation
6 µsec.max.
150 ns
30 dBm (@ 25° C)
+27,5 dBm / +27,5 dBm*
57 dBm @ max. gain
±3 dB
3 msec. (others available on request)
6 dB @ max. gain;
8 dB @ 75 dB gain;
30 dB
15 dB
230 Vac ± 15% / 40.-.65 Hz;
Option:24 Vdc or 42 - 60 Vdc or 80 – 130 Vdc,
115 Vac ± 15% / 40.-.65 Hz or 185 – 320 Vac /
40 - 65 Hz
160 Watts
SM 2009
7/16 female; N as an option
see Environmental and Safety leaflet for MIKOM
outdoor cell enhancers
Current monitor • synthesizer lock monitor •
temperature • ALC active
Potential free relay contact and automatic alarm
call via RS232 or PCMCIA interface
Gain • Center frequency • ALC threshold
* Normal temp.range
+ 5° C to + 40°C
Extreme temp.range- 33° C to + 50° C
M0079A1A.doc
Id.-No. 151775
Page 59
10-March-00
User’s manual for Repeater MRx01B Power
ELECTRICAL SPECIFICATIONS
MR701B Power
Frequency range
Id.No.
UL frequency
[MHz]
1850 – 1885
1865 – 1890
1875 – 1910
148604
151075
148605
DL frequency
[MHz]
1930 – 1965
1945 - 1970
1955 - 1990
Useable bandwidth
35 MHz (25 MHz in 151075) in the upper or
lower PCS band
Gain
90 dB
Gain variation over
frequency and temperature*
±2.5 dB (±3.5 dB at extreme temperatures)
Gain adjust range
30 dB in 2 dB steps
Gain adjust range tolerance
±0.5 dB
Return loss
15 dB @ 25°C ambient temperature
Spurious/intermodulation
-13 dBm max
Spectral re-growth (CDMA only)
-45 dBc (J-STD-008)
Power supply
100-130 VAC / 40-60 Hz
Option: 15-24 VDC or 36-72 VDC
Option: 220-250 VAC / 40-60 Hz
RF connector
7/16 female
Option: N female
Environmental and safety
See separate leaflet
*: Normal temperature range +5° to +40°C; Extreme temperature range -33° to +50°C
M0079A1A.doc
Id.-No. 151775
Page 60
10-March-00
User’s manual for Repeater MRx01B Power
AVAILABLE POWER PER TECHNOLOGY
Pout at 1 channel
Pout/channel at 2 channels
Pout/channel at 4 channels
Pout/channel at 8 channels
ALC threshold
M0079A1A.doc
CDMA
37.0 dBm
31.0 dBm
28.0 dBm
25.0 dBm
Id.-No. 151775
TDMA
40.0 dBm
34.0 dBm
29.0 dBm
26.0 dBm
Adjustable
Page 61
GSM
40.0 dBm
37.0 dBm
33.0 dBm
29.0 dBm
10-March-00
User’s manual for Repeater MRx01B Power
BAND AND CHANNEL SPECIFICATIONS
3 dB bandwidth
Option I
(fixed bw)
5 MHz
Option II
(fixed bw)
15 MHz
Slope 3 dB to 30 dB
1 MHz
2 MHz
30 dB bandwith
50 dB bandwith
Option III
(variable bw)
Channel
CDMA
1.23 MHz
TDMA
30 kHz
2 MHz
fc ± 900kHz
fc ±60 kHz
fc ± 1.5 MHz
fc ± 120 kHz
Delay
6 µs
3 µs
6 µs
< 6 µs
20 µs
Delay variation
(typical)
±150 ns
±150 ns
±150 ns
±500 ns
±500 ns
Far off selectivity
40 dB
40 dB
40 dB
60 dB
55 dB
NF at Gmax
6 dB
6 dB
8 dB
6 dB
6 dB
NF at Gmax-30 dB
12 dB
12 dB
13 dB
12 dB
12 dB
OICP-3 at Gmax
59.0 dBm
59.0d Bm
59.0 dBm
59.0 dBm
59.0 dBm
OICP-3 at Gmax 10 dB
58.6
58.5
58.5
58.5
59.0
dBm
dBm
dBm
dBm
dBm
58.0
58.0
57.5
58.0
58.5
dBm
dBm
dBm
dBm
dBm
56.0
56.0
53.0
55.0
57.0
dBm
dBm
dBm
dBm
dBm
-78 dBm/Hz -78 dBm/Hz -76 dBm/Hz
Output noise out of
