Andrew Wireless System IONM171717P ION-M17P/17P/17P Repeater User Manual Additional information on SM2009

Download:
Mirror Download [FCC.gov]
Document ID	1563735
Application ID	U2wRG9VC9btlvkgJXadOVA==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	164.81kB (2060130 bits)
Date Submitted	2011-10-20 00:00:00
Date Available	2012-01-15 00:00:00
Creation Date	2011-10-20 10:37:03
Producing Software	Acrobat Distiller 9.4.6 (Windows)
Document Lastmod	2011-10-20 10:37:42
Document Title	Additional information on SM2009
Document Creator	Acrobat PDFMaker 9.1 für Word
Document Author:	Raissa Panlilio

Optical Remote Unit
ION™-M17P/17P/17P
(M-Cabinet)
User's Manual
MF0143AWA
User’s Manual for Remote Unit
ION™-M17P/17P/17P
© Copyright 2011 CommScope, Inc.
All rights reserved.
Andrew Solutions is a trademark of CommScope, Inc.
All information contained in this manual has been revised thoroughly. Yet Andrew
Solutions accepts no liability for any omissions or faults.
Andrew Solutions reserves the right to change all hard- and software characteristics
without notice.
Names of products mentioned herein are used for identification purposes only and
may be trademarks and / or registered trademarks of their respective companies.
No parts of this publication may be reproduced, stored in a retrieval system,
transmitted in any form or by any means, electronical, mechanical photocopying,
recording or otherwise, without prior written permission of the publisher.
Andrew Wireless Systems GmbH, 20-October-2011
Page 2
MF0143AWA.doc
TABLE OF CONTENTS
1. GENERAL
1.1.
USED ABBREVIATIONS
1.2.
HEALTH AND SAFETY WARNINGS
1.3.
ABOUT ANDREW SOLUTIONS
1.4.
INTERNATIONAL CONTACT ADDRESSES FOR CUSTOMER SUPPORT
2. FUNCTIONAL DESCRIPTION
11
2.1.
PURPOSE
11
2.2.
ION-M17P/17P/17P
11
2.3.
2.3.1.
2.3.2.
COMPONENTS OF THE ION-M17P/17P/17P REMOTE UNIT
Fan-Protection Kit
Accessories
12
12
12
3. COMMISSIONING
14
3.1.
3.1.1.
3.1.2.
3.1.3.
3.1.4.
MECHANICAL INSTALLATION
General
Wall-Mounting Procedure
Pole-Mounting Procedure
Mounting of Fan Protection
14
14
16
17
19
3.2.
3.2.1.
3.2.2.
3.2.3.
3.2.4.
3.2.5.
ELECTRICAL INSTALLATION
General
Connections
Grounding
Connection of the Antenna Cables
Power Connection
20
20
21
22
23
24
3.3.
3.3.1.
3.3.2.
OPTICAL-FIBRE-CABLE CONNECTION - RULES
Protective Plug
Protective-Tube Kit
25
26
28
3.4.
COMMISSIONING
30
4. ALARMS
34
4.1.
BITE AND ALARMS
34
4.2.
HANDLING OF ALARMS
34
4.3.
ALARM STATUS
34
4.4.
STATUS LED ALARMS
35
4.5.
EXTERNAL ALARM INPUTS AND OUTPUTS
36
4.6.
TROUBLESHOOTING
37
5. MAINTENANCE
38
5.1.
GENERAL
38
5.2.
REPLACING THE FAN UNIT
39
Page 3
User’s Manual for Remote Unit
ION™-M9/18P/21P EP
5.3.
CLEANING THE HEAT SINK
41
6. APPENDIX
42
6.1.
ILLUSTRATIONS
42
6.2.
6.2.1.
6.2.2.
6.2.3.
SPECIFICATIONS
Electrical Specifications
Environmental and Safety Specifications
Mechanical Specifications
43
43
43
43
6.3.
SPARE PARTS
44
7. INDEX
45
FIGURES AND TABLES
figure 3-1 Wall mounting, (metric dimensions).......................................................... 16
figure 3-2 Pole-mounting kit...................................................................................... 17
figure 3-3 Pole mounting (metric dimensions) .......................................................... 18
figure 3-4 Mounting procedure for fan protection, (metric dimensions)..................... 19
figure 3-5 Connector flange of ION-M17P/17P/17P.................................................. 21
figure 3-6 RS232 connector...................................................................................... 22
figure 3-7 Grounding bolt with loosened hex nut ...................................................... 22
figure 3-8 Grounding bolt, schematic view................................................................ 22
figure 3-9 AC mains plug .......................................................................................... 24
figure 3-10 Protective-plug assembly ....................................................................... 26
figure 3-11 Tube-kit installation................................................................................. 29
figure 4-1 Flange connector, 5 poles ........................................................................ 36
figure 4-2 Flange connector, 7 poles ........................................................................ 36
figure 4-3 Alarm inputs and outputs, standard .......................................................... 37
figure 6-1 Installation drawing................................................................................... 42
table 1-1 List of international contact addresses....................................................... 10
table 3-1 Specified torques ....................................................................................... 15
table 3-2 RS232 connector, pin assignment ............................................................. 22
table 4-1 Status LED alarms..................................................................................... 35
Page 4
MF0143AWA.doc
1 General
1. GENERAL
1.1. USED ABBREVIATIONS
3GPP
AC
AIMOS
ALC
BITE
BTS
CE
CD
CPD
DL
DoC
EDGE
EN
EP
ESD
ETS
EU
FRU
GSM
GND
GUI
ICP3
ID No
ION
IP
ISO
LED
LMT
LTE
MIMO
MS
MU
NF
OTRx
PG
PIM
R&TTE
Rev
RF
RU
RX
SNMP
TS
TX
UL
UMTS
UPS
VSWR
W CDMA
WDM
3rd Generation Partnership Project
Alternating current / Direct Current
Andrew Integrated Management and Operating System
Automatic Level Control
Built-In Test Equipment
Base Transceiver Station
"Conformité Européenne" ("European Conformity")
Compact Disk
Channel Power Detection
Downlink
Declaration of Conformity
Enhanced Data Rates for GSM Evolution
European Norm
Extension Port
Electrostatic Discharge
European Telecommunication Standard
Extension Unit
Field Replaceable Unit
Global System for Mobile Communication
Ground
Graphical User Interface
Intercept Point 3rd order
Identification Number
Intelligent Optical Network
Ingress Protection
International Organization for Standardization
Light Emitting Diode
Local Maintenance Terminal
Long Term Evolution
Multiple Input Multiple Output
Mobile Station
Main Unit
Noise Figure
Optical Transceiver = SRMU (Subrack Master Unit)
Packing Gland
Passive Intermodulation
Radio & Telecommunications Terminal Equipment
Revision
Radio Frequency
Remote Unit
Receiver
Simple Network Management Protocol
Technical Specification
Transmitter
Uplink
Universal Mobile Telecommunication System
Uninterruptible Power Supply
Voltage Standing Wave Ratio
Wideband Code Division Multiple Access
Wavelength Division Multiplex
Page 5
User’s Manual for
Remote Unit ION™-M17/17P/17P
1.2. HEALTH AND SAFETY WARNINGS
1. Only suitably qualified personnel is allowed to work on this unit and only after
becoming familiar with all safety notices, installation, operation and maintenance
procedures contained in this manual.
2. Read and obey all the warning labels attached to the unit. Make sure that the
warning labels are kept in a legible condition and replace any missing or
damaged labels.
3. Obey all general and regional installation and safety regulations relating to work
on high voltage installations, as well as regulations covering correct use of tools
and personal protective equipment.
4. Keep operating instructions within easy reach and make them available to all
users.
5. It is the responsibility of the network provider to implement prevention measures
to avoid health hazards which may be associated to radiation from the antenna(s)
connected to the unit.
6. Note for a Class A digital device or peripheral:
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own
expense.
7. Make sure, access is restricted to qualified personnel.
8. Only licence holders for the respective frequency range are allowed to operate
this unit.
9. Corresponding local particularities and regulations must be observed. For national
deviations please refer to the respective documents included in the manual CD
delivered.
10. Use this equipment only for the purpose specified by the manufacturer. Do not
carry out any modifications or fit any spare parts which are not sold or
recommended by the manufacturer. This could cause fires, electric shock or other
injuries.
11. Due to power dissipation, the repeater may reach a very high temperature. Do not
operate this equipment on or close to flammable materials.
Page 6
MF0143AWA.doc
1 General
12. Before opening the unit, disconnect mains.
13. ESD precautions must be observed! Before commencing maintenance work, use
the available grounding system to connect ESD protection measures.
14. This unit complies with European standard EN60950.
15. Make sure the repeater settings are according to the intended use (see also
