Axesstel AX240 CDMA Fixed Wireless Terminal With Smart Security Alert User Manual
Axesstel Inc CDMA Fixed Wireless Terminal With Smart Security Alert
Axesstel >
User Manual
Important Notice Due to the nature of wireless communications, transmission and reception of data can never be guaranteed. Data may be delayed, corrupted (i.e. have errors) or be totally lost. Although significant delays or losses of data are rare when wireless devices are used in a normal manner with a well-constructed network, the device should not be used in situations where failure to transmit or receive data could result in damage of any kind to the user or any other party, including but not limited to personal injury, death or loss of property. Axesstel accepts no responsibility for damages of any kind resulting from delays or errors in data transmitted or received using the Axessteldevice or for failure of the Axesstel device to transmit or receive such data. Safety Precautions Only use the supplied power adaptor, and do not use the power adaptor in temperatures over 40 C, and only use in a dry location Only use 9V batteries in the main unit and the motion sensors, as there is a risk of explosion if an incorrect battery type is used Please dispose of any used 9V batteries at a proper facility Do not operate the device: In areas where blasting is in progress Where explosive atmospheres may be present Near medical equipment Near life support equipment or any equipment that may be susceptible to any form of radio interference. In such areas, the device MUST BE POWERED OFF. The Axesstel device can transmit signals that could interfere with this equipment. AXESSTEL ALERT PRODUCTS CONSUMER WARRANTY AND LIMITATION OF LIABILITY THE AXESSTEL ALERT PRODUCT THAT YOU HAVE PURCHASED, WHEN PROPERLY INSTALLED, CAN BE USED TO DETECT MOTION IN A SPECIFIED AREA AND PROVIDE AN ALERT TO TELEPHONES OR PERSONAL DIGITAL ASSISTANTS THAT YOU SPECIFY. THE PRODUCT IS DESIGNED SOLELY TO PROVIDE AN ALERT. IT DOES NOT PROVIDE SECURITY, OR PREVENT INTRUSION, THEFT OR CRIME. THE PRODUCT IS NOT A SECURITY SERVICE, ALERTS ARE SENT ONLY TO THE DEVICES YOU SPECIFY. THEY ARE NOT MONITORED BY AXESSTEL, THE TELEPHONE COMPANY, LAW ENFORCEMENT OR OTHER AGENCIES. ALERTS ARE SENT OVER THE PUBLIC WIRELESS TELEPHONE NETWORK. INTERRUPTION OF TELEPHONE SERVICE WILL PREVENT TRANSMISSION OF ALERTS. LIMITED WARRANTY.FOR PERIOD OF [APPLICABLE WARRANTY PERIOD],AXESSTEL WARRANTS THAT THE ALERT PRODUCT SHALL (I) BE FREE FROM DEFECTS IN DESIGN, MATERIALS OR WORKMANSHIP, (II) CONFORM TO ITS PRODUCT SPECIFICATIONS AND (III) BE COMPLIANT WITH ITS WIRELESS COMMUNICATION STANDARD (CDMA 1X, EVDO, GSM, GPRS AND EDGE, AS APPLICABLE). FOR ANY PRODUCTS THAT FAIL TO MEET THE FOREGOING WARRANTY, AXESSTEL, SHALL REPAIR OR REPLACE SUCH PRODUCTS, IN ITS DISCRETION, SO THAT ANY DEFECTIVE PRODUCT OR ANY REPLACEMENT PRODUCT SHALL CONFORM TO THE WARRANTY. IF AXESSTEL CANNOT CURE ANY DEFECT ON COMMERCIALLY REASONABLE TERMS, AXESSTEL SHALL REFUND THE VALUE OF THE NON-CONFORMING PRODUCT WITHIN FORTY- FIVE (45) DAYS.EXCEPT FOR THE FOREGOING WARRANTY, AXESSTEL MAKES NO WARRANTIES, EXPRESS OR IMPLIED, WITH RESPECT TO THE ALERT PRODUCT, AND SPECIFICALLY DISCLAIMS ANY WARRANTIES INCLUDING BUT NOT LIMITED TO ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR AGAINST INFRINGEMENT, OR ANY EXPRESS OR IMPLIED WARRANTY ARISING OUT OF TRADE USAGE OR OUT OF A COURSE OF DEALING OR COURSE OF PERFORMANCE AXESSTEL DOES NOT REPRESENT OR WARRANT THAT THE PRODUCT WILL OPERATE ERROR FREE, OR THAT THE PRODUCT WILL NOT BE DISABLED, COMPRISED OR CIRCUMVENTED (BY DISABLING TELEPHONE SERVICE OR IN SOME OTHER WAY). AXESSTEL DOES NOT WARRANT THAT THE PRODUCT WILL DETECT OR PREVENT ALL INTRUSION, LOSS OF PROPERTY OR PERSONAL INJURY OR BURGLARY, HOLD-UP, FIRE, OR MEDICAL PROBLEM; OR THAT THE PRODUCT WILL IN ALL CASES PROVIDE THE PROTECTION FOR WHICH IT IS INTENDED. LIMITATION OF LIABILITY. AXESSTEL NOT BE LIABLE TO YOU UNDER ANY CIRCUMSTANCE FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES, ARISING OUT OF THE USE OR INABILITY TO USE, ANY OF THE ALERT PRODUCTS OR COMPONENTS. AXESSTEL WILL NOT BE RESPONSIBLE FOR ANY LOSS OF PROPERTY, DAMAGE TO PROPERTY, PERSONAL INJURY, DEATH OR OTHER INCIDENTAL DAMAGES, HOWEVER CAUSED, ARISING OUT OF THE USE OR INABILITY TO USE, ANY OF THE ALERT PRODUCTS OR COMPONENTS. ANY LIABILITY OF AXESSTEL TO YOU, AND YOUR SOLE AND EXCLUSIVE REMEDY, FOR ANY CLAIM ARISING OUT OF THE USE OR PURCHASE OF THE PRODUCT (WHETHER IN CONTRACT, TORT, OR OTHERWISE) WILL NOT EXCEED THE PURCHASE PRICE PAID FOR THE PRODUCT WHICH IS THE SUBJECT OF SUCH CLAIM OR CAUSE OF ACTION. NOT INSURANCE. AXESSTEL IS NOT AN INSURER AND IS NOT RESPONSIBLE FOR ACTS OR OMISSIONS OF OTHERS OR FOR EVENTS BEYOND ITS CONTROL. THE PURCHASE PRICE FOR THE PRODUCT HAS NO RELATIONSHIP TO THE VALUE, IN WHOLE OR IN ANY PART, ANY LOSS, DAMAGE, INJURY OR DEATH WHICH MIGHT RESULT TO YOU OR YOUR PROPERTY FROM ANY HAZARD OR EVENT OR CONSEQUENCE WHICH THE PRODUCT IS INTENDED TO DETECT. YOU HAVE THE SOLE RESPONSIBILITY TO OBTAIN WHATEVER INSURANCE YOU WANT TO HAVE IN ORDER TO COVER RISK, LOSSES, DAMAGES, INJURIES, DEATH AND OTHER EFFECTS OF BURGLARY, FIRE, PHYSICAL DANGERS OR MEDICAL PROBLEMS AFFECTING, YOU, YOUR FAMILY OR ANY OTHER PERSONS WHO MAY BE IN OR NEAR YOUR LOCATION. YOU WILL LOOK SOLELY TO THE PROCEEDS OF SUCH INSURANCE FOR ANY LOSS, LIABILITY, DAMAGE OR CLAIM. USE AT OWN RISK. YOU ACCEPT THE ENTIRE RISK OF THE USE OF THE PRODUCT. YOU HEREBY AGREE TO RELEASE, DEFEND, INDEMNIFY AND HOLD AXESSTEL HARMLESS FROM AND AGAINST CLAIM OR LIABILITY FOR ANY RISK, LOSS, PROPERTY DAMAGE, PERSONAL INJURY, DEATH AND OTHER EFFECTS MENTIONED ABOVE AT YOUR SOLE COST AND EXPENSE INCLUDING ATTORNEY’S FEES. Table of Contents Important Notice ..................................................................................................... 1 Introduction .......................................................................................................... 11 Product Overview ................................................................................................. 11 1. Features ........................................................................................................ 12 2. Benefits ......................................................................................................... 14 Using your Axesstel Home Alert .......................................................................... 16 1. Package Contents ........................................................................................ 16 2. Knowing your Main Unit ................................................................................ 16 2.1 LEDs .................................................................................................. 19 2.2 Battery Installation into Base Unit ...................................................... 23 2.3 Battery Installation into Alert Panel .................................................... 24 2.4 Battery Installation into Motion Sensor .............................................. 24 2.5 Connecting the Power Adaptor into the Base Unit ............................ 