AzureWave Technologies CM286NF IEEE 802.11 1X1 ac/a/b/g/n Wireless LAN +Bluetooth NGFF Module User Manual
AzureWave Technologies, Inc. IEEE 802.11 1X1 ac/a/b/g/n Wireless LAN +Bluetooth NGFF Module Users Manual
Users Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3442157 |
| Application ID | 9w0Q9TpgvZEG2WndOfJbkw== |
| Document Description | Users Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 68.43kB (855355 bits) |
| Date Submitted | 2017-06-28 00:00:00 |
| Date Available | 2017-08-12 00:00:00 |
| Creation Date | 2017-06-23 11:49:37 |
| Producing Software | Adobe Acrobat Standard DC 15.6.30306 |
| Document Lastmod | 2017-06-23 15:37:56 |
| Document Title | Users Manual |
| Document Creator | Adobe Acrobat Standard DC 15.6.30306 |
| Document Author: | allen |
AW-CM286NF IEEE 802.11 1X1 ac/a/b/g/n Wireless LAN + Bluetooth NGFF Module Datasheet Version 0.8 (For Cert.) -1- 1. General Description 1-1. Product Overview and Functional Description AzureWave Technologies, Inc. introduces the IEEE 802.11ac/a/b/g/n 1X1 WLAN & Bluetooth NGFF module --- AW-CM286NF. The module is targeted to mobile devices including Notebook, TV, Tablet and Gaming Device which need small package module, low power consumption, multiple interfaces and OS support. By using AW-CM286NF, the customers can easily enable the Wi-Fi, and BT embedded applications with the benefits of high design flexibility, short development cycle, and quick time-tomarket. Compliance with the IEEE 802.11ac/a/b/g/n standard, the AW-CM286NF uses Direct Sequence Spread Spectrum (DSSS), Orthogonal Frequency Division Multiplexing (OFDM), DBPSK, DQPSK, CCK and QAM baseband modulation technologies. A high level of integration and full implementation of the power management functions specified in the IEEE 802.11 standard minimize the system power requirements by using AW-CM286NF. In addition to the support of WPA/WPA2 and WEP 64-bit and 128-bit encryption, the AW-CM286NF also supports the IEEE 802.11i security standard through the implementation of Advanced Encryption Standard (AES)/Counter Mode CBC-MAC Protocol (CCMP), Wired Equivalent Privacy (WEP) with Temporal Key Integrity Protocol (TKIP), Advanced Encryption Standard (AES)/Cipher-Based Message Authentication Code (CMAC), and WLAN Authentication and Privacy Infrastructure (WAPI) security mechanisms. For the video, voice and multimedia applications the AW-CM286NF support 802.11e Quality of Service (QoS). The device also supports 802.11h Dynamic Frequency Selection (DFS) for detecting radar pulses when operating in the 5GHz range. For Bluetooth operation, AW-CM286NF is Bluetooth 4.2 (supports Low Energy). AW-CM286NF supports SDIO for WLAN and BT to the host processor. AW-CM286NF module adopts Marvell’s latest highly-integrated dual-band WLAN & Bluetooth SoC--88W8887. All the other components are implemented by all means to reach the mechanical specification required. -2- 1-2. Key feature: Small footprint: 16mm(L) x 12mm(W) x 1.95mm(H)Max IEEE 802.11ac compliant, 1x1 spatial stream with data rates up to MCS9 (433 Mbps) Bluetooth 4.2 (supports Low Energy (LE)) SDIO 3.0 device interface may be used as host interface for WLAN/Bluetooth PCM/Inter-IC Sound(I2S) for Bluetooth Audio Codec interface support Multiple power saving modes for low power consumption Lead-free design -3- 1-3. Specifications Table Model Name AW-CM286NF Product Description Wireless LAN + Bluetooth