product information of manufacturer) and regulatory requirements are met.
16. Although the repeater is internally protected against overvoltage, it is strongly
recommended to earth the antenna cables close to the repeater’s antenna
connectors for protection against atmospheric discharge.
17. Laser radiation! Do not stare into the beam; do not view it directly or with optical
instruments.
Page 7
User’s Manual for
Remote Unit ION™-M17/17P/17P
1.3. ABOUT ANDREW SOLUTIONS
Andrew Wireless Systems GmbH based in Buchdorf/ Germany, is a leading
manufacturer of coverage equipment for mobile radio networks, specializing in high
performance, RF and optical repeaters. Our optical distributed networks and RF
repeater systems provide coverage for every application: outdoor use, indoor
installations, tunnels, subways and many more.
Andrew Wireless Systems GmbH has unparalleled experience in providing RF
coverage and capacity solution for wireless networks in both indoor and outdoor
environment and belongs to Andrew Solutions, a CommScope Company.
Andrew Solutions is the foremost supplier of one-stop, end-to-end radio frequency
(RF) solutions. Our products are complete solutions for wireless infrastructure from
top-of-the-tower base station antennas to cable systems and cabinets, RF site
solutions, signal distribution, and network optimization.
Andrew Solutions has global engineering and manufacturing facilities. In addition, it
maintains field engineering offices throughout the world.
We operate a quality management system in compliance with the requirements of
ISO 9001. All equipment is manufactured using highly reliable material. In order to
ensure constant first-rate quality of the products, comprehensive quality monitoring is
conducted at all fabrication stages. Finished products leave the factory only after a
thorough final acceptance test, accompanied by a test certificate guaranteeing
optimal operation.
 Note:
Exceptions of and national deviations from this intended use may be
possible. To observe corresponding local particularities and
regulations, please refer to the respective documents (also in
national language) which are included in the manual CD delivered.
To make the most of this product, we recommend you carefully read the instructions
in this manual and commission the system only according to these instructions.
For technical assistance and support, please also contact the local office or Andrew
Solutions directly at one of the addresses listed in the following chapter.
Page 8
MF0143AWA.doc
1 General
1.4. INTERNATIONAL CONTACT ADDRESSES FOR CUSTOMER SUPPORT
Americas:
Canada
United States
Andrew Solutions Canada
Andrew Solutions,
Andrew LLC, A CommScope Company
Mail
620 North Greenfield Parkway
Garner, NC 27529
U.S.A.
Mail
620 North Greenfield Parkway
Garner, NC 27529
U.S.A.
Phone
+1-905-878-3457 (Office)
+1-416-721-5058 (Mobile)
Phone
+1-888-297-6433
Fax
+1-905-878-3297
Fax
+1-919-329-8950
E-mail
Peter.Masih@commscope.com,
WIsupport.us@commscope.com
E-mail
WIsupport.us@commscope.com
Brazil & South America
Mexico, Central America &
Caribbean region
CommScope Cabos do Brasil Ltda.
Andrew Corporation Mexico,
SA DE CV
Mail
Av. Com. Camilo Julio 1256
Zonal Industrial CP 597
Sorocaba SP 18086-000
Brazil
Mail
Av. Insurgentes Sur 688, Piso 6
Col. Del Valle, CP: 03100
Mexico City
Mexico
Phone
+ 55-15-9104-7722
Phone
+52-55-1346-1900 (Office)
+52-1-55-5419-5260 (Mobile)
Fax
+ 55-15-2102-4001
Fax
+52-55-1346-1901
E-mail
WIsupport@commscope.com
E-mail
WIsupport@commscope.com
APAC Countries:
China, India and Rest of Asia
Andrew International Corporation
Australia & New Zealand
Andrew Corporation (Australia) Pty Ltd.
Mail
Room 915, 9/F
Chevalier Commercial Centre
8 Wang Hoi Rd
Kowloon Bay
Hong Kong
Mail
Unit 1
153 Barry Road
Campbellfield
VIC 3061
Australia
Phone
+852-3106-6100
Phone
+613-9300-7969
Fax
+852-2751-7800
Fax
+613-9357-9110
E-mail
WIsupport.China@commscope.com
E-mail
WIsupport.Australia@commscope.com
Page 9
User’s Manual for
Remote Unit ION™-M17/17P/17P
Europe:
United Kingdom
France
Andrew Solutions UK Ltd
CommScope France
Mail
Unit 15, Ilex Building
Mulberry Business Park
Fishponds Road
Wokingham Berkshire
RG41 2GY
England
Mail
Immeuble Le Lavoisier
4, Place des Vosges
92052 Courbevoie
France
Phone
+44-1189-366-792
Phone
+33-1 82 97 04 00
Fax
+44-1189-366-773
Fax
+33-1 47 89 45 25
E-mail
WIsupport.uk@commscope.com
E-mail
WIsupport@commscope.com
Germany
Czech Republic
Andrew Wireless Systems GmbH
Andrew Solutions Czech Republic
C-Com, spol. s r.o
Mail
Industriering 10
86675 Buchdorf
Germany
Mail
U Moruší 888
53006 Pardubice
Czech Republic
Phone
+49-9099-69-0
Phone
+420-464-6280-80
Fax
+49-9099-69-930
Fax
+420-464-6280-94
E-mail
WIsupport@commscope.com
E-mail
WIsupport@commscope.com
Austria
Switzerland
Andrew Wireless Systems (Austria) GmbH
Andrew Wireless Systems AG
Mail
Weglgasse 10
2320 Wien-Schwechat
Austria
Mail
Tiergartenweg 1
CH-4710 Balsthal
Switzerland
Phone
+43-1706-39-99-10
Phone
+41-62-386-1260
Fax
+43-1706-39-99-9
Fax
+41-62-386-1261
E-mail
WIsupport.austria@commscope.com
E-mail
WIsupport.ch@commscope.com
Italy
Spain and Portugal
Commscope Italy S.r.l., Faenza, Italy
Andrew Solutions España S.A.
A Commscope Company
Mail
Via Mengolina, 20
48018 Faenza (RA)
Italy
Mail
Avda. de Europa, 4 - 2ª pta.
Parque Empresarial La Moraleja
28108 Alcobendas (Madrid)
Spain
Phone
+39-0546-697111
Phone
+34-91-745-20 40
Fax
+39-0546-682768
Fax
+34-91-661-87 02
E-mail
WIsupport.italia@commscope.com
E-mail
WIsupport.iberia@commscope.com
table 1-1 List of international contact addresses
Page 10
MF0143AWA.doc
2 Functional Description
2. FUNCTIONAL DESCRIPTION
2.1. PURPOSE
Cellular telephone systems transmit signals in two directions between base
transceiver station (BTS) and mobile stations (MS) within the signal coverage area.
If weak signal transmissions occur within the coverage area because of indoor
applications, topological conditions or distance from the transmitter, extension of the
transmission range can be achieved by means of an optical distribution system.
Such a system contains an optical Master Unit and several Remote Units. The
number of the Remote Units depends on the hardware and software configuration.
The Remote Units are connected to the Master Unit with optical links. The optical
loss must be less than 10 dB inclusive optical couplers or splitters.
The Master Unit is the connection to the base transceiver stations. The configuration
of a Master Unit depends on the number of the Remote Units and the frequency
range.
WDM (Wave Division Multiplex) filters are integrated in the optical modules. For the
UL, a wavelength within 1540 nm – 1562 nm is used. For the DL, a wavelength of
1310 ±20 nm is used. The maximum output power for the UL and DL is 5.7 mW.
2.2.
ION-M17P/17P/17P
Andrew Solutions ION-M17P/17P/17P is a 3 sector single-box remote unit. It is used
in conjunction with a master unit in the ION optical distribution system. This system
transports 3 sectors (3 x 1700/2100 MHz) simultaneously, providing a cost-effective
solution for distributing capacity from one or more base stations.
The ION-M17P/17P/17P transports signals on the RF layer in a very inexpensive
manner. This means that multiple operators and multiple technologies are moved
simultaneously from a cluster of base stations to a remote location over the same
fibre.
The ION optical distribution system is a cost-effective coverage solution for dense
urban areas, airports, high-rise buildings and other locations where physical
structures increase path loss or provide limited space for installation. It has been
specifically designed to reduce zoning problems and to provide homogeneous
coverage. The compact, mechanical design is specifically architected to mount inside
of or on poles and along side structures in such a way that it has a minimal visual
impact.
The ION-M platform has been specifically tested and optimized for CDMA2000.
Furthermore, it is provisioned for future improvements to the modulation and
frequency bands.
Page 11
User’s Manual for
Remote Unit ION™-M17/17P/17P
The ION is easily set-up and supervised via a graphical user interface (GUI). Remote
units can be commissioned through the use of built-in test equipment. An autolevelling function compensates for the optical link loss making installation easy and
quick.
The entire system may be monitored remotely via an Andrew OMC. This is a
comprehensive management platform with SNMP protocol and X.733 standard
implemented. Should a sophisticated interface not be required, the master unit can
be directly connected to the alarm interface of a base station via relay alarming.