25 2.6 Connecting the Power Adaptor into Alert Panel ................................ 26 2.7 Setting Up the Base Unit.................................................................... 27 2.8 Placement of the Base Unit ............................................................... 28 2.9 Placement of Alert Panel ................................................................... 28 2.10 Placement of Motion Sensor .......................................................... 28 3. Using your 200 Series as a Landline Replacement Phone .......................... 29 3.1 Power On/Off ..................................................................................... 29 3.2 Activation............................................................................................ 29 3.3 Setting Up Your Voicemail ................................................................. 30 3.4 Making Calls ...................................................................................... 30 3.5 Answering Calls ................................................................................. 31 3.6 Default Reset ..................................................................................... 31 3.7 Factory Reset ..................................................................................... 31 3.8 TTY/TDD Mode Setting...................................................................... 32 3.9 Caller ID ............................................................................................. 33 3.10 Setting Caller ID Mode ................................................................... 33 3.11 Call Waiting .................................................................................... 33 3.12 Three-Way Calling .......................................................................... 34 3.13 E911 Information ............................................................................ 34 4. Using your 200 Series as an Alert System ................................................... 35 4.1 Programming Mode ........................................................................... 35 4.1.1 Changing the Password.............................................................. 36 4.1.2 Adding SMS Numbers ................................................................ 38 4.1.3 Removing SMS Numbers ........................................................... 40 4.1.4 Adding Call Numbers .................................................................. 40 4.1.5 Removing Call Numbers ............................................................. 43 4.1.6 Adding Sensors .......................................................................... 43 4.1.7 Pet Immunity ............................................................................... 46 4.1.8 Removing Sensors ..................................................................... 46 4.1.9 Adding the Key Fob .................................................................... 47 4.1.10 Adding the Panic Key Fob .......................................................... 48 4.1.11 Set Entry Mode ........................................................................... 48 4.1.12 Set Exit Mode ............................................................................. 49 4.1.13 Factory Reset ............................................................................. 50 4.1.14 Test Mode 1 – Call ...................................................................... 51 4.1.15 Test Mode 2 – SMS .................................................................... 51 4.2 Armed Mode ...................................................................................... 52 4.2.1 Armed Away ............................................................................... 52 4.2.2 Armed Away Silent ..................................................................... 53 4.2.3 Armed Stay ................................................................................. 53 4.2.4 Armed Stay Silent ....................................................................... 55 4.2.5 Remote Arming via Key Fob ....................................................... 56 4.2.6 Remote Arming via Smartphone App ......................................... 56 4.2.7 Continued Arming ....................................................................... 56 4.3 Disarmed Mode .................................................................................. 56 4.3.1 Disarm via Keypad ...................................................................... 57 4.3.2 Remote Disarm via Key Fob ....................................................... 57 4.3.3 Remote Disarm via Smartphone App ......................................... 57 4.4 Alarmed Mode .................................................................................... 58 4.4.1 Panic Button ............................................................................... 58 4.5 Additional Functions & Features ........................................................ 59 4.5.1 Audio Monitoring/2-Way Communication ................................... 59 4.5.2 Tamper Prevention ..................................................................... 59 4.5.3 Audible Siren .............................................................................. 59 4.5.4 Axesstel Home Alert Accessories ............................................... 60 5. AX240 Smartphone Application .................................................................... 61 5.1 AX240 App for Android ...................................................................... 61 5.2 AX240 App for iPhone ....................................................................... 62 5.3 AX240 App creating user account (Android/iOS) .............................. 62 5.4 Manage Call Numbers (Android/iOS) ................................................ 65 5.5 Manage SMS Numbers (Android/iOS) ............................................... 66 5.6 Delay Time (Entry/Exit ) ..................................................................... 67 5.7 Remote Arming/Disarming ................................................................. 69 5.8 Account Info/Device Status (Android/iOS) ......................................... 70 5.9 Event Log ........................................................................................... 72 Z-Wave ................................................................................................................. 73 Operating Specifications ...................................................................................... 79 1. Base Unit AX240 .......................................................................................... 79 2. Alert Panel AZ900......................................................................................... 80 3. Motion Sensor AZ100 ................................................................................... 81 Safety Information ................................................................................................ 