Argox Information Co PI-1X60 Data Collector User Manual PI 1060 UserMan 20181005

Argox Information Co Ltd Data Collector PI 1060 UserMan 20181005

PI-1060- UserMan-20181005

Download: Argox Information Co PI-1X60 Data Collector User Manual PI 1060 UserMan 20181005
Mirror Download [FCC.gov]Argox Information Co PI-1X60 Data Collector User Manual PI 1060 UserMan 20181005
Document ID4032108
Application IDkBv1qlTczcQnbhxu+Ccn7g==
Document DescriptionPI-1060- UserMan-20181005
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize134.11kB (1676321 bits)
Date Submitted2018-10-11 00:00:00
Date Available2018-10-12 00:00:00
Creation Date2018-10-04 17:56:27
Producing SoftwareAcrobat Distiller 17.0 (Windows)
Document Lastmod2018-10-04 17:56:27
Document TitleMicrosoft Word - PI-1000 Series user manual_EN Draft 20181002
Document CreatorPScript5.dll Version 5.2.2
Document Author: A316154

PI‐1000 Series
Portable data terminal
User’s Manual
PI‐1010/PI‐1030/PI‐1060/PI‐1230
http://www.argox.com
service@argox.com
V1.2 05‐06‐2018
Regulatory Compliance
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE
STATEMENT
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
‐Reorient or relocate the receiving antenna.
‐Increase the separation between the equipment and receiver.
‐Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
‐Consult the dealer or an experienced radio/ TV technician for
help.
CAUTION:
Any changes or modifications not expressly approved by the
grantee of this device could void the user's authority to operate
the equipment.
PI-1010 EN 300 328 BT RF Power EIRP 1.92 dbm
PI-1060 EN 300 328 BT RF Power EIRP 1.92 dbm
PI-1060 EN 300 200 SUB-1G RF Power EIRP 5.17 dbm
PI-1030 EN 300 328 BT RF Power EIRP 1.92 dbm
PI-1030 EN 300 328 WIFI RF Power EIRP 19.04 dbm
PI-1230 EN 300 328 BT RF Power EIRP 1.92 dbm
PI-1230 EN 300 328 WIFI RF Power EIRP 19.04 dbm
RF exposure warning
The equipment complies with FCC RF exposure limits set
forth for an uncontrolled environment.
The equipment must not be co‐located or operating in
conjunction with any other antenna or transmitter.
ii
Radio Transmitters (Part 15)
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any
interference received including interference that may cause
undesired operation.
FCC ID:NBF‐PI‐1X30 For PI‐1010 & PI‐1030 & PI‐1230
FCC ID:NBF‐PI‐1X60 For PI‐1060
Note:PI‐1060 Only BT & Sub‐1G RF Function
CAUTION: EXPLOSION HAZARD
Do not disassemble, short circuit, heat the battery or dispose of in fire. Store battery
pack in a proper place. Do not expose to temperature above 60℃/140℉. Use specified
charger only. Please dispose of the used batteries following the rules or laws issued by the
local government.
iii
警告：電池若未妥善處理，可能會導致爆炸。
請勿拆卸電池，或用火銷毀電池。請將電池放置於兒童拿不到的地方。
請使用專用充電器充電，並請依照當地政府或法律規定妥善處理廢棄
電池。
低功率電波無線輻射電機管理辦法
第十二條：經型式認證合格之低功率射頻電機,非經許可,公司,商
號或使用者均不得擅自變更頻率,加大功率或變更原設計之特性
及功能。
第十四條：低功率射頻電機之使用不得影響飛航影響安全及干擾
合法通信,經發現有干擾現象時,應立即停用,並改善至無干擾時方
得繼續使用。
前項合法通信,指一電信法規定作業之無線電通信低功率射頻電
機需忍受合法通信或工業,科學及醫療用電波輻射性電機設備之
干擾
本產品支援 WIFI/Bluetooth/Sub-1G(依不同型號有所不同)
製造商：立象科技股份有限公司
地址：新北市新店區寶橋路 235 巷 126 號 7 樓
電話：02‐8912‐1121（代表號）
iv
v
Release Note
Release Note
Version Date
Note
V1.0
02/22 2017
Initial release
V1.1
07/12 2017
Add Appendix A for reference
V1.1
02/13 2018
Add Appendix B for reference
V1.2
06/05 2018
Add PI-1060, Tag-60 information
Content
1 Introduction .......................................................................... 1
1.1 Unpacking ................................................................. 2
1.2 Understand your terminal ........................................ 4
1.2.1 Terminal ........................................................ 4
1.2.2 Holder(Option) .............................................. 5
1.3 Indicators .................................................................. 6
1.3.1 LED ................................................................ 6
1.3.2 Buzzer............................................................ 8
1.3.3 Vibration ....................................................... 8
1.4 Keypad ...................................................................... 9
1.5 Power source .......................................................... 15
1.6 Tag‐60 introduction (PI‐1060 only) ......................... 16
2 Get started .......................................................................... 17
2.1 Set up your terminal ............................................... 21
2.2 User interface ......................................................... 23
2.3 Connection ............................................................. 25
2.3.1 Remote link connection .............................. 26
2.4 Attach the hand strap ............................................. 30
2.5 Tag‐60 (PI‐1060) ...................................................... 32
3 Controls and settings .......................................................... 35
3.1 User Menu .............................................................. 35
3.1.1 Run Program ............................................... 36
3.1.2 Remote Link ................................................ 36
3.1.3 Scanner(HID) ............................................... 37
ii
3.1.4 Information ................................................. 38
3.2 System Menu .......................................................... 39
3.2.1 Remote Link ................................................ 39
3.2.2 Disk info ...................................................... 39
3.2.3 Timer setting............................................... 40
3.2.4 Environment ............................................... 41
3.2.5 Test .............................................................. 42
3.2.6 System info.................................................. 44
3.3 Supervisor Menu .................................................... 45
3.3.1 Remote Link ................................................ 46
3.3.2 Format disk ................................................. 49
3.3.3 Setting ......................................................... 50
3.3.4 Information ................................................. 55
4 Applications ........................................................................ 56
5 Troubleshooting.................................................................. 57
5.1 Hardware issues...................................................... 57
5.2 Communication issues ............................................ 58
5.3 Barcode scanning issues ......................................... 59
6 Specifications...................................................................... 60
Appendix A .............................................................................. 66
Appendix B .............................................................................. 83
iii
1 Introduction
Unpacking
1 Introduction
PI series is a lightweight, portable data terminal (PDT)
for data capture and collection. This manual will help
you to get to know PI series and utilize it well.
Features
￭ Scratch‐resistant keypad Coated with PC
(polycarbonate), the letters and numbers on the keys
won’t wear off between uses.
￭ Battery cover open detection When the switch of
the battery cover is up, the system automatically
saves your files and shut down.
￭ Large flash memory
PI series offers more flash
memory than the rivals on the same level. The
standard is 20 MB, and the optional is 60 MB.
￭ Backup battery The backup battery gives you
additional 15 minutes to finish your job if the primary
batteries wear out.
￭ Wi‐Fi connectivity You can exchange data over a
Wi‐Fi network.(PI‐1030)
￭ Tag‐60
1 Introduction
Unpacking
1.1 Unpacking
Make sure all of the following items are included in your
package.
PI series
Quick Start Guide
USB Cable
or
Holder
RS‐232 Cable with USB
power cord
Hand Strap
1 Introduction
Unpacking
Plug and Power Supply (Option)
Tag‐60 (PI‐1060)
When you receive your terminal, open the package
immediately and inspect for shipping damage. If you discover
any damage, contact the shipping company and file a claim.
Argox is not responsible for any damage incurred during
shipping. Save all package materials for the shipping company
to inspect.
Note If any item is missing, please contact your
local dealer.
1 Introduction
Understand your terminal
1.2 Understand your terminal
1.2.1 Terminal
Left
Front
Right
Back
Top
Bottom
LED
Three LEDs.
LCD Display
A mono LCD.
Keypad
A 25‐key keypad.
Battery Cover
The battery cover.
Battery Cover Switch
Open and close the battery cover.
Reading Window
The bar code reading beam is emitted
through this window.
Speaker
Buzzer sound
1 Introduction
Connector
Understand your terminal
A port to connect computer
1.2.2 Holder
The holder is used to hold your terminal in its standing
position.
In the bottom of holder, make sure cable wire is
installed as below.
1 Introduction
Indicators
1.3 Indicators
PI series has three LEDs and a buzzer to indicate its current
status.
1.3.1 LED
Your terminal has three LEDs on the upper‐left corner.
They have different behavior. The table below gives
information about the status they indicate.
BT or Wi‐Fi LED
Scan LED
Charger LED
LED
Scan LED
Color
Green, Red and Orange
BT or Wi‐Fi LED
Blue
Charger LED
Red
1 Introduction
LED
Scan
LED
BT &
Wi‐Fi
LED
Indicators
Behavior
Solid green
Status
User defined
Note
Use SDK.
Solid red
User defined.
Use SDK.
Solid orange User defined.
Use SDK.
Flashing
green
Transmitting data or
user defined.
Use SDK.
Flashing red
User defined.
Use SDK.
Flashing
orange
User defined.
Use SDK.
Off
No data transmission
or user defined.
Use SDK.
Solid blue
Your terminal is
connected through
Bluetooth or Wi‐Fi.
Flashing
blue
Your terminal is ready
to be connected
through Bluetooth or
Wi‐Fi.
Off
Bluetooth or Wi‐Fi is
turned off.
Default
Your terminal is fully
charged or connected
to a power source.
Controlled
by
hardware.
Charging.
Controlled
by
Charger Solid red
LED
Flashing red
1 Introduction
LED
Indicators
Behavior
Status
Note
hardware.
Off
Your terminal is not
connected to any
power source.
Controlled
by
hardware.
1.3.2 Buzzer
You can define the status the vibration indicates using
the SDK.
Sound
1 Short Beep
Status
A key is pressed.
A good scan.
An error occurred.
2 Short Beep
The battery is low.
4 Short Beep
Battery is too low to turn off
terminal.
1.3.3 Vibration
You can define the status the vibration indicates using
the SDK.
Vibration
Vibrate
Status
A good scan.
1 Introduction
Keypad
1.4 Keypad
Scan key
Cursor keys
Control keys
Numeric keys
User‐defined keys
Power key
Scan key
Scan a bar code.
Cursor keys
Up
Move the highlight bar up.
Fn+Up
Open Message Menu.
Down
Move the highlight bar down.
Fn+Down
Adjust the backlight brightness. The
brightness repeats the sequence
0123.
Left
Move the highlight bar to the top.
Fn+Left
Reduce the volume.
Right
Move the highlight bar to the bottom
1 Introduction
Keypad
Cursor keys
Fn+Right
Increase the volume.
Control keys
ESC The Escape
key.
1. Go up one level in a menu.
2. Give up changing a setting.
3. Exit a program.
Fn
The Function
key.
Use with other keys. Ex:
“Fn+Down Arrow” is to adjust
the backlight brightness. The
function of F0 ‐ F9 (Fn+0 ‐ 9)
can be defined using an SDK.
ENT
The Enter key.
1. Enter a menu.
2. Select an option.
BS
The Backspace
key.
1. Delete a character to the
left of the cursor.
Numeric keys
You can use the keypad to enter numbers or English
characters, depending on the mode you’re using.
1. Enter the number one.
2. Enter these signs: plus (+), minus (‐), star
(*) and slash (/).
1. Enter the number two.
2. Enter the letters A, B, C.
10
1 Introduction
Keypad
Numeric keys
1. Enter the number three.
2. Enter the letters D, E, F.
1. Enter the number four.
2. Enter the letters G, H, I.
1. Enter the number five.
2. Enter the letters J, K, L.
1. Enter the number six.
2. Enter the letters M, N, O.
1. Enter the number seven.
2. Enter the letters P, Q, R, S.
1. Enter the number eight.
2. Enter the letters T, U, V.
1. Enter the number nine.
2. Enter the letters W, X, Y, Z.
1. Enter the number zero.
2. Enter these characters: space ( ), at (@),
comma (,) and semicolon (;).
Alpha Switch the input method between numbers,
uppercase and lowercase characters.
1. Enter a period (.).
2. Enter these symbols: dollar sign ($),
percent sign (%), ampersand (&) and
number sign (#).
11
1 Introduction
Keypad
User‐defined keys
P1
User‐defined key.
P2
User‐defined key.
P3
User‐defined key.
Power key
Turn on or turn off your terminal.
Power combination key
You can use the key combinations to enter different
menus or modes. Press and hold the combination of
keys, until your terminal responds.
3 + 9 + Power
System Menu.
1 + 3 + 0 + Power
Supervisor Menu.
1 + 3 + Power
Force mode.
P1 + P2 + P3 + Power
BIOS reset.
SCAN + Power
Warm reset.
SCAN + Power (5 sec)
Cold reset. You need to press
the keys for 5 seconds.
12
1 Introduction
Keypad
￭ System Menu Enter System Menu.
￭ Supervisor Menu Enter Supervisor Menu.
￭ Force mode It updates all firmware files and
restores all system parameters to factory settings.
This mode needs to be used with an SDK or computer
software. You can use this mode when you encounter
the problem that can’t be resolved in any other way.
￭ BIOS reset it is the same as BIOS default (see
Supervisor Menu). It resets all your terminal settings,
including the password of Supervisor Menu.
￭ Warm reset It restarts your terminal without
changing any settings. You can use it when your
program stops responding.
￭ Cold reset
It forces your terminal to restart. The
data stored in the DRAM may be removed. You can
use it when your terminal crashes, or when you can’t
turn on your terminal by pressing the Power key.
13
1 Introduction
Keypad
14
1 Introduction
Power source
1.5 Power source
There are three ways to supply power to PI series:
1. Two AA batteries. Recommended alkaline
rechargeable type.
2. Use the USB cable with computer.
3. Use the power supply with the USB or RS‐232
cable.
Cable Type
USB
Charge
your
batteries
Yes
Supply power
without
batteries
Yes
Need to use
with a power
supply
No
RS‐232
No
No
Yes
Note It’s not necessary to use a USB cable with the
power supply, but the battery charging time is
shorter with it.
15
1 Introduction
Tag‐60 introduction (PI‐1060 only)
1.6 Tag‐60 introduction
(PI‐1060 only)
TAG‐60 ID No.
Blue LED
Top strap hole
Battery
Buzzer
Red LED
Latch
You can define indicator function by using SDK or Skywalker.
LED Color
Blue
Status
Tag‐60 is called.
Red
Tag‐60 battery low warning
Sound
Beep
Status
Beep is defined by PI‐1060
application.
16
2 Get started
Tag‐60 introduction (PI‐1060 only)
2 Get started
This chapter provides information about how to work
with your terminal and make connection to computer.
Inserting or replacing battery
When you see the battery icon shows low. You need to
change new battery or charge it immediately. If there is
no power, the back up battery can hold the data about
15 minutes. Therefore, always upload your important
data after work or keep two AA batteries in case.
Caution Do not mix old batteries and new batteries or
standard (carbon‐zinc) with alkaline batteries. Remove
batteries if product is not to be used with for a long time. Risk
of explosion if battery is replaced by an incorrect type.
Dispose of used batteries according to the instructions.
DO NOT RECHARGE DIFFERENT TYPES OF BATTERIES.
17
2 Get started
Tag‐60 introduction (PI‐1060 only)
1. Press and slide two release latches at the same time
to open the battery cover.
2. Inserting two batteries as indicated inside battery
compartment.
‐
‐
18
2 Get started
Tag‐60 introduction (PI‐1060 only)
3. Close the battery cover as follow.
②
①
4. Make sure cover is closed and slide two latches
back.
19
2 Get started
Tag‐60 introduction (PI‐1060 only)
Charge the battery
If you’re using rechargeable batteries to supply power
to your terminal, you can charge them by
(1)connecting the USB cable to your terminal and
computer.
(2)Using a battery charger to charge batteries in
advance.
(3)Connecting the USB cable to your terminal and use
a power supply.
When your batteries are fully charged, the Charger LED
turns to solid red.
Charging by
Full Charge Time
Power Supply
5‐6 hours
USB Cable
7‐8 hours
Important Before using PI series, we
recommend to charge PI‐1000 series 1 day to
make sure backup battery is fully charged.
Important To protect power source, PI series
can not be powered on unless battery cover
back are closed correctly.
20
2 Get started
Set up your terminal
Note
The triangle mark should be face up when
you want to connect to PI series.
2.1 Set up your terminal
1. Choose one to power on your terminal

Open the battery cover and Install two AA
21
2 Get started
Set up your terminal
batteries.