3 sector multi-operator support

Reduced visual impact form factor

Efficient, high power amplifier

Single fibre for multiple sectors

Comprehensive operations and management system for configuration and
alarming

OMC with SNMP according to X.733 standard

Easy installation and commissioning
2.3.
COMPONENTS OF THE ION-M17P/17P/17P REMOTE UNIT
2.3.1. Fan-Protection Kit
In order to protect the fan unit (e.g. against rain), a protective cover to be mounted
over the air inlet is delivered with the unit. For indoor applications, mounting of the
fan-protection kit is not mandatory.
For more details see chapter 3.1.4 Mounting of Fan Protection.
2.3.2. Accessories
For the accessories available for the remote unit, e.g. overcoat housing, connecting
box or iso-trafo kit, a separate manual is available.
Page 12
MF0143AWA.doc
2 Functional Description
For your notes:
Page 13
User’s Manual for
Remote Unit ION™-M17/17P/17P
3. COMMISSIONING
3.1. MECHANICAL INSTALLATION
3.1.1. General
Read the health and safety warnings in chapter 1.2.
1. Do not install the unit in a way or at a place where the specifications
outlined in the Environmental and Safety Specifications leaflet of the
supplier are not met.
2. It is recommended only to use the mounting hardware delivered by the
supplier. If different mounting hardware is used, the specifications for
stationary use of the Remote Unit must not be exceeded.
 Note:
Exceeding the specified load limits may cause the loss of warranty!
3. The unit is considerably heavy. Make sure that a suitable mounting surface
is used. Ensure there is adequate manpower to handle the weight of the
system.
4. Due to power dissipation, the Remote Unit may reach a very high
temperature. Ensure sufficient airflow for ventilation as specified in the
individual mounting procedures.
5. When connecting and mounting the cables (RF, optical, mains, ...) ensure
no water can penetrate into the unit through these cables.
6. Also observe all additional rules or restrictions regarding mounting that
depend on the type of Remote Unit. For details refer to chapter 7.2.2
Mechanical Specification. Install the unit vertically with the fan unit at the
top. A maximum tilt angle of 25° from a vertical position must be kept, as in
the following illustrations:
Page 14
MF0143AWA.doc
3 Commissioning
7. A spacing of 40 mm (1.58 inch) around the unit is required.
8. To ensure sufficient airflow when mounting the unit in enclosed spaces, two
lid openings (one for the air inlet and the other for the air outlet) have to be
provided. Do not block these air inlets and outlets when mounting the
Remote Unit. The size of each opening must equal at least 17 x 17 cm
(290 cm2). Make sure, too, there is no thermal short circuit between the air
inlet and air outlet.
If any different or additional mounting material is used, ensure that the mounting
remains as safe as the mounting designed by the manufacturer. Ensure that the
static and dynamic strengths are adequate for the environmental conditions of the
site. The mounting itself must not vibrate, swing or move in any way that might cause
damage to the Remote Unit.
Specified torques have to be observed for certain mounting procedures according to
the following table:
Type
Thread
Specified torques
Lens head
screws
M4
3.3 Nm
Hex
Spacing
PG
PG
nuts
bolts
(plastic) (aluminium)
M8
M4
M8
PG 13.5 PG 29
27 Nm 2.3 Nm 27 Nm 3.75 Nm 10 Nm
table 3-1 Specified torques
 Note:
To avoid damage when mounting the unit, always make sure that
the M8 washers (DIN9021 or DIN125 depending on the mounting kit)
are placed behind and in front of the mounting drillings of the unit.
The mounting procedures for a stand-alone Remote Unit without optional
accessories are described and illustrated in the following sections. For further
information regarding special mounting procedures including mounting of accessory
equipment, please see separate manual.
Page 15
User’s Manual for
Remote Unit ION™-M17/17P/17P
3.1.2. Wall-Mounting Procedure