82 10 Introduction This user manual will help you place, configure and use your AX240 Alert System. Product Overview The AX240 Axesstel Home Alert is a fixed cellular terminal with a wireless alert system. As a terminal, the AX240 has an RJ-11 interface for POTS phones to make and receive phone calls as done through a landline. As a home alert, a built-in cellular modem can send an SMS or place a phone call to a series of pre-assigned phone numbers when a sensor is triggered. Up to 8 contacts can be notified of the alert. The arming and disarming can be triggered by keypad input or by sending an SMS. Smartphone applications are available on ‘Google Play’ for Android and ‘App Store’ for iOS. The AX240 Axesstel Home Alert has LED indicators to represent the status of the product and sensors. It is easy to set up and configure in a few simple steps. The system is expandable to connect up to 200 sensors utilizing Z-Wave protocol. The AX240 is powered by an AC adapter with a 1600mAh rechargeable battery backup to provide continued functionality in the event of a power outage. This self-monitoring alert system can provide peace of mind and security without the need for an expensive security contract. 11 Some features described in this manual may not be supported by your service provider or may not be available with your network account. For details of the services and accounts available, contact your service provider. 1. Features • • • • • • • • • • • • 12 Android and iOS Applications for AX240 Management 800MHz/1900MHz CDMA2000 1x-Advanced Z-Wave Short Range Wireless Protocol Call Alerting Numbers - Stores 5 pre-assigned numbers SMS Alerting Numbers - Stores 3 pre-assigned number Remote Arm/Disarm Capabilities via Smartphone application 10 Multiple LED Indicators (Alert Panel) - Power, Battery, CDMA, Setting/Register, Active, Zone Status Indicator 1 – 4, Account OMA-DM HFA or OTASP Activation Standard Telephone Keypad with Tactile Feel Audible Siren for Alert Trigger Audible Beeper and LED Indicationfor Programming Configuration Panic Button for Emergency Situations • • • • • • • • • • • • • • • • Event History Log Silent Alarm Capability Low Battery Warning LED for Sensors on Base Unit Tamper Prevention on Alert Panel, Motion Sensor, and Window/Door Sensors Z-Wave Capabilities Include Motion Sensors, Door/Window Sensors, Keyfob, and Others Configure up to 200 Sensors/Motion Detectors Armed Away, Armed Home, and Disarm Modes 4 Alert Function Keys – Arm/Disarm, Stay, Panic, Function Store/Manage User Defined 4-Digit Passcodes Delayed Entry/Exit Mode 5 Multiple LED Indicators (Base Unit) – Power, Battery, Voicemail Waiting Indicator, Mode, CDMA 2 RJ-11 Ports (Bridged) to Connect to POTS Phones Dial Tone and DTMF Generation AGPS for E911 Service Support Call Waiting, Call Forwarding, Three-Way Calling, and Hook Flash FUMO Support 13 • • • • 2. Automatic Sender Caller ID Built-in Speaker and Microphone to Monitor Surroundings Rechargeable 1600mAh Li-Ion Backup Battery (Base Unit) USB Diagnostic Port for Firmware Upgrades Benefits Wireless Alert Notification - SMS/Call Alerts if the Motion Sensor is Triggered The AX240 Axesstel Home Alert has a built-in 1x-Advanced cellular modem that can notify up to 8 friends and neighbors via call and SMS when motion is detected to increase chances of a close-by responder. Landline Phone Replacement The AX240 has an RJ-11 interface for POTS phones to make and receive phone calls as done through a landline. Current phone numbers can be maintained and monthly costs can be decreased. 14 Emergency Backup Battery An AC adaptor with a 1600mAh backup battery provides the base unit with continued functionality in the event of a power outage. The alert panel contains an AC adaptor and a 9V backup battery. Remote Control Convenience The arming and disarming of the AX240 Alert System can be triggered by keypad input or by sending a remote SMS from one of your registered numbers. A smartphone app may also be used from your Android or iOS smartphone. Affordable, Easy to Setup, Configure, and Use Setup and configuration of the AX240 Axesstel Home Alert is accomplished simply. The base unit has 5 LED indicators and the alert panel has 10 LED indicators to represent the product status. This reasonably priced system can be configured for use with up to 200 sensors or motion detectors. All the accessories in the box have been pre-associated with the main unit and are ready to be used. 15 Using your Axesstel Home Alert 1. Package Contents Standard contents may vary from carrier to carrier. The items listed below may be added to depending upon carrier preferences. AX240 Base Unit AZ900 Alert Panel Motion Sensor Power Adaptors Mounting Kits User Manual/Quick Start Guide 2. Knowing your Main Unit Your Axesstel Home Alert is designed to be wall mounted, or it can simply be placed on a shelf. All the LEDs are easily visible while the power cord will connect at the back. See figure 1 for a depiction of the device. 16 AX240 Base Unit Figure 1 17 AZ900 Alert Panel Figure 2 18 2.1 LEDs The AX240 base unit has 5 LEDs. The functionality of the LEDs is found in the table below. Base Unit LED description LED Color Function Device is powered on Power Green The device is powered off OFF Battery is sole source, power above Green mid-level AC is sole source, battery charging Blink Green Battery Battery is sole source, voltage low Red AC is sole source, no battery Blink Red Camped on network Green CDMA No CDMA coverage Red Incoming call Green Off hook Mode Red On hook OFF Voicemail in the system Red VoicemailWaitingIndicator No new voicemail OFF 19 E911 Call All LEDs Blinking All LEDs blink during emergency call The AZ900alert panel has 10 LEDs. The functionality of the LEDs is found in the table below. Alert Panel LED description LED Color Function Device is powered on Power Green The device is powered off OFF Battery is good/ powered by battery Blink Green Battery is low/ powered by battery Battery Red No battery in use OFF Good signal coverage Green Mid-signal coverage Blink Green Signal (CDMA/GSM) Red Lowsignal coverage No coverage OFF In setting status Green Setting /Register In registration status, push button in sensor to add Blink Green 20 Active (On) Zone1 Zone2 Zone3 Zone4 Red OFF Green Red OFF Blink Red Green Red OFF Blink Red Green Red OFF Blink Red Green Red OFF Blink Red Device is armed Device is disarmed Sensor is Armed Sensor Alarm detected Sensor is Disarmed Sensor Low battery warning Sensor is Armed Sensor Alarm detected Sensor is Disarmed Sensor Low battery warning Sensor is Armed Sensor Alarm detected Sensor is Disarmed Sensor Low battery warning Sensor is Armed Sensor Alarm detected Sensor is Disarmed Sensor Low battery warning 21 Account (Bill) Programming Mode OFF Green Blink Red Programming Mode Exit Blink Green Programming Success Programming Failure 22 Blink Red Optional use by Network When in Programming Mode the Power, Battery, Signal and Setting/Register LEDs will be green When in Programming Mode after a key is pressed, if 5 seconds elapse before another key is pressed all 4 Zone LEDs will blink red 3 times and the programming sequence will need to begin anew. If 30 seconds elapse before another key is pressed, the Axesstel Home Alert will exit the programming mode and all LEDs will return to their normal state When in Programming Mode successful programming will result in all 4 Zone LEDs blinking green 1 time When in Programming Mode failed programming will result in all 4 Zone LEDs blinking red 3 times 2.2 Battery Installation into Base Unit Your AX240 base unit provides battery backup support with a 1600mAh rechargeable LiIon battery. Please see figure3 below to install the battery. Figure 3 23 2.3 Battery Installation into Alert Panel Your AZ900 alert panel provides battery backup support. Please see figure 4 below to install the 9V battery. 