Connect your terminal to your computer using
USB or RS‐232 cable.
2. Press the Power key to turn on your terminal.
Power key
22
2 Get started
User interface
2.2 User interface
Menu
Options
Status bar
Input
method
Power
source
Time
Wireless
Item
Menu
Description
Current menu title
Options
Items in the menu.
Status bar
It displays the information about your
terminal.
Input method
The way you enter data. You can enter
numbers, lowercase or uppercase
characters.
Time
The current time.
23
2 Get started
User interface
Item
Wireless
communication
Description
When you open Bluetooth or Wi‐Fi
function, it displays an icon without
waves. If connection is successful, the
icon will show waves.
Power source
If your terminal is connected to a direct
power supply (USB or RS‐232), it displays
a plug icon; if it is running on batteries, it
displays a battery icon.
24
2 Get started
Connection
2.3 Connection
PI series have four interfaces to connect: USB, RS232,
Bluetooth and WI‐FI. Each one can choose two ways as
below.
Remote link: It is a unique protocol from Argox
development. Visit Argox website below to download
application.
http://www.argox.com/content2011.php?sno=0000033
Linking port: Developer can set up different
interfaces USB/WIFI/COM/BT according to their
application.
Important
Remote link has to use Argox
application, such as PhoenixVoler or Everlink
from Argox.
25
2 Get started
Connection
2.3.1 Remote link connection
This section will show how to link PI series to PC with
“Remote link” and enter “Message menu” to send
message when the connection successful.
Use Remote link to connect PC with USB
Step 1. After link USB cable between PI series and PC,
press “Power” key to power on PI series.
Step 2. Move curse to “Remote Link” and press “ENT”
key.
26
2 Get started
Connection
Step 3. Enter “Remote I/F Select” and Choose “USB”.
It will get return last page when press”Enter”
Step 4. Choose “Connect”.
Step 5. In PhoenixVoler or Everlink, Click Comm setup
will show the model number. Successfully
connected to PC.
27
2 Get started
Connection
Message Menu
Everlink, ControlCenter and PI series can send
message to PI series. Press “Fn”+”^” key to enter
Message Menu.

Read priority Msg.: It shows the priority
message you receive.

Read Msg.: It shows the message you sent.

Send Msg.:

To Everlink: “Send to” is 9000

To ControlCenter: “Send to” is 9001

To otherPI series device: “Send to” default
depends on SN last four digits. To change
ID, refer to “Equipment ID” in System
menu.
Important
Sending message rely on Everlink. PI
28
2 Get started
Connection
series must connect to Everlink then the message will
start to send and receive.
29
2 Get started
Attach the hand strap
2.4 Attach the hand strap
Sometimes you may need to do something and can’t
hold your terminal on your hand. Or, you might
accidentally drop your terminal between uses. Attach
the hand strap is a useful way to resolve these issues.
You can wrap the strap around your hand to secure it to
your hand, or hang it on your hand to have both hands
free to do other things.
To attach the hand strap, do this:
1. Pinch the small loop and thread it into the two
square holes under the battery cover.
30
2 Get started
Attach the hand strap
2. Thread the big loop into the small loop, and pull the
big loop to tie a knot.
Important Use hand strap when you collect
barcode in case drop accident. PI series might shut
down to protect data after drop.
31
2 Get started
Tag‐60 (PI‐1060)
2.5 Tag‐60 (PI‐1060)
Start Tag‐60 up
1.
Hold Tag‐60 bottom, press latch to remove cover.
2.
Remove battery insulation to start Tag‐60 up.
3.
Make sure battery is in the slot and close cover back.
32
2 Get started
Tag‐60 (PI‐1060)
Insert or replacing Battery
1.
Hold Tag‐60 bottom cover, press latch to remove cover.
2.
Replace CR‐2032 coin battery. Make sure positive
electrode is up.
3.
Make sure battery is in the slot and close cover back.
Top Strap hole
33
2 Get started
Tag‐60 (PI‐1060)
Top case is designed 3 holes for placing Tag‐60 easily. Attach a
strap on Tag‐60 can hanging it everywhere and also prevent
drop damage.
34
3 Controls and settings
User Menu
3 Controls and settings
PI series offers three different layer menus. User Menu
is for general users, System Menu is for supervisors or
managers, and Supervisor Menu is for system
administrators or engineers. Besides, press Fn+^ can
enter Message Menu This chapter provides information
about these menus.
3.1 User Menu
User Menu includes three frequently used settings. You
can use them to run your program, connect your
terminal to a computer or other device, or display your
terminal’s information (via Everlink).
35
3 Controls and settings
User Menu
3.1.1 Run Program
It shows the program you download from your
computer. To run a program, just select it and press ENT.
If there’s no program, it will tell you “No program file.”
For more information about how to connect to a
computer and download programs from it, see
PhoenixVoler or Everlink User guide.
Note Default setting between PI Series and Program
is individual
3.1.2 Remote Link
It is for you to connect your terminal with Everlink or
36
3 Controls and settings
User Menu
PhoenixVoler to computer.
￭ Connect It connects your terminal to computer
after you select an interface.
￭ Remote I/F Select It provides interfaces, including
COM port, USB, Bluetooth and WI‐FI.
To connect your terminal, do this:
1. Select Remote Link > Remote I/F Select > COM
port/USB/Bluetooth/WI‐FI.
2. Go up one level in the menu and select Connect.
Note If you want to connect via Bluetooth or WI‐FI,
you need to enter Supervisor Menu and set up
Bluetooth connection or WI‐FI connection first. After
completing the setting, you can connect your
terminal from User Menu Connect.
3.1.3 Scanner(HID)
37
3 Controls and settings
User Menu
It is for you to read and upload barcode data easily.
Once you have connection to computer. Press “SCAN”
key to read barcode and it will upload data. Go to CH 4
Application. see more in Everlink user guide.
Note Make sure you turn on the decode
function(barcode default).
3.1.4 Information
It displays your terminal’s information.
IPL
BOOT
Kernal
Scanner
SN
DefLang
The IPL version.
The boot version.
The kernel version.
The scanner’s firmware version.
The serial number.
The display language.
38
3 Controls and settings
System Menu
3.2 System Menu
Under System Menu, you can change system settings to
meet your need and run some tests to see if your
terminal is working properly. Press key 3 + 9 + Power to
enter system menu.
3.2.1 Remote Link
See the description in Remote Link in User Menu.
3.2.2 Disk info
39
3 Controls and settings
System Menu
It provides the disk information, including the free,
used and total disk space. By default, your terminal has
two disks: C and D.
RAM
For data memory
Flash For system and user’s application
3.2.3 Timer setting
￭ Set date & time
You can set date and time here.
￭ Set time format You can set the time format here. It
provides the 12‐hour or 24‐hour clock and only
display in Status Bar.
40
3 Controls and settings
System Menu
3.2.4 Environment
It provides settings for you to adjust different
workplace or match your preference.
￭ LCD contrast It determines the contrast ratio. The
bigger the number, the lower the contrast (the darker
the screen).1~10
￭ Backlight timer It determines how long the
backlight stays on after you press a key.1~65535. Set 0
will always on.
￭ Auto off timer It turns off your terminal after a
certain amount of time elapsed. The unit of time is
the second. If you set it 0, your terminal is always
turned on.30~65535
￭ Always on if DC in It will always on when you plug
DC power. Default is disable.
41
3 Controls and settings
System Menu
￭ Key click You can turn on or turn off the sound of
keypad.
￭ Vibration It determines how long your terminal
vibrates. The unit is 0.1 second, range is 1~255. Set 0
will turn it off.
3.2.5 Test
It provides various tests for you to check your terminal
system.
￭ Memory test It checks if the memory can be written
and read properly. Note that this test removes all data
stored in the memory, so remember to save your files
in advance.
￭ Buzzer test It checks if the buzzer can make sound
properly. You’ll hear the sound repeatedly plays from
42
3 Controls and settings
System Menu
high to low and from low to high. If the sound is
played smoothly, it means the buzzer works properly,
otherwise the buzzer may have some issues.
￭ LCD & LED test It checks if the LCD display has bad
pixels.
￭ Keypad test It checks if the keypad works properly
when you press it.
￭ Linking port test It checks if the port works properly.
You need to set a port to run this test. For more
information about the port setting, see the
description in Setting in Supervisor Menu.
After you set a port, do this:
1. Select the port you want to test, and press ENT.
2. Your terminal will show if the test is successful or
failed after the test is complete.
￭ Scanner test It checks if your terminal can read bar
codes when you press SCAN to scan bar codes. If the
scan is successful, your terminal will vibrate and
display the bar code data.
Note When you do scanner test to barcode,
turn on the function in Barcode config
(Supervisor Menu).
43
3 Controls and settings
System Menu
3.2.6 System info
See the description in Information in User Menu.
44
3 Controls and settings
Supervisor Menu
3.3 Supervisor Menu
(1+3+0+PWR)Supervisor Menu provides advanced
settings for you to configure. To protect the settings
from being changed easily, you need to enter a
password to access the menu. By default, the password
is five zeros (00000).
45
3 Controls and settings
Supervisor Menu
3.3.1 Remote Link
It is for you to connect your terminal with Everlink or
PhoenixVoler to computer.
￭ Connect It connects your terminal to computer
after you select an interface.
￭ Remote I/F Select It provides interfaces, including
COM port, Bluetooth and WI‐FI.
￭ Remote I/F Set It has three options:
∙ COM port You can select a baud here.
46
3 Controls and settings
Supervisor Menu
∙ Bluetooth It has three options:
1. Bluetooth setting:
(1) Device name: Your terminal’s name. By
default, the name is the serial number.
(2) PIN code: The passkey for a Bluetooth
connection. By default, the code is four
zeros (0000).
(3) Security mode: It has two options.
a. Security: Your terminal will ask other
devices to enter a PIN code when they
try to connect to your terminal.
b. Encryption: It encrypts the connection to
prevent data theft.
(4) Inquiry timeout: It determines how long
your terminal stops searching other devices
after a certain amount of time elapses.
(5) Max response: It determines the maximum
number of connectable devices your
terminal lists.
(6) Set peer device: It has two options.
a. Set by search: Search other devices in the
neighborhood.
b. Set by keyin: Search another device by
47
3 Controls and settings
Supervisor Menu
entering its Bluetooth MAC address.
2. Bluetooth test: You can use this option to test
the Bluetooth connection after your terminal
connects to a device.
3. Bluetooth info: It displays Bluetooth
information, including the local address, device
name and link address.
∙ WI‐FI It has three options
1. Setting
(1) WI‐FI SSID:
a. Set by search: Search WI‐FI signal in the
neighborhood.
b. Set by keyin: Type New SSID to connect
the WI‐FI you prefer.
(2) Network: It is the same as computer
network. The Default is “Enable” DHCP to
auto get IP Address, Subnet Mask and
Gateway. Or you can “Disable” DHCP to set
your WI‐FI data.
(3) Connect setting: Type “New IP” and “New
Port” to get connection.
(4) System Scale: There are 3 Level to choose.
The default is “High”
48
3 Controls and settings
Supervisor Menu
(5) Power Saving: If Disable, WI‐FI module will
always awake to transmit data. Otherwise,
WI‐FI will automatically turn off.
2. TCP Test: Test WI‐FI connection, the process
need to wait about 3~15 seconds. PI series will
show the connect success of fail on the screen.
3. Information: It displays WI‐FI information.
(1) Remote port: show the page is under
remote port.
(2) MAC: Show MAC address after you connect.
(3) DHCP: The status is Enable or Disable.
(4) rIP: Current remote IP Address.
(5) rPort: Current remote Port.
3.3.2 Format disk
49
3 Controls and settings
Supervisor Menu
It formats a disk in your terminal. The system will ask
you to confirm if you want to format, because it will
remove all data stored in the disk.
￭ Format C Format the C disk.
￭ Format D Format the D disk.
3.3.3 Setting
It offers a variety of settings that you can change to
