Appareo Systems 000034 Wireless embedded computer with Cellular/Satellite /WiFi/BT and M2M transmitter User Manual

Appareo Systems, LLC Wireless embedded computer with Cellular/Satellite /WiFi/BT and M2M transmitter

User Manual

 This document and the information contained herein are the property of Appareo Systems, LLC and are confidential. They may not be disseminated or redistributed without the written permission of Appareo Systems, LLC APPAREO SYSTEMS, LLC FARGO, NORTH DAKOTA 58102 Harvey Installation Manual DOCUMENT NUMBER 600840-000041 Document Type Manual Last Revised 4/20/17 REV 1.0 Sheet 1 of 11  600840-000041 Harvey Installation Manual Harvey, Gateway High Spec, GW 400, GW 410, and GW 411
 600840-000041 Gateway Installation Manual Rev: 1.0 Last Revised: 4/21/17   Document Number: 600840-000038 Page 2 of 11  Record of Revisions Revision Number Change Description Effective Date Inserted By 1.0 Initial draft 12/4/18 Lee Hinsz
 600840-000041 Gateway Installation Manual Rev: 1.0 Last Revised: 4/21/17   Document Number: 600840-000038 Page 3 of 11  Table of Contents List of Figures ............................................................................................................................ 4 List of Tables ............................................................................................................................. 4 1. SYSTEM OVERVIEW .......................................................................................................... 5 2. PURPOSE ........................................................................................................................... 5 3. GENERAL INFORMATION .................................................................................................. 5 3.1. SPECIAL TOOLS REQUIRED ................................................................................. 5 3.2. INSTALLATION INSTRUCTIONS OVERVIEW ........................................................ 6 3.3. PARTS LIST FOR INSTALLATION .......................................................................... 6 3.4. HARDWARE COMPONENTS BACKGROUND ........................................................ 7 3.4.1. Electrical Characteristics ................................................................................... 7 3.4.2. Weight and Balance Information ........................................................................ 7 3.4.3. Equipment Dimensions ..................................................................................... 7 3.4.4. Conditions for operation .................................................................................... 7 4. CONFIGURATION ............................................................................................................... 8 4.1. Gateway System Separation Distances .................................................................... 8 4.2. Gateway System Separation Distance Illustration .................................................... 9 5. REgulatory Information ........................................................................................................10 5.1. Federal Communications Commission Notification to User .....................................10 5.2. industry Canada Notifications to User ......................................................................10
 600840-000041 Gateway Installation Manual Rev: 1.0 Last Revised: 4/21/17   Document Number: 600840-000038 Page 4 of 11  List of Figures Figure 1 Separation Distance ..................................................................................................... 9  List of Tables Table 1 System Component Minimum Spacing .......................................................................... 6 Table 2 Parts List for Installation ................................................................................................ 6 Table 3 Weight and Balance Information.................................................................................... 7 Table 4 Equipment Dimensions ................................................................................................. 7 Table 5 Separation Distance ...................................................................................................... 8
 Installation Manual Rev: 1.2 Last Revised: 3/22/16   Document Number: 600840-000038 Page 5 of 11  1.  SYSTEM OVERVIEW Harvey is an embedded computer that provides interfacing capability among a variety of wired and wireless networks.  It implements cellular designs, Bluetooth, WIFI, 433-MHz radio, and Satcom interfaces. Hardline configuration include CAN, RS485, K-Line, RS232, and Broad Reach Ethernet   2.  PURPOSE This Installation Manual is intended to inform installers and users of the proper placement, configuration and distances between system components.  3.  GENERAL INFORMATION 3.1.  SPECIAL TOOLS REQUIRED In addition to SAE standard and/or metric wrenches, sockets, and screw drivers, the following tool are required: 1)  Torque Wrench (in-lbs) 2)  Wrench set
