Aroot LK-P11W Mobile Printer User Manual LK P11W MANUAL indd
SEWOO TECH CO., LTD. Mobile Printer LK P11W MANUAL indd
Aroot >
User manual
MODEL : LK-P11W MOBILE PRINTER All specifications are subject to change without notice RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTURECITONS 1. Product overview Table of Contents 1. Product overview 2. Unpacking 3. Installation & Usage 3-1. Battery Installation 3-2. Battery Charging 3-3. Belt Strap Usage 3-4. Separation of Battery from the printer 3-5. Shoulder Strap Usage 3-6. Leather case Usage 10 3-7. Loading the paper 11 3-8. Control Panel Usage 12 3-9. Self Test 13 4. Peripherals Connection Paper feed button Cover open button CHARGER CONNECTOR Battery 15 4-1. Wifi(802.11b/g) Connection 15 4-2. Interface Cable Connection 16 5. Printer Cleaning 17 6. Product Specification 18 6-1. Specification Power switch 18 USB SERIAL 3. Setting Up the Product 2. Unpacking 3-1. Installing battery Standard Printer Battery Belt Buckle Push the Open to the direction as pointed by arrow in the image. Recharger Roll paper USB Shelded Cable CD Serial Cable Open the battery cover and push up the hook to the direction as above. 1 2 Quick Manual Option Insert the battery inside printer as shown. Close the battery cover once you inserted the battery completely. Notes: as the battery is not charged at the time of your purchase, charge the Printer case shoulder strap battery prior to using the product. (Use the battery charger and/or the optional battery holder.) 3-2. Battery Charging 3-3. Belt Hook Usage Insert the belt hook screw into the hole of the belt hook. 1. The battery can be charged only when the temperature is 0~40℃ 2. Be sure that the printer is turn off and the battery to be charged is installed. 3. Connect the charger to the printer. 4. Recharging will now be started. Notes: 1. Do not turn on the printer power while you are charging the battery. 2. Do not print while charging the battery 3. Do not connect the charger to the printer on the process of printing. As shown above, fasten the screw with a screw driver. 3-4. Removing battery 3-5. Shoulder Strap Usage Push up the hook after opening the battery cover. Push the Open into the direction indicated with the arrow in the image. 1 2 Pull out the battery as shown above. Place the end of strap into the hook of shoulder strap. Insert the strap into the hook on the printer. 1 2 3 4 After pulling out the end of strap tightly, put it into the clip to be fastened. Fasten the strap in the opposite side with the sample way. 3-6. Leather Case Usage 3-7. Loading the media. Open the Velcro 1 2 Put the printer into the leather case following the direction shown in the Press the cover open button and open 1 2 3 4 Place the paper roll as shown. Make sure the paper is placed in right direction. Close the Velcro Pull a short length of paper out of the printer and close the cover. 10 Press Feed button and let the paper be arranged property for printing. 11 3-8. Control Panel 3-9. Self Test You can check the printer setting state by doing self test when you set the printer first time or encounter some problems. - Control Circuit, Mechanisms, Print Quality, Rom version. When you can not find the exact cause of problem through self test, investigate on other hardware parts or software. This function is independent of other devices and software. ● Self –Test Instructions Button 12 Name function Power button This button is used to turn the printer on and off. When the printer is off, press this button for approximately 2 seconds and it will turn on the power. When you press this button in a state that the printer is on, the printer will turn off. Paper Feed Button Paper output can be done manually by pressing this button. Additionally, self-testing and Hexadecimal Dumping can be processed.. 1. Refer to “3-10” for self test information. 2. Refer to the service manual regarding Hexadecimal Dumping. Battery Status Lamp 1. If the Batt, LED are Lit, the battery is fully charged. 2. If you can hear beeping sound and LED light is turned off, it means that the battery is at the lowest level. 3. If the battery is not charged at all, the printer turns off automatically. Error Lamp If the red light is turned on, it means that the paper cover is open. 1.Turn the printer power off an close the printer paper cover. 2. While pressing the paper feed button, turn on the printer power. 3. The printout is producing 4. To add a printout of the Hex-Dump mode, press the paper feed button once more. 13 4. Peripherals Connection < Sample Printout of Self Test > This product can communicate with other devices via Wi•(802.11b/g) communication and cable. 4-1. Wifi(802.11b/g) Connection 1. The Printer can be connected to devices equipped with wi•(802.11b/g) communication capacity (PDAs, PCs, etc.) 2. Use the wi•(802.11b/g) connection function supported by the device to connect to the printer. Notes: Refer to the wi•(802.11b/g) Manual for more details on connection. 14 15 5. Printer cleaning 4-2. Interface Cable Connection If the interior of the printer is dusty, printing quality can lowered. In such a case, follow the instructions below to clean up the printer. NOTE 1. Make sure to turn the printer power off prior to cleaning 2. Regarding print head cleaning, as the print head sets very hot during printing, turn off the printer power and wait approximately 10 minute before commencement. 3. When cleaning the print head, take care not to touch the heated portion of the print head. The print head subject to be damaged by static electricity. 4. Take care not to allow the print head to become scratched and /or damaged in USB Serial 1. Connect the interface cable to the cable connector of the printer Notes: Use only cables provided by this manufacturer 2. Connect the interface cable to the USB or Serial port of the device (PDA, PC, etc) 1. Use an applicator swab moistened with an alcohol solution to clean the print head and remove any dusts. 2. Once the cleaning is completed, insert paper roll into the printer few minutes later and close the printer cover. 16 17
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 12 XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:920e8f0c-191f-4133-929a-613a8bda7271 Create Date : 2008:08:12 11:45:16Z Metadata Date : 2008:10:28 14:42:52+09:00 Modify Date : 2008:10:28 14:42:52+09:00 Creator Tool : Adobe InDesign CS (3.0.1) Rendition Class : proof:pdf Derived From Instance ID : 8823cd87-5f5f-11dd-8dca-99f52da60cc9 Derived From Document ID : adobe:docid:indd:57df4396-52fc-11dd-965a-b8d0e330156a Document ID : adobe:docid:indd:e9947284-6814-11dd-822a-8c0bcd2302a2 Manifest Link Form : ReferenceStream, ReferenceStream, ReferenceStream Manifest Reference Instance ID : uuid:a35be72d-2e05-11dd-966b-bb62c1927edf, uuid:bc35f6cc-2df4-11dd-966b-bb62c1927edf, uuid:bc35f6d0-2df4-11dd-966b-bb62c1927edf Manifest Reference Document ID : adobe:docid:photoshop:a35be72c-2e05-11dd-966b-bb62c1927edf, adobe:docid:photoshop:bc35f6cb-2df4-11dd-966b-bb62c1927edf, adobe:docid:photoshop:bc35f6cf-2df4-11dd-966b-bb62c1927edf Format : application/pdf Title : LK-P11W MANUAL 영문.indd Trapped : False Creator : Adobe InDesign CS (3.0.1) Producer : Adobe PDF Library 6.0EXIF Metadata provided by EXIF.tools