Appareo Systems 000034 Wireless embedded computer with Cellular/Satellite /WiFi/BT and M2M transmitter User Manual

Download:
Mirror Download [FCC.gov]
Document ID	4119656
Application ID	jgI8kcC5rkH+6JUPMllU+Q==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	17.13kB (214155 bits)
Date Submitted	2018-12-27 00:00:00
Date Available	2018-12-31 00:00:00
Creation Date	2018-12-19 17:48:37
Producing Software	Microsoft® Word 2016
Document Lastmod	2018-12-19 17:48:37
Document Title	User Manual
Document Creator	Microsoft® Word 2016
Document Author:	Angela Lorenz

600840-000041 Harvey Installation Manual
Harvey, Gateway High Spec, GW 400, GW 410, and GW 411
APPAREO SYSTEMS, LLC
This document and the information
contained herein are the property of
Appareo Systems, LLC and are
confidential. They may not be disseminated
or redistributed without the written
permission of Appareo Systems, LLC
DOCUMENT NUMBER
600840-000041
FARGO, NORTH DAKOTA 58102
Harvey Installation Manual
Document Type
Manual
Last Revised
4/20/17
REV
1.0
Sheet
1 of 11
600840-000041 Gateway Installation Manual
Rev: 1.0
Last Revised: 4/21/17
Record of Revisions
Revision
Number
Change Description
Effective
Date
Inserted By
1.0
Initial draft
12/4/18
Lee Hinsz
Document Number: 600840-000038
Page 2 of 11
600840-000041 Gateway Installation Manual
Rev: 1.0
Last Revised: 4/21/17
Table of Contents
List of Figures ............................................................................................................................ 4
List of Tables ............................................................................................................................. 4
1. SYSTEM OVERVIEW .......................................................................................................... 5
2. PURPOSE ........................................................................................................................... 5
3. GENERAL INFORMATION .................................................................................................. 5
3.1.
SPECIAL TOOLS REQUIRED ................................................................................. 5
3.2.
INSTALLATION INSTRUCTIONS OVERVIEW ........................................................ 6
3.3.
PARTS LIST FOR INSTALLATION .......................................................................... 6
3.4.
HARDWARE COMPONENTS BACKGROUND ........................................................ 7
3.4.1.
Electrical Characteristics ................................................................................... 7
3.4.2.
Weight and Balance Information........................................................................ 7
3.4.3.
Equipment Dimensions ..................................................................................... 7
3.4.4.
Conditions for operation .................................................................................... 7
4. CONFIGURATION ............................................................................................................... 8
4.1.
Gateway System Separation Distances .................................................................... 8
4.2.
Gateway System Separation Distance Illustration .................................................... 9
5. REgulatory Information........................................................................................................10
5.1.
Federal Communications Commission Notification to User .....................................10
5.2.
industry Canada Notifications to User......................................................................10
Document Number: 600840-000038
Page 3 of 11
600840-000041 Gateway Installation Manual
Rev: 1.0
Last Revised: 4/21/17
List of Figures
Figure 1 Separation Distance ..................................................................................................... 9
List of Tables
Table 1 System Component Minimum Spacing .......................................................................... 6
Table 2 Parts List for Installation ................................................................................................ 6
Table 3 Weight and Balance Information.................................................................................... 7
Table 4 Equipment Dimensions ................................................................................................. 7
Table 5 Separation Distance ...................................................................................................... 8
Document Number: 600840-000038
Page 4 of 11
Installation Manual
Rev: 1.2
Last Revised: 3/22/16
1.
SYSTEM OVERVIEW
Harvey is an embedded computer that provides interfacing capability among a variety of wired
and wireless networks. It implements cellular designs, Bluetooth, WIFI, 433-MHz radio, and
Satcom interfaces. Hardline configuration include CAN, RS485, K-Line, RS232, and Broad
Reach Ethernet
2.