 Installation Manual Rev: 1.2 Last Revised: 3/22/16   Document Number: 600840-000038 Page 6 of 11   3.2.  INSTALLATION INSTRUCTIONS OVERVIEW System installation is accomplished in the following steps: 1)  Installation of Gateway into the tractor cab headliner a.  Torque the antenna terminations to Gateway RF SMA connectors with a torque spec of 7-10 in-lbs +/- 0.5 in-lbs. Mount the Gateway enclosure to the cab with ¼” or 6-mm fasteners and a torque of 30 in-lbs. 2)  Installation of Antennas a.  Find a location on the equipment such that the following distances are the minimum spacing between system components. Table 1 System Component Minimum Spacing  Operator  Gateway Antenna Hub 1  (Recommended minimum spacing between antenna hubs is 7.5 cm) 30 cm ( in USA)  40 cm (in Canada) 20 cm Antenna Hub 2 30 cm (USA) 40 cm (in Canada) 20 cm Gateway 20 cm N/A  b.  Ensure the 433 MHZ antenna have a ground place of 300 x 300 mm for the mounting. c.  Torque the antenna mounting nut (M14x1) to 30 +/- 0.5 in-lbs.     3.3.  PARTS LIST FOR INSTALLATION The following parts are required for the installation of Gateway. Table 2 Parts List for Installation Parts List for Installation Item Nomenclature Part Number QTY 1 Gateway 153010-000069 or 153010-000070 1
 Installation Manual Rev: 1.2 Last Revised: 3/22/16   Document Number: 600840-000038 Page 7 of 11  2 Antenna Hub 1 HCEL-S2-0164A-00_Rev0 4G CELL-433MHz-WLAN  1 3 Antenna Hub 2 HIRD-S2-0146A-0_RevA Iridium-GNSS-4G 1  3.4.  HARDWARE COMPONENTS BACKGROUND 3.4.1. Electrical Characteristics Input Power Requirements:    9-16 VDC Current Draw at 14VDC:    250mA (nominal) 3.4.2. Weight and Balance Information The total weight of the Gateway and antenna is listed below. Table 3 Weight and Balance Information Component Weight (oz) Weight (lbs) Gateway 70.544 4.409 Antenna Hub 1 (HCEL-S2-0164A-01 ) 26.624 1.664 Antenna Hub 2 (HIRD-S2-0146A-01) 26.624 1.664  3.4.3. Equipment Dimensions Equipment dimensions are outlined in the table below for all required components in Gateway. All figures given are representative of maximum equipment dimensions (where applicable).  Table 4 Equipment Dimensions Component Length (mm) Width (mm) Height (mm) Gateway 165 159 54 Antenna Hub 1 (HCEL-S2-0164A-01 ) 124.3 80.3 80.3 Antenna Hub 2 (HIRD-S2-0146A-01) 124.3 80.3 80.3  3.4.4.  Conditions for operation IMPORTANT NOTICE!!!!  This device can be configured to transmit on the 433 MHz frequency following the requirements of 15.231(a-d). This requirement is that the transmission must be used as a control signal.  It can include data transmission as well, or not, but in all cases it must be a control signal.  Failure to adhere to this requirement void’s the authority to operate the equipment.
 Installation Manual Rev: 1.2 Last Revised: 3/22/16   Document Number: 600840-000038 Page 8 of 11           4.  CONFIGURATION With equipment installed, final configuration must meet the minimum separation distance in Table 5 and Section 4.2. 4.1.  HARVEY SYSTEM SEPARATION DISTANCES  Operator  Gateway Antenna Hub 1, 2 (Recommended minimum spacing between antenna hubs is 7.5 cm) 40 cm (USA) 40 cm (Canada)  20 cm Harvey 20 cm N/A Table 5 Separation Distance
 Installation Manual Rev: 1.2 Last Revised: 3/22/16   Document Number: 600840-000038 Page 9 of 11    4.2.  HARVEY SYSTEM SEPARATION DISTANCE ILLUSTRATION Harvey and the following components must follow the distances in the following illustration to comply with FCC part 1.310 and ISED RSS-102.  Note: To adhere with RF exposure requirement, the equipment is intended for PROFESSIONAL INSTALLATION ONLY.  Operator                                                               Antenna Hub 1  Antenna Hub 2 40 cm (USA) 40 cm (Canada)  20 cm  20 cm  20 cm  Figure 1 Separation Distance 40 cm (USA) 40 cm (Canada)  Gateway
 Installation Manual Rev: 1.2 Last Revised: 3/22/16   Document Number: 600840-000038 Page 10 of 11  5.  REGULATORY INFORMATION 5.1.  FEDERAL COMMUNICATIONS COMMISSION NOTIFICATION TO USER Harvey, Gateway High Spec, GW 400, GW 410, and GW 411  These devices comply with Part 15 of the Federal Communications Commission (FCC) Rules. Operation is subject to the following two conditions: (1) These devices may not cause harmful interference, and (2) these devices must accept any interference received, including interference that may cause undesired operation.  These devices must be operated as supplied by Appareo Systems LLC. Any changes or modifications made to these devices without the express written approval of Appareo Systems LLC may void the user’s authority to operate these devices.  This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, no guarantee shall be made that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  • Reorient or relocate the receiving antenna.  • Increase the separation between the equipment and receiver.  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  • Consult the dealer or an experienced radio/TV technician for help.  5.2.  INDUSTRY CANADA NOTIFICATIONS TO USER Harvey, Gateway High Spec, GW 400, GW 410, and GW 411 English  These devices complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.  Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
 Installation Manual Rev: 1.2 Last Revised: 3/22/16   Document Number: 600840-000038 Page 11 of 11  French  Ces appareils sont conformes aux normes RSS sans licence d'Industrie Canada. Son fonctionnement est soumis aux deux conditions suivantes: (1) cet appareil ne doit pas causer d’interférences et (2) cet appareil doit accepter toute interférence, y compris les interférences pouvant entraîner un fonctionnement non souhaité de l’appareil.  Selon les réglementations d'Industrie Canada, cet émetteur radio ne peut fonctionner qu'avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Pour réduire le risque de brouillage radioélectrique causé aux autres utilisateurs, le type d’antenne et son gain doivent être choisis de manière à ce que la puissance rayonnée isotrope équivalente (e.i.r.p.) ne soit pas supérieure à celle nécessaire au succès de la communication.

Navigation menu