Automotive Data Solutions TR3450AF CAR ALARM (TWO WAY) User Manual
Automotive Data Solutions Inc. CAR ALARM (TWO WAY)
user manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3036665 |
| Application ID | +YaAOMe7K+4wbPhRBapW0Q== |
| Document Description | user manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 376.53kB (4706601 bits) |
| Date Submitted | 2016-06-22 00:00:00 |
| Date Available | 2016-06-22 00:00:00 |
| Creation Date | 2016-06-15 16:18:35 |
| Producing Software | Adobe PDF Library 15.0 |
| Document Lastmod | 2016-06-20 13:22:18 |
| Document Title | user manual |
| Document Creator | Adobe InDesign CC 2015 (Macintosh) |
® hc 3 2016/06 OWNER’S MANUAL IDATASTART OWNER’S GUIDE WELCOME TO IDATASTART Congratulations on the purchase of your iDataStart HC3 remote start system. Please take a moment to review the following table of contents to help you quickly access the information you need. Remote overview Remote functions & confirmations 4-6 Programming a new remote Upgrading your FLEX remote configuration Replacing remote batteries Remote starting from your factory key fob Adjusting engine runtime settings Key takeover following remote start When servicing your vehicle (Valet Mode) Remote start troubleshooting 10 Vehicle shutdown troubleshooting 11 Limited lifetime warranty 12 FCC statement 13 SAR information statement 14-15 IC statement 15 Headquartered in Montreal, Canada, Automotive Data Solutions Inc. (ADS) is a privately held company specialized in the development and marketing of remote start and audio integration solutions destined for the automotive aftermarket. ADS’ award-winning products (marketed under the iDatalink®, iDatalink Maestro® and iDataStart® brands) are sold and installed through a network of Authorized Dealers across North America, South America, Europe and Russia. For more information about ADS’ products and services, visit www.adsdata.ca. CUSTOMER SUPPORT: 866.427.2999 / WWW.IDATASTART.COM IDATASTART OWNER’S GUIDE REMOTE OVERVIEW Your iDataStart HC3 remotes can be programmed in one of three configurations listed below. Please take a moment to familiarize yourself with their general features. TOP LED (TX) BUTTON LED (RX) CASING RELEASE BUTTON Remote model TR3450AF Buttons FLEX configuration FLEX 1W FLEX 2W FLEX 2WX Communication / Range 1-Way / Half-Mile* 2-Way / Half-Mile* 2-Way / 1-Mile* Range upgrade options FLEX 2W or 2WX FLEX 2WX -- Red Top LED Orange Top LED Amber Top LED -- Amber Button LED + Chime Amber Button LED + Chime Transmit confirmation (TX) Receive confirmation (RX) Batteries required Avg. battery Life Warranty 1 x CR2450 15-20 months 10-15 months 1 year *Maximum range listed. May vary by location. CUSTOMER SUPPORT: 866.427.2999 / WWW.IDATASTART.COM 8-15 months IDATASTART OWNER’S GUIDE REMOTE FUNCTIONS & CONFIRMATIONS Thanks to their multiplexing technology, iDataStart HC3 remotes offer over 30 functions using only 5 buttons. In order to get the most out of your remotes, please take a moment to get acquainted with the following functions: NOTES: 1. 2. 3. 4. 5. 6. 7. 8. Available functions must be enabled by an Authorized Dealer during installation to be functional on remote Non-highlighted icons = Press & release button Highlighted (grey) icons = Press & hold button for 2.5 seconds Coma (,) between icons = Press buttons one after the other Plus (+) between icons = Press buttons simultaneously Timeout between each button press = 3 seconds Function* = Available in 2nd Car Mode Confirmations are only available with FLEX 2W and FLEX 2WX remote configurations. BUTTON(S) FUNCTION CONFIRMATION (2-WAY ONLY) FUNCTION DESCRIPTION Lock & Arm* 1 chime + 1 flash Secure your vehicle by locking the doors and arming the alarm. Unlock & Disarm* 2 chimes + 2 flashes Access your vehicle by unlocking the doors and disarming the alarm. 