2.4 Battery Installation into Motion Sensor To install the battery into the Motion Sensor please see figure4 below. Figure 4 24 2.5 Connecting the Power Adaptorinto the Base Unit To connect the power adaptor to the base unit,please see figure 5 below. Figure 5 25 2.6 Connecting the Power Adaptorinto Alert Panel To connect the power adaptor to the alert panel,please see figure 6 below. Figure 6 26 2.7 Setting Up the Base Unit Connect the antenna by screwing it into the connector on the back of the AX240 base unit. Connect a wired or cordless telephone to the base unit sing the supplied RJ-11 cord. Plug the power adaptor cable into the base unit. Plug the power adaptor into an AC power wall outlet. See figure 7 below. Figure 7 27 Note: Use only wired or cordless telephones that conform to FCC part 68 requirements. Non-compliant telephones may not work properly. WARNING:Do not connect this device to your telephone wall outlet. This configuration is not supported unless you have taken steps to disconnect existing landline wiring coming into your home or office. 2.8 Placement of the Base Unit The base unit should be placed on any convenient desktop or table top in the house. 2.9 Placement of Alert Panel The keypad can be placed at any convenient access point in the house. 2.10 Placement of Motion Sensor The motion sensor should be placed on shelves or walls and can detect motion within 12 meters, great for rooms with lots of windows. 28 3. Using your 200 Series as a Landline Replacement Phone 3.1 Power On/Off The power button is located on the top of the AX240. Plug the power adapter into an AC power wall outlet.Plug the power adapter into the power connector on the back of the device. Push the power button on top of the device for several seconds, then release. The green light will illuminate. Turn the AX240 off by pushing the power button on top of device for several seconds, then release. The green light will turn off. 3.2 Activation To activate your AX240 using Over the Air Service Provisioning (if supported by your carrier) turn on your device.The device will begin its initiation process and start to acquire the network. Wait 2 minutes to complete. From your connected phone dial *228 and follow the voice prompts to complete the activation. NOTE:Check with your service provider before activation as your device may already be activated. 29 3.3 Setting Up Your Voicemail You should set up your voicemail and personal greeting as soon as your device is activated. Always use a password to protect against unauthorized access. Please check with your service provider for the voicemail access number. Your device automatically transfers all unanswered calls to your voicemail, even if your device is in use or turned off. Dial your voicemail number (the phone number assigned to your phone). Follow the prompts to create your password, record your name announcement, and record your greeting. 3.4 Making Calls Check if the device is turned on.Lift the handset on any connected phone. You should hear a dial tone.Dial a number as you usually would. Wait for about 3 seconds while your device connects with the number you dialed. NOTE:You can dial phone numbers with up to 32 digits including 30 and 3.5 Answering Calls When connected to your AX240, your phone will ring exactly as if it were connected to a landline. Lift the handset on any connected phone to answer a call. 3.6 Default Reset If you want to clear any changes you have made to your AX240’s settings and reset it to the default settings lift the handset on any connected phone. Press: Enter the four-digit lock code (default is “1234”). Press to reset. You will hear two short tones if successful or four short tones if the reset was unsuccessful. 3.7 Factory Reset To reset your device to factory conditionlift the handset on any connected phone. Press: 31 Enter the six-digit SPC default code (the default code is “000000”). You will hear two short tones if successful and your device will reset or four short tones if the reset was unsuccessful. 3.8 TTY/TDD Mode Setting Configure your device for TTY use. The default setting is OFF. Lift the handset on any connected TTY/TDD phone and choose one of the following options: Press Press Press Press 32 for TTY Full Mode. for TTY Talk Mode. for TTY Hear Mode. to turn TTY off. 3.9 Caller ID Caller ID allows people to identify a caller before answering the phone by displaying the number of the incoming call. If you do not want your number displayed when you make a call, follow these steps. Press . Enter your phone number. 3.10 Setting Caller ID Mode If the phone you have connected to your AX240 has an LCD display, the caller’s number will appear by default. To change this setting lift the handset of any connected phone. Press Press to disable the Caller ID feature. to re-enable the Caller ID. 3.11 Call Waiting When you’re on a call, Call Waiting alerts you to incoming calls. When you hear a beep from the receiver on any connected phone during a call, it means a second caller is trying 33 to connect. To use call waiting press the hook or the flash button (if present) to answer the second call. Press the hook or the flash button again to return to the first call. 3.12 Three-Way Calling With Three-Way Calling you can talk to two people at the same time. When using this feature, the normal airtime rates will be charged for each of the two calls. To use ThreeWay Calling call the first party, place a second call by pressing the hook or the flash button (if present), enter the second party’s number, and press the hook or flash button again to dial the number. When you are connected to the second party, press the hook or flash button to start the three-way call. 3.13 E911 Information Your device features an embedded Global Positioning System (GPS) chip necessary for utilizing E911 emergency location services where available. During the emergency call, all the LEDs on the AX240 will blink and your location can then be determined by the 911 operator. IMPORTANT: Always report your location to the 911 operator when placing an emergency call. Some designated emergency call takers, known as Public Safety 34 Answering Points (PSAPs) may not be equipped to receive GPS location information from your device. 