-98 dBm/Hz -98 dBm/Hz -96 dBm/Hz
band at Gmax
OICP-3 at Gmax 20 dB
OICP-3 at Gmax 30 dB
0.1 to 15
MHz
Output noise
in band at Gmax
Power consumtion
standby/max power
1 module (typ.cons)
130/220W
130/220W
145/220W
130/210W
130/210W
4 modules (typ.cons)
160/250W
160/250W
180/270W
160/240W
160/240W
M0079A1A.doc
Id.-No. 151775
Page 62
10-March-00
User’s manual for Repeater MRx01B Power
ELECTRICAL SPECIFICATIONS
MR801B Power
Frequency range
Uplink 824-849 MHz; Downlink 869-894 MHz
Useable bandwidth
25 MHz in the upper or lower AMPS 800 band
Gain
90 dB
Gain variation over
frequency and temperature*
±2.5 dB (±3.5 dB at extreme temperatures)
Gain adjust range
30 dB in 2 dB steps
Gain adjust range tolerance
±0.5 dB
Return loss
15 dB @ 25°C ambient temperature
Spurious/intermodulation
-13 dBm max
Spectral re-growth (CDMA only)
-45 dBc (J-STD-008)
Power supply
115 VAC ± 15% / 40 - 65 Hz
Option: 230 VAC ± 15% / 40 - 65 Hz
Option: 185 - 320 VAC / 40 - 65 Hz
Option: 24 VDC
Option: 42 to 60 VDC
RF connector
7/16 female
Option: N female
Environmental and safety
See separate leaflet
*: Normal temperature range +5° to +40°C; Extreme temperature range -33° to +50°C
AVAILABLE POWER PER TECHNOLOGY
Pout at 1 channel
Pout/channel at 2 channels
Pout/channel at 4 channels
Pout/channel at 8 channels
ALC threshold
M0079A1A.doc
CDMA
37.0 dBm
31.0 dBm
28.0 dBm
25.0 dBm
Id.-No. 151775
TDMA
40.0 dBm
34.0 dBm
29.0 dBm
26.0 dBm
Adjustable
Page 63
Analog
40.0 dBm
37.0 dBm
33.0 dBm
29.0 dBm
10-March-00
User’s manual for Repeater MRx01B Power
BAND AND CHANNEL SPECIFICATIONS
Variable Bandwidth
Channel
CDMA
TDMA
3 dB bandwidth
0.1 to 15.0 MHz
1.23 MHz
30 kHz
Slope 3 dB to 30 dB
2 MHz
30 dB bandwith
fc ± 900 kHz
fc ± 60 kHz
50 dB bandwith
fc ± 1.5 MHz
fc ± 120 kHz
Delay
6 µs
< 6 µs
20 µs
Delay variation (typical)
±150 ns
±500 ns
±500 ns
Far off selectivity
40 dB
60 dB
55 dB
NF at Gmax
8 dB
6 dB
6 dB
NF at Gmax-30 dB
13 dB
12 dB
12 dB
OICP-3 at Gmax
59.0 dBm
59.0 dBm
59.0 dBm
OICP-3 at Gmax -10 dB
58.5 dBm
58.5 dBm
59.0 dBm
OICP-3 at Gmax -20 dB
57.5 dBm
58.0 dBm
58.5 dBm
OICP-3 at Gmax -30 dB
53.0 dBm
55.0 dBm
57.0 dBm
-76 dBm/Hz
-96 dBm/Hz
Power consumtion
(standby/max power)
1 module (typ.cons)
145/220 W
130/210 W
130/210 W
4 modules (typ.cons)
180/270 W
160/240 W
160/240 W
Output noise
in band at Gmax
Output noise out of band
at Gmax
M0079A1A.doc
Id.-No. 151775
Page 64
10-March-00
User’s manual for Repeater MRx01B Power
ELECTRICAL SPECIFICATIONS
MR801Bi Power
Frequency range
Uplink 806-824 MHz; Downlink 851-869 MHz
Useable bandwidth
18 MHz in the upper or lower iDEN band
Gain
90 dB
Gain variation over
frequency and temperature*
± 2.5 dB (± 3.5 dB at extreme temperatures)
Gain adjust range
30 dB in 2 dB steps
Gain adjust range tolerance
± 0.5 dB
Return loss
15 dB @ 25°C ambient temperature
Spurious/intermodulation
-13 dBm max.