1 chime + 1 flash Trigger the panic siren. -Query* Panic* AUX 5* To be completed by Authorized Dealer if applicable Trunk Release Release the trunk or hatch. CUSTOMER SUPPORT: 866.427.2999 / WWW.IDATASTART.COM IDATASTART OWNER’S GUIDE BUTTON(S) FUNCTION Engine Start/ Stop* CONFIRMATION (2-WAY ONLY) FUNCTION DESCRIPTION 4 chimes + 4 flashes (Button LEDs will also flash intermittently while engine is running) Start and stops the engine. AUX 1 To be completed by Authorized Dealer if applicable AUX 2 To be completed by Authorized Dealer if applicable AUX 3 To be completed by Authorized Dealer if applicable AUX 4 To be completed by Authorized Dealer if applicable 2nd Car Mode Control two iDataStart-equipped vehicles using one remote. Works with all functions marked with an asterisk (*). Silent Lock* Disable the vehicle’s horn and alarm siren when pressing the ‘Lock’ button. Silent Unlock* Disable the vehicle’s horn and alarm siren when pressing the ‘Unlock’ button. ,* Valet Mode ON/OFF 1 chime ON 2 chimes OFF Seamlessly extends your engine runtime without restarting your vehicle. Runtime Extend Turn off remote start and security features when servicing your vehicle or valet parking. Keyless entry features remains functional. Mute ON/OFF 1 chime ON 2 chimes OFF Disable the vehicle’s horn and alarm siren even when alarm is triggered. Remote will still receive alarm notification. Shock Sensor ON/OFF 1 chime ON 2 chimes OFF Disable shock sensors if installed. CUSTOMER SUPPORT: 866.427.2999 / WWW.IDATASTART.COM IDATASTART OWNER’S GUIDE BUTTON(S) FUNCTION CONFIRMATION (2-WAY ONLY) FUNCTION DESCRIPTION Ignition Lock ON/OFF 1 chime ON 2 chimes OFF Automatically locks doors when engine is running. Passive Lock & Arm ON/OFF 1 chime ON 2 chimes OFF Automatically locks & arms your vehicle 60 seconds after you unlock it. Turbo ON/OFF 1 chime ON 2 chimes OFF Cool down your turbo before turning the engine off. Programmable runtime from 1 to 4 minutes. Weather Start ON/OFF 1 chime ON 2 chimes OFF Set your vehicle to automatically remote start every 2, 3 or 4 hours (programmable) or from a temp. sensor sold separately. Lock Remote 1 chime + 1 flash Disable all functions on your remote. Pressing a button will generate 6 chimes + 6 flashes. Available with 2-way remote only. Unlock Remote 2 chimes + 2 flashes Enable all functions on your remote. Available with 2-way remote only. Mute Remote ON/OFF 1 chime ON 2 chimes OFF Disable the chime when pressing any button on your remote. Available with 2-way remote only. PROGRAMMING A NEW REMOTE Are you replacing a lost or damaged remote or simply adding an extra remote to your iDataStart system? Please take note of the following: 1. A functional iDataStart HC3 system must already be installed in your vehicle. 2. All new remotes must be installed by an iDataStart HC3 Authorized Dealer. 3. A maximum of 4 remotes can be programmed to your iDataStart system. Ask your iDataStart HC3 Authorized Dealer for compatible remotes. CUSTOMER SUPPORT: 866.427.2999 / WWW.IDATASTART.COM IDATASTART OWNER’S GUIDE UPGRADING YOUR FLEX REMOTE CONFIGURATION Want to upgrade the confguration of your iDataStart HC3 remotes? Please take note of the following: 1. A functional iDataStart HC3 system with FLEX 1W or FLEX 2W remote configuration must already be installed in your vehicle. 2. All upgrades must be programmed by an iDataStart Authorized Dealer. Upgrade fees will apply. REPLACING REMOTE BATTERIES Follow the steps below to replace the batteries in your iDataStart HC3 remotes OR scan the QR code below to view a video tutorial. 1. 2. 3. 4. 