Combo Module WLAN Standard IEEE 802.11ac/a/b/g/n, Wi-Fi compliant Bluetooth Standard Bluetooth 4.2 complaint with Bluetooth 2.1+Enhanced Data Rate (EDR) Host Interface Major Chipset Marvell 88W8887 Dimension 12mm x 16mm x 1.95mm(Max) Weight TBD Package LGA SDIO 3.0 device interface (SPI, 1-bit SDIO, 4-bit SDIO transfer modes at full clock range up to 208 MHz) Operating Conditions Voltage 3.3V+- 10% Temperature Operating: -20 ~ 85oC ; Storage: -40 ~ 85oC Electrical Specifications Frequency Range 2.4 GHz ISM radio band / 5 GHz Unlicensed National Information Infrastructure (U-NII) band Number of Channels 802.11a: USA, Taiwan – 12/4 Most European Countries –19 Japan – 4 802.11b: USA, Canada and Taiwan – 11 Most European Countries – 13 France – 4 802.11g: USA, Canada and Taiwan – 11 Most European Countries – 13 Japan – 13 802.11n(HT20): Channel 1~13(2412~2472) 802.11n(HT40): Channel 1~7(2422~2472) Modulation DSSS,OFDM,DBPSK,DQPSK,CCK, 16-QAM, 64-QAM 256-QAM for WLAN GFSK (1Mbps), Π/4 DQPSK (2Mbps) and 8DPSK (3Mbps) for Bluetooth Output Power WLAN G band: 11b:16dBm +/- 2dBm(11M) 11g:14dBm +/- 2dBm (54M) 11n HT20:13dBm +/- 2dBm(MCS7) 11n HT40:12dBm +/- 2dBm(MCS7) WLAN A band: 11a:13dBm +/- 2dBm(54M) 11n HT20:12dBm +/- 2dBm(MCS7) 11n HT40:11dBm +/- 2dBm(MCS7) 11ac VHT_20:11dBm +/- 2dBm(MCS8) 11ac VHT_40:10dBm +/- 2dBm(MCS9) 11ac VHT_80: 7dBm +/- 2dBm(MCS9) Bluetooth: Class 2 :2dBm +/- 2dBm -4- Receive Sensitivity WLAN: WLAN G band : 11b:-87dBm (11M) 11g:-73dBm (54M) 11n:HT20 -70dBm (MCS7) HT40 -68dBm (MCS7) WLAN A band: 11a: -68dBm (54M) 11n HT20:-66dBm (MCS7) 11n HT40:-64dBm(MCS7) 11ac VHT_20: -61dBm(MCS8) 11ac VHT_40: -58dBm(MCS9) 11ac VHT_80: -52dBm(MCS9) Bluetooth: BDR:-88dBm(DH1) EDR:-91dBm(2DH5) BLE:-94.5dBm Data Rates WLAN 802.11b: 1, 2, 5.5, 11Mbps 802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54Mbps 802.11n: up to 150Mbps 802.11ac:up to 86.7Mbps (20MHz channel) 802.11ac:up to 200Mbps (40MHz channel) 802.11ac:up to 433Mbps (80MHz channel) Bluetooth Bluetooth 2.1+EDR data rates of 1,2, and 3Mbps ESD Rating HBM: >2KV per MIL-STD-883H Method 3015.8 CDM:>500V per JEDEC EIA/JESD22-C101E Operating Range Open Space: ~300m ; Indoor: ~100m for WLAN Minimum 10 m indoor for Bluetooth The transmission speed may vary according to the environment) Security Operating System Compatibility WAPI WEP 64-bit and 128-bit encryption with H/W TKIP processing WPA/WPA2 (Wi-Fi Protected Access) AES-CCMP hardware implementation as part of 802.11i security standard Linux (Android, Meego), More information please contact Azurewave FAE. *WiFi /BT power & sensitivity measure @ module out -5- 2. Electrical Characteristic 2-1.Absolute Maximum Ratings Symbol VDD_3V3 VIO VIO_SD Parameter 3.3V input Host I/O power supply SDIO power supply Condition Min Typ Max Units -- -- 3.3 4.0 3.3 4.0 2.5 3.0 1.8 2.2 3.3 4.0 1.8 2.2 -- -- -- -- 2-2.Recommanded Operating Conditions Symbol VBAT_IN VIO VIO_SD Parameter LDO VBAT input Condition Min Typ Max Units -- 2.7 3.3 3.63 2.97 3.3 3.63 2.25 2.5 2.75 1.62 1.8 1.98 2.97 3.3 3.63 1.62 1.8 1.98 1.8V/2.5V/3.3V digital I/O power supply -- 1.8V/3.3V digital I/O SDIO power supply -- -6- 2-3.Clock Specifications 2-3-1 External Sleep Clock Timing External Sleep Clock is necessary for two reasons: 1. Auto frequency Detection. This is where the internal logic will bin the Ref clock source to figure out what is the reference clock frequency is. This is done so no