Autec s r l FJMNZ422 Transceiver unit User Manual 5

Download:
Mirror Download [FCC.gov]
Document ID	2994545
Application ID	w2/pzXmx7j8dgGwpM2Unyw==
Document Description	User Manual 5
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	93.6kB (1169972 bits)
Date Submitted	2016-05-18 00:00:00
Date Available	2016-05-18 00:00:00
Creation Date	2015-07-28 08:48:36
Producing Software	Adobe PDF Library 10.0.1
Document Lastmod	2015-07-28 08:48:41
Document Title	User Manual 5
Document Creator	Adobe InDesign CS6 (Windows)

Original instructions
Dynamic Series
Part C: FJMﾠtransmittingﾠunit
Index
Description .............................................................................................................
Technical data ........................................................................................................
Technical data sheet ..............................................................................................
Plates ......................................................................................................................
Light signals ...........................................................................................................
Actuators for the display .......................................................................................
6.1 DISPLAY pushbutton ........................................................................................
6.2 Six pushbuttons ................................................................................................
Malfunction signalled by the transmitting unit ....................................................
AUTEC
LIFJME00-06
2
Description
Description
aB
e F G
TU ID: XXXXXX
MANIF. DATE XXXX
POWER SUPPLY.....................................................7.2V
RADIO MODULE..............................................FSARTBEU2
FREQUENCY RANGE......................................863-870MHz
RF OUTPUT POWER.....................................<25mW ERP
PROTECTION DEGREE...............................................IP65
S/N:
XXXXXX
TA1194-00 A0TARG01P0937
Display or LED (if present)
Connector for wire control (if present)
LED
Battery
Actuators (joysticks, selectors,
pushbuttons)
Radio remote control identification plate
(if the “Key ID 0-1” is present)
STOP pushbutton
Power keyswitch
Transmitting unit identification plate
START pushbutton
Technical data plate
Battery housing
Radio remote control identification
plate (if the “ID internal tx memory” is
present)
LIFJME00-06
AUTEC - Dynamic Series
Technical data
Technical data
Power supply (battery MBM06MH) .......................................................................... 7.2V
Power supply (battery LPM02) ................................................................................ 7.4V
Power supply (battery LPM04) ................................................................................ 7.4V
Antenna ................................................................................................................... internal
Housing material ........................................................................................... PA 6 (20%fg)
Protection degree ........................................................................................ IP65 (NEMA 4)
Dimensions ................................................................... 310x210x190mm (12.2x8.3x7.5In)
Weight ............................................................................................................ 2.5kg (5.5Lb)
Run time at 20°C (68°F):
- with battery MBM06MH................................................................................................ 11h
- with battery MBM06MH and monochromatic display 2.7"............................................... 9h
- with battery LPM02................................................................................................... 18.5h
- with battery LPM02 and monochromatic display 2.7".................................................... 15h
- with battery LPM04...................................................................................................... 35h
- with battery LPM04 and monochromatic display 2.7".................................................... 28h
- with battery LPM04 and color display 4.3"...................................................................... 8h
Technical data sheet
The technical data sheet contains the transmitting unit configuration and shows the matching
between commands sent and machine functions/movements. It also contains the wiring
diagram showing the connection between the receiving unit and the machine.
Each technical data sheet must be filled in, checked and signed by the installer, who is
responsible for a correct wiring.
A technical data sheet must always be kept toghether with this manual (always keep a copy
of the technical data sheet when it is used for administrative purposes).
The wiring of the receiving unit outputs must always reflect the wiring
indicated in the technical data sheet.
AUTEC - Dynamic Series
LIFJME00-06
4
Plates
Plates
The transmitting unit has the following plates:
Plate
Position
Content
Key ID 0-1 (if present).
radio remote control
identification plate
Battery housing (if the
“ID internal tx memory” is
present).
Radio remote control serial number
(S/N).
transmitting unit
identification plate
Battery housing.
Manufacturing year, bar code and
transmitting unit identification number
(TU ID).
technical data plate
Battery housing.
MODEL, TYPE and main transmitting
unit technical data, marking and possible
radio remote control marks.
LIFJME00-06
AUTEC - Dynamic Series
Light signals
Light signals
The FJM transmitting units may have two or four LEDs.
Red LED
Green LED
LEDs for Data
Feedback function
In both cases, a green LED [B] and a red LED [A] are always available, and they provide
information regarding the radio remote control.
If the unit has 4 LEDs, the side LEDs [C] are red and provide information coming from the
machine (Data Feedback function).
Symbol
Meaning
This symbol indicates the red LED [A].
This symbol indicates the green LED [B].
The green LED [B] …
…is off.
… blinks fast
… blinks slowly
AUTEC - Dynamic Series
Meaning
The transmitting unit is switched off.
The transmitting unit is switched on and there is no radio
link.
The radio remote control is started and the radio link is
present.
LIFJME00-06
6
Light signals
The red LED [A]a …
…is off.
The transmitting unit works correctly.
… blinks
The battery is nearly flat.
... illuminates for 2 secondsb
a.
b.
Meaning
The transmitting unit does not work correctly.
... blinks onceb
At power on, the transmitting unit detects that the STOP
pushbutton is activated or damaged.
... blinks twiceb
At power on, the transmitting unit detects that one of the
commands D2-D20 or SAFETY is activated or damaged
(see technical data sheet).
... blinks three timesb
At power on, the transmitting unit detects that the battery
is flat.
... blinks four timesb
At power on, the transmitting unit detects that one of
the commands A1-A8, L1-L8 and H1-H8 is activated or
damaged (see technical data sheet).
An acoustic signal is also heard when the red LED [A] is illuminated.
After this signal, the transmitting unit switches off.
LIFJME00-06
AUTEC - Dynamic Series
Actuators for the display
Actuators for the display
If the transmitting unit has a display, it can be used through a pushbutton (see paragraph
6.1 ) or six pushbuttons (see paragraph 6.2).
Functions carried out by these actuators are decided by the machine manufacturer: the user
must be properly trained about them.
6.1
DISPLAY pushbutton
This pushbutton is used to:
-- activate the display lighting, if it is off
-- cyclically scroll the information on the display in two different
modes:
-- manual: the lines scroll up each time the pushbutton is
pressed
-- automatic: when the DISPLAY pushbutton is pressed for
3 seconds, the lines scroll automatically. If the DISPLAY
pushbutton is pressed again, it switches back to manual
mode.
It is not possible to scroll the lines if icons only are displayed.
The display lighting stays on for a time set by the machine
manufacturer.
Symbol
Meaning
This symbol identifies the DISPLAY pushbutton.
The DISPLAY pushbutton may perform different functions from that described
above according to what defined by the machine manufacturer.
AUTEC - Dynamic Series
LIFJME00-06
8
6.2
Actuators for the display
Six pushbuttons
Functions carried out by the six pushbuttons in order to manage the display, are configurable
and are defined by the machine manufacturer.
LIFJME00-06
Red LED
Green LED
LEDs for Data
Feedback function
Pushbuttons to
manage the 4.3"
display
AUTEC - Dynamic Series
Malfunction signalled by the transmitting unit
Malfunction signalled by the transmitting unit
Use the light signals on the transmitting unit to identify the radio remote control malfunction.
If the problem persists after the suggested solution has been carried out, contact the support
service of the machine manufacturer.
Signals
Possible reason
Solutions
The green LED does
not switch on when the
START pushbutton is
pressed, even though
both the battery and the
power keyswitch are
inserted.
The battery is flat.
Replace the battery with a charged one.
The green LED blinks
fast.
No radio link.
Bring the transmitting unit closer to the
receiving unit.
The red LED switches
on for 2 seconds and
then the unit switches
off.
The transmitting unit does
not work correctly.
Perform the procedure to save the
addressc.
Contact the support service of the
machine manufacturer.
The red LED blinks
once during start up.
The STOP pushbutton is
locked or damaged.
Unlock the STOP pushbutton.
If this signal persists, contact the support
service of the machine manufacturer.
The red LED blinks
twice during start up.
At least one of the
actuators corresponding
to commands D2-D20
and SAFETY is activated
or damaged.
Bring the actuators to the rest position. If
this signal persists, contact the support
service of the machine manufacturer.
The red LED blinks
three times during start
up.
The battery is flat.
Replace the battery with a charged one.
The red LED blinks four
times during start up.
At least one of the
actuators corresponding
to commands A1-A8, L1L8, H1-H8 and SAFETY
is activated or damaged.
Bring the actuators to the rest position. If
this signal persists, contact the support
service of the machine manufacturer.
c.
Procedure to save the address
-- press the STOP pushbutton
-- press the START pushbutton and do not release it until the green LED switches off
-- unlock the STOP pushbutton
AUTEC - Dynamic Series
LIFJME00-06