5. Insert a 25 cent coin into the hollow (bottom left) corner of your iDataStart remote. Gently twist the coin and move it along the seam until the casing pops open. Use your coin to pry open the rest of the case perimeter. Slide the old battery out of its enclosure and replace with the new battery. Snap top and bottom casings back together using your hands. http://q-r.to/1h9x REMOTE STARTING FROM FACTORY KEY FOB Available on most vehicles, your iDataStart HC3 system can enable remote start functionality from your factory key fob as follows: BUTTON PRESS FUNCTION 3x rapidly Start engine 3x rapidly Stop engine Remote start range will vary by key fob. Ask your iDataStart HC3 Authorized Dealer for details. CUSTOMER SUPPORT: 866.427.2999 / WWW.IDATASTART.COM IDATASTART OWNER’S GUIDE ADJUSTING ENGINE RUNTIME SETTINGS Once remote started from your factory key fob or long-range remote, your vehicle will run for the programmed ‘runtime’ setting. The default runtime is 15 minutes but it can also be programmed for 3, 5, 10, 25, 30 or 35 minutes. If you wish to change your remote start runtime setting, contact your iDataStart Authorized Dealer. KEY TAKEOVER FOLLOWING REMOTE START Available on some vehicles, the ‘key takeover’ procedure ensures that your engine does not turn off when entering the car during the remote start runtime, following a remote start command. Follow the instructions below or scan the QR code to view a video tutorial. For Standard Key Vehicles 1. 2. 3. 4. Unlock and enter vehicle Close doors Insert key into ignition and turn ignition to ON position Press foot brake http://q-r.to/2ixD For Push-To-Start Vehicles 1. Unlock and enter vehicle with valid smartkey 2. Close doors 3. Press foot brake http://q-r.to/2iwz NOTE: To prevent your vehicle from shutting down, complete the steps above within the programmed delay time (45 seconds, 90 seconds, 3 minutes or 4 minutes). Key takeover procedure may vary by vehicle, ask your iDataStart HC3 Authorized Dealer for deatails. CUSTOMER SUPPORT: 866.427.2999 / WWW.IDATASTART.COM IDATASTART OWNER’S GUIDE WHEN SERVICING YOUR VEHICLE To ensure safety during vehicle servicing, the remote starter must be placed in ‘Valet Mode’. The ‘Valet Mode’ will disable remote start functionality. To activate or deactivate the ‘Valet Mode’, follow the instructions below or scan the QR codes to view a video tutorial. With Vehicle Key FUNCTION Valet Mode ON Valet Mode OFF ACTION # OF PARKING LIGHT FLASHES Cycle ignition OFF/ON 2x rapidly, then press brake 3x. http://q-r.to/2aDQ With iDataStart Remote FUNCTION Valet Mode ON Valet Mode OFF ACTION # OF PARKING LIGHT FLASHES Turn ignition ON, then press http://q-r.to/244h With iDataStart Antenna FUNCTION Valet Mode ON Valet Mode OFF ACTION # OF LED & PARKING LIGHT FLASHES Turn ignition ON, then press & hold button for 5 seconds http://q-r.to/1pmn CUSTOMER SUPPORT: 866.427.2999 / WWW.IDATASTART.COM IDATASTART OWNER’S GUIDE 10 REMOTE START TROUBLESHOOTING If your iDataStart HC3 remote fails to start the vehicle, the parking lights* will flash three times immediately, then flash a number of times according to the errors below: # OF PARKING LIGHT FLASHES DIAGNOSTIC SOLUTION 3+1 Engine is already running Turn engine OFF 3+2 Key in ignition at ON position Remove key from ignition 3+4 Trunk is open Close trunk 3+5 Foot brake is ON Release foot brake 3+6 Hood is open Close hood 3+8 Tach failure Contact Authorized Dealer 3 + 10 System is in Valet Mode Exit Valet Mode 3 + 11 CAN communication failure Contact Authorized Dealer NOTE: Parking lights must be connected at installation to enable troubleshooting flashes. Ask your Authorized Dealer for details. CUSTOMER SUPPORT: 866.427.2999 / WWW.IDATASTART.COM IDATASTART OWNER’S GUIDE 11 VEHICLE SHUTDOWN TROUBLESHOOTING If the remote