Check the suitability of the wall-mounting kit and the wall.

Mark the position of the drilling
holes (for measurements refer to
figure 3-1 Wall mounting). Drill
four holes at the marked positions
and insert dowels *.
Use a cap nut or lock nut to screw
the four dowel screws into the
dowels and put the distance tubes
over the screws.

Hang the mounting brackets of the
Remote Unit into the screws, and
fasten them immediately using the
washers and nuts.

Ensure that there is free access to
the electrical connections as well
as to the cabinet. The approved
bending radius of the connected
cables must not be exceeded.
4.0
0.50
122 ± 0.50
80 ± 0.50
18
796 ± 1.00

Wall mounting with active cooling kit
Mains supply
G0946Z0
figure 3-1 Wall mounting, (metric dimensions)
* The dowels are not part of the delivery since the suitable type depends on the on-site conditions
(material of wall). Therefore, use dowels that are appropriate for the mounting surface.
Page 16
MF0143AWA.doc
3 Commissioning
3.1.3. Pole-Mounting Procedure
Standard mounting hardware cannot be used to mount the Remote Unit to a pole, a
column or other similar structures. Additional hardware must be used for this type of
installation. Such a pole-mounting kit could include two threaded rods M8, two
U-beams and mounting material like bolts and nuts.
figure 3-2 Pole-mounting kit

Use the screw bands to fasten the two U-beams to the pole as illustrated in figure
3-3 Pole mounting.
 Note:

When fastening the U-beams make sure that they are installed
congruently and not at an angle to each other. To determine the
distance between the beams refer to 3.1.2 Wall-Mounting Procedure
for measurements.
Hang the mounting brackets of the Remote Unit into the threaded bolts of the
U-beam, and fasten them immediately using the washers and nuts.
Ensure that there is free access to the electrical connections as well as to the
cabinet. The approved bending radius of the connected cables must not be
exceeded.
Page 17
User’s Manual for
Remote Unit ION™-M17/17P/17P
Lock for folding
screw band ES 119
TESPA screw band,
stainless, 11 mm
Optical
Remote Unit
Washer DIN 125
Form B Ø 8.0
Lock washer for M8.0 DIN 127
A2 Form B
Hexagon nut M8
DIN 934
Ø40
Ø140
Pole
Pole
Pole-mounting
bracket
G0764M6
figure 3-3 Pole mounting (metric dimensions)
Page 18
MF0143AWA.doc
3 Commissioning
3.1.4. Mounting of Fan Protection
Since the fan protection is required for the outdoor usage of a stand-alone Remote
Unit, the mounting of this optional equipment is also described in this manual.

To install the protective cover of the fan protection kit, first unscrew the four
screws with the respective lock washers from the cover of the air inlet of the
Remote Unit, and instead, screw in the four spacing bolts M4.0x30 with the four
lock washers M4.0 DIN125 that are part of the fan protection kit.