4. Using your 200 Series as an Alert System Now that the battery is installed and the power adaptor is connected you are ready to use some of the more advanced features of the Axesstel Home Alert. Your 100 Series device has four operational modes. They are programming mode, armed mode, disarmed mode, and alarmed mode. The following sections will describe the device’s functionality within each of these four modes. 4.1 Programming Mode The programming mode is used for setting the parameters of the Axesstel Home Alert such as changing the password, adding/deleting SMS/Call numbers, setting entry/exit delay, and adding/removing motion sensors and other accessories. The programming mode is also used to restore the device to factory settings. To access the programming mode please use your keypad and enter the following: Func KeypasswordFunc Key 35 Please note: All functions listed in this section of the user’s guide require that you be in the programming mode to perform them. When you are in the programming mode the Power, Battery, Signal, and Setting/Register LEDs will all be solid green. When in the programming mode and a sequencehas been initiated a 5 second timer will be kept. After a key is pressed, if 5 seconds elapse before another key is pressed all 4 Zone LEDs will blink red 3 times and the programming sequence will need to begin anew. If 30 seconds elapse before another key is pressed, the Axesstel Home Alert will exit the programming mode. When programming is complete to exit the programming mode use your keypad and enter the following or simply wait for 30 seconds to elapse. All LEDs should return to their normal state. Func KeyFunc Key 4.1.1 Changing the Password To change the default password use your keypad to enter the following: Func Key00Func Keynew passwordnew passwordFunc Key 36 Please note: It is advisable to change your password as soon as you connect the Axesstel Home Alert. *Example: The default password is 1234. If you want to change your password to 4897, then you would enter the following: Func 1 Func 0 Func 4 Func Func to enter the programming mode, then to change the password. 37 4.1.2 Adding SMS Numbers When a motion sensoror other accessory is triggered in any zone, you can choose to send an SMS to up to 3 numbers. SMS numbers can be added into your Axesstel Home Alertin two different manners. A phone call from the desired number will register that number in the designated slot by following these instructions. You must be in the programming mode to perform this function. Add SMS #1 Add SMS #2 Add SMS #3 Func Key31Func Key00Func Key Func Key32Func Key00Func Key Func Key33Func Key00Func Key Then call from phone number Then call from phone number Then call from phone number As an alternative the SMS numbers can be programmed entirely via the keypad. Once in the programming mode please enter the following: Add SMS #1 Add SMS #2 Add SMS #3 38 Func Key31Func KeySMS #1SMS #1Func Key Func Key32Func KeySMS #2SMS #2Func Key Func Key33Func KeySMS #3SMS #3Func Key *Example: If you want to add phone number 123-456-7890 into the first SMS slot, then you would enter the following: Func 1 Func 3 1 to program the phone number into SMS slot #1 0 Func 1 Func to enter the programming mode, then Func Please note: You have to enter the desired number twice. The number that you entered will need to match. If the numbers entereddo not match then there will be a long beep and all 4 Zone LEDs will blink red 3 times. If the numbers match then you will hear 2 beeps and all 4 Zone LEDs will blink green 1 time. 39 4.1.3 Removing SMS Numbers To remove the SMS numbers please enter the keypad sequences below. You must be in the programming mode to perform this function. Delete All SMS #’s Delete SMS #1 Delete SMS #2 Delete SMS #3 Func Key40Func Key Func Key41Func Key Func Key42Func Key Func Key43Func Key 4.1.4 Adding Call Numbers When a motion sensoror other accessory is triggered in any zone, you can choose to make a phone call to up to 5 numbers. Call numberscan be added into your Axesstel Home Alertin two different manners. 40 A phone call from the desired number will register that number in the designated slot by following these instructions. You must be in the programming mode to perform this function. Add Call #1 Add Call #2 Add Call #3 Add Call #4 Add Call #5 Func Key51Func Key00Func Key Func Key52Func Key00Func Key Func Key53Func Key00Func Key Func Key54Func Key00Func Key Func Key55Func Key00Func Key Then call from phone number Then call from phone number Then call from phone number Then call from phone number Then call from phone number As an alternative the call numbers can be programmed entirely via the keypad. Once in the programming mode please enter the following: Add Call #1 Add Call #2 Add Call #3 Add Call #4 Add Call #5 Func Key51Func KeyCall#1Call#1Func Key Func Key52Func KeyCall #2Call #2Func Key Func Key53Func KeyCall #3Call #3Func Key Func Key54Func KeyCall #4Call #4Func Key Func Key55Func KeyCall #5Call #5Func Key 41 *Example: If you want to add phone number 123-456-7890 into the first Call slot, then you would enter the following: Func 1 Func 5 1 to program the phone number into Call slot #1 0 Func 1 Func to enter the programming mode, then Func Please note: You have to enter the desired number twice. The number that you entered will need to match. If the numbers entereddo not match then there will be a long beep and all 4 Zone LEDs will blink red 3 times. If the numbers match then you will hear 2 beeps and all 4 Zone LEDs will blink green 1 time. 42 4.1.5 Removing Call Numbers To remove the Call numbers please enter the keypad sequences below. You must be in the programming mode to perform this function. Delete All Call #’s Delete Call #1 Delete Call #2 Delete Call #3 Delete Call #4 Delete Call #5 Func Key60Func Key Func Key61Func Key Func Key62Func Key Func Key63Func Key Func Key64Func Key Func Key65Func Key 4.1.6 Adding Sensors To add motion sensors (AZ100) to the Axesstel Home Alert please follow the instructions below. Up to 200 Motion sensors and other accessories can be added across 4 zones. In the rear housing of the motion sensor, there is a small push button switch which is used for adding the sensor (inclusion) and removing (exclusion) the sensor. The following will add the AZ100 sensors (inclusion/association) to the 100 Series Axesstel Home Alert (see figure 4 below). 43 Please note: You will need to remove the motion sensor battery cover in order to register your sensor. You must be in the programming mode to perform this function. Add Sensor in Zone 1 Func Key11FuncKey Add Sensor in Zone 2 Func Key12FuncKey Add Sensor in Zone 3 Func Key13FuncKey Add Sensor in Zone 4 Func Key14FuncKey Zone 1 LED will light then press the sensor button. Zone 2 LED will light then press the sensor button. Zone 3 LED will light then press the sensor button. Zone 4 LED will light then press the sensor button. Please note:You need to press the button of the desired sensor within 30 seconds to registerit correctly. If the sensor has not been registered properly there will be a long beep and all 4 Zone LEDs will blink red 3 times. If the sensor has been registered properly then you will hear 2 beeps and all 4 Zone LEDs will blink green 1 time. To add additional sensors in your desired zone please repeat the above instructions. 