strapping is needed for telling 8887 what the ref clock input is. 2. Allow low current modes for BT to enter sleep modes such as sniff modes. The AW-CM286NF external sleep clock pin is powered from the 1.8V voltage supply. Symbol Parameter Min Typ Max Units CLK Clock Frequency Range 32 or 32.768 -50ppm 32 or 32.768 32 or 32.768 +50ppm KHz THIGH Clock high time 40 -- -- ns TLOW Clock low time 40 -- -- ns TRISE Clock rise time -- -- ns TFALL Clock fall time -- -- ns 2-4. Reset Configuration The AW-CM286NF is reset to its default operating state under the following conditions: Power-on reset (POR) Software/Firmware reset External pin reset (RESETn) 2-4-1. Internal Reset The AW-CM286NF device is reset, and the internal CPU begins the boot sequence when any of the following internal reset events occur: Device receives power and VDDL supplies rise (triggers internal POR circuit) External pin (PDn) assertion will generate POR 2-4-2. External Reset The AW-CM286NF is reset when PDn pin is asserted low and the internal CPU begins the boot sequence when the PDn pin transitions from low to high. -7- 2-5. Power up Timing Sequence -8- 3. Host Interfaces 3-1. SDIO Interface The AW-CM286NF supports a SDIO device interface that conforms to the industry standard SDIO Full-Speed card specification and allows a host controller using the SDIO bus protocol to access the Wireless module device. The AW-CM286NF acts as the device on the SDIO bus. The host unit can access registers of the SDIO interface directly and can access shared memory in the device through the use of BARs and a DMA engine. The SDIO device interface main features include: Supports SDIO 3.0 Standard On-chip memory used for CIS Supports SPI, 1-bit SDIO, and 4-bit SDIO transfer modes Special interrupt register for information exchange Allows card to interrupt host 3-1-1. SDIO Interface Signal Description Signal Pin Name Name SD_CLK CLK Type Description I/O SDIO 1-bit mode: Clock SDIO SPI mode: Clock SD_CMD CMD I/O SDIO 1-bit mode: Command line SDIO SPI mode: Data input SD_DAT[3] DAT3 I/O SDIO 4-bit mode: Data line bit [3] SDIO 1-bit mode: Not used SDIO SPI mode: Chip select (active low) SD_DAT[2] DAT2 I/O SDIO 4-bit mode: Data line bit [2] or Read Wait (optional) SDIO 1-bit mode: Read Wait (optional) SDIO SPII mode: Reserved SD_DAT[1] DAT1 I/O SDIO 4-bit mode: Data line bit [1] SDIO 1-bit mode: Interrupt SDIO SPI mode: Interrupt SD_DAT[0] DAT0 I/O SDIO 4-bit mode: Data line bit [0] SDIO 1-bit mode: Data line SDIO SPI mode: Data output -9- 3-1-2. Default Speed, High Speed Modes (3.3V) SDIO Protocol Timing Diagram – Default Speed Mode (3.3V) SDIO Protocol Timing Diagram – HighSpeed Mode (3.3V) Table shows SDIO Timing Data—Default Speed, High Speed Modes (3.3V) NOTE: Over full range of values specified in the Recommended Operating Conditions unless otherwise specified. - 10 - 3-2. PCM Interface 3-2-1. PCM Timing Specification – Master Mode - 11 - 3-2-2. PCM Timing Specification – Slave Mode - 12 - 4. Pin Definition Pin No Definition Basic Description Type GPIO[15]/TMS JTAG controller select GPIO[14]/TCK JTAG test clock GPIO[16]/TDI JTAG test data(input) VDD_3V3 3.3V Analog RF Power Supply VDD_3V3 3.3V system power supply input GND GPIO[17]/TDO System Ground Pin JTAG test data(output) NC No connect -- NC No connect -- 10 NC No connect -- 11 GPIO[1] GPIO[1] 12 NC No connect -- 13 NC No connect -- 14 NC No connect -- 15 NC No