Place the protective cover into the right position by fitting its four bore holes over
the spacing bolts and fasten it using the original lock washers and screws of the
Remote Unit. (These lock washers and screws are also part of the fan protection
kit and can be used as spare parts in case of loss.)
remove the screw
and the lock washer!
2x M4.0x8 fillister-head screws
remove the screw
and the lock washer!
2x M4.0x8
fillister-head screws
2x lock washers
2x lock washers
2x washers
2x M4.0x8
fillister-head screws
AIR STREAM
2x M4.0x30
spacing bolts
1x rain protective cover
2x lock washers
2x washers
2x M4.0x8
fillister-head screws
2x M4.0x8
fillister-head screws
156
152
171
2x lock washers
20
remove the screw
and the lock washer!
G0496MF
figure 3-4 Mounting procedure for fan protection, (metric dimensions)
Page 19
User’s Manual for
Remote Unit ION™-M17/17P/17P
3.2. ELECTRICAL INSTALLATION
3.2.1. General
Read the health and safety warnings in chapter 1.2.
1. This unit contains dangerous voltages. Loss of life, severe personal injury or
property damage can be the result if the instructions contained in this manual are
not followed.
2. It is compulsory to ground the unit before connecting power supply. A grounding
bolt is provided on the cabinet to connect the ground-bonding cable.
3. Although the Remote Unit is internally protected against overvoltage, it is strongly
recommended to earth the antenna cables close to the antenna connectors of the
Remote Unit for protection against atmospheric discharge. In areas with strong
lightning it is strongly recommended to insert additional lightning protection.
4. If the mains connector of the Remote Unit is not easily accessible, a disconnect
device in the mains circuit must be provided within easy reach.
5. Before connecting or disconnecting the mains connector at the Remote Unit,
ensure that mains supply is disconnected.
6. Make sure that an appropriate circuit breaker and an overcurrent limiting device
are connected between mains and Remote Unit.
7. A connection of mains supply to a power socket requires the power socket to be
nearby the Remote Unit.
8. Incorrectly wired connections can destroy electrical and electronic components.
9. To avoid corrosion at the connectors caused by electrochemical processes, the
material of the cable connectors must not cause a higher potential difference than
0.6 V (see electrochemical contact series).
10. Use an appropriate torque wrench for the coupling torque of N-type connectors
(2 N-m / 20 in lb), with 13/16 in opening to tighten the N-type antenna connectors.
For example, use torque wrench of item no. 244379 available from the Andrew ecatalog. Do NOT use your hands or any other tool (e.g. a pair of pliers)! This
might cause damage to the connector and lead to a malfunction of the Remote
Unit.
11. For unstabilized electric networks which frequently generate spikes, it is advised
to use a voltage limiting device.
12. The unit complies with the surge requirement according to EN 61000-4-5 (fine
protection); however, it is recommended to install an additional medium (via local
supply connection) and/or coarse protection (external surge protection) depending
on the individual application in order to avoid damage caused by overcurrent.
13. Observe the labels on the front panels before connecting or disconnecting any
cables.
Page 20
MF0143AWA.doc
3 Commissioning
3.2.2. Connections
Mains
connector
Status LED
N-connector
mobile
Sector 3
External
alarm input
Alarm
output
N-connector
mobile
Sector 2
Control
connector
Grounding bolt
Optical-fibre
connector
N-connector mobile
Sector 1
figure 3-5 Connector flange of ION-M17P/17P/17P
Page 21
User’s Manual for
Remote Unit ION™-M17/17P/17P
Control Connector RS232 - Local Interface
This 8-pin male connector (type: Binder Series 712) is primarily to support local
control of the remote unit via RS232 ASCII interface.
PIN
figure 3-6 RS232 connector
Assignment
Not connected (n.c.)
RS232 Rx
RS232 Tx
n.c.
GND* (RS232)
n.c.
n.c.
n.c.
table 3-2 RS232 connector, pin assignment
* GND is the abbreviation of Ground
3.2.3. Grounding
Grounding must be carried out. Connect an earth-bonding cable to the grounding
connection provided at the outside of the remote unit (see chapter 3.2.2
Connections). Do not use the grounding connection to connect external devices.
figure 3-7 Grounding bolt with
loosened hex nut
figure 3-8 Grounding bolt, schematic view
After loosening the hex nut, connect the earth-bonding cable between the two
washers as illustrated in the figures above. Then, fasten all parts again with the hex
nut.
Page 22
MF0143AWA.doc
3 Commissioning
3.2.4. Connection of the Antenna Cables
The Remote Unit has N-type antenna connectors. For its location please refer to
chapter 3.2.2 Connections. For mounting the cable connectors, it is recommended to
refer to the corresponding documentation of the connector manufacturer. The
bending radius of the antenna cables must remain within the given specifications.
For the selection of cable and antenna it should be considered that, on the one hand,
a cable with higher loss is less expensive but, on the other hand, it impairs
performance.
Use an appropriate torque wrench for the coupling torque of N-type
connectors (2 N-m / 20 in lb), with 13/16 in opening to tighten the N-type
antenna connectors. For example, use torque wrench of item no. 244379
available from the Andrew e-catalog. Do NOT use your hands or any
other tool (e.g. a pair of pliers)! This might cause damage to the
connector and lead to a malfunction of the Remote Unit.
To minimize passive inter-modulation (PIM) distortion, attention has to
be paid to the physical condition of the connector junctions. Do not use
connectors that show signs of corrosion on the metal surface. Prevent
the ingress of water into the connector. Attach and torque the
connectors properly.
Page 23
User’s Manual for
Remote Unit ION™-M17/17P/17P
3.2.5. Power Connection
Before connecting electrical power to the units, the system must be grounded as
described in the previous chapter.
Mains power must be connected at the mains connector of the unit (see chapter
3.2.2 Connections).
The power supply plug is part of the delivery. The correct wiring of the power supply
plug is as follows:
figure 3-9 AC mains plug
For the AC power supply connection, a minimum cross section of
1.5 mm2 is required. Each wire must observe the applicable national
regulations regarding loop impedance, voltage drop, and methods of
installation. Make sure to connect the correct voltage to the unit.
 Note:
Do not connect or disconnect the power cord at the mains connector
while power is on. Turn off mains * power before connecting the
power cord at the remote unit, then, engage mains again.
* Mains power must be interruptible with an external mains breaker. For the mains
breaker, observe the following recommendation:
120 Volt / 20 Amp max. or 240 Volt / 16 Amp, single-phase, 50 / 60 Hz AC service is
needed, i.e. the external AC breaker should be 20 Amps max. for 120-Volt service or
16 Amps for 240-Volt service.
Page 24
MF0143AWA.doc
3 Commissioning
3.3. OPTICAL-FIBRE-CABLE CONNECTION - RULES
Optical signals are transmitted by use of optical fibres. When connecting these fibres
observe the following instructions.
 Note:
Care should be taken when connecting and disconnecting fibreoptic cables. Scratches and dust significantly affect system
performance and may permanently damage the connector. Always
use protective caps on fibre-optic connectors not in use.
In general, optical fibres do not need special protective measures. However,
protection against environmental influences e.g. rodents and humidity must be
considered.
The optical fibre is a single mode fibre. Type is E9/125 µm with the following
minimum requirements:
Attenuation: <0.36 dB / km @ 1310 nm
Dispersion: <3.5 ps / nm km @ 1310 nm
<0.26 dB / km @ 1550 nm
<18.0 ps / nm km @ 1550 nm
The specified bending radius of the optical fibres must not be exceeded. The pigtails
for the connection between master unit and remote unit must have a sufficient length.
A protection for the feeding into units must be given. The system attenuation of the
optical fibres, including the connectors, must not exceed 10 dB.
System attenuation and attenuation of optical components must be determined. This
can be achieved by measuring attenuation and reflection with an appropriate
measuring instrument. For pigtails, a total value of < 0.4 dB (measured to a reference
plug) can be assumed due to the dead zone of the reflectometer. These
measurements must be made with a sufficient length of optical fibre, at the input and
output of the device which has to be measured.
Fibre-cable connectors have to be of the same type (E2000APC8°) as the
connectors used for the unit. The fibre-optic cables are connected to the optical
transceiver.
Angled connectors are not compatible with straight optical connectors;
non-compatibility of connectors will result in permanent damage to
both connectors.
Before connecting the fibre cables, follow the procedure below to ensure optimized
performance. It is important for these procedures to be carried out with care:
Page 25
User’s Manual for
Remote Unit ION™-M17/17P/17P

Remove fibre-optic protective caps.

Do not bend the fibre-optic cable in a tight radius (< 4 cm) as this may cause
cable damage and interrupt transmission.

Using high-grade alcohol and lint-free cotton cleaning swabs, clean the end of
the fibre-optic cable that will be inserted in the optical connectors on the donor
interface box.

Blow out the laser receptacle with clean and dry compressed air to remove
any particulate matter.

Connect the fibre-optic cables by inserting the cable end into the laser
receptacle and aligning the key (on the cable end) with the keyed slot.