44 The location of the button in the AZ100 motion sensor is depicting in figure 8. All approved Z-wave accessories will have an inclusion/exclusion button. Consult the literature provided with those accessories to properly locate the button. Figure 8 45 4.1.7 Pet Immunity The AZ100 passive infrared (PIR) motion detector can be adjusted to provide pet immunity. Remove the back cover of the PIR motion sensor (see figure 6) to adjust the range/sensitivity setting. Moving the jumper to the number 3 position will adjust for minimum sensitivity. You can also adjust the angle of the sensor slightly upwards to further minimize pet sensitivity. The sensitivity setting can be adjusted prior to or after the sensor has been registered. 4.1.8 Removing Sensors To remove/delete (exclusion) any motion sensors or other accessories please follow the instructions below. You must be in the programming mode to perform this function. Remove motion sensor or other accessory Func Key10Func Key Press the sensor button Please note: You need to press the button of the desired sensor within 30 seconds to remove (exclude) it correctly. If the procedure has not been accomplished properly 46 therewill be a long beep and all 4 Zone LEDs will blink red 3 times. If the sensor has been removed properly then you will hear 2 beeps and all 4 Zone LEDs will blink green 1 time. 4.1.9 Adding the Key Fob To add the 4-Button Key Fob (AZ300) to the Axesstel Home Alert please follow the instructions below. You must be in the programming mode to perform this function. Func Key16FuncKey Press the Arm and Panic Keys simultaneously for at least 0.5 seconds You need to press the Key Fob button within 30 seconds to registerit correctly. If the Key Fob has not been registered properly there will be a long beep and all 4 Zone LEDs will blink red 3 times. If the Key Fob has been registered properly then you will hear 2 beeps and all 4 Zone LEDs will blink green 1 time. 47 4.1.10 Adding the Panic Key Fob To add the 1-Button Panic Key Fob (AZ310) to the Axesstel Home Alert please follow the instructions below. You must be in the programming mode to perform this function. Func Key16FuncKey Press and Release the Panic Key 3 times You need to press the Panic Key Fob button within 30 seconds to registerit correctly. If the Panic Key Fob has not been registered properly there will be a long beep and all 4 Zone LEDs will blink red 3 times. If the Panic Key Fob has been registered properly then you will hear 2 beeps and all 4 Zone LEDs will blink green 1 time. 4.1.11 Set Entry Mode You can modify the entry time delay to suit your needs. This will delay a sensor from being triggered from between 0 and 45 seconds. The default entry delay is set to 30 seconds. To adjust the entry delay please follow the instructions below. You must be in the programming mode to perform this function. No Entry Delay 15 Second Delay 48 Func Key70Func Key Func Key71Func Key 30 Second Delay 45 Second Delay Func Key72Func Key Func Key73Func Key Example: If you want to set the entry delay to 15 seconds, then you would enter the following: Func 7 Func 4.1.12 Set Exit Mode You can modify the exit time delay to suit your needs. This will delay a sensor from being triggered from between 0 and 120 seconds. The default exit delay is set to 30 seconds. To adjust the exit delay please follow the instructions below. You must be in the programming mode to perform this function. No Exit Delay 30 Second Delay 60 Second Delay 90 Second Delay 120 Second Delay Func Key80Func Key Func Key81Func Key Func Key82Func Key Func Key83Func Key Func Key84Func Key 49 The setting of ‘No Exit Delay’ can only be enabled when the Axesstel Home Alert 100 Series device is armed remotely. Example: If you want to set the exit delay to 60 seconds, then you would enter the following: Func 8 Func 4.1.13 Factory Reset If your unit malfunctions or develops any form of software fault then it may be necessary to perform a factory reset. To do so, please follow the instructions below. After a factory reset is performed you will need to re-program your SMS/Call numbers and any other parameters you have changed. You must be in the programming mode to perform this function. Func Key90Func Key 50 4.1.14 Test Mode 1 – Call Test Mode 1 allows the Axesstel Home Alert to make a phone call to any phone number.Please follow the instructions below. You must be in the programming mode to perform this function. Func Key92Func Keyphone numberFunc Key 4.1.15 Test Mode 2 – SMS Test Mode 2 allows the Axesstel Home Alert to send an SMS to any phone number. Please follow the instructions below. You must be in the programming mode to perform this function. Func Key93Func Keyphone numberFunc Key 51 4.2 Armed Mode After the Axesstel Home Alert has been installed, motion sensors have been added, and the SMS/Call numbers have been programmed it can be used as an alert system. Once in armed mode any sensor that is triggered in an active zone will initiate the alerting process. There are 4 different armed modes: Armed Away, Armed Away Silent, Armed Stay, and Armed Stay Silent. 4.2.1 Armed Away In the Armed Away mode, when a sensor is triggered, the 100 Series Axesstel Home Alert will emit a high-pitched continuous siren for 4 minutes. All programmed SMS and Call numbers will be sent an alert notifying them of the alarm. Away /On To activate the ArmedAwaysimply press the Away/On Key. Away/On Key 52 Activates Armed Away Mode 4.2.2 Armed Away Silent The Armed Away Silent mode provides essentially the same functionality as the Armed Away mode except when a sensor is triggered no high-pitched siren is audible.The intruder will be unaware that the alarm has been triggered, although SMS/Calls will be sent. To activate the Armed AwaySilent simply press the #1 and Away/On Key. Away /On 1Away/On Key Activates Armed Away Silent Mode 4.2.3 Armed Stay Occasionally you may want to arm only a certain part of your house, and this can be achieved by using the Armed Stay mode. Please note:Zones one, two and three will be excluded when using the Armed Stay mode.You can activate your alarm so that any motion in zonefour will trigger the alarm, 53 but if there is any movement in zones one, two or three then the alarm will not be triggered. In the Armed Stay mode, when a sensor is triggered, the 100 Series Axesstel Home Alert will emit a high-pitched continuous siren for 4 minutes. All programmed SMS and Call numbers will be sent an alert notifying them of the alarm. Stay /On To activate the Armed Staysimply press the Stay/On Key. Stay/On Key 54 Activates Armed Stay Mode 4.2.4 Armed Stay Silent The Armed Stay Silent mode provides essentially the same functionality as the Armed Away mode except when a sensor is triggered no high-pitched siren is audible.The intruder will be unaware that the alarm has been triggered, although SMS/Calls will be sent. Please note:Zones one, two and three will be excluded when using the Armed Stay Silent mode. You can activate your alarm so that any motion in zonefour will trigger the alarm, but if there is any movement in zones one, two or three then the alarm will not be triggered. To activate the Armed StaySilent simply press the #1 and Stay/On Key. 1Stay/On Key Stay /On Activates Armed Stay Silent Mode 55 4.2.5 Remote Arming via Key Fob You can also arm the Axesstel Home Alert remotely via the Key Fob. Please refer to the instructions included with your Key Fob. 4.2.6 Remote Arming via Smartphone App You can also arm the Axesstel Home Alert remotely via the Smartphone (Android/iOS) App. Please refer to App section in this user’s manual. 