connect -- 16 NC No connect -- 17 GND 18 NC No connect -- 19 NC No connect -- 20 GND 21 NC No connect -- 22 NC No connect -- 23 GND 24 NC No connect -- 25 NC No connect -- 26 GND 27 SLP_CLK System Ground Pin System Ground Pin System Ground Pin System Ground Pin Sleep Clock Input Used for WLAN and Bluetooth lowpower modes. External sleep clock of 32.768 KHz must be used for auto reference clock calibration and for WLAN/Bluetooth low power operation. - 13 - Pin No Definition Basic Description Type 28 GPIO[13] 29 NC No connect -- 30 NC No connect -- 31 GPIO[12] GPIO[12] -- 32 GND 33 NC No connect -- 34 NC No connect -- 35 GND 36 NC No connect -- 37 NC No connect -- 38 GND 39 NC No connect -- 40 NC No connect -- 41 GND 42 GPIO[0]/CLK_REQ 43 NC 44 VIO_SD 45 GPIO[13] System Ground Pin System Ground Pin System Ground Pin System Ground Pin GPIO[0] (input/output) No connect -- 1.8V/3.3V Digital I/O SDIO Power Supply PDn Full Power Down (input) (active low) 46 NC No connect -- 47 SD_DAT[3] SDIO Data line Bit[3] I/O 48 SD_DAT[2] SDIO Data line Bit[2] I/O 49 SD_DAT[1] SDIO Data line Bit[1] I/O 50 SD_DAT[0] SDIO Data line Bit[0] I/O 51 SD_CMD SDIO Command/response (input/output) I/O 52 SD_CLK SDIO Clock input 53 NC 54 GPIO[10] GPIO[10] (input/output) I/O 55 GPIO[8] GPIO[8] (input/output) I/O 56 GPIO[9] GPIO[9] (input/output) I/O 57 GPIO[11] GPIO[11] (input/output) I/O 58 GPIO[7]/PCM_SYNC GPIO[7] (input/output) I/O No Connect - 14 - Pin No Definition Basic Description Type 59 GPIO[4]/PCM_IN GPIO[4] (input/output) 60 GPIO[5]/PCM_OUT GPIO[5] (input/output) 61 GPIO[6]/PCM_CLK GPIO[6] (input/output) I/O 62 GND 63 NC 64 GPIO[2]/WLAN_LED 65 GPIO[3]/BT_LED 66 System Ground Pin No connect -- LED_OUT_WLAN (output) LED_OUT_BT (output) NC No connect -- 67 NC No connect -- 68 GND 69 NC No connect -- 70 NC No connect -- 71 GND 72 NC No connect -- 73 VIO Digital I/O Power Supply 74 GND System Ground Pin 75 GND System Ground Pin 76 GND System Ground Pin 77 GND System Ground Pin 78 GND System Ground Pin 79 GND System Ground Pin 80 GND System Ground Pin 81 GND System Ground Pin 82 GND System Ground Pin 83 GND System Ground Pin 84 GND System Ground Pin 85 GND System Ground Pin 86 GND System Ground Pin 87 GND System Ground Pin 88 GND System Ground Pin 89 GND System Ground Pin System Ground Pin System Ground Pin - 15 - Pin No Definition Basic Description 90 GND System Ground Pin 91 GND System Ground Pin 92 GND System Ground Pin 93 GND System Ground Pin 94 GND System Ground Pin 95 GND System Ground Pin 96 GND System Ground Pin G1 GND System Ground Pin G2 GND System Ground Pin G3 GND System Ground Pin G4 GND System Ground Pin G5 GND System Ground Pin G6 GND System Ground Pin G7 GND System Ground Pin G8 GND System Ground Pin G9 GND System Ground Pin G10 GND System Ground Pin G11 GND System Ground Pin G12 GND System Ground Pin G13 GND System Ground Pin G14 GND System Ground Pin G15 GND System Ground Pin G16 GND System Ground Pin G17 GND System Ground Pin G18 GND System Ground Pin G19 GND System Ground Pin G20 GND System Ground Pin G21 GND System Ground Pin G22 GND System Ground Pin - 16 - Type 5. Mechanical Information 5-1. Package Outline Drawing - 17 - 5-2. Module PCB Layout Footprint - 18 - 6. Shipping Information 6-1 1 UNIT DESICCANT AFFIX PACKING LABEL HUMIDITY INDICATOR CARD 6-2 AFFIX PACKING LABEL 6-3 PINK BUBBLE WRAP - 19 - 6-4 生产标签 AFFIX PACKING LABEL 6-5 1 Carton= 5 Boxes TRANSPARENT SEALING