Do not use any index-matching gels or fluids of any kind in these connectors.
Gels are intended for laboratory use and attract dirt in the field.
3.3.1. Protective Plug
Connection:
A protective plug is provided for the connection of the fibre-optic cables.
figure 3-10 Protective-plug assembly
 Note:
Page 26
Only high-quality connectors must be used for this type of plug.
Qualified brands are Diamond or Huber & Suhner.
MF0143AWA.doc
3 Commissioning
For plug assembly, observe the following instruction:
1. Pass one or two contacts through the
backshell and the clamp ring.
2. Place the contact(s) on the lower insulation body by pushing the groove of the
contact into the cavity. If there is only one contact, cavity A must be used. *
3. Then, mount the upper insulation body on the lower insulation body. **
Upper insulation body
Cavity B
Cavity A
4. Bring the insulator into the plug. The narrow groove of the insulator must be fitted
into the stamp of the plug.
**
To release the contact for disassembling, push the inner snap to the side and pull the contact out.
To release upper and lower insulation bodies for disassembling, use a small screwdriver and
carefully open the snap-connections at the left and the right side of the insulator without
damaging them.
5. Fasten the insulator by screwing the 6. Place the appropriate seal parts (with
backshell tight onto it. Use a spanner
one groove for one contact or two
with opening 32 to screw the
grooves for two contacts) over the
backshell tight (no gap).
cable(s) and push them into the
backshell.
No gap
Seals with
one groove
Page 27
User’s Manual for
Remote Unit ION™-M17/17P/17P
7. Bring the plastic ring over the cable(s), push it into the backshell and compress
the seals and plastic ring by screwing the clamp ring tight (no gap) using a
spanner with opening 20. ***
Screw tight until gap is closed
8. Connect the plug to the optical-fibre 9. To lock the connector, push the black
connector of the remote unit, again by
locking ring forward.****
fitting a stamp on the plug into the
groove of the connector.
Groove
Push forward to lock, pull
back to free connection
*** For disassembling, release the clamping ring and remove the seals and the plastic ring first.
**** Locking mechanism: The system of locking the plug is based on a “push-pull” mechanism. The
locking ring has to be pushed forward to lock the connector and pulled back to free the
connection.
3.3.2. Protective-Tube Kit
As additional protection for the optical fibers, this connector type can be
supplemented by a special tube kit. To fasten the tube correctly, first unscrew the
clamp ring (if already installed) of the original plug kit.
Then, proceed according to the following instruction:
Page 28
MF0143AWA.doc
3 Commissioning
Protective plug
Fiber cable
Ring 3/4
Reducer
Screw the reducer to
the protective plug
backshell without any
gap!
Coupling
Place the appropriate seal
parts (with) one groove for
one contact or two grooves
for two contacts) over the
cable(s) and push them into
the backshell!
Protective tube
Push the fiber-optic cable carefully
through the tube until it comes out
at the other end.
G1055M0
figure 3-11 Tube-kit installation
Page 29
User’s Manual for
Remote Unit ION™-M17/17P/17P
3.4. COMMISSIONING
Read the health and safety warnings in chapter 1.2 as well as the description
carefully to avoid mistakes and proceed step by step as described!

Do not operate the remote unit without terminating the antenna connectors.
The antenna connectors may be terminated by connecting them to their
respective antennas or to a dummy load.

Only qualified personnel should carry out the electrical, mechanical,
commissioning and maintenance activities that require the unit to be powered
on when open.

When opening the remote unit do not damage the warranty labels on the
internal devices. The warranty is void if the seals are broken.