PURPOSE
This Installation Manual is intended to inform installers and users of the proper placement,
configuration and distances between system components.
3.
GENERAL INFORMATION
3.1. SPECIAL TOOLS REQUIRED
In addition to SAE standard and/or metric wrenches, sockets, and screw drivers, the following
tool are required:
1) Torque Wrench (in-lbs)
2) Wrench set
Document Number: 600840-000038
Page 5 of 11
Installation Manual
Rev: 1.2
Last Revised: 3/22/16
3.2. INSTALLATION INSTRUCTIONS OVERVIEW
System installation is accomplished in the following steps:
1) Installation of Gateway into the tractor cab headliner
a. Torque the antenna terminations to Gateway RF SMA connectors with a torque
spec of 7-10 in-lbs +/- 0.5 in-lbs. Mount the Gateway enclosure to the cab with ¼”
or 6-mm fasteners and a torque of 30 in-lbs.
2) Installation of Antennas
a. Find a location on the equipment such that the following distances are the
minimum spacing between system components.
Table 1 System Component Minimum Spacing
Antenna Hub 1
(Recommended minimum
spacing between antenna
hubs is 7.5 cm)
Operator
Gateway
30 cm ( in USA)
20 cm
40 cm (in Canada)
Antenna Hub 2
30 cm (USA)
20 cm
40 cm (in Canada)
Gateway
20 cm
N/A
b. Ensure the 433 MHZ antenna have a ground place of 300 x 300 mm for the
mounting.
c. Torque the antenna mounting nut (M14x1) to 30 +/- 0.5 in-lbs.
3.3. PARTS LIST FOR INSTALLATION
The following parts are required for the installation of Gateway.
Table 2 Parts List for Installation
Parts List for Installation
Item
Nomenclature
Gateway
Document Number: 600840-000038
Part Number
153010-000069 or
153010-000070
QTY
Page 6 of 11
Installation Manual
Rev: 1.2
Last Revised: 3/22/16
Antenna Hub 1
HCEL-S2-0164A00_Rev0 4G CELL433MHz-WLAN
Antenna Hub 2
HIRD-S2-0146A0_RevA IridiumGNSS-4G
3.4. HARDWARE COMPONENTS BACKGROUND
3.4.1. Electrical Characteristics
Input Power Requirements:
Current Draw at 14VDC:
9-16 VDC
250mA (nominal)
3.4.2. Weight and Balance Information
The total weight of the Gateway and antenna is listed below.
Table 3 Weight and Balance Information
Component
Weight (oz)
Gateway
Antenna Hub 1 (HCEL-S2-0164A-01 )
Antenna Hub 2 (HIRD-S2-0146A-01)
70.544
26.624
26.624
Weight (lbs)
4.409
1.664
1.664
3.4.3. Equipment Dimensions
Equipment dimensions are outlined in the table below for all required components in Gateway.
All figures given are representative of maximum equipment dimensions (where applicable).
Table 4 Equipment Dimensions
Component
Gateway
Antenna Hub 1 (HCEL-S2-0164A-01 )
Antenna Hub 2 (HIRD-S2-0146A-01)
Length
(mm)
165
124.3
124.3
Width
(mm)
159
80.3
80.3
Height
(mm)
54
80.3
80.3
3.4.4. Conditions for operation
IMPORTANT NOTICE!!!!
This device can be configured to transmit on the 433 MHz frequency following the requirements
of 15.231(a-d). This requirement is that the transmission must be used as a control signal. It
can include data transmission as well, or not, but in all cases it must be a control signal. Failure
to adhere to this requirement void’s the authority to operate the equipment.
Document Number: 600840-000038
Page 7 of 11
Installation Manual
Rev: 1.2
Last Revised: 3/22/16
4.
CONFIGURATION
With equipment installed, final configuration must meet the minimum separation distance in
Table 5 and Section 4.2.