TAPE AFFIX PACKING LABEL 6-6 Note: 1 tape reel = 1 box = 1,500pcs 1 carton = 5 boxes = 5 * 1,500pcs=7,500pcs - 20 - FCC Statement: FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. IMPORTANT NOTE: This module is intended for OEM integrator. The OEM integrator is responsible for the compliance to all the rules that apply to the product into which this certified RF module is integrated. Additional testing and certification may be necessary when multiple modules are used. USERS MANUAL OF THE END PRODUCT: In the users manual of the end product, the end user has to be informed to keep at least 20 cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. If the labelling area is small than the palm of the hand, then additional FCC part 15.19 statement is required to be available in the users manual: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT: The final end product must be labeled in a visible area with the following " Contains TX FCC ID: TLZ-CM286NF ". - 21 - If the labelling area is larger than the palm of the hand, then the following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. Ant. Ant. Brand Holder Brand Holder P/N SE-ECX10-001 Smart Approach Co.,Ltd. SE-ECX10-002 Smart Approach Co.,Ltd. Smart Approach Co.,Ltd. SE-ECX10-003 Smart Approach Co.,Ltd. SE-ECX10-004 Smart Approach Co.,Ltd. SE-ECX10-005 SE-ECX10-006 Smart Approach Co.,Ltd. 2.4G Antenna Type Connector PIFA Antenna PIFA Antenna PIFA Antenna PIFA Antenna PIFA Antenna PIFA Antenna I-PEX I-PEX I-PEX I-PEX I-PEX I-PEX True Gain = antenna gain + cable loss (dBi) 5G B1 5G B2 5G B3 -0.94 1.42 1.42 -1.67 -0.29 -0.33 1.04 0.92 0.92 0.31 0.93 0.28 1.01 0.07 0.07 0.64 0.38 -0.52 Note1: There are 6 antennas in the antenna table list. - 22 - 5G B4 0.58 1.37 2.16 1.37 2.59 -1.11 0.34 -0.49 2.59 -1.37 -0.68 -0.68 IC Statement: This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. Pour les produits disponibles aux États-Unis / Canada du marché, seul le canal 1 à 11 peuvent être exploités. Sélection d'autres canaux n'est pas possible. This radio transmitter (IC: 6100A-CM286NF) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Le présent émetteur radio (IC: 6100A-CM286NF) a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur. Ant. Ant. Brand Holder Brand Holder P/N Smart Approach Co.,Ltd. SE-ECX10-001 Smart Approach Co.,Ltd. SE-ECX10-002 Smart Approach Co.,Ltd. SE-ECX10-003 SE-ECX10-004 Smart Approach Co.,Ltd. SE-ECX10-005 Smart Approach Co.,Ltd. SE-ECX10-006 Smart Approach Co.,Ltd. 2.4G Antenna Type Connector PIFA Antenna PIFA Antenna PIFA Antenna PIFA Antenna PIFA Antenna PIFA Antenna I-PEX I-PEX I-PEX I-PEX I-PEX I-PEX True Gain = antenna gain + cable loss (dBi) 5G B1 5G B2 5G B3 -0.94 1.42 1.42 -1.67 -0.29 -0.33 1.04 0.92 0.92 0.31 0.93 0.28 1.01 0.07 0.07 0.64 0.38 -0.52 Note1: There are 6 antennas in the antenna table list. - 23 - 5G B4 0.58 1.37 2.16 1.37 2.59 -1.11 0.34 -0.49 2.59 -1.37 -0.68 -0.68 Dynamic Frequency Selection (DFS) for devices operating in the bands 5250- 5350 MHz, 54705600 MHz and 5650-5725 MHz. Sélection dynamique de fréquences (DFS) pour les dispositifs fonctionnant dans les bandes 5250-5350 MHz, 54705600 MHz et 5650-5725 MHz. The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems. les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux. The maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit. le gain maximal d’antenne permis pour les dispositifs