Automatic Technology TRX02403 NTR-1V1 NETWORK TRANSCEIVER User Manual
Automatic Technology (Australia) Pty. Ltd. NTR-1V1 NETWORK TRANSCEIVER Users Manual
Users Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3079624 |
| Application ID | Q5VqBczO+6rATXYwS3ZknA== |
| Document Description | Users Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 65.9kB (823807 bits) |
| Date Submitted | 2016-07-28 00:00:00 |
| Date Available | 2016-07-28 00:00:00 |
| Creation Date | 2016-07-21 11:22:07 |
| Producing Software | Adobe PDF Library 10.0.1 |
| Document Lastmod | 2016-07-21 11:22:10 |
| Document Title | Users Manual |
| Document Creator | Adobe InDesign CS6 (Windows) |
Smart Phone Control Kit Transceiver Installation Instructions Garage Door Openers CLASS B DEVICE TRANSCEIVER KIT NTR-1V1 - ORDER NO. 14825 ITEM DESCRIPTION QTY NETWORK TRANSCEIVER NTR-1V1 AY TIMING HARNESS 400MM VR12 AY TAPTITE SCREW “P” M4 X 12 VELCRO 20 X 50 Any changes or modifications not expressively approved by Automatic Technology could void the user’s authority to operate this equipment. CAN ICES-3 (B)/NMB-3 (B) This equiment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encourage to try to correct the interference by one or more of the following measures: •• Reorient or relocate the receiving antenna •• Increase the separation between the equipment and receiver •• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. •• Consult the dealer or experienced radio/TV technician for help. This device allows for unattended operation of the door when not in line-of-sight of the door opener. The door may operate unexpectedly, therefore do not allow anything to stay in or near the path of the door. When the door is not operating automatically, watch the door when it is moving and keep people away until the door is completely opened or closed. Contact with the moving door can cause serious personal injury or damage to property. Your opener must be fitted with SAFETY BEAMS. Safety Beams detect any obstructions in the door’s path and override automatic operation if one presents. These must be installed as in accordance with UL 325 and CSA C222.2 No 247. This is in addition to regular professional servicing, and monthly obstruction tests as detailed in your opener’s Home Owners Manual. Important Safety Instructions WARNING! • • ELECTROCUTION! • DO NOT attempt to disassemble, repair or modify the product. This will invalidate the warranty. Do not allow children to play with the Base Station or your smart phone if the B&D phone app has been installed. • Keep the device away from water and other liquids. In the event that water or other liquids enter the device, power off he product immediately and clean the device. To reduce the risk of fire or electric shock, do not expose this device to rain or moisture. The device should not be exposed to dripping or splashing. DO NOT remove the cover as there are no user-serviceable parts inside. • • • Ensure ladder is the correct type for job. Ensure ladder is on flat ground. Ensure user has 3 points of contact while on ladder. • CAUTION: Fall from ladder Doc # 160064_02 Part # N/A Released 21/07/16 AM-808 Installation Instructions Grommet Back cover screw Network / Programmer Pin AM-808 Door Openers ITEM DESCRIPTION QTY NETWORK TRANSCEIVER NTR-1V1 AY TIMING HARNESS 400MM VR12 AY VELCRO 20 X 50 Preparation of Opener a. Disconnect the power supply to the opener. b. Remove the cover or back cover via screw at top. c. Remove the grommet out of the chassis. d. Cut (1) one side of the grommet with a knife or scissors. e. Slide the network timing harness 2 into the cut in the grommet. f. Refit grommet to chassis by sliding the harness through hole before fitting grommet. g. Connect the harness to the network / programmer pin on the control board. h. Refit the cover. Mount and connect Transceiver a. Plug the other end of the harness into the transceiver 1 . b. Using the velcro 4 stick the transceiver 1 on the top of the opener as shown. WARNING: DO NOT drill into the chassis or covers. No screws are required to secure the transceiver. Re-setup and Test the Opener a. Reconnect power and remove the button cover. b. Setting Limits: i. If limits have not been set, follow the openers installation sheet to set limits. ii. If limits were set previously, clear limits and follow openers installation sheet to set limits. c. Refer to the Smart Phone Control Kit User Guide to set up network capabilities. AM-888 Installation Instructions Affix with screw here Aerial slot AM-888 Door Openers ITEM DESCRIPTION QTY NETWORK TRANSCEIVER NTR-1V1 AY TIMING HARNESS 400MM VR12 AY TAPTITE SCREW “P” M4 X 12 Preparation of Opener a. Disconnect the power supply to the opener. b. Open the side cover on the right hand side (looking from back of unit). c. Connect the harness 2 to the network / programmer pin on the control board. d. Place the transceiver 1 inside the cover, threading the aerial through the slot provided and affix with one (1) Taptite Screw 3 . e. Refit the cover. Re-setup and Test the Opener a. Reconnect power and remove the button cover. b. Setting Limits: i. If limits have not been set, follow the openers installation sheet to set limits. ii. If limits were set previously, clear limits and follow openers installation sheet to set limits. c. Refer to the Smart Phone Control Kit User Guide to set up network capabilities. To comply with FCC/IC RF exposure limits for general population / uncontrolled exposure, the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. 6 - 8 Fiveways Boulevard, Keysborough, VIC, Australia 3173 P: 1300 133 944 E: sales@automatictechnology.com.au W: www.automatictechnology.com.au © April 2015 Automatic Technology (Australia) Pty Ltd. All rights reserved. No part of this document may be reproduced without prior permission. In an ongoing commitment to product quality we reserve the right to change specification without notice. E&OE.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 5.3-c011 66.145661, 2012/02/06-14:56:27 Create Date : 2016:07:21 11:22:07+10:00 Metadata Date : 2016:07:21 11:22:10+10:00 Modify Date : 2016:07:21 11:22:10+10:00 Creator Tool : Adobe InDesign CS6 (Windows) Instance ID : uuid:3d1d406b-d7b3-47c8-b0ac-17806a33661c Original Document ID : xmp.did:E94C461FE443E211B090F5638E375A9B Document ID : xmp.id:50E3722EDF4EE6119457A8E03187D63D Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:4FE3722EDF4EE6119457A8E03187D63D Derived From Document ID : xmp.did:1AD9AE2ADA4EE6119457A8E03187D63D Derived From Original Document ID: xmp.did:E94C461FE443E211B090F5638E375A9B Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CS6 (Windows) History Changed : / History When : 2016:07:21 11:22:07+10:00 Format : application/pdf Producer : Adobe PDF Library 10.0.1 Trapped : False Page Count : 4 Creator : Adobe InDesign CS6 (Windows)EXIF Metadata provided by EXIF.tools