Ensure that all connections have been performed according to chapter 3.2.2
Connections.
Page 30
MF0143AWA.doc
3 Commissioning
Commissioning an ION-M Remote Unit
Manual for Remote
Unit
Philips
screwdriver
Mounting kit
Spanner, size
13 mm
Drilling
machine
Dowels
Screw driver
Screw driver
Spanner, size
13 mm
Start
Preperation
Unpack RU, RU accessories and
mounting kit.
Mechanical installation
Fasten wall or pole mounting kit to wall or
pole.
Mechanical installation
Mount RU to mounting kit, ensure suffient
air flow and avoid thermal short circuits.
Grounding cable
Spanner 13 mm
Electrical connections
Connect grounding cable and
ground the RU.
Alarm kit
(M-cabinet)
External devices
Connect external devices to the external
in or alarm out connectors, or to the
connecting board inside the RU.
RF connection
Connect antenna cable to antenna port.
Optical connections
Mount the optical fibre with E2000 APC8°
connector into the connector. Plug the
connector into the RU.
E2000 APC8° connector
Spanner with opening 32
Mains cable
Connecting kit
Electrical connections
Connect AC (DC) power to the power
cable. Ensure there is a circuit breaker
between mains and RU.
G1055Z0
G1055Z0
Mains
Switch mains power on.
Page 31
User’s Manual for
Remote Unit ION™-M17/17P/17P
LED on?
No
Check power switch inside RU
(RUs with door).
Check mains cabling.
Check mains power.
Yes
LED status
Red
Internal Error
Change power supply (RUs with a
door).
Reduce environmental temperature.
Eliminate thermal short circuit.
Disconnect and connect mains. Fans
should run. If not, replace the fans at
RU.
MU: Change amplifier setting at MU
controller
Orange
Yellow
Yes
LED status
Red
Green
Spare RU
available?
External error
Close the door (RUs with a door).
Check externally connected devices.
Check fibre loss of optical link.
Check optical connectors.
Clean optical connectors.
Check optical output power of corresponding
OTRx at master unit.
ALC alarm: Decrease DL input power of
affected band.
VSWR alarm: Check antenna and cable.
Green
No
Contact customer
service
Finished setting up
all RUs?
No
Yes
Proceed to MU to set up the SW
Go to MU
Page 32
Output:
All RUs okay.
MF0143AWA.doc
3 Commissioning
For your notes:
Page 33
User’s Manual for
Remote Unit ION™-M17/17P/17P
4. ALARMS
4.1. BITE AND ALARMS
The Built-In Test concept comprises the monitoring of the power supplies, the power
amplifiers and the optical interface.
All occurring alarms can be checked via software at the master unit.
4.2. HANDLING OF ALARMS
As soon as the software acknowledges a valid alarm, a message is transmitted to the
master unit.
If the reason for the alarm has been cleared or if the alarm should continue, a new
alarm message will not be repeated. If there was an interruption of at least five
seconds after acknowledgement, a new alarm message will be generated.
4.3. ALARM STATUS
For details refer to the corresponding software documentation of the master unit.
Page 34
MF0143AWA.doc
4 Alarms
4.4. STATUS LED ALARMS
For local supervision, a status LED on the connector flange of the remote unit gives
an indication of possible reasons for alarms. This table shows possible on-site
measures that could be checked before referring to the master unit alarm list.
Status LED Indication
Green
Orange
Red
Status LED off
Alarms
Possible on-site measures
No alarm 
Status ok
Door alarm
Close the door (RUs with door).
Alarms not directly related to RU:
External alarms Check externally connected devices.
Check fibre loss of optical link.
Check optical connectors.
Optical alarm Rx Clean optical connectors.
(MU: Check optical output power of
corresponding OTRx at master unit).
(MU: Decrease DL input power of
ALC alarm
affected band).
Alarms directly related to RU:
Change power supply (RUs with door).
Power 28 V
Replace the affected remote unit.
Reduce environmental temperature.
Temperature
Eliminate thermal short circuit.
Disconnect and connect mains. Fans
Fan
should run. If not, replace the fans at
RU.
I²C
Disconnect and connect mains.
Optical alarm Tx Amplifier “Power (MU: Change amplifier setting at MU
Down”
controller).
Check power switch inside of RU (RUs
with door).
Mains
Check mains cabling.
Check mains power.
table 4-1 Status LED alarms
For the position of the status LED see chapter 3.2.2 Connections.
Explicit troubleshooting is available in the MU software (software manual or WEB
Interface).
Page 35
User’s Manual for
Remote Unit ION™-M17/17P/17P
4.5. EXTERNAL ALARM INPUTS AND OUTPUTS
G1038Z0
figure 4-1 Flange connector, 5 poles
G1038Z0
figure 4-2 Flange connector, 7 poles
The alarm outputs (open collector output 5 V / 1 mA) are normally low. In case of an
alarm they are high active (5 V). They can be used to monitor alarms with an external
alarm indicator.
The +28 V pin (for its location see figure 4-2 Flange connector, 7 poles) is protected
by a 500mA thermoswitch. In case of exceeding this current between pin 7 and GND
and/or in case of a failure of the VSWR module, the thermoswitch turns into a highresistive status. In this case no fuse needs to be replaced. Just wait a few minutes
until the thermoswitch reaches the normal operating temperature again.
 Note:
The manufacturer / supplier of this system accepts no liability for
damage caused by equipment connected to external outputs or by
effects from such equipment.
As accessory equipment the alarm kit (see chapter 6.3 Spare Parts) is available to
connect external devices to the external alarm inputs and outputs..
Page 36
MF0143AWA.doc
4 Alarms
With the external alarm inputs it is possible to monitor the status of connected
devices, e.g. a UPS, via software. All alarm inputs are normally high (5 V) without
connection. The polarity (high/ low) can be set via the software at the Master Unit (for
details please see according software manual).
The device to be monitored must be connected so that the alarm contacts will be
closed in case of an alarm (I max = 8 mA). The alarm inputs are potential-free with
common ground.
Subminiature circular connectors series 712 with five and seven contacts, which are
contained in the alarm kit, can be ordered directly from the Binder Connector Group,
the manufacturer, or indirectly from Andrew Solutions (see chapter 6.3 Spare Parts).
ION-M alarm inputs
ION-M alarm outputs
+5 V
+5 V
560R
4700R
Alarm output
Alarm input
Alarm GND
Alarm GND
Alarm GND
Alarm GND
V1651A1
figure 4-3 Alarm inputs and outputs, standard
4.6.
TROUBLESHOOTING
The status of the remote unit can be checked via the master unit (for details please
refer to the software manual of the Master Controller). Locally, the status can be
checked at the LED, see chapter 4.4 Status LED Alarms.
Page 37
User’s Manual for
Remote Unit ION™-M17/17P/17P
5. MAINTENANCE
5.1. GENERAL
Read the health and safety warnings in chapter 1.2.
 Note:
The remote unit does not require preventative maintenance
measures.
 Note:
To prevent malfunctions of the cooling system due to dirt or
pollution, it is recommended to clean the heat sink at regular
intervals. These cleaning intervals depend mainly on the location
of the remote unit and the corresponding degree of pollution.
Maintenance of the ION-M17P/17P/17P should be performed by replacing only
components that are contained in this chapter. In order to maintain warranty, take
care not to damage unintentionally the seals on the modules.
The spare parts list, consequently, contains only units which can be replaced without
tuning or soldering work.
 Note:
When sending back the unit, use an appropriate packaging, see
chapter 6.2.2 Environmental and Safety Specifications. We
strongly recommend using the original packaging!
 Note:
Defect parts should only be replaced by original parts from the
supplier. All interventions inside the housing are at one’s own risk.
 Note:
During maintenance ensure
disconnected from mains.
 Note:
Before disconnecting any cables, label any unlabelled cables to
ensure correct connection.
the
remote
unit
has
been
For most maintenance procedures appropriate tools are required to ensure correct
handling. All these tools can be ordered from the supplier. For screwing procedures
observe that all our screws have a right-hand thread, i.e. for fastening the screws
turn the tool clockwise and for unscrewing them turn it counter-clockwise.
Due to the design of the remote unit the only component recommended to be
replaced is the fan unit. For replacing any other component, please contact the
supplier.
Page 38
MF0143AWA.doc
5 Maintenance
5.2. REPLACING THE FAN UNIT
Replacement of the fan unit is not required as a preventative measure. Only when an
alarm indicates a malfunctioning of a fan, must the unit be exchanged.
 Note:
Please observe that the fan unit can only be replaced as a whole.
Do not remove the fans separately.
Read the health and safety warnings in chapter 1.2 as well as the instructions in
chapter 5.1 General before starting with the replacement.
1. Switch off the remote unit. Make sure mains is disconnected for the
following replacement procedure. Then, proceed as follows:
2. Loosen the four tallow-drop screws
M4x8 by which the fan plate is
screwed to the cabinet. Remove the