utilisant les bandes 5250-5350 MHz et 5470-5725 MHz doit se conformer à la limite de p.i.r.e. The maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-pointto-point operation as appropriate. le gain maximal d’antenne permis (pour les dispositifs utilisant la bande 5725-5850 MHz) doit se conformer à la limite de p.i.r.e. spécifiée pour l’exploitation point à point et non point à point, selon le cas. For indoor use only. Pour une utilisation en intérieur uniquement. IMPORTANT NOTE: IC Radiation Exposure Statement: This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. IMPORTANT NOTE: This module is intended for OEM integrator. The OEM integrator is responsible for the compliance to all the rules that apply to the product into which this certified RF module is integrated. Additional testing and certification may be necessary when multiple modules are used. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. USERS MANUAL OF THE END PRODUCT: In the users manual of the end product, the end user has to be informed to keep at least 20 cm separation with the antenna while this end product is installed and operated. The end user has - 24 - to be informed that the IC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT: The final end product must be labeled in a visible area with the following " Contains IC: 6100ACM286NF ". The Host Model Number (HMN) must be indicated at any location on the exterior of the end product or product packaging or product literature which shall be available with the end product or online. - 25 - FCC Statement: FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. IMPORTANT NOTE: This module is intended for OEM integrator. The OEM integrator is responsible for the compliance to all the rules that apply to the product into which this certified RF module is integrated. Additional testing and certification may be necessary when multiple modules are used. USERS MANUAL OF THE END PRODUCT: In the users manual of the end product, the end user has to be informed to keep at least 20 cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. If the labelling area is small than the palm of the hand, then additional FCC part 15.19 statement is required to be available in the users manual: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT: The final end product must be labeled in a visible area with the following " Contains TX FCC ID: TLZ-CM286NF ". If the labelling area is larger than the palm of the hand, then the following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. Ant. Brand Holder Brand Holder P/N Antenna Type Connector Smart Approach Co.,Ltd. SE-ECX10-001 PIFA Antenna I-PEX Smart Approach Co.,Ltd. SE-ECX10-002 PIFA Antenna I-PEX Smart Approach Co.,Ltd. SE-ECX10-003 PIFA Antenna I-PEX Smart Approach Co.,Ltd. SE-ECX10-004 PIFA Antenna I-PEX Smart Approach Co.,Ltd. SE-ECX10-005 PIFA Antenna I-PEX Smart Approach Co.,Ltd. SE-ECX10-006 PIFA Antenna I-PEX Ant. True Gain = antenna gain + cable loss (dBi) 2.4G 5G B1 5G B2 5G B3 5G B4 -0.94 1.42 1.42 0.58 2.16 -1.67 -0.29 -0.33 1.37 1.37 1.04 0.92 0.92 2.59 2.59 0.31 0.93 0.28 -1.11 -1.37 1.01 0.07 0.07 0.34 -0.68 0.64 0.38 -0.52 -0.49 -0.68 Note1: There are 6 antennas in the antenna table list. IC Statement: This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. Pour les produits disponibles aux États-Unis / Canada du marché, seul le canal 1 à 11 peuvent être exploités. Sélection d'autres