4.1. HARVEY SYSTEM SEPARATION DISTANCES
Antenna Hub 1, 2
(Recommended minimum
spacing between antenna
hubs is 7.5 cm)
Harvey
Operator
Gateway
40 cm (USA)
20 cm
40 cm (Canada)
20 cm
N/A
Table 5 Separation Distance
Document Number: 600840-000038
Page 8 of 11
Installation Manual
Rev: 1.2
Last Revised: 3/22/16
4.2. HARVEY SYSTEM SEPARATION DISTANCE ILLUSTRATION
Harvey and the following components must follow the distances in the following illustration to
comply with FCC part 1.310 and ISED RSS-102.
Note: To adhere with RF exposure requirement, the equipment is intended for PROFESSIONAL
INSTALLATION ONLY.
40 cm (USA)
40 cm (Canada)
40 cm (USA)
40 cm (Canada)
Operator
20 cm
Antenna Hub 1
Antenna Hub 2
20 cm
20 cm
Gateway
Figure 1 Separation Distance
Document Number: 600840-000038
Page 9 of 11
Installation Manual
Rev: 1.2
Last Revised: 3/22/16
5.
REGULATORY INFORMATION
5.1. FEDERAL COMMUNICATIONS COMMISSION NOTIFICATION TO
USER
Harvey, Gateway High Spec, GW 400, GW 410, and GW 411
These devices comply with Part 15 of the Federal Communications Commission (FCC) Rules.
Operation is subject to the following two conditions: (1) These devices may not cause harmful
interference, and (2) these devices must accept any interference received, including
interference that may cause undesired operation.
These devices must be operated as supplied by Appareo Systems LLC. Any changes or
modifications made to these devices without the express written approval of Appareo Systems
LLC may void the user’s authority to operate these devices.
This equipment has been tested and found to comply with the limits for Class B digital devices,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, no
guarantee shall be made that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
5.2. INDUSTRY CANADA NOTIFICATIONS TO USER
Harvey, Gateway High Spec, GW 400, GW 410, and GW 411
English
These devices complies with Industry Canada licence-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this device may not cause interference, and (2) this
device must accept any interference, including interference that may cause undesired operation
of the device.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of
a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To
reduce potential radio interference to other users, the antenna type and its gain should be so
chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary
for successful communication.
Document Number: 600840-000038
Page 10 of 11
Installation Manual
Rev: 1.2
Last Revised: 3/22/16
French
Ces appareils sont conformes aux normes RSS sans licence d'Industrie Canada. Son
fonctionnement est soumis aux deux conditions suivantes: (1) cet appareil ne doit pas causer
d’interférences et (2) cet appareil doit accepter toute interférence, y compris les interférences
pouvant entraîner un fonctionnement non souhaité de l’appareil.
Selon les réglementations d'Industrie Canada, cet émetteur radio ne peut fonctionner qu'avec
une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie
Canada. Pour réduire le risque de brouillage radioélectrique causé aux autres utilisateurs, le
type d’antenne et son gain doivent être choisis de manière à ce que la puissance rayonnée
isotrope équivalente (e.i.r.p.) ne soit pas supérieure à celle nécessaire au succès de la
communication.
Document Number: 600840-000038
Page 11 of 11

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : No
Page Count                      : 11
Language                        : en-US
Tagged PDF                      : Yes
XMP Toolkit                     : 3.1-701
Producer                        : Microsoft® Word 2016
Creator                         : Angela Lorenz
Creator Tool                    : Microsoft® Word 2016
Create Date                     : 2018:12:19 17:48:37-06:00
Modify Date                     : 2018:12:19 17:48:37-06:00
Document ID                     : uuid:C9D24E63-1E3A-43C9-9B86-95773CEC6B7B
Instance ID                     : uuid:C9D24E63-1E3A-43C9-9B86-95773CEC6B7B
Author                          : Angela Lorenz

EXIF Metadata provided by EXIF.tools