meet your need.
￭ Equipment ID Your terminal’s ID. The default ID is
four zeros (0000). You can replace it with a new ID.
The ID needs to be a 4‐digit number.
￭ BIOS Password It is the password of Supervisor
Menu. The password needs to be a 5‐digit number.
￭ BIOS default It resets all your terminal settings,
including the password of Supervisor Menu.
50
3 Controls and settings
Supervisor Menu
￭ Environment It provides settings for you to adjust to
adapt to different workplaces or match your
preference. For the first five options, see the
description in Environment in System Menu.
∙
Power on It determines the screen displayed
in User Menu after you turn on your terminal.
1. Resume: The system displays the last screen you
visited in User Menu every time you turn on
your terminal.
2. Reset: The system displays the default screen in
User Menu every time you turn on your
terminal.
∙
Status bar You can choose if you want to
display the status bar.
￭ Scanner It provides several settings for the scanning
functionality.
∙
Reading test See the description in Test in
System Menu.
∙
Indication It has two options:
1. LED: You can turn on or turn off the LED.
2. Beep: You can turn on or turn off beeps.
∙
Code ID Code ID is an identifier for a bar code.
It has two options:
51
3 Controls and settings
Supervisor Menu
1. Transmission: It has two modes: Proprietary
ID or AIM ID. You can choose either of them.
Proprietary ID is defined by Argox. AIM ID is
defined by the AIM organization.
2. Position: You can insert the code ID before
or after the bar code data.
∙ Invert Image When you turn on this feature, you
can scan both regular and inverted bar codes.
∙ Preamble Add a character or characters before a
bar code.
∙ Postamble Add a character or characters after a bar
code.
∙ Barcode config It provides several settings for each
bar code type. Change them to meet your need.
The list below shows the bar code types system
default setting.
Bar Code Type
1. Code‐11
2. Code‐39
3. Code‐93
4. Code‐128
5. EAN‐8
6. EAN‐13
7. UPC‐A
ON
OFF
○
○
○
○
○
○
○
52
3 Controls and settings
Supervisor Menu
8. UPC‐E
9. Industrial 25
10. Interleaved 25
11. Standard 25
12. MSI‐Plessey
13. UK‐Plessey
14. RSS 14
15. RSS Limited
16. RSS Expanded
17. CODABAR
18. Telepen
19. Matrix 2 of 5
20. China Post
21. Pharmacode
○
○
○
○
○
○
○
○
○
○
○
○
○
○
￭ Language You can change the language for the
system to display items in the user interface. It has
two options: English, TC (Traditional Chinese) and
SC(Simple Chinese).
￭ Linking port You can decide which port you want to
use and configure its settings. To set a port, do this:
1. In Port IF select, select a port and its interface.
2. In Port IF setup, select the port you choose in the
previous step, and configure the settings of its
53
3 Controls and settings
Supervisor Menu
interface.
∙
Port IF select It has four ports. Select one of
them and choose its interface. You can choose
COM, USB, Bluetooth and WI‐FI. If you don’t
want to use interface, choose None.
∙
Port IF setup It provides the settings of COM,
Bluetooth and WI‐FI. For more information
about the settings, see Remote Link in
Supervisor Menu.
∙
Port info It displays the port information.
Press Up Arrow and Down Arrow to check
different ports.
Important
Linking port is for development
usage and transmit raw data. See more
information, go to CH 2.3 Connection
￭ Freq. set (PI‐1060 Only) Change PI‐1060 Frequency
setting to trigger Tag‐60
∙
868 Set PI‐1060 to RF 868 MHz frequency
which is for Europe communication.
∙
920 Set PI‐1060 to RF 920 MHz frequency
which is for non Europe communication.
54
3 Controls and settings
Supervisor Menu
3.3.4 Information
It displays your terminal’s information.
IPL
The IPL version.
BOOT
The boot version.
Kernal
The kernel version.
Scanner
The scanner’s firmware version.
SN
The serial number.
HW Ver.
The PCBA (Printed Circuit Board
Assembly) version.
HW Int.
The hardware version.
DefLang
The display language.
55
4 Applications
Supervisor Menu
4 Applications
Argox provides multiple applications for communication and
developments as below:
Communication
PhoenixVoler
Upload and Download firmware or
application easily. Recommend developer.
Everlink
Manage multiple PI series with files
transmission, message sending and history
data function.
Control center Remote‐end of manage program can link
multiple Everlink and provide Cloud
operation.
Development application
Skywalker
User friendly software development kit
Go to Argox website to get more applications and user
guide
http://www.argox.com/content2011.php?sno=0000033
Note PI Series accept “.bas” and “.bin” file from
Basic and C compiler.
56
5 Troubleshooting
Hardware issues
5 Troubleshooting
5.1 Hardware issues
Speaker is not working or volume is too low.
￭ Make sure the speaker hole is not blocked.
￭ Test is in the system menu, use Test to check speaker.
Keypad does not response.
￭ Test is in the system menu, use Test to check keypad.
￭ The system might be crush. Use Scan + Power key to
warm reset or cold reset (hold 5 seconds).
My terminal keeps turning itself off or can not open.
￭ If you’re using batteries, check them and see if they
need to be charged.
￭ If your terminal is connected using USB or RS‐232
cable, make sure the cable is tightly plugged.
￭ The duration of Auto off Timer is too short. Set it a
longer duration from Auto off timer in Environment
57
5 Troubleshooting
Communication issues
5.2 Communication issues
Receive or transmit problem on USB
￭ Check USB connector is plugged correctly.
￭ Check Remote Link set is USB and select the right PI
series name on computer.
￭ Restart PI series and unplug the USB and try again.
Receive or transmit problem on RS‐232
￭ Check RS‐232 connector is plugged correctly.
￭ Check Remote Link set is COM port and select the
same port on computer.
￭ Restart PI series and unplug the RS‐232 and try again.
Receive or transmit problem on Bluetooth
￭ Check Remote Link set is Bluetooth port and
Bluetooth setting is correct.
￭ Be sure PI series is in the Bluetooth range
58
5 Troubleshooting
Barcode scanning issues
5.3 Barcode scanning issues
Barcode can not be read
￭ Change the angle between the bar code and the
terminal.
￭ Change the distance between the bar code and the
terminal.
￭ Clean the scanning window slightly of the
terminal(make sure without scratch).
￭ Enabled the bar code symbology in supervisor menu >
3.Setting > 5.Scanner > 7.Barcode config.
59
Specifications
6 Specifications
General Characteristics
OS
Argox Proprietary
CPU
ARM926EJ‐S
RAM
16 / 32 MB DRAM
ROM
20 / 60 MB Flash
Display
White gray mono STN LCD 160*160
Indicator
LED Blue, Green and Red; Beeper;
Vibration Motor
Keypad
25 Alpha‐Numeric keys (Including 10
function keys, 3 programmable hot
keys)
Accessory
Holder (Standard), Power Supply
Dimensions
145.0mm (L) x 55.0mm (W) x 26.0mm
(H)
Weight
230g with battery
60
Specifications
Model
PI‐1010
WPAN
PI‐1030
PI‐1060
PI‐1230
Bluetooth Class2, BT2.1+EDR
WLAN
N/A
Wi‐Fi
802.11b/g
/n
N/A
RF
N/A
N/A
+15dbm max. N/A
( Max output
power)
I/O
Interface
USB 2.0 / RS‐232
61
Wi‐Fi
802.11b/g
/n
Specifications
Scanner
Model
PI‐1010/PI‐1030/PI‐1060
PI‐1230
Scanner
system
CCD
2D Area imager
Resolution
3 mil at PCS 90%
1D(5 mils):Code 39
2D(6.7miks):
PDF417
Depth of
field
3mil
Code39
5mil
40‐90
mm
Code39
5mil
45‐140
mm
EAN 13
13mil
20mi 65‐570
mm
EAN 13
13m
il
Datamatrix 15mil
55‐435
mm
Scanning
rate
200 scan/sec
Decode
capability
Code‐11、Code‐39、
Code‐93、Code‐128、
EAN‐8、EAN‐13、UPC‐A、
UPC‐E、Industrial 25、
Interleaved 25、Standard
25、MSI‐Plessey、
UK‐Plessey、RSS 14、RSS
Limited、RSS Expanded、
62
Auto discriminates
all standard
one‐dimension
barcodes; including
GS1 databar
PDF417, MicroPDF,
Composite
Codes(CC‐A, CC‐B,
Specifications
CODABAR、Telepen、
Matrix 2 of 5、China
Post、Pharmacode
Expansion
Storage
CC‐C)
OCR‐A,
OCR‐B,OCR‐C, Aztec
(Standard, Inverse),
MaxiCode,
DataMatrix/ECC 200
(Standard, Inverse),
QR Code , Micro QR
Micro SD (up to 16 GB)(factory option)
Developing Tools
Software
Software Development Kit (SDK),
Skywalker (Proprietary application
software generator)
Programming C language, BASIC language
Language
Power
Battery
AA size NIMH Battery *2 (charged by USB
or optional power adapter) or AA size
Alkaline *2
( Recommend AA size NIMH Battery for
daily work)
63
Specifications
Power
Rating
5Vdc
2A
Physical and Environment
‐10℃ ~ 60℃ / 14F ~ 140F
Operating
Temperature
Storage
Temperature
‐20℃ ~ 70℃ / ‐4F ~ 158F
Humidity
1) Operating: Non‐condensed 10 ~ 90%
2) Storage: Non‐condensed 5 ~ 95%
Impact
Resistance
1) Terminal 1.2M/4ft
2) IP54
Electrostatic
Discharge
1) +/‐ 15 KV air discharge
direct discharge
EMC
Regulation
FCC, CE, BIS, BSMI
64
2) +/‐ 8 KV
Specifications
Model
Light
indication
TAG‐60
Blue LED
Sound alert
Buzzer >80dbA @ 10cm, programmable
sound pattern
Beeping
pattern
Programmable beeping pattern
RF Sensitivity ‐110 dbm typ.
Frequency
bands (TBD)
410~475, 820~950 MHz
Power
CR‐2032 coin battery, 1 years standby
minimum
Drop
1.5M
Dimensions
76.0mm (L) x 50.0mm (W) x 17.0mm (H)
65
Appendix A
Appendix A
Scan Module (CCD) Configuration Table
Default (*)
Command1
Command2
LED indication
Indication
Option/Limitation
Disable
Enable *
Buzzer indication
Disable
Enable *
Preamble transmission
Disable *
Enable
Postamble
Disable *
transmission
Enable
Code ID position
Before code data *
After code data
Transmission
Code ID transmission
Disable *
Proprietary ID
AIM ID
Code length
Disable *
transmission
Enable
Code name
Disable *
transmission
Enable
Disable *
66
Appendix A
Case conversion
Upper case
Lower case
0~9
Scan
Double confirm
0*
0 ~ 99
Global min. code
4*
length
0 ~ 99
Global max. code
63 *
length
Disable *
Inverted image scan
Enable
0*
String setting
Prefix characters
0x00 ~ 0xff ASCII code
setting
12 characters.
0*
Suffix characters
0x00 ~ 0xff ASCII code
setting
12 characters.
0*
Preamble characters
0x00 ~ 0xff ASCII code
settings
12 characters.
0*
Postamble characters
0x00 ~ 0xff ASCII code
settings
12 characters.
Disable *
Code 11
Read
Enable
67
Appendix A
Disable/Disable
Check-sum transmit
Disable/One digit *
/verify
Disable/Two digits
Enable/One digit
Enable/Two digits
0 ~ 64
Max. code length
0*
0 ~ 64
Min. code length
0*
0 ~ 15
Truncate leading
0*
0 ~ 15
Truncate ending
0*