Power supply
100 to 130 VAC / 40 - 60 Hz
Option: 220 to 250 VAC / 40 - 60 Hz
Option: 185 to 320Vac, 40 - 65Hz
Option: 24 VDC
Option: ± 42 to ± 60VDC
Option: ± 80 to ± 130VDC
RF connector
7/16 female
Option: N female
Environmental and safety
See separate leaflet
*: Normal temperature range +5° to +40°C; Extreme temperature range -33° to +50°C
AVAILABLE POWER PER TECHNOLOGY
Pout at 1 channel
Pout/channel at 2 channels
Pout/channel at 4 channels
Pout/channel at 8 channels
ALC threshold
M0079A1A.doc
iDEN
37.0 dBm
31.0 dBm
28.0 dBm
25.0 dBm
Id.-No. 151775
Analog
40.0 dBm
37.0 dBm
33.0 dBm
29.0 dBm
Adjustable
Page 65
10-March-00
User’s manual for Repeater MRx01B Power
BAND AND CHANNEL SPECIFICATIONS
Variable Bandwidth
Channel Selective
0.1* to 15.0 MHz
25 kHz
2 MHz
30 dB bandwith
fc ± 60 kHz
50 dB bandwith
fc ± 120 kHz
6 µs
20 µs
± 150 ns
± 500 ns
Far off selectivity
40 dB
50 dB
NF at Gmax
8 dB
6 dB
NF at Gmax-30 dB
13 dB
12 dB
OICP-3 at Gmax
48 dBm
48 dBm
OICP-3 at Gmax -10 dB
48 dBm
48 dBm
OICP-3 at Gmax -20 dB
47 dBm
47 dBm
OICP-3 at Gmax -30 dB
45 dBm
45 dBm
-81 dBm/Hz
-101 dBm/Hz
Power consumtion
(standby/max power)
1 module (typ.cons)
155/220 W
150/210 W
4 modules (typ.cons)
200/265 W
175/240 W
3 dB bandwidth
Slope 3 dB to 30 dB
Delay
Delay variation (typical)
Output noise in band at Gmax
Output noise out of band at Gmax
1.5 dB gain degradation at 100 kHz
M0079A1A.doc
Id.-No. 151775
Page 66
10-March-00
User’s manual for Repeater MRx01B Power
MECHANICAL SPECIFICATIONS
MRx01B Power
The MRx01B Power is available in the G-cabinet
Max. Height x Width x Depth:
21.1 x 18.2 x 7.9 inches
535 x 462.5 x 200 mm
Volume:
approximately 45 litres
Weight:
approximately 103 lbs (47 kg per unit in standard
configuration)
The illustration of chapter provides the dimensions and the view of the layout.
ENVIRONMENTAL AND SAFETY
MRx01B Power
For detailed information refer to the environmental and safety specification leaflet for
MIKOM indoor / outdoor cell enhancers, related to ETS 300019 (European Telecommunication Standard).
Operating temperature (normal temperature range):
(extreme temperature range):
+ 5° C ... + 40° C
- 33° C ... + 50° C
Humidity:
+ 30° C/ 93 %
All data is subject to change without notice !
