Aroot LK-P11W Mobile Printer User Manual LK P11W MANUAL indd

SEWOO TECH CO., LTD. Mobile Printer LK P11W MANUAL indd

User manual

All specifications are subject to change without noticeMOBILE PRINTERMODEL : LK-P11W
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.DISPOSE OF USED BATTERIES ACCORDING TO THE INSTURECITONS
23Table of Contents 1. Product overview 3 2. Unpacking4 3. Installation & Usage 5 3-1. Battery Installation 5 3-2. Battery Charging 6 3-3. Belt Strap Usage 7 3-4. Separation of Battery from the printer 8 3-5. Shoulder Strap Usage 9 3-6. Leather case Usage 10 3-7. Loading the paper 11 3-8. Control Panel Usage 12 3-9. Self Test 13 4. Peripherals Connection 15 4-1. Wifi(802.11b/g) Connection 15 4-2. Interface Cable Connection 16 5. Printer Cleaning 17 6. Product Specification 18 6-1. Specification 181. Product overviewPower switch CHARGER CONNECTOR Cover open button BatterySERIALUSB Paper feed button
452. UnpackingCD Printer case shoulder strap 3. Setting Up the Product3-1. Installing batteryInsert the battery inside printer as shown.Notes: as the battery is not charged at the time of your purchase, charge the battery prior to using the product. (Use the battery charger and/or the optional battery holder.) Push the Open to the direction as pointed by arrow in the image.1 2 3Quick ManualOpen the battery cover and push up the hook to the direction as above.Close the battery cover once you inserted the battery completely.StandardOptionPrinter BatteryRoll paperBelt BuckleUSB Shelded CableRecharger Serial Cable
673-2. Battery Charging 3-3. Belt Hook UsageInsert the belt hook screw into the hole of the belt hook.As shown above, fasten the screw with a screw driver. 1 2Notes: 1. Do not turn on the printer power while you are charging the battery.2. Do not print while charging the battery3. Do not connect the charger to the printer on the process of printing.1. The battery can be charged only when the temperature is 0~40℃ 2. Be sure that the printer is turn off and the battery to be charged is installed.3. Connect the charger to the printer.4. Recharging will now be started.
893-4. Removing batteryPush the Open into the direction indicated with the arrow in the image.Pull out the battery as shown above.1 2 3Push up the hook after opening the battery cover.3-5. Shoulder Strap Usage1 234Insert the strap into the hook on the printer. Place the end of strap into the hook of shoulder strap.After pulling out the end of strap tightly, put it into the clip to be fastened.Fasten the strap in the opposite side with the sample way.
10113-6. Leather Case Usage1 23Open the Velcro Put the printer into the leather case following the direction shown in the Close the Velcro3-7. Loading the media.1 234Press the cover open button and open Place the paper roll as shown.Make sure the paper is placed in right direction.Pull a short length of paper out of the printer and close the cover. Press Feed button and let the paper be arranged property for printing.
12133-8. Control Panel Button Name functionPower buttonThis button is used to turn the printer on and off.When the printer is off, press this button for approximately 2 seconds and it will turn on the power. When you press this button in a state that the printer is on, the printer will turn off.Paper Feed ButtonPaper output can be done manually by pressing this button.Additionally, self-testing and Hexadecimal Dumping can be processed..1. Refer to “3-10” for self test information.2. Refer to the service manual regarding Hexadecimal Dumping.Battery Status Lamp1. If the Batt, LED are Lit, the battery is fully charged.2. If you can hear beeping sound and LED light is turned off, it means that the battery is at the lowest level.3. If the battery is not charged at all, the printer turns off automatically.Error Lamp If the red light is turned on, it means that the paper cover is open. 3-9. Self TestYou can check the printer setting state by doing self test when you set the printer first time or encounter some problems.- Control Circuit, Mechanisms, Print Quality, Rom version.When you can not find the exact cause of problem through self test, investigate on other hardware parts or software. This function is independent of other devices and software.● Self –Test Instructions1.Turn the printer power off an close the printer paper cover.2. While pressing the paper feed button, turn on the printer power.3. The printout is producing4. To add a printout of the Hex-Dump mode, press the paper feed button once more.
1415< Sample Printout of Self Test > 4. Peripherals ConnectionThis product can communicate with other devices via Wi• (802.11b/g) communication and cable.4-1. Wifi(802.11b/g) Connection1. The Printer can be connected to devices equipped with wi• (802.11b/g) communication capacity (PDAs, PCs, etc.)2. Use the wi• (802.11b/g) connection function supported by the device to connect to the printer. Notes: Refer to the wi• (802.11b/g) Manual for more details on connection.
16174-2. Interface Cable Connection1. Connect the interface cable to the cable connector of the printerNotes: Use only cables provided by this manufacturer 2. Connect the interface cable to the USB or Serial port of the device (PDA, PC, etc)SerialUSB5. Printer cleaningIf the interior of the printer is dusty, printing quality can lowered.In such a case, follow the instructions below to clean up the printer.NOTE1. Make sure to turn the printer power off prior to cleaning2. Regarding print head cleaning, as the print head sets very hot during printing, turn off the printer power and wait approximately 10 minute before commencement.3. When cleaning the print head, take care not to touch the heated portion of the print head. The print head subject to be damaged by static electricity.4. Take care not to allow the print head to become scratched and /or damaged in 1. Use an applicator swab moistened with an alcohol solution to clean the print head and remove any dusts.2. Once the cleaning is completed, insert paper roll into the printer few minutes later and close the printer cover.

Navigation menu