Code ID setting
0x00 ~ 0xff ASCII
code(1 or 2 bytes)
Code 39
Read
Disable
Enable *
Check-sum transmit
/verify
Disable/Disable *
Disable/Enable
Enable /Enable
Max. code length
0 ~ 64
0*
Min. code length
68
0 ~ 64
Appendix A
1*
Truncate leading
0 ~ 20
0*
Truncate ending
0 ~ 15
0*
<*>
Code ID setting
0x00 ~ 0xff ASCII
code(1 or 2 bytes)
Standard *
Format
Full ASCII
Disable *
Start/stop transmission
Enable
Disable *
Code 93
Read
Enable
Disable/Disable
Check-sum transmit
Disable/Enable *
/verify
Enable /Enable
0 ~ 64
Max. code length
0*
0 ~ 64
Min. code length
0*
0 ~ 15
Truncate leading
0*
0 ~ 15
Truncate ending
69
0*
Appendix A
<&>
Code ID setting
0x00 ~ 0xff ASCII
code(1 or 2 bytes)
Disable
Code 128
Read
Enable *
Disable/Disable
Check-sum transmit
Disable/Enable *
/verify
Enable /Enable
0 ~ 64
Max. code length
0*
0 ~ 64
Min. code length
1*
0 ~ 15
Truncate leading
0*
0 ~ 15
Truncate ending
0*
<#>
Code ID setting
0x00 ~ 0xff ASCII
code(1 or 2 bytes)
Standard *
Format
UCC.EAN 128
<#>
UCC/EAN 128 ID
0x00 ~ 0xff ASCII
setting
code(1 bytes)
0x1D *
70
Appendix A
Concatenation code
0x00 ~ 0xff ASCII
code(1 bytes)
Codabar
Disable *
Read
Enable
Disable/Disable *
Check-sum transmit
Disable/Enable
/verify
Enable /Enable
0 ~ 64
Max. code length
0*
0 ~ 64
Min. code length
0*
0 ~ 15
Truncate leading
0*
0 ~ 15
Truncate ending
0*
<%>
Code ID setting
0x00 ~ 0xff ASCII
code(1 or 2 bytes)
ABCD/ABCD *
Start/stop type
abcd/abcd
ABCD/TN*E
abcd/tn*e
Disable *
Start/stop transmission
Enable
Disable
71
Appendix A
EAN 8
Read
Enable *
Disable
Check-sum
Enable *
transmission
0 ~ 15
Truncate leading
0*
0 ~ 15
Truncate ending
0*