M0079A1A.doc
Id.-No. 151775
Page 67
10-March-00
User’s manual for Repeater MRx01B Power
9.2
Spare parts lists for MRx01B Power
The following list contains all parts available for the MRx01B Power. The configuration of
the delivered unit meets the requirements of the customer and can differ depending on the
state of delivery.
9.2.1
Spare parts list for MR301B Power
Designation
Id.-No.:
150047
149952
150563
150521
150302
150303
150125
151347
149642
149187
149178
150135
148281
150136
151647
138305
142832
148812
144306
141230
145524
144946
145504
146999
143437
145067
143052
150615
112425
143055
147127
149917
149918
150529
149920
MR301B Power
Assembly drawing
Assembly drawing (RF-cable plan)
Mounting material
Duplexer UL Input
Duplexer DL Input
Bas.Mod.Fix.BW 25,0 MHz
Bas.Mod.Fix.BW 15,0 MHz
Bas.Mod.Fix.BW 12,5 MHz
Bas.Mod.Fix.BW 8,2 MHz
Bas.Mod.Fix.BW 6,0 MHz
Bas.Mod.Var.BW 25,0 MHz
Bas.Mod.Var.BW 10,0 MHz
Ext.Mod.Var.BW 10,0 MHz
Power Amplifierkit 4W
Power Supply, GER plug
Power Supply, UK plug
Power Supply, no plug
Power Supply, no plug
Power Supply, USA plug
Power Supply, no plug
Power Supply, no plug
Power Supply, no plug
M1 Kit 900 MHz
VSWR Kit GSM + EGSM
Ext. Alarms SW-Option
Battery Backup Module
RF Gland / SMA to N
Adapter 7 / 16 male - N female
SW MOB100 V1.10
SW REP1009 V1.11
Modification Kit 1 channel band selective
Modification Kit 2 channels band selective
Modification Kit 3 channels band selective
Modification Kit 4 channels band selective
M0079A1A.doc
Id.-No. 151775
Page 68
10-March-00
User’s manual for Repeater MRx01B Power
Main Board 12V version
Main Board 12V version
Control Unit SM2009
Wall mounting kit
Sparepart kit
Termination Resistor
Ready-made cable AC
Manual MRx01B Power
Manual REP1009V1.xx
Additional information
Assembly guide MRx01B Power
M0079A1A.doc
Id.-No. 151775
149780
149779
143051
146179
146200
33167
143032
151775
148964
148222
151045
Page 69
10-March-00
User’s manual for Repeater MRx01B Power
9.2.2
Spare parts list for MR401B Power
Designation
Id.-No.:
MR401B Power
Assembly drawing
Assembly drawing (RF-cable plan)
Mounting material
Duplexer UL Input
Duplexer DL Input
Bas.Mod.Fix.BW 25,0 MHz
Power Amplifierkit 4W
Power Supply, GER plug
Power Supply, UK plug
Power Supply, no plug
Power Supply, no plug
Power Supply, USA plug
Power Supply, no plug
Power Supply, no plug
Power Supply, no plug
Ext. Alarms SW-Option
Battery Backup Module
RF Gland / SMA to N
Adapter 7 / 16 male - N female
SW MOB100 V1.10
SW REP1009 V1.11
Modification Kit 1 channel band selective
Modification Kit 2 channels band selective
Modification Kit 3 channels band selective
Modification Kit 4 channels band selective
Main Board 12V version
Main Board 12V version
Control Unit SM2009
Wall mounting kit
Sparepart kit
Termination Resistor
Ready-made cable AC
Manual MRx01B Power
Manual REP1009V1.xx
Assembly guide MRx01B Power
M0079A1A.doc
Id.-No. 151775
150043
150044 150045 150046
149952
150563
150521
150304 150306 150308 150300
150305 150307 150309 150301
150141
151648
138305
142832
148812
144306
141230
145524
144946
145504
145067
143052
150615
112425
143055
147127
149917
149918
149919
149920
149780
149779
143051
146179
146200
33167
143032
151775
148964
151045
Page 70
10-March-00
User’s manual for Repeater MRx01B Power
9.2.3
Spare parts list for MR701B Power
Designation
Id.-No.:
MR701B Power
Assembly drawing
Assembly drawing RF
Assembly drawing (RF-cable plan)
Mounting material
PCS-Duplexer UL Input
PCS-Duplexer DL Input
Active Combiner UL
Active Combiner DL
Bas.Mod.Fix.BW 15,0 MHz
