Avantree Technology BTHS-063 Bluetooth Headset User Manual
Avantree Technology Co., Ltd. Bluetooth Headset
User manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3942826 |
| Application ID | RSoYD/7AfFUNgV6ch94QZg== |
| Document Description | User manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 34.99kB (437402 bits) |
| Date Submitted | 2018-07-30 00:00:00 |
| Date Available | 2018-07-30 00:00:00 |
| Creation Date | 2018-02-08 17:27:34 |
| Producing Software | Microsoft? Office Word 2007 |
| Document Lastmod | 2018-07-30 09:23:53 |
| Document Title | User manual |
| Document Creator | Microsoft? Office Word 2007 |
| Document Author: | zhengl |
User’s Manual Model No: BTHS-063 Important safety instruction If used in the correct method, this design and production of this product can ensure your personal safety completely. However, any inappropriate use may lead to potential risk and danger of electric shock or fire hazard. Please read all the safety instructions before installing and using the product. In particular, attention shall be given to the following information: 1. It needs to be stored or used in the ambient temperature. 2. It shall not be placed in water or wet locations. 3. It can’t be disposed randomly for it may cause environmental pollution. 4. Without approval, It shall not be disassembled or repaired. 5. The built-in lithium battery can’t be disposed in the fire or other places to prevent causing fire hazards. 6. It shall be cleaned with dry cloth. 7. Whenever there is damage, it needs to be repaired by professional personnel. Charging the battery Fully charge the battery for about 3.5 hours before using the battery for the first time. 1. Plug the smaller end of USB charging cable into the Micro-USB interface of the connector. 2. Next, plug the other end of USB charging cable into other power charging devices or a computer with the power on. Status LED indicator Low battery Charging When power is less than 10%, the battery voltage will lower 3.3V, then there will be a voice prompt “dududu”, while the RED LED flashes twice per second---this alarm occurs every two minutes. when the voltage is lower 3.1V,the earphone will shut down automatically The red light solid on. Fully charged The red indicator will go out . Package content 1. Wireless headphone 2. Micro USB charging cable 3. 3.5mm audio cable 4. Quick user guide 5. PU bag Earphone indicator 1.LED Charging indicator 2.Charging Port 3.Volume-/Previous Track 4. Volume+/Next Track 5. LED Indicator 6.Power Button 7．AUX Port 8.MicroPhone Product feature Pairing name Li-battery capability Talking time Playing time Charging time Charger mode Straight-line distance Operation instructions Operation instructions function Key operation power on Power off Pairing B036 400 mAh 20hours 20 hours 3.5 hours Micro USB 5V/1A ≥10m description At Power off state, press power button for 3s, there is voice prompt “Dudududu". Loose the button, it will go into pairing state automatically Long press if it’s first device pairing; if the Bluetooth power button devices information existed before, it will go for 3s into standby state directly (headset re-pairs automatically in 3 minutes). it will power off if 10minutes no connection at standby state. Long Press At Power on state, press power button for 3s, power button there is voice prompt “dudududu" for 4s At Power off state, long press power button for Press power 5s, and it will go into pairing state while there is button for a voice prompt "dududu". At the same time the 5s headphone will be detected by other device, but if it’s not connected within 3 minutes, the LED status Blue LED light on for 2s, then it flash in an alternating pattern (200mS) Red LED light on 2s and then go off Red and blue LED flash alternately headphone will go into standby status. connection N/A status Re-pairing Click power Automaticall button Disconnect( automaticall y) Disconnect Play Pause Volume up Volume down Next Track Previous Track Answer call On call Reject call Blue LED flash There have voice prompt “Di”when Bluetooth twice every 5s pairing successfully Blue LED Click power button at standby station, the flashes in an headphone will enter into the repairing list 200ms interval If the phone disconnects automatically, there is Blue LED no prompt, the headphone to into standby flashes in an status . 200ms interval When the distance is out of range, the headphone will go into re-pair status in Blue LED 3minutes; it will go into standby status in 10 flashes in an minutes no connection ; also it will closed 200ms interval automatically if no connection after 10 minutes. Blue LED Short press Short press power button can replay the media Flashes twice power button while the headphone is in pause status every 5sec Blue LED Flesh Short press Short press power button can pause the twice every power button media while the headphone is in play status 5sec Short press Volume+ can increase the volume Blue LED Flesh Short press level while on music playing mode or talk twice every Volume+(15 mode, there will hear "beep" while the volume 5sec Level ) is to Max Short press Volume- can decrease the volume short press Blue LED Flesh level while on music playing mode or talk Volume-"(15 twice every mode, there will hear "Di" at min volume while Level ) 5sec the volume is to Min Blue LED Flesh Long Press Long press Volume+ to go to next song twice every Volume+ 5sec Blue LED Flesh Long Press Long press Volume- to go to next song twice every Volume5sec RED LED flash Short press power button can answer a call fast in an Short press while there is a call incoming; again a short alternating power button press of power key can end a call pattern (200mS) Blue LED light N/A N/A will be always on Long press Press and hold power button for approximately power button 2s can reject a call while there is a call for 2s incoming Short Press Volume+/Short press power button Short Press both Volume+/- at the same time when the device is connected Short Press the power button can end a call while the call in progress Redial last number Double click power button RED LED flash in an Double click power button can do redial last fast alternating number pattern (200mS) Clear pairing list Long Press Volume+/- 5s At the power on status, Long Press button RED and Volume+/- for 5s, the headphone will clear up BLUE LED light the pairing list and enter into pairing mode on 2s Siri End call Press button Press both Volume+ & power button at the Volume+ & same time, the hardware will reset power button Mic Mute on Long press Long press Volume-for 3s at call status, the call Volumeheadphone will go into/out mute When in charging, the red LED will be always on; once the energy is full,it will go Charging off When the Audio cable is plug in, the headphone will play music in line-in Line in mode(suggestion: pls disconnect bluetooth manually, or the music quality will be affected) When power is less than 10%, the battery voltage will lower 3.3V, then there will be a voice prompt “dududu”, while the RED LED flashes twice per second--this low battery alarm occurs every 1minutes. when the voltage is lower 3.1V,the earphone will shut down automatically Hardware Restoration Pairing the headphones with a computer 1.Before pairing the headphone with your computer, please make sure your computer or laptop can support bluetooth function. If not, you must purchase a bluetooth adapter (preferably version 2.1 or above). 2. Insert the bluetooth adapter to the computer, and make sure the bluetooth function of the computer is already activated. 3. Press the power button about 5s when the headphone is at power off status. It will go into paring mode when the blue and red LED light flash alternately, while you can also hear a prompt 4. Open the bluetooth software and choose to search the bluetooth device, and after few seconds, the names of bluetooth device will list out. 6. Click the pairing name “B036”to pair, when there is a prompt “beep”, this means your headphone is paired successfully . FCC Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1) Reorient or relocate the receiving antenna. 2) Increase the separation between the equipment and receiver. 3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4) Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.7 Linearized : No Author : zhengl Create Date : 2018:02:08 17:27:34+08:00 Modify Date : 2018:07:30 09:23:53+08:00 Has XFA : No Language : zh-CN XMP Toolkit : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03 Format : application/pdf Creator : zhengl Creator Tool : Microsoft? Office Word 2007 Metadata Date : 2018:07:30 09:23:53+08:00 Producer : Microsoft? Office Word 2007 Document ID : uuid:d81f2d0f-7f37-47ed-88d9-c84ca6388623 Instance ID : uuid:ede14bd0-ba75-498e-ae90-10d1a43175fb Page Count : 6EXIF Metadata provided by EXIF.tools