Code ID setting
0x00 ~ 0xff ASCII
code(1 or 2 bytes)
None *
Supplement digits
2 digits
5 digits
2, 5 digits
UCC/EAN 128
2, UCC/EAN 128
5, UCC/EAN 128
All
None *
Truncation/expansion
Truncate leading zero
Expand to EAN 13
Disable *
Expansion
Enable
Disable
EAN 13
Read
Enable *
72
Appendix A
Disable
Check-sum
Enable *
transmission
0 ~ 15
Truncate leading
0*
0 ~ 15
Truncate ending
0*

Code ID setting
0x00 ~ 0xff ASCII
code(1 or 2 bytes)
None *
Supplement digits
2 digits
5 digits
2, 5 digits
UCC/EAN 128
2, UCC/EAN 128
5, UCC/EAN 128
All
Disable *
ISBN/ISSN conversion
Enable
Disable *
Industrial 2 of
Read
Enable
0 ~ 64
Max. code length
0*
0 ~ 64
Min. code length
73
0*
Appendix A
0 ~ 15
Truncate leading
0*
0 ~ 15
Truncate ending
0*

Code ID setting
0x00 ~ 0xff ASCII
code(1 or 2 bytes)
Read
Disable
Interleaved 2
Enable *
of 5
Disable/Disable *
Check-sum transmit
Disable/Enable
/verify
Enable /Enable
0 ~ 64
Max. code length
0*
0 ~ 64
Min. code length
0*
0 ~ 15
Truncate leading
0*
0 ~ 15
Truncate ending
0*

Code ID setting
0x00 ~ 0xff ASCII
code(1 or 2 bytes)
Disable *
Standard 2 of 5
Read
Enable
74
Appendix A
Disable/Disable *
Check-sum transmit
Disable/Enable
/verify
Enable /Enable
0 ~ 64
Max. code length
0*
0 ~ 64
Min. code length
0*
0 ~ 15
Truncate leading
0*
0 ~ 15
Truncate ending
0*

Code ID setting
0x00 ~ 0xff ASCII
code(1 or 2 bytes)
Disable *
MSI Plessey
Read
Enable
N/disable *
Check-sum transmit
N/MOD 10
/verify
N/Mod 10,10
N/mod 11,10
Y/ Mod10
Y/ Mod 10,10
Y/ Mod 11/10
75
Appendix A
0 ~ 64
Max. code length
0*
0 ~ 64
Min. code length
0*
0 ~ 15
Truncate leading
0*
0 ~ 15
Truncate ending
0*
<@>
Code ID setting
0x00 ~ 0xff ASCII
code(1 or 2 bytes)
Disable *
UK Plessey
Read
Enable
Disable/Disable
Check-sum transmit
Disable/Enable *
/verify
Enable /Enable
0 ~ 64
Max. code length
0*
0 ~ 64
Min. code length
0*
0 ~ 15
Truncate leading
0*
0 ~ 15
Truncate ending
0*
<@>
76
Appendix A
Code ID setting
0x00 ~ 0xff ASCII
code(1 or 2 bytes)
Disable *
Telepen
Read
Enable
Disable/Disable *
Check-sum transmit
Disable/Enable
/verify
Enable /Enable
0 ~ 64
Max. code length
0*
0 ~ 64
Min. code length
0*
0 ~ 15
Truncate leading
0*
0 ~ 15
Truncate ending
0*

Code ID setting
0x00 ~ 0xff ASCII
code(1 or 2 bytes)
Numeric *
Format
Full ASCII
Disable
UPCA
Read
Enable *
Disable
Check-sum
Enable *
transmission
77
Appendix A
0 ~ 15
Truncate leading
0*
0 ~ 15
Truncate ending
0*

Code ID setting
0x00 ~ 0xff ASCII
code(1 or 2 bytes)
None *
Supplement digits
2 digits
5 digtis
2, 5 digits
UCC/EAN 128
2, UCC/EAN 128
5, UCC/EAN 128
All
None
Truncate/expansion
Truncate leading zero *
Expand to EAN 13
Disable
UPCE
Read
Enable *
Disable
Check-sum
Enable *
transmission
0 ~ 15
Truncate ending
0*