Bas.Mod.Fix.BW 5,0 MHz
Bas.Mod.Var.BW 15,0 MHz
Ext.Mod.Fix.BW 15,0 MHz
Basic Module
Extension Module
Basic Module TDMA
Extension Module TDMA
Basic Module CDMA
Extension Module CDMA
Feedforward Amplifier UL
Feedforward Amplifier DL
Power Supply, GER plug
Power Supply, UK plug
Power Supply, no plug
Power Supply, no plug
Power Supply, USA plug
Power Supply, no plug
Power Supply, no plug
Power Supply, no plug
Mobile kit PCS
Ext. Alarms SW-Option
Battery Backup Module
Battery Backup Module, Dummy without Accu
RF Gland / SMA to N
Adapter 7 / 16 male - N female
SW MOB100 V1.10
SW REP1007 V1.12
SW REP1009 V1.11
Modification Kit 1 channel band selective
Modification Kit 2 channels band selective
Modification Kit 3 channels band selective
M0079A1A.doc
Id.-No. 151775
148604
144382
144381
Page 71
148605
149952
151102
150563
150521
144384
144383
148686
148685
148717
148716
151463
151464
148702
148705
148703
148706
148704
148707
148627
148628
138305
142832
148812
144306
141230
145524
144946
145504
150405
147710
143052
143750
150615
112425
143055
145488
147127
149917
149918
149919
151075
151072
151073
10-March-00
User’s manual for Repeater MRx01B Power
Modification Kit 4 channels band selective
Modification kit TDMA for 1+2 channel
Modification kit TDMA for 3+4 channel
Main Board 26V version
Main Board 26V version
Control Unit SM2009
Wall mounting kit
Sparepart kit
Termination Resistor
Ready-made cable DC
Ready-made cable DC act. Com.
Ready-made cable AC
Manual MRx01B Power
Manual REP1007V1.11
Manual REP1009V1.xx
Assembly guide MRx01B Power
M0079A1A.doc
Id.-No. 151775
149920
151135
151136
149778
149777
143051
146179
146200
33167
149648
150753
152024
151775
145956
148964
151045
Page 72
10-March-00
User’s manual for Repeater MRx01B Power
9.2.4
Spare parts list for MR801B Power and MR801Bi Power
Designation
Id.-No.:
MR801B Power / MR801Bi Power
Assembly drawing
Assembly drawing RF
Assembly drawing (RF-cable plan)
Mounting material
Duplexer UL Input
Duplexer DL Input
Active Combiner UL
Active Combiner DL
Bas.Mod.Var.BW 15,0 MHz
Ext.Mod.Var.BW 15,0 MHz
Basic Module TDMA
Extension Module TDMA
Basic Module CDMA
Extension Module CDMA
Basic Module CDMA f1/f2
Basic Module
Extension Module
Feedforward Amplifier UL
Feedforward Amplifier DL
Power Supply, GER plug
Power Supply, UK plug
Power Supply, no plug
Power Supply, no plug
Power Supply, USA plug
Power Supply, no plug
Power Supply, no plug
Power Supply, no plug
Mobile kit PCS, without mobile
Mobile kit PCS, with mobile
Ext. Alarms SW-Option
Battery Backup Module
Battery Backup Module, Dummy without Accu
RF Gland / SMA to N
Adapter 7 / 16 male - N female
SW MOB100 V1.10
SW REP1007 V1.12
SW REP1009 V1.11
Modification Kit 1 channel band selective
Modification Kit 2 channels band selective
Modification Kit 3 channels band selective
M0079A1A.doc
Id.-No. 151775
148613
151270
149952
151102
150563
150521
148334
148333
148688
148687
148715
148944
148712
148710
148713
148709
152228
148335
148336
148960
148959
150150
150151
150152
150153
151232
151233
148629
148630
138305
142832
148812
144306
141230
145524
144946
145504
150404
150407
147710
143052
143750
150615
112425
143055
145488
147127
149917
149918
150529
Page 73
10-March-00
User’s manual for Repeater MRx01B Power
Modification Kit 4 channels band selective
Modification kit TDMA for 1+2 channel
Modification kit TDMA for 3+4 channel
Main Board 26V version
Main Board 26V version
Control Unit SM2009
Wall mounting kit
Sparepart kit
Termination Resistor
Ready-made cable DC
Ready-made cable DC act. Com.