---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 5.3-c011 66.145661, 2012/02/06-14:56:27
Create Date                     : 2015:07:28 08:48:36+02:00
Metadata Date                   : 2015:07:28 08:48:41+02:00
Modify Date                     : 2015:07:28 08:48:41+02:00
Creator Tool                    : Adobe InDesign CS6 (Windows)
Instance ID                     : uuid:ee6381f5-9c0c-43a9-8d5d-cc6ac15a0113
Original Document ID            : xmp.did:3E97F9BFF011E111AF74C00038EEA0BF
Document ID                     : xmp.id:D8D1BBA7F434E511ABB5B9545D11DE59
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:D7D1BBA7F434E511ABB5B9545D11DE59
Derived From Document ID        : xmp.did:D7D1BBA7F434E511ABB5B9545D11DE59
Derived From Original Document ID: xmp.did:3E97F9BFF011E111AF74C00038EEA0BF
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CS6 (Windows)
History Changed                 : /
History When                    : 2015:07:28 08:48:36+02:00
Format                          : application/pdf
Producer                        : Adobe PDF Library 10.0.1
Trapped                         : False
Page Layout                     : SinglePage
Page Count                      : 12
Creator                         : Adobe InDesign CS6 (Windows)

EXIF Metadata provided by EXIF.tools