78
Appendix A
Code ID setting
0x00 ~ 0xff ASCII
code(1 or 2 bytes)
None *
Supplement digits
2 digits
5 digits
2, 5 digits
UCC/EAN 128
2, UCC/EAN 128
5, UCC/EAN 128
All
None *
Truncate/expansion
Truncate leading zero
Expand to EAN 13
Expand to UPCA
Disable *
Expansion
Enable
Disable *
UPCE-1
Enable
Disable *
Matrix 25
Read
Enable
Disable/Disable *
Check-sum transmit
Disable/Enable
/verify
Enable /Enable
0 ~ 64
Max. code length
79
0*
Appendix A
0 ~ 64
Min. code length
0*
0 ~ 15
Truncate leading
0*
0 ~ 15
Truncate ending
0*

Code ID setting
0x00 ~ 0xff ASCII
code(1 or 2 bytes)
Disable *
China post
Read
Enable
0 ~ 64
Max. code length
11 *
0 ~ 64
Min. code length
11 *
0 ~ 15
Truncate leading
0*
0 ~ 15
Truncate ending
0*

Code ID setting
0x00 ~ 0xff ASCII
code(1 or 2 bytes)
Disable *
RSS 14
Read
Enable
0 ~ 15
Truncate leading
80
0*
Appendix A
0 ~ 15
Truncate ending
0*

Code ID setting
0x00 ~ 0xff ASCII
code(1 or 2 bytes)
Disable *
UCC/EAN 128
Enable
emulation
Disable *
RSS Limited
Read
Enable
0 ~ 15
Truncate leading
0*
0 ~ 15
Truncate ending
0*

Code ID setting
0x00 ~ 0xff ASCII
code(1 or 2 bytes)
Disable *
UCC/EAN 128
Enable
emulation
Disable *
RSS
Read
Enable
Expanded
0 ~ 99
Max. code length
99 *
0 ~ 99
Min. code length
81
1*
Appendix A
0 ~ 15
Truncate leading
0*
0 ~ 15
Truncate ending
0*

Code ID setting
0x00 ~ 0xff ASCII
code(1 or 2 bytes)
Disable *
UCC/EAN 128
Enable
emulation
Disable *
Italian
Read
Enable
Pharmacode
39
0 ~ 64
Max. code length
12 *
0 ~ 64
Min. code length
9*
0 ~ 15
Truncate leading
0*
0 ~ 15
Truncate ending
0*