Ready-made cable AC
Manual MRx01B Power
Manual REP1007V1.11
Manual REP1009V1.xx
Assembly guide MRx01B Power
M0079A1A.doc
Id.-No. 151775
149920
151135
151671
149778
149777
143051
146179
146200
33167
149648
150753
152024
151775
145956
148964
151045
Page 74
10-March-00
User’s manual for Repeater MRx01B Power
9.3
Installation drawing of the Repeater
figure 9-1 Installation drawing of the Repeater
M0079A1A.doc
Id.-No. 151775
Page 75
10-March-00
User’s manual for Repeater MRx01B Power
9.4
Top view of the Repeater (left side , exemplary configuration)
figure 9-2 Top view of the Repeater (left side, exemplary configuration)
M0079A1A.doc
Id.-No. 151775
Page 76
10-March-00
User’s manual for Repeater MRx01B Power
9.5
Top view of the Repeater (right side, exemplary configuration)
figure 9-3 Top view of the Repeater (right side, exemplary configuration)
M0079A1A.doc
Id.-No. 151775
Page 77
10-March-00
User’s manual for Repeater MRx01B Power
9.6
One channel configuration – cabling and block diagram
figure 9-4 Cabling of one channel Repeater
M0079A1A.doc
Id.-No. 151775
Page 78
10-March-00
User’s manual for Repeater MRx01B Power
figure 9-5 Block diagram of one channel Repeater
M0079A1A.doc
Id.-No. 151775
Page 79
10-March-00
User’s manual for Repeater MRx01B Power
10 Index
Abbreviations 8
Active combiner 22, 56
Alarm monitoring 46
Alarms
Acknowledgement of 28
External alarms 30
Handling of 28
Indication of 26
List of all alarms 27
ALC 26
Antenna connectors 38, 39
Antenna isolation 40
AT commands 45
Feedforward amplifier 23
25
Gain
Local settings 25, 41
Setting via PC 43
Grounding 37
Health and safety warnings 9
Battery backup 33
BITE 26
46
I²C-Bus 17
Ident numbers 69, 71, 72, 74
Installation
Electrical 38
Mechanical 35
Interfaces 17
RS232 17
International sales offices 11
Channel
Setting via PC 43
Clamping profile 49
Connector types
7/16 female 39
N female 32
Contents of delivery 8
Control module 17
Configuration 19
conversion module 51
LEDs 26
Local settings 41
Maintenance 48
Measurements of
VSWR signals 30
Modem 44
Mother board 15
Mounting brackets 36
DIP-Switch 43
DIP-Switch settings 20
51
Duplexer 14, 21, 51
Optional modules 30
Output DL
external 32
EEPROM 17
Environmental and safety 68
M0079A1A.doc
Id.-No. 151775
Page 80
10-March-00
User’s manual for Repeater MRx01B Power
Setting of operational parameters 40
Setting to work 40
Severity levels 29
Power supply 23
Replacement of 55
Test probes 22
Trouble shooting 46
RAM / RTC battery 50
Remote control 25
Rotary switch
To set the gain 42
M0079A1A.doc
Id.-No. 151775
Page 81
10-March-00

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 81
Creator                         : Microsoft Word
Create Date                     : Monday, November 06, 2000 11:51:10 AM
Title                           : M0079A1A.PDF
Author                          : Unknown
Producer                        : Acrobat PDFWriter 3.02 for Windows
Subject                         : 

EXIF Metadata provided by EXIF.tools