start sequence has been completed and the vehicle shuts down, the vehicle’s parking lights will flash 4 times immediately, then flash a number of times according to the errors below: # OF PARKING LIGHT FLASHES DIAGNOSTIC SOLUTION 4+1 No engine rev detected Turn ignition ON before trying to remote start 4+3 Foot brake detected Release foot brake 4+4 Hood open detected Close hood 4+5 Engine revving over 3000 RPM Check your accelerator pedal 4+6 Glow plug error Contact Authorized Dealer 4+7 Vehicle speed sensor error Contact Authorized Dealer 4+8 ‘Check Engine’ light detected Clear ‘Check Engine’ code 4+9 Low fuel detected Add fuel 4+10 Door open detected Close door 4+11 CAN communication failure Contact Authorized Dealer 4+13 Key takeover not allowed Key fob not detected OR Takeover procedure not completed correctly OR takeover is not available for your vehicle 4+14 Module overheat protection Contact Authorized Dealer CUSTOMER SUPPORT: 866.427.2999 / WWW.IDATASTART.COM IDATASTART OWNER’S GUIDE 12 LIMITED LIFETIME WARRANTY Automotive Data Solutions Inc. (“ADS”) warrants to the original purchaser of the iDataStart product that the following components product shall be free of defects in material and workmanship under normal use and circumstances: Control module and installation harnesses For as long as the original purchaser owns the vehicle in which it was originally installed. Remote transmitters and antenna For the period of one (1) year from the date of original installation. Excludes battery replacement. In the event of any product malfunction during the Warranty period, the original purchaser must return to the Authorized Dealer where it was originally purchased with the original proof of purchase. If a malfunction is detected, the Authorized Dealer will elect to repair or replace the product at its discretion. Labor costs may be applicable and are at the discretion of the Authorized Dealer. THE LIMITED LIFETIME WARRANTY IS AUTOMATICALLY VOID IF: • • • • An original proof of purchase is not provided when servicing the product during the warranty period; The date code and/or serial number is defaced, missing, or altered; The iDataStart product is transferred to another vehicle; The vehicle in which the product was originally installed is transferred to a new owner. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the installation or operation of an iDataStart product. CUSTOMER SUPPORT: 866.427.2999 / WWW.IDATASTART.COM IDATASTART OWNER’S GUIDE 13 FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • • • • Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. CUSTOMER SUPPORT: 866.427.2999 / WWW.IDATASTART.COM 14 IDATASTART OWNER’S GUIDE SAR INFORMATION STATEMENT Your wireless CAR ALARM (TWO WAY) is a radio transmitter and receiver. It is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general population. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons, regardless of age and health. The exposure standard for wireless CAR ALARM (TWO WAY) employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 4.0 W/kg. Tests for SAR are conducted with the CAR ALARM (TWO WAY) transmitting at its highest certified power level in all tested frequency bands. Although the SAR is determined at the highest certified power level, the actual SAR level of the CAR ALARM (TWO WAY) while operating can be well below the maximum value. This is because the CAR ALARM (TWO WAY) is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output. Before a CAR ALARM (TWO WAY) model is available for sale to the public, it must be tested and certified to the FCC that it does not exceed the limit established by the government adopted requirement for safe exposure. The tests are performed in positions and