4.2.7 Continued Arming If a sensor has been triggered and after 4 minutes the device has not been disarmed, it will automatically re-arm. At this point another SMS will be sent to the programmed SMS numbers (no Calls are made in this instance). This is the case in all 4 armed modes. 4.3 Disarmed Mode When you return home or wherever you have your Axesstel Home Alert set up you will want to place it in a disarmed state so no alert notifications are sent. The amount of time you have to disarm your device is dependent on the entry time delay previously programmed.There are multiple ways the Axesstel Home Alert can be placed in the disarmed mode. 56 4.3.1 Disarm via Keypad To disarm the Axesstel Home Alert using the keypad simply enter your password. Password 4.3.2 Remote Disarm via Key Fob You can also arm the Axesstel Home Alert remotely via the Key Fob. Please refer to the instructions included with your Key Fob. 4.3.3 Remote Disarm via Smartphone App You can also disarm the Axesstel Home Alert remotely via the Smartphone (Android/iOS) App. Please refer to App section in this user’s manual. 57 4.4 Alarmed Mode The alarmed mode isentered when a sensor is triggered and alerts have been sent. When one of the disarm procedures above is followed the device will be in disarmed mode, however, the alerts will have already been issued. If no disarm command is received within 4 minutes the Axesstel Home Alert will re-arm as described in the continued arming section above. Under this scenario the 100 Series will revert back to whatever armed status was previously programmed into the device and an additional SMS will be sent. The alarmed mode can also be initiated by pressing the panic button. 4.4.1 Panic Button Your Axesstel Home Alert features a panic button, that when pressed, will immediately activate the siren, as well as alerting your friends and neighbors via SMS and Calls. To activate the panic button simply press the ‘PANIC’ button which is located on your main unit. Panic Please note: Once the panic button has been activated it can be disabled by the keypad only, not remotely by SMS application nor key fob. 58 4.5 Additional Functions&Features This section lists some of the additional functionality and features included in your Axesstel Home Alert 4.5.1 Audio Monitoring/2-Way Communication You can dial in to your Axesstel Home Alert and the speaker in the 100 Series allows you to monitor the surroundings. Using the speaker and microphone also allows you to call in and have a 2-way conversation with your children or whoever is in the vicinity. 4.5.2 Tamper Prevention The Axesstel Home Alert possesses tamper prevention functionality. When the base unit is tampered with (in both Away and Stay modes) an alarm is triggered and alerts are sent. If no disarmed SMS is received 30 seconds it is an indication that the system may be smashed. 4.5.3 Audible Siren The Axesstel Home Alert possesses a siren that will sound when a sensor is triggered. The siren provides a sound equivalent to that of an omni-directional source with a pressure level of over 80 decibels. 59 4.5.4 Axesstel Home Alert Accessories The list of items below are accessories for the 100 Series Axesstel Home Alert available through Axesstel’s distribution network. Contact your point of purchase for availability. AZ100 - Motion Sensor AZ112 - Window/Door Sensor AZ300.-.4-Button Key Fob AZ310.- Panic Key Fob 60 5. AX240 Smartphone Application The below sections define the Smartphone Application for the Axesstel Home Alert 200 Series. When the device is set up, a phone number must be manually entered into the main unit in order for it to be recognized from the app. Once in programming mode this can be done by one of the two methods below: Func Key31Func KeySMS #1SMS #1Func Key or Func Key31Func Key00Func Key Then call from phone number 5.1 AX240 App for Android The AX240 App for android is available from Google Play. 1. Phone is powered on and registered in the network andis Preconditions able to launch Google Play Procedure 1. Open Google Play 2. Search for AX240 App 3. Download the application to the device 61 5.2 AX240 App for iPhone The AX240 app for iPhone is available from the Apple App Store 1. Phone is powered on Preconditions 2. Launch App Store Procedure 1. Open App Store 2. Search for AX240 App 3. Download the application to the device 5.3 AX240 App creating user account (Android/iOS) Preconditions 1. Phone is powered on 2. The AX240 application has been downloaded and open 62 Done Optional Select Device 63 64 5.4 Manage Call Numbers (Android/iOS) Preconditions 1. Phone is powered on 2. The AX240 application has been downloaded 3. The SMS number (of the phone using this App) has already been added in the AX240 Add Call number Read numbers from AX140 Add from Phone Book iPhone only; must press Send. Send number to AX240 Delete number from AX240 65 5.5 Manage SMS Numbers(Android/iOS) Preconditions 1. Phone is powered on 2. The AX240 application has been downloaded 3. The SMS number (of the phone using this App) has already been added in the AX240 Pre-entered SMS number Add from Phone Book Send number to AX240 Delete number from AX240 66 iPhone only; must press Send. 5.6 Delay Time (Entry/Exit ) Preconditions 1. Phone is powered on 2. The AX240 application has been downloaded 3. The SMS number (of the phone using this App) has already been added in the AX240 67 iPhone only; must press Send. 68 5.7 Remote Arming/Disarming Preconditions 1. Phone is powered on 2. The AX240 application has been downloaded 3. The SMS number (of the phone using this App) has already been added in the AX240 Read Status Normal Arming Normal Arming; No Siren iPhone only; must press Send. Arm when at Home Arm when at Home, no Siren. Disarm Alarm 69 5.8 Account Info/Device Status (Android/iOS) Preconditions 1. Phone is powered on 2. The AX240 application has been downloaded 3. The SMS number (of the phone using this App) has already been added in the AX240 70 Android iPhone only; must press Send. Status Displayed in SMS Message box. 71 5.9 Event Log Preconditions 72 1. Phone is powered on 2. The AX240 application has been downloaded 3. The SMS number (of the phone using this App) has already been added in the AX240 Z-Wave Interoperability with Z-Wave Devices: Every Z-Wave certified device is designed to work with allother Z-Wave certified devices. The Z-Wave network canintegrate devices of various classes, and these devices canbe made by different manufacturers. The AX140 is a dedicated controller; since it uses the Basic Command Class, it can provide limited control of other Z-Wave devices using this command class. Wireless range: This device has an open air line of sight transmission distance of 100 feet which complies with the Z-Wave standards. Performance can varydepending on the amount of objects between Z-Wave devices suchas walls and furniture. Every installed Z-Wave device willact as a signal repeater allowing devices to talk to each other and will findalternate routes/paths, in the case of a reception dead spot. Radio frequency limitations: 1. Each wall or object (i.e.: refrigerator, bookshelf, large TV, etc) canreduce the maximum range of 65 feet by up to 25 to 30%. 