Atoms Labs AWF53 HD Outdoor PT Network Camera User Manual JSW QSG WAPP JS V1 0

Atoms Labs LLC HD Outdoor PT Network Camera JSW QSG WAPP JS V1 0

User Manual

QUICK START GUIDEKIT CONTENT :Camera Antennax 1x 1x 1Quick Start GuidePower Adapterx 1PRODUCT OVERVIEWSETUP THE CAMERA For iOS For Android 1. APP DownloadDownload and install the "OMGuard HD" APP to your device. 2. Power up The CameraConnect the power wires to the adapter supplied, and wait until the RED LED indicator becomes steady on. This process would be nished within 1 min and make sure the LED is ashing in RED.3a.Wireless Connection(1) In the Wi-Fi setting of your smart device. Choose the Wi-Fi router with prex of HD-xxxxxx (xxxxxx=Camera ID numbers). Then enter the default password 12345678. (2) Launch the APP, tap to add the camera.(3) Tap (QR code icon) and scan the QR code label on the back of the camera to bring up the DID information. Or tap "Search" to locate the camera. (4) Enter the default password 123456.(5) Tap “Save” when you done.(6) Later, APP will request user to modify the default password to private password .Note: Press and hold the “Reset” button for 5 seconds, the system will be restored into factory default.Pan/Tilt WirelessCamera x 1Screw Pack12345x 1Rj45 Connect JackMicro SD Card SlotMicrophoneAntennaLensReset ButtonLight SensorMount Bracket.Ethernet CablePower Cablex 1Hex KeyFRIENDLY REMINDER- For video recording, BE SURE TO use CLASS 10 memory card or above (not included). Other kinds of memory card may cause unexpected results and should be avoided.- Anytime when you nd the camera pan/tile function does not perform properly, calibrate the camera to get correct principle position (refer to step 8 of setup the camera section).- For better performance, please enable the video hardware acceleration function. This function only for Andriod (refer to the app introduction section).AWF53 HD Outdoor PT Network Camera
APP INTRODUCTIONFollow the steps below for Event Playback(1) Tap the icon to access the event list section.(2) Select the time interval for the event list.(3) Select the le you want to playback.(4) If you want to store the les to the mobile device, tap to download the les (Best while under Wi-Fi enviornment due to larger high denation data size).(1) (1)-1(2) (3) (4)3b.Wired Connection(1) Make sure your smartphone is connected your Wi-Fi router.(2) Connect the camera’s Ethernet cable to the Rj45 connect, and power on the camera with adapter.(3) Launch the APP, tap the “Search” to locate the camera. (4) Enter the default password 12345678 and save the settings.(5) Later, APP will request user to modify default password to private password .Note: In soft AP mode, the RED LED long ashes once followed by 2 short ashes. In normal mode, the LED is ashing in RED. 4. Wi-Fi Setting(1) Tap then the advanced setting icon will appear on the screen. (2) Enter the default password :12345678(3) Select your Wi-Fi router, and enter its password.(4) The Camera will oine for around 40 seconds to reboot for Wi connection. When camera connects to Wi-Fi router correctly, the RED LED will stay ON.(5) In the Wi-Fi setting on your smart device again, make sure the Wi-Fi router you are connecting to is the same as the camera. If not, manually assign to it.Note: If you fail to add the camera for several times, press and hold the “Reset” button for 5 seconds to reset it.Live-ViewCamera ListInformationRefreshCamera SettingAdd Camera Live View SnapshotVideo RecordReturnMuteSetup Camera PositionArm/DisarmRj45 ConnectPower AdapterRouterAdvanced Enter Admin Password(default 123456)Choose the appropriate Wi-Fi router on your local network
CAMERA INSTALLATIONEnable video hardware acceleration (For Andriod)(1) In the camera list, tap the (2) Click the click box to enable video hardware acceleration.(1) (2)Note: Before mounting the camera, install the memeory card if you prefer recording to local storage.Products with CE Marking comply with EMC Directive (2014/30/EU); Low Voltage Directive (2014/35/EU); RED (2014/53/EU); ROHS Directive (2011/65/EU) issued by the Commission of the European Community. Compliance with these directives implies conformity to the following European Norms:EMC: EN 301 489LVD: EN 60950Radio: EN 300 328If the camera system no longer functions or can no longer be repaired, it must be disposed of according to the valid statutory regulations. Disposal of spent batteries/accumulators:You are required by law (Battery Ordinance) to return all spent batteries and accumulators. Disposing of spent batteries/accumulators with common household waste is prohibited! Batteries/accumulators that contain hazardous substances are marked with the symbols on the side. These symbols indicate that it is prohibited to dispose of these batteries/accumulators in the household waste. The abbreviations for the respective heavy metals are: Cd=cadmium, Hg=mercury, Pb=lead. You can return spent batteries and accumulators that can no longer be charged to the designated collection points in your community, outlets or wherever batteries or accumulators are sold. Following these instructions will allow you to fulll the legal requirements and contribute to the protection of our environment!(1) Drill the mounting holes by using the aligmaent paper.(2) Insert 4 screw anchors into the wall.(3) Insert 2 screws into the screw anchors, reserved space 8 to 10 mm. Then Hang the camera on 2 screws.(4) Fasten 4 screws by using hex key.1 243Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority tooperate the equipment.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCCRules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with theinstructions, may cause harmful interference to radio communications. However, there is no guarantee that interference willnot occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, whichcan be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one ormore of the following measures:-- Reorient or relocate the receiving antenna.-- Increase the separation between the equipment and receiver.-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.-- Consult the dealer or an experienced radio/TV technician for helpThis device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1)this device may notcause harmful interference, and (2) this device must accept any interference received, including interference that may causeundesired operation

Navigation menu