locations (e.g., at the ear and worn on the body) as required by the FCC for each model. The highest SAR value for this model CAR ALARM (TWO WAY) when tested for use at the extremity is 0.030W/Kg. While there may be differences between the SAR levels of various CAR ALARM (TWO WAY) and at various positions, they all meet the government requirement for safe exposure. The FCC has granted an Equipment Authorization for this model CAR ALARM (TWO WAY) with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this model CAR ALARM (TWO WAY) is on file with the FCC and can be found under the Display Grant section of http://www.fcc.gov/oet/fccid after searching on FCC ID 2AEPJ-TR3450AF. Additional information on Specific Absorption Rates (SAR) can be found on the Cellular Telecommunications Industry Association (CTIA) website at http://www.wow-com.com.* CUSTOMER SUPPORT: 866.427.2999 / WWW.IDATASTART.COM CAR ALARM Le présentappareilestconforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitationestautorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareildoit accepter tout brouillageradioélectriquesubi, mêmesi le brouillageest susceptible d'encompromettre le fonctionnement. Cetéquipementestconforme aux limitesd'exposition aux rayonnements de la IC définies pour un environnement non contrôlé. L'utilisateur final doit respecter les instructions de fonctionnement spécifiques pour satisfaire la conformité aux expositions RF. Cetémetteur ne doit pas être co-localiséesouopérant en conjonction avec uneautreantenneouémetteur. L'appareil mobile estconçu pour répondre aux exigences en matièred'exposition aux ondes radio établies par la Federal Communications Commission (Etats-Unis). Cesexigencesdéfinissent la valeur SAR limite à 4.0 W/kg, en moyenne pour un gramme de tissu.La valeur SAR la plus élevée pour cemodèled’alarme de voiture (deuxvoies) lorsqu’ilesttesté pour uneutilisation à l’extrémitéest de 0.030W/ Kg Cetappareilrespecte les exigences de 10 g extrémité SAR FCC et ISED lorsquel’appareilestutilisélors de la séparation de 0 mm. ® hc 3 2016/06 CUSTOMER SUPPORT: 866.427.2999 / WWW.IDATASTART.COM
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Create Date : 2016:06:15 16:18:35-04:00 Creator : Adobe InDesign CC 2015 (Macintosh) Modify Date : 2016:06:20 13:22:18+08:00 XMP Toolkit : Adobe XMP Core 5.6-c111 79.158366, 2015/09/25-01:12:00 Metadata Date : 2016:06:20 13:22:18+08:00 Creator Tool : Adobe InDesign CC 2015 (Macintosh) Thumbnail Width : 256 Thumbnail Height : 256 Thumbnail Format : JPEG Thumbnail Image : (Binary data 15106 bytes, use -b option to extract) Instance ID : uuid:ba3b2162-2fa3-4ba9-8c0c-d731b92327ff Original Document ID : xmp.did:BB11186F4C206811822A94D671965F64 Document ID : xmp.id:c4036672-9eaf-4b4d-b430-0f0839423499 Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:cf0d5cfa-7f21-4910-8e85-afc2a7caa5f8 Derived From Document ID : xmp.did:98982a48-f8ad-4a02-9bf1-35014c2c25f0 Derived From Original Document ID: xmp.did:BB11186F4C206811822A94D671965F64 Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CC 2015 (Macintosh) History Changed : / History When : 2016:06:15 16:18:35-04:00 Format : application/pdf Producer : Adobe PDF Library 15.0 Trapped : False N Pages : 1 Has Visible Transparency : False Has Visible Overprint : True Max Page Size W : 141.816667 Max Page Size H : 141.816667 Max Page Size Unit : Millimeters Font Name : DINPro-Light Font Family : DINPro Font Face : Light Font Type : Open Type Font Version : Version 7.460;PS 7.046;hotconv 1.0.38 Font Composite : False Font File Name : DINPro-Light_0.otf Plate Names : Cyan, Magenta, Yellow, Black Swatch Groups Group Name : 默认色板组 Swatch Groups Group Type : 0 Page Count : 17EXIF Metadata provided by EXIF.tools