canaux n'est pas possible. This radio transmitter (IC: 6100A-CM286NF) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Le présent émetteur radio (IC: 6100A-CM286NF) a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur. Ant. Brand Holder Brand Holder P/N Antenna Type Connector Smart Approach Co.,Ltd. SE-ECX10-001 PIFA Antenna I-PEX Smart Approach Co.,Ltd. SE-ECX10-002 PIFA Antenna I-PEX Smart Approach Co.,Ltd. SE-ECX10-003 PIFA Antenna I-PEX Smart Approach Co.,Ltd. SE-ECX10-004 PIFA Antenna I-PEX Smart Approach Co.,Ltd. SE-ECX10-005 PIFA Antenna I-PEX Smart Approach Co.,Ltd. SE-ECX10-006 PIFA Antenna I-PEX Ant. True Gain = antenna gain + cable loss (dBi) 2.4G 5G B1 5G B2 5G B3 5G B4 -0.94 1.42 1.42 0.58 2.16 -1.67 -0.29 -0.33 1.37 1.37 1.04 0.92 0.92 2.59 2.59 0.31 0.93 0.28 -1.11 -1.37 1.01 0.07 0.07 0.34 -0.68 0.64 0.38 -0.52 -0.49 -0.68 Note1: There are 6 antennas in the antenna table list. Dynamic Frequency Selection (DFS) for devices operating in the bands 5250- 5350 MHz, 5470-5600 MHz and 5650-5725 MHz. Sélection dynamique de fréquences (DFS) pour les dispositifs fonctionnant dans les bandes 5250-5350 MHz, 5470-5600 MHz et 5650-5725 MHz. The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems. les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux. The maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit. le gain maximal d’antenne permis pour les dispositifs utilisant les bandes 5250-5350 MHz et 5470-5725 MHz doit se conformer à la limite de p.i.r.e. The maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate. le gain maximal d’antenne permis (pour les dispositifs utilisant la bande 5725-5850 MHz) doit se conformer à la limite de p.i.r.e. spécifiée pour l’exploitation point à point et non point à point, selon le cas. For indoor use only. Pour une utilisation en intérieur uniquement. IMPORTANT NOTE: IC Radiation Exposure Statement: This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. IMPORTANT NOTE: This module is intended for OEM integrator. The OEM integrator is responsible for the compliance to all the rules that apply to the product into which this certified RF module is integrated. Additional testing and certification may be necessary when multiple modules are used. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. USERS MANUAL OF THE END PRODUCT: In the users manual of the end product, the end user has to be informed to keep at least 20 cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the IC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT: The final end product must be labeled in a visible area with the following " Contains IC: 6100A-CM286NF ". The Host Model Number (HMN) must be indicated at any location on the exterior of the end product or product packaging or product literature which shall be available with the end product or online.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Author : allen Create Date : 2017:06:23 11:49:37+08:00 Modify Date : 2017:06:23 15:37:56+08:00 Title : Tagged PDF : No XMP Toolkit : Adobe XMP Core 5.6-c015 84.159810, 2016/09/10-02:41:30 Metadata Date : 2017:06:23 15:37:56+08:00 Creator Tool : Adobe Acrobat Standard DC 15.6.30306 Format : application/pdf Creator : allen Document ID : uuid:bad75c09-b96b-4227-bcc5-9151f9bbce9a Instance ID : uuid:de24ef40-5048-4259-9d69-bd6a393c9ca4 Producer : Adobe Acrobat Standard DC 15.6.30306 Page Count : 30EXIF Metadata provided by EXIF.tools