73 2. Plasterboard and wooden walls block less of the radio signal thenconcrete, brick or tile walls which will have more of an effect onsignal strength. 3. Wall mounted Z-Wave devices will also suffer a loss of range asthey are housed in metal junction boxes which could reduce therange by up to 25 to 30%. Z-Wave basic terminology: Include /Exclude: Includeand exclude are the Z-Wave terms used to describe adding,removing or deleting devices to or from the control network. Replicate: This is the Z-Waveterm for copying or transferringthe Z-Wave network data (all devices) to anew controller. This process isalso used to update secondarycontrollers after changes havebeen made to the controlnetwork with the primarycontroller. Functional Overview: This device is based on the Z-Wave Controller Library and works with devices that support the following Z-Wave Device/Command Classes: Z-Wave device type: Basic Device Class: BASIC_TYPE_CONTROLLER Generic Device Class: GENERIC_TYPE_STATIC_CONTROLLER 74 Specific Device Class: SPECIFIC_TYPE_NOT_USED Z-Wave Command Class COMMAND_CLASS_BASIC COMMAND_CLASS_SENSOR_BINARY COMMAND_CLASS_VERSION Controlled NO YES YES Supported YES NO YES COMMAND_CLASS_MANUFACTURER_SPECIFIC YES YES COMMAND_CLASS_WAKE_UP YES NO COMMAND_CLASS_ALARM YES NO COMMAND_CLASS_CONTROLLER_REPLICATION NO YES 75 Compatible Devices: Z-Wave devices may vary; follow the instructions in the User’s Guide for your specific device when adding and deleting devicesinto the Z-Wave network. Not all features are supported for off-the-shelf Z-Wave devices. Basic Z-Wave Functions: rd Adding 3 party vendor Z-Wave device; please refer to the instructions for the Z-Wave device that you are installing. Inclusion: Add a Z-Wave enabled device On AX140 enter the command [#password75 Func-Key]; on other ZWave device [Press switch to enter inclusion mode (see manufactures instructions for device)] Exclusion: Remove a Z-Wave enabled device. On AX140 enter the command [#password70Func-Key]; on other ZWave device [Press switch to enter inclusion mode (see manufactures instructions for device)] 76 Association: After inclusion, define the relationship between devices (primary/secondary), by specifying one as primary to control the other secondary device. On AX140 enter the command [#password81Group IDFunc-Key]; on the other Z-Wave sensor [Click the button in secondary sensor first then in the primarysensor; this will add the primary sensor to secondary sensor association group(see manufactures instructions for device)] If no Group ID is found, user can specify (example “1”). To Remove the Association (primary sensor from secondary sensor): On AX140 enter the command [#password82Group IDFunc-Key]. Manual Association to the AX140 Controller: On AX140 enter the command [#password83Group IDFunc-Key]; Click the Z-Wave button on the primary sensor will add it to Controller Association Group. To Remove the primary sensor Association Group: On AX140 enter the command [#password84Group IDFunc-Key] 77 78 Learn Mode: How to make the AX140 become a secondary controller. On AX140 enter the command [#password85Func-Key]. Click Z-Wave button on the primary controller. Controller Shift: How to go back/shift back to primary controller. On AX140 enter the command [#password86Func-Key]. Click Z-Wave button on the secondary controller. Operating Specifications 1. Base Unit AX240 Item Air Interface RF Frequency LED Interface Special Features Tone Call Features Battery Power adapter Description CDMA2000 1X-Advanced 800MHz/1900MHz Dual Band 2 RJ-11 Ports (bridged), Max 4 REN DC Power Jack Power On/Off Button TNC Connector for CDMA antenna AGPS for E911 Service Automatic Sending Caller ID DTMF, Bellcore Dial, No Service, Howler, Stutter, Menu OK, Menu NOK Hook Flash, Call Waiting, Call Forwarding, Three-Way Calling 1600mAh Li-Ion rechargeable 5V/2A 79 Size Weight Operating Temperature Operating Humidity 6.8*5.0*1.3 inches (174*128*34 mm) 9 ounces (255g) (without battery) -13~140 F (-25~+60 C) 0% to 95% 2. Alert Panel AZ900 Item CDMA 2000/1XRTT Size Weight Antenna Z-Wave 908.42MHz LED Key SMS numbers CALL numbers Zones Power adapter Description 800/1900 MHz 7.8*4.9*1.5 inches (198*126*38 mm) 12 ounces (340g) CDMA Dual Band antenna Up to 100 feet line of sight 10 16 3 phone numbers 5 phone numbers 4 zones 5V/2A 80 Battery Z-Wave Band Frequency RSSI Operating Temperature Storage Temperature Humidity 9V 908.42MHz -102dBm 14~122 F (-10~+50 C) -4~158 F (-20~+70 C) 0% to 95% 3. Motion Sensor AZ100 Item Description Detection mode Passive infrared signal (PIR) Size 3.3*2.5*1.8 inches (85*65*45 mm) Weight 2.8 ounces (80g) Antenna Build in Z-Wave antenna Transmit distance Up to 100 feet line of sight Detection range 23-39.4 ft. (7-12 m) LED Red & Green Motion sensitivity adjust 3 levels Tamper switch Support 81 Battery Z-Wave Band Frequency RSSI Working Temperature Storage Temperature Humidity 9V 908.42MHz -102dBm 32~122 F (0~+50 C) 14~176 F (-10~+80 C) 0% to 95% Safety Information This device complies with Part 15 of the FCC Rules. Its operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This 82 product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this product does cause harmful interference to radio or television reception, which can be determined by turning the equipment offand on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 83 Radiation Exposure Statement: This device meets the government’s requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. The exposure standard for wireless device employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg. *Tests for SAR are conducted using standard operating positions accepted by the FCC with the device transmitting at its highest certified power level in all tested frequency bands. AX240 Series v0.4 20130816 AXESSTEL INC. 6815 Flanders Drive Ste. 210 San Diego, CA 92121, USA www.axesstel.com 84 © Axesstel Inc, All Rights Reserved 85
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Encryption : Standard V2.3 (128-bit) User Access : Print, Extract, Print high-res Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39 Create Date : 2013:09:03 17:41:12+08:00 Creator Tool : Microsoft® Office Word 2007 Modify Date : 2013:09:03 17:41:26+08:00 Metadata Date : 2013:09:03 17:41:26+08:00 Format : application/pdf Creator : Nelesh Kotecha Producer : Microsoft® Office Word 2007 Document ID : uuid:26cd8a65-f941-4833-aa49-12970db0d44d Instance ID : uuid:1d5b60ca-2682-4c2b-9df6-d8f73e591874 Page Count : 86 Language : zh-TW Author : Nelesh KotechaEXIF Metadata provided by EXIF.tools