Code ID setting
0x00 ~ 0xff ASCII
code(1 or 2 bytes)
Disable *
Leading “A”
Enable
82
Appendix B
Appendix B
Scan Module (2D) Configuration Table
Default (*)
Command1
Indication
Command2
LED indication
0: Disable
1: Enable *
Buzzer indication
Vibrator
Transmission
Value
0: Disable
1: Enable *
0: Disable
1: Enable *
Transmit Code ID
0: None(*)
1: AIM Code ID
2: Symbol Code ID
Scan
17
Timeout
5~99(0.1 sec.)
Default: 99(9.9 sec)
20
Trigger Mode
0:Trigger(*)
7: Hand-Free Mode
9:Auto
21
Picklist Mode
0: Disable(*)
2: Enable
22
5~99(0.1 sec.)
Same Barcode Timeout
Default: 6 (0.6 sec)
23
Mobile
Mode
0: Disable(*)
Phone/Display
83
3: Enable
Appendix B
27
1~10 (default: 10)
Illumination Power Level
28
Decoding Illumination
29
Decode Aiming Pattern
32
Inverse 1D
0: Disable
1: Enable(*)
0: Disable
2: Enable(*)
0: Regular(*)
1: Inverse
2: Inverse Autodetect
10
Code 11
Read
0: Disable(*)
1: Enable
Check Digit Verification
0: Disable(*)
1: 1 Check Digit
2: 2 Check Digits
0: Disable(*)
Transmit Check Digit(s)
1: Enable
11
Code 39
Length 1※1
0 ~ 55 (default: 4)
Length 2※1
0 ~ 55 (default: 55)
Read
0: Disable
1: Enable(*)
Check Digit Verification
Transmit Check Digit
Length 1※1
0: Disable(*)
1: Enable
0: Disable(*)
1: Enable
0 ~ 55 (default: 2)
84
Appendix B
Length 2※1
0 ~ 55 (default: 55)
10
Full ASCII Conversion
0: Disable(*)
1: Enable
19
Code 32 Prefix
0: Disable(*)
1: Enable
20
Trioptic Code 39
12
Code 93
13
Code 128
21
Convert Code
Code 32
Read
0: Disable(*)
1: Enable
0: Disable(*)
39
to
1: Enable
0: Disable(*)
1: Enable
Length 1※1
0 ~ 55 (default: 4)
Length 2※1
0 ~ 55 (default: 55)
Read
0: Disable
1: Enable(*)
Length 1※1
0 ~ 55 (default: 0)
Length 2※1
0 ~ 55 (default: 0)
14
ISBT 128
0: Disable
1: Enable(*)
15
GS1-128
0: Disable
1: Enable(*)
19
ISBT Concatenation
85
0: Disable(*)
1: Enable
Appendix B
2: Auto
20
Check ISBT Table
14
Codabar
1: Enable(*)
21
ISBT Concatenation
Redundancy
2 ~ 20 (default: 10)
Read
0: Disable(*)
1: Enable
Length 1※1
0 ~ 55 (default: 5)
Length 2※1
0 ~ 55 (default: 55)
14
CLSI Editing
0: Disable(*)
1: Enable
15
NOTIS Editing
15
EAN 8/JAN 8
0: Disable
0: Disable(*)
1: Enable
Read
0: Disable
1: Enable(*)
20
Zero Extend
0: Disable(*)
1: Enable
16
EAN 13/JAN 13 Read
0: Disable
1: Enable(*)
18
Interleaved 2 of Read
Check Digit Verification
0: Disable
1: Enable(*)
0: Disable(*)
1: USS Check Digit
2: OPCC Check Digits
Transmit Check Digit
86
0: Disable(*)
1: Enable
Appendix B
20
MSI Plessey
Length 1※1
0 ~ 55 (default: 14)
Length 2※1
0 ~ 55 (default: 0)
Convert to EAN 13
0: Disable(*)
Read
0: Disable(*)
1: Enable
Check Digits
0: One Check Digit(*)
1: Two Check Digits
Transmit Check Digit
23
UPCA
0: Disable(*)
1: Enable
Length 1※1
0 ~ 55 (default: 4)
Length 2※1
0 ~ 55 (default: 55)
Check Digit Algorithm
0: MOD 10/MOD 11
Read
1: MOD 10/MOD 10(*)
0: Disable
1: Enable(*)
Transmit Check Digit
20
UPC-A Preamble
24
UPCE
1: Enable
Read
0: Disable
1: Enable(*)
0: Disable
1:
System
Character
Only(*)
2. System Character and
Country Code
0: Disable
1: Enable(*)
87
Appendix B
25
Matrix 2 of 5
Transmit Check Digit
0: Disable
13
UPC-E1
0: Disable(*)
1: Enable(*)
1: Enable
14
0: Disable(*)
Convert
UPC-E
to
1: Enable
UPC-A
20
0: Disable
Transmit UPC-E1 Check
1: Enable(*)
Digit
21
0: Disable(*)
Convert
UPC-E1
to
1: Enable
UPC-A
22
0: Disable
UPC-E Preamble
1:
System
Character
Only(*)
2. System Character and
Country Code
23
0: Disable
UPC-E1 Preamble
1:
System
Character
Only(*)
2. System Character and
Country Code
0: Disable(*)
Read
1: Enable
Check Digit
0: Disable(*)
1: Enable
Transmit Check Digit
0: Disable(*)
1: Enable
Length 1※1
0 ~ 55 (default: 14)
Length 2※1
0 ~ 55 (default: 0)
88
Appendix B
26
PDF-417
Read
0: Disable
33
MicroPDF
Read
0: Disable(*)
1: Enable(*)
1: Enable
11
Code 128 Emulation
35
UPC/EAN
Bookland EAN
0: Disable(*)
1: Enable
0: Disable(*)
1: Enable
Bookland ISBN Format
0: Bookland ISBN-10(*)
1: Bookland ISBN-13
0: Disable(*)
UCC Coupon Extended
1: Enable
Code
0: Ignore supplemental (*)
Supplemental
1:
Decode
with
Supplemental only
2:
Auto
discriminate
Supplemental
3: Smart Supplemental
Mode
※ Applies to EAN-13
starting with any
prefix
listed
previously
4:
Enable
378/379
Supplemental
5:
Enable
978/979
Supplemental
※ If you select 978
Supplemental Mode
and are scanning
Bookland EAN bar
codes, you should
enable
Bookland
EAN, and select a
format
using
89
Appendix B
Bookland
Format.
ISBN
6:
Enable
414/419/434/439
Supplemental
7:
Enable
977
Supplemental
8:
Enable
491
Supplemental
9:
Supplemental
User-Programmable Type
※ Applies to EAN-13
bar codes starting
with
3-digit
user-defined prefix.
Set this 3-digit prefix
using
User-Programmable
Supplemental.
10:
Supplemental
User-Programmable Type
1 and 2
※ Applies to EAN-13
bar codes starting
with either of two
3-digit user-defined
prefixes. Set the
3-digit
prefixes
using
User-Programmable
Supplemental.
11: Smart Supplemental
Plus
User-Programmable 1
※ Applies to EAN-13
bar codes starting
with any prefix listed
previously or the
user-defined prefix
set using
90
Appendix B
User-Programmable
Supplemental.
12: Smart Supplemental
Plus User-Programmable
1 and 2
※ Applies to EAN-13
bar codes starting
with any prefix listed
previously or one of
the two user-defined
prefixes set using
User-Programmable
Supplemental.
2 ~ 30 (default: 10)
Supplemental
Redundancy
User-Programmable
Supplemental 1
User-Programmable
Supplemental 2
-1 ~ 999(default:-1)
UPC/EAN/JAN
Supplemental AIM
Format
0: Separate
10
Coupon Report
ID
1: Combined(*)
2: Separate Transmission
0: Old Coupon Symbols
1:
New
Coupon
Symbols(*)
2: Both Coupon Formats
11
ISSN EAN
45
Australia Post
-1 ~ 999(default:-1)
0: Disable(*)
1: Enable
Read
0: Disable
1: Enable(*)
0: Auto(*)
91
Appendix B
Format
1: Raw Format
2: Alphanumeric Encoding
3: Numeric Encoding
48
Japan Postal
Read
49
KIX Code
Read
51
USPS
Read
52
UPU
Read
53
Aztec
Read
0: Disable
1: Enable(*)
0: Disable
1: Enable(*)
0: Disable(*)
1: Enable
0: Disable(*)
1: Enable
0: Disable
1: Enable(*)
10
Inverse
0: Regular(*)
1: Inverse
2: Auto
54
Data Matrix
Read
0: Disable
1: Enable(*)
Inverse
0: Regular(*)
1: Inverse
2: Auto
55
Maxicode
Read
58
OCR
Read
0: Disable
1: Enable(*)
0: OCR off (*)
1: OCR-A
2: OCR-B
3. US Currency
4. MICR E13B
92
Appendix B
OCR-A Variant ※2
0: OCR-A Full ASCII(*)
1: OCR-A Reserved 1
2: OCR-A Reserved 2
3: OCR-A Banking
OCR-B Variant ※3
0: OCR-B Full ASCII(*)
1: OCR-B Banking
2: OCR-B Limited
3: OCR-B Travel
Document Version 1
(TD1) 3 Line ID Cards
4: OCR-B Passport
6: OCR-B ISBN 10-Digit
Book Numbers
7: OCR-B ISBN 10 or
13-Digit Book Numbers
8: OCR-B Travel
Document Version 2
(TD2)2-Line ID Cards
9: OCR-B Visa Type A
10: OCR-B Visa Type B
OCR Orientation
OCR Lines
14:Travel Document 2 or
3-Line ID Cards
Auto-Detect
0: OCR Orientation 0(*)
1: OCR Orientation 270
Clockwise
2: OCR Orientation 180
Clockwise
3: OCR Orientation 90
Clockwise
4: OCR Orientation
Omnidirectional
1: OCR 1 Line(*)
2: OCR 2 Line
93
Appendix B
3: OCR 3 Line
OCR Minimum
Characters
OCR Maximum
Characters
OCR Quiet Zone
Inverse OCR
3(*)
Range:3~100
100(*)
Range:3~100
50(*)
Range:20~99
0: Regular Only(*)
1: Inverse Only
2: Autodiscriminate
59
Discrete 2 of 5
Read
0: Disable(*)
1: Enable
Length 1※1
0 ~ 55 (default: 12)
Length 2※1
0 ~ 55 (default: 0)
60
Chinese 2 of 5
Read
0: Disable(*)
61
GS1 Data Bar
GS1 DataBar-14
1: Enable
0: Disable
1: Enable(*)
GS1 DataBar Limited
0: Disable(*)
1: Enable
0: Disable(*)
GS1 DataBar Expanded
1: Enable
Convert to UPC/EAN
GS1 DataBar
Security Level
0: Disable(*)
1: Enable
1: Level 1
Limited
2: Level 2
3: Level 3(*)
94
Appendix B
4: Level 4
62
Korean 3 of 5
Read
63
Postal codes
US Postnet
0: Disable(*)
1: Enable
0: Disable
1: Enable(*)
US Planet
0: Disable
1: Enable(*)
Transmit
US
Check Digit
UK Postal
64
Composite
0: Disable
Postal
1: Enable(*)
0: Disable
1: Enable(*)
0: Disable
Transmit
UK
Postal
1: Enable(*)
Check Digit
0: Disable(*)
Composite CC-C
1: Enable
Composite CC-A/B
Composite TLC-39
UPC Composite Mode
0: Disable(*)
1: Enable
0: Disable(*)
1: Enable
0: UPC Never Linked(*)
1: UPC Always Linked
2: Auto
0: Disable(*)
GS1-128
Emulation 1: Enable
Mode for UCC/EAN
Composite Codes
65
QR Code
Read
0: Disable
1: Enable(*)
0: Regular(*)
95
Appendix B
Inverse
1: Inverse
2: Auto
66
Micro QR
Read
0: Disable
1: Enable(*)
68
Symbology
Redundancy Level
Specific Security
Levels
1: Level 1(*)
2: Level 2
3: Level 3
4: Level 4
Security Level
0: Level 0
1: Level 1(*)
2: Level 2
3: Level 3
6:Normal(*)
Intercharacter Gap Size
10:Large
96
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : A316154
Create Date                     : 2018:10:04 17:56:27+08:00
Modify Date                     : 2018:10:04 17:56:27+08:00
XMP Toolkit                     : Adobe XMP Core 5.6-c015 84.159810, 2016/09/10-02:41:30
Producer                        : Acrobat Distiller 17.0 (Windows)
Creator Tool                    : PScript5.dll Version 5.2.2
Format                          : application/pdf
Title                           : Microsoft Word - PI-1000 Series user manual_EN Draft 20181002
Creator                         : A316154
Document ID                     : uuid:ffda4ba7-1d4d-4fca-888d-0391cd958fe0
Instance ID                     : uuid:b8c84ffc-614f-4d1c-8536-a9fdae4ca3fd
Page Count                      : 105
EXIF Metadata provided by EXIF.tools
FCC ID Filing: NBF-PI-1X60

Navigation menu