four screws and the corresponding
washers.
3. Remove the fan unit – by putting slight
pressure on the fan plate cover – to a
position that allows access to the fan
connector and the earth-bonding
cable.
4. Unscrew the fan connector and then
disconnect the earth-bonding cable.
Fan-unit connector
Earth-bonding cable
 Note:
To observe the specified torque of 650 Ncm for an M5 thread, use
an appropriate tool for the following screwing procedures.
Page 39
User’s Manual for
Remote Unit ION™-M17/17P/17P
5. To mount the new fan unit, re-connect the earth-bonding cable and the fan
connector (see step 4). Then, place the fan unit back into its original position and
fix it tight as shown below:
6. Screw the whole fan unit to the cabinet with the four tallow-drop screws M4x8
(see step 2). In order not to exceed the specified torque of 330 Ncm, use an
appropriate tool.
Page 40
MF0143AWA.doc
5 Maintenance
5.3. CLEANING THE HEAT SINK
 Note:
Read the health and safety warnings in chapter 1.2 as well as the
instructions in chapter 5.1 General before starting with the
replacement procedure. Then, proceed as follows:
1. Switch off the remote unit. Make sure that mains is disconnected for the following
procedure.
2. Remove the fan plate with the fan unit 3. Use compressed air (max. 5 bar) to
from the remote unit as described in
blow out the heat sink from back to
chapter 5.2 Replacing the Fan Unit,
front:
steps 1 and 2:
Compressed air
(5 bar max.)
Brush (not metallic)
4. In case the dirt cannot be blown out
completely and parts of it stick to the
ribs of the heat sink, clean the parts
concerned carefully from the front
using e.g. a brush. Take care that the
material is not scratched or damaged.
5. After cleaning the heat sink, mount the fan unit again according to chapter 5.2
Replacing the Fan Unit, step 6. Then, switch the remote unit back on.
Page 41
User’s Manual for
Remote Unit ION™-M17/17P/17P
6. APPENDIX
6.1. ILLUSTRATIONS
figure 6-1 Installation drawing
Page 42
MF0143AWA.doc
6 Appendix
6.2.
SPECIFICATIONS
6.2.1. Electrical Specifications
ION-M17P/17P/17P
Electrical
Mains power
85 to 264 Vac
Power supply
Idle
approx. 330 watts
Power consumption
Full load
800 watts
Optical
Connectors
E2000/APC 8°
Optical return loss
45 dB minimum
Fiber type
Single mode E9/125 µm
Optical link budget
0 to 10 dB
Composite input power 2100 MHz
+3 dBm nominal
@ Conversion module master side
+10 dBm max 1)
-19 dBm min 2)
1)
2)
can be compensated by additional attenuation (0 - 7 dB)
can be compensated by additional gain (0 - 22 dB)
All data is subject to change without notice.
6.2.2. Environmental and Safety Specifications
 Note:
For detailed information, please refer to the Environmental and
Safety Specifications leaflet of the supplier, related to ETS 300 019
(European Telecommunication Standard).
Operating temperature range
RF part
Ingress protection
Fan part
-33° C to +50° C
IP67
IP55
All figures are typical values unless otherwise stated.
All data is subject to change without notice.
6.2.3. Mechanical Specifications
Height, width, depth **
Weight
**
831 x 156 x 147 mm (32.7 x 6.1 x 5.8 in)
18 kg (39.7 Ib)
Spacing required 40 mm (1.58 in) around unit
All data is subject to change without notice.
Page 43
User’s Manual for
Remote Unit ION™-M17/17P/17P
6.3.
SPARE PARTS
The following list contains all parts available for the Remote Unit. The configuration of
the delivered unit meets the requirements of the customer and can differ depending
on the state of the delivery.
Maintenance of the ION-M17P/17P/17P should be performed on an FRU (Field
Replaceable Unit) basis only. Do not damage the warranty labels on the
components, as this voids the warranty.
If any FRU not contained in the following list needs to be replaced, please contact
customer service for additional instructions.
Spare Parts List of the Remote Unit ION-M17P/17P/17P
Designation:
ID No:
ION-M17P/17P/17P
Protective Plug E 2000
Protective Cap E 2000
Fan Protection Kit
Fan Unit
Protective Tube Kit
Manuals for Optical Remote Unit ION-M17P/17P/17P
7634986
7160013
7158914
7159097
7158254
7162182
7619958-00
Accessories
Alarm Kit
7157396
Wall Mounting
Wall-Mounting Kit
ISO Trafo Kit 115 V Wall Mounting
ISO Trafo Kit 230 V Wall Mounting
Connecting Box Kit Wall Mounting
Overcoat Housing Kit Wall Mounting
Pole Mounting
Pole-Mounting Kit
ISO Trafo Kit 115 V Pole Mounting
ISO Trafo Kit 230 V Pole Mounting
Connecting Box Kit Pole Mounting
Overcoat Housing Kit Pole Mounting
7158078
7159340
7158322
7159613
7159625
7157782
7159623
7159621
7159612
7159624
The manufacturer reserves the right to replace the spare parts listed above by
equivalent substitutes.
 Note: Only the spare parts listed above are FRUs (= Field Replaceable
Units) and can be replaced by the user. For replacement of any other
parts, please send the entire Remote Unit back to the manufacturer.
Page 44
MF0143AWA.doc
7 Index
7. INDEX
Address of Andrew Wireless Systems GmbH....... 10
Alarms
Alarm Status .................................................... 35
Bite and Alarms ............................................... 35
External Inputs........................................... 37, 38
Handling of Alarms .......................................... 35
List ................................................................... 38
Outputs ...................................................... 37, 38
RU ................................................................... 38
Status LED....................................................... 35
Andrew Solutions.................................................... 8
Health and Safety Warnings................................... 6
Cleaning the Heat Sink ......................................... 42
Commissioning
General ............................................................ 31
Components
Accessories ..................................................... 12
Fan-Protection Kit ............................................ 12
Connection Rules
Optical-Fibre Cables ........................................ 26
Connections
Antenna ........................................................... 24
Connector Flange ............................................ 22
Optical-Fibre Cable.......................................... 26
Power .............................................................. 25
Contact Addresses ................................................. 9
Customer Support Addresses................................. 9
External Inputs
Location ........................................................... 22
Flange Connector
5 poles ............................................................. 37
7 poles ............................................................. 37
Grounding............................................................. 23
Illustrations ........................................................... 43
Installation
Electrical .......................................................... 20
Mechanical ...................................................... 14
Maintenance......................................................... 39
Mounting
Fan Protection ................................................. 19
Pole (Outside).................................................. 17
Wall.................................................................. 16
Optical-Fibre Connection
Protective Plug ................................................ 27
Protective-Tube Kit .......................................... 29
Outputs
Location ........................................................... 22
Pin Assignment
External Alarms ............................................... 37
Replacement of Fan Unit...................................... 40
Spare Parts .......................................................... 45
Specifications
Electrical .......................................................... 44
Environmental and Safety................................ 44
Mechanical ...................................................... 44
Troubleshooting.................................................... 38
Page 45

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : Raissa Panlilio
Comments                        : 
Company                         : Mikom GmbH
Create Date                     : 2011:10:20 10:37:03+02:00
Modify Date                     : 2011:10:20 10:37:42+02:00
Source Modified                 : D:20111020081518
Subject                         : 
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Producer                        : Acrobat Distiller 9.4.6 (Windows)
Keywords                        : 
Creator Tool                    : Acrobat PDFMaker 9.1 für Word
Metadata Date                   : 2011:10:20 10:37:42+02:00
Format                          : application/pdf
Creator                         : Raissa Panlilio
Title                           : Additional information on SM2009
Description                     : 
Document ID                     : uuid:66ca4b9d-1b99-4eb4-b6b8-f13776deb960
Instance ID                     : uuid:e583380f-993f-45ed-a3e3-53fe1ef6670a
Page Layout                     : OneColumn
Page Count                      : 45

EXIF Metadata provided by EXIF.tools